0.3 mm Pitch, 1.0 mm above the board Flexible Printed Circuit ZIF Connectors
FH36 Series
■Features
1. Low-profile and light weight
Weight: Reduced approximately 30%
Board footprint: Reduced approximately 15%
(As compared with Hirose Electric's FH26 Series
connectors
(51 positions)
2. Easy solderability on the PC board
The soldering leads are on 0.6 mm pitch, exiting on
front and back of the connector.
3. Conducive traces on the PCB can run
under the connector
No exposed contacts on the bottom of the connector.
4. Easy FPC insertion and reliable
electrical connection
Proven Flip Lock actuator allows easy insertion of
FPC and provides a tactile sensation when fully
closed, confirming complete electrical and
mechanical connection.
5. FPC position hold
Tabs on each side of the FPC assure correct
placement and hold in the connector prior to
closing of the actuator.
6. Accepts standard FPC thickness
0.2mm thick standard Flexible Printed Circuit (FPC)
can be used. This is the only ultra-low profile ZIF
connector using standard FPC.
7. Board placement with automatic
equipment
Flat upper surface and tape and reel packaging
facilitate vacuum pick-up and placement.
Standard reel packaging contains 5,000
connectors.
8. Halogen-free *
(FH36W Series)
*As defined by IEC61249-2-21
Br-900ppm maximum, Cl-900ppm maximum,
Cl + Br combined-1,500ppm maximum
●Operation
●FPC temporary hold
●Space saving (51 positions shown)
[51 Positions]
●Can be mounted over conductive traces
No exposed contacts on the bottom of
the connector
16.9mm
Metal fittings do not protrude outside of the connector body
2.7mm
1.0mm MAX
(1) Actuator open
(2) Insert FPC
(1) Actuator open
(2) Insert FPC
FPCFPC
ActuatorActuator
(3) Close the actuator
(4) FPC connected
(3) Close the actuator
(4) FPC connected
1
2013.11②
FH36 Series●0.3 mm Pitch, 1.0 mm above the board Flexible Printed Circuit ZIF Connectors
■Specifications
Storage
temperature range
Storage
humidity range
-10 to +50°C (Note 3)
Relative humidity 90%
max. (No condensation)
Note 1: When passing the current through all of the contacts, use 70% of the rated current.
Note 2: Includes temperature rise caused by current flow.
Note 3: The term "storage" refers to products stored for a long period prior to mounting and use.
The operating temperature and humidity range covers the non-conducting condition of installed connectors in
storage, shipment or during transportation.
Item Specification Conditions
Rating
Current rating
Voltage rating
0.2 A DC (Note 1)
30 Vrms AC
Operating
temperature range
Operating
humidity range
-55 to +85°C (Note 2)
Relative humidity 90%
max. (No condensation)
1.Insulation resistance
2.Withstanding voltage
3.Contact resistance
4.Durability
5.Vibration
6.Shock
7.Humidity
(Steady state)
8.Temperature cycle
9.Resistance to
soldering heat
50 Mø min
No flashover or insulation breakdown
100 mø max.
* Including FPC conductor resistance
Contact resistance: 100 mø max.
No damage, cracks, or parts dislocation
No electrical discontinuity of 1 μs or longer
Contact resistance: 100 mø max.
No damage, cracks, or parts dislocation
No electrical discontinuity of 1 μs or longer
Contact resistance: 100 mø max.
No damage, cracks, or parts dislocation
Contact resistance: 100 mø max.
Insulation resistance: 50 Mø min.
No damage, cracks, or parts dislocation
Contact resistance: 100 mø max.
Insulation resistance: 50 Mø min.
No damage, cracks, or parts dislocation
No deformation of components affection performance.
