Important notice Dear Customer, On 7 February 2017 the former NXP Standard Product business became a new company with the tradename Nexperia. Nexperia is an industry leading supplier of Discrete, Logic and PowerMOS semiconductors with its focus on the automotive, industrial, computing, consumer and wearable application markets In data sheets and application notes which still contain NXP or Philips Semiconductors references, use the references to Nexperia, as shown below. Instead of http://www.nxp.com, http://www.philips.com/ or http://www.semiconductors.philips.com/, use http://www.nexperia.com Instead of sales.addresses@www.nxp.com or sales.addresses@www.semiconductors.philips.com, use salesaddresses@nexperia.com (email) Replace the copyright notice at the bottom of each page or elsewhere in the document, depending on the version, as shown below: - (c) NXP N.V. (year). All rights reserved or (c) Koninklijke Philips Electronics N.V. (year). All rights reserved Should be replaced with: - (c) Nexperia B.V. (year). All rights reserved. If you have any questions related to the data sheet, please contact our nearest sales office via e-mail or telephone (details via salesaddresses@nexperia.com). Thank you for your cooperation and understanding, Kind regards, Team Nexperia INTEGRATED CIRCUITS 74F367 Hex buffer/driver Product data Replaces Product specification 74F365/74F367 of 2000 Jun 30 2004 Jan 30 Philips Semiconductors Product data Hex buffer/driver 74F367 FEATURES * High-impedance NPN base inputs for reduced loading TYPE TYPICAL PROPAGATION DELAY TYPICAL SUPPLY CURRENT (TOTAL) 74F367 5.0 ns 36 mA (20 A in HIGH and LOW states) * High-speed * Bus oriented * 3-State buffer outputs sink 64 mA ORDERING INFORMATION COMMERCIAL RANGE: VCC = 5 V 10%; Tamb = 0 C to +70 C Type number Package Name Description Version N74F367N DIP16 plastic dual in-line package; 16 leads (300 mil) SOT38-4 N74F367D SO16 plastic small outline package; 16 leads; body width 3.9 mm SOT109-1 INPUT AND OUTPUT LOADING AND FAN-OUT TABLE PINS DESCRIPTION 74F(U.L.) HIGH / LOW LOAD VALUE HIGH / LOW 1.0 / 0.033 20 A / 20 A I0 - I5 Inputs OE0, OE1 Output enable inputs (active-LOW) 1.0 / 0.033 20 A / 20 A Y0 - Y5 Data Outputs 750 / 106.7 15 mA / 64 mA NOTE: One (1.0) FAST Unit Load (U.L.) is defined as: 20 A in the HIGH state and 0.6 mA in the LOW state. PIN CONFIGURATION OE0 1 16 VCC I0 2 15 OE1 Y0 3 14 I5 I1 4 13 Y5 74F367 Y1 5 12 I4 I2 6 11 Y4 Y2 7 10 I3 GND 8 9 Y3 SF00905 2004 Jan 30 2 Philips Semiconductors Product data 74F367 Hex buffer/driver LOGIC SYMBOL LOGIC SYMBOL (IEEE/IEC) 74F367 74F367 2 4 I0 6 I1 I2 10 12 I3 14 I4 1 EN1 15 EN2 2 I5 1 3 1 OE0 4 15 OE1 6 7 10 9 Y0 Y1 Y2 Y3 Y4 Y5 12 3 VCC = Pin 16 GND = Pin 8 5 7 9 11 2 14 13 5 11 13 SF00907 SF00906 LOGIC DIAGRAM FUNCTION TABLE INPUTS OUTPUTS 74F367 OE0 1 I0 I1 I2 2 4 6 I3 10 3 5 7 9 Y0 Y1 H L X Z Y2 Y3 OE1 15 I4 12 I5 14 VCC = Pin 16 GND = Pin 8 2004 Jan 30 11 13 Y4 Y5 SF01442 3 = = = = OEn In Yn L L L L H H H X Z HIGH voltage level LOW voltage level Don't care High impedance "off" state Philips Semiconductors Product data 74F367 Hex buffer/driver ABSOLUTE MAXIMUM RATINGS Operation beyond the limits set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the operating free-air temperature range. SYMBOL PARAMETER RATING UNIT VCC Supply voltage range -0.5 to +7.0 V VIN Input voltage range -0.5 to +7.0 V IIN Input current range -30 to +5 mA VOUT Voltage applied to output in HIGH output state range -0.5 to 5.5 V IOUT Current applied to output in LOW output state Tamb Operating free-air temperature range Tstg Storage temperature range 128 mA 0 to +70 C -65 to +150 C LIMITS UNIT RECOMMENDED OPERATING CONDITIONS SYMBOL PARAMETER MIN TYP MAX 5.5 V VCC Supply voltage 4.5 5.0 VIH HIGH-level input voltage 2.0 - - V VIL LOW-level input voltage - - 0.8 V IIK Input clamp current - - -18 mA IOH HIGH-level output current - - -15 mA IOL LOW-level output current - - 64 mA Tamb Operating free-air temperature range 0 - 70 C 2004 Jan 30 4 Philips Semiconductors Product data 74F367 Hex buffer/driver DC ELECTRICAL CHARACTERISTICS Over recommended operating free-air temperature range unless otherwise noted. SYMBOL VCC = MIN; VIL = MAX; VIH = MIN; IOH = -3 mA VOH O LIMITS TEST CONDITIONS1 PARAMETER HIGH level output voltage HIGH-level VCC = MIN; VIL = MAX; VIH = MIN; IOH = -15 mA VCC = MIN; VIL = MAX; VIH = MIN; IOL = MAX VOL O Low level output voltage Low-level VIK Input clamp voltage II Input current at maximum input voltage IIH IIL UNIT MIN TYP2 MAX 10% VCC 2.4 - - V 5% VCC 2.7 3.3 - V 10% VCC 2.0 - - V 5% VCC 2.0 - - V 10% VCC - - 0.55 V 5% VCC - 0.42 0.55 V VCC = MIN; II = IIK - -0.73 -1.2 V VCC = 0 V; VI = 7.0 V - - 100 A HIGH-level input current VCC = MAX; VI = 2.7 V - - 20 A LOW-level input current VCC = MAX; VI = 0.5 V - - -20 A IOZH Off-state output current, HIGH-level voltage applied VCC = MAX; VO = 2.7 V - - 50 A IOZL Off-state output current, LOW-level voltage applied VCC = MAX; VO = 0.5 V - - -50 A IOS Short-circuit output current3 VCC = MAX -100 - -225 mA - 25 35 mA ICC Supply current (total) - 47 62 mA - 35 48 mA ICCH ICCL VCC = MAX ICCZ NOTES: 1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type. 2. All typical values are at VCC = 5 V, Tamb = 25 C. 3. Not more than one output should be shorted at a time. For testing IOS, the use of high-speed test apparatus and/or sample-and-hold techniques are preferable in order to minimize internal heating and more accurately reflect operational values. Otherwise, prolonged shorting of a HIGH output may raise the chip temperature well above normal and thereby cause invalid readings in other parameter tests. In any sequence of parameter tests, IOS tests should be performed last. AC ELECTRICAL CHARACTERISTICS LIMITS SYMBOL PARAMETER TEST CONDITIONS Tamb = -55 C to +125 C VCC = +5.0 V 10% CL = 50 pF; RL = 500 UNIT MIN TYP MAX MIN MAX Waveform 1 2.5 2.5 4.5 5.5 6.5 7.0 2.0 2.0 7.0 7.5 ns ns Output Enable time to HIGH or LOW level Waveform 2 Waveform 3 3.0 3.0 5.5 6.5 7.5 8.5 3.0 3.0 8.5 9.0 ns ns Output Disable time from HIGH to LOW level Waveform 2 Waveform 3 2.0 2.0 4.5 4.0 6.5 6.5 2.0 2.0 7.0 7.0 ns ns tPLH tPHL Propagation delay In to Yn tPZH tPZL tPHZ tPLZ 2004 Jan 30 Tamb = +25 C VCC = +5.0 V CL = 50 pF; RL = 500 5 Philips Semiconductors Product data 74F367 Hex buffer/driver AC WAVEFORMS For all waveforms, VM = 1.5 V In VM VM tPLH tPHL Yn VM VM SF00914 Waveform 1. For non-inverting outputs OE VM OE VM tPZH VM VOH - 0.3 V tPHZ VM tPZL tPLZ 3.5 V Yn VM VM Yn 0V VOL + 0.3 V SF00913 SF00915 Waveform 2. 