Freescale Semiconductor Technical Data Document Number: MC33186 Rev. 7.0, 10/2011 H-Bridge Driver 33186 The 33186 is a monolithic H-Bridge ideal for fractional horsepower DC-motor and bi-directional thrust solenoid control. The IC incorporates internal control logic, charge pump, gate drive, and low RDS(ON) MOSFET output circuitry. The 33186 is able to control continuous inductive DC load currents up to 5.0 A. Output loads can be pulse width modulated (PWM-ed) at frequencies up to 10 kHz. The 33186 is parametrically specified over a temperature range of -40C TA 125C, 5.0 V V+ 28 V. The IC can also be operated up to 40 V with de-rating of the specifications. The IC is available in a surface mount power package with exposed pad for heat sinking. H-BRIDGE MOTOR DRIVER Features * Overtemperature, Short-Circuit Protection, and Overvoltage Protection against Transients up to 40 V at VBAT Typical * RDSon = 150 m for each output Transistor at 25C * Continuous DC Load Current 5 A (TC < 100C) * Output Current Limitation at typ 6,5 A +/- 20% * Short-Circuit Shutdown for Output Currents over 8 A * Logic Inputs TTL/CMOS Compatible * Operating Frequency up to 20 kHz * Undervoltage Disable Function * Diagnostic Output, 2 Disable Input * Coding Input for Alternative Functions * Stable Operation with an External Capacitance of Maximum 47 F at VBAT * Pb-Free Packaging Designated by Suffix Code VW ORDERING INFORMATION Device CP SF IN1 IN2 DI1 DI2 MC33186VW1/R2 VPWR VBAT OUT1 MOTOR OUT2 PGND Figure 1. 33186 Simplified Block Diagram *This document contains certain information on a product under development. Freescale reserves the right to change or discontinue this product without notice (c) Freescale Semiconductor, Inc., 2007 - 2011. All rights reserved. Temperature Range (TA) Package - 40C to 125C 20 HSOP MC33186DH1/R2 33186 5.0 V MCU or DSP DH SUFFIX VW SUFFIX (PB-FREE) PLASTIC PACKAGE 98ASH70702A 20-PIN HSOP INTERNAL BLOCK DIAGRAM INTERNAL BLOCK DIAGRAM CP VBAT VBAT VBAT Internal 5V Charge-Pump Undervoltage SF Overcurrent High-Side Gate Control: 1-2 IN1 OUT1 IN2 Logic Gate Control: 3-4 DI1 DI2 Overtemperature COD Current limitation OUT2 Overcurrent Current Limit Low-Side PGND Figure 2. 33186 Simplified Internal Block Diagram 33186 2 Analog Integrated Circuit Device Data Freescale Semiconductor PIN CONNECTIONS PIN CONNECTIONS PIN CONNECTIONS AGND 1 20 NC SF 2 19 IN2 IN1 3 18 DI1 VBAT 4 17 CP VBAT 5 16 VBAT OUT1 6 15 OUT2 OUT1 7 14 OUT2 COD 8 13 DI2 PGND 9 12 PGND PGND 10 11 PGND Metal slug is connected to power ground (Top View) Figure 3. 33186 Pin Locations Table 1. 33186 Pin Description Pin Name 9, 10, 11, 12 PGND Power Ground. All the ground are connected together, they should be connected as short as possible on the PCB. 1 AGND Analog ground. All the ground are connected together, they should be connected as short as possible on the PCB. 2 Output Open drain output, active low. Is set according to the truth table. When a fault appears, SF changes typically in less than 100 ms. Metal slug Status flag (SF) 3,13 Inputs IN1, IN2, 18, 19 DI1, DI2, COD 8 COD Description Voltage controlled inputs with hysteresis When not connected or connected to GND, a stored failure will be reset by change of the voltagelevel on DI1 or DI2. When connected to VCC, the disable Pin DI1 and DI2 are inactive. A stored failure will be reset by change of the voltage-level on IN1 or IN2. 6, 7, 14, 15 OUT1, OUT2 H-Bridge outputs with integrated free-wheeling diodes. 33186 Analog Integrated Circuit Device Data Freescale Semiconductor 3 PIN CONNECTIONS Table 1. 33186 Pin Description(continued) Pin Name Description 4, 5, 16 VBAT The Pins 4 and 5 are internally connected. These Pins supply the left high side and the analog/logic part of the device. The Pin 16 supplies the right high side and the charge pump. The Pins 4, 5 and 16 should be connected together on the printed circuit board with connections as short as possible. Supervision and protection functions a) Supply voltage supervision The supply voltage is supervised. If it is below its specific threshold, the power stages are switched in tristate and the status flag is switched low. If the supply voltage is over the specific threshold again, the power stage switches independently into normal operation, according to the input Pins and the status flag is reset. b) Thermal supervision In case of overtemperature, the power stages are switched in tristate independent of the inputs signals and the status flag is switched low. If the level changes from high to low on DI1 (IN1) or low to high on DI2 (IN2), the output stage switches on again if the temperature is below the specified limit.The status-flag is reset to high level (Pin names in brackets refer to coding Pin = VCC). c) Supervision of overcurrent on high sides and low sides In case of over-current detection, the power stages are switched in tristate independent of the inputs signals and the status flag is set. If the level changes from high to low on DI1 (IN1) or low to high on DI2 (IN2) the output stage switches on again and the status flag is reset to high level (Pin names in brackets refer to coding Pin = VCC). The output stage switches into the mode defined by the inputs Pins provided, and/if the temperature is below the specified limits. d) Current limiting on low sides The maximum current which can flow under normal operating conditions is limited to Imax = 6,5 A +/- 20%. When the maximum current value is reached, the output stages are switched tristate for a fixed time. According to the time constant the current decreases until the next switch on occurs. See page 8 for schematics. 17 CP Charge Pump output Pin A filtering capacitor (up to 33 nF) can be connected between Pin 17 and Gnd. Device can operate without external capacitor, although Pin 17 decoupling capacitor help in noise reduction and allows the device to perform a maximum speed, timing and PWM frequency. 33186 4 Analog Integrated Circuit Device Data Freescale Semiconductor ELECTRICAL CHARACTERISTICS MAXIMUM RATINGS ELECTRICAL CHARACTERISTICS MAXIMUM RATINGS Table 2. MAXIMUM RATINGS All voltages are with respect to ground unless otherwise noted. Exceeding these ratings may cause a malfunction or permanent damage to the device. Ratings Symbol Min Typ Max Unit Static Destruction Proof VBAT - 1.0 - 28 Dynamic Destruction Proof t < 0,5 s VBat - 2.0 - 40 U - 0.5 - 7.0 V USF - 0.5 - 7.0 V Junction Temperature TJ - 40 - +150 C Storage Temperature TS - 55 - +125 C Ambient Temperature TA - 40 - +125 C RthJC - - +1.5 K/W RthJC - - +1.5 K/W ELECTRICAL RATINGS Supply Voltage Logic Inputs (IN1, IN2, DI1, DI2, CODE) Output Status - Flag SF V THERMAL RATINGS Thermal Resistance (with power applied on 2 power MOS) Thermal Resistance (with power applied on 2 power MOS) Peak Package Reflow Temperature During Reflow (1), (2) TPPRT Note 2. C Notes 1. Pin soldering temperature limit is for 10 seconds maximum duration. Not designed for immersion soldering. Exceeding these limits may cause malfunction or permanent damage to the device. 2. Freescale's Package Reflow capability meets Pb-free requirements for JEDEC standard J-STD-020C. For Peak Package Reflow Temperature and Moisture Sensitivity Levels (MSL), Go to www.freescale.com, search by part number [e.g. remove prefixes/suffixes and enter the core ID to view all orderable parts. (i.e. MC33xxxD enter 33xxx), and review parametrics. 33186 Analog Integrated Circuit Device Data Freescale Semiconductor 5 ELECTRICAL CHARACTERISTICS STATIC ELECTRICAL CHARACTERISTICS STATIC ELECTRICAL CHARACTERISTICS Table 3. STATIC ELECTRICAL CHARACTERISTICS Characteristic noted under conditions -40C to +125 C, VBAT from 5 V to 28 V, unless otherwise note. Typical values reflect approximate mean at 25C, nominal VCC, at time of device characterization. Characteristics Symbol Min Typ Max Unit Static VBAT - - V VBAT 5.0 - 28 Dynamic (t < 500 ms) 40 V - - 35 mA V POWER SUPPLY Operating Range: Stand-by current f = 0 to 10 KHz; IOUT = 0 A I VBAT VBAT-undervoltage switch-off (without load) Switch-off Voltage 4.15 4.4 4.65 Switch-on Voltage 4.5 4.75 5.0 V Hysteresis 150 - - mV 3.35 - - - - V 20 V CHARGE-PUMP SUPPLY VBAT = 4.15 V VCP - VBAT VBAT < 40 V VCP - VBAT LOGIC INPUTS Input High VINH 3.4 - - V Input Low VINL - - 1.4 V Input Hysteresis U 0.7 1.0 - V Input Pull Up Current (IN1, IN2, DI1) I - 200 - 80 - A IDI2 - 25 100 A - - 300 m UIN = 0.0 V Input Pull Down Current (DI2,COD)(3) UDI2 = 5.0 V POWER OUTPUTS: OUT1, OUT2 Switch on resistance: ROUT - VBAT; ROUT - GND VBAT = 5 to 28 V; CCP = 0 to 33 nF Switch-off Current during Current Limitation on Low Sides (IOUT) MAX 5.2 6.5 7.8 A Switch-off Time during Current Limitation on Low Sides tA 15 20.5 26 s Blanking Time during Current Limitation on Low Sides tB 12 16.5 21 s Notes 3. In case of negative voltage at OUT2 (respectively OUT1) this maximum pull down current at DI2 (respectively COD) Pin can be exceeded. This happens during recirculation when the current is flowing in the low side. See curve 22. 33186 6 Analog Integrated Circuit Device Data Freescale Semiconductor ELECTRICAL CHARACTERISTICS STATIC ELECTRICAL CHARACTERISTICS Table 3. STATIC ELECTRICAL CHARACTERISTICS(continued) Characteristic noted under conditions -40C to +125 C, VBAT from 5 V to 28 V, unless otherwise note. Typical values reflect approximate mean at 25C, nominal VCC, at time of device characterization. Characteristics Symbol Min Typ Max Unit IOCHS 11 - - A IOCLS 8.0 - - - - 100 A UD - - 2.0 V tRR - 2.0 5.0 s Switch-off Temperature 160 - 190 C Hysteresis 20 - 30 C ISF - - 10 A VSF - - 1.0 V f - - 10 KHz f - - 20 KHz tDON - - 15 s tDOFF - - 15 s tr, tf 2.0 - 5.0 s tDDIS High Side Overcurrent Detection (4) Low Side Overcurrent Detection Leakage Current Output Stage Switched off Free-Wheeling Diode Forward Voltage IOU = 3.0 A Free-Wheeling Diode Reverse Recovery Time IFM =1.0 A, di/dt = 4.0 A/s OUTPUT STATUS FLAG (OPEN DRAIN OUTPUT) Output High (SF not set) USF = 5.0 V Output Low (SF set) ISF = 300 A TIMING PWM frequency CCP = 33 nF Maximum Switching Frequency During Current Limitation VBAT = 6....28 V.....CCP = 33 nF Output ON Delay IN1.....>OUT1 or IN2.....>OUT2 Output OFF Delay IN1.....>OUT1 or IN2.....>OUT2 Output Switching Time CCP = 0 to 33 nF OUTiH.....OUTiL, OUTiL.....OUTiH, IOUT = 3.0 A Disable Delay Time - - 8.0 s Turn off in Case of Overcurrent or Overtemperature - 4.0 8.0 s Power On Delay Time (CCP = 33 nF)(5) - 1.0 5.0 ms DIi.....OUTi Notes 4. In case of overcurrent, the time when the current is greater than 7.8 A is lower than 30 s, with a maximum frequency of 1 kHz. 5. This parameter corresponds to the time for CCP to reach its nominal value when VBAT is applied. 33186 Analog Integrated Circuit Device Data Freescale Semiconductor 7 ELECTRICAL CHARACTERISTICS TRUTH TABLE TRUTH TABLE Table 4. TRUTH TABLE Device State Input Conditions Status Outputs DI1 (8) DI2 (8) IN1 IN2 SF(9) SF(10) OU1 OU2 1-Forward L H H L H H H L 2-Reverse L H L H H H L H 3-Free Wheeling Low L H L L H H L L 4-Free Wheeling High L H H H H H H H 5-Disable 1 H X X X L H Z Z 6-Disable 2 X L X X L H Z Z 7-IN1 Disconnected L H Z X H H H X 8-IN2 Disconnected L H X Z H H X H 9-DI1 Disconnected Z X X X L H Z Z 10-DI2 Disconnected X Z X X L H Z Z 11-Current Limit.active L H X X H H Z Z 12-Undervoltage(6) X X X X L L Z Z 13-Overtemperature(7) X X X X L L Z Z 14-Overcurrent(7) X X X X L L Z Z Notes 6. In case of undervoltage, tristate and status-flag are reset automatically. 7. Whenever overcurrent or overtemperature is detected, the fault is stored (i.e.status-flag remains low). The tristate conditions and the status-flag are reset via DI1 (IN1) or DI2 (IN2). Pin names in brackets refer to coding Pin (COD = VCC). 8. If COD = VCC then DI1 and DI2 are not active. 9. COD = nc or GND 10. COD = VCC L = Low H = High X = High or Low Z = High impedance (all output stage transistors are switched off). 33186 8 Analog Integrated Circuit Device Data Freescale Semiconductor ELECTRICAL CHARACTERISTICS 10k 47F Ccp=33nF VBAT Voltage VCC Regulator Power Ground SF CP VBAT Micro controller IN1 IN2 OUT1 M DI1 OUT2 DI2 COD GND Power Ground Figure 4. Typical Application INn 50% 50% tDON OUn tDOFF 90% 10% Figure 5. Output Delay Time 33186 Analog Integrated Circuit Device Data Freescale Semiconductor 9 ELECTRICAL CHARACTERISTICS DIn 50% tDDIS OUn 10% Z Figure 6. Disable Delay Time 90% 90% OUn 10% tf 10% tr Figure 7. Output Switching Time 33186 10 Analog Integrated Circuit Device Data Freescale Semiconductor ELECTRICAL CHARACTERISTICS Loadcurrent Overturned > 8A TYP 6.5A A Control signal Status Flag Overcurrent detection Detail A tA 6.5A tB tA = switch-off time in current limitation tB = current limitation blanking time Figure 8. Current Limitation on Low Side 33186 Analog Integrated Circuit Device Data Freescale Semiconductor 11 ELECTRICAL CHARACTERISTICS 2,83 13 2,82 12,5 2,81 12 2,80 VinH (V) IVBAT (mA) 13,5 11,5 11 10,5 VBAT=12V 2,76 9,5 -25 0 25 50 75 T, TEMPERATURE (C) 100 2,75 -50 125 Figure 9. Stand-by Current vs. Temperature Switch on Voltage Vcp (V) VBAT(V) 30 4,50 Switch off Voltage 25 20 15 4,30 10 -25 0 25 50 75 T, TEMPERATURE (C) 100 5 125 0 5 0 Figure 10. VBAT Undervoltage vs. Temperature 10 15 20 25 BATTERY VOLTAGE (V) 30 35 Figure 13. Vcp vs. Battery Voltage 1,89 1,88 200 1,87 190 1,86 180 1,85 170 RDSon (m) VinL (V) 125 without Ccp 35 4,60 1,84 1,83 1,82 1,81 -50 100 Tambient=25C 40 4,70 4,20 -50 0 25 50 75 T, TEMPERATURE (C) 45 4,90 4,40 -25 Figure 12. High Threshold Input Voltage vs. Temperature 5,00 4,80 2,78 2,77 10 9 -50 2,79 VBAT=5V without Ccp 160 150 140 130 -25 0 25 50 75 T, TEMPERATURE (C) 100 125 120 110 -50 -25 0 25 50 75 100 125 T, TEMPERATURE (C) Figure 11. Low Threshold Input Voltage vs. Temperature Figure 14. RDSON vs. Temperature 33186 12 Analog Integrated Circuit Device Data Freescale Semiconductor ELECTRICAL CHARACTERISTICS ta=20.5s 7,20 7,10 Imotor (1A/div) IOUT max (A) 7,00 6,90 Out1 (5V/div) 6,80 6,70 6,60 6,50 Out2 (5V/div) 6,40 6,30 -50 -25 0 25 50 75 100 125 T, TEMPERATURE (C) Figure 18. Switch off Time Figure 15. Switch off Current vs. Temperature 17,50 17,00 IOCHS (A) 16,50 16,00 High side switch Out1 (5V/div) 15,50 15,00 14,50 14,00 13,50 13,00 -50 -25 0 25 50 75 100 125 tr=3.7s T, TEMPERATURE (C) Figure 16. Overcurrent Detection vs. Temperature Figure 19. Output Switching Time: Tr I(out) max= 7A Out1 (5V/div) Imotor (1A/div) tf=2.6s Figure 17. Current Limitation Figure 20. Output Switching Time: Tf 33186 Analog Integrated Circuit Device Data Freescale Semiconductor 13 ELECTRICAL CHARACTERISTICS in1 (1V/div) I(5A/div) Out1 (2V/div) Iochs= 16A tdoff=12.5s Figure 21. Output OFF Delay Figure 24. High Side Overcurrent High Side Detection 3.2 3 2.8 2.6 tdon=5.8s 2.4 2.2 2 Out1 (2V/div) 1.8 1.6 1.4 1.2 in1 (1V/div) 1 0.8 0.6 0.4 0.2 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 I OUT2 (A) Figure 22. Output ON Delay Note: Current through internal recirculation diode, @125C in case of negative voltage at OUT2 di2 (1V/div) Figure 25. Maximum Di2 Input Current vs. Iout2, current Out1 (2V/div) tdiss=0.9s Figure 23. Disable Delay Time 33186 14 Analog Integrated Circuit Device Data Freescale Semiconductor PACKAGING SOLDERING PACKAGING SOLDERING The 20 HSOP package is designed for enhanced thermal performance. The particularity of this package is its copper base plate on which the power die is soldered. The base plate is soldered on a PCB to provide heat flow to the ambient and also to provide a large thermal capacitance. Of course, the more copper area on the PCB, the better the power dissipation and transient behavior. We characterized the 20 HSOP on a double side PCB. The bottom side area of the copper is 7.8 cm2. The top surface is 2.7 cm2, see Figure 26. 100 10 Rth (C/W) 1 0,1 0,001 0,01 0,1 1 10 t, Time (s) 100 1000 10000 Figure 27. PHSOP20 Thermal Response Figure 27 shows the thermal response with the device soldered on to the test PCB described on Figure 26. Top Side Bottom Side Figure 26. PCB Test Layout 33186 Analog Integrated Circuit Device Data Freescale Semiconductor 15 PACKAGING PACKAGE DIMENSIONS PACKAGE DIMENSIONS Important: Package dimensions are provided in package drawings. To find the most current package outline drawing, go to www.freescale.com and perform a keyword search for the drawing's document number. Table 5. Package Drawing Information Package Suffix Package Outline Drawing Number 20-PIN HSOP DH/VW 98ASH70702A Dimensions shown are provided for reference ONLY (For Layout and Design, refer to the Package Outline Drawing listed in the following figures). 33186 16 Analog Integrated Circuit Device Data Freescale Semiconductor PACKAGING PACKAGE DIMENSIONS VW (Pb-FREE) SUFFIX 20-PIN HSOP 98ASH70702A ISSUE C 33186 Analog Integrated Circuit Device Data Freescale Semiconductor 17 PACKAGING PACKAGE DIMENSIONS VW (Pb-FREE) SUFFIX 20-PIN HSOP 98ASH70702A ISSUE C 33186 18 Analog Integrated Circuit Device Data Freescale Semiconductor PACKAGING PACKAGE DIMENSIONS VW (Pb-FREE) SUFFIX 20-PIN HSOP 98ASH70702A ISSUE C 33186 Analog Integrated Circuit Device Data Freescale Semiconductor 19 ADDITIONAL DOCUMENTATION THERMAL ADDENDUM (REV 2.0) ADDITIONAL DOCUMENTATION 33186DH 33186VW THERMAL ADDENDUM (REV 2.0) Introduction 20-PIN HSOP-EP This thermal addendum is provided as a supplement to the MC33186 technical datasheet. The addendum provides thermal performance information that may be critical in the design and development of system applications. All electrical, application, and packaging information is provided in the datasheet. Package and Thermal Considerations The MC33186 is offered in a 20 pin HSOP exposed pad, single die package. There is a single heat source (P), a single junction temperature (TJ), and thermal resistance (RJA). DH SUFFIX VW SUFFIX (Pb-FREE) 98ASH70273A 20-PIN HSOP-EP Note For package dimensions, refer to the 33186 data sheet. TJ = RJA . P The stated values are solely for a thermal performance comparison of one package to another in a standardized environment. This methodology is not meant to and will not predict the performance of a package in an applicationspecific environment. Stated values were obtained by measurement and simulation according to the standards listed below. Standards Table 6. Thermal Performance Comparison Thermal Resistance [C/W] (1), (2) 29 RJB (2), (3) 9.0 RJA (1), (4) 69 RJC (5) 2.0 RJA 1.0 0.2 1.0 0.2 Notes: 1. Per JEDEC JESD51-2 at natural convection, still air condition. 2. 2s2p thermal test board per JEDEC JESD51-5 and JESD51-7. 3. Per JEDEC JESD51-8, with the board temperature on the center trace near the center lead. 4. Single layer thermal test board per JEDEC JESD51-3 and JESD51-5. 5. Thermal resistance between the die junction and the exposed pad surface; cold plate attached to the package bottom side, remaining surfaces insulated. * All measurements are in millimeters Soldermast openings 20 Pin HSOP-EP 1.6 mm Pitch 16.0 mm x 11.0 mm Body 12.3 mm x 7.1 mm Exposed Pad Thermal vias connected to top buried plane Figure 28. Thermal Land Pattern for Direct Thermal Attachment According to JESD51-5 33186 20 Analog Integrated Circuit Device Data Freescale Semiconductor ADDITIONAL DOCUMENTATION THERMAL ADDENDUM (REV 2.0) A AGND SF IN1 VBAT VBAT OUT1 OUT1 COD PGND PGND 20 19 18 17 16 15 14 13 12 11 1 2 3 4 5 6 7 8 9 10 NC IN2 DI1 CP VBAT OUT2 OUT2 DI2 PGND PGND 33186DH1 Pin Connections 20-Pin HSOP-EP 1.6 mm Pitch 16.0 mm x 11.0 mm Body 12.3 x 7.1 mm exposed pad Figure 29. Thermal Test Board Device on Thermal Test Board Material: Outline: Single layer printed circuit board FR4, 1.6 mm thickness Cu traces, 0.07 mm thickness 80 mm x 100 mm board area, including edge connector for thermal testing Area A: Cu heat-spreading areas on board surface Ambient Conditions: Natural convection, still air Table 7. Thermal Resistance Performance A [mm2] RJA [C/W] 0 70 300 49 600 47 RJA is the thermal resistance between die junction and ambient air. 33186 Analog Integrated Circuit Device Data Freescale Semiconductor 21 ADDITIONAL DOCUMENTATION THERMAL ADDENDUM (REV 2.0) Thermal Resistance [C/W] Thermal Resistance [C/W] 80 80 70 70 60 60 50 50 40 40 30 30 20 20 x 10 10 RJA [C/W] 00 00 300 300 Heat spreading area A [mm] Heat Spreading Area A [mm2] 600 600 Figure 30. Device on Thermal Test Board RJA Thermal Resistance [C/W] Thermal Resistance [C/W] 100 100 10 10 x 1 RJA [C/W] 0.1 0.1 1.00E-03 1.00E-03 1.00E-02 1.00E-02 1.00E-01 1.00E-01 1.00E+00 1.00E+01 1.00E+03 1.00E+04 1.00E+00 1.00E+01 1.00E+02 1.00E+02 1.00E+03 1.00E+04 Time [s] Time[s] Figure 31. Transient Thermal Resistance RJA 1 W Step Response, Device on Thermal Test Board Area A = 600 (mm2) 33186 22 Analog Integrated Circuit Device Data Freescale Semiconductor REVISION HISTORY REVISION HISTORY REVISION DATE DESCRIPTION OF CHANGES 5.0 5/2006 * * Implemented Revision History page Added Lead Free (Pb-Free) Part Number MC33186VW1 6.0 10/2006 * * Updated data sheet formal Removed Peak Package Reflow Temperature During Reflow (solder reflow) parameter from MAXIMUM RATINGS on page 5. Added note with instructions to obtain this information from www.freescale.com. 7.0 10/2011 * Updated Package Dimensions according to the latest Freescale package specification 98ASH70702A_C Updated to the current Freescale form and style. * 33186 Analog Integrated Circuit Device Data Freescale Semiconductor 23 How to Reach Us: Home Page: www.freescale.com Web Support: http://www.freescale.com/support USA/Europe or Locations Not Listed: Freescale Semiconductor, Inc. Technical Information Center, EL516 2100 East Elliot Road Tempe, Arizona 85284 1-800-521-6274 or +1-480-768-2130 www.freescale.com/support Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen, Germany +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) www.freescale.com/support Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku, Tokyo 153-0064 Japan 0120 191014 or +81 3 5437 9125 support.japan@freescale.com Asia/Pacific: Freescale Semiconductor China Ltd. Exchange Building 23F No. 118 Jianguo Road Chaoyang District Beijing 100022 China +86 10 5879 8000 support.asia@freescale.com For Literature Requests Only: Freescale Semiconductor Literature Distribution Center P.O. Box 5405 Denver, Colorado 80217 1-800-441-2447 or +1-303-675-2140 Fax: +1-303-675-2150 LDCForFreescaleSemiconductor@hibbertgroup.com Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further to products herein. Freescale Semiconductor makes no warranty, representation or regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters that may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals", be validated for each customer application by technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. Freescale and the Freescale logo are trademarks of Freescale Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. Qorivva, S12 MagniV, SMARTMOS and Xtrinsic are trademarks of Freescale Semiconductor, Inc. ARM is the registered trademark of ARM Limited. The Power Architecture and Power.org word marks and the Power and Power.org logos and related marks are trademarks and service marks licensed by Power.org. All other product or service names are the property of their respective owners. (c)2011 Freescale Semiconductor, Inc. MC33186 Rev. 7.0 10/2011