The TIP30 Series power transistors are designed for use in general purpose amplifier and switching applications. Features: e Designed for complementary use with TIP29 series @ 30W at 25C case temperature -1A continuous collector current e -3A peak collector current Minimum fT of 3 MHz at 10V, 0.02A e Customer-specified selections available Designed for power amplifier and high-speed switching applications maximum ratings (Tc = 25C) (unless otherwise noted) PNP POWER TRANSISTORS COMPLEMENTARY TO THE TIP29 SERIES TIP 30 Series -40 ~ -100 VOLTS -1 AMP, 30 WATTS i BASE CASE STYLE TO-220AB DIMENSIONS ARE IN INCHES AND (MILLIMETERS) PNP COLLECTOR EMITTER 1612.95: aio. 28 nee 9044.09) 0511.20 38019. 17014. 32)| of be Sa ~048(T. _ - .265(6.73 t -245(6.22} . CASE ' TEMPERATURE REFERENCE POINT + .355(9,02 145(3.68 S558 28) "41(a.58)0'*- | \ 2015.80 + 006(0.15) A F, -130(3.3} afte Qsio 8 TERM. 500(12.7)MEN. TERM2 9551.99) A 1. TERMS Vo .033(0.84) 105(2.67 \ 107(2.72 027(0.69) tesa M O87(2-21) .055(1.39 * 210(5.33 021(0.53) Sasttaa) + EE aes 076(0-38) [tee [terw.1 | Term.2 | Terms | Tap | [T0-220-AB | BASE | courector [ emitrer | coLtector | RATING SYMBOL TIP30 TIP30A TIP30B TIP30C UNITS Collector-Emitter Voltage VcEO -40 ~60 -80 -100 Volts Collector-Base Voltage VcoBo -80 -100 -120 -140 -Volts Emitter Base Voltage VEBO -5 -5 5 -5 Volts Collector Current Continuous Ic -1 -1 -1 -1 A Peak Iom -3 -3 3 -3 Base Current Continuous Ip -0.4 -0.4 -0.4 -0.4 A Total Power Dissipation @ Ta = 25C Pp 2 2 2 2 Watts @ To = 26C 30 30 30 30 Operating and Storage Junction Temperature Range Ty, Tsta | ~65 to +150 | -65to +150 { -65to+150 | -65 to +150 C thermal characteristics Thermal Resistance, Junction to Case Rec 4.17 4.17 4.17 4.17 C/W Maximum Lead Temperature for Soldering Purposes: % from Case for 5 Seconds TL 250 250 250 250 C 775 electrical characteristics (To = 25C) (unless otherwise specified) | CHARACTERISTIC | symBo.| MIN | TYP | MAX | UNIT | off characteristics Collector-Emitter Breakdown Voltage TIP30 VcEO ~40 _ _ Volts (Ic = -30mA) TIP30A -60 _ _ TIP30B ~80 _ TIP30C -100 _ _ Collector Cutoff Current IcEO (VcE = -30V) TIP30, TIP30A -0.3 mA (VcE = -60V) TIP30B, TIP30C _ 03 Collector Cutoff Current IcES (VcE = -80V) TIP3O = -0.2 mA (VceE = -100V) TIP30A ~ -0.2 (VGE = -120V) TIP30B _ -0.2 (VCE = -140V) TIP30C _ _ -0.2 Emitter Cutoff Current (Vep = -5V, Ic = 0) |EBO _ ~ a mA second breakdown | Second Breakdown with Base Forward Biased FBSOA | SEE FIGURE 3 on characteristics DC Current Gain here (Ic = -0.2A, Vog = -4V) 20 _ (Ic = 1A, Voce = 4V) 15 _ 75 Collector-Emitter Saturation Voltage VcE(sat) (Io = -1A, Ig = -125mA) = = -0.7 Vv Base-Emitter Voltage VBE(on) (Ic = ~1A, Voge = -4V) _ _ -1.3 Vv switching characteristics Turn-on Time Ri = 300, Ic = -1A ton 0.3 _ us lpi = Ipa =0.1A Turn-off Time VBE (ott) = 4.3V toff _ 1 _ INPUT MONITOR ouTeuT i MONITOR 1INO14 INPUT 43 V 10% Laem MONITOR 9 V Von=-8.5V 80% ' AA { WwW P>t+_Pt 4 567 1NO914 1N914 1N914 i 1 1 ' ' 1 ' 1 270 pF tone et bet tott poy t DL) Veen I t 302 OUTPUT 90% \ MONITOR 10% Vepi = 10V ADJUST FOR VOLTAGE WAVEFORMS Von =~ 85 VAT INPUT MONITOR TEST CIRCUIT NOTES: A. Vgen is a 30-V pulse into a 50 2 termination. ap moo . The Vgen waveform is supplied by the following characteristics: t, < 15ns, t< 15ns, Zoye = 502 tw = 20us, duty cycle 2%. . Waveforms are monitored on an oscilloscope with the following characteristics: t, < 15/ns, Rig, = 10 MQ, Cin, < 11.5 pF. . Resistors must be noninductive types. . The d-c power supplies may require additional bypassing in order to minimize ringing. FIGURE 1. RESISTIVE-LOAD SWITCHING 776 STATIC FORWARD CURRENT TRANSFER RATIO vs COLLECTOR CURRENT Ik z rere 400 c 2c : Notes 5 and 6 ~ 100 5 & 40 ) z e 10 uu. a4 3 4 | WwW Le a | 0.001 - 0.01 -0.1 ~1 ICollector Current-A FIGURE 2. TYPICAL CHARACTERISTICS NOTES: 5. These parameters must be measured using pulse techniques, tw = 300 us, duty cycle < 2%. 6. These parameters are measured with voitage-sensing contacts separate from the current-carrying contacts. FORWARD-BIAS SAFE OPERATING AREA 100 40 tw = us, d= 0.1 ty = Tms, d= 0.1 = 10% ty = 10 ms, d= 0.1 = 10% $ 10 OC Operation, See Note 7 $4 3 oO = 04 g TIP3OA\ 5 TIP30B = 0. TIP30C 0.04 0.01 1 4 10 40 100 400 1000 VeECollector-Emitter VoltageV FIGURE 3 MAXIMUM SAFE OPERATING AREA NOTE 7: This combination of maximum voltage and current values may be achieved only when switching from saturation to cutoff with a clamped inductive load. DISSIPATION DERATING CURVE Q 26 50 75 100 125 150 Tco-Case TemperatureC FIGURE4 THERMAL INFORMATION 777