100 V DC
90 Vrms AC / one minute
1 mA
10 cycles
Frequency: 10 to 55 Hz, single amplitude of 0.75 mm
10 cycles in each of the 3 directions
Acceleration of 981m/s2, 6 ms duration,
sine half-wave, 3 cycles in each of the 3 axis
96 hours at a temperature of 40°C and
humidity of 90 to 95%
Temperature:-55ç➝+15ç to +35ç➝+85ç➝+15ç to +35ç
Time: 30➝2 to 3 ➝30➝2 to 3 minutes
5 cycles
1) Reflow: At the recommended temperature profile.
2) Manual soldering: 350ç ± 10ç for 5 seconds
Recommended FPC Thickness: 0.2±0.03mm Gold plated
FH 36 W - 51S - 0.3 SHW (50)
■Ordering information
Series name : FH
Series No. : 36
Blank :Standard
W :Halogen-free
(Flame retardance UL94HB).
Number of positions : 11 to 61
Contact pitch : 0.3mm
Termination type: SMT horizontal staggered mounting type
specifications
(50)…Gold plating with nickel barrier 5,000 pieces/reel
(99)…Gold plating with nickel barrier 500 pieces/reel
1 2 3 4 5 6 7
4
5
3 6
7
Part Material Finish Remarks
Insulator LCP Color: Beige UL94V-0
Actuator PA FH36 series: Dark brown
FH36W series: Light brown UL94HB
Contacts Phosphor bronze Gold plating -----------------
Metal fittings Pure tin reflow plating -----------------
■Materials
1
2
2
FH36 Series●0.3 mm Pitch, 1.0 mm above the board Flexible Printed Circuit ZIF Connectors
■Connector Dimensions
Note 1 : The coplanarity of each terminal lead is within 0.1.
Note 2 : Packaged on tape and reel only. Check packaging specification.
Note 3 : Slight discoloration in color of the plastic compounds does not affect form, fit or function of the connector.
Note 4 : After reflow, the terminal plating may change color, however this does not represent a quality issue.
0.1
110.1
A * *
(2.7)
(0.47) (0.25)
(1.0 MAX)
(2.75)
A±0.15
B±0.1
C±0.1
(1)
(D: FPC insertion slot dimension)
E±0.1
Lot No. indicator
HRS mark
Number of contacts indicator
Cav No.
(0.12)
0.6±0.1
0.6±0.1 (0.12)
0.3±0.1
All dimensions: mm
Tape and reel packaging (5,000 pieces/reel, 500 pieces/reel).
Order by number of reels.
Part Number
FH36-15S-0.3SHW(50)
FH36-17S-0.3SHW(50)
FH36-19S-0.3SHW(50)
FH36-25S-0.3SHW(50)
FH36-29S-0.3SHW(50)
FH36-33S-0.3SHW(50)
FH36-35S-0.3SHW(50)
FH36-45S-0.3SHW(50)
FH36-51S-0.3SHW(50)
FH36-61S-0.3SHW(50)
FH36W-11S-0.3SHW(50)
FH36W-15S-0.3SHW(50)
FH36W-17S-0.3SHW(50)
FH36W-19S-0.3SHW(50)
FH36W-23S-0.3SHW(50)
FH36W-27S-0.3SHW(50)
FH36W-31S-0.3SHW(50)
FH36W-33S-0.3SHW(50)
FH36W-39S-0.3SHW(50)
FH36W-51S-0.3SHW(50)
FH36W-61S-0.3SHW(50)
580-1618-8-50
580-1606-9-50
580-1607-1-50
580-1619-0-50
580-1613-4-50
580-1615-0-50
580-1604-3-50
580-1617-5-50
580-1601-5-50
