INA203 INA204 INA205 INA 203 INA2 03 INA 203 www.ti.com........................................................................................................................................................... SBOS393D - MARCH 2007 - REVISED MAY 2009 Unidirectional Measurement Current-Shunt Monitor with Dual Comparators FEATURES DESCRIPTION 1 * COMPLETE CURRENT SENSE SOLUTION * DUAL COMPARATORS: - Comparator 1 with Latch - Comparator 2 with Optional Delay * COMMON-MODE RANGE: -16V to +80V * HIGH ACCURACY: 3.5% (max) Over Temperature * BANDWIDTH: 500kHz * QUIESCENT CURRENT: 1.8mA * PACKAGES: SO-14, TSSOP-14, MSOP-10 2 APPLICATIONS * * * * * * * NOTEBOOK COMPUTERS CELL PHONES TELECOM EQUIPMENT AUTOMOTIVE POWER MANAGEMENT BATTERY CHARGERS WELDING EQUIPMENT 1 OUT 2 1.2V REF The INA203, INA204, and INA205 also incorporate two open-drain comparators with internal 0.6V references. On 14-pin versions, the comparator references can be overridden by external inputs. Comparator 1 includes a latching capability, and Comparator 2 has a user-programmable delay. 14-pin versions also provide a 1.2V reference output. The INA203, INA204, and INA205 operate from a single +2.7V to +18V supply. They are specified over the extended operating temperature range of -40C to +125C. INA203-INA205 VS 1 10 VIN+ OUT 2 9 VIN- 14 VIN+ CMP1 IN+ 3 8 CMP1 OUT 13 VIN- CMP2 IN+ 4 7 CMP2 OUT GND 5 6 CMP1 RESET INA203-INA205 VS The INA203, INA204, and INA205 are a family of unidirectional current-shunt monitors with voltage output, dual comparators, and voltage reference. The INA203, INA204, and INA205 can sense drops across shunts at common-mode voltages from -16V to +80V. The INA203, INA204, and INA205 are available with three output voltage scales: 20V/V, 50V/V, and 100V/V, with up to 500kHz bandwidth. CMP1 IN-/0.6V REF 3 12 1.2V REF OUT CMP1 IN+ 4 11 CMP1 OUT CMP2 IN+ 5 10 CMP2 OUT CMP2 IN-/0.6V REF 6 9 CMP2 DELAY GND 7 8 CMP1 RESET 0.6V REF MSOP-10 DEVICE GAIN INA203 20V/V INA204 50V/V INA205 100V/V SO-14, TSSOP-14 RELATED PRODUCTS FEATURES PRODUCT Variant of INA203-INA205 Comparator 2 polarity INA206-INA208 Current-shunt monitor with single Comparator and VREF INA200-INA202 Current-shunt monitor only INA193-INA198 Current-shunt monitor with split stages for filter options INA270-INA271 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2007-2009, Texas Instruments Incorporated INA203 INA204 INA205 SBOS393D - MARCH 2007 - REVISED MAY 2009........................................................................................................................................................... www.ti.com This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. ORDERING INFORMATION (1) PACKAGE DESIGNATOR PACKAGE MARKING 1.2V REF OUT EXTERNAL COMP1 AND COMP2 REF INPUTS X X INTERNAL COMP1 AND COMP2 0.6V REF COMP2 DELAY PIN X X PRODUCT GAIN PACKAGELEAD SO-14 D INA203A INA203 20V/V MSOP-10 DGS BQN TSSOP-14 PW INA203A X X X X X X X X INA204 INA205 (1) X SO-14 D INA204A MSOP-10 DGS BQO TSSOP-14 PW INA204A X X X X X X X X 50V/V SO-14 D INA205A MSOP-10 DGS BQP TSSOP-14 PW INA205A 100V/V X X X X X X For the most current package and ordering information see the Package Option Addendum at the end of this document, or see the TI web site at www.ti.com. ABSOLUTE MAXIMUM RATINGS (1) INA203, INA204, INA205 UNIT Supply Voltage, V+ 18 V Differential (VIN+) - (VIN-) -18 to +18 V Common-Mode -16 to +80 V Comparator Analog Input and Reset Pins GND - 0.3 to (V+) + 0.3 V Analog Output, Out Pin Current-Shunt Monitor Analog Inputs, VIN+and VIN- GND - 0.3 to (V+) + 0.3 V Comparator Output, Out Pin GND - 0.3 to 18 V VREF and CMP2 Delay Pin GND - 0.3 to 10 V Input Current Into Any Pin 5 mA Operating Temperature -55 to +150 C Storage Temperature -65 to +150 C Junction Temperature ESD Ratings (1) 2 +150 C Human Body Model (HBM) 4000 V Charged Device Model (CDM) 500 V Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those specified is not supported. Submit Documentation Feedback Copyright (c) 2007-2009, Texas Instruments Incorporated Product Folder Link(s): INA203 INA204 INA205 INA203 INA204 INA205 www.ti.com........................................................................................................................................................... SBOS393D - MARCH 2007 - REVISED MAY 2009 ELECTRICAL CHARACTERISTICS: CURRENT-SHUNT MONITOR Boldface limits apply over the specified temperature range: TA = -40C to +125C. At TA = +25C, VS = +12V, VCM = +12V, VSENSE = 100mV, RL = 10k to GND, RPULL-UP = 5.1k each connected from CMP1 OUT and CMP2 OUT to VS, and CMP1 IN+ = 1V and CMP2 IN- = GND, unless otherwise noted. INA203, INA204, INA205 CURRENT-SHUNT MONITOR PARAMETERS CONDITIONS MIN TYP MAX UNIT 0.15 (VS - 0.25)/Gain V INPUT Full-Scale Sense Input Voltage Common-Mode Input Range Common-Mode Rejection Ratio VSENSE VSENSE = VIN+ - VIN- VCM -16 CMRR Over Temperature Offset Voltage, RTI (1) VCM = -16V to +80V 80 VCM = +12V to +80V 100 VOS 80 -40C to +25C vs Power Supply Input Bias Current, VIN- Pin dB 123 0.5 +25C to +125C vs Temperature V 100 dB 2.5 mV 3 mV 3.5 dVOS/dT PSR mV V/C TMIN to TMAX 5 VOUT = 2V, VCM = +18V, 2.7V 2.5 100 V/V 9 16 A IB OUTPUT (VSENSE 20mV) Gain: G INA203 20 V/V INA204 50 V/V INA205 100 