OPA333A-EP,, OPA2333A-EP www.ti.com ............................................................................................................................................................ SGLS383B - APRIL 2007 - REVISED JUNE 2008 1.8-V MICROPOWER CMOS OPERATIONAL AMPLIFIERS ZERO-DRIFT SERIES FEATURES 1 * * * * * * * Low Offset Voltage: 23 V (Max) 0.01-Hz to 10-Hz Noise: 1.1 VPP Quiescent Current: 17 A Single-Supply Operation Supply Voltage: 1.8 V to 5.5 V Rail-to-Rail Input/Output MicroSize Packages: SC70 and SOT23 SUPPORTS DEFENSE, AEROSPACE, AND MEDICAL APPLICATIONS * * * * * * * APPLICATIONS * * * * * * Transducer Applications Temperature Measurements Electronic Scales Medical Instrumentation Battery-Powered Instruments Handheld Test Equipment (1) D PACKAGE (TOP VIEW) OUT A -IN A +IN A V- 1 2 3 4 8 7 6 5 Controlled Baseline One Assembly/Test Site One Fabrication Site Available in Military (-55C/125C) Temperature Range (1) Extended Product Life Cycle Extended Product-Change Notification Product Traceability Custom temperature ranges available DBV PACKAGE (TOP VIEW) V+ OUT B -IN B +IN B OUT V- +IN 1 2 3 5 V+ 4 -IN DCK PACKAGE (TOP VIEW) +IN V- -IN 1 2 3 5 V+ 4 OUT 500nV/div 0.1Hz TO 10Hz NOISE 1s/div 1 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2007-2008, Texas Instruments Incorporated OPA333A-EP,, OPA2333A-EP SGLS383B - APRIL 2007 - REVISED JUNE 2008 ............................................................................................................................................................ www.ti.com DESCRIPTION/ORDERING INFORMATION The OPA333A series of CMOS operational amplifiers uses a proprietary auto-calibration technique to simultaneously provide very low offset voltage (10 V max) and near-zero drift over time and temperature. These miniature, high-precision, low-quiescent-current amplifiers offer high-impedance inputs that have a common-mode range 100 mV beyond the rails, and rail-to-rail output that swings within 50 mV of the rails. Single or dual supplies as low as 1.8 V (0.9 V) and up to 5.5 V (2.75 V) may be used. They are optimized for low-voltage single-supply operation. The OPA333A family offers excellent common-mode rejection ratio (CMRR) without the crossover associated with traditional complementary input stages. This design results in superior performance for driving analog-to-digital converters (ADCs) without degradation of differential linearity. The OPA333A (single version) is available in the SC70-5 and SOT23-5 packages. The OPA2333A (dual version) is offered in the SO-8 package. All versions are specified for operation from -55C to 125C. ORDERING INFORMATION (1) (1) (2) PRODUCT PACKAGE-LEAD PACKAGE DESIGNATOR PACKAGE MARKING (2) OPA333AMDBVREP SOT23-5 DBV OBYM OPA333AMDCKREP SC70-5 DCK CHQ OPA2333AMDREP SO-8 D 2333EP For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI Web site at www.ti.com. Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. PIN CONFIGURATIONS OPA333A OUT 1 V- 2 +IN 5 3 OPA2333A OPA333A 4 V+ -IN SOT23-5 +IN 1 V- 2 -IN 5 OUT A V+ -IN A 3 4 OUT 1 8 V+ 7 OUT B 6 -IN B 5 +IN B A 2 +IN A 3 V- 4 B SC70-5 SO-8 Absolute Maximum Ratings (1) over operating free-air temperature range (unless otherwise noted) MIN Supply voltage Signal input terminals, voltage (2) Output short circuit -0.3 (3) MAX UNIT 7 V (V+) + 0.3 V Continuous Operating temperature range -55 125 C Storage temperature range -65 150 (4) C 150 C Junction temperature ESD rating (1) (2) (3) (4) 2 Human-Body Model (HBM) 4000 Charged-Device Model (CDM) 1000 V Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. Input terminals are diode clamped to the power-supply rails. Input signals that can swing more than 0.3 V beyond the supply rails should be current limited to 10 mA or less. Short circuit to ground, one amplifier per package Long-term high-temperature storage and/or extended use at maximum recommended operating conditions may result in a reduction of overall device life. See http://www.ti.com/ep_quality for additional information on enhanced plastic packaging. Submit Documentation Feedback Copyright (c) 2007-2008, Texas Instruments Incorporated Product Folder Link(s): OPA333A-EP OPA2333A-EP OPA333A-EP,, OPA2333A-EP www.ti.com ............................................................................................................................................................ SGLS383B - APRIL 2007 - REVISED JUNE 2008 Electrical Characteristics: VS = 1.8 V to 5.5 V Boldface limits apply over the specified temperature range, TA = -55C to 125C. At TA = 25C, RL = 10 k connected to VS/2, VCM = VS/2, and VOUT = VS/2 (unless otherwise noted). PARAMETER TEST CONDITIONS MIN TYP MAX UNIT 2 10 V 22 V OFFSET VOLTAGE Input offset voltage VOS VS = 5 V over temperature vs temperature vs power supply dVOS/dT PSRR V/C 0.02 VS = 1.8 V to 5.5 V 1 Long-term stability (1) 6 V/V (1) Channel separation, dc V/V 0.1 INPUT BIAS CURRENT Input bias current IB 70 over Temperature Input offset current 200 150 IOS 140 pA pA 400 pA NOISE Input voltage noise, f = 0.01 Hz to 1 Hz 0.3 VPP Input voltage noise, f = 0.1 Hz to 10 Hz 1.1 VPP 100 fA/Hz Input current noise, f = 10 Hz in INPUT VOLTAGE RANGE Common mode voltage range Common-Mode Rejection Ratio VCM CMRR (V-) - 0.1 (V-) - 0.1 V < VCM < (V+) + 0.1 V 102 (V+) + 0.1 V 130 dB Differential 2 pF Common mode 4 pF 130 dB INPUT CAPACITANCE OPEN-LOOP GAIN Open-loop voltage gain AOL (V-) + 100 mV < VO < (V+) - 100 mV, RL = 10 k 104 FREQUENCY RESPONSE Gain-bandwidth product Slew rate GBW SR CL = 100 pF 350 kHz G=1 0.16 V/s OUTPUT Voltage output swing from rail RL = 10 k over temperature 30 RL = 10 k Short-circuit current ISC Capacitive load drive CL (2) Open-loop output impedance f = 350 kHz, IO = 0 50 mV 85 mV 5 mA 2 k POWER SUPPLY Specified voltage range Quiescent current per amplifier VS IQ 1.8 IO = 0 17 VS = 5 V 100 over temperature Turn-on time 5.5 V 25 A 30 A s TEMPERATURE RANGE Specified range (1) (2) -55 125 C 300-hour life test at 150C demonstrated randomly distributed variation of approximately 1 V See Typical Characteristics Copyright (c) 2007-2008, Texas Instruments Incorporated Product Folder Link(s): OPA333A-EP OPA2333A-EP Submit Documentation Feedback 3 OPA333A-EP,, OPA2333A-EP SGLS383B - APRIL 2007 - REVISED JUNE 2008 ............................................................................................................................................................ www.ti.com Electrical Characteristics: VS = 1.8 V to 5.5 V (continued) Boldface limits apply over the specified temperature range, TA = -55C to 125C. At TA = 25C, RL = 10 k connected to VS/2, VCM = VS/2, and VOUT = VS/2 (unless otherwise noted). MAX UNIT Operating range PARAMETER TEST CONDITIONS MIN -55 TYP 125 C Storage range -65 150 C JA Thermal resistance SOT23-5 200 C/W SO-8 150 C/W SC70-5 250 C/W TYPICAL CHARACTERISTICS At TA = 25C, VS = 5 V, and CL = 0 pF (unless otherwise noted). OFFSET VOLTAGE DRIFT PRODUCTION DISTRIBUTION 0 0.0025 0.0050 0.0075 0.0100 0.0125 0.0150 0.0175 0.0200 0.0225 0.0250 0.0275 0.0300 0.0325 0.0350 0.0375 0.0400 0.0425 0.0450 0.0475 0.0500 -10 -9 -8 -7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 8 9 10 Population Population OFFSET VOLTAGE PRODUCTION DISTRIBUTION Offset Voltage (V) Offset Voltage Drift (V/_ C) COMMON-MODE REJECTION RATIO vs FREQUENCY 140 100 200 120 80 150 100 60 100 40 50 20 0 40 -50 20 -100 0 0 -20 10 100 1k 10k 100k 1M CMRR (dB) 250 Phase (_ ) AOL (dB) OPEN-LOOP GAIN vs FREQUENCY 120 80 60 1 10 Frequency (Hz) 4 Submit Documentation Feedback 100 1k 10k 100k 1M Frequency (Hz) Copyright (c) 