580-1600-2-50
580-1625-3-50
580-1623-8-50
580-1616-2-50
580-1612-1-50
580-1614-7-50
580-1608-4-50
580-1609-7-50
580-1622-5-50
580-1620-0-50
580-1605-6-50
580-1611-9-50
15
17
19
25
29
33
35
45
51
61
11
15
17
19
23
27
31
33
39
51
61
6.1
6.7
7.3
9.1
10.3
11.5
12.1
15.1
16.9
19.9
4.9
6.1
6.7
7.3
8.5
9.7
10.9
11.5
13.3
16.9
19.9
3.6
4.2
4.8
6.6
7.8
9
9.6
12.6
14.4
17.4
2.4
3.6
4.2
4.8
6
7.2
8.4
9
10.8
14.4
17.4
4.2
4.8
5.4
7.2
8.4
9.6
10.2
13.2
15
18
3
4.2
4.8
5.4
6.6
7.8
9
9.6
11.4
15
18
4.83
5.43
6.03
7.83
9.03
10.23
10.83
13.83
15.63
18.63
3.63
4.83
5.43
6.03
7.23
8.43
9.63
10.23
12.03
15.63
18.63
5.59
6.19
6.79
8.59
9.79
10.99
11.59
14.59
16.39
19.39
4.39
5.59
6.19
6.79
7.99
9.19
10.39
10.99
12.79
16.39
19.39
CL No. Number of contacts A B C D E
3
(Recommended metal mask thickness: t=0.1)
(0.23:Metal mask)
(0.23:Metal mask)
B±0.05
1.67±0.05 0.6±0.050.8±0.05
(0.5:Metal mask)
(0.65:Metal mask)
0.3±0.03
0.3±0.03 0.6±0.05
0.3±0.05
0.6±0.05
0.535±0.05
0.4±0.05
(0.3:Metal mask)
(0.2)
(0.3)
(0.7:Metal mask)
0.95±0.05
C±0.05
0.03±0.05
(3.07)
0.3±0.05
disengagement shift
2.2±0.3
0.1±0.15
0.75±0.1
0.85±0.1
0.6±0.02
1.45±0.1
R
S
J±0.05
(0.2)
0.1±0.02
B±0.03
G±0.1
F±0.1
0.3+0.04
–0.03
0.3+0.04
–0.03
0.3±0.07
0.3±0.02
H±0.05
C±0.03 0.3±0.07
0.2±0.03
3.3±0.3 (Stiffener)
0.9±0.2
Detail R
(0.5)
(0.07)
*RELATIVE POSITIONS OF
POINT A and B
AB
0±0.03
(Lead plated 0.1 MAX)
2.4±0.1
(R0.2)
(0.15)
1.15±0.05
1.65±0.05
R0.2±0.05
R0.2±0.1
R0.2±0.05
(R0.2)
MAX R0.2
Detail S
R0.2±0.05
0.9±0.2
■Recommended PCB mounting pattern and metal mask dimensions
■Recommended FPC Dimensions
All dimensions: mm
Part Number
FH36-15S-0.3SHW(50)
FH36-17S-0.3SHW(50)
FH36-19S-0.3SHW(50)
FH36-25S-0.3SHW(50)
FH36-29S-0.3SHW(50)
FH36-33S-0.3SHW(50)
FH36-35S-0.3SHW(50)
FH36-45S-0.3SHW(50)
FH36-51S-0.3SHW(50)
FH36-61S-0.3SHW(50)
FH36W-11S-0.3SHW(50)
FH36W-15S-0.3SHW(50)
FH36W-17S-0.3SHW(50)
FH36W-19S-0.3SHW(50)
FH36W-23S-0.3SHW(50)
FH36W-27S-0.3SHW(50)
FH36W-31S-0.3SHW(50)
FH36W-33S-0.3SHW(50)
FH36W-39S-0.3SHW(50)
FH36W-51S-0.3SHW(50)
FH36W-61S-0.3SHW(50)
580-1618-8-50
580-1606-9-50
580-1607-1-50
580-1619-0-50
580-1613-4-50
580-1615-0-50
580-1604-3-50
580-1617-5-50
580-1601-5-50
580-1600-2-50
580-1625-3-50
580-1623-8-50
580-1616-2-50
580-1612-1-50
580-1614-7-50
580-1608-4-50
580-1609-7-50
580-1622-5-50
580-1620-0-50
580-1605-6-50
580-1611-9-50
15
17
19
25
29
33
35
45
51
61
11
15
17
19
23
27
31
33
39
51
61
3.6
4.2
4.8
6.6
7.8
9
9.6
12.6
14.4
17.4
2.4
3.6
4.2
4.8
6
7.2
8.4
9
10.8
14.4
17.4
4.2
4.8
5.4
7.2
8.4
9.6
10.2
13.2
15
18
3
4.2
4.8
5.4
6.6
7.8
9
9.6
11.4
15
18
6.04
6.64
7.24
9.04
10.24
11.44
12.04
15.04
16.84
19.84
4.84
6.04
6.64
7.24
8.44
9.64
10.84
11.44
13.24
16.84
19.84
5.6
6.2
6.8
8.6
9.8
11
11.6
14.6
16.4
19.4
4.4
5.6
6.2
6.8
8
9.2
10.4
11
12.8
16.4
19.4
4.8
5.4
6
7.8
9
10.2
10.8
13.8
15.6
18.6
3.6
4.8
5.4
6
7.2
8.4
9.6
10.2
12
15.6
18.6
4.6
5.2
5.8
7.6
8.8
10
10.6
13.6
15.4
18.4
3.4
4.6
5.2
5.8
7
8.2
9.4
10
11.8
15.4
18.4
CL No.
Number of contacts
B C F G H J
4
FH36 Series●0.3 mm Pitch, 1.0 mm above the board Flexible Printed Circuit ZIF Connectors
Copper foil
Cover adhesive
Covering film layer
Reinforcement material adhesive
Stiffener
■Recommended FPC construction
1. Using Single-sided FPC
2. Using Double-sided FPC
3.Precautions
Material Name
Surface treatment
Copper foil
Base adhesive
Base film
Reinforcement material adhesive
Stiffener
Material
Material Thickness
(μm)
Cu 1oz
Thermosetting adhesive
Polyimide 1 mil thick
Thermosetting adhesive
Polyimide 3 mil thick
Total
0.2μm thick gold plated over 1 to 5μm
thick nickel underplating
Covering film layer
Cover adhesive Polyimide 1 mil thick.
3
35
25
25
40
75
203
(25)
(25)
Covering layer film
Cover adhesive
Surface treatment
Through-hole copper
Copper foil
Base adhesive
Base film
Base adhesive Cu 1/2oz
Thermosetting adhesive
Polyimide 1 mil thick
Thermosetting adhesive
Polyimide 1 mil thick
Total
(18)
25
25
25
25
197
Polyimide 1 mil thick
Cu
Cu 1/2oz
Thermosetting adhesive
Polyimide 1 mil thick
Thermosetting adhesive
(25)
(25)
3
15
18
18
25
18
Material Name Material
Material Thickness
(μm)
*
To prevent release of the FPC due to its bending, use of the double sided FPC with copper foil on the back side is NOT
RECOMMENDED.
1. This specification is a recommendation for the construction of the FH36 Series FPC (t=0.2 ±0.03)
2. For details about the construction, please contact the FPC manufacturers.
Connecting side
Back side
Connecting side
Back side
0.2μm thick gold plated over 1 to 5μm
thick nickel underplating
●Contact FPC manufacturer for specific details.
5
FH36 Series●0.3 mm Pitch, 1.0 mm above the board Flexible Printed Circuit ZIF Connectors
■Packaging Specification
●Embossed Carrier Tape Dimensions
(Tape width of 24mm max.)
●Embossed Carrier Tape Dimensions
(Tape width of 32mm min.)
●Reel Dimensions
2±0.154±0.1
(1.5)
(2.95)
(3.85) (1)
(N)
Flat surface, for placement
with automatic equipment.
K±0.3
M±0.1
8±0.1
Ø1.5 +0.1
0
1.75±0.1
(0.3)
Unreeling direction
K±0.3
L±0.1
M±0.1 1.75±0.1
Ø1.5 +0.1
0
1.7 +0.15
0
1.5 +0.1
0
(1.5) 2±0.154±0.1
(N)
(0.3) 8±0.1
Flat surface, for placement
with automatic equipment.
(Q:OUTSIDE)
(P:INSIDE)
(Ø13)
(Ø80)
(Ø380)
(25 pockets min.)
(25 pockets min.)
End section Mounting section
Embossed carrier tape
No connector inserted
Lead section (400mm min.)
No connector inserted
Top cover tape
All dimensions: mm
Part Number
FH36-15S-0.3SHW(50)
FH36-17S-0.3SHW(50)
FH36-19S-0.3SHW(50)
FH36-25S-0.3SHW(50)
FH36-29S-0.3SHW(50)
FH36-33S-0.3SHW(50)
FH36-35S-0.3SHW(50)
FH36-45S-0.3SHW(50)
FH36-51S-0.3SHW(50)
FH36-61S-0.3SHW(50)
FH36W-11S-0.3SHW(50)
FH36W-15S-0.3SHW(50)
FH36W-17S-0.3SHW(50)
FH36W-19S-0.3SHW(50)
FH36W-23S-0.3SHW(50)
FH36W-27S-0.3SHW(50)
FH36W-31S-0.3SHW(50)
FH36W-33S-0.3SHW(50)
FH36W-39S-0.3SHW(50)
FH36W-51S-0.3SHW(50)
FH36W-61S-0.3SHW(50)
580-1618-8-50
580-1606-9-50
580-1607-1-50
580-1619-0-50
580-1613-4-50
580-1615-0-50
580-1604-3-50
580-1617-5-50
580-1601-5-50
580-1600-2-50
580-1625-3-50
580-1623-8-50
580-1616-2-50
580-1612-1-50
580-1614-7-50
580-1608-4-50
580-1609-7-50
580-1622-5-50
580-1620-0-50
580-1605-6-50
580-1611-9-50
15
17
19
25
29
33
35
45
51
61
11
15
17
19
23
27
31
33
39
51
61
16
16
16
24
24
24
24
24
32
32
16
16
16
16
24
24
24
24
24
32
32
----
----
----
----
----
----
----
----
28.4
28.4
----
----
----
----
----
----
----
----
----
28.4
28.4
7.5
7.5
7.5
11.5
11.5
11.5
11.5
11.5
14.2
14.2
7.5
7.5
7.5
7.5
11.5
11.5
11.5
11.5
11.5
14.2
14.2
6.3
6.9
7.5
9.3
10.5
11.7
12.3
15.3
17.1
20.1
5.1
6.3
6.9
7.5
8.7
9.9
11.1
11.7
13.5
17.1
20.1
17.4
17.4
17.4
25.4
25.4
25.4
25.4
25.4
33.4
33.4
17.4
17.4
17.4
17.4
25.4
25.4
25.4
25.4
25.4
33.4
33.4
21.4
21.4
21.4
29.4
29.4
29.4
29.4
29.4
37.4
37.4
21.4
21.4
21.4
21.4
29.4
29.4
29.4
29.4
29.4
37.4
37.4
CL No.
Number of contacts
K L M N P Q
6
FH36 Series●0.3 mm Pitch, 1.0 mm above the board Flexible Printed Circuit ZIF Connectors
■Temperature Profile
HRS test condition
Solder method :Reflow, IR/hot air
Environment :Room air
Solder composition :Paste,
96.5%Sn/3.0%Ag/0.5%Cu
(Senju Metal Industry, Co.,
Ltd.'s
Part Number:M705-221CM5-
32-10.5)
Test board :Glass epoxy
25mm∞50mm∞0.8mm thick
Land dimensions :0.3mm∞0.6mm,
0.3mm∞0.8mm
Metal mask :0.23∞0.5, 0.23∞0.65∞0.1mm
thick
The temperature profiles shown are based on the
above conditions.
In individual applications the actual temperature may
vary,
depending on solder paste type, volume / thickness
and board size / thickness. Consult your solder
paste and equipment manufacturer for specific
recommendations.
25ç (60sec.) (60sec.)
90 sec. to 120 sec.
Preheating Soldering
Start
(ç)
Temperature
0
50
100
150
200
250
MAX 250ç
Time (Seconds)
150ç
200ç
230ç
●Using Lead-free Solder Paste
7
FH36 Series●0.3 mm Pitch, 1.0 mm above the board Flexible Printed Circuit ZIF Connectors
Rotate down the actuator until firmly closed.
3
■Operation and Precautions
Operation
1. FPC insertion procedure. Connector installed on the board.
Lift up the actuator.
Use thumb or index finger.
2. FPC removal
Lift up the actuator
Pull up the FPC at an angle of approximately 10° ①and
than withdrew it from the connector ②.
1
1
Insert the FPC (contact surfaces facing down) at
angle of approximately 10° to the board surface ①,
making sure that the FPC positioning tabs clear the
protrusions on both sides of the connector. Lower
the FPC down ②, parallel to the board surface.
2
FPC contact surface
faces downward
①
②
Protrusions for FPC positioning
10°
125
°
①
②
8
FH36 Series●0.3 mm Pitch, 1.0 mm above the board Flexible Printed Circuit ZIF Connectors
Precautions
Exercise care when handling connectors. Follow recommendations given below.
[Precautions when mounting connectors on the PCB ]
◆Handling before mounting on PCB
Insertion of the FPC or operation of the actuator prior to mounting on the PCB is NOT RECOMMENDED.
◆PC board warpage
Minimize the warpage as much as possible. The connector is straight within 0.1 mm max. Make sure that
the mounting area flatness can accept the connector terminals without causing any failure of the solder
joints.
◆When braking the large PC board into individual boards exercise care NOT to damage the installed
connectors.
◆When attaching the boards or other components with the screws make sure that any stresses will NOT
cause board deflections affecting the mounting areas of the connector.
◆Bending of the board
For a board width of 100 mm, bending of the board must be 0.5 mm max. (Ref to Fig. 1)
100
0.6
0.5MAX
F
Connector
Board
100
0.6
0.5MAX
Connector Board
F
Axis of rotation
2
Assure free rotation of the actuator.
[Precautions during FPC insertion and mating ]
Pay attention to the following points when inserting FPC.
◆Actuator operation
1Do not apply excessive force when opening the actuator prior to FPC insertion. When opening make
sure that the force is applied only to the actuator itself, avoiding touching of the contacts.
Damage to the actuator
Damage to the actuator
Actuator
Fig. 1
9
FH36 Series●0.3 mm Pitch, 1.0 mm above the board Flexible Printed Circuit ZIF Connectors
Precautions
The actuator will rotate 125ç. Do not apply force to rotate
further.
3
When opening or closing the actuator, do so at
the center section.
4
Do not grasp or and lift the actuator (Fig. 2) nor insert
the nail from the back of it (Fig. 3).
5
◆FPC insertion
Do not insert the FPC at any high angle from above.
125°
Protrusions for FPC positioning
10°
Fig. 2 Fig. 3
10
FH36 Series●0.3 mm Pitch, 1.0 mm above the board Flexible Printed Circuit ZIF Connectors
Precautions
As illustrated (Fig. 4) angle insertion may cause electrical discontinuity when the FPC is deflected in use.
◆Verification of the fully closed actuator
The FPC should be fully inserted, with its positioning tabs fully behind the protrusions on both sides of
the connector’s insertion slot (Fig. 5).
Protrusions FPC positioning
FPC positioning tab
[Routing of the FPC (FPC fully inserted / actuator closed) ]
◆Do not apply any pull or upward-directed force to the FPC.
Do not make any sharp bends of FPC close to the immediate exit from the connector (Fig. 6)
•To avert insertion of the FPC at an angle, consideration should be given to securing enough
insertion space when designing the board lay-out. Insertion will be difficult when the FPC is too
short.
•Contact FPC manufacturer for information about the bending specifications.
Opening of the FPC pattern
Fig. 4
Fig. 6
Fig. 5
11
FH36 Series●0.3 mm Pitch, 1.0 mm above the board Flexible Printed Circuit ZIF Connectors
6-3,Nakagawa Chuoh-2-Chome,Tsuzuki-K u,Yokohama-Shi 224-8540,JAPAN
TEL: +81-45-620-3526 Fax: +81-45-591-3726
http://www.hirose.com
http://www.hirose-connectors.com
®
Protrusions for FPC positioning
10°
125
°
Precautions
[Removing of the FPC ]
◆Rotate the actuator to the fully open position (max. angle of 125ç)
Lift the FPC approximately 10ç(making sure that the positioning tabs clear the protrusions on both
sides) and carefully withdraw it from the connector.
[Other Precautions ]
◆Hand Soldering Precautions
When hand soldering:
Do not perform reflow or hand soldering with the FPC inserted in the connector.
Do not apply excessive heat or touch the soldering iron anywhere other than the connector leads.
Do not use excessive amount of solder or flux compounds.
Operation of the actuator or contacts may be affected by excessive amounts of solder or flux com-
1
2
3
12 The contents of this catalog are current as of date of 11/2013. Contents are subject to change without notice for the purpose of improvements.
FH36 Series●0.3 mm Pitch, 1.0 mm above the board Flexible Printed Circuit ZIF Connectors
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Hirose Electric:
FH36-15S-0.3SHW(10) FH36-15S-0.3SHW(50) FH36-17S-0.3SHW(10) FH36-17S-0.3SHW(50) FH36-19S-
0.3SHW(10) FH36-19S-0.3SHW(50) FH36-25S-0.3SHW(10) FH36-25S-0.3SHW(50) FH36-29S-0.3SHW(10) FH36-
29S-0.3SHW(50) FH36-33S-0.3SHW(50) FH36-35S-0.3SHW(10) FH36-35S-0.3SHW(50) FH36-45S-0.3SHW(10)
FH36-45S-0.3SHW(50) FH36-51S-0.3SHW(10) FH36-51S-0.3SHW(50) FH36-61S-0.3SHW(50) FH36W-11S-
0.3SHW(50) FH36W-15S-0.3SHW(50) FH36W-17S-0.3SHW(10) FH36W-17S-0.3SHW(50) FH36W-19S-0.3SHW(10)
FH36W-19S-0.3SHW(50) FH36W-23S-0.3SHW(10) FH36W-23S-0.3SHW(50) FH36W-25S-0.3SHW(50) FH36W-
27S-0.3SHW(10) FH36W-27S-0.3SHW(50) FH36W-31S-0.3SHW(50) FH36W-33S-0.3SHW(50) FH36W-39S-
0.3SHW(10) FH36W-39S-0.3SHW(50) FH36W-51S-0.3SHW(50) FH36W-61S-0.3SHW(10) FH36W-61S-0.3SHW(50)
FH36-61S-0.3SHW(99) FH36-51S-0.3SHW(99) FH36-35S-0.3SHW(99) FH36-17S-0.3SHW(99) FH36-19S-
0.3SHW(99) FH36W-61S-0.3SHW(99) FH36W-19S-0.3SHW(99) FH36-29S-0.3SHW(99) FH36W-23S-0.3SHW(99)
FH36W-17S-0.3SHW(99) FH36-15S-0.3SHW(99) FH36-25S-0.3SHW(99) FH36W-33S-0.3SHW(99) FH36W-15S-
0.3SHW(99) FH36W-11S-0.3SHW(99) FH36W-51S-0.3SHW(99) FH36W-39S-0.3SHW(99) FH36W-31S-0.3SHW(99)
FH36W-25S-0.3SHW(99) FH36-33S-0.3SHW(99) FH36-45S-0.3SHW(99) FH36W-27S-0.3SHW(99)