Gain Error VSENSE = 20mV to 100mV Over Temperature VSENSE = 20mV to 100mV Total Output Error (2) VSENSE = 120mV, VS = +16V Over Temperature 0.75 VSENSE = 120mV, VS = +16V Nonlinearity Error (3) Output Impedance, Pin 2 0.2 VSENSE = 20mV to 100mV % 2 % 2.2 % 3.5 % 0.002 % 1.5 No Sustained Oscillation 10 nF -16V VCM < 0V 300 RO Maximum Capacitive Load V/V 1 OUTPUT (VSENSE < 20mV) (4) INA203, INA204, INA205 mV INA203 0V VCM VS, VS = 5V 0.4 V INA204 0V VCM VS, VS = 5V 1 V INA205 0V VCM VS, VS = 5V VS < VCM 80V INA203, INA204, INA205 2 V 300 mV VOLTAGE OUTPUT (5) Output Swing to the Positive Rail VIN- = 11V, VIN+ = 12V (V+) - 0.15 (V+) - 0.25 V Output Swing to GND (6) VIN- = 0V, VIN+ = -0.5V (VGND) + 0.004 (VGND) + 0.05 V INA203 CLOAD = 5pF 500 kHz INA204 CLOAD = 5pF 300 kHz INA205 CLOAD = 5pF 200 kHz Phase Margin CLOAD < 10nF 40 Degrees 1 V/s 2 s 40 nV/Hz FREQUENCY RESPONSE Bandwidth: Slew Rate Settling Time (1%) BW SR VSENSE = 10mVPP to 100mVPP, CLOAD = 5pF NOISE, RTI Output Voltage Noise Density (1) (2) (3) (4) (5) (6) Offset is extrapolated from measurements of the output at 20mV and 100mV VSENSE. Total output error includes effects of gain error and VOS. Linearity is best fit to a straight line. For details on this region of operation, see the Accuracy Variations section in the Applications Information. See Typical Characteristic curve Positive Output Voltage Swing vs Output Current (Figure 8). Specified by design; not production tested. Copyright (c) 2007-2009, Texas Instruments Incorporated Product Folder Link(s): INA203 INA204 INA205 Submit Documentation Feedback 3 INA203 INA204 INA205 SBOS393D - MARCH 2007 - REVISED MAY 2009........................................................................................................................................................... www.ti.com ELECTRICAL CHARACTERISTICS: COMPARATOR Boldface limits apply over the specified temperature range: TA = -40C to +125C. At TA = +25C, VS = +12V, VCM = +12V, VSENSE = 100mV, RL = 10k to GND, and RPULL-UP = 5.1k each connected from CMP1 OUT and CMP2 OUT to VS, unless otherwise noted. INA203, INA204, INA205 COMPARATOR PARAMETERS CONDITIONS MIN TYP MAX UNIT OFFSET VOLTAGE Offset Voltage Comparator Common-Mode Voltage = Threshold Voltage Offset Voltage Drift, Comparator 1 Offset Voltage Drift, Comparator 2 2 mV 2 V/C V/C +5.4 Threshold TA = +25C 590 Over Temperature 608 586 Hysteresis (1), CMP1 (1) Hysteresis , CMP2 620 mV 625 mV TA = -40C to +85C -8 mV TA = -40C to +85C 8 mV INPUT BIAS CURRENT (2) CMP1 IN+, CMP2 IN+ 0.005 vs Temperature 10 nA 15 nA INPUT IMPEDANCE Pins 3 and 6 (14-pin packages only) 10 k CMP1 IN+ and CMP2 IN+ 0V to VS - 1.5V V Pins 3 and 6 (14-pin packages only) (3) 0V to VS - 1.5V V INPUT RANGE OUTPUT CMP VOUT 1V to 4V, RL 15k Connected to 5V 200 High-Level Output Current VID = 0.4V, VOH = VS 0.0001 1 A Low-Level Output Voltage VID = -0.6V, IOL = 2.35mA 220 300 mV Comparator 1 RL to 5V, CL = 15pF, 100mV Input Step with 5mV Overdrive 1.3 s Comparator 2 RL to 5V, CL = 15pF, 100mV Input Step with 5mV Overdrive, CDELAY Pin Open 1.3 s Large-Signal Differential Voltage Gain V/mV RESPONSE TIME (4) RESET RESET Threshold (5) Logic Input Impedance Minimum RESET Pulse Width RESET Propagation Delay Comparator 2 Delay Equation (6) Comparator 2 Delay (1) (2) (3) (4) (5) (6) tD CDELAY = 0.1F 1.1 V 2 M 1.5 s 3 s CDELAY = tD/5 F 0.5 s Hysteresis refers to the threshold (the threshold specification applies to a rising edge of a noninverting input) of a falling edge on the noninverting input of the comparator; refer to Figure 1. Specified by design; not production tested. See the Comparator Maximum Input Voltage Range section in the Applications Information. The comparator response time specified is the interval between the input step function and the instant when the output crosses 1.4V. The CMP1 RESET input has an internal 2M (typical) pull-down. Leaving the CMP1 RESET open results in a LOW state, with transparent comparator operation. The Comparator 2 delay applies to both rising and falling edges of the comparator output. VTHRESHOLD 0.592 0.6 Input Voltage Hysteresis = VTHRESHOLD - 8mV Figure 1. Comparator Hysteresis 4 Submit Documentation Feedback Copyright (c) 2007-2009, Texas Instruments Incorporated Product Folder Link(s): INA203 INA204 INA205 INA203 INA204 INA205 www.ti.com........................................................................................................................................................... SBOS393D - MARCH 2007 - REVISED MAY 2009 ELECTRICAL CHARACTERISTICS: REFERENCE Boldface limits apply over the specified temperature range: TA = -40C to +125C. At TA = +25C, VS = +12V, VCM = +12V, VSENSE = 100mV, RL = 10k to GND, and RPULL-UP = 5.1k each connected from CMP1 OUT and CMP2 OUT to VS, unless otherwise noted. INA203, INA204, INA205 REFERENCE PARAMETERS CONDITIONS MIN TYP MAX UNIT 1.188 1.2 1.212 V 40 100 ppm/C REFERENCE VOLTAGE 1.2VREFOUT Output Voltage Reference Drift dVOUT/dT TA = -40C to +85C 0.6VREF Output Voltage (Pins 3 and 6 of 14-pin packages only) Reference Drift 0.6 dVOUT/dT LOAD REGULATION V TA = -40C to +85C 40 100 ppm/C 0mA < ISOURCE < 0.5mA 0.4 2 mV/mA 0mA < ISINK < 0.5mA 0.4 mV/mA 1 mA 2.7V < VS < 18V 30 V/V No Sustained Oscillations 10 nF 10 k dVOUT/dILOAD Sourcing Sinking LOAD CURRENT ILOAD LINE REGULATION dVOUT/dVS CAPACITIVE LOAD Reference Output Maximum Capacitive Load OUTPUT IMPEDANCE Pins 3 and 6 of 14-Pin Packages Only ELECTRICAL CHARACTERISTICS: GENERAL Boldface limits apply over the specified temperature range: TA = -40C to +125C. All specifications at TA = +25C, VS = +12V, VCM = +12V, VSENSE = 100mV, RL = 10k to GND, RPULL-UP = 5.1k each connected from CMP1 OUT and CMP2 OUT to VS, and CMP1 IN+ = 1V and CMP2 IN- = GND, unless otherwise noted. INA203, INA204, INA205 GENERAL PARAMETERS CONDITIONS MIN TYP MAX UNIT POWER SUPPLY Operating Power Supply Quiescent Current VS IQ Over Temperature +2.7 VOUT = 2V 1.8 VSENSE = 0mV Comparator Power-On Reset Threshold (1) +18 V 2.2 mA 2.8 mA 1.5 V TEMPERATURE Specified Temperature Range -40 +125 C Operating Temperature Range -55 +150 C Storage Temperature Range -65 +150 C Thermal Resistance (1) JA MSOP-10 Surface-Mount 200 C/W SO-14, TSSOP-14 Surface-Mount 150 C/W The INA203, INA204, and INA205 are designed to power-up with the comparator in a defined reset state as long as CMP1 RESET is open or grounded. The comparator will be in reset as long as the power supply is below the voltage shown here. The comparator assumes a state based on the comparator input above this supply voltage. If CMP1 RESET is high at power-up, the comparator output comes up high and requires a reset to assume a low state, if appropriate. Copyright (c) 2007-2009, Texas Instruments Incorporated Product Folder Link(s): INA203 INA204 INA205 Submit Documentation Feedback 5 INA203 INA204 INA205 SBOS393D - MARCH 2007 - REVISED MAY 2009........................................................................................................................................................... www.ti.com TYPICAL CHARACTERISTICS All specifications at TA = +25C, VS = +12V, VCM = +12V, and VSENSE = 100mV, unless otherwise noted. GAIN vs FREQUENCY 45 G = 50 35 Gain (dB) 30 G = 100 40 G = 50 35 Gain (dB) CLOAD = 1000pF G = 100 40 GAIN vs FREQUENCY 45 G = 20 25 20 30 20 15 15 10 10 5 5 10k 100k G = 20 25 CLOAD = 0 10k 1M 100k Frequency (Hz) Figure 2. Figure 3. GAIN PLOT COMMON-MODE AND POWER-SUPPLY REJECTION vs FREQUENCY 20 140 18 130 Common-Mode and Power-Supply Rejection (dB) 100V/V 16 VOUT (V) 14 50V/V 12 10 8 20V/V 6 4 CMR 110 100 90 PSR 80 70 60 40 0 20 100 200 300 400 500 600 700 800 900 10 100 1k 10k 100k VSENSE (mV) Frequency (Hz) Figure 4. Figure 5. TOTAL OUTPUT ERROR vs VSENSE TOTAL OUTPUT ERROR vs COMMON-MODE VOLTAGE 4.0 0.1 3.5 0.09 3.0 Total Output Error (%) Total Output Error (% error of the ideal output value) 120 50 2 2.5 2.0 1.5 1.0 0.08 0.07 0.06 0.05 0.04 0.03 0.02 0.5 0.01 0 0 50 100 150 200 250 300 350 400 450 500 0 -16 -12 -8 -4 VSENSE (mV) Submit Documentation Feedback 0 4 8 12 16 20 ... 76 80 Common-Mode Voltage (V) Figure 6. 6 1M Frequency (Hz) Figure 7. Copyright (c) 2007-2009, Texas Instruments Incorporated Product Folder Link(s): INA203 INA204 INA205 INA203 INA204 INA205 www.ti.com........................................................................................................................................................... SBOS393D - MARCH 2007 - REVISED MAY 2009 TYPICAL CHARACTERISTICS (continued) All specifications at TA = +25C, VS = +12V, VCM = +12V, and VSENSE = 100mV, unless otherwise noted. POSITIVE OUTPUT VOLTAGE SWING vs OUTPUT CURRENT QUIESCENT CURRENT vs OUTPUT VOLTAGE 3.5 12 11 VS = 12V 10 2.5 +25C 8 -40C +125C 7 6 VS = 3V 5 Sourcing Current +25C 4 -40C Output stage is designed to source current. Current sinking capability is approximately 400mA. 3 2 1 +125C 0 0 IQ (mA) Output Voltage (V) 3.0 Sourcing Current 9 2.0 1.5 1.0 0.5 0 5 10 20 15 25 30 0 1 2 Output Current (mA) 5 7 9 10 9.5 10.5 11.5 17 18 6 8 Figure 8. Figure 9. QUIESCENT CURRENT vs COMMON-MODE VOLTAGE OUTPUT SHORT-CIRCUIT CURRENT vs SUPPLY VOLTAGE 34 VSENSE = 100mV 1.75 VS = 2.7V VS = 12V 1.50 IQ (mA) 4 Output Voltage (V) Output Short-Circuit Current (mA) 2.00 3 1.25 VS = 12V 1.00 VS = 2.7V VSENSE = 0mV 0.75 0.50 -16 -12 -8 -4 -40C 30 +25C 26 +125C 22 18 14 10 6 0 4 8 12 16 20 24 28 32 36 2.5 3.5 4.5 VCM (V) 5.5 6.5 7.5 8.5 Supply Voltage (V) Figure 10. Figure 11. STEP RESPONSE STEP RESPONSE G = 20 Output Voltage (50mV/div) Output Voltage (500mV/div) G = 20 VSENSE = 10mV to 20mV VSENSE = 10mV to 100mV Time (2ms/div) Time (2ms/div) Figure 12. Figure 13. Copyright (c) 2007-2009, Texas Instruments Incorporated Product Folder Link(s): INA203 INA204 INA205 Submit Documentation Feedback 7 INA203 INA204 INA205 SBOS393D - MARCH 2007 - REVISED MAY 2009........................................................................................................................................................... www.ti.com TYPICAL CHARACTERISTICS (continued) All specifications at TA = +25C, VS = +12V, VCM = +12V, and VSENSE = 100mV, unless otherwise noted. STEP RESPONSE STEP RESPONSE G = 50 Output Voltage (50mV/div) Output Voltage (100mV/div) G = 20 VSENSE = 90mV to 100mV VSENSE = 10mV to 20mV Time (2ms/div) Time (5ms/div) Figure 14. Figure 15. STEP RESPONSE STEP RESPONSE G = 50 Output Voltage (1V/div) Output Voltage (100mV/div) G = 50 VSENSE = 90mV to 100mV VSENSE = 10mV to 100mV Time (5ms/div) Time (5ms/div) Figure 16. Figure 17. STEP RESPONSE COMPARATOR VOL vs ISINK 600 G = 100 Output Voltage (2V/div) 500 VOL (mV) 400 300 200 100 VSENSE = 10mV to 100mV 0 Time (10ms/div) 0 1 2 3 4 5 6 ISINK (mA) Figure 18. 8 Submit Documentation Feedback Figure 19. Copyright (c) 2007-2009, Texas Instruments Incorporated Product Folder Link(s): INA203 INA204 INA205 INA203 INA204 INA205 www.ti.com........................................................................................................................................................... SBOS393D - MARCH 2007 - REVISED MAY 2009 TYPICAL CHARACTERISTICS (continued) All specifications at TA = +25C, VS = +12V, VCM = +12V, and VSENSE = 100mV, unless otherwise noted. COMPARATOR TRIP POINT vs SUPPLY VOLTAGE COMPARATOR TRIP POINT vs TEMPERATURE 600 602 Comparator Trip Point (mV) Comparator Trip Point (mV) 599 598 597 596 595 594 593 592 601 600 599 598 597 591 596 590 2 4 6 8 10 12 14 16 18 -25 -50 0 Supply Voltage (V) 25 50 75 100 125 Temperature (C) Figure 20. Figure 21. COMPARATOR 1 PROPAGATION DELAY vs OVERDRIVE VOLTAGE COMPARATOR 2 PROPAGATION DELAY vs OVERDRIVE VOLTAGE 200 14 Propagation Delay (ms) Propagation Delay (ns) 175 150 125 100 13 12 11 75 50 10 0 20 40 60 80 100 120 140 160 180 0 200 20 40 80 100 120 140 160 180 200 Overdrive Voltage (mV) Figure 22. Figure 23. COMPARATOR RESET VOLTAGE vs SUPPLY VOLTAGE COMPARATOR 1 PROPAGATION DELAY vs TEMPERATURE 1.2 300 1.0 275 Propagation Delay (ns) Reset Voltage (V) Overdrive Voltage (mV) 60 0.8 0.6 0.4 0.2 250 225 200 175 150 0 2 4 6 8 10 12 14 16 18 125 -50 -25 Supply Voltage (V) 0 25 50 75 100 125 Temperature (C) Figure 24. Figure 25. Copyright (c) 2007-2009, Texas Instruments Incorporated Product Folder Link(s): INA203 INA204 INA205 Submit Documentation Feedback 9 INA203 INA204 INA205 SBOS393D - MARCH 2007 - REVISED MAY 2009........................................................................................................................................................... www.ti.com TYPICAL CHARACTERISTICS (continued) All specifications at TA = +25C, VS = +12V, VCM = +12V, and VSENSE = 100mV, unless otherwise noted. COMPARATOR 2 PROPAGATION DELAY vs CAPACITANCE COMPARATOR 1 PROPAGATION DELAY Propagation Delay (ms) 1000 100 Input 200mV/div 10 1 Output 2V/div 0.1 VOD = 5mV 0.01 0.001 0.01 0.1 1 10 2ms/div 100 Delay Capacitance (nF) Figure 26. Figure 27. COMPARATOR 2 PROPAGATION DELAY REFERENCE VOLTAGE vs TEMPERATURE 1.22 Input 200mV/div VREF (V) 1.21 Output 2V/div 1.20 1.19 VOD = 5mV 5ms/div 1.18 -50 -25 0 25 50 75 100 125 Temperature (C) Figure 28. 10 Submit Documentation Feedback Figure 29. Copyright (c) 2007-2009, Texas Instruments Incorporated Product Folder Link(s): INA203 INA204 INA205 INA203 INA204 INA205 www.ti.com........................................................................................................................................................... SBOS393D - MARCH 2007 - REVISED MAY 2009 APPLICATIONS INFORMATION BASIC CONNECTIONS Power-supply bypass capacitors are required for stability. Applications with noisy or high-impedance power supplies may require additional decoupling capacitors to reject power-supply noise. Connect bypass capacitors close to the device pins. This section addresses the accuracy of these specific operating regions: * Normal Case 1: VSENSE 20mV, VCM VS * Normal Case 2: VSENSE 20mV, VCM < VS * Low VSENSE Case 1: VSENSE < 20mV, -16V VCM <0 * Low VSENSE Case 2: VSENSE < 20mV, 0V VCM VS * Low VSENSE Case 3: VSENSE < 20mV, VS < VCM 80V POWER SUPPLY Normal Case 1: VSENSE 20mV, VCM VS The input circuitry of the INA203, INA204, and INA205 can accurately measure beyond the power-supply voltage, V+. For example, the V+ power supply can be 5V, whereas the load power-supply voltage is up to +80V. The output voltage range of the OUT terminal, however, is limited by the voltages on the power-supply pin. This region of operation provides the highest accuracy. Here, the input offset voltage is characterized and measured using a two-step method. First, the gain is determined by Equation 1. VOUT1 - VOUT2 G= 100mV - 20mV (1) Figure 30 shows the basic connections of the INA203, INA204, and INA205. The input pins, VIN+ and VIN-, should be connected as closely as possible to the shunt resistor to minimize any resistance in series with the shunt resistance. where: ACCURACY VARIATIONS AS A RESULT OF VSENSE AND COMMON-MODE VOLTAGE VOUT1 = Output Voltage with VSENSE = 100mV VOUT2 = Output Voltage with VSENSE = 20mV The accuracy of the INA203, INA204, and INA205 current shunt monitors is a function of two main variables: VSENSE (VIN+ - VIN-) and common-mode voltage, VCM, relative to the supply voltage, VS. VCM is expressed as (VIN+ + VIN-)/2; however, in practice, VCM is seen as the voltage at VIN+ because the voltage drop across VSENSE is usually small. Then the offset voltage is measured at VSENSE = 100mV and referred to the input (RTI) of the current shunt monitor, as shown in Equation 2. VOUT1 VOSRTI (Referred-To-Input) = - 100mV G (2) RSHUNT 3mW Load Supply -18V to +80V Load 5V Supply VS Current Shunt Monitor Output CBYPASS 0.01mF INA203 x20 OUT 1.2V REF CMP1 IN-/0.6 REF CMP1 IN+ VIN+ VIN- RPULL-UP 4.7kW