OPA OPA343 OPA2343 OPA4343 OPA 234 3 434 (R) 3 OPA 434 3 www.ti.com SINGLE-SUPPLY, RAIL-TO-RAIL OPERATIONAL AMPLIFIERS microAmplifier TM Series FEATURES APPLICATIONS DRIVING A/D CONVERTERS PCMCIA CARDS DATA ACQUISITION AUDIO PROCESSING COMMUNICATIONS ACTIVE FILTERS TEST EQUIPMENT RAIL-TO-RAIL INPUT/OUTPUT MICRO SIZE PACKAGES WIDE BANDWIDTH: 5.5MHz HIGH SLEW RATE: 6V/s LOW THD+NOISE: 0.0007% (f = 1kHz) LOW QUIESCENT CURRENT: 850A/chan SINGLE, DUAL, AND QUAD VERSIONS The OPA343 series operates on a single supply as low as 2.5V, and input common-mode voltage range extends 500mV beyond the supply rails. Output voltage swings to within 1mV of the supply rails with a 100k load. They offer excellent dynamic response (BW = 5.5MHz, SR = 6V/s), yet quiescent current is only 850A. Dual and quad designs feature completely independent circuitry for lowest crosstalk and freedom from interaction. The single (OPA343) packages are the tiny SOT-23-5 surface mount and SO-8 surface mount. The dual (OPA2343) comes in the miniature MSOP-8 surface mount and SO-8 surface mount. The quad (OPA4343) packages are the space-saving SSOP-16 surface mount, SO-14 surface mount, and TSSOP-14 surface mount. All are specified from -40C to +85C and operate from -55C to +125C. A SPICE macromodel is available for design analysis. DESCRIPTION OPA343 series rail-to-rail CMOS operational amplifiers are designed for low-cost, miniature applications. They are optimized for low-voltage, single-supply operation. Rail-to-rail input/output and high-speed operation make them ideal for driving sampling Analog-to-Digital (A/D) converters. They are also well suited for general-purpose and audio applications as well as providing I/V conversion at the output of Digital-to-Analog (D/A) converters. Single, dual, and quad versions have identical specifications for design flexibility. OPA343 OPA343 NC 1 8 NC -In 2 7 V+ Out 1 5 V+ 4 -In V- 2 +In 3 6 Output V- 4 5 NC +In 3 OPA4343 OPA4343 SOT-23-5 Out A 1 16 Out D Out A 1 14 Out D -In A 2 15 -In D -In A 2 13 -In D +In A 3 14 +In D +In A 3 12 +In D +V 4 13 -V 12 +In C SO-8 OPA2343 A Out A 1 -In A 2 +In A V- 3 A B 4 A D D 8 V+ 7 Out B V+ 4 11 V- +In B 5 -In B +In B 5 10 +In C -In B 6 11 -In C -In B 6 9 -In C Out B 7 10 Out C Out B 7 8 Out C NC 8 9 NC 6 5 +In B B B SO-8, MSOP-8 Copyright (c) 2000, Texas Instruments Incorporated C TSSOP-14 SBOS090A C SSOP-16 Printed in U.S.A. October, 2000 SPECIFICATIONS: VS = 2.7V to 5.5V Boldface limits apply over the specified temperature range, TA = -40C to +85C. VS = 5V. At TA = +25C, RL = 10k connected to VS /2 and VOUT = VS /2, unless otherwise noted. OPA343NA, UA OPA2343EA, UA OPA4343EA, UA, NA PARAMETER OFFSET VOLTAGE Input Offset Voltage vs Temperature vs Power Supply Over Temperature Channel Separation, dc INPUT BIAS CURRENT Input Bias Current Over Temperature Input Offset Current NOISE Input Voltage Noise, f = 0.1 to 50kHz Input Voltage Noise Density, f = 1kHz Current Noise Density, f = 1kHz INPUT VOLTAGE RANGE Common-Mode Voltage Range Common-Mode Rejection Ratio CONDITION VOS dVOS/dT PSRR MIN VS = 5V VS = 2.7V to 5.5V, VCM = 0V VS = 2.7V to 5.5V, VCM = 0V mV V/C V/V V/V V/V 0.2 en in 8 25 3 VCM CMRR AOL GBW SR THD+N Over Temperature TEMPERATURE RANGE Specified Range Operating Range Storage Range Thermal Resistance SOT-23-5 Surface Mount MSOP-8 Surface Mount SO-8 Surface Mount SSOP-16 Surface Mount SO-14 Surface Mount TSSOP-14 Surface Mount 8 IOS OUTPUT Voltage Output Swing from Rail(3) Over Temperature POWER SUPPLY Specified Voltage Range Operating Voltage Range Quiescent Current (per amplifier) Over Temperature 2 3 40 0.2 Over Temperature Over Temperature Short-Circuit Current Capacitive Load Drive UNITS IB Over Temperature FREQUENCY RESPONSE Gain-Bandwidth Product Slew Rate Settling Time, 0.1% 0.01% Overload Recovery Time Total Harmonic Distortion + Noise MAX 200 200 0.2 -0.3V < VCM < (V+) - 1.8V VS = 5V, -0.3V < VCM < 5.3V VS = 2.7V, -0.3V < VCM < 3V -0.3 74 60 54 INPUT IMPEDANCE Differential Common-Mode OPEN-LOOP GAIN Open-Loop Voltage Gain Over Temperature TYP(1) RL = 100k, 5mV < VO < (V+) - 5mV RL = 100k, 5mV < VO < (V+) - 5mV RL = 10k, 50mV < VO < (V+) - 50mV RL = 10k, 50mV < VO < (V+) - 50mV RL = 2k, 200mV < VO < (V+) - 200mV RL = 2k, 200mV < VO < (V+) - 200mV 100 100 100 100 92 92 10 Vrms nV/Hz fA/Hz (V+) + 0.3 V dB dB dB 1013 || 3 1013 || 6 || pF || pF 120 dB dB dB dB dB dB 117 110 5.5 6 1 1.6 0.2 0.0007 RL = 100k, AOL 100dB RL = 100k, AOL 100dB RL = 10k, AOL 100dB RL = 10k, AOL 100dB RL = 2k, AOL 92dB RL = 2k, AOL 92dB 1 MHz V/s s s s % 10 40 5 5 50 50 200 200 mV mV mV mV mV mV mA 5 1.25 1.4 V V mA mA +85 +125 +150 C C C 50 See Typical Curve ISC CLOAD IQ pA pA pA 92 75 70 G=1 VS = 5V, G = 1, CL = 100pF VS = 5V, 2V Step, CL = 100pF VS = 5V, 2V Step, CL = 100pF VIN * G = VS VS = 5V, VO = 3Vp-p(2), G = 1, f = 1kHz VS 10 60 2.7 2.5 to 5.5 0.85 IO = 0, VS = +5V IO = 0, VS = +5V -40 -55 -65 JA C/W C/W C/W C/W C/W C/W 200 150 150 100 100 125 NOTES: (1) VS = +5V. (2) VOUT = 0.25V to 3.25V. (3) Output voltage swings are measured between the output and power supply rails. 2 OPA343, 2343, 4343 SBOS090A ABSOLUTE MAXIMUM RATINGS(1) ELECTROSTATIC DISCHARGE SENSITIVITY Supply Voltage ................................................................................... 7.5V Signal Input Terminals, Voltage(2) ..................... (V-) -0.5V to (V+) +0.5V Current(2) .................................................... 10mA Output Short-Circuit(3) .............................................................. Continuous Operating Temperature .................................................. -55C to +125C Storage Temperature ..................................................... -65C to +150C Junction Temperature ...................................................................... 150C Lead Temperature (soldering, 10s) ................................................. 300C This integrated circuit can be damaged by ESD. Burr-Brown recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. NOTES: (1) Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. (2) Input terminals are diode-clamped to the power supply rails. Input signals that can swing more than 0.5V beyond the supply rails should be current-limited to 10mA or less. (3) Short-circuit to ground, one amplifier per package. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. PACKAGE/ORDERING INFORMATION PRODUCT PACKAGE PACKAGE DRAWING NUMBER Single OPA343NA 5-Lead SOT-23-5 331 -40C to +85C B43 " " " " " OPA343UA SPECIFIED TEMPERATURE RANGE PACKAGE MARKING ORDERING NUMBER(1) TRANSPORT MEDIA OPA343NA/250 OPA343NA /3K OPA343UA OPA343UA /2K5 Tape and Reel Tape and Reel Rails Tape and Reel OPA2343EA /250 OPA2343EA/2K5 OPA2343UA OPA2343UA/2K5 Tape and Reel Tape and Reel Rails Tape and Reel OPA4343EA /250 OPA4343EA /2K5 OPA4343UA OPA4343UA /2K5 OPA4343NA/250 OPA4343NA/2K5 Tape and Reel Tape and Reel Rails Tape and Reel Tape and Reel Tape and Reel SO-8 Surface-Mount 182 -40C to +85C OPA343UA " " " " " Dual OPA2343EA MSOP-8 Surface-Mount 337 -40C to +85C C43 " " " " " OPA2343UA " SO-8 Surface-Mount 182 -40C to +85C OPA2343UA " " " " SSOP-16 Surface-Mount 322 -40C to +85C OPA4343EA " " " " SO-14 Surfac-Mount 235 -40C to +85C OPA4343UA " " " " TSSOP-14 Surface-Mount " 357 " -40C to +85C " OPA4343NA " Quad OPA4343EA " OPA4343UA " OPA4343NA " NOTE: (1) Models with a slash (/) are available only in Tape and Reel in the quantities indicated (e.g., /2K5 indicates 2500 devices per reel). Ordering 2500 pieces of "OPA2343EA/2K5" will get a single 2500 piece Tape and Reel. The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user's own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support devices and/or systems. OPA343, 2343, 4343 SBOS090A 3 TYPICAL PERFORMANCE CURVES At TA = +25C, VS = +5V, and RL = 10k connected to VS/2, unless otherwise noted. POWER-SUPPLY and COMMON-MODE REJECTION vs FREQUENCY OPEN-LOOP GAIN/PHASE vs FREQUENCY 160 0 100 PSRR 140 80 -90 60 40 -135 PSRR, CMRR (dB) -45 100 Phase () Voltage Gain (dB) 120 80 20 60 40 CMRR VCM = -0.3V to (V+) -1.8V 20 0 -180 -20 0 0.1 1 10 100 1k 10k 100k 1M 10M 1 10 100 Frequency (Hz) 1k 10k 100k 1M Frequency (Hz) INPUT VOLTAGE AND CURRENT NOISE SPECTRAL DENSITY vs FREQUENCY CHANNEL SEPARATION vs FREQUENCY 140 1k 10k 10 100 1 10 Channel Separation (dB) 100 Voltage Noise Current Noise (fAHz) Voltage Noise (nVHz) Current Noise 1k 1 10 100 1k 10k 100k 120 Dual and quad devices. G = 1, all channels. Quad measured channel A to D or B to C--other combinations yield improved rejection. 110 100 0.1 1 130 10 1M 100 1k TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY CLOSED-LOOP OUTPUT IMPEDANCE vs FREQUENCY 5k G = 100 RL = 600 0.01 G = 10 RL = 10k RL = 600 0.001 RL = 2k G=1 RL = 10k 0.0001 Output Resistance () 4k RL = 2k THD+N (%) 100k Frequency (Hz) 0.1 G = 10 3k 2k G=1 1k 0 20 100 1k Frequency (Hz) 4 10k Frequency (Hz) 10k 20k 10 100 1k 10k 100k 1M 10M Frequency (Hz) OPA343, 2343, 4343 SBOS090A TYPICAL PERFORMANCE CURVES (Cont.) At TA = +25C, VS = +5V, and RL = 10k connected to VS/2, unless otherwise noted. OPEN-LOOP GAIN AND POWER-SUPPLY REJECTION vs TEMPERATURE COMMON-MODE REJECTION vs TEMPERATURE 100 130 AOL, PSRR (dB) 110 RL = 100k 90 RL = 10k 80 CMRR (dB) AOL 120 RL = 2k 100 70 60 PSRR 90 VS = 2.7V to 5V, VCM = -0.3V to (V+) -1.8V VS = 5V, VCM = -0.3V to 5.3V VS = 2.7V, VCM = -0.3V to 3V 50 40 80 -75 -50 -25 0 25 50 75 100 -75 125 -50 -25 50 75 100 125 900 Per Amplifier Per Amplifier 1000 Quiescent Current (A) Quiescent Current (A) 25 QUIESCENT CURRENT vs SUPPLY VOLTAGE QUIESCENT CURRENT vs TEMPERATURE 1100 900 800 700 600 850 800 750 700 -75 -50 -25 0 25 50 75 100 2.0 125 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 Supply Voltage (V) Temperature (C) SHORT-CIRCUIT CURRENT vs SUPPLY VOLTAGE SHORT-CIRCUIT CURRENT vs TEMPERATURE 60 100 Short-Circuit Current (mA) -ISC 90 Short-Circuit Current (mA) 0 Temperature (C) Temperature (C) 80 70 60 50 +ISC 40 30 20 -ISC 50 +ISC 40 10 30 0 -75 -50 -25 0 25 50 Temperature (C) OPA343, 2343, 4343 SBOS090A 75 100 125 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 Supply Voltage (V) 5 TYPICAL PERFORMANCE CURVES (Cont.) At TA = +25C, VS = +5V, and RL = 10k connected to VS/2, unless otherwise noted. INPUT BIAS CURRENT vs INPUT COMMON-MODE VOLTAGE INPUT BIAS CURRENT vs TEMPERATURE 1000 1.0 0.6 100 Input Bias Current (pA) Input Bias Current (pA) 0.8 10 1 0.4 0.2 0 -0.2 -0.4 -0.6 -0.8 0.1 -1.0 -60 -40 -20 0 20 40 60 80 100 -1 0 1 Temperature (C) OUTPUT VOLTAGE SWING vs OUTPUT CURRENT +25C -55C Output Voltage (Vp-p) Output Voltage (V) 3 2 +125C 10 20 30 40 50 60 70 80 90 100 VS = 2.7V 3 2 1M 10M Frequency (Hz) OFFSET VOLTAGE PRODUCTION DISTRIBUTION OFFSET VOLTAGE DRIFT PRODUCTION DISTRIBUTION 30 25 Typical production distribution of packaged units. Percent of Amplifiers (%) Percent of Amplifiers (%) 6 4 Output Current (mA) 25 5 Maximum output voltage without slew rate-induced distortion. 0 100k 0 0 4 1 -55C +25C VS = 5.5V 5 4 1 3 MAXIMUM OUTPUT VOLTAGE vs FREQUENCY 6 5 +125C 2 Common-Mode Voltage (V) 20 15 10 5 0 Typical production distribution of packaged units. 20 15 10 5 0 -8 -7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 8 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Offset Voltage Drift (V/C) Offset Voltage (mV) 6 OPA343, 2343, 4343 SBOS090A TYPICAL PERFORMANCE CURVES (Cont.) At TA = +25C, VS = +5V, and RL = 10k connected to VS/2, unless otherwise noted. LARGE-SIGNAL STEP RESPONSE CL = 100pF CL = 100pF 1V/div 50mV/div SMALL-SIGNAL STEP RESPONSE 1s/div 1s/div SETTLING TIME vs CLOSED-LOOP GAIN SMALL-SIGNAL OVERSHOOT vs LOAD CAPACITANCE 100 60 G = -1 0.01% Settling Time (s) Overshoot (%) 50 G = +1 40 30 G = 5 20 10 0.1% 1 See text for reducing overshoot. 10 0.1 0 100 1000 Load Capacitance (pF) OPA343, 2343, 4343 SBOS090A 10k 1 10 100 1000 Closed-Loop Gain (V/V) 7 APPLICATIONS INFORMATION OPERATING VOLTAGE OPA343 series op amps are fabricated on a state-of-the-art 0.6 micron CMOS process. They are unity-gain stable and suitable for a wide range of general-purpose applications. Rail-to-rail input/output make them ideal for driving sampling A/D converters. In addition, excellent ac performance makes them well-suited for audio applications. The class AB output stage is capable of driving 600 loads connected to any point between V+ and ground. OPA343 series op amps are fully specified from +2.7V to +5V. However, supply voltage may range from +2.5V to +5.5V. Parameters are guaranteed over the specified supply range--a unique feature of the OPA343 series. In addition, many specifications apply from -40C to +85C. Most behavior remains virtually unchanged throughout the full operating voltage range. Parameters which vary significantly with operating voltages or temperature are shown in the Typical Performance Curves. Rail-to-rail input and output swing significantly increases dynamic range, especially in low-supply applications. Figure 1 shows the input and output waveforms for the OPA343 in unity-gain configuration. Operation is from a single +5V supply with a 10k load connected to VS /2. The input is a 5Vp-p sinusoid. Output voltage is approximately 4.98Vp-p. Power-supply pins should be bypassed with 0.01F ceramic capacitors. VS = +5, G = +1, RL = 10k 5 2V/div VIN 5 VOUT RAIL-TO-RAIL INPUT The input common-mode voltage range of the OPA343 series extends 500mV beyond the supply rails. This is achieved with a complementary input stage--an N-channel input differential pair in parallel with a P-channel differential pair, as shown in Figure 2. The N-channel pair is active for input voltages close to the positive rail, typically (V+) - 1.3V to 500mV above the positive supply. The P-channel pair is on for inputs from 500mV below the negative supply to approximately (V+) - 1.3V. There is a small transition region, typically (V+) - 1.5V to (V+) - 1.1V, in which both input pairs are on. This 400mV transition region can vary 300mV with process variation. Thus, the transition region (both stages on) can range from (V+) - 1.8V to (V+) - 1.4V on the low end, up to (V+) - 1.2V to (V+) - 0.8V on the high end. Within the 400mV transition region PSRR, CMRR, offset voltage, offset drift, and THD may be degraded compared to operation outside this region. A double-folded cascode adds the signal from the two input pairs and presents a differential signal to the class AB output stage. Normally, input bias current is approximately 200fA, however, input voltages exceeding the power supplies by 0 FIGURE 1. Rail-to-Rail Input and Output. V+ Reference Current VIN+ VIN- VBIAS1 Class AB Control Circuitry VO VBIAS2 V- (Ground) FIGURE 2. Simplified Schematic. 8 OPA343, 2343, 4343 SBOS090A more than 500mV can cause excessive current to flow in or out of the input pins. Momentary voltages greater than 500mV beyond the power supply can be tolerated if the current on the input pins is limited to 10mA. This is easily accomplished with an input resistor, as shown in Figure 3. Many input signals are inherently current-limited to less than 10mA, therefore, a limiting resistor is not required. V+ IOVERLOAD 10mA max VOUT OPAx343 VIN 5k FIGURE 3. Input Current Protection for Voltages Exceeding the Supply Voltage. RAIL-TO-RAIL OUTPUT A class AB output stage with common-source transistors is used to achieve rail-to-rail output. For light resistive loads (>50k), the output voltage is typically a few millivolts from the supply rails. With moderate resistive loads (2k to 50k), the output can swing to within a few tens of millivolts from the supply rails and maintain high open-loop gain. See the typical performanc curve "Output Voltage Swing vs Output Current." CAPACITIVE LOAD AND STABILITY OPA343 series op amps can drive a wide range of capacitive loads. However, all op amps under certain conditions may become unstable. Op amp configuration, gain, and load value are just a few of the factors to consider when determining stability. An op amp in unity gain configuration is the most susceptible to the effects of capacitive load. The capacitive load reacts with the op amp's output resistance, along with any additional load resistance, to create a pole in the small-signal response which degrades the phase margin. In unity gain, OPA343 series op amps perform well, with a pure capacitive load up to approximately 1000pF. Increasing gain enhances the amplifier's ability to drive more capacitance. See the typical performance curve "Small-Signal Overshoot vs Capacitive Load." One method of improving capacitive load drive in the unity gain configuration is to insert a 10 to 20 resistor in series with the output, as shown in Figure 4. This significantly reduces ringing with large capacitive loads. However, if there is a resistive load in parallel with the capacitive load, RS creates a voltage divider. This introduces a dc error at the output and slightly reduces output swing. This error may be insignificant. For instance, with RL = 10k and RS = 20, there is only about a 0.2% error at the output. DRIVING A/D CONVERTERS OPA343 series op amps are optimized for driving medium speed (up to 100kHz) sampling A/D converters. However, they also offer excellent performance for higher-speed converters. The OPA343 series provides an effective means of buffering the A/D's input capacitance and resulting charge injection while providing signal gain. For applications requiring high accuracy, the OPA340 series is recommended. Figures 5 and 6 show the OPA343 driving an ADS7816. The ADS7816 is a 12-bit, micro-power sampling converter in the tiny MSOP-8 package. When used with the miniature package options of the OPA343 series, the combination is ideal for space-limited and low-power applications. For further information consult the ADS7816 data sheet. With the OPA343 in a noninverting configuration, an RC network at the amplifier's output can be used to filter high frequency noise in the signal (see Figure 5). In the inverting configuration, filtering may be accomplished with a capacitor across the feedback resistor (see Figure 6). V+ RS VOUT OPAx343 VIN 10 to 20 RL CL FIGURE 4. Series Resistor in Unity-Gain Configuration Improves Capacitive Load Drive. OPA343, 2343, 4343 SBOS090A 9 +5V For improved accuracy use OPA340. 0.1F 0.1F 1 VREF 8 V+ 7 DCLOCK 500 +In OPA343 ADS7816 12-Bit A/D 2 VIN -In Serial Interface 5 CS/SHDN 3 3300pF 6 DOUT GND 4 VIN = 0V to 5V for 0V to 5V output. NOTE: A/D Input = 0 to VREF RC network filters high frequency noise. FIGURE 5. OPA343 in Noninverting Configuration Driving ADS7816. +5V 330pF 0.1F For improved accuracy use OPA340. 5k 0.1F 5k VIN 1 VREF 8 V+ DCLOCK +In OPA343 ADS7816 12-Bit A/D 2 DOUT -In CS/SHDN 3 7 6 Serial Interface 5 GND 4 VIN = 0V to -5V for 0V to 5V output. NOTE: A/D Input = 0 to VREF FIGURE 6. OPA343 in Inverting Configuration Driving ADS7816. Filters 160Hz to 2.4kHz +5V 10M VIN 200pF 10M 1/2 OPA2343 243k 1.74M 47pF 1/2 OPA2343 RL 220pF FIGURE 7. Speech Bandpass Filter. <1pF (prevents gain peaking) 10M +V OPA343 VO FIGURE 8. Transimpedance Amplifier. 