To learn more about ON Semiconductor, please visit our website at
www.onsemi.com
Please note: As part of the Fairchild Semiconductor integration, some of the Fairchild orderable part numbers
will need to change in order to meet ON Semiconductor’s system requirements. Since the ON Semiconductor
product management systems do not have the ability to manage part nomenclature that utilizes an underscore
(_), the underscore (_) in the Fairchild part numbers will be changed to a dash (-). This document may contain
device numbers with an underscore (_). Please check the ON Semiconductor website to verify the updated
device numbers. The most current and up-to-date ordering information can be found at www.onsemi.com. Please
email any questions regarding the system integration to Fairchild_questions@onsemi.com.
Is Now Part of
ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number
of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right
to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON
Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON
Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s
technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA
Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended
or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, afliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out
of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor
is an Equal Opportunity/Afrmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
FNA41560 / FNA41560B2 Motion SPM® 45 Series
January 2014
©2011 Fairchild Semiconductor Corporation 1www.fairchildsemi.com
FNA41560 / FNA41560B2 Rev. C3
FNA41560 / FNA41560B2
Motion SPM® 45 Series
Features
UL Certified No. E209204 (UL1557)
600 V - 15 A 3-Phase IGBT Inverter with Integral Gate
Drivers and Protection
Low Thermal Resistance Using Ceramic Substrate
Low-Loss, Short-Circuit Rated IGBTs
Built-In Bootstrap Diodes and De dicated Vs Pins Sim-
plify PCB Layout
Built-In NTC Thermistor for Temperature Monitoring
Separate Open-Emitter Pins from Low-Side IGBTs for
Three-Phase Current Sensing
Single-Grounded Power Supply
Optimized for 5 kHz Switching Frequency
Isolation Rating: 2000 Vrms / min.
Applications
Motion Control - Home Appliance / Industrial Motor
Related Resources
AN-9070 - Motion SPM® 45 Series Users Gui de
AN-9071 - Motion SPM® 45 Series Thermal Perfor-
mance Information
AN-9072 - Motion SPM® 45 Series Mounting Guid-
ance
RD-344 - Reference Design (Three Shunt Solution)
RD-345 - Reference Design (One Shunt Solution)
General Description
FNA41560 / FNA41560B2 is a Motion SPM ® 45 module
providing a fully-featured, high-performance inverter out-
put stage for AC Induction, BLDC, and PMSM motors.
These modules integrate optimized gate drive of
the built-in IGBTs to minimize EMI and losses, while also
providing multiple on-module protection features includ-
ing under-voltage lockouts, over-current shutdown, ther-
mal monitoring, and fault reporting. The built-in, high-
speed HVIC requires only a single supply voltage and
translates the incoming logic-level gate inputs to the
high-voltage, high-current drive si gnals required to prop-
erly drive the module's robust short-circuit-rated IGBTs.
Separate negative IGBT terminals are availabl e for each
phase to support the widest variety of control algorithms.
Package Mark ing and Ordering Information
Figure 1. Package Overview
Device Device Marking Package Packing Type Quantity
FNA41560 FNA41560 SPMAA-A26 Rail 12
FNA41560B2 FNA41560B2 SPMAA-C26 Rail 12
FNA41560 / FNA41560B2 Rev. C3
FNA41560 / FNA41560B2 Motion SPM® 45 Series
©2011 Fairchild Semiconductor Corporation 2www.fairchildsemi.com
Integrated Power Functions
600 V - 15 A IGBT inverter for three-phase DC / AC power conversion (please refer to Figure 3)
Integrated Drive, Protection, and System Control Functions
For inverter high-side IGBTs: gate drive circuit, high-voltage isolated high-speed level shifting
control circuit Under-Voltage Lock-Out (UVLO) protection
For inverter low-side IGBTs: gate drive circuit, Short-Circuit Protection (SCP)
control supply circuit Under-Voltage Lock-Out (UVLO) protection
Fault signaling: corresponding to UVLO (low-side supply) and SC faults
Input interface: active-HIGH interface, works with 3.3 / 5 V logic, Schmitt trigger input
Pin Configuration
Figure 2. Top View
VTH(1)
RTH(2)
P(3)
U(4)
V(5)
W(6)
NU(7)
NV(8)
NW(9)
VB(U)(26)
VS(U)(25)
VB(V)(24)
VS(V)(23)
VB(W)(22)
VS(W)(21)
IN(UH)(20)
IN(VH)(19)
IN(WH)(18)
VCC(H)(17)
COM(15)
IN(UL)(14)
IN(VL)(13)
IN(WL)(12)
VFO(11)
CSC(10)
VCC(L)(16)
Ca se Temperatu re ( TC)
Detecting Point
VTH(1)
RTH(2)
P(3)
U(4)
V(5)
W(6)
NU(7)
NV(8)
NW(9)
VB(U)(26)
VS(U)(25)
VB(V)(24)
VS(V)(23)
VB(W)(22)
VS(W)(21)
IN(UH)(20)
IN(VH)(19)
IN(WH)(18)
VCC(H)(17)
COM(15)
IN(UL)(14)
IN(VL)(13)
IN(WL)(12)
VFO(11)
CSC(10)
VCC(L)(16)
Ca se Temperatu re ( TC)
Detecting Point
FNA41560 / FNA41560B2 Motion SPM® 45 Series
©2011 Fairchild Semiconductor Corporation 3www.fairchildsemi.com
FNA41560 / FNA41560B2 Rev. C3
Pin Descriptions
Pin Number Pin Name Pin Description
1V
TH Thermistor Bias Voltage
2R
TH Series Resistor for the Use of Thermistor (Temperature Detection)
3 P Positive DC-Link Input
4 U Output for U-Phase
5 V Output for V-Phase
6 W Output for W-Phase
7N
UNegative DC-Link Input for U-Phase
8N
VNegative DC-Link Input for V-Phase
9N
WNegative DC-Link Input for W-Phase
10 CSC Capacitor (Low-Pass Filter) for Short-circuit Current Detection Input
11 VFO Fault Output
12 IN(WL) Signal Input for Low-Side W-Phase
13 IN(VL) Signal Input for Low-Side V-Phase
14 IN(UL) Signal Input for Low-Side U-Phase
15 COM Common Supply Ground
16 VCC(L) Low-Side Common Bias Voltage for IC and IGBTs Driving
17 VCC(H) High-Side Common Bias Voltage for IC and IGBTs Driving
18 IN(WH) Signal Input for High-Side W-Phase
19 IN(VH) Signal Input for High-Side V-Phase
20 IN(UH) Signal Input for High-Side U-Phase
21 VS(W) High-Side Bias Voltage Ground for W-Phase IGBT Driving
22 VB(W) High-Side Bias Voltage for W-Phase IGBT Driving
23 VS(V) High-Side Bias Voltage Ground for V-Phase IGBT Driving
24 VB(V) High-Side Bias Voltage for V-Phase IGBT Driving
25 VS(U) High-Side Bias Voltage Ground for U-Phase IGBT Driving
26 VB(U) High-Side Bias Voltage for U-Phase IGBT Driving
FNA41560 / FNA41560B2 Motion SPM® 45 Series
©2011 Fairchild Semiconductor Corporation 4www.fairchildsemi.com
FNA41560 / FNA41560B2 Rev. C3
Internal Equivalent Circuit and Input/Output Pins
Figure 3. Internal Block Diagram
1st Notes:
1. Inverter high-side is composed of three IGBTs, freewheeling diodes, and one control IC for each IGBT.
2. Inverter low-side is composed of three IGBTs, freewheeling diodes, and one control IC for each IGBT. It has gate drive and protection functions.
3. Inverter power side is composed of four inverter DC-link input terminals and three inverter output terminals.
COM
VCC
IN(WL)
IN(VL)
IN(UL)
VFO
C(SC) OUT(WL)
OUT(VL)
OUT(UL)
NW(9)
NV(8)
NU(7)
W(6)
V (5)
U(4)
P (3)
(25) VS(U)
(26) VB(U)
(23) VS(V)
(24) VB(V)
(10) CSC
(11) VFO
(12) IN(WL)
(13) IN(VL)
(14) IN(UL)
(15) COM
UVB
OUT(UH)
UVS
IN(UH)
WVS
WVS
OUT(WH)
IN(WH)
COM
VCC
WVB
OUT(VH)
VVS
IN(VH)
VTH (1)
(19) IN(VH)
(20) IN(UH)
(21) VS(W)
(22) VB(W)
(17) VCC(H)
(18) IN(WH)
RTH (2)
Thermister
UVS
VVS
VVB
(16) VCC(L)
FNA41560 / FNA41560B2 Motion SPM® 45 Series
©2011 Fairchild Semiconductor Corporation 5www.fairchildsemi.com
FNA41560 / FNA41560B2 Rev. C3
Absolute Maximum Ratings (TJ = 25°C, unless otherwise specified.)
Inverter Part
2nd Notes:
1. The maximum junction temperature rating of the power chips integrated within the Motion SPM® 45 product is 150C.
Control Part
Bootstrap Diode Part
Total System
Thermal Resistance
2nd Notes:
2. For the measurement point of case temperature (TC), please refer to Figure 2.
Symbol Parameter Conditions Rating Unit
VPN Supply Voltage Applied between P - NU, NV, NW450 V
VPN(Surge) Supply Voltage (Surge) Applied between P - NU, NV, NW500 V
VCES Collector - Emitter Voltage 600 V
± ICEach IGBT Collector Current TC = 25°C, TJ 150°C 15 A
± ICP Each IGBT Collector Current (Peak) TC = 25°C, TJ 150°C, Under 1 ms Pulse
Width 30 A
PCCollector Dissipation TC = 25°C per Chip 41 W
TJOperating Junction Temperature (2nd Note 1) - 40 ~ 150 °C
Symbol Parameter Conditions Rating Unit
VCC Control Supply Voltage Applied between VCC(H), VCC(L) - COM 20 V
VBS High - Side Control Bias Voltage Applied between VB(U) - VS(U), VB(V) - VS(V),
VB(W) - VS(W)
20 V
VIN Input Signal Voltage Applied between IN(UH), IN(VH), IN(WH),
IN(UL), IN(VL), IN(WL) - COM -0.3 ~ VCC + 0.3 V
VFO Fault Output Supply Voltage Applied between VFO - COM -0.3 ~ VCC + 0.3 V
IFO Fault Output Current Sink Current at VFO pin 1 mA
VSC Current-Sensing Input Voltage Applied between CSC - COM -0.3 ~ VCC + 0.3 V
Symbol Parameter Conditions Rating Unit
VRRM Maximum Repetitive Reverse Voltage 600 V
IFForward Current TC = 25°C, TJ 150°C 0.50 A
IFP Forward Current (Peak) TC = 25°C, TJ 150°C, Under 1 ms Pulse
Width 1.50 A
TJOperating Junction Temperature -40 ~ 150 °C
Symbol Parameter Conditions Rating Unit
VPN(PROT) Self-Protection Supply Voltage Limit
(Short-Circuit Protection Capability) VCC = VBS = 13.5 ~ 16.5 V
TJ = 150°C, Non-Repetitive, < 2 s400 V
TSTG Storage Temperature -40 ~ 125 °C
VISO Isolation Voltage 60 Hz, Sinusoidal, AC 1 Minute, Connect
Pins to Heat Sink Plate 2000 Vrms
Symbol Parameter Conditions Min. Typ. Max. Unit
Rth(j-c)Q Junction to Case Thermal Resistance Inverter IGBT Part (per 1 / 6 module) - - 3.0 °C / W
Rth(j-c)F Inverter FWDi Part (per 1 / 6 module) - - 4.3 °C / W
FNA41560 / FNA41560B2 Motion SPM® 45 Series
©2011 Fairchild Semiconductor Corporation 6www.fairchildsemi.com
FNA41560 / FNA41560B2 Rev. C3
Electrical Characteristics (TJ = 25°C, unless otherwise specified.)
Inverter Part
2nd Notes:
3. tON and tOFF include the prop ag ation delay of the internal drive IC. tC(ON) and tC(OFF) are the switching time of IGBT itself under the given gate driving condition internally. For
the detailed information, please see Figure 4.
Figure 4. Switching Time Definition
Symbol Parameter Conditions Min. Typ. Max. Unit
VCE(SAT) Collector - Emitter Saturation
Voltage VCC = VBS = 15 V
VIN = 5 V IC = 15 A, TJ = 25°C - 1.8 2.3 V
VFFWDi Forward Voltage VIN = 0 V IF = 15 A, TJ = 25°C - 1.8 2.3 V
HS tON Switching Times VPN = 300 V, VCC = VBS = 15 V, IC = 15 A
TJ = 25°C
VIN = 0 V 5 V, Inductive Load
(2nd Note 3)
0.45 0.75 1.25 s
tC(ON) -0.250.50s
tOFF -0.751.25s
tC(OFF) -0.250.50s
trr -0.15- s
LS tON VPN = 300 V, VCC = VBS = 15 V, IC = 15 A
TJ = 25°C
VIN = 0 V 5 V, Inductive Load
(2nd Note 3)
0.45 0.75 1.25 s
tC(ON) -0.250.50s
tOFF -0.751.25s
tC(OFF) -0.250.50s
trr -0.15- s
ICES Collector - Emitter Leakage
Current VCE = VCES --1mA
VCE IC
VIN
tON tC(ON)
VIN(ON)
10% IC
10% VCE
90% IC
100% IC
trr
100% IC
VCE
IC
VIN
tOFF tC(OFF)
VIN(OFF) 10% VCE 10% IC
(a ) tu rn -o n (b ) turn -off
FNA41560 / FNA41560B2 Motion SPM® 45 Series
©2011 Fairchild Semiconductor Corporation 7www.fairchildsemi.com
FNA41560 / FNA41560B2 Rev. C3
Figure 5. Switching Loss Characteristics (Typical)
Control Part
2nd Notes:
4. Short-ci rcuit protection is functioning only at the low-sides.
5. TTH is the temperature of thermister itselt. To know case temperature (TC), please make the experiment considering your application.
Symbol Parameter Conditions Min. Typ. Max. Unit
IQCCH Quiescent VCC Supply
Current VCC(H) = 15 V, IN(UH,VH,WH) = 0 V VCC(H) - COM - - 0.10 mA
IQCCL VCC(L) = 15 V, IN(UL,VL, WL) = 0 V VCC(L) - COM - - 2.65 mA
IPCCH Operating VCC Supply
Current VCC(L) = 15 V, fPWM = 20 kHz, duty
= 50%, Applied to One PWM Sig-
nal Input for High-Side
VCC(H) - COM - - 0.15 mA
IPCCL VCC(L) = 15 V, fPWM = 20 kHz, duty
= 50%, Applied to One PWM Sig-
nal Input for Low-Side
VCC(L) - COM - - 3.65 mA
IQBS Quiescent VBS Supply
Current VBS = 15 V, IN(UH, VH, WH) = 0 V VB(U) - VS(U), VB(V) -
VS(V), VB(W) - VS(W)
- - 0.30 mA
IPBS Operating VBS Supply
Current VCC = VBS = 15 V, fPWM = 20 kHz,
Duty = 50%, Applied to One PWM
Signal Input for High-Side
VB(U) - VS(U), VB(V) -
VS(V), VB(W) - VS(W)
- - 2.00 mA
VFOH Fault Output Voltage VSC = 0 V, VFO Circuit: 10 k to 5 V Pull-up 4.5 - - V
VFOL VSC = 1 V, VFO Circuit: 10 k to 5 V Pull-up - - 0.5 V
VSC(ref) Short-Circuit
Current Trip Level VCC = 15 V (2nd Note 4) 0.45 0.50 0.55 V
UVCCD Supply Circuit
Under-Voltage
Protection
Detection level 10.5 - 13.0 V
UVCCR Reset level 11.0 - 13.5 V
UVBSD Detection level 10.0 - 12.5 V
UVBSR Reset level 10.5 - 13.0 V
tFOD Fault-Out Pulse Width 30 - - s
VIN(ON) ON Threshold Voltage Applied between IN(UH), IN(VH), IN(WH), IN(UL), IN(VL),
IN(WL) - COM --2.6V
VIN(OFF) OFF Threshold Voltage 0.8 - - V
RTH Resistance of
Thermister @TTH = 25°C, (2nd Note 5) - 47 - k
@TTH = 100°C - 2.9 - k
0246810121416
0
100
200
300
400
500
600
700
800
900 Indu ctive Load, VPN=300V, VCC=15V, TJ=150
IG BT T urn -ON , Eon
IGBT Tu rn-OFF, Eoff
FRD Turn-OFF, Erec
SWITCHING LOSS, ESW [uJ]
COLLECTOR CURRENT, Ic [A MPE R ES]
0246810121416
0
100
200
300
400
500
600
700
800
900 Inductive Load, VPN=300V, VCC=15V, TJ=25
IG BT T u r n-O N, Eon
IGBT Tu rn-OFF, Eoff
FRD Turn-OFF, Erec
SWITCHING LOSS, ESW [uJ]
COLLECTOR CURRENT, Ic [AMPERES]
FNA41560 / FNA41560B2 Motion SPM® 45 Series
©2011 Fairchild Semiconductor Corporation 8www.fairchildsemi.com
FNA41560 / FNA41560B2 Rev. C3
Figure. 6. R-T Curve of The Built-In Thermistor
Bootstrap Diode Part
Figure 7. Built-In Bootstrap Diode Characteristic
2nd Notes:
6. Built-in bootstrap diode inclu des around 15 resistance characteristic.
Symbol Parameter Conditions Min. Typ. Max. Unit
VFForward Voltage IF = 0.1 A, TC = 25°C - 2.5 - V
trr Reverse-Recovery Time IF = 0.1 A, TC = 25°C - 80 - ns
50 60 70 80 90 100 110 120
0
4
8
12
16
20
Resistance[k]
Temperature [ ]
R-T Curve in 50 ~ 125℃℃
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0 Built-In Bootstrap Diode VF-IF C haracteristic
TC=25oC
IF [A]
VF [V]
FNA41560 / FNA41560B2 Motion SPM® 45 Series
©2011 Fairchild Semiconductor Corporation 9www.fairchildsemi.com
FNA41560 / FNA41560B2 Rev. C3
Recommended Operating Conditions
2nd Notes:
7. This product might not make response if input pulse width is less than the recommanded value.
Figure 8. Allowable Maximum Output Current
2nd Notes:
8. This allowable output curren t value is the referenc e data for the safe operation of this product. This may be different from the actual application and operating condition.
Symbol Parameter Conditions Min. Typ. Max. Unit
VPN Supply Voltage Applied between P - NU, NV, NW- 300 400 V
VCC Control Supply Voltage Applied between VCC(H), VCC(L) - COM 13.5 15.0 16.5 V
VBS High-Side Bias Voltage Applied between VB(U) - VS(U), VB(V) - VS(V), VB(W) -
VS(W)
13.0 15.0 18.5 V
dVCC / d t,
dVBS / dt Control Supply Variation -1 - 1 V / s
tdead Blanking Time for
Preventing Arm-Short For each input signal 1.5 - - s
fPWM PWM Input Signal - 40C TJ 150°C - - 20 kHz
VSEN Voltage for Current
Sensing Applied between NU, NV, NW - COM
(Including Surge-Voltage) -4 4 V
PWIN(ON) Minimun Input Pulse
Width (2nd Note 7) 0.5 - - s
PWIN(OFF) 0.5 - -
0 102030405060708090100110120130140
0
1
2
3
4
5
6
7
8
9
10
11
12
13 Allowable Maximum O utput Current
VDC=300V, VCC=VBS=15V
TJ 150 , TC 125
M.I.=0.9 , P.F.=0.8
Sinusoidal PWM
fSW=15kHz
fSW=5kHz
IOrms [Arms]
Case Temperature, TC []
FNA41560 / FNA41560B2 Motion SPM® 45 Series
©2011 Fairchild Semiconductor Corporation 10 www.fairchildsemi.com
FNA41560 / FNA41560B2 Rev. C3
Mechanical Characteristics and Ratings
Figure 9. Flatness Measurement Position
Figure 10. Mounting Screws Tor que Order
2nd Notes:
9. Do not make over torque when mounting screws. Much mounting torque may cause ceramic cracks, as well as bolts and Al heat-sink destruction.
10. Avoid one side tightening stress. Figure 10 shows the recommended torque order for mounting screws. Uneven mounting can cause the ceramic substrate of the SPM® 45
package to be damage d. The pr e- scr ewi ng torq ue is set to 20 ~ 30% of maximum tor qu e ra ti ng .
Parameter Conditions Min. Typ. Max. Unit
Device Flatness See Figure 9 0 - + 120 m
Mounting Torque Mounting Screw: M3
See Figure 10
Recommended 0.7 N • m 0.6 0.7 0.8 N • m
Recommended 7.1 kg • cm 6.2 7.1 8.1 kg • cm
Weight - 11.00 - g
1
2
Pre - Screwing : 12
Final Screwing : 21
1
2
Pre - Screwing : 12
Final Screwing : 21
FNA41560 / FNA41560B2 Motion SPM® 45 Series
©2011 Fairchild Semiconductor Corporation 11 www.fairchildsemi.com
FNA41560 / FNA41560B2 Rev. C3
Time Charts of Protective Function
a1 : Control supply voltage rises: after the voltage rises UVCCR, the circuits start to operate when next input is applied.
a2 : Normal operation: IGBT ON and carrying current.
a3 : Under-voltage detection (UVCCD).
a4 : IGBT OFF in spite of control input condition.
a5 : Fault output operation starts.
a6 : Under-voltage reset (UVCCR).
a7 : Normal operation: IGBT ON and carrying current.
Figure 11. Under-Voltage Protection (Low-Side)
b1 : Control supply voltage rises: after the voltage reaches UVBSR, the circuits start to operate when next input is applied.
b2 : Normal operation: IGBT ON and carrying current.
b3 : Under-voltage detection (UVBSD).
b4 : IGBT OFF in spite of control input condition, but there is no fault output signal.
b5 : Under-voltage reset (UVBSR).
b6 : Normal operation: IGBT ON and carrying current.
Figure 12. Under-Voltage Protection (High-Side)
Input Signal
Output Current
Fault Output Signal
Control
Supply Voltage
RESET
UVCCR
Protection
Circuit State SET RESET
UVCCD
a1 a3
a2 a4
a6
a5
a7
Input Signal
Output Current
Fault Output Signal
Control
Supply Voltage
RESET
UVBSR
Protection
Circuit State SET RESET
UVBSD
b1 b3
b2 b4 b6
b5
High-level (no fault output)
FNA41560 / FNA41560B2 Motion SPM® 45 Series
©2011 Fairchild Semiconductor Corporation 12 www.fairchildsemi.com
FNA41560 / FNA41560B2 Rev. C3
(with the external shunt resistance and CR connection)
c1 : Normal operation: IGBT ON and carrying current.
c2 : Short-circuit current detection (SC trigger).
c3 : Hard IGBT gate interrupt.
c4 : IGBT turns OFF.
c5 : Input “LOW”: IGBT OFF state.
c6 : Input “HIGH”: IGBT ON state, but during the active period of fault output, the IGBT doesn’t turn ON.
c7 : IGBT OFF state.
Figure 13. Short-Circuit Protection (Low-Side Operatio n Only)
Input/Output Interface Circuit
Figure 14. Recommended MCU I/O Interface Circuit
2nd Notes:
11. RC coupling at each input (parts shown dotted) might change depending on the PWM control scheme in the application and the wiring impedance of the application’s printed
circuit board. The input signal section of the Motion SPM® 45 product integrates a 5 k(typ.) pull-down resistor. Therefore, when using an external filtering resistor, pay atten-
tion to the signal voltage drop at input terminal.
Lower Arms
Control Input
Output Current
Sensing Voltage
of Shunt Resistance
Fault Output Signal
SC Reference Voltage
CR Circuit Time
Constant Delay
SC
Protection
Circuit State SET RESET
c6 c7
c3
c2
c1
c8
c4
c5
Internal IGBT
Gate - Emitter Voltage
MCU
COM
+5 V (for MCU or Control power)
,,
IN(UL) IN(VL) IN(WL)
,,
IN(UH) IN(VH) IN(WH)
VFO
RPF = 10 kSPM
FNA41560 / FNA41560B2 Motion SPM® 45 Series
©2011 Fairchild Semiconductor Corporation 13 www.fairchildsemi.com
FNA41560 / FNA41560B2 Rev. C3
Figure 15. Typical Application Circuit
3rd Notes:
1) To avoid malfunction, the wiring of each input should be as short as possible (less than 2 - 3 cm).
2) By virtue of integrat ing an application-specific type of HVIC insi de the M oti o n SPM® 45 pr od uct , dire ct coup l in g to MCU ter m i na ls w ithout any optocoupler or transformer isol a-
tion is possible.
3) VFO output is open-drain type . This signal line should be pulled up to the positive side of the MCU or control power supply with a resistor that makes IFO up to 1 mA (please
refer to Figure 14).
4) CSP15 of around seven times larger than bootstrap capacitor CBS is recommended.
5) Input signal is active-HIGH type. There is a 5 k resistor inside the IC to pull down each input signal line to GND. RC coupling circuits is recommanded for the prevention of
input signal oscillation. RSCPS time constant should be selected in the range 50 ~ 150 ns (recommended RS = 100 , CPS = 1 nF).
6) To prevent errors of the protection function, the wiring around RF and CSC should be as short as possible.
7) In the short-circuit protection circuit, please select the RFCSC time constant in the range 1.5 ~ 2 s.
8) The connection between con trol GND line and power GND line which includes the NU, NV, NW must be connected to only one point. Please do not connect the control GND
to the power GND by the broad pattern. Also, the wiring distance between control GND and power GND should be as short as possible.
9) Each capacitor should be mounted as close to the pins of the Motion SPM 45 product as possible.
10) To prevent surge destruction, the wiring between the smoothing capacitor and the P & GND pins should be as short as possible. The use of a high-f requen cy no n-ind ucti ve
capacitor of around 0.1 ~ 0.22 F between the P and GND pins is recommended.
11) Relays are used in almost every systems of electrical equipment in home appliances. In these cases, there should be sufficient distance between the MCU and the relays.
12) The zener diode or transient voltage suppressor should be adopted for the protection of ICs from the surge destruction between each pair of control supply terminals
(recommanded zener diode is 22 V / 1 W, which has the lower zener impedance characteristic than about 15 ).
13) Please choose the electrolytic capacitor with good temperature characteristic in CBS. Also, choose 0.1 ~ 0.2 F R-category ceramic capacitors with good temperature and
frequency characteristics in CBSC.
14) For the detailed information, please refer to the AN-9070, AN-9071, AN-9072, RD-344, and RD-345.
Fault
+15 V
CBS CBSC
CBS CBSC
CBS CBSC
CSP15 CSPC15
RPF
CBPF
RS
M
VDC
CDCS
Gating UH
Gating VH
Gating WH
Gating UL
Gating VL
Gating WL
CPF
M
C
U
RSW
RSV
RSU
U-Phase Current
V-Phase Current
W-Phase C urrent
RF
COM
VCC
IN(WL)
IN(VL)
IN(UL)
VFO
CSC
OUT(WL)
OUT(VL)
OUT(UL)
NW(9)
NV(8)
NU(7)
W (6)
V (5)
U (4)
P (3)
(25) VS(U)
(26) VB(U)
(23) VS(V)
(24) VB(V)
(10) CSC
(11) VFO
(14) IN(UL)
(13) IN(VL)
(12) IN(WL)
(20) IN(UH)
(19) IN(VH)
(21) VS(W)
(22) VB(W)
(17) VCC(H)
(18) IN(WH)
Input Signal for
Short-Circuit Protection
CSC
RS
RS
RS
RS
RS
RS
CPS
CPS
CPS
CPS
CPS CPS
IN(WH)
IN(VH)
IN(UH)
COM
VCC
VS(W)
VS(V)
VS(U)
VS(V)
VS(U)
VS(W)
VB(U)
VB(V)
VB(W)
(15) COM
OUT(WH)
OUT(VH)
OUT(UH)
LVIC
HVIC
(1) VTH
(2) RTH
RTH THERMISTOR
Temp. M onitoring
(16) VCC(L)
+5 V
CSPC05 CSP05
www.onsemi.com
1
ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent
coverage may be accessed at www.onsemi.com/site/pdf/PatentMarking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,
regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer
application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not
designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification
in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized
application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This
literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
N. American Technical Support: 8002829855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81358171050
www.onsemi.com
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 3036752175 or 8003443860 Toll Free USA/Canada
Fax: 3036752176 or 8003443867 Toll Free USA/Canada
Email: orderlit@onsemi.com
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
© Semiconductor Components Industries, LLC