LM317L, NCV317L 100 mA Adjustable Output, Positive Voltage Regulator The LM317L is an adjustable 3-terminal positive voltage regulator capable of supplying in excess of 100 mA over an output voltage range of 1.2 V to 37 V. This voltage regulator is exceptionally easy to use and requires only two external resistors to set the output voltage. Further, it employs internal current limiting, thermal shutdown and safe area compensation, making them essentially blow-out proof. The LM317L serves a wide variety of applications including local, on card regulation. This device can also be used to make a programmable output regulator, or by connecting a fixed resistor between the adjustment and output, the LM317L can be used as a precision current regulator. www.onsemi.com LOW CURRENT THREE-TERMINAL ADJUSTABLE POSITIVE VOLTAGE REGULATOR Features * * * * * * * * * * Output Current in Excess of 100 mA Output Adjustable Between 1.2 V and 37 V Internal Thermal Overload Protection Internal Short Circuit Current Limiting Output Transistor Safe-Area Compensation Floating Operation for High Voltage Applications Standard 3-Lead Transistor Package Eliminates Stocking Many Fixed Voltages NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC-Q100 Qualified and PPAP Capable These are Pb-Free Devices Simplified Application Vin Vout LM317L R1 240 Pin 1. 2. 3. 4. 5. 6. 7. 8. 8 1 SOIC-8 D SUFFIX CASE 751 12 1 Vin Vout Vout Adjust N.C. Vout Vout N.C. 2 3 STRAIGHT LEAD BULK PACK 3 BENT LEAD TAPE & REEL AMMO PACK TO-92 Z SUFFIX CASE 29 Pin 1. Adjust 2. Vout 3. Vin IAdj Adjust Cin* 0.1mF + C ** O 1.0mF ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 9 of this data sheet. R2 * Cin is required if regulator is located an appreciable ** distance from power supply filter. ** CO is not needed for stability, however, ** it does improve transient response. R Vout + 1.25V 1 ) 2 ) IAdjR2 R1 Since IAdj is controlled to less than 100 mA, the error associated with this term is negligible in most applications. (c) Semiconductor Components Industries, LLC, 2013 May, 2017 - Rev. 13 1 Publication Order Number: LM317L/D LM317L, NCV317L MAXIMUM RATINGS Symbol Value Unit Input-Output Voltage Differential Rating VI-VO 40 Vdc Power Dissipation Case 29 (TO-92) TA = 25C Thermal Resistance, Junction-to-Ambient Thermal Resistance, Junction-to-Case PD RqJA RqJC Internally Limited 160 83 W C/W C/W Case 751 (SOIC-8) (Note 1) TA = 25C Thermal Resistance, Junction-to-Ambient Thermal Resistance, Junction-to-Case PD RqJA RqJC Internally Limited 180 45 W C/W C/W TJMAX +150 C Tstg -65 to +150 C Maximum Junction Temperature Storage Temperature Range Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 1. SOIC-8 Junction-to-Ambient Thermal Resistance is for minimum recommended pad size. Refer to Figure 24 for Thermal Resistance variation versus pad size. 2. This device series contains ESD protection and exceeds the following tests: Human Body Model, 2000 V per MIL STD 883, Method 3015. Machine Model Method, 200 V. Vin 300 300 300 3.0k 70 300 6.8V 6.8V 350 18k 8.67k 500 130 400 5.1k 200k 6.3V 180 180 2.0k 6.0k 60 10 p 10 F p F Vout 2.4k 12.8k Figure 1. Representative Schematic Diagram www.onsemi.com 2 2.5 50 Adjust LM317L, NCV317L ELECTRICAL CHARACTERISTICS (VI-VO = 5.0 V; IO = 40 mA; TJ = Tlow to Thigh (Note 3); Imax and Pmax (Note 4); unless otherwise noted.) LM317L, LB, NCV317LB Characteristics Figure Symbol Min Typ Max Unit Line Regulation (Note 5) TA = 25C, 3.0 V VI - VO 40 V 1 Regline - 0.01 0.04 %/V Load Regulation (Note 5), TA = 25C 10 mA IO Imax - LM317L VO 5.0 V VO 5.0 V 2 Regload - - 5.0 0.1 25 0.5 mV % VO Adjustment Pin Current 3 IAdj - 50 100 mA Adjustment Pin Current Change 2.5 V VI - VO 40 V, PD Pmax 10 mA IO Imax - LM317L 1, 2 DIAdj - 0.2 5.0 mA Reference Voltage 3.0 V VI - VO 40 V, PD Pmax 10 mA IO Imax - LM317L 3 Vref 1.20 1.25 1.30 V Line Regulation (Note 5), 3.0 V VI - VO 40 V 1 Regline - 0.02 0.07 %/V Load Regulation (Note 5) 10 mA IO Imax - LM317L VO 5.0 V VO 5.0 V 2 Regload - - 20 0.3 70 1.5 mV % VO Temperature Stability (Tlow TJ Thigh) 3 TS - 0.7 - % VO Minimum Load Current to Maintain Regulation (VI - VO = 40 V) 3 ILmin - 3.5 10 mA Maximum Output Current VI - VO 6.25 V, PD Pmax, Z Package VI - VO 40 V, PD Pmax, TA = 25C, Z Package 3 Imax 100 - 200 20 - - RMS Noise, % of VO TA = 25C, 10 Hz f 10 kHz - N - 0.003 - Ripple Rejection (Note 6) VO = 1.2 V, f = 120 Hz CAdj = 10 mF, VO = 10.0 V 4 RR 60 - 80 80 - - Thermal Shutdown (Note 7) - - - 180 - C Long Term Stability, TJ = Thigh (Note 8) TA = 25C for Endpoint Measurements 3 S - 0.3 1.0 %/1.0 k Hrs. 3. 4. 5. mA % VO dB Tlow to Thigh = 0 to +125C for LM317L -40 to +125C for LM317LB, NCV317LB Pmax = 625 mW Imax = 100 mA Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. 6. CAdj, when used, is connected between the adjustment pin and ground. 7. Thermal characteristics are not subject to production test. 8. Since Long-Term Stability cannot be measured on each device before shipment, this specification is an engineering estimate of average stability from lot to lot. www.onsemi.com 3 LM317L, NCV317L VCC VOH - VOL VOL Line Regulation (%/V) = * x 100 VIH VIL VOH VOL Vout Vin LM317L Adjust Cin 0.1mF 240 1% R1 RL + CO IAdj 1mF R2 1 % *Pulse Testing Required: 1% Duty Cycle is suggested. Figure 2. Line Regulation and DIAdj/Line Test Circuit Load Regulation (mV) = VO (min Load) -VO (max Load) VO (min Load) - VO (max Load) Load Regulation (% VO) = VO (min Load) Vin* Vin LM317L Vout Adjust X 100 IL R1 RL (max Load) 240 1% * + Cin 0.1mF VO (min Load) VO (max Load) CO IAdj RL (min Load) 1.0mF R2 1% *Pulse Testing Required: 1% Duty Cycle is suggested. Figure 3. Load Regulation and DIAdj/Load Test Circuit Vin Vout Adjust R1 IAdj VI Cin IL LM317L 240 1% Vref CO 0.1mF ISET Pulse Testing Required: 1% Duty Cycle is suggested. RL + To Calculate R2: Vout = ISET R2 + 1.250 V Assume ISET = 5.25 mA R2 1% Figure 4. Standard Test Circuit www.onsemi.com 4 1mF VO LM317L, NCV317L 14.30V Vout Vin 4.30V f = 120 Hz Vout = 1.25 V LM317L Adjust Cin D1 * 1N4002 240 1% R1 RL + CO 0.1mF R2 VO 1mF + 1.65K 1% 10mF ** *D1 Discharges CAdj if Output is Shorted to Ground. **CAdj provides an AC ground to the adjust pin. 0.4 Vin = 45 V Vout = 5.0 V IL = 5.0 mA to 40 mA 0.2 RR, RIPPLE REJECTION (dB) V out, OUTPUT VOLTAGE CHANGE (%) Figure 5. Ripple Rejection Test Circuit 0 -0.2 Vin = 10 V Vout = 5.0 V IL = 5.0 mA to 100 mA -0.4 -0.6 -0.8 80 70 IL = 40 mA f = 120 Hz Vout = 10 V Vin = 14 V to 24 V 60 50 -1.0 -50 -25 0 25 50 75 100 125 TJ, JUNCTION TEMPERATURE (C) -50 150 -25 Figure 6. Load Regulation V in -Vout , INPUT-OUTPUT VOLTAGE DIFFERENTIAL (V) 2.5 TJ = 25C IO, OUTPUT CURRENT (A) 150 Figure 7. Ripple Rejection 0.50 0.40 0.30 0.20 TJ = 150C 0.10 0 0 25 50 75 100 125 TJ, JUNCTION TEMPERATURE (C) 0 10 20 30 40 Vin-Vout, INPUT-OUTPUT VOLTAGE DIFFERENTIAL (V) 2.0 IL = 100 mA 1.5 IL = 5.0 mA 1.0 0.5 50 Figure 8. Current Limit -50 -25 0 25 50 75 100 125 TJ, JUNCTION TEMPERATURE (C) Figure 9. Dropout Voltage www.onsemi.com 5 150 LM317L, NCV317L 100 4.5 90 RR, RIPPLE REJECTION (dB) IB , QUIESCENT CURRENT (mA) 5.0 TJ = 55C TJ = 25C TJ = 150C 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 IL = 40 mA Vin = 5.0 V 1.0 VPP Vout = 1.25 V 80 70 60 50 40 30 20 10 0 10 10 20 30 40 Vin-Vout, INPUT-OUTPUT VOLTAGE DIFFERENTIAL (V) Figure 10. Minimum Operating Current IAdj, ADJUSTMENT PIN CURRENT ( A) V ref , REFERENCE VOLTAGE (V) 10 k 100 k 1.0 M f, FREQUENCY (Hz) 80 1.250 1.240 Vin = 4.2 V Vout = Vref IL = 5.0 mA 1.230 -50 -25 0 25 50 75 100 125 TJ, JUNCTION TEMPERATURE (C) 65 60 55 50 45 40 35 150 Vin = 6.25 V Vout = Vref IL = 10 mA IL = 100 mA 70 -50 Figure 12. Temperature Stability 0.4 Vin = 4.25 V to 41.25 V Vout = Vref IL = 5 mA 0.2 -25 0 25 50 75 100 125 TJ, JUNCTION TEMPERATURE (C) 150 Figure 13. Adjustment Pin Current NOISE VOLTAGE ( V) Vout , OUTPUT VOLTAGE CHANGE (%) 1.0 k Figure 11. Ripple Rejection versus Frequency 1.260 1.220 100 0 -0.2 -0.4 -0.6 Bandwidth 100 Hz to 10 kHz 10 8.0 6.0 -0.8 -1.0 4.0 -50 -25 0 25 50 75 100 125 TJ, JUNCTION TEMPERATURE (C) 150 -50 Figure 14. Line Regulation -25 0 25 50 75 100 125 TJ, JUNCTION TEMPERATURE (C) Figure 15. Output Noise www.onsemi.com 6 150 Vout , OUTPUT VOLTAGE DEVIATION (V) 1.5 1.0 CL = 1.0 mF; CAdj = 10 mF 0.5 0 -0.5 Vout = 10 V IL = 50 mA TJ = 25C V in , INPUT VOTLAGE CHANGE (V) -1.0 -1.5 1.0 Vin 0.5 0 0.3 0.2 CL = 1 mF; CAdj = 10 mF 0.1 Vin = 15 V Vout = 10 V INL = 50 mA TJ = 25C 0 -0.1 CL = 0.3 mF; CAdj = 10 mF -0.2 CL = 0; Without CAdj I L , LOAD CURRENT (mA) Vout , OUTPUT VOLTAGE DEVIATION (V) LM317L, NCV317L -0.3 100 IL 50 0 t, TIME (ms) 20 t, TIME (ms) Figure 16. Line Transient Response Figure 17. Load Transient Response 0 10 20 30 40 0 10 30 40 APPLICATIONS INFORMATION Basic Circuit Operation Load Regulation The LM317L is a 3-terminal floating regulator. In operation, the LM317L develops and maintains a nominal 1.25 V reference (Vref) between its output and adjustment terminals. This reference voltage is converted to a programming current (IPROG) by R1 (see Figure 13), and this constant current flows through R2 to ground. The regulated output voltage is given by: The LM317L is capable of providing extremely good load regulation, but a few precautions are needed to obtain maximum performance. For best performance, the programming resistor (R1) should be connected as close to the regulator as possible to minimize line drops which effectively appear in series with the reference, thereby degrading regulation. The ground end of R2 can be returned near the load ground to provide remote ground sensing and improve load regulation. Vout = Vref (1 + R2 ) + IAdj R2 R1 Since the current from the adjustment terminal (IAdj) represents an error term in the equation, the LM317L was designed to control IAdj to less than 100 mA and keep it constant. To do this, all quiescent operating current is returned to the output terminal. This imposes the requirement for a minimum load current. If the load current is less than this minimum, the output voltage will rise. Since the LM317L is a floating regulator, it is only the voltage differential across the circuit which is important to performance, and operation at high voltages with respect to ground is possible. Vin External Capacitors A 0.1 mF disc or 1.0 mF tantalum input bypass capacitor (Cin) is recommended to reduce the sensitivity to input line impedance. The adjustment terminal may be bypassed to ground to improve ripple rejection. This capacitor (CAdj) prevents ripple from being amplified as the output voltage is increased. A 10 mF capacitor should improve ripple rejection about 15 dB at 120 Hz in a 10 V application. Although the LM317L is stable with no output capacitance, like any feedback circuit, certain values of external capacitance can cause excessive ringing. An output capacitance (CO) in the form of a 1.0 mF tantalum or 25 mF aluminum electrolytic capacitor on the output swamps this effect and insures stability. Vout LM317L + R1 Vref Adjust IPROG Vout IAdj R2 Vref = 1.25 V Typical Figure 18. Basic Circuit Configuration www.onsemi.com 7 LM317L, NCV317L Protection Diodes D1 When external capacitors are used with any IC regulator it is sometimes necessary to add protection diodes to prevent the capacitors from discharging through low current points into the regulator. Figure 14 shows the LM317L with the recommended protection diodes for output voltages in excess of 25 V or high capacitance values (CO > 10 mF, CAdj > 5.0 mF). Diode D1 prevents CO from discharging thru the IC during an input short circuit. Diode D2 protects against capacitor CAdj discharging through the IC during an output short circuit. The combination of diodes D1 and D2 prevents CAdj from discharging through the IC during an input short circuit. 1N4002 Vin Vout LM317L + Cin R1 CO D2 Adjust 1N4002 R2 CAdj Figure 19. Voltage Regulator with Protection Diodes +25V Vout LM317L 1.25k Vin Adjust D1 1N4002 D1 1N914 R2 500 * To provide current limiting of IO to the system ground, the source of the current limiting diode must be tied to a negative voltage below - 7.25 V. Vin Vout LM317L D2 1N914 + 1.0mF 120 Adjust MPS2222 1N5314 Vref R2 IDSS R1 = IO VO R1 TTL Control 720 1.0k VSS* Vref IOmax + IDSS Minimum Vout = 1.25 V VO < POV + 1.25 V + VSS ILmin - IP < IO < 100 mA - IP As shown O < IO < 95 mA D1 protects the device during an input short circuit. Figure 20. Adjustable Current Limiter Figure 21. 5.0 V Electronic Shutdown Regulator R1 Vin Iout R2 LM317L Vout IAdj Adjust Vout Vin LM317L 240 Ioutmax = Vref R1 Ioutmax = Vref R1 + R2 50k Adjust R2 1N4002 MPS2907 + 10mF + IAdj ^ 1.25 V R1 + IAdj ^ 1.25 V R1 + R2 5.0 mA < Iout < 100 mA Figure 22. Slow Turn-On Regulator Figure 23. Current Regulator www.onsemi.com 8 JUNCTION-TO-AIR ( C/W) R JA, THERMAL RESISTANCE 170 3.2 150 2.8 PD(max) for TA = 50C 130 110 2.4 III II IIIIIIII IIIIIIII 2.0 Graph represents symmetrical layout 90 L 70 1.6 2.0 oz. Copper L 1.2 3.0 mm 0.8 50 RJA 30 0 10 0.4 20 30 40 PD, MAXIMUM POWER DISSIPATION (W) LM317L, NCV317L 50 L, LENGTH OF COPPER (mm) Figure 24. SOP-8 Thermal Resistance and Maximum Power Dissipation versus P.C.B. Copper Length ORDERING INFORMATION Package Shipping LM317LBDG SOIC-8 (Pb-Free) 98 Units / Rail LM317LBDR2G SOIC-8 (Pb-Free) 2500/Tape & Reel LM317LBZG TO-92 (Pb-Free) 2000 Units / Bag LM317LBZRAG TO-92 (Pb-Free) 2000 Tape & Reel TO-92 (Pb-Free) 2000 Ammo Pack NCV317LBDG* SOIC-8 (Pb-Free) 98 Units / Rail NCV317LBDR2G* SOIC-8 (Pb-Free) 2500/Tape & Reel NCV317LBZG* TO-92 (Pb-Free) 2000 Units / Bag NCV317LBZRAG* TO-92 (Pb-Free) 2000 Tape & Reel LM317LDG SOIC-8 (Pb-Free) 98 Units / Rail LM317LDR2G SOIC-8 (Pb-Free) 2500/Tape & Reel LM317LZG TO-92 (Pb-Free) 2000 Units / Bag Device LM317LBZRPG LM317LZRAG Operating Temperature Range TJ = -40C to +125C TO-92 (Pb-Free) 2000 Tape & Reel LM317LZREG TO-92 (Pb-Free) 2000 Tape & Reel LM317LZRMG TO-92 (Pb-Free) 2000 Ammo Pack LM317LZRPG TO-92 (Pb-Free) 2000 Ammo Pack TJ = 0C to +125C For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *NCV devices: Tlow = -40C, Thigh = +125C. Guaranteed by design. NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC-Q100 Qualified and PPAP Capable. www.onsemi.com 9 LM317L, NCV317L PACKAGE DIMENSIONS TO-92 (TO-226) Z SUFFIX CASE 29-11 ISSUE AM A B STRAIGHT LEAD BULK PACK R P NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. CONTOUR OF PACKAGE BEYOND DIMENSION R IS UNCONTROLLED. 4. LEAD DIMENSION IS UNCONTROLLED IN P AND BEYOND DIMENSION K MINIMUM. L SEATING PLANE K D X X G J H V C SECTION X-X 1 N DIM A B C D G H J K L N P R V INCHES MIN MAX 0.175 0.205 0.170 0.210 0.125 0.165 0.016 0.021 0.045 0.055 0.095 0.105 0.015 0.020 0.500 --0.250 --0.080 0.105 --0.100 0.115 --0.135 --- MILLIMETERS MIN MAX 4.45 5.20 4.32 5.33 3.18 4.19 0.407 0.533 1.15 1.39 2.42 2.66 0.39 0.50 12.70 --6.35 --2.04 2.66 --2.54 2.93 --3.43 --- N A R BENT LEAD TAPE & REEL AMMO PACK B P NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. CONTOUR OF PACKAGE BEYOND DIMENSION R IS UNCONTROLLED. 4. LEAD DIMENSION IS UNCONTROLLED IN P AND BEYOND DIMENSION K MINIMUM. T SEATING PLANE K D X X G J V 1 C SECTION X-X N www.onsemi.com 10 DIM A B C D G J K N P R V MILLIMETERS MIN MAX 4.45 5.20 4.32 5.33 3.18 4.19 0.40 0.54 2.40 2.80 0.39 0.50 12.70 --2.04 2.66 1.50 4.00 2.93 --3.43 --- LM317L, NCV317L PACKAGE DIMENSIONS SOIC-8 NB D SUFFIX CASE 751-07 ISSUE AK NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. 751-01 THRU 751-06 ARE OBSOLETE. NEW STANDARD IS 751-07. -X- A 8 5 S B 0.25 (0.010) Y M M 1 4 K -Y- G C N DIM A B C D G H J K M N S X 45 _ SEATING PLANE -Z- 0.10 (0.004) H M D 0.25 (0.010) M Z Y S X J S MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.33 0.51 1.27 BSC 0.10 0.25 0.19 0.25 0.40 1.27 0_ 8_ 0.25 0.50 5.80 6.20 INCHES MIN MAX 0.189 0.197 0.150 0.157 0.053 0.069 0.013 0.020 0.050 BSC 0.004 0.010 0.007 0.010 0.016 0.050 0 _ 8 _ 0.010 0.020 0.228 0.244 SOLDERING FOOTPRINT* 1.52 0.060 7.0 0.275 4.0 0.155 0.6 0.024 1.270 0.050 SCALE 6:1 mm inches *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. "Typical" parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor 19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5817-1050 www.onsemi.com 11 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative LM317L/D