10 OPA343, 2343, 4343 SBOS090A PACKAGE OPTION ADDENDUM www.ti.com 16-Aug-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) OPA2343EA/250 ACTIVE VSSOP DGK 8 250 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR OPA2343EA/250G4 ACTIVE VSSOP DGK 8 250 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR OPA2343EA/2K5 ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR OPA2343EA/2K5G4 ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR OPA2343UA ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA2343UA/2K5 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA2343UA/2K5G4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA2343UAG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA343NA/250 ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM OPA343NA/250G4 ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM OPA343NA/3K ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM OPA343NA/3KG4 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM OPA343UA ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA343UA/2K5 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA343UA/2K5G4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA343UAG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA4343EA/250 ACTIVE SSOP DBQ 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Addendum-Page 1 Samples (Requires Login) PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 16-Aug-2012 Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) OPA4343EA/250G4 ACTIVE SSOP DBQ 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA4343EA/2K5 ACTIVE SSOP DBQ 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA4343EA/2K5G4 ACTIVE SSOP DBQ 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA4343NA/250 ACTIVE TSSOP PW 14 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA4343NA/250G4 ACTIVE TSSOP PW 14 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA4343NA/2K5 ACTIVE TSSOP PW 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA4343NA/2K5G4 ACTIVE TSSOP PW 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA4343UA ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA4343UA/2K5 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM OPA4343UA/2K5G4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM OPA4343UAG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Samples (Requires Login) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Addendum-Page 2 PACKAGE OPTION ADDENDUM www.ti.com 16-Aug-2012 Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 16-Aug-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant OPA2343EA/250 VSSOP DGK 8 250 180.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 OPA2343EA/2K5 VSSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 OPA2343UA/2K5 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 OPA343NA/250 SOT-23 DBV 5 250 178.0 9.0 3.23 3.17 1.37 4.0 8.0 Q3 OPA343NA/3K SOT-23 DBV 5 3000 178.0 9.0 3.23 3.17 1.37 4.0 8.0 Q3 OPA343UA/2K5 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 OPA4343EA/250 SSOP DBQ 16 250 180.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 OPA4343EA/2K5 SSOP DBQ 16 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 OPA4343NA/250 TSSOP PW 14 250 180.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 OPA4343NA/2K5 TSSOP PW 14 2500 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 OPA4343UA/2K5 SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 16-Aug-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) OPA2343EA/250 VSSOP DGK OPA2343EA/2K5 VSSOP DGK 8 250 210.0 185.0 35.0 8 2500 367.0 367.0 35.0 OPA2343UA/2K5 SOIC D 8 2500 367.0 367.0 35.0 OPA343NA/250 SOT-23 DBV 5 250 180.0 180.0 18.0 OPA343NA/3K SOT-23 DBV 5 3000 180.0 180.0 18.0 OPA343UA/2K5 SOIC D 8 2500 367.0 367.0 35.0 OPA4343EA/250 SSOP DBQ 16 250 210.0 185.0 35.0 OPA4343EA/2K5 SSOP DBQ 16 2500 367.0 367.0 35.0 OPA4343NA/250 TSSOP PW 14 250 210.0 185.0 35.0 OPA4343NA/2K5 TSSOP PW 14 2500 367.0 367.0 35.0 OPA4343UA/2K5 SOIC D 14 2500 367.0 367.0 38.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated