Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK HMC792LP4E v00.0609 ATTENUATORS - DIGITAL - SMT 8 0.25 dB LSB GaAs MMIC 6-BIT DIGITAL ATTENUATOR, DC - 6 GHz Typical Applications Features The HMC792LP4E is ideal for: 0.25 dB LSB Steps to 15.75 dB * Cellular/3G Infrastructure Power-Up State Selection * WiBro / WiMAX / 4G High Input IP3: +55 dBm * Microwave Radio & VSAT Low Insertion Loss: 1.8 dB @ 2.0 GHz * Test Equipment and Sensors TTL/CMOS Compatible, Serial, Parallel or Latched Parallel Control * IF & RF Applications 0.2 dB Typical Step Error Single +3V or +5V Supply 24 Lead 4x4mm SMT Package: 16mm2 Functional Diagram General Description The HMC792LP4E is a broadband 6-bit GaAs IC Digital Attenuator in a low cost leadless SMT package. This versatile digital attenuator incorporates off-chip AC ground capacitors for near DC operation, making it suitable for a wide variety of RF and IF applications. The dual mode control interface is CMOS/TTL compatible, and accepts either a three wire serial input or a 6 bit parallel word. The HMC792LP4E also features a user selectable power up state and a serial output port for cascading other Hittite serial controlled components. The HMC792LP4E is housed in a RoHS compliant 4x4 mm QFN leadless package, and requires no external matching components. Electrical Specifications, TA = +25 C, Vctl = 0/+Vdd Parameter Frequency (GHz) Typ. Max. Vdd = +3V Min. Typ. Max. Vdd = +5V 2.4 5.0 1.8 3.3 2.4 5.0 Units Insertion Loss DC - 3.0 GHz 3.0 - 6.0 GHz 1.8 3.3 Attenuation Range DC - 6.0 GHz 15.75 15.75 dB dB dB Return Loss (RF1, RF2, All Atten. States) DC - 6.0 GHz 17 17 dB Attenuation Accuracy: (Referenced to Insertion Loss) All Attenuation States DC - 0.8 GHz 0.8 - 3.0 GHz 3.0 - 4.0 GHz 4.0 - 6.0 GHz (0.2 + 4% of Atten. Setting) Max. (0.2 + 3% of Atten. Setting) Max. (0.2 + 5% of Atten. Setting) Max. (0.2 + 6% of Atten. Setting) Max. dB dB dB dB 0.05 - 0.15 GHz 0.15 - 6.0 GHz 22 27 22 30 dBm dBm Input Third Order Intercept Point (Two-Tone Input Power= 10 dBm Each Tone) DC - 6.0 GHz 55 55 dBm Switching Characteristics DC - 6.0 GHz 110 150 110 150 ns ns 1.4 1.6 mA Input Power for 0.1 dB Compression tRISE, tFALL (10/90% RF) tON, tOFF (50% CTL to 10/90% RF) Supply Current 8-1 Min. DC - 6.0 GHz For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC792LP4E v00.0609 0.25 dB LSB GaAs MMIC 6-BIT DIGITAL ATTENUATOR, DC - 6 GHz Insertion Loss vs. Temperature (Only Major States are Shown) -1 -2 -3 +25 C +85 C -40 C -4 -5 -10 -15 -20 -5 0 1 2 3 4 5 0 6 1 2 Input Return Loss [1] 4 5 6 5 6 Output Return Loss [1] (Only Major States are Shown) (Only Major States are Shown) 0 0 -5 -5 -10 -10 RETURN LOSS (dB) RETURN LOSS (dB) 3 FREQUENCY (GHz) FREQUENCY (GHz) -15 -20 -25 -30 -35 -15 -20 -25 ATTENUATORS - DIGITAL - SMT 0 NORMALIZED ATTENUATION (dB) INSERTION LOSS (dB) 0 -30 -35 -40 -40 0 1 2 3 4 5 6 0 1 2 FREQUENCY (GHz) 1 1 6GHz 0.8 0.6 0.4 0.4 BIT ERROR (dB) 0.6 0.2 0 -0.2 -0.4 4 Bit Error vs. Attenuation State [2] 6 GHz 0.8 3 FREQUENCY (GHz) Bit Error vs. Attenuation State BIT ERROR (dB) 8 Normalized Attenuation [1] [1] 1GHz, 2GHz 100MHz, 4GHz -0.6 4GHz 0.2 0 -0.2 2GHz -0.4 900MHz -0.6 -0.8 -0.8 -1 -1 0 4 8 12 ATTENUATION STATE (dB) 16 0 4 8 12 16 ATTENUATION STATE (dB) [1] Data taken with broadband DC blocks on RF ports, Vdd = 5V [2] Data taken with ACG capacitors, C4, C5 & C6 removed. See application circuit and note. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 8-2 HMC792LP4E v00.0609 0.25 dB LSB GaAs MMIC 6-BIT DIGITAL ATTENUATOR, DC - 6 GHz Bit Error vs. Frequency Bit Error vs. Frequency [2] (Only Major States are Shown) (Only Major States are Shown) 2 2 1.5 1.5 15.75 dB 15.75 dB 1 BIT ERROR (dB) BIT ERROR (dB) 1 0.5 0 -0.5 0.5 0 -0.5 -1 -1 -1.5 -1.5 -2 0 1 2 3 4 5 -2 6 0 1 2 FREQUENCY (GHz) 5 6 Bit State at Each Frequency is Shown) 1 70 0.8 65 0.6 60 0.4 IP3 (dBm) 0.2 0 -0.2 -0.4 55 50 45 +25 C +85 C -40 C 40 35 -0.8 -1 30 0 1 2 3 4 5 6 0 1 2 3 4 5 6 FREQUENCY (GHz) FREQUENCY (GHz) Input Power for 0.1dB Compression @ Vdd = 3V (Detail of Low Frequency Roll-Off) Input Power for 0.1dB Compression @ Vdd = 5V (Detail of Low Frequency Roll-Off) 32 32 30 30 28 28 P0.1dB (dBm) P0.1dB (dBm) 4 Input IP3 vs. Temperature (Worst Case Major -0.6 26 24 22 26 24 22 20 20 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 FREQUENCY (GHz) 8-3 3 FREQUENCY (GHz) Worst Case Step Error Between Successive Attenuation States (Only Major States are Shown) STEP ERROR (dB) ATTENUATORS - DIGITAL - SMT 8 0.8 0.9 1 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 FREQUENCY (GHz) For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC792LP4E v00.0609 0.25 dB LSB GaAs MMIC 6-BIT DIGITAL ATTENUATOR, DC - 6 GHz The HMC792LP4E contains a 3-wire SPI compatible digital interface (SERIN, CLK, LE). The serial control interface is activated when P/S is kept high. The 6-bit serial word must be loaded MSB first. The positive-edge sensitive CLK and LE requires clean transitions. If mechanical switches are used, sufficient debouncing should be provided. When LE is high, 6-bit data in the serial input register is transferred to the attenuator. When LE is high CLK is masked to prevent data transition during output loading. When P/S is low, 3-wire SPI interface inputs (SERIN, CLK, LE) are disabled and the input register is loaded with parallel digital inputs (D0-D5). When LE is high, 6-bit parallel data changes the state of the part per truth table. For all modes of operations, the attenuation state will stay constant while LE is kept low. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 8 ATTENUATORS - DIGITAL - SMT Serial Control Interface 8-4 HMC792LP4E v00.0609 0.25 dB LSB GaAs MMIC 6-BIT DIGITAL ATTENUATOR, DC - 6 GHz ATTENUATORS - DIGITAL - SMT 8 Timing Diagram (Latched Parallel Mode) Parallel Mode (Direct Parallel Mode & Latched Parallel Mode) Parameter Typ. Min. serial period, tSCK 100 ns Control set-up time, tCS 20 ns Control hold-time, tCH 20 ns LE setup-time, tLN 10 ns Min. LE pulse width, tLEW 10 ns Min LE pulse spacing, tLES 630 ns Serial clock hold-time from LE, tCKN 10 ns Hold Time, tPH. 0 ns Latch Enable Minimum Width, tLEN 10 ns Setup Time, tPS 2 ns Note: The parallel mode is enabled when P/S is set to low. Direct Parallel Mode - The attenuation state is changed by the control voltage inputs D0-D5 directly. The LE (Latch Enable) must be at a logic high at all times to control the attenuator in this manner. Latched Parallel Mode - The attenuation state is selected using the control voltage inputs D0-D5 and set while the LE is in the Low state. The attenuator will not change state while LE is Low. Once all Control Voltage Inputs are at the desired states the LE is pulsed. See timing diagram above for reference. Power-Up States PUP Truth Table If LE is set to logic LOW at power-up, the logic state of PUP1 and PUP2 determines the power-up state of the part per PUP truth table. If the LE is set to logic HIGH at power-up, the logic state of D0-D5 determines the power-up state of the part per truth table. The attenuator latches in the desired power-up state approximately 200 ms after power-up. Power-On Sequence The ideal power-up sequence is: GND, Vdd, digital inputs, RF inputs. The relative order of the digital inputs are not important as long as they are powered after Vdd / GND Control Voltage Table State Vdd = +3V Vdd = +5V Low 0 to 0.5V @ <1 A 0 to 0.8V @ <1 A High 2 to 3V @ <1 A 2 to 5V @ <1 A LE PUP1 PUP2 Relative Attenuation 0 0 0 -15.75 0 1 0 -12 0 0 1 -8 0 1 1 Insertion Loss 1 X X 0 to -15.75 dB Note: The logic state of D0 - D5 determines the power-up state per truth table shown below when LE is high at power-up. Truth Table D5 D4 Control Voltage Input D3 D2 D1 D0 Reference Insertion Loss High High High High High High 0 dB High High High High High Low -0.25 dB High High High High Low High -0.5 dB High High High Low High High -1 dB High High Low High High High -2 dB High Low High High High High -4 dB Low High High High High High -8 dB Low Low Low Low Low Low -15.75 dB Any combination of the above states will provide an attenuation equal to the sum of the bits selected. 8-5 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC792LP4E v00.0609 0.25 dB LSB GaAs MMIC 6-BIT DIGITAL ATTENUATOR, DC - 6 GHz RF Input Power (DC - 6 GHz) +30 dBm Digital Inputs (D0 to D5, P/S, CLK, SERIN, LE, PUP1, PUP2) -0.5 to Vdd +0.5 Bias Voltage (Vdd) 5.6V Channel Temperature 150 C Continuous Pdiss (T = 85 C) (derate 11.5 mW/C above 85 C) [1] 0.748 W Thermal Resistance (Channel to package bottom) 87 C/W Storage Temperature -65 to +150 C Operating Temperature -40 to +85 C ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Outline Drawing ATTENUATORS - DIGITAL - SMT 8 Absolute Maximum Ratings NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. Package Information Part Number Package Body Material Lead Finish HMC792LP4E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL Rating MSL1 [2] Package Marking [1] H792 XXXX [1] 4-Digit lot number XXXX [2] Max peak reflow temperature of 260 C For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 8-6 HMC792LP4E v00.0609 0.25 dB LSB GaAs MMIC 6-BIT DIGITAL ATTENUATOR, DC - 6 GHz ATTENUATORS - DIGITAL - SMT 8 8-7 Pin Descriptions Pin Number Function 1 P/S 2 CLK Description Interface Schematic See truth table, control voltage table and timing diagram. 3 SERIN 4 LE 5, 14 GND These pins and package bottom must be connected to RF/DC ground. 6, 13 RF1, RF2 These pins are DC coupled and matched to 50 Ohms. Blocking capacitors are required. Select value based on lowest frequency of operation. 7 - 12 ACG1 - ACG6 External capacitors to ground is required. Select value for lowest frequency of operation. Place capacitor as close to pins as possible. 15 SEROUT Serial input data delayed by 6 clock cycles. 16, 17 PUP2, PUP1 19 - 24 D5, D4, D3, D2, D1, D0 18 Vdd See truth table, control voltage table and timing diagram. Supply voltage For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC792LP4E v00.0609 0.25 dB LSB GaAs MMIC 6-BIT DIGITAL ATTENUATOR, DC - 6 GHz 8 ATTENUATORS - DIGITAL - SMT Application Circuit For frequencies less than 700 MHz, the use of ACG capacitors C4, C5 and C6 is recommended. For frequencies greater than 700 MHz, the HMC792LP4E has similar performance with and without the ACG capacitors. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 8-8 HMC792LP4E v00.0609 0.25 dB LSB GaAs MMIC 6-BIT DIGITAL ATTENUATOR, DC - 6 GHz Evaluation PCB ATTENUATORS - DIGITAL - SMT 8 List of Materials for Evaluation PCB 118853 [1] Item Description J1, J2 PCB Mount SMA Connector J3 18 Pin DC Connector J4 DC Pin C1, C2 100 pF Capacitor, 0402 Pkg. C3 1000 pF Capacitor, 0402 Pkg. C4 - C6 330 pF Capacitor, 0402 Pkg. U1 HMC792LP4E Digital Attenuator PCB [2] 118852 Evaluation PCB The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Arlon 25FR or Rogers 4350 8-9 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC792LP4E v00.0609 0.25 dB LSB GaAs MMIC 6-BIT DIGITAL ATTENUATOR, DC - 6 GHz 8 ATTENUATORS - DIGITAL - SMT Notes: For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 8 - 10