SII163BCTG100 - Silicon Image - Datasheet.Directory

Technology

SiI 163B

PanelLink Receiver

Data Sheet

Document # SiI-DS-0055-C

SiI 163B PanelLink Receiver

Data Sheet

ii SiI-DS-0055-C

Silicon Image, Inc.

SiI-DS-0055-C

July 2005

Application Information

To obtain the most updated Application Notes and other useful information for your design, please visit the Silicon

Image web site at www.siimage.com, or contact your local Silicon Image sales office.

This manual is copyrighted by Silicon Image, Inc. Do not reproduce, transform to any other format, or

send/transmit any part of this documentation without the expressed written permission of Silicon Image, Inc.

T rademark Acknowledgment

Silicon Image, the Silicon Image logo, PanelLink®, TMDS® and the PanelLink® Digital logo are registered

trademarks of Silicon Image, Inc. VESA® is a registered trademark of the Video Electronics Standards

Association. All other trademarks are the property of their respective holders.

Disclaimer

This document provides technical information for the user. Silicon Image, Inc. reserves the right to modify the

information in this document as necessary. The customer should make sure that they have the most recent data

sheet version. Silicon Image, Inc. holds no responsibility for any errors that may appear in this document.

Customers should take appropriate action to ensure their use of the products does not infringe upon any patents.

Silicon Image, Inc. respects valid patent rights of third parties and does not infringe upon or assist others to

infringe upon such rights.

All information cont ained herein is subject to change without notice.

Revision History

Revision Date Comment

SiI-DS-0055-A 03/02 Full Release

SiI-DS-0055-B 08/04 Added ePad dimensions and Slave SCDT stabilization guideline.

SiI-DS-0055-C 07/05 ePad dimensions fix. Part ordering number update.

SiI 163B PanelLink Receiver

Data Sheet

iii SiI-DS-0055-C

TABLE OF CONTENTS

SiI 163B Pin Diagram ..................................................................................................................................... 1

Functional Description .................................................................................................................................... 2

Electrical Specifications .................................................................................................................................. 3

Absolute Maximum Conditions ................................................................................................................... 3

Normal Operating Conditions ..................................................................................................................... 3

Digital I/O Specifications ............................................................................................................................. 3

DC Specifications........................................................................................................................................ 4

AC Specifications ........................................................................................................................................ 5

Setup and Hold Timings for Data Rates other than 165 MHz ................................................................. 6

Timing Diagrams............................................................................................................................................. 7

Pin Descriptions............................................................................................................................................ 10

Output Pins ............................................................................................................................................... 10

Configuration Pins..................................................................................................................................... 11

Power Management Pins.......................................................................................................................... 11

Differential Signal Data Pins ..................................................................................................................... 12

Reserved Pin............................................................................................................................................. 12

Power and Ground Pins............................................................................................................................ 12

Feature Information ...................................................................................................................................... 13

Dual Link ................................................................................................................................................... 13

Dual Link Configuration Pins................................................................................................................. 13

Dual Link Power Management .............................................................................................................. 16

Dual Link Mode Selection...................................................................................................................... 16

Dual Link Timing Diagrams ................................................................................................................... 17

Clock Detect Function............................................................................................................................... 19

OCK_INV# Function ................................................................................................................................. 19

TFT Panel Data Mapping.......................................................................................................................... 20

Design Recommendations ........................................................................................................................... 27

Differences Between SiI 161A and SiI 163B............................................................................................. 27

Voltage Ripple Regulation......................................................................................................................... 28

Decoupling Capacitors.............................................................................................................................. 29

Series Damping Resistors on Outputs...................................................................................................... 30

Receiver Layout ........................................................................................................................................ 30

Stabilized TMDS Inputs............................................................................................................................. 32

Staggered Outputs and Two Pixels per Clock .......................................................................................... 32

Packaging ..................................................................................................................................................... 33

ePad Enhancement .................................................................................................................................. 33

PCB Thermal Land Area ....................................................................................................................... 34

100-pin TQFP Package Dimensions and Marking Specification .............................................................. 35

Marking Specification ................................................................................................................................ 35

Ordering Information..................................................................................................................................... 35

SiI 163B PanelLink Receiver

Data Sheet

iv SiI-DS-0055-C

LIST OF TABLES

Table 1. Setup and Hold Times at Various Data Rates .................................................................................. 6

Table 2. SiI 163B Dual Link Pin Definitions.................................................................................................. 13

Table 3. SiI 163B Dual Link Pin Configuration............................................................................................. 15

Table 4. DVI-D Connector to SiI 163B for Dual Link Application Pin Connection........................................ 19

Table 5. One Pixel/Clock Mode Data Mapping............................................................................................. 20

Table 6. Two Pixel/Clock Mode Data Mapping ............................................................................................. 20

Table 7. One Pixel/Clock Input/Output TFT Mode – VESA P&D and FPDI-2TM Compliant.......................... 21

Table 8. Two Pixels/Clock Input/Output TFT Mode ...................................................................................... 22

Table 9. 24-bit One Pixel/Clock Input with 24-bit Two Pixels/Clock Output TFT Mode................................ 23

Table 10. 18-bit One Pixel/Clock Input with 18-bit Two Pixels/Clock Output TFT Mode.............................. 24

Table 11. Two Pixels/Clock Input with One Pixel/Clock Output TFT Mode .................................................. 25

Table 12. Output Clock Configuration by Typical Application ....................................................................... 26

Table 13. SiI 161A vs. SiI 163B Pin Differences ........................................................................................... 27

Table 14. SiI 161B vs. SiI 163B Pin Differences ........................................................................................... 27

Table 15. Recommended Components ........................................................................................................ 29

LIST OF FIGURES

Figure 1. Functional Block Diagram ............................................................................................................... 2

Figure 2. Digital Output Transition Times ....................................................................................................... 7

Figure 3. Receiver Clock Cycle/High/Low Times ........................................................................................... 7

Figure 4. Channel-to-Channel Skew Timing .................................................................................................. 7

Figure 5. Output Setup/Hold Timings ............................................................................................................. 8

Figure 6. Output Signals Disabled Timing from Clock Inactive ...................................................................... 8

Figure 7. Wake-Up on Clock Detect ............................................................................................................... 8

Figure 8. Output Signals Disabled Timing from PD# Active ........................................................................... 8

Figure 9. SCDT Timing from DE Inactive or Active ........................................................................................ 9

Figure 10. Two Pixel per Clock Staggered Output Timing Diagram............................................................... 9

Figure 11. SiI 163B Dual Link Block Diagram .............................................................................................. 14

Figure 12. Timing Diagram of Master's Output............................................................................................. 17

Figure 13. Timing Diagram of Slave's Output............................................................................................... 18

Figure 14. Single/Dual Link Timing Diagram ................................................................................................ 18

Figure 15. Block Diagram for OCK_INV#..................................................................................................... 19

Figure 16. Voltage Regulation using TL431 ................................................................................................. 28

Figure 17. Voltage Regulation using LM317 ................................................................................................ 28

Figure 18. Decoupling and Bypass Capacitor Placement............................................................................29

Figure 19. Decoupling and Bypass Schematic............................................................................................. 29

Figure 20. Receiver Output Series Damping Resistors ............................................................................... 30

Figure 21. DVI Dual Link Rx PCB Routing Example – Top View ................................................................. 30

Figure 22. DVI Dual Link Rx PCB Routing Example – Top Signals Top View.............................................. 31

Figure 23. DVI Dual Link Rx PCB Routing Example - Bottom Signals Top View......................................... 31

Figure 24. Stabilizing SCDT ......................................................................................................................... 32

Figure 25. ePad Diagram ............................................................................................................................. 33

Figure 26. ePad Template Layout................................................................................................................. 34

Figure 27. Package Dimensions and Marking Specification ........................................................................ 35

SiI 163B PanelLink® Receiver July 2005

Data Sheet

SiI-DS-0055-C

General Description Features

The SiI 163B receiver uses PanelLink Digital

technology to support high-resolution (24 bit/pixel, 16M

colors) displays up to UXGA and beyond, with dual-link

DVI for a total bandwidth up to 330 megapixels per

second.

All PanelLink products are designed on a scaleable

CMOS architecture, ensuring support for future

performance enhancements while maintaining the

same logical interface. System designers can be

assured that the interface will be stable through a

number of technology and performance generations.

PanelLink Digital technology simplifies PC and display

interface design by resolving many of the system level

issues associated with high-speed mixed signal

design, providing the system designer with a digital

interface solution that is quicker to market and lower in

cost.

• Low Power Operation: 280mA max. current

consumption at 3.3V core operation

• Sync Detect feature for Plug & Display

“Hot Plugging”

• Cable Distance Support: over 5m with twisted-

pair, fiber-optics ready

• Compliant with DVI 1.0

• Low power standby mode

• Automatic entry into standby mode with clock

detect circuitry

• Dual-Link DVI support with two devices

configured as master and slave

SiI 163B Pin Diagram

S_D

SiI 163B

100-Pin TQFP

(Top View)

PD#

PIXS/M_S

GND

VCC

STAG_OUT#/SYNC

SCDT

PDO#

QE0

QE1

QE2

QE3

QE4

QE5

QE6

QE7

OVCC18

OGND

QE8

QE9

QE10

QE11

QE12

QE13

QE14

QE15

OGND

OVCC

QE16

QE17

QE18

QE19

QE20

QE21

QE22

QE23

VCC

GND

CTL1

CTL2

CTL3

OVCC

ODCK

OGND

VSYNC

HSYNC

QO0

QO1

QO21 74

QO20 73

QO19 72

QO18 71

QO17 70

QO16 69

GND 68

VCC 67

QO15 66

QO14 65

QO13 64

QO12 63

QO11 62

QO10 61

QO9 60

QO8 59

OGND 58

OVCC 57

QO7 56

QO6 55

QO5 54

QO4 53

QO3 52

QO2 51

QO22

OCK_INV# 100

RESERVED 99

PGND 98

PVCC 97

EXT_RES 96

AVCC 95

RXC- 94

RXC+ 93

AGND 92

RX0- 91

RX0+ 90

AGND 89

AVCC 88

AGND 87

RX1- 86

RX1+ 85

AVCC 84

AGND 83

AVCC 82

RX2- 81

RX2+ 80

AGND 79

OVCC 78

QO23 77

OGND 76

DIFFERENTIAL SIGNAL

ODD 8-bits RED

EVEN 8-bits RED

ODD 8-bits GREEN

EVEN 8-bits GREEN

ODD 8-bits BLUE

EVEN 8-bits BLUE

CONFIG. PINS

PLL

PWR

MANAGEMENT

GPO

OUTPUT CLOCK

CONTROLS

SiI 163B PanelLink Receiver

Data Sheet

2 SiI-DS-0055-C

Functional Description

The SiI 163B is a DVI 1.0 compliant PanelLink receiver in a compact package. It provides 48 bits for data output

to allow for panel support up to UXGA and dual-link applications. Figure 1 shows the functional blocks of the

chip.

PLL

Termination

Control

Channel

SYNC

Data Recovery

CH2

Data Recovery

CH0

Data Recovery

CH1

VCR

Panel

Interface

Logic

RX2+

RX2-

RXC+

RXC-

RX0+

RX0-

RX1+

RX1-

PDO#

STAG_OUT#

/SYNC

EXT_RES

OCK_INV#

S_D

PIXS/M_S

VCR

SYNC2

SYNC1

SYNC0

Decoder

QE[23:0]

QO[23:0]

ODCK

HSYNC

VSYNC

SCDT

CTL[3:1]

Figure 1. Functional Block Diagram

The PanelLink TMDS core accepts as inputs the three TMDS differential data lines and the differential clock. The

core senses the signals on the link and properly decodes them providing accurate pixel data. The core outputs

the necessary sync signals (HSYNC, VSYNC), clock (ODCK), and a DE signal that goes high when the active

region of the video is present.

The SCDT signal is output when there is active video on the DVI link and the PLL in the TMDS has locked on to

the video. SCDT can be used to trigger external circuitry, indicating that an active video signal is present or used

to place the device in power down when no signal is present (by tying it to PD#). The EXT_RES component is

used for impedance matching.

When Single/Dual Link Mode (S_D) is HIGH, the signals M_S and SYNC are used to select and coordinate

operation of two receivers in a dual-link DVI configuration. In this mode, at frequencies up to 165 MHz, the

master receiver outputs two pixels/clock (48 data bits). At frequencies above 165 MHz, the master outputs even

pixels (24 bits) while the slave receiver outputs odd pixels (24 bits) synchronized with one DE output from the

master.

SiI 163B PanelLink Receiver

Data Sheet

3 SiI-DS-0055-C

Electrical Specifications

Absolute Maximum Conditions

Symbol Parameter Min Typ Max Units

VCC Supply Voltage 3.3V (note 1) -0.3 4.0 V

VI Input Voltage -0.3 VCC+ 0.3 V

VO Output Voltage (note 2) -0.3 VCC+ 0.3 V

TJ Junction Temperature 125

°C

TSTG Storage Temperature -65 150 °C

Notes

1. Permanent device damage may occur if absolute maximum conditions are exceeded.

2. Functional operation should be restricted to the conditions described under Normal Operating Conditions.

Normal Operating Conditions

Symbol Parameter Min Typ Max Units

VCC Supply Voltage 3.0 3.3 3.6 V

VCCN Supply Voltage Noise 100 mVP-P

TA Ambient Temperature (with power applied) 0 25 70 °C

θJA Thermal Resistance

Junction to Ambient – ePad soldered

21 °C/W

θJAU Thermal Resistance

Junction to Ambient – ePad unsoldered

30 °C/W

Silicon Image recommends soldering of ePad to improve thermal performance, especially at highest speeds.

Note

1. θJA value based on 100% soldered down on multi-layer board.

Digital I/O Specifications

Under normal operating conditions unless otherwise specified.

Symbol Parameter Conditions Min Typ Max Units

VIH High-level Input Voltage 2 V

VIL Low-level Input Voltage 0.8 V

VOH High-level Output Voltage 2.4 V

VOL Low-level Output Voltage 0.4 V

VCINL Input Clamp Voltage1 I

CL = -18mA GND -0.8 V

VCIPL Input Clamp Voltage1 I

CL = 18mA IVCC + 0.8 V

VCONL Output Clamp Voltage1 I

CL = -18mA GND -0.8 V

VCOPL Output Clamp Voltage1 I

CL = 18mA OVCC + 0.8 V

IOL Output Leakage Current High Impedance -10 10 µA

Note

1. Guaranteed by design. Voltage undershoot or overshoot cannot exceed absolute maximum conditions

for a pulse of greater than 3 ns or one third of the clock cycle.

SiI 163B PanelLink Receiver

Data Sheet

4 SiI-DS-0055-C

DC Specifications

Under normal operating conditions unless otherwise specified.

Symbol Parameter Conditions Min Typ Max Units

IOHD Output High Drive Data and

Controls

VOUT = 2.4 V; ST = 1

ST = 0

7.4

3.8

12.6

6.4

18.2

9.2

IOLD Output Low Drive Data and

Controls

VOUT = 0.8 V; ST = 1

ST = 0

-11.1

-5.5

-12.6

-6.4

-13.6

-6.9

OUT = 0.4 V; ST = 1

ST = 0

-6.3

-3.2

-6.9

-3.5

-7.6

-3.8

IOHC ODCK, DE High Drive VOUT = 2.4 V; ST = 1

ST = 0

14.7

7.5

23.8

11.5

34.3

17.6

IOLC ODCK, DE Low Drive VOUT = 0.8V; ST = 1

ST = 0

-21.2

-11.1

-26.7

-12.5

-27.5

-13.9

OUT = 0.4 V; ST = 1

ST = 0

-12.3

-6.2

-13.6

-6.8

-15.9

-7.6

VID Differential Input Voltage

Single Ended Amplitude

75 1000 mV

IPD Power-down Current PD#=LOW, No RXC+ input 1 mA

ICLKI Power-down Current PD#=HIGH, No RXC+ input 3 mA

IPDO Receiver Supply Current with

Outputs Powered Down

ODCK=87.5 MHz,

2-pixel/clock mode

CLOAD = 10pF

REXT_SWING = 510 ohm

PDO# = LOW

133 mA

ICCR Receiver Supply Current

ODCK=87.5 MHz,

2-pixel/clock mode

CLOAD= 10pF

REXT_SWING = 510 ohm

Typical Pattern1

240 mA

ODCK=87.5 MHz, 0°C

2-pixel/clock mode

CLOAD = 10pF

REXT_SWING = 510 ohm

Worst Case Pattern2

280 mA

Notes

1. The Typical Pattern contains a gray scale area, checkerboard area, and text.

2. The Worst Case Pattern consists of a black and white checkerboard pattern; each checker is two pixels wide.

SiI 163B PanelLink Receiver

Data Sheet

5 SiI-DS-0055-C

AC Specifications

Under normal operating conditions unless otherwise specified.

Symbol Parameter Conditions Min Typ Max Units

TDPS Intra-Pair (+ to -) Differential Input Skew1 165MHz 245 ps

TCCS Channel to Channel Differential Input Skew1 165MHz 4 ns

TIJIT Worst Case Differential Input Clock Jitter 65 MHz 465 ps

tolerance2,3 112 MHz 270 ps

165 MHz 182 ps

DLHT C

L = 10pF; ST = 1 2.6 ns

Low-to-High Transition Time: Data and Controls

(70°C, 87.5 MHz, 2-pixel/clock, PIXS=1) CL = 5pF; ST = 0 2.7 ns

L = 10pF; ST = 1 2.4 ns

Low-to-High Transition Time: Data and Controls

(70°C, 165 MHz, 1-pixel/clock, PIXS=0) CL = 5pF; ST = 0 3.0 ns

L = 10pF; ST = 1 1.3 ns

Low-to-High Transition Time: ODCK

(70°C, 87.5 MHz, 2-pixel/clock, PIXS=1) CL = 5pF; ST = 0 1.7 ns

L = 10pF; ST = 1 1.4 ns

Low-to-High Transition Time: ODCK

(70°C, 165 MHz, 1-pixel/clock, PIXS=0) CL = 5pF; ST = 0 1.7 ns

DHLT C

L = 10pF; ST = 1 2.8 ns

High-to-Low Transition Time: Data and Controls

(70°C, 87.5 MHz, 2-pixel/clock, PIXS=1) CL = 5pF; ST = 0 3.4 ns

L = 10pF; ST = 1 2.3 ns

High-to-Low Transition Time: Data and Controls

(70°C, 165 MHz, 1-pixel/clock, PIXS=0) CL = 5pF; ST = 0 3.3 ns

L = 10pF; ST = 1 1.1 ns

High-to-Low Transition Time: ODCK

(70°C, 87.5 MHz, 2-pixel/clock, PIXS=1) CL = 5pF; ST = 0 1.5 ns

L = 10pF; ST = 1 1.2 ns

High-to-Low Transition Time: ODCK

(70°C, 165 MHz, 1-pixel/clock, PIXS=0) CL = 5pF; ST = 0 1.5 ns

TSETUP C

L = 10pF; ST = 1 0.9

(1.4)6

Data, DE, VSYNC, HSYNC, and CTL[3:1] Setup

Time to ODCK falling edge (OCK_INV# = 0) or to

ODCK rising edge (OCK_INV# = 1) at 165 MHz CL = 5pF; ST = 0 0.7

(0.5)6

THOLD C

L = 10pF; ST = 1

2.7

(2.3)6

Data, DE, VSYNC, HSYNC, and CTL[3:1] Hold Time

from ODCK falling edge (OCK_INV# = 0) or from

ODCK rising edge (OCK_INV# = 1) at 165 MHz CL = 5pF; ST = 0 3.0

(2.6)6

RCIP ODCK Cycle Time1 (1-pixel/clock) 6.06 40 ns

FCIP ODCK Frequency1 (1-pixel/clock) 25 165 MHz

RCIP ODCK Cycle Time1 (2-pixels/clock) 12.1 80 ns

FCIP ODCK Frequency1 (2-pixels/clock) 12.5 82.5 MHz

RCIH C

L = 10pF; ST = 1 1.7 ns

ODCK High Time4

CL = 5pF; ST = 0 1.3 ns

RCIL C

L = 10pF; ST = 1 2.0 ns

ODCK Low Time4

165 MHz, 1 pixel/clock,

PIXS=0.

CL = 5pF; ST = 0 1.4 ns

TPDL Delay from PD# / PDO# Low to high impedance outputs1 10 ns

THSC Link disabled (DE inactive) to SCDT low1 100 ms

Link disabled (Tx power down) to SCDT low5 250 ms

TFSC Link enabled (DE active) to SCDT high1 25 40 DE edges

TCLKPD Delay from RXC+ Inactive to high impedance outputs RXC+ = 25MHz 10 µs

TCLKPU Delay from RXC+ active to data active RXC+ = 25MHz 100 µs

TST ODCK high to even data output1 0.25 RCIP

TOSK Output Skew from Slave to Master Data buses7 165 MHz 300 300 ps

SiI 163B PanelLink Receiver

Data Sheet

6 SiI-DS-0055-C

Notes on previous table:

1. Guaranteed by design.

2. Jitter defined per DVI 1.0 Specification, Section 4.6 – Jitter Specification.

3. Jitter measured with Clock Recovery Unit per DVI 1.0 Specification, Section 4.7 – Electrical Measurement Procedures.

4. Output clock duty cycle is independent of the differential input clock duty cycle and the IDCK duty cycle.

5. Measured with transmitter powered down.

6. Value in parentheses is specified with OCK_INV#=1.

7. Skew between output data buses when two SiI 163B are wired in master-slave configuration for dual-link. See the

Receiver Layout section on page 30. The ‘minimum’ is the limit of Slave leading Master (slave data output earlier than

master data). The ‘maximum’ is the limit of Slave lagging Master (slave data output later than master data). When the

Slave lags the Master, then the setup time available from Slave data to ODCK (from the Master) is reduced.

Setup and Hold Timings for Data Rates other than 165 MHz

The measurements shown above are minimum setup and hold timings based on the maximum data rate of 165

MHz. To estimate the setup and hold times for slower data rates (for either different resolutions or 2 pixel per

clock mode), the following formula can be used:

Time (at new frequency) = Time (165 MHz) + (Clock Period at new frequency – Clock Period at 165 MHz)/2

For the case of high strength output (ST=1) with a 10pf load, and using the standard ODCK (OCK_INV# = 0),

Table 1 shows the minimum set up and hold times for other speeds as follows:

Table 1. Setup and Hold Times at Various Data Rates

Data Rate (MHz) Clock (ns) Setup (ns) Hold (ns)

112

8.9

17.9

2.3

6.8

4.1

8.6

SXGA 1 pixel/clock

SXGA 2 pixels/clock

135 7.4 1.6 3.4 SXGA+ 1 pixel/clock

67.5

82.5

14.8

12.1

5.3

3.9

7.1

5.7

SXGA+ 2 pixels/clock

UXGA 2 pixels/clock

Designers may want to check whether OCK+INV#=0 or OCK_INV#=1 provides better setup and hold time margin

for their dual-link design. If Slave data lags Master data, which is in part determined by the layout, then the setup

time from Slave to clock may be reduced, and the opposite ODCK edge may be more useful.

SiI 163B PanelLink Receiver

Data Sheet

7 SiI-DS-0055-C

Timing Diagrams

10pF / 5pF

SiI 163B

LHT D

HLT

2.0 V 2.0 V

0.8 V 0.8 V

Figure 2. Digit al Output Transition Times

Note:

1. 10pF loading used at ST=1 and 5pF loading using at ST=0

RCIH

RCIL

RCIP

2.0 V

0.8 V

2.0 V 2.0 V

Figure 3. Receiver Clock Cy cle/High/Low Times

RX0

RX1

RX2

CCS

DIFF=0V

VDIFF=0V

Figure 4. Channel-to-Channel Skew Timing

SiI 163B PanelLink Receiver

Data Sheet

8 SiI-DS-0055-C

Output Timing

OCK_INV# = 1

OCK_INV# = 0

QE[23:0], QO[23:0],

DE, CTL[3:1],

VSYNC, HSYNC

THOLD

TSETUP

Figure 5. Output Setup/Hold Timings

Note

1. Output Data, DE and Control Signals Setup/Hold Times – to ODCK Falling Edge when OCK_INV# = 0, or to ODCK

Rising Edge when OCK_INV# = 1.

2. See also the description of layout guidelines which guarantee limited skew between master and slave outputs in the

Receiver Layout section on page 30.

Figure 6. Output Signals Disabled Timing from Clock Inactive

Figure 7. Wake-Up on Clock Detect

TPDL

QE[23:0], QO[23:0],

DE, CTL[3:1],

VSYNC, HSYNC

PD#

VIL

Figure 8. Output Signals Disabled Timing from PD# Active

RXC+

SCDT

TCLKPU + TFSC

RXC+

Q[35:0], DE,

VSYNC, HSYNC,

CTL[3:1]

TCLKPD

SiI 163B PanelLink Receiver

Data Sheet

9 SiI-DS-0055-C

SCDT

TTFSC

TTHSC

Figure 9. SCDT Timing from DE Inactive or Active

ODCK

QE[23:0]]

QO[23:0]

FIRST D ATA THIRD D ATA

Internal

ODCK * 2

SECOND FOURTH DATA

Figure 10. Two Pixel per Clock Staggered Output Timing Diagram

SiI 163B PanelLink Receiver

Data Sheet

10 SiI-DS-0055-C

Pin Descriptions

Output Pins

Name Pin # Type Description

QE23-

QE0

See

SiI 163B

Diagram

Out Output Even Data[23:0]. Refer to the Dual Link section on page 13 for details.

Output data is synchronized with output data clock (ODCK).

Refer to the TFT Panel Data Mapping section on page 20, which tabulates the

relationship between the input data to the transmitter and output data from the

receiver.

A low level on PD# or PDO# will put the output drivers into a high impedance (tri-

state) mode. A weak internal pull-down device brings each output to ground.

QO23-

QO0

See

SiI 163B

Diagram

Out Output Odd Data[23:0]. Refer to the Dual Link section on page 13 for details.

Output data is synchronized with output data clock (ODCK).

Refer to the TFT Panel Data Mapping section on page 20, which tabulates the

relationship between the input data to the transmitter and output data from the

receiver.

A low level on PD# or PDO# will put the output drivers into a high impedance (tri-

state) mode. A weak internal pull-down device brings each output to ground.

ODCK 44 Out Output Data Clock. This output can be inverted using the OCK_INV# pin. A low level

on PD# or PDO# will put the output driver into a high impedance (tri-state) mode. A

weak internal pull-down device brings the output to ground.

DE 46 Out Output Data Enable. This signal qualifies the active data area. A HIGH level signifies

active display time and a LOW level signifies blanking time. This output signal is

synchronized with the output data. A low level on PD# or PDO# will put the output

driver into a high impedance (tri-state) mode. A weak internal pull-down device

brings the output to ground.

HSYNC

VSYNC

CTL1

CTL2

CTL3

Out

Horizontal Sync input control signal.

Vertical Sync input control signal.

General output control signal 1. This output is not powered down by PDO#.

General output control signal 2.

General output control signal 3.

A low level on PD# or PDO# will put the output drivers (except CTL1 by PDO#) into

a high impedance (tri-state) mode. A weak internal pull-down device brings each

output to ground.

SiI 163B PanelLink Receiver

Data Sheet

11 SiI-DS-0055-C

Configuration Pins

Pin Name Pin # Type Description

OCK_INV# 100 In ODCK Polarity. A LOW level selects normal ODCK output. A HIGH level selects

inverted ODCK output. All other output signals are unaffected by this pin. They will

maintain the same timing no matter the setting of OCK_INV# pin

PIXS/M_S 4 In When S_D pin is LOW (Single Link), this pin selects 1-pixel/clock mode (LOW) or 2-

pixel/clock mode (HIGH). When S_D pin is HIGH (Dual Link), this pin is Master

Slave Mode Select.

STAG_OUT#

/SYNC

7 In When S_D pin is LOW (Single Link), this pin selects Staggered Output. A HIGH level

selects normal simultaneous outputs on all odd and even data lines. A LOW level

selects staggered output drive. This function is only available in 2-pixels per clock

mode. When S_D pin is HIGH (Dual Link), this pin is an input pin on the Slave

receiver for the DE signal from the master receiver, used for synchronization.

ST 3 In Output Drive. A HIGH level selects HIGH output drive strength. A LOW level selects

LOW output drive strength.

S_D 1 In Single/Dual Link Mode. A LOW level selects Single Link mode. A HIGH level

selects Dual Link mode. This affects the operation of SYNC, M_S and the two 24-bit

data output buses.

Power Management Pins

Name Pin # Type Description

SCDT 8 Out Sync Detect. A HIGH level is outputted when DE is actively toggling indicating that the

link is alive. A LOW level is outputted when DE is inactive, indicating the link is down.

Can be connected to PDO# to power down the outputs when DE is not detected. The

SCDT output itself, however, remains in the active mode at all times.

PDO# 9 In Output Driver Power Down (active LOW). A HIGH level indicates normal operation. A

LOW level puts all the output drivers only (except SCDT and CTL1) into a high

impedance (tri-state) mode. A weak internal pull-down device brings each output to

ground. PDO# is a sub-set of the PD# description. The chip is not in power-down mode

with this pin. SCDT and CTL1 are not tri-stated by this pin.

PD# 2 In Power Down (active LOW). A HIGH level indicates normal operation. A LOW level

indicates power down mode. During power down mode, all the output drivers are put

into a high impedance (tri-state) mode. A weak internal pull-down device brings each

output to ground. Additionally, all analog logic is powered down, and all inputs are

disabled.

SiI 163B PanelLink Receiver

Data Sheet

12 SiI-DS-0055-C

Differential Signal Data Pins

Pin Name Pin # Type Description

RX0+

RX0-

RX1+

RX1-

RX2+

RX2-

Analog

TMDS Low Voltage Differential Signal input data pairs.

RXC+

RXC-

Analog

TMDS Low Voltage Differential Signal input clock pair.

EXT_RES 96 Analog Impedance Matching Control. An external 390 ohm resistor must be connected

between AVCC and this pin.

Reserved Pin

Pin Name Pin # Type Description

RESERVED 99 In Must be tied HIGH for normal operation.

Power and Ground Pins

Pin Name Pin # Type Description

VCC 6,38,67 Power Digital Core VCC, must be set to 3.3V.

GND 5,39,68 Ground Digital Core GND.

OVCC 18,29,43,57,78 Power Output VCC, must be set to 3.3V.

OGND 19,28,45,58,76 Ground Output GND.

AVCC 82,84,88,95 Power Analog VCC must be set to 3.3V.

AGND 79,83,87,89,92 Ground Analog GND.

PVCC 97 Power PLL Analog VCC must be set to 3.3V.

PGND 98 Ground PLL Analog GND.

SiI 163B PanelLink Receiver

Data Sheet

13 SiI-DS-0055-C

Feature Information

The SiI 163B can be configured in two modes: Single Link and Dual Link. When in Single Link (S_D is LOW), the

device operates in either 1-pixel/clock or 2-pixel/clock mode, according to the state of the PIXS pin. There is no

communication with a second receiver. In this mode, the SiI 163B operates in the same way as the other

PanelLink receivers: SiI 143B, SiI 151B, SiI 153B and SiI 161B.

In Dual Link mode, two SiI 163B’s operate together to handle bandwidths up to 330 megapixels per second. The

configuration and management of this mode is detailed in the following sections. Dual Link mode may operate

across a pixel frequency of 25 MHz to 330 MHz. Below 165 MHz, the second TMDS channel is quiescent. All

pixel data is sent across the first TMDS channel, and handled by the Master SiI 163B receiver. Above 165 MHz,

both SiI 163B receivers are active, with the pixels alternating even-and-odd from Master to Slave, driven by the

two TMDS DVI channels.

Dual Link

Two SiI 163B’s are required for a DVI compatible Dual Link application as configured in the block diagram of

Figure 11. At pixel frequencies up to 165 MHz, the system does not send any data over the second link

connected to the Slave receiver. Therefore, the Slave receiver is not active and its outputs are tri-stated. All the

data, both EVEN and ODD pixels, are sent over the TMDS link connected to the Master receiver. Therefore all the

data, both EVEN and ODD pixels, is output by the Master receiver.

At pixel frequencies above 165 MHz, the system sends EVEN data over the link connected to the Master receiver

and the ODD data over the link connected to the Slave receiver. Therefore, the EVEN data is output by the

Master receiver and the ODD data is output by the Slave receiver. The Master receiver’s ODD data bus is tri-

stated to allow the Slave receiver’s EVEN Data bus to output the ODD data.

Dual Link Configuration Pins

Five pins on the SiI 163B need to be considered for Dual Link receiver applications.

Table 2. SiI 163B Dual Link Pin Definitions

Pin Name Pin # Type Description

S_D 1 In Single/Dual Link Mode. When HIGH, it is in Dual Link Mode. When LOW it is

in Single Link Mode. The Slave receiver is always in Dual Link mode. The

Master receiver switches between Single and Dual Link mode depending

upon the SCDT output of the Slave receiver that is connected to the S_D

input of the Master receiver.

PIXS / M_S 4 In Master/Slave. When S_D pin is HIGH (Dual Link), this pin becomes M_S.

When HIGH, it is in Master mode. When LOW, it is in Slave mode. The

Master receiver is in one/two-pixels per clock mode depending upon

Single/Dual Link operation. The Slave receiver is always in one-pixel per

clock mode.

When S_D is LOW (Single Link), this pin becomes PIXS.

STAG_OUT /

SYNC

7 In Synchronization. When S_D pin is HIGH (Dual Link), this pin is used to

synchronize the Slave receiver to the Master receiver. The SYNC input pin of

the Slave receiver is connected to the DE output pin of the Master receiver.

SCDT 8 Out Sync Detect. When HIGH, there are valid sync signals coming from the

transmitter. When LOW, there are no sync signals coming from the

transmitter. The SCDT pin of the Slave receiver is connected to the S_D pin

of the Master receiver.

DE 46 Out Data Enable. This signal qualifies the active data area. A HIGH level signifies

active display time and a LOW level signifies blanking time. This output signal

is synchronized with the output data.

The DE output pin of the Master is connected to the SYNC input pin of the

Slave.

SiI 163B PanelLink Receiver

Data Sheet

14 SiI-DS-0055-C

163B Master

RX[3:1]

SCDT

SYNC

S_D

M_S

QO[23:0]

QE[23:0]

VSYNC

HSYNC

ODCK

PDO#

RxC+/-

163B Slave

RX[3:1]

SCDT

SYNC

S_D

M_S

QO[23:0]

QE[23:0]

VSYNC

HSYNC

ODCK

PDO#

RxC+/-

VCC

QO[23:0]

QE[23:0]

VSYNC

HSYNC

ODCK

N/C

PDO#

TX1[3:1]

TX2[3:1]

TXC+/-

GND N/C

SCDT

VCC

Figure 11. SiI 163B Dual Link Block Diagram

SiI 163B PanelLink Receiver

Data Sheet

15 SiI-DS-0055-C

Master –

The Master receiver will automatically configure to either Single or Dual Link operation (two or one pixel

per clock mode, respectively) depending on the transmitter system output. This is accomplished by

connecting the SCDT output pin of the Slave to the S_D pin on the Master. When the transmitter sends

data on the second link, the SCDT output of the slave (and the S_D pin on the Master) is driven HIGH,

setting to Dual Link (one-pixel per clock) mode. If there is no data on the second link, the SCDT output of

the Slave (and the S_D pin on the Master) is driven LOW, and the Master receiver is in Single Link (two-

pixels per clock) mode.

The Master receiver is configured by pulling the M_S pin to HIGH. When it is in Dual Link mode, the

Master receiver is in one-pixel per clock mode outputting the EVEN data. The Master receiver’s ODD

data bus is tri-stated to allow the Slave receiver’s EVEN data bus to be used as the ODD data bus. When

it is in Single Link mode, the Master receiver is in two-pixels per clock mode outputting both the EVEN

and ODD data. The Slave receiver’s EVEN data bus is tri-stated to allow the Master receiver’s ODD data

bus to be used as the ODD data.

The DE output pin of the Master receiver is connected to the SYNC input pin of the Slave receiver. This is

used for output synchronization between the Master receiver and Slave receiver. DE, HSYNC, VSYNC,

and ODCK are all connected from the Master receiver.

Slave – The Slave receiver is always configured for Dual Link (one pixel/clock) operation, by tying the S_D pin to

HIGH. The Slave receiver is never used in Single Link mode since the Master receiver is the primary

receiver for Single Link Operation.

The Slave receiver is configured by tying the M_S pin to LOW. The Slave receiver will always contain the

ODD data bus in Dual Link operation. Therefore, it will never be in two-pixels per clock mode.

The SCDT output pin of the Slave receiver is connected to the S_D input pin of the Master receiver to

automatically configure the Master for either Single or Dual Link mode depending upon whether the Slave

receiver is active or not.

The SYNC input pin of the Slave receiver is connected to the DE output pin of the Master receiver for

synchronization.

Since DE, HSYNC, VSYNC, and ODCK are all taken from the Master receiver, these pins are not

connected from the Slave receiver.

Table 3. SiI 163B Dual Link Pin Configuration

S_D PIXS/M_S Master / Slave Description

0 0 Not Used

Single Link One Pixel/Clock Mode. Not supported.

0 1 Master

Single Link Two Pixel/Clock Mode. This is the mode that the Master

receiver will be in when in Single Link mode for pixel clock frequencies

less than or equal to 165MHz.

1 0 Slave

Dual Link Slave (One Pixel/Clock) Mode. This is the mode that the

Slave receiver will always be in for pixel clock frequencies greater

than 165MHz and less than 330MHz.

1 1 Master

Dual Link Master (One Pixel/Clock) Mode. This is the mode that the

Master receiver will be in when in Dual Link mode for pixel clock

frequencies greater than 165MHz and less than 330MHz.

SiI 163B PanelLink Receiver

Data Sheet

16 SiI-DS-0055-C

Dual Link Power Management

Power management with PD# and PDO# is slightly different in a Dual Link design than a Single Link.

When the receivers are in dual-link mode (S_D=1), then the connection from SCDT to PDO# is internal.

A receiver which detects no activity at the TMDS inputs will deassert SCDT, which will then put that chip

into power-down-output mode. This is the process which enables the slave receiver to tri-state its outputs

whenever it stops receiving data.

The outputs may also be directly tri-stated by asserting the PDO# pin.

Receivers will also enter a low-power state when the differential TMDS clock stops. The receiver

awakens when the clock resumes, at which point the receiver begins checking for active data. Active

data will assert SCDT and put the chip back into full-power mode.

Dual Link Mode Selection

Single Link Mode –

In Single Link mode, the Slave receiver is not active. Its outputs are all tri-stated. The Slave receiver will

detect that there is no signal coming from the transmitter and de-assert SCDT to LOW. The SCDT pin

from the Slave receiver is connected to the Master receiver’s S_D pin. This will cause the S_D pin of the

Master receiver to be LOW that will cause the Master receiver to be in Single Link mode. Since the

Master receiver is in Single Link mode, it will output two-pixels per clock. All the Data, both EVEN and

ODD pixels, will be output from the Master receiver. The Slave receiver’s EVEN Data bus is tri-stated to

allow the Master receiver’s ODD Data bus to be used as the ODD Data.

Dual Link Mode –

In Dual Link mode, the Slave receiver is active. The Slave receiver will detect that there are valid signals

coming from the transmitter and assert SCDT to HIGH. This will cause the S_D pin of the Master receiver

to be HIGH that will cause the Master receiver to be in Dual Link mode. This will also cause the Master

receiver to tri-state its Odd Data bus to allow the Slave receiver’s EVEN Data bus to be used as the ODD

Data. The Master receiver will output the EVEN Data. When there are no sync signals coming from the

transmitter, both the Slave and Master receiver’s outputs are tri-stated automatically.

The STAG_OUT pin of the Slave receiver is not used in one-pixel per clock mode, so this takes on a

different meaning in Dual Link mode. It becomes SYNC input pin. This pin is used for synchronization

between the Master and Slave receivers. The DE output pin from the Master receiver is connected to the

SYNC input pin of the Slave receiver.

SiI 163B PanelLink Receiver

Data Sheet

17 SiI-DS-0055-C

Dual Link Timing Diagrams

Below in Figure 12 is an example of the output timing diagram of the Master receiver. When the Slave receiver’s

SCDT signal is LOW, the Slave receiver is inactive and has tri-stated all its data outputs. This is because the

system is sending data with a pixel clock of less than or equal to 165. The DVI link uses the Master receiver only.

There are no signals being sent to the Slave receiver from the system. The Master receiver is in Single Link 2-

pixel/clock mode and outputs the pixel data, both EVEN and ODD pixels.

When the Slave receiver’s SCDT signal goes HIGH, the system is sending sata with a pixel clock greater than

165 MHz and less then 330 MHz. The system is sending the EVEN pixel to the Master receiver and the ODD

pixel to the Slave receiver. The Slave receiver is receiving signals from the system and has asserted its SCDT

signal to the Master receiver. This puts the Master receiver in Dual Link 1-pixel/clock mode. The Slave receiver

outputs the ODD pixel data. The Master receiver outputs the EVEN pixel data. The Master receiver has tri-stated

its ODD pixel bus to allow the Slave receiver to send ODD pixel data.

DE[23:0] DE[23:0]

DO[23:0] DO[23:0]

DE[23:0] DE[23:0] DE[23:0] DE[23:0]

Slave SCDT

(Master S_D)

Master ODCK

Master DO[23:0]

Master DE[23:0]

DO[23:0] of the Master is Tri-Stated to let the Slave's DE[23:0]

become the ODD pixel data for the Panel.

2-pixels/clock 1-pixel/clock

Figure 12. Timing Diagram of Master's Output

SiI 163B PanelLink Receiver

Data Sheet

18 SiI-DS-0055-C

Figure 13 is an example of the output timing diagram of the Slave receiver. When the Slave receiver’s SCDT

signal is LOW, the Slave receiver is inactive and has tri-stated all its outputs. This is because the system is

sending data with a pixel clock of less than or equal to 165 MHz on the link connected to the Master receiver only.

There are no signals being sent to the Slave receiver from the system.

When the Slave receiver’s SCDT signal goes HIGH, the system is sending data with a pixel clock greater than

165 MHz and less than 330 MHz. The system is sending the EVEN pixel to the Master receiver and the ODD

pixel to the Slave receiver. The Slave receiver is receiving signals from the system and has asserted its SCDT

signal to the Master receiver. This puts the Master receiver in Dual Link 1-pixel/clock mode. The Slave receiver is

outputting the ODD pixel data on its EVEN pixel bus. The Master receiver outputs the EVEN pixels. The Master

receiver has tri-stated its ODD pixel bus to allow the Slave receiver to send ODD pixel data.

DE[23:0] DE[23:0] DE[23:0] DE[23:0]

Slave SCDT

(Master S_D)

Master ODCK

Slave DO[23:0]

Slave DE[23:0]

Slave is receiving Data from the System and

outputs it on DE[23:0]. DO[23:0] is kept Tri-Stated.

Slave is not receiving

Data from the System

and Tri-States its Data

bus and Clock.

1-pixel/clock

Figure 13. Timing Diagram of Slave's Output

Figure 14 is an example of the data that is driven out by the two receivers. All the control signals, including

ODCK, are sent by the Master receiver.

DE[23:0] DE[23:0]

DO[23:0] DO[23:0]

DE[23:0] DE[23:0]

DO[23:0] DO[23:0]

DE[23:0] DE[23:0]

DO[23:0] DO[23:0]

Slave SCDT

(Master S_D)

Master ODCK

(2-pixel/clock

Mode)

Panel DO[23:0]

Panel DE[23:0]

Slave is not Active.

Outputs are Tri-Stated

Master is in Single Link

Two-Pixels/Clock Mode.

Master is outputting

both Even and Odd

pixels.

Master is in Dual Link One-Pixel/Clock Mode.

Master is outputting Even pixels. Master has Tri-

Stated its Odd pixel bus to allow Slave to output

Odd pixel data.

Slave is in Dual Link One-Pixel/Clock Mode.

Slave is outputing Odd pixels.

System is sending Data

only to the Master. Only

clock is sent to the

Slave.

System is sending the Even pixel data to the

Master and the Odd pixel data to the Slave.

Figure 14. Single/Dual Link Timing Diagram

SiI 163B PanelLink Receiver

Data Sheet

19 SiI-DS-0055-C

Table 4. DVI-D Connector to SiI 163B for Dual Link Application Pin Connection

DVI-D Connector SiI 163B - Master SiI 163B - Slave

Pin # Signal Pin # Pin Name Pin # Pin Name

1 TMDS Data2- 81 Rx2- for Master

2 TMDS Data2+ 80 Rx2+ for Master

3 TMDS Data2/4 Shield

4 TMDS Data4- 86 Rx1- for Slave

5 TMDS Data4+ 85 Rx1+ for Slave

6 DDC Clock

7 DDC Data

8 NC

9 TMDS Data1- 86 Rx1- for Master

10 TMDS Data1+ 85 Rx1+ for Master

11 TMDS Data1/3 Shield

12 TMDS Data3- 91 Rx0- for Slave

13 TMDS Data3+ 90 Rx0+ for Slave

14 +5V Power

15 Ground

16 Hot Plug Detect

17 TMDS Data0- 91 Rx0- for Master

18 TMDS Data0+ 90 Rx0+ for Master

19 TMDS Data0/5 Shield

20 TMDS Data5- 81 Rx2- for Slave

21 TMDS Data5+ 80 Rx2+ for Slave

22 TMDS Clock Shield

23 TMDS Clock+ 93 RxC+ for Master 93 RxC+ for Slave

24 TMDS Clock- 94 RxC- for Master 94 RxC- for Slave

Clock Detect Function

The SiI 163B includes a new power saving feature: power down with clock detect circuit. The SiI 163B will go into

a low power mode when there is no video clock coming from the transmitter. In this mode, the entire chip is

powered down except the clock detect circuitry. During this mode, digital I/O are set to a high impedance (tri-

state) mode. A weak internal pull-down device brings each output to ground. The device power down and wake-

up times are shown in Figure 6 and Figure 7.

OCK_INV# Function

OCK_INV# affects only the phase of the clock output as

indicated in Figure 15. OCK_INV# does not change the

timing for the internal data latching. This timing is

shown in Figure 5.

QE[23:0]

QO[23:0]

ODCK

OCK_INV#

Figure 15. Block Diagram for OCK_INV#

SiI 163B PanelLink Receiver

Data Sheet

20 SiI-DS-0055-C

TFT Panel Data Mapping

Table 5 summarizes the output data mapping in one pixel per clock mode for the SiI 163B. This output data

mapping is dependent upon the PanelLink transmitters having the exact same type of input data mappings.

Table 6 summarizes the output data mapping in two pixel per clock mode. More detailed mapping information is

found on the following pages. Refer to application note SiI-AN-0007 for DSTN applications.

Note that the choice of one pixel/clock versus two pixel/clock on the transmitter side has no effect on the choice of

one pixel/clock versus two pixel/clock on the receiver side. The data is always sent across the link at the pixel

clock rate. Therefore, designers using PanelLink receivers do not need to know how the transmitter has taken in

pixel data on the transmitter input pins.

Table 5. One Pixel/Clock Mode Data Mapping

SiI 163B

DATA

1-Pixel/Clock Output

18bpp 24bpp

BLUE[7:0] QE[7:2] QE[7:0]

GREEN[7:0] QE[15:10] QE[15:8]

RED[7:0] QE[23:18] QE[23:16]

Table 6. Two Pixel/Clock Mode Data Mapping

SiI 163B

DATA

2-Pixel/Clock Output

18bpp 24bpp

BLUE[7:0] – 0 QE[7:2] QE[7:0]

GREEN[7:0] – 0 QE[15:10] QE[15:8]

RED[7:0] – 0 QE[23:18] QE[23:16]

BLUE[7:0] – 1 QO[7:2] QO[7:0]

GREEN[7:0] – 1 QO[15:10] QO[15:8]

RED[7:0] – 1 QO[23:18] QO[23:16]

SiI 163B PanelLink Receiver

Data Sheet

21 SiI-DS-0055-C

Note: SiI143B, SiI151B, SiI153B and SiI 161B all have the same pinout. The pin assignments shown in the

following tables should also be used for these other receivers.

Table 7. One Pixel/Clock Input/Output TFT Mode – VESA P&D and FPDI-2TM Compliant

TFT VGA Output Tx Input Data Rx Output Data TFT Panel Input

24-bpp 18-bpp 160 164 163B 141B 24-bpp 18-bpp

B0 DIE0 D0 QE0 Q0 B0

B1 DIE1 D1 QE1 Q1 B1

B2 B0 DIE2 D2 QE2 Q2 B2 B0

B3 B1 DIE3 D3 QE3 Q3 B3 B1

B4 B2 DIE4 D4 QE4 Q4 B4 B2

B5 B3 DIE5 D5 QE5 Q5 B5 B3

B6 B4 DIE6 D6 QE6 Q6 B6 B4

B7 B5 DIE7 D7 QE7 Q7 B7 B5

G0 DIE8 D8 QE8 Q8 G0

G1 DIE9 D9 QE9 Q9 G1

G2 G0 DIE10 D10 QE10 Q10 G2 G0

G3 G1 DIE11 D11 QE11 Q11 G3 G1

G4 G2 DIE12 D12 QE12 Q12 G4 G2

G5 G3 DIE13 D13 QE13 Q13 G5 G3

G6 G4 DIE14 D14 QE14 Q14 G6 G4

G7 G5 DIE15 D15 QE15 Q15 G7 G5

R0 DIE16 D16 QE16 Q16 R0

R1 DIE17 D17 QE17 Q17 R1

R2 R0 DIE18 D18 QE18 Q18 R2 R0

R3 R1 DIE19 D19 QE19 Q19 R3 R1

R4 R2 DIE20 D20 QE20 Q20 R4 R2

R5 R3 DIE21 D21 QE21 Q21 R5 R3

R6 R4 DIE22 D22 QE22 Q22 R6 R4

R7 R5 DIE23 D23 QE23 Q23 R7 R5

Shift

CLK

Shift

CLK

IDCK IDCK ODCK ODCK Shift

CLK

Shift

CLK

VSYNC VSYNC VSYNC VSYNC VSYNC VSYNC VSYNC VSYNC

HSYNC HSYNC HSYNC HSYNC HSYNC HSYNC HSYNC HSYNC

DE DE DE DE DE DE DE DE

For 18-bit mode, the Flat Panel Graphics Controller interfaces to the Transmitter exactly the same as in the 24-bit

mode; however, 6 bits per channel (color) are used instead of 8. It is recommended that unused data bits be tied

low. As can be seen from the above table, the data mapping for less than 24-bit per pixel interfaces are MSB

justified. The data is sent during active display time while the control signals are sent during blank time. Note that

the three data channels (CH0, CH1, CH2) are mapped to Blue, Green and Red data respectively.

SiI 163B PanelLink Receiver

Data Sheet

22 SiI-DS-0055-C

Table 8. Two Pixels/Clock Input/Output TFT Mode

TFT VGA Output Tx Input Data Rx Output Data TFT Panel Input

24-bpp 18-bpp 160 163B 24-bpp 18-bpp

B0 – 0 DIE0 QE0 B0 – 0

B1 – 0 DIE1 QE1 B1 – 0

B2 – 0 B0 – 0 DIE2 QE2 B2 – 0 B0 – 0

B3 – 0 B1 – 0 DIE3 QE3 B3 – 0 B1 – 0

B4 – 0 B2 – 0 DIE4 QE4 B4 – 0 B2 – 0

B5 – 0 B3 – 0 DIE5 QE5 B5 – 0 B3 – 0

B6 – 0 B4 – 0 DIE6 QE6 B6 – 0 B4 – 0

B7 – 0 B5 – 0 DIE7 QE7 B7 – 0 B5 – 0

G0 – 0 DIE8 QE8 G0 – 0

G1 – 0 DIE9 QE9 G1 – 0

G2 – 0 G0 – 0 DIE10 QE10 G2 – 0 G0 – 0

G3 – 0 G1 – 0 DIE11 QE11 G3 – 0 G1 – 0

G4 – 0 G2 – 0 DIE12 QE12 G4 – 0 G2 – 0

G5 – 0 G3 – 0 DIE13 QE13 G5 – 0 G3 – 0

G6 – 0 G4 – 0 DIE14 QE14 G6 – 0 G4 – 0

G7 – 0 G5 – 0 DIE15 QE15 G7 – 0 G5 – 0

R0 – 0 DIE16 QE16 R0 – 0

R1 – 0 DIE17 QE17 R1 – 0

R2 – 0 R0 – 0 DIE18 QE18 R2 – 0 R0 – 0

R3 – 0 R1 – 0 DIE19 QE19 R3 – 0 R1 – 0

R4 – 0 R2 – 0 DIE20 QE20 R4 – 0 R2 – 0

R5 – 0 R3 – 0 DIE21 QE21 R5 – 0 R3 – 0

R6 – 0 R4 – 0 DIE22 QE22 R6 – 0 R4 – 0

R7 – 0 R5 – 0 DIE23 QE23 R7 – 0 R5 – 0

B0 – 1 DIO0 QO0 B0 – 1

B1 – 1 DIO1 QO1 B1 – 1

B2 – 1 B0 – 1 DIO2 QO2 B2 – 1 B0 – 1

B3 – 1 B1 – 1 DIO3 QO3 B3 – 1 B1 – 1

B4 – 1 B2 – 1 DIO4 QO4 B4 – 1 B2 – 1

B5 – 1 B3 – 1 DIO5 QO5 B5 – 1 B3 – 1

B6 – 1 B4 – 1 DIO6 QO6 B6 – 1 B4 – 1

B7 – 1 B5 – 1 DIO7 QO7 B7 – 1 B5 – 1

G0 – 1 DIO8 QO8 G0 – 1

G1 – 1 DIO9 QO9 G1 – 1

G2 – 1 G0 – 1 DIO10 QO10 G2 – 1 G0 – 1

G3 – 1 G1 – 1 DIO11 QO11 G3 – 1 G1 – 1

G4 – 1 G2 – 1 DIO12 QO12 G4 – 1 G2 – 1

G5 – 1 G3 – 1 DIO13 QO13 G5 – 1 G3 – 1

G6 – 1 G4 – 1 DIO14 QO14 G6 – 1 G4 – 1

G7 – 1 G5 – 1 DIO15 QO15 G7 – 1 G5 – 1

R0 – 1 DIO16 QO16 R0 – 1

R1 – 1 DIO17 QO17 R1 – 1

R2 – 1 R0 – 1 DIO18 QO18 R2 – 1 R0 – 1

R3 – 1 R1 – 1 DIO19 QO19 R3 – 1 R1 – 1

R4 – 1 R2 – 1 DIO20 QO20 R4 – 1 R2 – 1

R5 – 1 R3 – 1 DIO21 QO21 R5 – 1 R3 – 1

R6 – 1 R4 – 1 DIO22 QO22 R6 – 1 R4 – 1

R7 – 1 R5 – 1 DIO23 QO23 R7 – 1 R5 – 1

ShiftClk/2 ShiftClk/2 IDCK ODCK Shift CLK Shift CLK

VSYNC VSYNC VSYNC VSYNC VSYNC VSYNC

HSYNC HSYNC HSYNC HSYNC HSYNC HSYNC

DE DE DE DE DE DE

SiI 163B PanelLink Receiver

Data Sheet

23 SiI-DS-0055-C

Table 9. 24-bit One Pixel/Clock Input with 24-bit Two Pixels/Clock Output TFT Mode

TFT VGA Output Tx Input Data Rx Output Data TFT Panel Input

24-bpp 160 164 163B 24-bpp

B0 DIE0 D0 QE0 B0 – 0

B1 DIE1 D1 QE1 B1 – 0

B2 DIE2 D2 QE2 B2 – 0

B3 DIE3 D3 QE3 B3 – 0

B4 DIE4 D4 QE4 B4 – 0

B5 DIE5 D5 QE5 B5 – 0

B6 DIE6 D6 QE6 B6 – 0

B7 DIE7 D7 QE7 B7 – 0

G0 DIE8 D8 QE8 G0 – 0

G1 DIE9 D9 QE9 G1 – 0

G2 DIE10 D10 QE10 G2 – 0

G3 DIE11 D11 QE11 G3 – 0

G4 DIE12 D12 QE12 G4 – 0

G5 DIE13 D13 QE13 G5 – 0

G6 DIE14 D14 QE14 G6 – 0

G7 DIE15 D15 QE15 G7 – 0

R0 DIE16 D16 QE16 R0 – 0

R1 DIE17 D17 QE17 R1 – 0

R2 DIE18 D18 QE18 R2 – 0

R3 DIE19 D19 QE19 R3 – 0

R4 DIE20 D20 QE20 R4 – 0

R5 DIE21 D21 QE21 R5 – 0

R6 DIE22 D22 QE22 R6 – 0

R7 DIE23 D23 QE23 R7 – 0

QO0 B0 – 1

QO1 B1 – 1

QO2 B2 – 1

QO3 B3 – 1

QO4 B4 – 1

QO5 B5 – 1

QO6 B6 – 1

QO7 B7 – 1

QO8 G0 – 1

QO9 G1 – 1

QO10 G2 – 1

QO11 G3 – 1

QO12 G4 – 1

QO13 G5 – 1

QO14 G6 – 1

QO15 G7 – 1

QO16 R0 – 1

QO17 R1 – 1

QO18 R2 – 1

QO19 R3 – 1

QO20 R4 – 1

QO21 R5 – 1

QO22 R6 – 1

QO23 R7 – 1

Shift CLK IDCK IDCK ODCK Shift CLK/2

VSYNC VSYNC VSYNC VSYNC VSYNC

HSYNC HSYNC HSYNC HSYNC HSYNC

DE DE DE DE DE

SiI 163B PanelLink Receiver

Data Sheet

24 SiI-DS-0055-C

Table 10. 18-bit One Pixel/Clock Input with 18-bit Two Pixels/Clock Output TFT Mode

TFT VGA Output Tx Input Data Tx Output Data TFT Panel Input

18-bpp 160 164 163B 141B 18-bpp

DIE0 D0 QE0

DIE1 D1 QE1

B0 DIE2 D2 QE2 Q0 B0 – 0

B1 DIE3 D3 QE3 Q1 B1 – 0

B2 DIE4 D4 QE4 Q2 B2 – 0

B3 DIE5 D5 QE5 Q3 B3 – 0

B4 DIE6 D6 QE6 Q4 B4 – 0

B5 DIE7 D7 QE7 Q5 B5 – 0

DIE8 D8 QE8

DIE9 D9 QE9

G0 DIE10 D10 QE10 Q6 G0 – 0

G1 DIE11 D11 QE11 Q7 G1 – 0

G2 DIE12 D12 QE12 Q8 G2 – 0

G3 DIE13 D13 QE13 Q9 G3 – 0

G4 DIE14 D14 QE14 Q10 G4 – 0

G5 DIE15 D15 QE15 Q11 G5 – 0

DIE16 D16 QE16

DIE17 D17 QE17

R0 DIE18 D18 QE18 Q12 R0 – 0

R1 DIE19 D19 QE19 Q13 R1 – 0

R2 DIE20 D20 QE20 Q14 R2 – 0

R3 DIE21 D21 QE21 Q15 R3 – 0

R4 DIE22 D22 QE22 Q16 R4 – 0

R5 DIE23 D23 QE23 Q17 R5 – 0

QO0

QO1

QO2 Q18 B0 – 1

QO3 Q19 B1 – 1

QO4 Q20 B2 – 1

QO5 Q21 B3 – 1

QO6 Q22 B4 – 1

QO7 Q23 B5 – 1

QO8

QO9

QO10 Q24 G0 – 1

QO11 Q25 G1 – 1

QO12 Q26 G2 – 1

QO13 Q27 G3 – 1

QO14 Q28 G4 – 1

QO15 Q29 G5 – 1

QO16

QO17

QO18 Q30 R0 – 1

QO19 Q31 R1 – 1

QO20 Q32 R2 – 1

QO21 Q33 R3 – 1

QO22 Q34 R4 – 1

QO23 Q35 R5 – 1

Shift CLK IDCK IDCK ODCK Shift CLK/2 Shift CLK/2

VSYNC VSYNC VSYNC VSYNC VSYNC VSYNC

HSYNC HSYNC HSYNC HSYNC HSYNC HSYNC

DE DE DE DE DE DE

SiI 163B PanelLink Receiver

Data Sheet

25 SiI-DS-0055-C

Table 11. Two Pixels/Clock Input with One Pixel/Clock Output TFT Mode

TFT VGA Output Tx Input Data Rx Output Data TFT Panel Input

24-bpp 18-bpp 160 163B 141B 24-bpp 18-bpp

B0 – 0 DIE0 QE0 Q0 B0

B1 – 0 DIE1 QE1 Q1 B1

B2 – 0 B0 – 0 DIE2 QE2 Q2 B2 B0

B3 – 0 B1 – 0 DIE3 QE3 Q3 B3 B1

B4 – 0 B2 – 0 DIE4 QE4 Q4 B4 B2

B5 – 0 B3 – 0 DIE5 QE5 Q5 B5 B3

B6 – 0 B4 – 0 DIE6 QE6 Q6 B6 B4

B7 – 0 B5 – 0 DIE7 QE7 Q7 B7 B5

G0 – 0 DIE8 QE8 Q8 G0

G1 – 0 DIE9 QE9 Q9 G1

G2 – 0 G0 – 0 DIE10 QE10 Q10 G2 G0

G3 – 0 G1 – 0 DIE11 QE11 Q11 G3 G1

G4 – 0 G2 – 0 DIE12 QE12 Q12 G4 G2

G5 – 0 G3 – 0 DIE13 QE13 Q13 G5 G3

G6 – 0 G4 – 0 DIE14 QE14 Q14 G6 G4

G7 – 0 G5 – 0 DIE15 QE15 Q15 G7 G5

R0 – 0 DIE16 QE16 Q16 R0

R1 – 0 DIE17 QE17 Q17 R1

R2 – 0 R0 – 0 DIE18 QE18 Q18 R2 R0

R3 – 0 R1 – 0 DIE19 QE19 Q19 R3 R1

R4 – 0 R2 – 0 DIE20 QE20 Q20 R4 R2

R5 – 0 R3 – 0 DIE21 QE21 Q21 R5 R3

R6 – 0 R4 – 0 DIE22 QE22 Q22 R6 R4

R7 – 0 R5 – 0 DIE23 QE23 Q23 R7 R5

B0 – 1 DIO0

B1 – 1 DIO1

B2 – 1 B0 – 1 DIO2

B3 – 1 B1 – 1 DIO3

B4 – 1 B2 – 1 DIO4

B5 – 1 B3 – 1 DIO5

B6 – 1 B4 – 1 DIO6

B7 – 1 B5 – 1 DIO7

G0 – 1 DIO8

G1 – 1 DIO9

G2 – 1 G0 – 1 DIO10

G3 – 1 G1 – 1 DIO11

G4 – 1 G2 – 1 DIO12

G5 – 1 G3 – 1 DIO13

G6 – 1 G4 – 1 DIO14

G7 – 1 G5 – 1 DIO15

R0 – 1 DIO16

R1 – 1 DIO17

R2 – 1 R0 – 1 DIO18

R3 – 1 R1 – 1 DIO19

R4 – 1 R2 – 1 DIO20

R5 – 1 R3 – 1 DIO21

R6 – 1 R4 – 1 DIO22

R7 – 1 R5 – 1 DIO23

ShiftClk/2 ShiftClk/2 IDCK ODCK ODCK ShiftClk ShiftClk

VSYNC VSYNC VSYNC VSYNC VSYNC VSYNC VSYNC

HSYNC HSYNC HSYNC HSYNC HSYNC HSYNC HSYNC

DE DE DE DE DE DE DE

SiI 163B PanelLink Receiver

Data Sheet

26 SiI-DS-0055-C

Table 12. Output Clock Configuration by Ty pical Application

DF0 PIX OCK_INV# PANEL ODCK (frequency /data latch edge/mode)

0 0 0 TFT/16-bit DSTN divide by 1 / negative / free running

0 0 1 TFT/16-bit DSTN divide by 1 / positive / free running

0 1 0 TFT divide by 2 / negative / free running

0 1 1 TFT divide by 2 /positive / free running

1 0 0 24-bit DSTN divide by 1 / negative / blanked low

1 0 1 NONE divide by 1 / negative / blanked high

1 1 0 24-bit DSTN divide by 2 / negative / blanked low

1 1 1 24-bit DSTN divide by 4 / negative / blanked low

Note: DF0 is a signal available only on the SiI141B receiver. DSTN panels may be supported with the SiI 163B

by running the extra blanked clock through an unused data pin. This works only at one pixel per clock mode, and

only when the 24 data bits are not already used for pixel data. Such a solution also requires that the transmitter

board design input the shift clock (the blanked clock for DSTN) into the same unused data pin. By using the

SiI141B, DSTN panels may be driven without requiring any special connections on the transmitter side.

SiI 163B PanelLink Receiver

Data Sheet

27 SiI-DS-0055-C

Design Recommendations

The following sections describe recommendations for robust board design with this PanelLink receiver.

Designers should include provision for these circuits in their design, and adjust the specific passive component

values according to the characterization results.

Differences Between SiI 161A and SiI 163B

While the SiI 163B is pin to pin compatible with the SiI 161A, there are minor differences in functions and

suggested external component value. When designing the SiI 163B into an existing design, note that the

recommended external resistor (EXT_RES) value has changed from 560 ohms to 390 ohms to match the

impedance of a 50 ohm cable.

Table 13 lists the differences between SiI 161A and SiI 163B. Table 14 lists SiI 161B to SiI 163B differences.

Table 13. SiI 161A vs. SiI 163B Pin Differences

Pin/Function SiI 161A SiI 163B

EXT_RES Resistor Value 560 ohm 390 ohm

SCDT When PDO# is asserted, a pull-up resistor is

needed on SCDT to assure high-level.

SCDT continues to drive high or low when

PDO# is asserted. No need for pull-up.

HSYNC, VSYNC, CTL[1..3] Dejitter circuit adds one pixel clock time to

time from DE fall to first edge of these

signals. This affects front-porch time for

HSYNC and VSYNC.

Dejitter circuit is always disabled.

Improved Output Drive

Strength

Refer to SiI 161A Data Sheet for specifics. Output drive strength improved for these

signals. Refer to DC Specifications on

page 4. This improves output waveforms

when driving multiple loads. Some

designs may be able to change from ST=1

to ST=0.

Clock Detect for Lower

Standby Power.

Receiver powers down when PDO# is

asserted. SCDT asserts only when the chip

detects the lack of DE pulses.

Receiver detects when the differential

input clock has stopped and powers down

the internals of the chip. Refer to ICLKI in

DC Specifications on page 4.

PDO# Low-Power Mode

Improved

PDO# assertion powers down most of the

chip.

Improved design powers down more

active circuitry, resulting in lower power

when PDO# is asserted.

Differential Input Capacitance

Reduced

Improved DVI signal reception from SiI

161A .

PD#, PDO#, STAG_OUT#,

OCK_INV#

Pins were named: PD, PDO, STAG_OUT

and OCK_INV.

No functional change was made. Names

were changed to clarify their “active low”

sense.

Table 14. SiI 161B vs. SiI 163B Pin Differences

Pin/Function SiI 161B SiI 163B

PDO# Low-Power Mode

Improved

PDO# assertion powers down most of the

chip.

In dual-link mode, the SCDT to PDO#

connection is also internal and automatic.

See Dual Link Power Management on

page 16.

HSYNC, VSYNC, CTL[1:3] Dejitter circuit improved over SiI 161A. The

DE-low to first-edge time for these signals is

identical to the timing input to the

transmitter. Dejitter circuit may be enabled

or disabled using a pin.

Dejitter circuit is always disabled. There is

no package pin to control this feature.

SiI 163B PanelLink Receiver

Data Sheet

28 SiI-DS-0055-C

Voltage Ripple Regulation

The power supply to VCC pins is very important to the proper operation of the receiver chips. Two examples of

regulators are shown in Figure 16 and Figure 17.

1K ohms

3K ohms

Vin=5V Vout=3.3V

TL431

Figure 16. Volt age Regulation using TL431

Decoupling and bypass capacitors are also involved with power supply connections, as described in detail in

Figure 19.

240 ohms

390 ohms

Vin=5V

Vout=3.3V

ADJ

Vin Vout

LM317EMP

Figure 17. Volt age Regulation using LM317

SiI 163B PanelLink Receiver

Data Sheet

29 SiI-DS-0055-C

Decoupling Capacitors

Designers should include decoupling and bypass capacitors at each power pin in the layout. These are shown

schematically in Figure 19. Place these components as closely as possible to the PanelLink device pins, and

avoid routing through vias if possible, as shown in Figure 18, which is representative of the various types of power

pins on the receiver.

VCC

Ferrite

Preferable

Via to GND

VCC

GND

Figure 18. Decoupling and Bypass Capacitor Placement

VCCPIN

C1 C2

VCC

Figure 19. Decoupling and Bypass Schematic

Table 15. Recommended Components

C1 C2 C3 L1

100 – 300 pF 2.2 – 10 uF 10 uF 200+ ohms

The values shown in Table 15 are recommendations that should be adjusted according to the noise

characteristics of the specific board-level design. Pins in one group (such as OVCC) may share L1 and C3, each

pin having C1 placed as closely to the pin as possible.

SiI 163B PanelLink Receiver

Data Sheet

30 SiI-DS-0055-C

Series Damping Resistors on Outputs

Series resistors are effective in lowering the data-related emissions and reducing reflections. Series resistors

should be placed close to the output pins on the receiver chip, as shown in Figure 20.

Figure 20. Receiver Output Series Damping Resistors

Receiver Layout

Figure 21 to Figure 23 show an example routing of Dual Link for a DVI connector to the two SiI 163B’s. The

differential clock lines must be routed to the Slave receiver first, then to the Master receiver because of the way

the internal impedance matching circuit is configured.

Rx2+

Rx2-

Rx1+

Rx1-

Rx0+

Rx0-

RxC

RxC-

Rx2+

Rx2-

Rx1+

Rx1-

Rx0+

Rx0-

RxC

RxC-

Slave Master

Figure 21. DVI Dual Link Rx PCB Routing Example – Top View

When operating as a Dual Link system, the two SiI 163B’s must output their two data buses with synchronous

timing. As described earlier, this is done by connecting DE from the Master to SYNC on the Slave. The length of

the routed net from Master to Slave must be controlled to between 2.5 and 3.5 inches long. (This corresponds to

a flight time of 400ps to 560ps, at a propagation velocity of 160ps per inch, typical of PCB layouts.)

Similarly, the connection to the differential clock, at Slave and Master, must use routed nets which are controlled

in length. The ‘stub’ from the differential pair to the Slave RxC+ and RxC- pins must be less than 1.0 inch long

(160ps). The differential pair from the start of a the Slave’s ‘stub’ to the Master’s RxC+ and RxC- pins must be no

longer than 3 inches long (~500ps). Pull down resistors to stabilize Slave SCDT output(shown on Figure 24) can

be placed further from the Slave TMDS traces.

Differential routing or DE-to-SYNC routing longer than these limits will create a skew between Master and Slave

which may exceed what can be corrected in the receivers’ logic.

SiI 163B PanelLink Receiver

Data Sheet

31 SiI-DS-0055-C

Rx2+

Rx2-

Rx1+

Rx1-

Rx0+

Rx0-

RxC

RxC-

Rx2+

Rx2-

Rx1+

Rx1-

Rx0+

Rx0-

RxC

RxC-

Slave Master

Figure 22. DVI Dual Link Rx PCB Routing Example – Top Signals Top View

Rx2+

Rx2-

Rx1+

Rx1-

Rx0+

Rx0-

RxC

RxC-

Rx2+

Rx2-

Rx1+

Rx1-

Rx0+

Rx0-

RxC

RxC-

1724

Slave Master

Figure 23. DVI Dual Link Rx PCB Routing Example - Bottom Signals Top View

The receiver chip should be placed as closely as possible to the input connector which carries the TMDS signals.

For a system using the industry-standard DVI connector (see http://www.ddwg.org), the differential lines should

be routed as directly as possible from connector to receiver. PanelLink devices are tolerant of skews between

differential pairs, so spiral skew compensation for path length differences is not required. Each differential pair

should be routed together, minimizing the number of vias through which the signal lines are routed.

As defined in the DVI 1.0 Specification, the impedance of the traces between the connector and the receiver

should be 100 ohms differentially, and close to 50 ohms single-ended. The 100 ohm requirement is to best match

the differential impedance of the cable and connectors, to prevent reflections. The common mode currents are

very small on the TMDS interface, so differential impedance is more important than single-ended.

SiI 163B PanelLink Receiver

Data Sheet

32 SiI-DS-0055-C

Stabilized TMDS Inputs

The SCDT output of the slave SiI 163B receiver indicates the presence (or absence) of display data on the TMDS

link. Both incoming TMDS clock and data will output a HIGH via SCDT indicating that the encoded DE signal and

Clock from the TMDS transmitter is being detected and the link is active. In Dual Link mode the input Clock

signal is shared between Master and Slave SiI 163B.

When functioning in Single Link (in a Dual Link application), input TMDS data for Slave SiI 163B is absent, SCDT

output of the Slave SiI 163B will go low. However, system noise or coupled noise (above 20mV) can trigger the

differential input circuits of the receiver falsely indicating that display data is being received. In this condition, the

SiI 163B can assert SCDT High, even though the input data is invalid.

The SCDT output can be stabilized by introducing an offset voltage at the differential inputs. This can be

achieved by adding pull down resistors to the appropriate inputs. A nominal value of 2K ohms provides sufficient

offset between the + and – data differential inputs. In the application circuit, any value between 1.8K ohms and

2.5K ohms can be used with minimal effect on the single ended impedance.

Slave SiI 163B

RX2+

RX2-

RX1+

RX1-

RX0+

RX0-

RXC+

RXC-

~2K

Three pull down resistors should be placed

on either the + or – differential data input

pins. Figure 24 illustrates each + differential

input data pin pulled down by a nominal 2K

ohm resistor. The pull down resistors can be

placed either close to the receiver or the DVI

connector based on layout efficiency. Ensure

that the trace leading to the resistor and

ground is as short as possible to reduce

capacitive loading. The TMDS Clock (RXC+

and RXC–) input pins do not require pull

down resistors since they have internal pull

down resistors.

Figure 24. Stabilizing SCDT

Staggered Outputs and Two Pixels per Clock

PanelLink receivers offer two features that can minimize the switching effects of the high-speed output data bus:

two pixels per clock mode and staggered outputs.

The receiver can output one or two pixels in each output clock cycle. By widening the bus to two pixels per clock

whenever possible, the clock speed is halved and the switching period of the data signals themselves is twice as

long as in one pixel per clock mode. Typically, SXGA-resolution and above LCD panels expect to be connected

with a 36-bit or 48-bit bus, two pixels per clock. Most XGA-resolution and below LCD panels use an 18- to 24-bit

one pixel per clock interface.

When in two pixel per clock mode, the STAG_OUT# pin on receivers provides an additional means of reducing

simultaneous switching activity. When enabled (STAG_OUT# = Low), only half of the output data pins switch

together. The other half are switched one quarter clock cycle later. Note that both pixel buses use the same

clock. Therefore, the staggered bus will have one quarter clock cycle less setup time to the clock, and one

quarter clock cycle more hold time. Board designers driving into another clocked chip should take this into

account in their timing analysis.

Silicon Image recommends the use of STAG_OUT# and the two pixel per clock mode whenever possible.

Note that these features are limited when the SiI 163B is connected in Dual Link configuration.

SiI 163B PanelLink Receiver

Data Sheet

33 SiI-DS-0055-C

Packaging

ePad Enhancement

The SiI163B is packaged in a 100-pin TQFP package with ePad. The ePad dimensions are shown in Figure 25.

Drawing is not to sc ale.

View from bottom of package.

Pin #1

Pin 2

typ max

T1 ePad Height 6.5

T2 ePad Width 6.5

tw ePad extension Width 0.3 0.4

th ePad extension Length 0.7 1.0

∆T Tolerance +0.1

All dimensions are in millimeters.

ePad is centered on the package center lines with the tolerance shown.

Figure 25. ePad Diagram

The ePad must not be electrically connected to any other voltage level except ground (GND). A clearance of at

least 0.25mm should be designed on the PCB between the edge of the ePad and the inner edges of the lead

pads to avoid any electrical shorts. Dimensions T1 and T2 define the maximum limit of ePad size. Protrusions

from the edges of the ePad may vary slightly from one package assembler to another, but all are confined to

within these maximum dimensions.

SiI 163B PanelLink Receiver

Data Sheet

34 SiI-DS-0055-C

PCB Thermal Land Area

The thermal land area on the PCB may use thermal vias to improve heat removal from the package. These

thermal vias can double as ground connections, attaching internally in the PCB to the ground plane. An array of

vias should be designed into the PCB beneath the package. For optimum thermal performance, it is

recommended that the via diameter should be 12 to 13 mils (0.30 to 0.33mm) and the via barrel should be plated

with 1 ounce copper to plug the via. This is desirable to avoid any solder wicking inside the via during the

soldering process, which may result in voids in solder between the exposed pad and the thermal land. If the

copper plating does not plug the vias, the thermal vias can be ‘tented’ with solder mask on the top surface of the

PCB to avoid solder wicking inside the via during assembly. The solder mask diameter should be at least 4 mils

(0.1mm) larger than the via diameter.

Package stand-off is also a consideration. For a nominal stand-off of 0.1mm (see Figure 27, dimension ‘A1’), the

stencil thickness of 5 to 8 mils should provide a good solder joint between the ePad and the thermal land. The

aperture opening should be subdivided into an array of smaller openings.

Thermal Via

1.0mm0.2mm

0.2mm

1.0mm

Ø 0.3mm

Thermal

Land

Land pattern according

to IPC-SM-782.

Figure 26. ePad Template Layout

For improved heat transfer, the exposed ePad should be soldered to the thermal land on the PCB. This requires

solder paste application not only on the pin pad pattern, but also on the thermal land using a stencil. The stencil

thickness is a function of the lead pitch, package coplanarity and stencil dimensions. For a nominal package

standoff of 0.1mm, a stencil with 5 to 8 mil thickness should provide a good solder joint between the ePad and the

thermal land.

The thermal land is covered with a passivation layer, with openings corresponding to each of the metal

rectangles. For improved solder release, the land area should be subdivided into smaller shapes, coordinated

with the pitch and size of the thermal vias. The drawing in Figure 26 is representational. Such a structure should

result in a solder joint area of 80% to 90% of the ePad area. To achieve the specified thermal performance, at

least 70% of the ePad should be soldered to the thermal land.

SiI 163B PanelLink Receiver

Data Sheet

35 SiI-DS-0055-C

100-pin TQFP Package Dimensions and Marking Specification

E1 F1

Detail

Drawing is not

to scale.

Pin count is

representative.

Refer to

product

specifications.

Cross-sectional representation to show

package thickness.

SiIxxxxrpppccc

LNNNNN.NLLL

YYWW

X.XX

Device #

Lot #

Date Code

Rev. Code

e/2

Detail A Detail B

0.08 R min

0.20 min

0.08/0.20 R

lead cross-

section

JEDEC Package Code MS026AED-HD

typ max

A Thickness 1.20

A1 Stand-off 0.15

A2 Body Thickness 1.00 1.05

D1 Body Size 14.00 14.00

E1 Body Size 14.00 14.00

F1 Footprint 16.00 16.00

G1 Footprint 16.00 16.00

Lead Count 100 —

L1 Lead Length 1.00 —

L Lead Foot 0.60 0.75

b Lead Width 0.20 0.27

e Lead Pitch 0.50 —

Dimensions in millimeters.

Overall thickness A=A1+A2.

SiIxxxxrppppccc

Product

Designation

Revision

Package

Type

Count

Universal Package:

SiI163BCTG100

Legend Description

LNNNNN.NLL

Lot Number

YY Year of Mfr

WW Week of Mfr

Rev Code X.XX

Figure 27. Package Dimensions and Marking Specification

Marking Specification

Marking drawing is not to scale. Pin counts are representative and may not match the pin count of this product.

Ordering Information

Production Part Number: SiI163BCTG100

SiI 163B PanelLink Receiver

Data Sheet

36 SiI-DS-0055-C

Summary of Changes

The following table lists the major changes to this document up to the present revision.

Revision Date Pages Changes

A 03/2002 — Original release.

B 08/2004 3, 32, 33-34 Added ePad description. Slave SCDT Stablilization guideline.

C 07/2005 33 Fixed ePad dimensions. Part ordering number updated

Silicon Image, Inc. Tel: (408) 616-4000

1060 E. Arques Avenue

Sunnyvale, CA 94085

USA

Fax: (408) 830-9530

E-mail: salessupport@siimage.com

Web: www.siliconimage.com