2007-2008, Texas Instruments Incorporated Product Folder Link(s): OPA333A-EP OPA2333A-EP OPA333A-EP,, OPA2333A-EP www.ti.com ............................................................................................................................................................ SGLS383B - APRIL 2007 - REVISED JUNE 2008 TYPICAL CHARACTERISTICS (continued) POWER-SUPPLY REJECTION RANGE vs FREQUENCY OUTPUT VOLTAGE SWING vs OUTPUT CURRENT 120 3 VS = 2.75V VS = 0.9V +PSRR 100 2 Output Swing (V) PSRR (dB) -PSRR 80 60 40 -40_C 1 +25_C -40_ C -1 +125_C +25_C -2 20 -40_ C -3 0 1 10 100 1k 10k 100k 1M 0 1 2 3 Frequency (Hz) INPUT BIAS CURRENT vs COMMON-MODE VOLTAGE 6 7 8 9 10 INPUT BIAS CURRENT vs TEMPERATURE 150 -IB 60 VS = 5V -IB 50 IB (pA) 20 0 -20 0 +IB -50 -40 VS = 5.5V VS = 1.8V -IB 100 40 IB (pA) 5 200 80 -100 -60 +IB -80 -200 0 1 +I B -150 -100 2 3 4 5 -50 -25 0 25 50 75 100 125 Temperature (_ C) Common-Mode Voltage (V) QUIESCENT CURRENT vs TEMPERATURE LARGE-SIGNAL STEP RESPONSE 25 G=1 RL = 10k Output Voltage (1V/div) 20 VS = 5.5V IQ (A) 4 Output Current (mA) 100 15 VS = 1.8V 10 5 0 +25_C +125_C 0 -50 -25 0 25 50 75 100 125 Time (50s/div) Temperature (_C) Copyright (c) 2007-2008, Texas Instruments Incorporated Product Folder Link(s): OPA333A-EP OPA2333A-EP Submit Documentation Feedback 5 OPA333A-EP,, OPA2333A-EP SGLS383B - APRIL 2007 - REVISED JUNE 2008 ............................................................................................................................................................ www.ti.com TYPICAL CHARACTERISTICS (continued) SMALL-SIGNAL STEP RESPONSE POSITIVE OVER-VOLTAGE RECOVERY Output Voltage (50mV/div) 2V/div G = +1 RL = 10k 0 Input Output 1 0k 1V/div +2 .5V 1 k 0 OPA3 33 - 2.5V Time (5s/div) Time (50s/div) SETTLING TIME vs CLOSED-LOOP GAIN NEGATIVE OVER-VOLTAGE RECOVERY 600 4V Step 500 Settling Time (s) 1V/div 2V/div Input 0 0 10 k + 2.5V 1k 400 300 200 0.001% Output O PA 333 100 0.01% - 2.5 V 0 1 Time (50s/div) 10 100 Gain (dB) SMALL-SIGNAL OVERSHOOT vs LOAD CAPACITANCE 0.1Hz TO 10Hz NOISE 40 35 25 500nV/div Overshoot (%) 30 20 15 10 5 0 10 100 1000 1s/div Load Capacitance (pF) 6 Submit Documentation Feedback Copyright (c) 2007-2008, Texas Instruments Incorporated Product Folder Link(s): OPA333A-EP OPA2333A-EP OPA333A-EP,, OPA2333A-EP www.ti.com ............................................................................................................................................................ SGLS383B - APRIL 2007 - REVISED JUNE 2008 TYPICAL CHARACTERISTICS (continued) CURRENT AND VOLTAGE NOISE SPECTRAL DENSITY vs FREQUENCY 1000 Continues with no 1/f (flicker) noise. Current Noise 100 100 Voltage Noise 10 Current Noise (fA//Hz) Voltage Noise (nV//Hz) 1000 10 1 10 100 1k 10k Frequency (Hz) Copyright (c) 2007-2008, Texas Instruments Incorporated Product Folder Link(s): OPA333A-EP OPA2333A-EP Submit Documentation Feedback 7 OPA333A-EP,, OPA2333A-EP SGLS383B - APRIL 2007 - REVISED JUNE 2008 ............................................................................................................................................................ www.ti.com APPLICATION INFORMATION The OPA333A and OPA2333A are unity-gain stable and free from unexpected output phase reversal. They use a proprietary auto-calibration technique to provide low offset voltage and very low drift over time and temperature. For lowest offset voltage and precision performance, circuit layout and mechanical conditions should be optimized. Avoid temperature gradients that create thermoelectric (Seebeck) effects in the thermocouple junctions formed from connecting dissimilar conductors. These thermally-generated potentials can be made to cancel by ensuring they are equal on both input terminals. Other layout and design considerations include: * Use low thermoelectric-coefficient conditions (avoid dissimilar metals) * Thermally isolate components from power supplies or other heat sources * Shield op amp and input circuitry from air currents, such as cooling fans Following these guidelines will reduce the likelihood of junctions being at different temperatures, which can cause thermoelectric voltages of 0.1 V/C or higher, depending on materials used. Operating Voltage The OPA333A and OPA2333A op amps operate over a power-supply range of 1.8 V to 5.5 V (0.9 V to 2.75 V). Supply voltages higher than 7 V (absolute maximum) can permanently damage the device. Parameters that vary over supply voltage or temperature are shown in the Typical Characteristics section of this data sheet. Input Voltage The OPA333A and OPA2333A input common-mode voltage range extends 0.1 V beyond the supply rails. The OPA333A is designed to cover the full range without the troublesome transition region found in some other rail-to-rail amplifiers. Normally, input bias current is about 70 pA; however, input voltages exceeding the power supplies can cause excessive current to flow into or out of the input pins. Momentary voltages greater than the power supply can be tolerated if the input current is limited to 10 mA. This limitation is easily accomplished with an input resistor(see Figure 1). Current-limiting resistor required if input voltage exceeds supply rails by 0.5V. +5V IOVERLOAD 10mA max VOUT OPA333A VIN 5k Figure 1. Input Current Protection Internal Offset Correction The OPA333A and OPA2333A op amps use an auto-calibration technique with a time-continuous 350-kHz op amp in the signal path. This amplifier is zero corrected every 8 s using a proprietary technique. Upon power up, the amplifier requires approximately 100 s to achieve specified VOS accuracy. This design has no aliasing or flicker noise. 8 Submit Documentation Feedback Copyright (c) 2007-2008, Texas Instruments Incorporated Product Folder Link(s): OPA333A-EP OPA2333A-EP OPA333A-EP,, OPA2333A-EP www.ti.com ............................................................................................................................................................ SGLS383B - APRIL 2007 - REVISED JUNE 2008 Achieving Output Swing to the Op Amp Negative Rail Some applications require output voltage swings from 0 V to a positive full-scale voltage (such as 2.5 V) with excellent accuracy. With most single-supply op amps, problems arise when the output signal approaches 0 V, near the lower output swing limit of a single-supply op amp. A good single-supply op amp may swing close to single-supply ground, but will not reach ground. The output of the OPA333A and OPA2333A can be made to swing to ground, or slightly below, on a single-supply power source. To do so requires the use of another resistor and an additional, more negative, power supply than the op amp negative supply. A pulldown resistor may be connected between the output and the additional negative supply to pull the output down below the value that the output would otherwise achieve (see Figure 2). V+ = +5V OPA333A VOUT VIN RP = 20k Op Amp V- = Gnd -5V Additional Negative Supply Figure 2. VOUT Range to Ground The OPA333A and OPA2333A have an output stage that allows the output voltage to be pulled to its negative supply rail, or slightly below, using the technique previously described. This technique only works with some types of output stages. The OPA333A and OPA2333A have been characterized to perform with this technique; however, the recommended resistor value is approximately 20 k. Note that this configuration will increase the current consumption by several hundreds of microamps. Accuracy is excellent down to 0 V and as low as -2 mV. Limiting and nonlinearity occurs below -2 mV, but excellent accuracy returns as the output is again driven above -2 mV. Lowering the resistance of the pulldown resistor allows the op amp to swing even further below the negative rail. Resistances as low as 10 k can be used to achieve excellent accuracy down to -10 mV. General Layout Guidelines Attention to good layout practices is always recommended. Keep traces short and, when possible, use a printed circuit board (PCB) ground plane with surface-mount components placed as close to the device pins as possible. Place a 0.1-F capacitor closely across the supply pins. These guidelines should be applied throughout the analog circuit to improve performance and provide benefits, such as reducing the electromagnetic interference (EMI) susceptibility. Operational amplifiers vary in their susceptibility to radio frequency interference (RFI). RFI can generally be identified as a variation in offset voltage or dc signal levels with changes in the interfering RF signal. The OPA333A has been specifically designed to minimize susceptibility to RFI and demonstrates remarkably low sensitivity compared to previous-generation devices. Strong RF fields may still cause varying offset levels. Copyright (c) 2007-2008, Texas Instruments Incorporated Product Folder Link(s): OPA333A-EP OPA2333A-EP Submit Documentation Feedback 9 OPA333A-EP,, OPA2333A-EP SGLS383B - APRIL 2007 - REVISED JUNE 2008 ............................................................................................................................................................ www.ti.com 4.096V REF3140 +5V + R9 150k 0.1F R1 6.04k R5 31.6k D1 +5V 0.1F + - R2 2.94k - + + R2 549 O PA333A R6 200 K-Type Thermocouple 40.7V/_ C R4 6.04k R3 60.4 VO Zero Adj. Figure 3. Temperature Measurement Figure 4 shows the basic configuration for a bridge amplifier. VEX R1 +5V R R R R OPA333A VOUT R1 VREF Figure 4. Single Op-Amp Bridge Amplifier A low-side current shunt monitor is shown in Figure 5. RN are operational resistors used to isolate the ADS1100 from the noise of the digital I2C bus. Since the ADS1100 is a 16-bit converter, a precise reference is essential for maximum accuracy. If absolute accuracy is not required, and the 5-V power supply is sufficiently stable, the REF3130 may be omitted. 10 Submit Documentation Feedback Copyright (c) 2007-2008, Texas Instruments Incorporated Product Folder Link(s): OPA333A-EP OPA2333A-EP OPA333A-EP,, OPA2333A-EP www.ti.com ............................................................................................................................................................ SGLS383B - APRIL 2007 - REVISED JUNE 2008 3V +5V REF3130 Load R1 4.99k R2 49.9k R6 71.5k V I LOAD RSHUNT 1 RN 56 OPA333A R3 4.99k R4 48.7k ADS1100 R7 1.18k Stray Ground-Loop Resistance RN 56 I 2C (PGA Gain = 4) FS = 3.0V NOTE: 1% resistors provide adequate common-mode rejection at small ground-loop errors. Figure 5. Low-Side Current Monitor RG RSHUNT zener(1) R1(2) 10k V+ MOSFET rated to stand-off supply voltage such as BSS84 for up to 50V. OPA333A +5V V+ Two zener biasing methods are shown.(3) Output Load RBIAS RL NOTES: (1) zener rated for op amp supply capability (that is, 5.1V for OPA333). (2) Current-limiting resistor. (3) Choose zener biasing resistor or dual NMOSFETS (FDG6301N, NTJD4001N, or Si1034) Figure 6. High-Side Current Monitor Copyright (c) 2007-2008, Texas Instruments Incorporated Product Folder Link(s): OPA333A-EP OPA2333A-EP Submit Documentation Feedback 11 OPA333A-EP,, OPA2333A-EP SGLS383B - APRIL 2007 - REVISED JUNE 2008 ............................................................................................................................................................ www.ti.com V1 -In INA152 OPA333 100 k 2 R2 5 60 k 1 M 3V 1 M 6 R1 NTC Thermistor OPA333 3 1 OPA333 V2 +In VO = (1 + 2R2/R1) (V2 - V1) Figure 7. Thermistor Measurement Figure 8. Precision Instrumentation Amplifier +VS R1 100k VO R2 f LPF = 150Hz C4 1.06nF 1/2 OPA2333 RA +VS R2 100k R6 100k 1/2 OPA2333 +VS 3 7 2 INA321(1) 4 5 R8 100k +VS dc R3 100k GINA = 5 R12 5k 6 LL 1/2 OPA2333 Wilson LA R14 1M GTOT = 1kV/V R7 100k ac +VS 1 C3 1F VOUT OPA333 R13 318k GOPA = 200 +VS 1/2 OPA2333 VCENTRAL C1 47pF (RA + LA + LL)/3 fHPF = 0.5Hz (provides ac signal coupling) 1/2 VS R5 390k +VS R4 100k R9 20k 1/2 OPA2333 RL Inverted VCM +VS VS = +2.7V to +5.5V 1/2 OPA2333 BW = 0.5Hz to 150Hz +VS R10 1M 1/2 VS C2 0.64F NOTE: (1) Other instrumentation amplifiers can be used, such as the INA326, which has lower noise, but higher quiescent current. R11 1M fO = 0.5Hz Figure 9. Single-Supply, Very-Low-Power ECG Circuit 12 Submit Documentation Feedback Copyright (c) 2007-2008, Texas Instruments Incorporated Product Folder Link(s): OPA333A-EP OPA2333A-EP PACKAGE OPTION ADDENDUM www.ti.com 24-Aug-2018 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) OPA2333AMDREP ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -55 to 125 2333EP OPA2333AMDREPG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -55 to 125 2333EP OPA333AMDBVREP ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 0 OBYM OPA333AMDCKREP ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 0 CHQ V62/07633-01XE ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -55 to 125 V62/07633-01YE ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 0 V62/07633-02ZE ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -55 to 125 OBYM CHQ 2333EP (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based flame retardants must also meet the <=1000ppm threshold requirement. (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 24-Aug-2018 (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 3-Aug-2017 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing OPA2333AMDREP SOIC OPA333AMDBVREP OPA333AMDCKREP SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 SOT-23 DBV 5 3000 179.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 SC70 DCK 5 3000 179.0 8.4 2.2 2.5 1.2 4.0 8.0 Q3 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 3-Aug-2017 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) OPA2333AMDREP SOIC D 8 2500 367.0 367.0 35.0 OPA333AMDBVREP SOT-23 DBV 5 3000 203.0 203.0 35.0 OPA333AMDCKREP SC70 DCK 5 3000 203.0 203.0 35.0 Pack Materials-Page 2 PACKAGE OUTLINE DBV0005A SOT-23 - 1.45 mm max height SCALE 4.000 SMALL OUTLINE TRANSISTOR C 3.0 2.6 1.75 1.45 PIN 1 INDEX AREA 1 0.1 C B A 5 2X 0.95 1.9 1.45 MAX 3.05 2.75 1.9 2 4 0.5 5X 0.3 0.2 3 (1.1) C A B 0.15 TYP 0.00 0.25 GAGE PLANE 8 TYP 0 0.22 TYP 0.08 0.6 TYP 0.3 SEATING PLANE 4214839/C 04/2017 NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. Refernce JEDEC MO-178. www.ti.com EXAMPLE BOARD LAYOUT DBV0005A SOT-23 - 1.45 mm max height SMALL OUTLINE TRANSISTOR PKG 5X (1.1) 1 5 5X (0.6) SYMM (1.9) 2 2X (0.95) 3 4 (R0.05) TYP (2.6) LAND PATTERN EXAMPLE EXPOSED METAL SHOWN SCALE:15X SOLDER MASK OPENING METAL SOLDER MASK OPENING METAL UNDER SOLDER MASK EXPOSED METAL EXPOSED METAL 0.07 MIN ARROUND 0.07 MAX ARROUND NON SOLDER MASK DEFINED (PREFERRED) SOLDER MASK DEFINED SOLDER MASK DETAILS 4214839/C 04/2017 NOTES: (continued) 4. Publication IPC-7351 may have alternate designs. 5. Solder mask tolerances between and around signal pads can vary based on board fabrication site. www.ti.com EXAMPLE STENCIL DESIGN DBV0005A SOT-23 - 1.45 mm max height SMALL OUTLINE TRANSISTOR PKG 5X (1.1) 1 5 5X (0.6) SYMM (1.9) 2 2X(0.95) 4 3 (R0.05) TYP (2.6) SOLDER PASTE EXAMPLE BASED ON 0.125 mm THICK STENCIL SCALE:15X 4214839/C 04/2017 NOTES: (continued) 6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. 7. Board assembly site may have different recommendations for stencil design. www.ti.com PACKAGE OUTLINE DBV0005A SOT-23 - 1.45 mm max height SCALE 4.000 SMALL OUTLINE TRANSISTOR C 3.0 2.6 1.75 1.45 PIN 1 INDEX AREA 1 0.1 C B A 5 2X 0.95 1.9 1.45 MAX 3.05 2.75 1.9 2 4 0.5 5X 0.3 0.2 3 (1.1) C A B 0.15 TYP 0.00 0.25 GAGE PLANE 8 TYP 0 0.22 TYP 0.08 0.6 TYP 0.3 SEATING PLANE 4214839/C 04/2017 NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. Refernce JEDEC MO-178. www.ti.com EXAMPLE BOARD LAYOUT DBV0005A SOT-23 - 1.45 mm max height SMALL OUTLINE TRANSISTOR PKG 5X (1.1) 1 5 5X (0.6) SYMM (1.9) 2 2X (0.95) 3 4 (R0.05) TYP (2.6) LAND PATTERN EXAMPLE EXPOSED METAL SHOWN SCALE:15X SOLDER MASK OPENING METAL SOLDER MASK OPENING METAL UNDER SOLDER MASK EXPOSED METAL EXPOSED METAL 0.07 MIN ARROUND 0.07 MAX ARROUND NON SOLDER MASK DEFINED (PREFERRED) SOLDER MASK DEFINED SOLDER MASK DETAILS 4214839/C 04/2017 NOTES: (continued) 4. Publication IPC-7351 may have alternate designs. 5. Solder mask tolerances between and around signal pads can vary based on board fabrication site. www.ti.com EXAMPLE STENCIL DESIGN DBV0005A SOT-23 - 1.45 mm max height SMALL OUTLINE TRANSISTOR PKG 5X (1.1) 1 5 5X (0.6) SYMM (1.9) 2 2X(0.95) 4 3 (R0.05) TYP (2.6) SOLDER PASTE EXAMPLE BASED ON 0.125 mm THICK STENCIL SCALE:15X 4214839/C 04/2017 NOTES: (continued) 6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. 7. Board assembly site may have different recommendations for stencil design. www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. TI's published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and services. Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyers and others who are developing systems that incorporate TI products (collectively, "Designers") understand and agree that Designers remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products used in or for Designers' applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will thoroughly test such applications and the functionality of such TI products as used in such applications. TI's provision of technical, application or other design advice, quality characterization, reliability data or other services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, "TI Resources") are intended to assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any way, Designer (individually or, if Designer is acting on behalf of a company, Designer's company) agrees to use any particular TI Resource solely for this purpose and subject to the terms of this Notice. TI's provision of TI Resources does not expand or otherwise alter TI's applicable published warranties or warranty disclaimers for TI products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections, enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically described in the published documentation for a particular TI Resource. Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. TI RESOURCES ARE PROVIDED "AS IS" AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM, INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949 and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements. Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use. Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S. TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product). Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications and that proper product selection is at Designers' own risk. Designers are solely responsible for compliance with all legal and regulatory requirements in connection with such selection. Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer's noncompliance with the terms and provisions of this Notice. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2018, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: V62/07633-01XE V62/07633-01YE OPA333AMDBVREP OPA333AMDCKREP OPA333AMDBVREPG4