86A2A-B28-A13/R51L - Bourns - Datasheet.Directory

Features

■ Metal shaft and bushing

■ Consistent, smooth quality feel

■ Up to 4 sections available

■ Rotary switch option designed

for “on-off” function control

■ RoHS compliant*

81/82 - 5/8 ” Square Single-Turn Panel Control

85/86 - 5/8 ” Square Single-Turn Panel Control with Rotary Switch

*RoHS Directive 2002/95/EC Jan. 27, 2003 including annex and RoHS Recast 2011/65/EU June 8, 2011.

Speciﬁ cations are subject to change without notice.

The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time.

Users should verify actual device performance in their speciﬁ c applications.

Initial Electrical Characteristics1 Conductive Plastic Element Cermet Element

Standard Resistance Range

Linear Tapers (A, B, E, & H) ..................................................................(B & E) 1 K ohms to 1 megohm ............. (A & H) 100 ohms to 1 megohm

Audio Tapers (C, D, F, G, S, & T) .........................................................(D, G, S, & T) 1 K ohms to 1 megohm ... (C & F) 1 K ohms to 1 megohm

Total Resistance Tolerance .........................................................................±20 % or 10 % ...................................... ±10 % or 5 %

Independent Linearity .................................................................................±5 % ...................................................... ±5 %

Absolute Minimum Resistance ...................................................................2 ohms maximum .................................. 2 ohms maximum

Eﬀ ective Electrical Angle ............................................................................(Linear tapers) 240 ° ± 5 ° ...................... (Linear tapers) 240 ° ± 6 °

(Audio tapers) 225 ° ± 5 ° ...................... (Audio tapers) 225 ° ± 6 °

Contact Resistance Variation .....................................................................±1 % ...................................................... ±1 % or 3 ohms (whichever is greater)

Dielectric Withstanding Voltage (MIL-STD-202, Method 301)

Sea Level ..............................................................................................1,500 VAC minimum .............................. 1,500 VAC minimum

70,000 Feet ..........................................................................................500 VAC minimum ................................. 500 VAC minimum

Insulation Resistance (500 VDC) ................................................................1,000 megohms minimum ..................... 1,000 megohms minimum

Power Rating At 70 °C (Voltage Limited By Power Dissipation or 350 VAC, Whichever Is Less)

+70 °C Single Section Assembly .........................................................(Linear tapers) 1 watt ............................. (Linear tapers) 2 watts

(Audio tapers) 0.5 watt .......................... (Audio tapers) 1 watt

+70 °C Multiple Section Assembly.......................................................(Linear tapers) 0.5 watt/section ............. (Linear tapers) 1 watt/section

(Audio tapers) 0.25 watt/section ........... (Audio tapers) 0.5 watt/section

+125 °C ................................................................................................0 watt ..................................................... 0 watt

Theoretical Resolution ................................................................................Essentially inﬁ nite .................................. Essentially inﬁ nite

Environmental Characteristics1

Operating Temperature Range ...................................................................-40 °C to +125 °C .................................. -40 °C to +125 °C

Storage Temperature Range ......................................................................-55 °C to +125 °C .................................. -55 °C to +125 °C

Temperature Coeﬃ cient Over Storage Temperature Range ......................±1,000 ppm/°C ...................................... ±150 ppm/°C

Vibration (Single Section) ...........................................................................15 G ....................................................... 15 G

Total Resistance Shift ...........................................................................±2 % maximum ..................................... ±2 % maximum

Voltage Ratio Shift ................................................................................±5 % maximum ..................................... ±5 % maximum

Shock (Single Section) ...............................................................................30 G ....................................................... 30 G

Total Resistance Shift ...........................................................................±2 % maximum ..................................... ±2 % maximum

Voltage Ratio Shift ................................................................................±5 % maximum ..................................... ±5 % maximum

Load Life .....................................................................................................1,000 hours ........................................... 1,000 hours

Total Resistance Shift ...........................................................................±10 % maximum ................................... ±5 % maximum

Rotational Life (No Load) ............................................................................100,000 cycles ...................................... 100,000 cycles

Total Resistance Shift ...........................................................................(Linear taper) 10 ohms or ..................... (All tapers) ±5 % TRS maximum

±10 % TRS max. (whichever is greater)

(Audio taper) ±20 % maximum

Contact Resistance Variation @ 50,000 cycles

(Audio taper) ..................................................................................±3 % ...................................................... ±3 %

(Linear taper) .................................................................................±2 % ...................................................... ±2 %

Moisture Resistance (MIL-STD-202, Method 103, Condition B)

Total Resistance Shift ...........................................................................(B & E tapers) ±10 % maximum ........... ±5 % maximum (all tapers)

(D, G, S & T tapers) ±20 % maximum

Insulation Resistance (500 VDC) ..........................................................100 megohms minimum ........................ 100 megohms minimum

IP Rating .....................................................................................................IP40 ....................................................... IP40

Mechanical Characteristics

Stop Strength

1/4 ” and 1/8 ” diameter shafts ......................................................................................................................................................... 45.19 N-cm (4 lb.-in.)

7/8 ” length shaft ................................................................................................................................................................................. 22.6 N-cm (2 lb.-in.)

Mechanical Angle ...................................................................................................................................................................................................... 300 ° ±5 °

Torque

Starting and Running Torque (Non-Locking Bushings)

Single Section .................................................................................................................................................................0.14 to 1.06 N-cm (0.2 to 1.5 oz.-in.)

Dual Section ....................................................................................................................................................................0.14 to 1.06 N-cm (0.2 to 1.5 oz.-in.)

Triple Section ...................................................................................................................................................................0.35 to 1.41 N-cm (0.5 to 2.0 oz.-in.)

Quadruple Section ..........................................................................................................................................................0.35 to 1.41 N-cm (0.5 to 2.0 oz.-in.)

Starting and Running Torque (Locking Bushings) ..................................................................................................... 0.14 to 2.82 N-cm (0.2 to 4.0 oz.-in.)

Shaft Locking Torque with Locknut @ 10 in-lb. (B & E Bushings) ........................................................................................................ 14 N-cm (20 oz-in.)

Mounting ...................................................................................................................................................................1.7-2.0 N-m (15-18 lb.-in.) maximum

Weight (Single Section).............................................................................................................................................................................. 21 grams maximum

(Each Additional Section) ...................................................................................................................................................................... 6 grams maximum

Terminals .......................................................................................................................................................................... Printed circuit terminals or J-Hooks

Soldering Condition .................................................................. Recommended hand soldering using Sn95/Ag5 no clean solder, 0.025 ” wire diameter.

Maximum temperature 399 °C (750 °F) for 3 seconds. No wash process to be used with no clean ﬂ ux.

Marking .......................................................................... Manufacturer’s trademark, wiring diagram, date code and resistance, manufacturer’s part number

Ganging (multiple section potentiometers) ..................................................................................................................................................... 4 cup maximum

Hardware ...........................................One lockwasher and one mounting nut is shipped with each potentiometer, except where noted in the part number.

For dimensional drawings see pages 3 & 4.

For ordering information see page 5.

NOTE: Model 81/82 performance speciﬁ cations do not apply to units subjected to printed circuit board cleaning procedures.

1At room ambient: +25 °C nominal and 50 % relative humidity nominal, except as noted.

Potentiometer Speciﬁ cations

*RoHS COMPLIANT

Speciﬁ cations are subject to change without notice.

The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time.

Users should verify actual device performance in their speciﬁ c applications.

81/82 - 5/8 ” Square Single-Turn Panel Control

85/86 - 5/8 ” Square Single-Turn Panel Control with Rotary Switch

Initial Electrical Characteristics1

Contacts:

DPST ...............................................................................................................................................................................N.O/N.O.,N.C./N.C. or N.O./N.C.

Power Rating (Resistive Load):

DPST ............................................................................................................ 2 A @ 125 volts RMS-60 Hz or 2 A @ 28 VDC, 1 A @ 250 volts RMS-60 Hz

Contact Resistance (0.1 VDC-10 mA) ..................................................................................................................................................... 10 milliohms nominal

Contact Bounce ................................................................................................................................................................................ 5 milliseconds maximum

Dielectric Withstanding Voltage (MIL-STD-202, Method 301)

Sea Level ............................................................................................................................................................................................. 1500 VAC minimum

Insulation Resistance ....................................................................................................................................................................... 1000 megohms minimum

Environmental Characteristics1

Operating Temperature Range ....................................................................................................................................................................... -40 °C to +70 °C

Storage Temperature Range ........................................................................................................................................................................ -65 °C to +125 °C

Vibration (Dual Section) ....................................................................................................................................................................................................... 8 G

(Triple Section) .................................................................................................................................................................................................... 5 G

(Quadruple Section) ........................................................................................................................................................................................... 3 G

Contact Resistance ........................................................................................................................................................................ 10 milliohms maximum

Shock (Dual Section) ......................................................................................................................................................................................................... 20 G

Rotational Life .....................................................................................................................................................................................................25,000 cycles

Switch Actuating Torque (50% Duty cycle @ Rated Power Load) .................................................................................. 1.41 to 4.94 N-cm (2 to 7 oz.-in.)

Moisture Resistance (MIL-STD-202, Method 106, Condition B)

Contact Resistance (0.1 VDC-10 mA) ............................................................................................................................................ 10 milliohms maximum

Insulation Resistance (After 24 Hours @ Room Temperature) (500 VDC) .................................................................................... 100 megohms minimum

Switch Housing Material ................................................................................................................. High temperature, ﬂ ame retardant, thermosetting plastic

Mechanical Characteristics1

Actuating Torque (Each Section, Switch Module Only) ....................................................................................................... 3.53 to 10.6 N-cm (5 to 15 oz.-in.)

Running Torque (Out of Detent, 2-4 Module Assembly) ..................................................................................................... 0.21 to 1.41 N-cm (0.3 to 2 oz.-in.)

Detent ..................................................................................................................................................................................................... CW or CCW standard

Actuation Angle ...................................................................................................................................................................................................................25 °

Contact Materials ..........................................................................................................................................................................Fine silver with gold overlay

Terminal Styles .................................................................................................................................................................................................. Solder lug only

Standard Orientation ..............................................................................................................................................................In-line with control terminals

Optional .......................................................................................................................................................................... Rotated 90 ° CCW from standard

Terminal Strength (Before and After Soldering Heat Exposure) .......................................................................................................... 0.9 Kg (2 lbs.) minimum

NOTE: Model 81/82 performance speciﬁ cations do not apply to units subjected to printed circuit board cleaning procedures.

1At room ambient: +25 °C nominal and 50 % relative humidity nominal, except as noted.

Rotary Switch Speciﬁ cations

Speciﬁ cations are subject to change without notice.

The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time.

Users should verify actual device performance in their speciﬁ c applications.

81/82 - 5/8 ” Square Single-Turn Panel Control

Product Dimensions

"A" Bushing

3/8 " (9.53 mm) Dia. Plain - Single Shaft

3/8-32 UNEF

"B" Bushing

3/8 " (9.53 mm) Dia. Plain - Single Shaft

3/8-32 UNEF 4.45

(.175)

MIN.

"C" Bushing

1/4 " (6.35 mm) Dia. Plain - Single Shaft

"C" Bushing

1/4 " (6.35 mm) Dia. Plain - Concentric Shaft

3/8-32 UNEF

M10 x 0.75-6g

TRIPLE CONCENTRIC

(SPECIAL ORDER) 1/4-32 UNEF

"A" Bushing

3/8 " (9.53 mm) Dia. Plain - Concentric Shaft

"S" Bushing

10 mm Dia. Locking - Single Shaft

1/4-32 UNEF

"E" Bushing

1/4 " (6.35 mm) Dia. Locking - Single Shaft

9.50 ± .38

(.375 ±.015)

12.7,15.88,19.05,22.23± .79

(1/2, 5/8, 7/8, ± 1/32)

STANDARD

DIA.

(.063+.015/-.000)

SHAFT SLOT 1.19 WIDE X

1.60+.38/-.00 DEEP

(.047)

45 ° ±5 ° X

(.010)

CHAMFER

.25

45 ° ±5 ° X (.010)

CHAMFER

.25

7.92

(.312)MIN.

9.53 ± .13

(.375 ± .005)

PILOT DIA.

5.49 OPTIONAL FLAT 16.00 LONG OR 1.52 FROM

"A" BUSHING END FOR SHAFTS UNDER 17.46

(.216) (.63) (.06)

(11/16)

(.010)

CHAMFER

.25

45 ° ±5 ° X (.010)

CHAMFER

.25

(.063 +.015/-.000)

SHAFT SLOT 1.19 WIDE X

1.60 + .38/- .00 DEEP

(.047)

12.70 ± .13

(.500 ± .005)

15.88 ± .79

(5/8 ± 1/32)

STANDARD

6.32 ± .03

(.249 ± .001) DIA.

9.53 ± .13

(.375 ± .005)

PILOT DIA.

11.13

(.438)

MIN.

6.35 ± .13

(.250 ± .005)

9.53,12.7,15.88,19.05,22.23 ± .79

(3/8, 1/2, 5/8, 3/4, 7/8, ± 1/32)

STANDARD

SHAFT SLOT .79 WIDE X

.79 ± .25 DEEP

(.031)

(.031 ± .010)

2.39 ± .13 OPTIONAL FLAT 6.35 LONG OR 1.52 FROM

"C" BUSHING END FOR SHAFTS UNDER 14.30

(.094 ± . 005) (.250) (.06)

(9/16)

6.35 ± .05

(.250 ± .002)

PILOT DIA.

SHAFT SLOT .78 WIDE X

.78 ± .03 DEEP

(.031)

(.031 ± .001)

12.7 ± .13

(.500 ± .005)

10.80

(.425)

MIN.

15.88 ± .79

(5/8 ± 1/32)

STANDARD

3.18 ± .03

(.125 ± .001) DIA.

6.35 ± .05

(.250 ± .002)

PILOT DIA.

28.58 ± .79

(1-1/8 ± 1/32)

STANDARD

19.05 ± .79

(3/4 ± 1/32)

STANDARD

(.375)

9.53

6.32 ± .03

(.249 ±.001)DIA.

3.162 ± .025

(.1245 ± .001)DIA.

1.98 ± .03

(.078 ± .001)

DIA.

OUTER SHAFT 7.47 DIA. OPERATES SECTION #1 INNER SHAFT

3.18 DIA. OPERATES SECTION #2, #3, & #4 ("G" STYLE)

(.249)

(.125)

OUTER SHAFT 3.18 DIA. OPERATES SECTION #1 INNER SHAFT

.078 DIA. OPERATES SECTION #2, #3, & #4 ("K" STYLE)

(.125)

(1.95)

15.88 ± .79

(5/8 ± 1/32)

STANDARD

25.40 ± .79

(1 ± 1/32)

STANDARD

22.00 ± 0.79

(.866 ± .031)

STANDARD

PILOT DIA.

12.50 ± 0.38

(.492 ± .015)

10.92

(.430)

6.000 +0.000/-0.075

(.236 +.000/-.003)

1.01 ± 0.10

(.040 ± .004)

9.90

(.390)

1.80 ± 0.25

(.071 ± .010)

6.35

(.25)

3.162 ± .025

(.1245 ± .001)DIA.

1.98 ± .03

(.078 ± .001)DIA.

3.162 ± .025

(.1245 ± .001)

DIA.

6.35 ± .03

(1/4 ± 1/32)

1/4-32 UNEF

45 ° ±5 ° X (.010)

CHAMFER

.25

SHAFT SLOT

WIDE X

DEEP

DIA.

MIN.

DIMENSIONS: MM

(INCHES)

CCW

POTENTIOMETER

Speciﬁ cations are subject to change without notice.

The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time.

Users should verify actual device performance in their speciﬁ c applications.

81/82 - 5/8 ” Square Single-Turn Panel Control

Product Dimensions

Dual Unit - PC Pins & J-Hook Triple Unit - PC Pins & J-Hook Quad Unit - PC Pins & J-Hook

FLATTED SHAFT

120 ° ± 5 ° CCW END

Shaft Flat Orientation*

SLOTTED SHAFT

123

30 ° ±5 °

*EXCLUDES MODELS 83 AND 84

Model 81

Suggested PC Board Layout - PC Pins

(Single-Shaft Style Bottom View)

Note: For units with dual concentric shaft styles, a

2.54 (.100) spacer is added between the module(s) driven

by the outer shaft and those driven by the inner shaft.

For G, K, or V shafts, add the spacer between

modules 1 and 2. For L or M shafts, add the spacer

between modules 2 and 3. For N or P shafts, add the

spacer between modules 3 and 4.

Model 81/82

Single Unit - PC Pins & J-Hook

Terminal outlines shown as solid lines represent PC Pins, available

on Model 81. Dashed line terminal outline represents "J" Hook,

available on Model 82.

26.04 ± .79

(1.025 ± .031)

10.16 ± .38

(.400 ± .015)

10.16 ± .38

(.400 ± .015) TYP. 10.16 ± .38

(.400 ± .015) TYP.

36.20 ± 1.19

(1.425 ± .047)

46.36 ± 1.19

(1.825 ± .047)

15.88 ± .41

(.625 ± .016)

5.97 ± .38

(.235 ± .015)

5.08 ± .38

(.200 ± .015)

15.88 ± .38

(.625 ± .015) 11.94

(.470)

9.58 ± .38

(.377 ± .015)

15.88 ± .38

(.625 ± .015)

5.33 ± .76

(.210 ± .03)

3.81

(.150)

MAX. 3 PLCS.

.81

(.032)

DIA.

5.08 ± .38

(.200 ± .015)

12.7

(.50)

1.14

(.045)

DIA.

5.08 ± .13

(.200 ± .005)

10.16 ± .13

(.400 ± .005)

5.08 ± .13

(.200 ± .005)

DIMENSIONS: MM

(INCHES)

85/86 - 5/8 ” Square Single-Turn Panel Control with Rotary Switch

Product Dimensions

REAR

PLATE

COVER

(.725)

18.42

Switch Module

Model 85/86

Primary Potentiometer Module

Model 85/86

Secondary Potentiometer Module

Model 85/86

Locating Lug Options - All Model 80 Series

NOTE: "D" OPTION - NO A/R LUG. OTHER LOCATING LUG OPTIONS AVAILABLE. CONSULT FACTORY FOR DETAILS.

REAR

VERTICAL ORIENTATION

(Types R50, R51, R52 & R53)

HORIZONTAL ORIENTATION

(Types R56, R57, R58 & R59)

COVER

PLATE

SWITCH

MODULE

PRIMARY

POTENTIOMETER

MODULE

Assembly Sequence

Model 85/86

Switch Module Terminal Orientation

Secondary Potentiometer Module

TOLERANCES EXCEPT AS SHOWN: DECIMAL .XXX ± (.005)

.XX ± (.015)

ANGLE ± 5 %

14.53

(.572)

9.58 ± .38

(.377 ± .015)

12.7

(.50)

5.08

(.200)

5.97

(.235)

8.56

(.337)

10.16

(.400)

1.60

(.063)

8.56

(.337)

5.08

(.200)

15.88

(.625)

15.88

(.625)

5.08

(.200)

1.35

(.053)

2.77

(.109)

TYP.

6 PLACES

2.29

(.090)

(.095)L X (.045)W

SLOT TYP. 6 PLACES

2.41 1.14 2.92

(.115)

9.53

(.375)

.127

.38

7.75

(.305)

.46

(.018)

2.31

(.091)

3.18

(.125)

13.49

(.531)

2.36

(.093)

9.53

(.375) .79 ± .41

(.031 ± .016) E = 2.36 ± .76

(.093 ± .03)

H & J = 1.98 ± .41

(.078 ± .016)

FLATTED SHAFT

120 ° ± 5 ° CCW END

Shaft Flat Orientation*

SLOTTED SHAFT

30 ° ± 5 °

*EXCLUDES MODELS 83 AND 84

DPST (NO/NC)

(TYPES 50, 51, 56, 57)

DPST (NO/NO)

(TYPES 52, 53, 58, 59)

Switch contacts shown in detent position.

A7.75

(.305)

.46

(.018)

A E J

7.75

(.305) .46

(.018)

2.31

(.091)

.79 ± .41

(.031 ± .016)

MOUNTING

SURFACE

RECOMMENDED

PANEL LAYOUT

7.75

(.305) 2.49

(.098)

#40 DRILL

DIA.

9.91

(.390) DIA.

DIMENSIONS: MM

(INCHES)

Speciﬁ cations are subject to change without notice.

The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time.

Users should verify actual device performance in their speciﬁ c applications.

81/82 - 5/8 ” Square Single-Turn Panel Control

85/86 - 5/8 ” Square Single-Turn Panel Control with Rotary Switch

How To Order

8 5 A 2 A - B 2 8 - A 1 5 / R51 L

8 1 A 2 A - B 2 8 - A 1 5 / A15 L

ELEMENT TAPER RESISTANCE CODE

TYPE/TOLERANCE VALUE IN OHMS

(A) Linear Cermet ±10 % (05) - 100 (30) - 15 K

(H) Linear Cermet ±5 % (28) - 150 (16) - 20 K

(06) - 200 (17) - 25 K

(07) - 250 (18) - 50 K

(08) - 500 (19) - 75 K

(09) - 750 (20) - 100 K

(10) - 1 K (31) - 150 K

(29) - 1.5 K (21) - 200 K

(11) - 2 K (22) - 250 K

(12) - 2.5 K (23) - 500 K

(13) - 5 K (24) - 750 K

(14) - 7.5 K (25) - 1 M

(15) - 10 K

(B) Linear C-P ±20 % (10) - 1 K (18) - 50 K

(E) Linear C-P ±10 % (12) - 2.5 K (20) - 100 K

(13) - 5 K (22) - 250 K

(15) - 10 K (23) - 500 K

(16) - 20 K (25) - 1 M

(17) - 25 K

(D) CW Audio C-P ±20 % (12) - 2.5 K (20) - 100 K

(F) CCW Audio Cermet ±10 % (13) - 5 K (22) - 250 K

(G) CCW Audio C-P ±20 % (15) - 10 K (23) - 500 K

(S) CW Audio C-P ±10 % (17) - 25 K (25) - 1 M

(T) CCW Audio C-P ± 10 %

AVAILABLE ONLY IN

SHAFT TYPE LENGTHS BUSHINGS

(CODE) (CODE)

A Single Plain 1/4 ” (6.35 mm) D 16,20,24,28 A, B, J

B Single Slotted 1/4 ” (6.35 mm) D 16,20,24,28 A, B, J

C Single Flatted 1/4 ” (6.35 mm) D 20,24,28 A, B, J

E Single Slotted 1/8 ” (3.18 mm) D 12,16,20,24,28 C, E, N

F Single Flatted 1/8 ” (3.18 mm) D 24 C, N

G Dual Concentric Plain 1/4 ” (6.35 mm) D - 1/8 ” (3.18 mm) D 36,40 A, J

Outer Operates Section 1

K Dual Concentric Plain 1/8 ” (3.18 mm) D - 5/64 ” (1.98 mm) D 32,36 C, N

Outer Operates Section 1

L Dual Concentric Plain 1/4 ” (6.35 mm) D - 1/8 ” (3.18 mm) D 36,40 A, J

Outer Operates Section 1/2

M Dual Concentric Plain 1/8 ” (3.18 mm) D - 5/64 ” (1.98 mm) D 32,36 C, N

Outer Operates Section 1/2

N Dual Concentric Plain 1/4 ” (6.35 mm) D - 1/8 ” (3.18 mm) D 36,40 A, J

Outer Operates Section 1/2/3

P Dual Concentric Plain 1/8 ” (3.18 mm) D - 5/64 ” (1.98 mm) D 32,36 C, N

Outer Operates Section 1/2/3

R Single Slotted 6 mm D 16,19,22,50 R, S

T Single Slotted 4 mm D 10, 13, 22 U

V Dual Concentric Plain 6 mm D - 3 mm D 30, 42 R

Outer Operates Section 1

A Plain 3/8 ” (9.53 mm) D x 3/8 ” (9.53 mm) L

B Locking 3/8 ” (9.53 mm) D x 1/2 ” (12.7 mm) L

C Plain 1/4 ” (6.35 mm) D x 1/4 ” (6.35 mm) L

E Locking 1/4 ” (6.35 mm) D x 1/2 ” (12.7 mm) L

J Plain 3/8 ” (9.53 mm) D x 1/4 ” (6.35 mm) L

N Plain 1/4 ” (6.35 mm) D x 3/8 ” (9.53 mm) L

R Plain 10 mm D x 9 mm L

S Locking 10 mm D x 12.5 mm L

U Plain 7 mm D x 6 mm L

MODEL

81 Single-Turn, PC Pins

82 Single-Turn, J-Hooks

85 Single-Turn, Pot/Rotary Switch, PC Pins

86 Single-Turn, Pot/Rotary Switch, J-Hooks

SWITCH TYPE (MODELS 85 & 86 ONLY)

(R50) DPST N.O./N.C. CW Detent In-Line Term

(R51) DPST N.O./N.C. CCW Detent In-Line Term

(R52) DPST N.O./N.O. CW Detent In-Line Term

(R53) DPST N.O./N.O. CCW Detent In-Line Term

(R56) DPST N.O./N.C. CW Detent Horz Term

(R57) DPST N.O./N.C. CCW Detent Horz Term

(R58) DPST N.O./N.O. CW Detent Horz Term

(R59) DPST N.O./N.O. CCW Detent Horz Term

# SECTIONS APPLICABLE MODELS

1 Single 81,82

2 Double 81,82,85,86

3 Triple 81,82,85,86

4 Quad 81,82,85,86

BUSHING

A Single .305 R, 90 °CW

B Double .305 R, 90 ° & 270 °CW

C Single .305 R, 270 °CW

D No Lug

E Single .531 R, 90 °CW

F Single .305 R, 180 °CW

J Single .375 R, 90 °CW

K Double .375 R, 90 ° & 270 °CW

ANTI-ROTATION LUG

RoHS IDENTIFIER

CompliantL

Models 81 & 82: Part number for multiple section

potentiometers must have a taper and resistance value for

each section.

Models 85 & 86: Part number must contain a switch type.

Boldface features are Bourns standard options.

All others are available with higher minimum order

quantities.

SHAFT AVAILABLE

LENGTH ONLY IN

(FMS) BUSHING

Code Description Code

12 3/8 ” L C, N, J

16 1/2 ” L A, C, J, N

20 5/8 ” L A, B, C, E, J, N

24 3/4 ” L A, B, C, E, J, N

28 7/8 ” L A, B, C, E, J, N

32 1 ” L A, B, C, E, J, N

36 1-1/8 ” L A, B, C, E, J, N

40 1-1/4 ” L A, B, C, E, J, N

Metric

10 10 mmL U

13 13 mmL U

16 16 mmL R, S

19 19 mmL R, S

22 22 mmL R, S, U

30 30 mmL R, S

42 42 mmL R, S

50 50 mmL R, S

REV. 11/14

Speciﬁ cations are subject to change without notice.

The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time.

Users should verify actual device performance in their speciﬁ c applications.

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Bourns:

82C1A-E24-E13L 82E1A-E20-A05L 82E1A-E20-E12L 82E1A-E20-E18L 82C1A-E24-E15L 82C1A-E24-S15L

82C1A-E24-E22L 82E1A-E20-E17L 82C1A-E24-B25L 82C1A-E24-S13L 86C2A-E24-E10/R51L 82E1A-E20-E10L

86C2A-E24-E13/R51L 86C2A-E24-S17/R51L 82E1A-E20-E15L 86C2A-E24-B25/R51L 86C2A-E24-E18/R51L

82E1A-E20-E13L 82E1A-E20-B23L 82C1A-E24-A05L 82C1A-E24-A07L 86C2A-E24-A05/R51L 82E1A-E20-E20L

82C1A-E24-S10L 86C2A-E24-E12/R51L 86C2A-E24-E20/R51L 82C1A-E24-S25L 86C2A-E24-B23/R51L 82C1A-

E24-E12L 82C1A-E24-E18L 86C2A-E24-E17/R51L 82C1A-E24-A08L 82C1A-E24-B23L 82C1A-E24-S12L 82C1A-

E24-E17L 82C1A-E24-E10L 86C2A-E24-A08/R51L 86C2A-E24-E15/R51L 82C1A-E24-S18L 82E1A-E20-A08L

82C1A-E24-E20L