3-State Output Enable time to HIGH level and Output Disable time from HIGH level Waveform 3. 3-State Output Enable time to LOW level and Output Disable time from LOW level TEST CIRCUIT AND WAVEFORM VCC 7.0 V VIN RL VOUT PULSE GENERATOR tw 90% NEGATIVE PULSE VM CL AMP (V) VM 10% D.U.T. RT 90% 10% tTHL (tf ) tTLH (tr ) tTLH (tr ) tTHL (tf ) 0V RL AMP (V) 90% 90% Test Circuit for 3-State Outputs POSITIVE PULSE VM VM 10% TEST tPLZ tPZL All other SWITCH closed closed open DEFINITIONS: RL = Load resistor; see AC electrical characteristics for value. CL = Load capacitance includes jig and probe capacitance; see AC electrical characteristics for value. RT = Termination resistance should be equal to ZOUT of pulse generators. 10% tw SWITCH POSITION 0V Input Pulse Definition INPUT PULSE REQUIREMENTS family amplitude VM 74F 3.0 V 1.5 V rep. rate 1 MHz tw tTLH 500 ns 2.5 ns tTHL 2.5 ns SF00777 2004 Jan 30 6 Philips Semiconductors Product data 74F367 Hex buffer/driver DIP16: plastic dual in-line package; 16 leads (300 mil) 2004 Jan 30 7 SOT38-4 Philips Semiconductors Product data 74F367 Hex buffer/driver SO16: plastic small outline package; 16 leads; body width 3.9 mm 2004 Jan 30 8 SOT109-1 Philips Semiconductors Product data 74F367 Hex buffer/driver REVISION HISTORY Rev Date Description _4 20040130 Product data (9397 750 12742). 853-0042 ECN 01-A15335 of 21 January 2004. Replaces 74F365_74F367_3 dated 2000 Jun 30 (9397 750 07283). Modifications: * Delete all references to 74F365 (product discontinued). _3 20000630 Product specification (9397 750 07283). ECN 853-0042 24024 of 30 June 2000. Supersedes data of 1999 Jan 08. Data sheet status Level Data sheet status [1] Product status [2] [3] Definitions I Objective data Development This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. II Preliminary data Qualification This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. III Product data Production This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). [1] Please consult the most recently issued data sheet before initiating or completing a design. [2] The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. [3] For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status. Definitions Short-form specification -- The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition -- Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information -- Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Disclaimers Life support -- These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes -- Philips Semiconductors reserves the right to make changes in the products--including circuits, standard cells, and/or software--described or contained herein in order to improve design and/or performance. When the product is in full production (status `Production'), relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Koninklijke Philips Electronics N.V. 2004 All rights reserved. Printed in U.S.A. Contact information For additional information please visit http://www.semiconductors.philips.com. Fax: +31 40 27 24825 Date of release: 01-04 For sales offices addresses send e-mail to: sales.addresses@www.semiconductors.philips.com. 2004 Jan 30 Document order number: 9 9397 750 12742