志豐電子股份有限公司 KINGSTATE ELECTRONICS CORP 2/5 KPEG106-HS
A. SCOPE 範疇
This specification applies piezo audio transducer, KPEG106-HS
此規格書適用於壓電式蜂鳴器, KPEG106-HS
B. SPECIFICATION 規格
No. Item Unit Specification Condition
1 Operating V olt.
操作電壓 Vp-p MAX 30
2 Current consumption
消耗電流 mA MAX 18 at 10Vp-p,square wave,2.4KHz.
3 Sound pressure level
輸出音壓 dB MIN 88 at 10cm/10Vp-p,square wave,2.4KHz.
4 Electrostatic capacity
靜電容量 pF 90,000 ± 30% at 1KHz/1V
5 Operating temp.
操作溫度 ℃ -30 ~ +105 SPL Min80dB at “3” condition
音壓Min80dB，在第三項測試條件
6 S torage temp.
儲存溫度 ℃ -40 ~ +105
7 Dimension
尺寸 mm φ22.8 x H13.5 See appearance drawing
請參照外觀尺寸圖
8 Weight (MAX)
重量 gram 11.6
9 Material
材質 PC
（BLACK）
10 Terminal
端子 Pin type
(鍍全錫 PlatingSn) See appearance drawing
請參照外觀尺寸圖
11 Environmental
Protection Regulation
環保法規 RoHS
C. APPEARANCE DRA WING 外觀尺寸圖
移印周期字樣
12--- 2012
11--- 2011
年份
02
01
月份
(金色油墨)
Tol : ± 0.5
Unit : mm
志豐電子股份有限公司 KINGSTATE ELECTRONICS CORP 3/5 KPEG106-HS
D. TYPICAL FREQUENCY RESPONSE CUR VE 頻率響應曲線
E. MEASURING METHOD 測量方法
S.P.L. Measuring Circuit 音壓測試接線圖
Input Signal: 10Vp-p,2.4kHz, Square Wave
輸入信號: 10Vp-p,2.4kHz,方波
Mic : RION S.P.L meter UC30 or equivalent
Mic : RION 噪音計 UC30 或同等品
S.G : Hewlett Packard 33120A Function Generator or equivalent
S.G : Hewlett Packard 33120A 函數信號產生器或同等品
志豐電子股份有限公司 KINGSTATE ELECTRONICS CORP 4/5 KPEG106-HS
F. MECHANICAL CHARACTERISTICS 機械特性
No. Item Test Condition Evaluation st andard
1 Solderability
焊錫附著性
Lead terminals are immersed in rosin for 5 seconds and then immersed
in solder bath of +270±5℃ for 3±1 seconds.
端子部份浸入松香溶液 5秒後,再浸入+270±5℃溶融焊鍚槽中 3±1 秒.
90% min. lead terminals shall be
wet with solder . (Except the
edge of terminal)
浸入端子部份附著焊鍚 90%以
上.(末端斷面不算)
2 Soldering Heat
Resistance
焊錫耐熱性
Lead terminal are immersed up to 1.5mm from sounder’s body in soilder
bath of +300±5℃ for 3± 0.5 seconds or +260±5℃ for 10±1 seconds.
距離端子根部 1.5mm 的位置,浸入+300±5℃的焊鍚槽 3±0.5 秒,
或+260±5℃ 的焊錫槽 10±1 秒.
No interference in operation
操作上無任何不良
3 Terminal Mechanical
S trength
端子強度
The force 10 seconds of 9.8N (1.0kg) is applied to each terminal in axial
direction.
各端子的軸方向施以 9.8N (1.0kg)的力量 10 秒.
No damage and cutting off
端子不鬆動, 不脫落
4 Vibration
振動試驗
Buzzer shall be measured after being applied vibration of amplitude of
1.5mm with 10 to 55hz band of vibration frequency to each of 3
per-pendicular directions for 2 hours.
振動週波數 10～55HZ、全振幅 1.5mm 於 X.Y.Z 3 個方向,各2小時.
5 Drop test
落下測試
The part only shall be dropped from a height of 75cm onto a 40mm thick
wooden board 3 times in 3 axes (X.Y.Z). (a total of 9 times).
單體從 75 公分高處, X.Y.Z.3個方向,各3回,落於 40mm 厚木板上.
The value of oscillation
frequency/ current consumption
should be in 10% compared with
initial ones .The SPL should be
in ± 10dB compared with initial
one.
諧振頻率與消耗電流變化量須在
±10%內. 輸出音壓變化量須在
±10dB 內.
G. ENVIRONMENT TEST 環境測試
No. Item Test Condition Evaluation st andard
1 High temp. test
高溫測試 After being placed in a chamber at +105℃ for 240 hours
置於+105℃環境中 240 小時
2 Low temp. test
低溫測試 After being placed in a chamber at –40℃ for 240 hours
置於-40℃環境中 240 小時
3 Humidity test
相對濕度測試
After being placed in a chamber at +40℃ and 90±5% relative humidity
for 240 hours
置於+40℃, 相對濕度 90±5% 環境中 240 小時
4 Temp. cycle test
溫度循環試驗
The part shall be subjected to 5 cycles. One cycle shall be consist of::
單體承受溫度循環測試 5次,其循環內容如圖示:
+105℃
+25℃ +25℃
-40℃
0.5hr 0.5hr 0.25 0.5hr 0.5hr 0.5hr 0.25
3hours
Being placed for 4 hours at
+25℃, buzzer shall be
measured. The value of
oscillation frequency/ current
consumption should be in ±10%
compared with initial ones .The
SPL should be in ±10dB
compared with initial one.
經測試後, 靜置於+25℃（室溫）
環境中 4小時後,諧振頻率與消耗
電流變化量須在±10%內. 輸出音
壓變化量須在±10dB 內.
志豐電子股份有限公司 KINGSTATE ELECTRONICS CORP 5/5 KPEG106-HS
H. RELIABILITY TEST 信賴性測試
No. Item Test condition Evaluation st andard
1 Operating life
test
壽命測試
1.Continuous life test高溫壽命測試(連續)
48 hours continuous operation at +90℃ with rated voltage applied.
在+90℃環境下,以額定電壓連續操作 48 小時
2.Intermittent life test 室溫壽命測試(間歇)
A duty cycle of 1 minute on, 1 minutes off, a minimum of 5000 times at room
temp.( +25 ±2℃)and rated voltage applied
在室溫下(+25 ±2℃), 以額定電壓操作, 通電 1分鐘/斷電 1分鐘,測試
5000 次循環.
Being placed for 4 hours at
+25℃, buzzer shall be
measured. The value of
oscillation frequency/ current
consumption should be in ±10%
compared with initial ones .The
SPL should be in ±10dB
compared with initial one.
經測試後, 靜置於+25℃（室溫）
環境中 4小時後,諧振頻率與消耗
電流變化量須在±10%內. 輸出音
壓變化量須在±10dB 內.
TEST CONDITION.
S tandard Test Condition : a) Temperature : +5 ~ +35℃ b) Humidity : 45-85% c) Pressure : 860-1060mbar
一般測試條件 : a) 溫度 : +5 ~ +35℃ b) 濕度 : 45-85% c) 氣壓 : 860-1060mbar
Judgement Test Condition : a) Temperature : +25 ± 2℃ b) Humidity : 60-70% c) Pressure : 860-1060mbar
爭議時測試條件 : a) 溫度 : +25 ± 2℃ b) 濕度 : 60-70% c) 氣壓 : 860-1060mbar
I. PACKING ST ANDARD 包裝規格
