TinyLogic UHS Buffer with Three-State Output NC7SZ125 Description The NC7SZ125 is a single buffer with three-state output from ON Semiconductor's Ultra-High Speed (UHS) of TinyLogic. The device is fabricated with advanced CMOS technology to achieve ultra high speed with high output drive while maintaining low static power dissipation over a very broad VCC operating range. The device is specified to operate over the 1.65 V to 5.5 V range. The inputs and output are high impedance above ground when VCC is 0 V. Inputs tolerate voltages up to 5.5 V independent of VCC operating voltage. The output tolerates voltages above VCC when in the 3-STATE condition. www.onsemi.com MARKING DIAGRAMS DDKK XYZ SIP6 CASE 127EB Pin 1 Features * * * * * * * * * * Ultra-High Speed: tPD = 2.6 ns (Typical) into 50 pF at 5 V VCC High Output Drive: 24 mA at 3 V VCC Broad VCC Operating Range: 1.65 V to 5.5 V Matches Performance of LCX when Operated at 3.3 V VCC Power Down High-Impedance Inputs / Outputs Over-Voltage Tolerance Inputs Facilitate 5 V to 3 V Translation Proprietary Noise / EMI Reduction Circuitry Ultra-Small MicroPakTM Packages Space-Saving SC-74A and SC-88A Packages These Devices are Pb-Free, Halogen Free/BFR Free and are RoHS Compliant DDKK XYZ UDFN6 CASE 517DP Pin 1 SC-74A CASE 318BQ SC-88A CASE 419A-02 7Z25 M* * Z25 M* * IEEE / IEC A OE 1 EN Y DD, 7Z25, Z25 = Specific Device Code KK = 2-Digit Lot Run Traceability Code XY = 2-Digit Date Code Format Z = Assembly Plant Code M = Date Code * = Pb-Free Package (Microdot may be in either location) Figure 1. Logic Symbol ORDERING INFORMATION See detailed ordering, marking and shipping information in the package dimensions section on page 6 of this data sheet. (c) Semiconductor Components Industries, LLC, 1996 January, 2021 - Rev. 4 1 Publication Order Number: NC7SZ125/D NC7SZ125 Pin Configurations OE 1 5 OE 1 6 VCC VCC A 2 A 2 GND 3 4 Y 5 NC GND 3 Figure 2. SC-88A and SC-74A (Top View) 4 Y Figure 3. MicroPak (Top Through View) PIN DEFINITIONS FUNCTION TABLE Pin # SC-88A / SC74A Pin # MicroPak Name Inputs 1 1 OE Input 2 2 A Input 3 3 GND Ground 4 4 Y Output 5 6 VCC Supply Voltage 5 NC No Connect Description A Y L L L L H H H X Z H = HIGH Logic Level L = LOW Logic Level X = HIGH or LOW Logic Level Z = HIGH Impedance State www.onsemi.com 2 Output OE NC7SZ125 ABSOLUTE MAXIMUM RATINGS Symbol Min Max Unit VCC Supply Voltage -0.5 6.5 V VIN DC Input Voltage -0.5 6.5 V DC Output Voltage -0.5 6.5 V VOUT Parameter IIK DC Input Diode Current VIN < 0 V - -50 mA IOK DC Output Diode Current VOUT < 0 V - -50 mA IOUT DC Output Current - 50 mA DC VCC or Ground Current - 50 mA -65 +150 C ICC or IGND TSTG Storage Temperature Range TJ Junction Temperature Under Bias - +150 C TL Junction Lead Temperature (Soldering, 10 Seconds) - +260 C PD Power Dissipation in Still Air SC-74A - 390 mW SC-88A - 332 MicroPak-6 - 812 MicroPak2TM-6 - 812 Human Body Model, JEDEC: JESD22-A114 - 4000 Charge Device Model, JEDEC: JESD22-C101 - 2000 ESD V Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. RECOMMENDED OPERATING CONDITIONS Symbol VCC VIN VOUT Parameter Min Max Unit Supply Voltage Operating 1.65 5.50 V Supply Voltage Data Retention 1.50 5.50 Input Voltage Output Voltage TA Operating Temperature tr, tf Input Rise and Fall Times JA Conditions Thermal Resistance 0 5.5 V Active State 0 VCC V Three-State 0 5.5 -40 +85 C VCC at 1.8 V, 2.5 V 0.2 V 0 20 ns/V VCC at 3.3 V 0.3 V 0 10 VCC at 5.0 V 0.5 V 0 5 SC-74A - 320 SC-88A - 377 MicroPak-6 - 154 MicroPak2-6 - 154 C/W Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond the Recommended Operating Ranges limits may affect device reliability. 1. Unused inputs must be held HIGH or LOW. They may not float. www.onsemi.com 3 NC7SZ125 DC ELECTICAL CHARACTERISTICS TA = +25C Symbol VIH VIL VOH Parameter HIGH Level Input Voltage LOW Level Input Voltage HIGH Level Output Voltage Typ Max Min Max Unit 1.65 to 1.95 0.65 VCC - - 0.65 VCC - V 2.30 to 5.50 0.70 VCC - - 0.70 VCC - 1.65 to 1.95 - - 0.35 VCC - 0.35 VCC 2.30 to 5.50 - - 0.30 VCC - 0.30 VCC 1.55 1.65 - 1.55 - 1.70 1.80 - 1.70 - 2.30 2.20 2.30 - 2.20 - 3.00 2.90 3.00 - 2.90 - 4.50 4.40 4.50 - 4.40 - VCC (V) 1.65 1.80 VOL LOW Level Output Voltage TA = -40 to +85C Min Conditions VIN = VIH or VIL, IOH = -100 A 1.65 IOH = -4 mA 1.29 1.52 - 1.29 - 2.30 IOH = -8 mA 1.90 2.15 - 1.90 - 3.00 IOH = -16 mA 2.40 2.80 - 2.40 - 3.00 IOH = -24 mA 2.30 2.68 - 2.30 - 4.50 IOH = -32 mA 3.80 4.20 - 3.80 - 1.65 VIN = VIH or VIL, IOL = 100 A - 0.00 0.10 - 0.00 - 0.00 0.10 - 0.10 2.30 - 0.00 0.10 - 0.10 3.00 - 0.00 0.10 - 0.10 4.50 - 0.00 0.10 - 0.10 1.80 1.65 IOL = 4 mA - 0.80 0.24 - 0.24 2.30 IOL = 8 mA - 0.10 0.30 - 0.30 3.00 IOL = 16 mA - 0.15 0.40 - 0.40 3.00 IOL = 24 mA - 0.22 0.55 - 0.55 4.50 V V V IOL = 32 mA - 0.22 0.55 - 0.55 1.65 to 5.5 0 VIN 5.5 V - - 1 - 10 A 3-STATE Output Leakage 0 to 5.5 VIN = VIH or VIL 0 VO 5.5 V - - 1 - 10 A IOFF Power Off Leakage Current 0 VIN or VOUT = 5.5 V - - 1 - 10 A ICC Quiescent Supply Current VIN = 5.5 V, GND - - 2 - 20 A IIN Input Leakage Current IOZ 1.65 to 5.50 www.onsemi.com 4 NC7SZ125 AC ELECTRICAL CHARACTERISTICS TA = +25C TA = -40 to +85C Min Typ Max Min Max Unit - 6.4 13.2 - 13.8 ns - 5.3 11.0 - 11.5 2.50 0.20 - 3.4 7.5 - 8.0 3.30 0.30 - 2.5 5.2 - 5.5 5.00 0.50 - 2.1 4.5 - 4.8 3.30 0.30 CL = 50 pF, RD = 500 5.00 0.50 S1 = OPEN - 3.2 5.7 - 6.0 - 2.6 5.0 - 5.3 CL = 50 pF, RD = 500 1.80 RU = 500 2.50 0.20 S1 = GND for tPZH S1 = VIN for tPZL 3.30 0.30 VIN = 2 * VCC - 8.4 15.0 - 15.6 - 7.0 12.5 - 13.0 - 4.6 8.5 - 9.0 - 3.5 6.2 - 6.5 5.00 0.50 - 2.8 5.5 - 5.8 CL = 50 pF, 1.65 RD = 500 1.80 RU = 500 2.50 0.20 S1 = GND for tPHZ S1 = VIN for tPLZ 3.30 0.30 VIN = 2 * VCC - 6.5 13.2 - 14.5 - 5.4 11.0 - 12.0 - 3.5 8.0 - 8.5 - 2.8 5.7 - 6.0 5.00 0.50 - 2.1 4.7 - 5.0 Input Capacitance 0.00 - 4 - - - COUT Output Capacitance 0.00 - 8 - - - CPD Power Dissipation Capacitance (Note 2) (Figure 5) 3.30 - 17 - - - Symbol Parameter VCC (V) tPLH, tPHL Propagation Delay (Figure 4, 6) 1.65 1.80 tPZL, tPZH tPLZ, tPHZ CIN Output Enable Time (Figure 4, 6) Output Disable Time (Figure 4, 6) Conditions CL = 15 pF, RD = 1 M S1=OPEN 1.65 ns pF pF 2. CPD is defined as the value of the internal equivalent capacitance which is derived from dynamic operating current consumption (ICCD) at no output loading and operating at 50% duty cycle. CPD is related to ICCD dynamic operating current by the expression: ICCD = (CPD) (VCC) (fIN) + (ICCstatic). www.onsemi.com 5 NC7SZ125 VI OPEN GND VCC OE INPUT RU OUTPUT INPUT CL RD NOTE: 3. CL includes load and stray capacitance; Input PRR = 1.0 MHz; tW = 500 ns Figure 4. AC Test Circuit VCC A OE OUTPUT INPUT NOTE: 4. Input = AC Waveform; tr = tf = 1.8 ns; PRR = 10 MHz; Duty Cycle = 50%. Figure 5. ICCD Test Circuit Figure 6. AC Waveforms ORDERING INFORMATION Part Number Top Mark Operating Temperature Packages Shipping NC7SZ125M5X 7Z25 -40 to +85C SC-74A 3000 / Tape & Reel NC7SZ125P5X Z25 -40 to +85C SC-88A 3000 / Tape & Reel NC7SZ125L6X DD -40 to +85C MicroPak 5000 / Tape & Reel NC7SZ125FHX DD -40 to +85C MicroPak2 5000 / Tape & Reel For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. MicroPak and MicroPak2 are trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries. www.onsemi.com 6 MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS SIP6 1.45X1.0 CASE 127EB ISSUE O DOCUMENT NUMBER: DESCRIPTION: 98AON13590G SIP6 1.45X1.0 DATE 31 AUG 2016 Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped "CONTROLLED COPY" in red. PAGE 1 OF 1 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the rights of others. (c) Semiconductor Components Industries, LLC, 2019 www.onsemi.com MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS SC-74A CASE 318BQ ISSUE B 5 1 SCALE 2:1 5X DATE 18 JAN 2018 b 0.20 C A B E1 5 M 4 1 2 E 3 B 0.05 A1 e D A L DETAIL A NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. MOLD FLASH, PROTRUSIONS, OR GATE BURRS SHALL NOT EXCEED 0.15 PER SIDE. DIM A A1 b c D E E1 e L M TOP VIEW A SIDE VIEW DETAIL A C c SEATING PLANE END VIEW RECOMMENDED SOLDERING FOOTPRINT* MILLIMETERS MIN MAX 0.90 1.10 0.01 0.10 0.25 0.50 0.10 0.26 2.85 3.15 2.50 3.00 1.35 1.65 0.95 BSC 0.20 0.60 0_ 10 _ GENERIC MARKING DIAGRAM* 0.95 PITCH XXX MG G XXX M G 2.40 = Specific Device Code = Date Code = Pb-Free Package (Note: Microdot may be in either location) 5X 1.00 *This information is generic. Please refer to device data sheet for actual part marking. Pb-Free indicator, "G" or microdot " G", may or may not be present. Some products may not follow the Generic Marking. 5X 0.70 DIMENSIONS: MILLIMETERS *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. DOCUMENT NUMBER: DESCRIPTION: 98AON66279G SC-74A Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped "CONTROLLED COPY" in red. PAGE 1 OF 1 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the rights of others. (c) Semiconductor Components Industries, LLC, 2018 www.onsemi.com MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS SC-88A (SC-70-5/SOT-353) CASE 419A-02 ISSUE L SCALE 2:1 A NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. 419A-01 OBSOLETE. NEW STANDARD 419A-02. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. G 5 4 -B- S 1 2 DATE 17 JAN 2013 DIM A B C D G H J K N S 3 D 5 PL 0.2 (0.008) B M M N INCHES MIN MAX 0.071 0.087 0.045 0.053 0.031 0.043 0.004 0.012 0.026 BSC --0.004 0.004 0.010 0.004 0.012 0.008 REF 0.079 0.087 MILLIMETERS MIN MAX 1.80 2.20 1.15 1.35 0.80 1.10 0.10 0.30 0.65 BSC --0.10 0.10 0.25 0.10 0.30 0.20 REF 2.00 2.20 J GENERIC MARKING DIAGRAM* C K H XXXMG G SOLDER FOOTPRINT 0.50 0.0197 XXX = Specific Device Code M = Date Code G = Pb-Free Package 0.65 0.025 0.65 0.025 0.40 0.0157 1.9 0.0748 SCALE 20:1 (Note: Microdot may be in either location) *This information is generic. Please refer to device data sheet for actual part marking. Pb-Free indicator, "G" or microdot "G", may or may not be present. Some products may not follow the Generic Marking. mm inches STYLE 1: PIN 1. BASE 2. EMITTER 3. BASE 4. COLLECTOR 5. COLLECTOR STYLE 2: PIN 1. ANODE 2. EMITTER 3. BASE 4. COLLECTOR 5. CATHODE STYLE 3: PIN 1. ANODE 1 2. N/C 3. ANODE 2 4. CATHODE 2 5. CATHODE 1 STYLE 4: PIN 1. SOURCE 1 2. DRAIN 1/2 3. SOURCE 1 4. GATE 1 5. GATE 2 STYLE 6: PIN 1. EMITTER 2 2. BASE 2 3. EMITTER 1 4. COLLECTOR 5. COLLECTOR 2/BASE 1 STYLE 7: PIN 1. BASE 2. EMITTER 3. BASE 4. COLLECTOR 5. COLLECTOR STYLE 8: PIN 1. CATHODE 2. COLLECTOR 3. N/C 4. BASE 5. EMITTER STYLE 9: PIN 1. ANODE 2. CATHODE 3. ANODE 4. ANODE 5. ANODE DOCUMENT NUMBER: DESCRIPTION: 98ASB42984B STYLE 5: PIN 1. CATHODE 2. COMMON ANODE 3. CATHODE 2 4. CATHODE 3 5. CATHODE 4 Note: Please refer to datasheet for style callout. If style type is not called out in the datasheet refer to the device datasheet pinout or pin assignment. Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped "CONTROLLED COPY" in red. SC-88A (SC-70-5/SOT-353) PAGE 1 OF 1 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the rights of others. (c) Semiconductor Components Industries, LLC, 2018 www.onsemi.com MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS UDFN6 1.0X1.0, 0.35P CASE 517DP ISSUE O DOCUMENT NUMBER: DESCRIPTION: 98AON13593G UDFN6 1.0X1.0, 0.35P DATE 31 AUG 2016 Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped "CONTROLLED COPY" in red. PAGE 1 OF 1 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the rights of others. (c) Semiconductor Components Industries, LLC, 2019 www.onsemi.com ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. "Typical" parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Email Requests to: orderlit@onsemi.com ON Semiconductor Website: www.onsemi.com TECHNICAL SUPPORT North American Technical Support: Voice Mail: 1 800-282-9855 Toll Free USA/Canada Phone: 011 421 33 790 2910 www.onsemi.com 1 Europe, Middle East and Africa Technical Support: Phone: 00421 33 790 2910 For additional information, please contact your local Sales Representative