bq29440, bq2944L0 bq29441, bq29442, bq29443, bq29449, bq2944L9 www.ti.com SLUSA15C - JUNE 2010 - REVISED NOVEMBER 2010 Voltage Protection for 2-Series, 3-Series, or 4-Series Cell Li-Ion Batteries (Second-Level Protection) Check for Samples: bq29440, bq2944L0, bq29441, bq29442, bq29443, bq29449, bq2944L9 FEATURES APPLICATIONS * * 1 * * * * * 2-Series, 3-Series, or 4-Series Cell Secondary Protection External Capacitor-Controlled Delay Timer Low Power Consumption ICC < 2 A Typical [VCELL(ALL) < VPROTECT] High-Accuracy Overvoltage Protection: 25 mV with TA = 0C to 60C Fixed Overvoltage Protection Thresholds: 4.30 V, 4.35 V, 4.40 V, 4.45 V, 4.50 V Small 8L QFN Package Second-Level Protection in Li-Ion Battery Packs - Notebook Computers - Power Tools - Portable Equipment and Instrumentation DESCRIPTION The bq2944x is a secondary overvoltage protection IC for 2-series, 3-series, or 4-series cell Li-Ion battery packs that incorporates a high-accuracy precision overvoltage detection circuit. FUNCTION The voltage of each cell in a battery pack is compared to an internal reference voltage. If any cells reach an overvoltage condition, the bq2944x device starts a timer that provides a delay proportional to the capacitance on the CD pin. Upon expiration of the internal timer, the OUT pin changes from a low state to a high state. An optional latch configuration is available that holds the OUT pin in a high state indefinitely after an overvoltage condition has satisfied the specified delay timer period. The latch is released when the CD pin is shorted to GND. T T DRB Package (Top View) VC1 1 8 OUT VC2 2 7 VDD VC3 3 6 CD GND 4 5 VC4 P0012-02 1 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2010, Texas Instruments Incorporated bq29440, bq2944L0 bq29441, bq29442, bq29443, bq29449, bq2944L9 SLUSA15C - JUNE 2010 - REVISED NOVEMBER 2010 www.ti.com These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Table 1. ORDERING INFORMATION (1) PART NUMBER TA -40C to +110C (1) (2) (3) (4) OUT PIN LATCH OPTION PACKAGE PACKAGE DESIGNATOR ORDERING INFORMATION (2) PACKAGE MARKING OVP TAPE AND REEL (LARGE) (3) TAPE AND REEL (SMALL) (4) BQ29440 No 440 4.35 V BQ29440DRBR BQ29440DRBT BQ2944L0 Yes 44L0 4.35 V BQ2944L0DRBR BQ2944L0DRBT BQ29441 No 441 4.40 V BQ29441DRBR BQ29441DRBT BQ29442 No 442 4.45 V BQ29442DRBR BQ29442DRBT BQ29443 No 443 4.50 V BQ29443DRBR BQ29443DRBT QFN-8 DRB BQ29449 No 449 4.30 V BQ29449DRBR BQ29449DRBT BQ2944L9 Yes 44L9 4.30 V BQ2944L9DRBR BQ2944L9DRBT Example: bq2944L0DRBR is a device with the OUT latch option with a VOV threshold of 4.35 V. Contact Texas Instruments for other VOV threshold options. For the most current package and ordering information, see the Package Addendum at the end of this document, or the TI website at www.ti.com. Large tape and reel quantity is 3,000 units. Small tape and reel quantity is 250 units. THERMAL INFORMATION bq2944x THERMAL METRIC (1) DRB UNITS 8 PINS Junction-to-ambient thermal resistance (2) qJA 50.5 (3) qJC(top) Junction-to-case(top) thermal resistance qJB Junction-to-board thermal resistance (4) 19.3 yJT Junction-to-top characterization parameter (5) 0.7 yJB Junction-to-board characterization parameter (6) 18.9 qJC(bottom) Junction-to-case(bottom) thermal resistance (7) 5.2 (1) (2) (3) (4) (5) (6) (7) 25.1 C/W For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953. The junction-to-ambient thermal resistance under natural convection is obtained in a simulation on a JEDEC-standard, high-K board, as specified in JESD51-7, in an environment described in JESD51-2a. The junction-to-case (top) thermal resistance is obtained by simulating a cold plate test on the package top. No specific JEDECstandard test exists, but a close description can be found in the ANSI SEMI standard G30-88. The junction-to-board thermal resistance is obtained by simulating in an environment with a ring cold plate fixture to control the PCB temperature, as described in JESD51-8. The junction-to-top characterization parameter, yJT, estimates the junction temperature of a device in a real system and is extracted from the simulation data for obtaining qJA, using a procedure described in JESD51-2a (sections 6 and 7). The junction-to-board characterization parameter, yJB, estimates the junction temperature of a device in a real system and is extracted from the simulation data for obtaining qJA , using a procedure described in JESD51-2a (sections 6 and 7). The junction-to-case (bottom) thermal resistance is obtained by simulating a cold plate test on the exposed (power) pad. No specific JEDEC standard test exists, but a close description can be found in the ANSI SEMI standard G30-88. PIN FUNCTIONS 2 PIN NAME PIN NO. CD 6 Connection to external capacitor for programmable delay time DESCRIPTION GND 4 Ground pin OUT 8 Output VC1 1 Sense voltage input for top cell VC2 2 Sense voltage input for second-to-top cell VC3 3 Sense voltage input for third-to-top cell VC4 5 Sense voltage input for fourth-to-top cell (bottom cell) VDD 7 Power supply Submit Documentation Feedback Copyright (c) 2010, Texas Instruments Incorporated Product Folder Link(s): bq29440 bq2944L0 bq29441 bq29442 bq29443 bq29449 bq2944L9 bq29440, bq2944L0 bq29441, bq29442, bq29443, bq29449, bq2944L9 www.ti.com SLUSA15C - JUNE 2010 - REVISED NOVEMBER 2010 FUNCTIONAL BLOCK DIAGRAM RVD CVD VDD RIN VC1 ICD CIN RIN VC2 CIN RIN VC3 OUT CIN RIN VC4 VCD CIN GND CD CCD B0394-01 ABSOLUTE MAXIMUM RATINGS (1) over operating free-air temperature range (unless otherwise noted) VALUE/UNIT Supply voltage range, VMAX Input voltage range, VIN Output voltage range, VOUT VDD-GND -0.3 to 28 V VC1-GND, VC2-GND, VC3-GND -0.3 to 28 V VC1-VC2, VC2-VC3, VC3-VC4, VC4-GND -0.3 to 8 V CD-GND -0.3 to 8 V OUT-GND -0.3 to 28 V Storage temperature range, Tstg (1) -65C to 150C Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. RECOMMENDED OPERATING CONDITIONS MIN Supply voltage, VDD NOM 4 Input voltage range VC1-VC2, VC2-VC3, VC3-VC4, VC4-GND td(CD) delay-time capacitance CCD (See Figure 7.) Voltage monitor filter resistance RIN (See Figure 7.) Copyright (c) 2010, Texas Instruments Incorporated 0 0.1 MAX UNIT 25 V 5 V 0.1 F 1 k Submit Documentation Feedback Product Folder Link(s): bq29440 bq2944L0 bq29441 bq29442 bq29443 bq29449 bq2944L9 3 bq29440, bq2944L0 bq29441, bq29442, bq29443, bq29449, bq2944L9 SLUSA15C - JUNE 2010 - REVISED NOVEMBER 2010 www.ti.com RECOMMENDED OPERATING CONDITIONS (continued) MIN NOM Voltage monitor filter capacitance CIN (See Figure 7.) 0.01 0.1 Supply voltage filter resistance RVD (See Figure 7.) 0.1 Supply voltage filter capacitance CVD (See Figure 7.) Operating ambient temperature range, TA MAX UNIT 1 k F 0.1 -40 F 110 C ELECTRICAL CHARACTERISTICS Typical values stated where TA = 25C and VDD = 17 V, MIN/MAX values stated where TA = -40C to 110C and VDD = 4 V to 25 V (unless otherwise noted). PARAMETER VPROTECT TEST CONDITION MIN NOM bq29440 4.35 bq29441 Overvoltage detection bq29442 voltage bq29443 4.40 bq29449 4.30 MAX 4.45 UNIT V 4.50 VHYS Overvoltage detection hysteresis For non-latch devices only 200 VOA Overvoltage detection accuracy TA = 25C VOA_DRIFT Overvoltage threshold temperature drift XDELAY TA = 0C to 60C Overvoltage delay time Note: Does not include external capacitor variation scale factor TA = -40C to 110C Note: Does not include external capacitor variation 300 400 mV -10 10 mV TA = 0C to 60C -0.4 0.4 TA = -40C to 110C -0.6 0.6 6.0 9.0 12 5.5 9.0 13.5 mV/C s/F XDELAY_CTM Overvoltage delay time scale factor in See CUSTOMER TEST MODE. Customer Test Mode 0.08 s/F ICD(CHG) Overvoltage detection charging current See Figure 1. 140 nA ICD(DSG) Overvoltage detection discharging current See Figure 2. 60 A VCD Overvoltage detection external capacitor comparator threshold 1.2 V ICC Supply current VOUT OUT pin drive voltage (VC1-VC2), (VC2-VC3), (VC3-VC4) and (VC4-GND) = 3.5 V See Figure 3. 2 3.5 A 9.5 V (VC1-VC2), (VC2-VC3), (VC3-VC4) or (VC4-GND) = VPROTECT, VDD = 20 V, IOH = 0 to -10 A 6.5 8.0 (VC1-VC2), (VC2-VC3), (VC3-VC4) or (VC4-GND) = VPROTECT, VDD = 4.35 V, IOL = -10 A, TA = 0C to 60C 1.50 3.0 V (VC1-VC2), (VC2-VC3), (VC3-VC4) or (VC4-GND) = VPROTECT, VDD > 6 V, IOH = -10 A, TA = 0C to 60C 2.0 3.0 V (VC1-VC2), (VC2-VC3), (VC3-VC4) or (VC4-GND) = 4 V, IOL = 0 A IOUT(SHORT) OUT short circuit current OUT = 0 V, (VC1-VC2), (VC2-VC3), (VC3-VC4) or (VC4-GND) > VPROTECT, VDD = 18 V tr(OUT) (1) OUT output rise time CL = 1 nF, VDD = 4 V to 25 V, VOH(OUT) = 0 V to 5 V ZO(OUT) (1) OUT output impedance (1) 4 0.1 V 4 mA 5 s 2 k Specified by design. Not 100% tested in production. Submit Documentation Feedback Copyright (c) 2010, Texas Instruments Incorporated Product Folder Link(s): bq29440 bq2944L0 bq29441 bq29442 bq29443 bq29449 bq2944L9 bq29440, bq2944L0 bq29441, bq29442, bq29443, bq29449, bq2944L9 www.ti.com SLUSA15C - JUNE 2010 - REVISED NOVEMBER 2010 ELECTRICAL CHARACTERISTICS (continued) Typical values stated where TA = 25C and VDD = 17 V, MIN/MAX values stated where TA = -40C to 110C and VDD = 4 V to 25 V (unless otherwise noted). PARAMETER Input current at VCx pins IIN TEST CONDITION MIN Measured at VC1, (VC1-VC2), (VC2-VC3), (VC3-VC4) and (VC4-GND) = 3.5 V, TA = 0C to 60C See Figure 3. Measured at VC2, VC3 OR VC4, (VC1-VC2), (VC2-VC3), (VC3-VC4) and (VC4-GND) = 3.5 V, TA = 0C to 60C See Figure 3. NOM MAX UNIT -0.3 1.5 A -0.3 0.3 A TYPICAL CHARACTERISTICS ICD CHARGE CURRENT vs TEMPERATURE ICD DISCHARGE CURRENT vs TEMPERATURE -80 80 -90 75 -100 ICD Discharge Current (A) ICD Charge Current (nA) 70 -110 -120 -130 -140 -150 65 60 55 50 -160 45 -170 -180 -40 -20 0 20 40 60 Temperature (C) 80 40 -40 100 -20 0 20 40 60 Temperature (C) 80 100 G001 G002 Figure 1. ICD Charge Current Figure 2. ICD Discharge Current ICC IIN 1 VC1 OUT 8 IIN 2 VC2 VDD 7 IIN 3 VC3 CD 6 4 GND VC4 5 IIN Figure 3. ICC, IIN Measurement Copyright (c) 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): bq29440 bq2944L0 bq29441 bq29442 bq29443 bq29449 bq2944L9 5 bq29440, bq2944L0 bq29441, bq29442, bq29443, bq29449, bq2944L9 SLUSA15C - JUNE 2010 - REVISED NOVEMBER 2010 www.ti.com APPLICATIONS INFORMATION PROTECTION (OUT) TIMING AND DELAY TIME CAPACITOR SIZING The bq2944x uses an external capacitor to set delay timing during an overvoltage condition. When any of the cells exceed the overvoltage threshold, the bq2944x activates an internal current source of nominally 140 nA, which charges the external capacitor. When the external capacitor charges up to a voltage of nominally 1.2 V, the OUT pin transitions from a low state to a high state, by means of an internal pull-up network, to a regulated voltage of no more than 9.5 V when IOH = 0 mA. Cell Voltage VC1-VC2 VC2-VC3 VC3-VC4 VC4-GND VPROTECT VPROTECT - VHYS td L OUT H T0461-01 Figure 4. Timing for Overvoltage Sensing Sizing the external capacitor is based on the desired delay time as follows: CCD = td XDELAY Where td is the desired delay time and xDELAY is the overvoltage delay time scale factor, expressed in seconds per microFarad. xDELAY is nominally 9.0 s/F. For example, if a nominal delay of 3 seconds is desired, the customer should use a CCD capacitor that is 3 s/9.0 s/F = 0.33 F. The delay time is calculated as follows: t d = CCD XDELAY If the cell overvoltage condition is removed before the external capacitor reaches the reference voltage, the internal current source is disabled and an internal discharge block is employed to discharge the external capacitor down to 0 V. In this instance, the OUT pin remains in a low state. For latched versions of the bq2944x, if an overvoltage condition has caused the OUT pin to transition to a high state, the external capacitor remains charged even after the overvoltage condition has been removed. In this instance, the OUT pin remains in a high state. For non-latched versions, the OUT pin is allowed to transition back from a high to low state when the overvoltage condition is no longer present, and the external capacitor is discharged down to 0 V. 6 Submit Documentation Feedback Copyright (c) 2010, Texas Instruments Incorporated Product Folder Link(s): bq29440 bq2944L0 bq29441 bq29442 bq29443 bq29449 bq2944L9 bq29440, bq2944L0 bq29441, bq29442, bq29443, bq29449, bq2944L9 www.ti.com SLUSA15C - JUNE 2010 - REVISED NOVEMBER 2010 BATTERY CONNECTION FOR 2-SERIES, 3-SERIES, AND 4-SERIES CELL CONFIGURATIONS Figure 5, Figure 6, and Figure 7 show the 2-series, 3-series, and 4-series cell configurations. RVD 1 VC1 OUT 8 2 VC2 VDD 7 3 VC3 CD 6 4 GND VC4 5 CVD RIN CIN RIN CIN CCD Figure 5. 2-Series Cell Configuration RVD RIN 1 VC1 OUT 8 2 VC2 VDD 7 3 VC3 CD 6 4 GND VC4 5 CIN RIN CIN RIN CIN CVD CCD Figure 6. 3-Series Cell Configuration RVD RIN CIN RIN CIN RIN CIN RIN CIN 1 VC1 OUT 8 2 VC2 VDD 7 3 VC3 CD 6 4 GND VC4 5 CVD CCD Figure 7. 4-Series Cell Configuration Copyright (c) 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): bq29440 bq2944L0 bq29441 bq29442 bq29443 bq29449 bq2944L9 7 bq29440, bq2944L0 bq29441, bq29442, bq29443, bq29449, bq2944L9 SLUSA15C - JUNE 2010 - REVISED NOVEMBER 2010 www.ti.com CELL CONNECTION SEQUENCE NOTE Before connecting the cells, propagate the overvoltage delay timing capacitor, CCD. The recommended cell connection sequence begins from the bottom of the stack, as follows: 1. GND 2. VC4 3. VC3 4. VC2 5. VC1 While not advised, connecting the cells in a sequence other than that described above does not result in errant activity on the OUT pin. For example: 1. GND 2. VC4, VC3, VC2, or VC1 3. Remaining VCx pin 4. Remaining VCx pin 5. Remaining VCx pin CUSTOMER TEST MODE Customer Test Mode (CTM) helps to greatly reduce the overvoltage detection delay time and enable quicker customer production testing. This mode is intended for quick-pass board-level verification tests, and, as such, individual cell overvoltage levels may deviate slightly from the specifications (VPROTECT, VOA). If accurate overvoltage thresholds are to be tested, use the standard delay settings that are intended for normal use. To enter CTM, VDD should be set to approximately 9.5 V higher than VC1. When CTM is entered, the device switches from the normal overvoltage delay time scale factor, xDELAY, to a significantly reduced factor, xDELAY_CTM, thereby reducing the delay time during an overvoltage condition. The CTM overvoltage delay time is similar to the equation presented in PROTECTION (OUT) TIMING AND DELAY TIME CAPACITOR SIZING with the substitution of xDELAY_CTM in place of xDELAY: t d _ CTM = CCD XDELAY_CTM CAUTION Avoid exceeding any Absolute Maximum Voltages on any pins when placing the part into Customer Test Mode. Also, avoid exceeding Absolute Maximum Voltages for the individual cell voltages (VC1-VC2), (VC2-VC3), (VC3-VC4), and (VC4-GND). Stressing the pins beyond the rated limits may cause permanent damage to the device. To exit CTM, power off the device and then power it back on. For latched versions of the bq2944x, the external CCD capacitor must be externally discharged if any overvoltage functionality is exercised during protection testing. This can be accomplished by shorting the CD pin to GND. If the CCD capacitor is not explicitly discharged, a residual charge may cause the overvoltage delay time to be inaccurate. 8 Submit Documentation Feedback Copyright (c) 2010, Texas Instruments Incorporated Product Folder Link(s): bq29440 bq2944L0 bq29441 bq29442 bq29443 bq29449 bq2944L9 bq29440, bq2944L0 bq29441, bq29442, bq29443, bq29449, bq2944L9 www.ti.com SLUSA15C - JUNE 2010 - REVISED NOVEMBER 2010 REVISION HISTORY Changes from Revision B (June 2010) to Revision C Page * Added new protection thresholds ......................................................................................................................................... 1 * Changed occurrences of VDD to VDD throughout document ................................................................................................ 1 * Added part numbers ............................................................................................................................................................. 2 * Changed the Functional Block Diagram ............................................................................................................................... 3 * Changed the Electrical Characteristics ................................................................................................................................. 4 * Deleted 3.5 from one of the maximum values from the VOUT specification .......................................................................... 4 * Changed nominal delay time ................................................................................................................................................ 6 Copyright (c) 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): bq29440 bq2944L0 bq29441 bq29442 bq29443 bq29449 bq2944L9 9 PACKAGE OPTION ADDENDUM www.ti.com 1-Jun-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) BQ29440DRBR ACTIVE SON DRB 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR BQ29440DRBT ACTIVE SON DRB 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR BQ29441DRBR ACTIVE SON DRB 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR BQ29441DRBT ACTIVE SON DRB 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR BQ29442DRBR ACTIVE SON DRB 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR BQ29442DRBT ACTIVE SON DRB 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR BQ29443DRBR ACTIVE SON DRB 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR BQ29443DRBT ACTIVE SON DRB 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR BQ29449DRBR ACTIVE SON DRB 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR BQ29449DRBT ACTIVE SON DRB 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Samples (Requires Login) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 1-Jun-2012 Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 25-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing BQ29440DRBR SON DRB 8 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 3000 330.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2 BQ29440DRBT SON DRB 8 250 180.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2 BQ29441DRBR SON DRB 8 3000 330.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2 BQ29441DRBT SON DRB 8 250 180.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2 BQ29442DRBR SON DRB 8 3000 330.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2 BQ29442DRBT SON DRB 8 250 180.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2 BQ29443DRBR SON DRB 8 3000 330.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2 BQ29443DRBT SON DRB 8 250 180.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2 BQ29449DRBR SON DRB 8 3000 330.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2 BQ29449DRBT SON DRB 8 250 180.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 25-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) BQ29440DRBR SON DRB 8 3000 367.0 367.0 35.0 BQ29440DRBT SON DRB 8 250 210.0 185.0 35.0 BQ29441DRBR SON DRB 8 3000 367.0 367.0 35.0 BQ29441DRBT SON DRB 8 250 210.0 185.0 35.0 BQ29442DRBR SON DRB 8 3000 367.0 367.0 35.0 BQ29442DRBT SON DRB 8 250 210.0 185.0 35.0 BQ29443DRBR SON DRB 8 3000 367.0 367.0 35.0 BQ29443DRBT SON DRB 8 250 210.0 185.0 35.0 BQ29449DRBR SON DRB 8 3000 367.0 367.0 35.0 BQ29449DRBT SON DRB 8 250 210.0 185.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated