19-3959; Rev 2; 5/06 Quad SPST CMOS Analog Switches Features The DG201A and DG211 are normally closed, quad single-pole single-throw (SPST) analog switches. These CMOS switches can be continuously operated with power supplies ranging from 4.5V to 18V. Maxim guarantees that these switches will not latch up if the power supplies are disconnected with input signals still connected. Guaranteed 4.5V to 18V Operation Both devices have guaranteed break-before-make switching. The DG201A differs from the DG211 primarily in switching speeds. The DG201A has a maximum turn-off time of 450ns and a maximum turn-on time of 600ns. The DG211 has a maximum turn-off time of 500ns and a maximum turn-on time of 1000ns. Monolithic, Low-Power CMOS Design Compared to the original manufacturer's products, Maxim's DG201A and DG211 consume significantly lower power making them better suited for portable applications. Maxim has also eliminated the need for the third (VL) power supply that is required for the operation of the original manufacturer's DG211. No VL Supply Required Nonlatching with Supplies Turned Off and Input Signals Present CMOS and TTL Logic Compatible Ordering Information PART TEMP RANGE DG201ACUE 0C to +70C 16 TSSOP PIN-PACKAGE DG201ACSE 0C to +70C 16 SO DG201ACJ 0C to +70C 16 Plastic DIP DG201C/D 0C to +70C Dice -40C to +85C 16 QFN (5 5) DG201AEUE -40C to +85C 16 TSSOP DG201ADY -40C to +85C 16 SO DG201ADJ -40C to +85C 16 Plastic DIP DG201AAK -55C to +125C 16 CERDIP Test Equipment DG201ABK DG211CUE -25C to +85C 0C to +70C 16 CERDIP 16 TSSOP Communications Systems DG211CSE 0C to +70C 16 SO PBX, PABX DG211CJ 0C to +70C 16 Plastic DIP Guidance and Control Systems DG211C/D 0C to +70C Dice Head Up Displays DG211EGE -40C to +85C Military Radios DG211EUE DG211DY -40C to +85C -40C to +85C DG211DJ -40C to +85C Applications Winchester Disk Drives Pin Configurations continued at end of data sheet. DG201AEGE 16 QFN (5 5) 16 TSSOP 16 SO 16 Plastic DIP Pin Configurations Typical Operating Circuit IN1 1 16 IN2 D1 2 15 D2 S1 3 14 S2 V- 4 GND 5 12 S4 6 6 11 D4 7 7 10 IN4 8 5k 5k VIN x 10V * 1 16 * 2 5 40k 15 14 3 -15V 4 10k TOP VIEW DG201A DG211 * 8 13 +15V 9 * 20k VOUT 13 V+ DG201A DG211 12 N.C. 11 S3 10 D3 9 IN3 DIP/SO/TSSOP PROGRAMMABLE GAIN AMPLIFIER NOTE: *PINS 1, 8, 9, AND 16 ARE LOGIC CONTROL INPUTS LOGIC SWITCH 0 1 ON OFF ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim's website at www.maxim-ic.com. 1 DG201A/DG211 General Description DG201A/DG211 Quad SPST CMOS Analog Switches ABSOLUTE MAXIMUM RATINGS (DG211) V+ to V-.......................................................................44V VIN to Ground.................................................... .........V-, V+ VL to Ground.........................................................-0.3V, 25V VS or VD to V+............................................................0, -40V VS or VD to V-..............................................................0, 40V V+ to Ground....................................................................25V V- to Ground.................................................................-25V Current, Any Terminal Except S or D...............................30mA Continuous Current, S or D............................................20mA Peak Current, S or D (pulsed at 1ms 10% duty cycle max).............................70mA Storage Temperature Range.........................-65C to +125C Operating Temperature Range DG211C ...........................................................0C to +70C DG211D/E ....................................................-40C to +85C Power Dissipation (TA = +70C) (Note 1) 16-Pin Plastic Dip (derate 10.5mW/C above +70C) ..842mW 16-Pin Narrow SO (derate 8.3mW/C above+70C). ....696mW 16-Pin TSSOP (derate 9.4mW/C above +70C) ..........755mW 16-Pin QFN (5 5) (derate 19.2mW/C above +70C) .........................1538mW Note 1: Device mounted with all leads soldered to PC board. Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (DG211) (V+ = +15V, V- = -15V, GND = 0, TA = +25C, unless otherwise noted.) (For more information on TYP values see Note 2.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS 15 V 115 175 0.01 5.0 SWITCH Analog Signal Range VANALOG Drain-Source ON-Resistance RDS (ON) -15 Source OFF-Leakage Current IS (OFF) VIN = 2.4V Drain OFF-Leakage Current ID (OFF) VIN = 2.4V Drain ON-Leakage Current (Note 3) ID (ON) VIN = 0.8V VD = 10V, VIN = 0.8V, IS = 1mA VS = 14V, VD = -14V VS = -14V, VD = 14V -5.0 VS = 14V, VD = -14V VS = -14V, VD = 14V 0.01 -5.0 -0.02 -5.0 -0.15 -1.0 -0.0004 VS = VD = -14V VS = VD = -14V -0.02 0.1 5.0 nA 5.0 INPUT VIN = 2.4V Input Current with Input Voltage High IINH Input Current with Input Voltage Low IINL VIN = 0 tON See Switching Time Test Circuit VS = 2V, RL = 1k, CL = 35pF VIN = 15V 0.003 -1.0 1.0 A -0.0004 DYNAMIC Turn-ON Time Turn-OFF Time tOFF1 tOFF2 460 1000 360 500 Source OFF-Capacitance CS (OFF) VS = 0, VIN = 5V, f = 1MHz 5 Drain OFF-Capacitance CD (OFF) VD = 0, VIN = 5V, f = 1MHz 5 VD = VS = 0, VIN = 0, f = 1MHz 16 Channel ON-Capacitance OFF-Isolation (Note 4) Crosstalk (Channel to Channel) 2 CD + S (ON) OIRR CCRR ns 450 pF 70 VIN = 5V, RL = 1k, CL = 15pF, VS = 1VRMS, f = 100kHz 90 _______________________________________________________________________________________ dB Quad SPST CMOS Analog Switches (V+ = +15V, V- = -15V, GND = 0, TA = +25C, unless otherwise noted.) (For more information on TYP values see Note 2.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX 0.02 0.4 0.01 0.4 0 0 UNITS SUPPLY Positive Supply Current I+ - Negative Supply Current I Logic Supply Current IL Power-Supply Range for Continous Operation VIN = 0 and 2.4V (all) 4.5 VOP mA 18 V Note 2: Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing. Note 3: ID(ON) is leakage from driver into "ON" switch. Note 4: OFF-Isolation = 20 log VS/VD, VS = input to OFF switch, VD = output. ABSOLUTE MAXIMUM RATINGS (DG201A) Voltages Reference to VV+.........................................................................44V GND......................................................................25V Digital Inputs (Note 1), VS, VD ............................-2V to (V+ + 2V) or 20mA, whichever occurs first Current, Any Terminal Except S or D..............................30mA Continuous Current, S or D..........................................20mA Peak Current, S or D (pulsed at 1ms 10% duty cycle max).........................70mA Operating Temperature Range DG201AA ..................................................-55C to +125C DG201AD/E ...............................................-40C to +85C DG201AC ........................................................0C to +70C Storage Temperature Range.........................-65C to +150C Power Dissipation (Note 2) 16-Pin Plastic Dip (derate 10.5mW/C above +70C) ...842mW 16-Pin SO (derate 8.7mW/C above +70C) .................696mW 16-Pin TSSOP (derate 9.4mW/C above +70C) ...........755mW 16-Pin QFN (5 5) (derate 19.2mW/C above +70C)...........................1538mW 16-Pin CERDIP (derate 10.0mW/C above +70C)......800mW Note 1: Signals on S_, D_, or IN_ exceeding V+ or V- on Maxim's DG201A will be clamped by internal diodes, and are also internally current limited to 25mA. Note 2: Device mounted with all leads soldered to PC board. Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (DG201A) (V+ = +15V, V- = -15V, GND = 0, TA = +25C, unless otherwise noted.) (For more information on TYP values see Note 3.) PARAMETER SYMBOL CONDITIONS DG201AA MIN TYP DG201AC, D, E MAX MIN 15 -15 TYP MAX UNITS SWITCH Analog Signal Range VANALOG Drain-Source ON Resistance RDS (ON) -15 VD = 10V, VIN = 0.8V, IS = 1mA Source OFF-Leakage Current IS (OFF) VIN = 2.4V Drain OFF-Leakage Current ID (OFF) VIN = 2.4V Drain ON-Leakage Current (Note 4) ID (ON) VIN = 0.8V VS = 14V, VD = -14V VS = -14V, VD = 14V VS = -14V, VD = 14V VS = 14V 175 115 200 1.0 0.01 5.0 -1.0 -0.02 0.01 0.1 -1.0 115 -0.02 VS = -14V V 0.01 -1.0 VS = 14V, VD = -14V 15 -5.0 -0.02 -5.0 -0.02 1.0 0.01 1.0 0.1 5.0 nA 1.0 -1.0 _______________________________________________________________________________________ 3 DG201A/DG211 ELECTRICAL CHARACTERISTICS (DG211) (continued) DG201A/DG211 Quad SPST CMOS Analog Switches ELECTRICAL CHARACTERISTICS (DG201A) (continued) (V+ = +15V, V- = -15V, GND = 0, TA = +25C, unless otherwise noted.) (For more information on TYP values see Note 3.) PARAMETER SYMBOL CONDITIONS DG201AA MIN TYP DG201AC, D, E MAX MIN TYP MAX UNITS INPUT Input Current with Input Voltage High IINH Input Current with Input Voltage Low IINL VIN = 2.4V -1.0 -1.0 VIN = 15V 1.0 VIN = 0+ -1.0 1.0 A -1.0 DYNAMIC Turn-ON Time tON Turn-OFF Time tOFF1 Charge Injection Q See Figure 1 Switching Time Test Circuit CL = 1000pF, VGEN = 0, RGEN = 0 Source OFF-Capacitance CS (OFF) Drain OFF-Capacitance CD (OFF) Channel ON-Capacitance CD (ON) VD = VS = 0, + CS (ON) VIN = 0 480 600 480 600 370 450 370 450 20 VS = 0, VIN = 5V 20 5 5 5 5 ns pC f = 140kHz pF 16 16 OFF-Isolation VIN = 5V, ZL = 75 70 70 Crosstalk (Channel to Channel) VS = 2.0V, f = 100kHz 90 90 dB SUPPLY Positive Supply Current Negative Supply Current Power-Supply Range for Continuous Operation I+ IVOP All channels ON or OFF All channels ON or OFF 0.02 -0.1 4.5 0.1 -0.01 0.02 -0.1 18 4.5 Note 3: Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing. Note 4: ID (ON) is leakage from driver into "ON" switch. 4 _______________________________________________________________________________________ 0.1 mA 18 V -0.01 Quad SPST CMOS Analog Switches (V+ = +15V, V- = -15V, GND = 0, TA = full opearting temperature range, unless otherwise noted.) (For more information on TYP values see Note 3.) PARAMETER SYMBOL CONDITIONS DG201AA MIN TYP DG201AC, D, E MAX MIN 15 -15 TYP MAX UNITS SWITCH Analog Signal Range VANALOG Drain-Source ON Resistance (Note 5) RDS (ON) -15 VD = 10V, VIN = 0.8V, IS = 1mA Source OFF Leakage Current IS (OFF) VIN = 2.4V Drain OFF Leakage Current ID (OFF) VIN = 2.4V Drain ON Leakage Current (Note 6) ID (ON) VIN = 0.8V 250 VS = 14V, VD = -14V VS = -14V, VD = 14V 100 -100 VS = 14V, VD = -14V VS = -14V, VD = 14V VD = 14V V 250 100 -100 100 -100 VS = -14V 15 100 -100 200 nA 200 -200 -200 -1.0 -1.0 INPUT Input Current with Input Voltage High IINH Input Current with Input Voltage Low IINL VIN = 2.4V VIN = 15V VIN = 0 1.0 -1.0 1.0 A -1.0 Note 5: Electrical characteristics, such as ON-Resistance, will change when power supplies other than 15V, are used. Note 6: ID (ON) is leakage from driver into "ON" switch. Pin Description PIN NAME FUNCTION DIP/SO/TSSOP QFN 1, 16, 9, 8 15, 14, 7, 6 IN1-IN4 2, 15, 10, 7 16, 13, 8, 5 D1-D4 Analog Switch Drain Terminal 3, 14, 11, 6 1, 12, 9, 4 S1-S4 Analog Switch Source Terminal 4 2 V- Negative-Supply Voltage Input Input 5 3 GND Ground 12 10 N.C. No Connection 13 11 V+ Positive-Supply Voltage Input--Connected to Substrate Switching Time Test Circuit Switch output waveform shown for VS = constant with logic input waveform as shown. Note that VS may be +ve or -ve as per switching times test circuit. VO is the steady state output with switch on. Feedthrough via gate capacitance may result in spikes at leading and trailing edge of output waveform. _______________________________________________________________________________________ 5 DG201A/DG211 ELECTRICAL CHARACTERISTICS (DG201A) DG201A/DG211 Quad SPST CMOS Analog Switches LOGIC INPUT LOGIC "0" - SW ON 3V tf < 20ns tr < 20ns 50% SWITCH INPUT 0 VS = +2V SWITCH INPUT VS SWITCH OUTPUT 0 V0 V0 0.9 0.9 V0 tON CL 35pF RL 1k (REPEAT TEST FOR IN2, IN3, AND IN4) toff1 GND V-15V 0 toff2 SWITCH OUTPUT V0 D1 S1 LOGIC IN1 INPUT 0.1 RL V0 = VS R + R L DS(ON) +15V V+ Figure 1. Switching Time Typical RDS(ON) vs. Power Supplies for Maxim's DG201A, and DG211 RDS(ON) AT ANALOG SIGNAL LEVEL POWER SUPPLIES -5V +5V -10V +10V -15V 5V 350 380 -- -- -- -- 10V -- -- 165 250 -- -- 15V -- -- 125 160 135 155 Protecting Against Fault Conditions Fault conditions occur when power supplies are turned off when input signals are still present, or when overvoltages occur at the inputs during normal operation. In either case, source-to-body diodes can be forward biased and conduct current from the signal source. If this current is required to be kept to low (A) levels then the addition of external protection diodes is recommended. Pin Configurations (continued) To provide protection for overvoltages up to 20V above the supplies, a 1N4001 or 1N914 type diode should be placed in series with the positive and negative supplies as shown in Figure 2. The addition of these diodes will reduce the analog signal range to 1V below the positive supply and 1V above the negative supply. IN4001 -15V 1 16 2 15 S1 1 V- 2 GND S4 14 3 4 5 TOP VIEW DG201A DG211 13 12 D1 IN1 IN2 D2 6 11 16 15 14 13 7 10 8 9 12 S2 11 V+ 3 10 N.C. 4 9 S3 DG201A DG211 5 6 7 8 D4 IN4 IN3 D3 Figure 2. Protection against Fault Conditions QFN* 6 +15V _______________________________________________________________________________________ IN4001 +15V Quad SPST CMOS Analog Switches N E H INCHES MILLIMETERS MAX MIN 0.069 0.053 0.010 0.004 0.014 0.019 0.007 0.010 0.050 BSC 0.150 0.157 0.228 0.244 0.016 0.050 MAX MIN 1.35 1.75 0.10 0.25 0.35 0.49 0.19 0.25 1.27 BSC 3.80 4.00 5.80 6.20 0.40 SOICN .EPS DIM A A1 B C e E H L 1.27 VARIATIONS: 1 INCHES TOP VIEW DIM D D D MIN 0.189 0.337 0.386 MAX 0.197 0.344 0.394 MILLIMETERS MIN 4.80 8.55 9.80 MAX 5.00 8.75 10.00 N MS012 8 AA 14 AB 16 AC D A B e C 0-8 A1 L FRONT VIEW SIDE VIEW PROPRIETARY INFORMATION TITLE: PACKAGE OUTLINE, .150" SOIC APPROVAL DOCUMENT CONTROL NO. 21-0041 REV. B 1 1 _______________________________________________________________________________________ 7 DG201A/DG211 Package Information (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.) Package Information (continued) (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.) PDIPN.EPS DG201A/DG211 Quad SPST CMOS Analog Switches 8 _______________________________________________________________________________________ Quad SPST CMOS Analog Switches CDIPS.EPS _______________________________________________________________________________________ 9 DG201A/DG211 Package Information (continued) (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.) Package Information (continued) (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.) TSSOP4.40mm.EPS DG201A/DG211 Quad SPST CMOS Analog Switches PACKAGE OUTLINE, TSSOP 4.40mm BODY 21-0066 10 ______________________________________________________________________________________ G 1 1 Quad SPST CMOS Analog Switches 32L QFN.EPS ______________________________________________________________________________________ 11 DG201A/DG211 Package Information (continued) (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.) DG201A/DG211 Quad SPST CMOS Analog Switches Package Information (continued) (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.) Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 12 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 (c) 2006 Maxim Integrated Products is a registered trademark of Maxim Integrated Products, Inc.