RPULL-UP 4.7kW 1.2V REF OUT CMP1 OUT CMP2 IN+ CMP2 IN-/0.6 REF CMP2 OUT CMP2 DELAY GND CMP1 RESET Optional Delay Capacitor 0.2mF Transparent/Reset Latch Figure 30. INA20x Basic Connection Copyright (c) 2007-2009, Texas Instruments Incorporated Product Folder Link(s): INA203 INA204 INA205 Submit Documentation Feedback 11 INA203 INA204 INA205 SBOS393D - MARCH 2007 - REVISED MAY 2009........................................................................................................................................................... www.ti.com Normal Case 2: VSENSE 20mV, VCM < VS This region of operation has slightly less accuracy than Normal Case 1 as a result of the common-mode operating area in which the part functions, as seen in the Output Error vs Common-Mode Voltage curve (Figure 7). As noted, for this graph VS = 12V; for VCM < 12V, the Output Error increases as VCM becomes less than 12V, with a typical maximum error of 0.005% at the most negative VCM = -16V. Low VSENSE Case 1: VSENSE < 20mV, -16V VCM < 0; and Low VSENSE Case 3: VSENSE < 20mV, VS < VCM 80V Although the INA203 family of devices are not designed for accurate operation in either of these regions, some applications are exposed to these conditions; for example, when monitoring power supplies that are switched on and off while VS is still applied to the INA203, INA204, or INA205. It is important to know what the behavior of the devices will be in these regions. As VSENSE approaches 0mV, in these VCM regions, the device output accuracy degrades. A larger-than-normal offset can appear at the current shunt monitor output with a typical maximum value of VOUT = 300mV for VSENSE = 0mV. As VSENSE approaches 20mV, VOUT returns to the expected output value with accuracy as specified in the Electrical Characteristics. Figure 31 illustrates this effect using the INA205 (Gain = 100). 12 Submit Documentation Feedback 2.0 1.8 1.6 1.4 VOUT (V) In the Typical Characteristics, the Output Error vs Common-Mode Voltage curve (Figure 7) shows the highest accuracy for this region of operation. In this plot, VS = 12V; for VCM 12V, the output error is at its minimum. This case is also used to create the VSENSE 20mV output specifications in the Electrical Characteristics table. 1.2 Actual 1.0 0.8 Ideal 0.6 0.4 0.2 0 0 2 4 6 8 10 12 14 16 18 20 VSENSE (mV) Figure 31. Example for Low VSENSE Cases 1 and 3 (INA205, Gain = 100) Low VSENSE Case 2: VSENSE < 20mV, 0V VCM VS This region of operation is the least accurate for the INA203 family. To achieve the wide input common-mode voltage range, these devices use two op amp front ends in parallel. One op amp front end operates in the positive input common-mode voltage range, and the other in the negative input region. For this case, neither of these two internal amplifiers dominates and overall loop gain is very low. Within this region, VOUT approaches voltages close to linear operation levels for Normal Case 2. This deviation from linear operation becomes greatest the closer VSENSE approaches 0V. Within this region, as VSENSE approaches 20mV, device operation is closer to that described by Normal Case 2. Figure 32 illustrates this behavior for the INA205. The VOUT maximum peak for this case is tested by maintaining a constant VS, setting VSENSE = 0mV, and sweeping VCM from 0V to VS. The exact VCM at which VOUT peaks during this test varies from part to part, but the VOUT maximum peak is tested to be less than the specified VOUT Tested Limit. Copyright (c) 2007-2009, Texas Instruments Incorporated Product Folder Link(s): INA203 INA204 INA205 INA203 INA204 INA205 www.ti.com........................................................................................................................................................... SBOS393D - MARCH 2007 - REVISED MAY 2009 2.4 2.2 INA205 VOUT Tested Limit (1) VCM1 2.0 Ideal 1.8 VCM2 VOUT (V) 1.6 1.4 VCM3 1.2 1.0 0.8 VOUT Tested Limit at VSENSE = 0mV, 0 VCM1 VS. VCM4 0.6 VCM2, VCM3, and VCM4 illustrate the variance from part to part of the VCM that can cause maximum VOUT with VSENSE < 20mV. 0.4 0.2 0 0 2 4 6 8 10 12 14 16 18 20 22 24 VSENSE (mV) NOTE: (1) INA203 VOUT Tested Limit = 0.4V. INA204 VOUT Tested Limit = 1V. Figure 32. Example for Low VSENSE Case 2 (INA205, Gain = 100) SELECTING RSHUNT The value chosen for the shunt resistor, RSHUNT, depends on the application and is a compromise between small-signal accuracy and maximum permissible voltage loss in the measurement line. High values of RSHUNT provide better accuracy at lower currents by minimizing the effects of offset, while low values of RSHUNT minimize voltage loss in the supply line. For most applications, best performance is attained with an RSHUNT value that provides a full-scale shunt voltage range of 50mV to 100mV. Maximum input voltage for accurate measurements is (VSHUNT - 0.25)/Gain. TRANSIENT PROTECTION The -16V to +80V common-mode range of the INA203, INA204, and INA205 is ideal for withstanding automotive fault conditions ranging from 12V battery reversal up to +80V transients, since no additional protective components are needed up to those levels. In the event that the INA203, INA204, and INA205 are exposed to transients on the inputs in excess of their ratings, then external transient absorption with semiconductor transient absorbers (zeners or Transzorbs) are necessary. Use of metal oxide varistors (MOVs) or video disk recorders (VDRs) is not recommended except when they are used in addition to a semiconductor transient absorber. Select the transient absorber such that it will never allow the INA203, INA204, and INA205 to be exposed to transients greater than +80V (that is, allow for transient absorber tolerance, as well as additional voltage because of transient absorber dynamic impedance). Despite the use of internal zener-type ESD protection, the INA203, INA204, and INA205 do not lend themselves to using external resistors in series with the inputs because the internal gain resistors can vary up to 30% but are closely matched. (If gain accuracy is not important, then resistors can be added in series with the INA203, INA204, and INA205 inputs with two equal resistors on each input.) OUTPUT VOLTAGE RANGE The output of the INA203, INA204, and INA205 is accurate within the output voltage swing range set by the power-supply pin, V+. This performance is best illustrated when using the INA205 (a gain of 100 version), where a 100mV full-scale input from the shunt resistor requires an output voltage swing of +10V, and a power-supply voltage sufficient to achieve +10V on the output. INPUT FILTERING An obvious and straightforward location for filtering is at the output of the INA203, INA204, and INA205 series; however, this location negates the advantage of the low output impedance of the internal buffer. The only other option for filtering is at the input pins of the INA203, INA204, and INA205, which is complicated by the internal 5k + 30% input impedance; this configuration is illustrated in Figure 33. Using the lowest possible resistor values minimizes both the initial shift in gain and effects of tolerance. The effect on initial gain is given by Equation 3: Gain Error % = 100 - 100 5kW 5kW + RFILT (3) Total effect on gain error can be calculated by replacing the 5k term with 5k - 30%, (or 3.5k) or 5k + 30% (or 6.5k). The tolerance extremes of RFILT can also be inserted into the equation. If a pair of 100 1% resistors are used on the inputs, the initial gain error will be 1.96%. Worst-case tolerance conditions will always occur at the lower excursion of the internal 5k resistor (3.5k), and the higher excursion of RFILT - 3% in this case. Copyright (c) 2007-2009, Texas Instruments Incorporated Product Folder Link(s): INA203 INA204 INA205 Submit Documentation Feedback 13 INA203 INA204 INA205 SBOS393D - MARCH 2007 - REVISED MAY 2009........................................................................................................................................................... www.ti.com RSHUNT << RFILTER 3mW VSUPPLY Load RFILTER < 100W RFILTER <100W CFILTER INA203-INA205 VIN+ VS 1 14 OUT 2 13 CMP1 IN-/0.6V REF 3 CMP1 IN+ 4 11 CMP1 OUT CMP2 IN+ 5 10 CMP2 OUT CMP2 IN-/0.6V REF 6 9 CMP2 DELAY GND 7 8 CMP1 RESET 1.2V REF VIN- 12 1.2V REF OUT f-3dB f-3dB = 1 2p(2RFILTER)CFILTER SO-14, TSSOP-14 Figure 33. Input Filter (Gain Error: 1.5% to -2.2%) Note that the specified accuracy of the INA203, INA204, and INA205 must then be combined in addition to these tolerances. While this discussion treated accuracy worst-case conditions by combining the extremes of the resistor values, it is appropriate to use geometric mean or root sum square calculations to total the effects of accuracy variations. The 14-pin versions of the INA203, INA204, and INA205 include additional features for comparator functions. The comparator reference voltage of both Comparator 1 and Comparator 2 can be overridden by external inputs for increased design flexibility. Comparator 2 has a programmable delay. COMPARATOR DELAY (14-Pin Version Only) REFERENCE The INA203, INA204, and INA205 include an internal voltage reference that has a load regulation of 0.4mV/mA (typical), and not more than 100ppm/C of drift. Only the 14-pin package allows external access to reference voltages, where voltages of 1.2V and 0.6V are both available. Output current versus output voltage is illustrated in the Typical Characteristics section. COMPARATOR The INA203, INA204, and INA205 devices incorporate two open-drain comparators. These comparators typically have 2mV of offset and a 1.3s (typical) response time. The output of Comparator 1 latches and is reset through the CMP1 RESET pin, as shown in Figure 35. This configuration applies to both the 10- and 14-pin versions. Figure 34 illustrates the comparator delay. 14 Submit Documentation Feedback The Comparator 2 programmable delay is controlled by a capacitor connected to the CMP2 Delay Pin; see Figure 30. The capacitor value (in F) is selected by using Equation 4: t CDELAY (in mF) = D 5 (4) A simplified version of the delay circuit for Comparator 2 is shown in Figure 34. The delay comparator consists of two comparator stages with the delay between them. Note that I1 and I2 cannot be turned on simultaneously; I1 corresponds to a U1 low output and I2 corresponds to a U1 high output. Using an initial assumption that the U1 output is low, I1 is on, then U2 +IN is zero. If U1 goes high, I2 supplies 120nA to CDELAY. The voltage at U2 +IN begins to ramp toward a 0.6V threshold. When the voltage crosses this threshold, the U2 output goes high while the voltage at U2 +IN continues to ramp up to a maximum of 1.2V when given sufficient time (twice the value of the delay specified for CDELAY). This entire sequence is reversed when the comparator outputs go low, so that returning to low exhibits the same delay. Copyright (c) 2007-2009, Texas Instruments Incorporated Product Folder Link(s): INA203 INA204 INA205 INA203 INA204 INA205 www.ti.com........................................................................................................................................................... SBOS393D - MARCH 2007 - REVISED MAY 2009 1.2V I2 120nA U1 U2 I1 120nA 0.6V CDELAY Figure 34. Simplified Model of the Comparator 2 Delay Circuit 0.6V VIN 0V CMP Out RESET Figure 35. Comparator Latching Capability It is important to note what will happen if events occur more rapidly than the delay timeout; for example, when the U1 output goes high (turning on I2), but returns low (turning I1 back on) prior to reaching the 0.6V transition for U2. The voltage at U2 +IN ramps back down at a rate determined by the value of CDELAY, and only returns to zero if given sufficient time. whether either or both inputs are subject to the large voltage. When making this determination, consider the 20k from each input back to the comparator. Figure 37 shows the maximum input voltage that avoids creating a reference error when driving both inputs (an equivalent resistance back into the reference of 10k). 1mA In essence, when analyzing Comparator 2 for behavior with events more rapid than its delay setting, use the model shown in Figure 34. COMPARATOR MAXIMUM INPUT VOLTAGE RANGE The maximum voltage at the comparator input for normal operation is up to (V+) - 1.5V. There are special considerations when overdriving the reference inputs (pins 3 and 6). Driving either or both inputs high enough to drive 1mA back into the reference introduces errors into the reference. Figure 36 shows the basic input structure. A general guideline is to limit the voltage on both inputs to a total of 20V. The exact limit depends on the available voltage and 1.2V 20kW 20kW CMP1 IN- CMP2 IN+ Figure 36. Limit Current Into Reference 1mA Copyright (c) 2007-2009, Texas Instruments Incorporated Product Folder Link(s): INA203 INA204 INA205 Submit Documentation Feedback 15 INA203 INA204 INA205 SBOS393D - MARCH 2007 - REVISED MAY 2009........................................................................................................................................................... www.ti.com RSHUNT 3mW Load Supply -18V to +80V Load 5V Supply VS Current Shunt Monitor Output CMP1 IN-/0.6 REF CBYPASS 0.01mF V < 11.2 VIN+ VIN- INA203 x20 OUT 1.2V REF RPULL-UP 4.7kW RPULL-UP 4.7kW 1.2V REF OUT CMP1 IN+ CMP1 OUT CMP2 IN+ CMP2 IN- CMP2 OUT CMP2 DELAY GND CMP1 RESET Optional Delay Capacitor 0.2mF Transparent/Reset Latch Figure 37. Overdriving Comparator Inputs Without Generating a Reference Error Raychem Polyswitch Load < 18V Battery +5V Supply VS+ x20 OUT CMP1 IN- 1.2V REF 3.3kW Pull-Up Resistors VIN+ INA203 VIN1.2V REF OUT CMP1 IN+ CMP1 OUT CMP2 IN+ CMP2 IN- CMP2 OUT CMP2 DELAY GND CMP1 RESET CBYPASS 0.01mF Overlimit Warning (1) (1) Reset Latch Optional CDELAY 0.01mF NOTE: (1) Warning at half current (with optional delay). Overlimit latches when Polyswitch opens. Figure 38. Polyswitch Warning and Fault Detection Circuit 16 Submit Documentation Feedback Copyright (c) 2007-2009, Texas Instruments Incorporated Product Folder Link(s): INA203 INA204 INA205 INA203 INA204 INA205 www.ti.com........................................................................................................................................................... SBOS393D - MARCH 2007 - REVISED MAY 2009 RSHUNT 0.02W Load Q2 NDS8434A R1 100kW +5V Supply R7 1kW VS+ R5 100kW R6 6.04kW R3 14kW R4 6.04kW CMP1 IN- VIN+ INA203 x20 OUT 1.2V REF Q1 2N3904 VIN- CMP1 IN+ CMP1 OUT CMP2 IN+ CMP2 IN- CMP2 OUT CMP2 DELAY GND CMP1 RESET CBYPASS 0.01mF R2 1kW 1.2V REF OUT Reset Latch Figure 39. Lead-Acid Battery Protection Circuit Copyright (c) 2007-2009, Texas Instruments Incorporated Product Folder Link(s): INA203 INA204 INA205 Submit Documentation Feedback 17 INA203 INA204 INA205 SBOS393D - MARCH 2007 - REVISED MAY 2009........................................................................................................................................................... www.ti.com Revision History NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision C (October 2007) to Revision D ............................................................................................... Page * 18 Changed Figure 1 ................................................................................................................................................................. 4 Submit Documentation Feedback Copyright (c) 2007-2009, Texas Instruments Incorporated Product Folder Link(s): INA203 INA204 INA205 PACKAGE OPTION ADDENDUM www.ti.com 3-Dec-2010 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) Samples (Requires Login) INA203AID ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Purchase Samples INA203AIDG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Purchase Samples INA203AIDGSR ACTIVE MSOP DGS 10 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Request Free Samples INA203AIDGSRG4 ACTIVE MSOP DGS 10 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Request Free Samples INA203AIDGST ACTIVE MSOP DGS 10 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Purchase Samples INA203AIDGSTG4 ACTIVE MSOP DGS 10 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Purchase Samples INA203AIDR ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Purchase Samples INA203AIDRG4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Purchase Samples INA203AIPW ACTIVE TSSOP PW 14 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Purchase Samples INA203AIPWG4 ACTIVE TSSOP PW 14 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Purchase Samples INA203AIPWR ACTIVE TSSOP PW 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Purchase Samples INA203AIPWRG4 ACTIVE TSSOP PW 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Purchase Samples INA204AID ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Purchase Samples INA204AIDG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Purchase Samples INA204AIDGSR ACTIVE MSOP DGS 10 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR Request Free Samples INA204AIDGSRG4 ACTIVE MSOP DGS 10 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR Request Free Samples INA204AIDGST ACTIVE MSOP DGS 10 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Addendum-Page 1 Purchase Samples PACKAGE OPTION ADDENDUM www.ti.com 3-Dec-2010 Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) Samples (Requires Login) INA204AIDGSTG4 ACTIVE MSOP DGS 10 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Purchase Samples INA204AIDR ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Purchase Samples INA204AIDRG4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Purchase Samples INA204AIPW ACTIVE TSSOP PW 14 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Purchase Samples INA204AIPWG4 ACTIVE TSSOP PW 14 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Purchase Samples INA204AIPWR ACTIVE TSSOP PW 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Purchase Samples INA204AIPWRG4 ACTIVE TSSOP PW 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Purchase Samples INA205AID ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Purchase Samples INA205AIDG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Purchase Samples INA205AIDGSR ACTIVE MSOP DGS 10 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Request Free Samples INA205AIDGSRG4 ACTIVE MSOP DGS 10 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Request Free Samples INA205AIDGST ACTIVE MSOP DGS 10 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Purchase Samples INA205AIDGSTG4 ACTIVE MSOP DGS 10 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Purchase Samples INA205AIDR ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Purchase Samples INA205AIDRG4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Purchase Samples INA205AIPW ACTIVE TSSOP PW 14 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Purchase Samples INA205AIPWG4 ACTIVE TSSOP PW 14 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Purchase Samples INA205AIPWR ACTIVE TSSOP PW 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Purchase Samples Addendum-Page 2 PACKAGE OPTION ADDENDUM www.ti.com Orderable Device INA205AIPWRG4 3-Dec-2010 Status (1) ACTIVE Package Type Package Drawing TSSOP PW Pins 14 Package Qty 2000 Eco Plan (2) Green (RoHS & no Sb/Br) Lead/ Ball Finish MSL Peak Temp (3) CU NIPDAU Level-2-260C-1 YEAR Samples (Requires Login) Purchase Samples (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing INA203AIDGSR MSOP DGS 10 INA203AIDGST MSOP DGS INA203AIDR SOIC D INA203AIPWR TSSOP INA204AIDGSR SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 10 250 180.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 PW 14 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 MSOP DGS 10 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 INA204AIDGST MSOP DGS 10 250 180.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 INA204AIDR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 INA204AIPWR TSSOP PW 14 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 INA205AIDGSR MSOP DGS 10 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 INA205AIDGST MSOP DGS 10 250 180.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 INA205AIDR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 INA205AIPWR TSSOP PW 14 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) INA203AIDGSR MSOP DGS 10 2500 367.0 367.0 35.0 INA203AIDGST MSOP DGS 10 250 210.0 185.0 35.0 INA203AIDR SOIC D 14 2500 367.0 367.0 38.0 INA203AIPWR TSSOP PW 14 2000 367.0 367.0 35.0 INA204AIDGSR MSOP DGS 10 2500 367.0 367.0 35.0 INA204AIDGST MSOP DGS 10 250 210.0 185.0 35.0 INA204AIDR SOIC D 14 2500 367.0 367.0 38.0 INA204AIPWR TSSOP PW 14 2000 367.0 367.0 35.0 INA205AIDGSR MSOP DGS 10 2500 367.0 367.0 35.0 INA205AIDGST MSOP DGS 10 250 210.0 185.0 35.0 INA205AIDR SOIC D 14 2500 367.0 367.0 38.0 INA205AIPWR TSSOP PW 14 2000 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated