S29GL-P MirrorBit(R) Flash Family S29GL01GP, S29GL512P, S29GL256P, S29GL128P 1 Gigabit, 512 Megabit, 256 Megabit and 128 Megabit 3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology S29GL-P MirrorBit(R) Flash Family Cover Sheet Data Sheet (Preliminary) Notice to Readers: This document states the current technical specifications regarding the Spansion product(s) described herein. The Preliminary status of this document indicates that product qualification has been completed, and that initial production has begun. Due to the phases of the manufacturing process that require maintaining efficiency and quality, this document may be revised by subsequent versions or modifications due to changes in technical specifications. Publication Number S29GL-P_00 Revision A Amendment 7 Issue Date November 8, 2007 Data Sheet (Pre limin ar y) Notice On Data Sheet Designations Spansion Inc. issues data sheets with Advance Information or Preliminary designations to advise readers of product information or intended specifications throughout the product life cycle, including development, qualification, initial production, and full production. In all cases, however, readers are encouraged to verify that they have the latest information before finalizing their design. The following descriptions of Spansion data sheet designations are presented here to highlight their presence and definitions. Advance Information The Advance Information designation indicates that Spansion Inc. is developing one or more specific products, but has not committed any design to production. Information presented in a document with this designation is likely to change, and in some cases, development on the product may discontinue. Spansion Inc. therefore places the following conditions upon Advance Information content: "This document contains information on one or more products under development at Spansion Inc. The information is intended to help you evaluate this product. Do not design in this product without contacting the factory. Spansion Inc. reserves the right to change or discontinue work on this proposed product without notice." Preliminary The Preliminary designation indicates that the product development has progressed such that a commitment to production has taken place. This designation covers several aspects of the product life cycle, including product qualification, initial production, and the subsequent phases in the manufacturing process that occur before full production is achieved. Changes to the technical specifications presented in a Preliminary document should be expected while keeping these aspects of production under consideration. Spansion places the following conditions upon Preliminary content: "This document states the current technical specifications regarding the Spansion product(s) described herein. The Preliminary status of this document indicates that product qualification has been completed, and that initial production has begun. Due to the phases of the manufacturing process that require maintaining efficiency and quality, this document may be revised by subsequent versions or modifications due to changes in technical specifications." Combination Some data sheets contain a combination of products with different designations (Advance Information, Preliminary, or Full Production). This type of document distinguishes these products and their designations wherever necessary, typically on the first page, the ordering information page, and pages with the DC Characteristics table and the AC Erase and Program table (in the table notes). The disclaimer on the first page refers the reader to the notice on this page. Full Production (No Designation on Document) When a product has been in production for a period of time such that no changes or only nominal changes are expected, the Preliminary designation is removed from the data sheet. Nominal changes may include those affecting the number of ordering part numbers available, such as the addition or deletion of a speed option, temperature range, package type, or VIO range. Changes may also include those needed to clarify a description or to correct a typographical error or incorrect specification. Spansion Inc. applies the following conditions to documents in this category: "This document states the current technical specifications regarding the Spansion product(s) described herein. Spansion Inc. deems the products to have been in sufficient production volume such that subsequent versions of this document are not expected to change. However, typographical or specification corrections, or modifications to the valid combinations offered may occur." Questions regarding these document designations may be directed to your local sales office. 2 S29GL-P MirrorBit(R) Flash Family S29GL-P_00_A7 November 8, 2007 S29GL-P MirrorBit(R) Flash Family S29GL01GP, S29GL512P, S29GL256P, S29GL128P 1 Gigabit, 512 Megabit, 256 Megabit and 128 Megabit 3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology Data Sheet (Preliminary) General Description The Spansion S29GL01G/512/256/128P are Mirrorbit(R) Flash products fabricated on 90 nm process technology. These devices offer a fast page access time of 25 ns with a corresponding random access time as fast as 90 ns. They feature a Write Buffer that allows a maximum of 32 words/64 bytes to be programmed in one operation, resulting in faster effective programming time than standard programming algorithms. This makes these devices ideal for today's embedded applications that require higher density, better performance and lower power consumption. Distinctive Characteristics Single 3V read/program/erase (2.7-3.6 V) Offered Packages Enhanced VersatileI/OTM control - All input levels (address, control, and DQ input levels) and outputs are determined by voltage on VIO input. VIO range is 1.65 to VCC 90 nm MirrorBit process technology 8-word/16-byte page read buffer 32-word/64-byte write buffer reduces overall programming time for multiple-word updates Secured Silicon Sector region - 128-word/256-byte sector for permanent, secure identification through an 8-word/16-byte random Electronic Serial Number - Can be programmed and locked at the factory or by the customer Uniform 64Kword/128KByte Sector Architecture - - - - Suspend and Resume commands for Program and Erase operations Write operation status bits indicate program and erase operation completion Unlock Bypass Program command to reduce programming time Support for CFI (Common Flash Interface) Persistent and Password methods of Advanced Sector Protection WP#/ACC input S29GL01GP: One thousand twenty-four sectors S29GL512P: Five hundred twelve sectors S29GL256P: Two hundred fifty-six sectors S29GL128P: One hundred twenty-eight sectors - Accelerates programming time (when VHH is applied) for greater throughput during system production - Protects first or last sector regardless of sector protection settings Hardware reset input (RESET#) resets device 100,000 erase cycles per sector typical Ready/Busy# output (RY/BY#) detects program or erase cycle completion 20-year data retention typical Publication Number S29GL-P_00 - 56-pin TSOP - 64-ball Fortified BGA Revision A Amendment 7 Issue Date November 8, 2007 This document states the current technical specifications regarding the Spansion product(s) described herein. The Preliminary status of this document indicates that product qualification has been completed, and that initial production has begun. Due to the phases of the manufacturing process that require maintaining efficiency and quality, this document may be revised by subsequent versions or modifications due to changes in technical specifications. Data Sheet (Pre limin ar y) Performance Characteristics Maximum Read Access Times (ns) Density 128 & 256 Mb 512 Mb 1 Gb Voltage Range (1) Random Access Time (tACC) Regulated VCC 90 Full VCC 100/110 VersatileIO VIO 110 Page Access Time (tPACC) CE# Access Time (tCE) 25 100/110 OE# Access Time (tOE) 90 25 110 Regulated VCC 100 Full VCC 100 (2)/110 100 VersatileIO VIO 110 (2)/120 110 (2)/120 Regulated VCC 110 110 Full VCC 120 VersatileIO VIO 130 25 25 100 (2)/110 120 25 25 130 Notes 1. Access times are dependent on VCC and VIO operating ranges. See Ordering Information page for further details. Regulated VCC: VCC = 3.0-3.6 V. Full VCC: VCC = VIO = 2.7-3.6 V. VersatileIO VIO: VIO = 1.65-VCC, VCC = 3 V. 2. Contact a sales representative for availability. Current Consumption (typical values) Random Access Read (f = 5 MHz) 30 mA 8-Word Page Read (f = 10 MHz) 1 mA Program/Erase 50 mA Standby 1 A Program & Erase Times (typical values) Single Word Programming Effective Write Buffer Programming (VCC) Per Word 15 s Effective Write Buffer Programming (VHH) Per Word 13.5 s Sector Erase Time (64 Kword Sector) 4 60 s S29GL-P MirrorBit(R) Flash Family 0.5 s S29GL-P_00_A7 November 8, 2007 Da ta Shee t (Prelimi nar y) Table of Contents General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Distinctive Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Performance Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1. Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2. Input/Output Descriptions & Logic Symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3. Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 4. Physical Dimensions/Connection Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1 Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2 Special Handling Instructions for BGA Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3 LAA064--64 ball Fortified Ball Grid Array, 11 x 13 mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4 TS056--56-Pin Standard Thin Small Outline Package (TSOP) . . . . . . . . . . . . . . . . . . . . . . 12 12 12 14 16 5. Additional Resources. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.1 Application Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2 Specification Bulletins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.3 Hardware and Software Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.4 Contacting Spansion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 17 17 17 17 6. Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 6.1 Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 7. Device Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.1 Device Operation Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.2 Word/Byte Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.3 VersatileIOTM (VIO) Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.4 Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.5 Page Read Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.6 Autoselect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.7 Program/Erase Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.8 Write Operation Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.9 Writing Commands/Command Sequences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 19 20 20 20 20 21 24 36 40 8. Advanced Sector Protection/Unprotection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.1 Lock Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.2 Persistent Protection Bits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.3 Persistent Protection Bit Lock Bit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.4 Password Protection Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.5 Advanced Sector Protection Software Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.6 Hardware Data Protection Methods. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 43 43 45 45 48 48 9. Power Conservation Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.1 Standby Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.2 Automatic Sleep Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.3 Hardware RESET# Input Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.4 Output Disable (OE#). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 49 49 49 49 10. Secured Silicon Sector Flash Memory Region . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.1 Factory Locked Secured Silicon Sector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.2 Customer Lockable Secured Silicon Sector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.3 Secured Silicon Sector Entry/Exit Command Sequences . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 50 50 51 11. Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.1 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.2 Operating Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.3 Test Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.4 Key to Switching Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.5 Switching Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.6 DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.7 AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 52 53 53 54 54 55 56 November 8, 2007 S29GL-P_00_A7 S29GL-P MirrorBit(R) Flash Family 5 Data 6 Sheet (Pre limin ar y) 12. Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 12.1 Command Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 12.2 Common Flash Memory Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 13. Advance Information on S29GL-R 65 nm MirrorBit Hardware Reset (RESET#) and Power-up Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 14. Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 S29GL-P MirrorBit(R) Flash Family S29GL-P_00_A7 November 8, 2007 Da ta Shee t (Prelimi nar y) Figures Figure 3.1 Figure 4.1 Figure 4.2 Figure 4.3 Figure 4.4 Figure 7.1 Figure 7.2 Figure 7.3 Figure 7.4 Figure 8.1 Figure 8.2 Figure 8.3 Figure 11.1 Figure 11.2 Figure 11.3 Figure 11.4 Figure 11.5 Figure 11.6 Figure 11.7 Figure 11.8 Figure 11.9 Figure 11.10 Figure 11.11 Figure 11.12 Figure 11.13 Figure 11.14 Figure 11.15 Figure 13.1 Figure 13.2 S29GL-P Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 64-ball Fortified Ball Grid Array . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 LAA064--64ball Fortified Ball Grid Array (FBGA), 11 x 13 mm . . . . . . . . . . . . . . . . . . . . . . .14 56-pin Standard TSOP (Top View) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 56-Pin Thin Small Outline Package (TSOP), 14 x 20 mm . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Single Word Program. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Write Buffer Programming Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Sector Erase Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Write Operation Status Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 Advanced Sector Protection/Unprotection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 PPB Program Algorithm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 Lock Register Program Algorithm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 Maximum Negative Overshoot Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Maximum Positive Overshoot Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Test Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Input Waveforms and Measurement Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Read Operation Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Page Read Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57 Reset Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Power-up Sequence Timings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Program Operation Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61 Accelerated Program Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61 Chip/Sector Erase Operation Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62 Data# Polling Timings (During Embedded Algorithms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62 Toggle Bit Timings (During Embedded Algorithms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63 DQ2 vs. DQ6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Alternate CE# Controlled Write (Erase/Program) Operation Timings . . . . . . . . . . . . . . . . . . 65 Reset Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Power-On Reset Timings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 November 8, 2007 S29GL-P_00_A7 S29GL-P MirrorBit(R) Flash Family 7 Data Sheet (Pre limin ar y) Tables Table 2.1 Table 6.1 Table 6.2 Table 6.3 Table 6.4 Table 7.1 Table 7.2 Table 7.3 Table 7.4 Table 7.5 Table 7.6 Table 7.7 Table 7.8 Table 7.9 Table 7.10 Table 7.11 Table 7.12 Table 7.13 Table 7.14 Table 7.15 Table 7.16 Table 7.17 Table 7.18 Table 8.1 Table 8.2 Table 10.1 Table 10.2 Table 10.3 Table 10.4 Table 11.1 Table 11.2 Table 11.3 Table 11.4 Table 11.5 Table 11.6 Table 11.7 Table 11.8 Table 11.9 Table 12.1 Table 12.2 Table 12.3 Table 12.4 Table 12.5 Table 12.6 Table 12.7 Table 12.8 Table 13.1 Table 13.2 8 Input/Output Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 S29GL01GP Sector & Memory Address Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 S29GL512P Sector & Memory Address Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 S29GL256P Sector & Memory Address Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 S29GL128P Sector & Memory Address Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Device Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Autoselect Codes, (High Voltage Method) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Autoselect Addresses in System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Autoselect Entry in System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 Autoselect Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 Single Word/Byte Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 Write Buffer Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Sector Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Chip Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 Erase Suspend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 Erase Resume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 Program Suspend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 Program Resume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 Unlock Bypass Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 Unlock Bypass Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 Unlock Bypass Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 Write Operation Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 Lock Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 Sector Protection Schemes: DYB, PPB and PPB Lock Bit Combinations . . . . . . . . . . . . . . .48 Secured Silicon Sector Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 Secured Silicon Sector Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51 Secured Silicon Sector Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51 Secured Silicon Sector Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 Test Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54 S29GL-P DC Characteristics (CMOS Compatible) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 S29GL-P Read-Only Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 Hardware Reset (RESET#) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 Power-up Sequence Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 S29GL-P Erase and Program Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 S29GL-P Alternate CE# Controlled Erase and Program Operations . . . . . . . . . . . . . . . . . . .64 Erase And Programming Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 Package Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 S29GL-P Memory Array Command Definitions, x16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68 S29GL-P Sector Protection Command Definitions, x16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69 S29GL-P Memory Array Command Definitions, x8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 S29GL-P Sector Protection Command Definitions, x8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71 CFI Query Identification String . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72 System Interface String . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73 Device Geometry Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73 Primary Vendor-Specific Extended Query . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74 Hardware Reset (RESET#) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 Power-Up Sequence Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 S29GL-P MirrorBit(R) Flash Family S29GL-P_00_A7 November 8, 2007 Da ta 1. Shee t (Prelimi nar y) Ordering Information The ordering part number is formed by a valid combination of the following: S29GL01GP 12 F F I 01 0 PACKING TYPE 0 = Tray (standard; see (Note 4) 2 = 7" Tape and Reel 3 = 13" Tape and Reel MODEL NUMBER (VIO range, protection when WP# =VIL) 01 = VIO = VCC = 2.7 to 3.6 V, highest address sector protected 02 = VIO = VCC = 2.7 to 3.6 V, lowest address sector protected V1 = VIO = 1.65 to VCC, VCC = 2.7 to 3.6 V, highest address sector protected V2 = VIO = 1.65 to VCC, VCC = 2.7 to 3.6 V, lowest address sector protected R1 = VIO = VCC = 3.0 to 3.6 V, highest address sector protected R2 = VIO = VCC = 3.0 to 3.6 V, lowest address sector protected TEMPERATURE RANGE I = Industrial (-40C to +85C) PACKAGE MATERIALS SET A = Pb (Note 1) F = Pb-free PACKAGE TYPE T = 56-pin Thin Small Outline Package (TSOP) Standard Pinout(TSO56) F = 64-ball Fortified Ball Grid Array, 1.0 mm pitch package (LAA064) SPEED OPTION 90 = 90 ns 10 = 100 ns 11 = 110 ns 12 = 120 ns 13 = 130 ns DEVICE NUMBER/DESCRIPTION S29GL01GP, S29GL512P, S29GL256P, S29GL128P 3.0 Volt-only, 1024, 512, 256 and 128 Megabit Page-Mode Flash Memory, manufactured on 90 nm MirrorBit(R) process technology November 8, 2007 S29GL-P_00_A7 S29GL-P MirrorBit(R) Flash Family 9 Data Sheet (Pre limin ar y) Recommended Combinations Recommended Combinations list configurations planned to be supported in volume for this device. Consult your local sales office to confirm availability of specific recommended combinations and to check on newly released combinations. S29GL-P Valid Combinations Speed Package & Temperature 11 Model Number Packing Type R1, R2 TAI (1)(2) 12 TFI (2) 13 01, 02 0, 3 (4) V1, V2 S29GL01GP 11 R1, R2 FAI (1)(3) 12 FFI (3) 13 10 TAI (1)(2) TFI (2) 01, 02 11(1), 12 V1, V2 10 R1, R2 10 (1), 11 FAI (1)(3) FFI (3) 11(1), 12 01, 02 0, 3 (4) 0, 2, 3 (4) V1, V2 R1, R2 90 10, 11 S29GL256P, S29GL128P 0, 2, 3 (4) R1, R2 10 (1), 11 S29GL512P 01, 02 V1, V2 TAI (1)(2) TFI (2) 11 01, 02 0, 3 (4) V1, V2 R1, R2 90 10, 11 FAI (1)(3) FFI (3) 11 01, 02 0, 2, 3 (4) V1, V2 Notes 1. Contact a local sales representative for availability. 2. TSOP package marking omits packing type designator from ordering part number. 3. BGA package marking omits leading "S29" and packing type designator from ordering part number. 4. Type 0 is standard. Specify other options as required. 10 S29GL-P MirrorBit(R) Flash Family S29GL-P_00_A7 November 8, 2007 Da ta Shee t (Prelimi nar y) 2. Input/Output Descriptions & Logic Symbol Table 2.1 identifies the input and output package connections provided on the device. Table 2.1 Input/Output Descriptions Symbol Type Description A25-A0 Input DQ14-DQ0 I/O DQ15/A-1 I/O CE# Input Chip Enable. Address lines for GL01GP A24-A0 for GL512P A23-A0 for GL256P, A22-A0 for GL128P. Data input/output. DQ15: Data input/output in word mode. A-1: LSB address input in byte mode. OE# Input Output Enable. WE# Input Write Enable. VCC Supply Device Power Supply. VIO Supply Versatile IO Input. VSS Supply Ground. NC No Connect RY/BY# Output BYTE# Input Selects data bus width. At VIL, the device is in byte configuration and data I/O pins DQ0DQ7 are active and DQ15/A-1 becomes the LSB address input. At VIH, the device is in word configuration and data I/O pins DQ0-DQ15 are active. RESET# Input Hardware Reset. Low = device resets and returns to reading array data. WP#/ACC Input Write Protect/Acceleration Input. At VIL, disables program and erase functions in the outermost sectors. At VHH, accelerates programming; automatically places device in unlock bypass mode. Should be at VIH for all other conditions. WP# has an internal pullup; when unconnected, WP# is at VIH. RFU Reserved November 8, 2007 S29GL-P_00_A7 Not connected internally. Ready/Busy. Indicates whether an Embedded Algorithm is in progress or complete. At VIL, the device is actively erasing or programming. At High Z, the device is in ready. Reserved for future use. S29GL-P MirrorBit(R) Flash Family 11 Data Sheet (Pre limin ar y) 3. Block Diagram Figure 3.1 S29GL-P Block Diagram DQ15-DQ0 RY/BY# VCC Sector Switches VSS VIO Erase Voltage Generator Input/Output Buffers RESET# WE# WP#/ACC BYTE# State Control Command Register PGM Voltage Generator Chip Enable Output Enable Logic CE# OE# STB Y-Decoder Y-Gating X-Decoder Cell Matrix Timer AMax**-A0 (A-1) Address Latch STB VCC Detector Data Latch ** AMax GL01GP=A25, AMax GL512P = A24, AMax GL256P = A23, AMax GL128P = A22 4. Physical Dimensions/Connection Diagrams This section shows the I/O designations and package specifications for the S29GL-P family. 4.1 Related Documents The following documents contain information relating to the S29GL-P devices. Click on the title or go to www.spansion.com download the PDF file, or request a copy from your sales office. Considerations for X-ray Inspection of Surface-Mounted Flash Integrated Circuits 4.2 Special Handling Instructions for BGA Package Special handling is required for Flash Memory products in BGA packages. Flash memory devices in BGA packages may be damaged if exposed to ultrasonic cleaning methods. The package and/or data integrity may be compromised if the package body is exposed to temperatures above 150C for prolonged periods of time. 12 S29GL-P MirrorBit(R) Flash Family S29GL-P_00_A7 November 8, 2007 Da ta Shee t (Prelimi nar y) Figure 4.1 64-ball Fortified Ball Grid Array Top View, Balls Facing Down RFU on S29GL128P RFU on S29GL256P RFU on S29GL512P A8 B8 C8 D8 E8 F8 G8 H8 RFU A22 A23 VIO VSS A24 A25 RFU A7 B7 C7 D7 E7 F7 G7 H7 A13 A12 A14 A15 A16 BYTE# DQ15/A-1 VSS A6 B6 C6 D6 E6 F6 G6 H6 A9 A8 A10 A11 DQ7 DQ14 DQ13 DQ6 A5 B5 C5 D5 E5 F5 G5 H5 DQ4 WE# RESET# A21 A19 DQ5 DQ12 VCC A4 B4 C4 D4 E4 F4 G4 H4 A18 A20 DQ2 DQ10 DQ11 DQ3 RY/BY# WP#/ACC A3 B3 C3 D3 E3 F3 G3 H3 A7 A17 A6 A5 DQ0 DQ8 DQ9 DQ1 A2 B2 C2 D2 E2 F2 G2 H2 A3 A4 A2 A1 A0 CE# OE# VSS A1 B1 C1 D1 E1 F1 G1 H1 RFU RFU RFU RFU RFU VIO RFU RFU Do not connect to VIL or VSS Note RFU = No Connect (NC) November 8, 2007 S29GL-P_00_A7 S29GL-P MirrorBit(R) Flash Family 13 Data 4.3 Sheet (Pre limin ar y) LAA064--64 ball Fortified Ball Grid Array, 11 x 13 mm Figure 4.2 LAA064--64ball Fortified Ball Grid Array (FBGA), 11 x 13 mm 14 S29GL-P MirrorBit(R) Flash Family S29GL-P_00_A7 November 8, 2007 Da ta Shee t (Prelimi nar y) Figure 4.3 56-pin Standard TSOP (Top View) NC on S29GL128P NC on S29GL256P NC on S29GL512P A23 A22 A15 A14 A13 A12 A11 A10 A9 A8 A19 A20 WE# RESET# A21 WP#/ACC RY/BY# A18 A17 A7 A6 A5 A4 A3 A2 A1 RFU RFU 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 A24 A25 A16 BYTE# VSS DQ15/A-1 DQ7 DQ14 DQ6 DQ13 DQ5 DQ12 DQ4 VCC DQ11 DQ3 DQ10 DQ2 DQ9 DQ1 DQ8 DQ0 OE# VSS CE# A0 Do not connect to VIL or VSS RFU VIO Note RFU = No Connect (NC) November 8, 2007 S29GL-P_00_A7 S29GL-P MirrorBit(R) Flash Family 15 Data 4.4 Sheet (Pre limin ar y) TS056--56-Pin Standard Thin Small Outline Package (TSOP) Figure 4.4 56-Pin Thin Small Outline Package (TSOP), 14 x 20 mm PACKAGE JEDEC SYMBOL MO-142 (B) EC MIN. NOM. MAX. 1 CONTROLLING DIMENSIONS ARE IN MILLIMETERS (mm). (DIMENSIONING AND TOLERANCING CONFORMS TO ANSI Y14.5M-1982.) A --- --- 1.20 2 PIN 1 IDENTIFIER FOR STANDARD PIN OUT (DIE UP). A1 0.05 --- 0.15 3 A2 0.95 1.00 1.05 b1 0.17 0.20 0.23 TO BE DETERMINED AT THE SEATING PLANE -C- . THE SEATING PLANE IS DEFINED AS THE PLANE OF CONTACT THAT IS MADE WHEN THE PACKAGE LEADS ARE ALLOWED TO REST FREELY ON A FLAT HORIZONTAL SURFACE. b c1 0.17 0.10 0.22 --- 0.27 0.16 4 DIMENSIONS D1 AND E DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE MOLD PROTUSION IS 0.15 mm PER SIDE. 5 c 0.10 --- 0.21 DIMENSION b DOES NOT INCLUDE DAMBAR PROTUSION. ALLOWABLE DAMBAR PROTUSION SHALL BE 0.08 mm TOTAL IN EXCESS OF b DIMENSION AT MAX MATERIAL CONDITION. MINIMUM SPACE BETWEEN PROTRUSION AND AN ADJACENT LEAD TO BE 0.07 mm. 6 THESE DIMESIONS APPLY TO THE FLAT SECTION OF THE LEAD BETWEEN 0.10 mm AND 0.25 mm FROM THE LEAD TIP. 7 LEAD COPLANARITY SHALL BE WITHIN 0.10 mm AS MEASURED FROM THE SEATING PLANE. 8 DIMENSION "e" IS MEASURED AT THE CENTERLINE OF THE LEADS. D 19.80 20.00 20.20 D1 18.30 18.40 18.50 E 13.90 14.00 14.10 e L 0.50 BASIC 0.50 0.60 0.70 O 0 - 8 R 0.08 --- 0.20 N 16 NOTES: TS 56 56 3160\38.10A S29GL-P MirrorBit(R) Flash Family S29GL-P_00_A7 November 8, 2007 Da ta 5. Shee t (Prelimi nar y) Additional Resources Visit www.spansion.com to obtain the following related documents: 5.1 Application Notes The following is a list of application notes related to this product. All Spansion application notes are available at http://www.spansion.com/support/technical_documents/application_notes.html Using the Operation Status Bits in AMD Devices Understanding Page Mode Flash Memory Devices MirrorBit(R) Flash Memory Write Buffer Programming and Page Buffer Read Common Flash Interface Version 1.4 Vendor Specific Extensions MirrorBit(R) Flash Memory Write Buffer Programming and Page Buffer Read Taking Advantage of Page Mode Read on the MCF5407 Coldfire Migration to S29GL128N and S29GL256N based on 110nm MirrorBit(R) Technology Optimizing Program/Erase Times Practical Guide to Endurance and Data Retention Configuring FPGAs using Spansion S29GL-N Flash Connecting SpansionTM Flash Memory to a System Address Bus Connecting Unused Data Lines of MirrorBit(R) Flash Reset Voltage and Timing Requirements for MirrorBit(R) Flash Versatile IO: DQ and Enhanced 5.2 Specification Bulletins Contact your local sales office for details. 5.3 Hardware and Software Support Downloads and related information on Flash device support is available at www.spansion.com/support/index.html Spansion low-level drivers Enhanced Flash drivers Flash file system Downloads and related information on simulation modeling and CAD modeling support is available at http:// www.spansion.com/support/simulation_models.html VHDL and Verilog IBIS ORCAD An FAQ (Frequently Asked Questions) list is available at www.spansion.com/support/ses/index.html 5.4 Contacting Spansion Obtain the latest list of company locations and contact information on our web site at www.spansion.com/about/location.html November 8, 2007 S29GL-P_00_A7 S29GL-P MirrorBit(R) Flash Family 17 Data 6. Sheet (Pre limin ar y) Product Overview The S29GL-P family consists of 1 Gb, 512 Mb, 256 Mb and 128 Mb, 3.0-volt-only, page mode Flash devices optimized for today's embedded designs that demand a large storage array and rich functionality. These devices are manufactured using 90 nm MirrorBit technology. These products offer uniform 64 Kword (128 Kb) uniform sectors and feature VersatileIO control, allowing control and I/O signals to operate from 1.65 V to VCC. Additional features include: Single word programming or a 32-word buffer for an increased programming speed Program Suspend/Resume and Erase Suspend/Resume Advanced Sector Protection methods for protecting sectors as required 128 words/256 bytes of Secured Silicon area for storing customer and factory secured information. The Secured Silicon Sector is One Time Programmable. 6.1 Memory Map The S29GL-P devices consist of uniform 64 Kword (128 Kb) sectors organized as shown in Table 6.1- Table 6.4. Table 6.1 S29GL01GP Sector & Memory Address Map Uniform Sector Size 64 Kword/128 Kb Sector Count 1024 Sector Range Address Range (16-bit) Notes SA00 0000000h - 000FFFFh Sector Starting Address : : SA1023 3FF0000H - 3FFFFFFh Sector Ending Address Note This table has been condensed to show sector-related information for an entire device on a single page. Sectors and their address ranges that are not explicitly listed (such as SA001-SA1022) have sector starting and ending addresses that form the same pattern as all other sectors of that size. For example, all 128 Kb sectors have the pattern xxx0000h-xxxFFFFh. Table 6.2 S29GL512P Sector & Memory Address Map Uniform Sector Size 64 Kword/128 Kb Sector Count 512 Sector Range Address Range (16-bit) Notes SA00 0000000h - 000FFFFh Sector Starting Address : : SA511 1FF0000H - 1FFFFFFh Sector Ending Address Note This table has been condensed to show sector-related information for an entire device on a single page. Sectors and their address ranges that are not explicitly listed (such as SA001-SA510) have sector starting and ending addresses that the same pattern as all other sectors of that size. For example, all 128 Kb sectors have the pattern xxx0000h-xxxFFFFh. Table 6.3 S29GL256P Sector & Memory Address Map Uniform Sector Size 64 Kword/128 Kb Sector Count 256 Sector Range Address Range (16-bit) Notes SA00 0000000h - 000FFFFh Sector Starting Address : : SA255 0FF0000H - 0FFFFFFh Sector Ending Address Note This table has been condensed to show sector-related information for an entire device on a single page. Sectors and their address ranges that are not explicitly listed (such as SA001-SA254) have sector starting and ending addresses that form the same pattern as all other sectors of that size. For example, all 128 Kb sectors have the pattern xxx0000h-xxxFFFFh. 18 S29GL-P MirrorBit(R) Flash Family S29GL-P_00_A7 November 8, 2007 Da ta Shee t (Prelimi nar y) Table 6.4 S29GL128P Sector & Memory Address Map Uniform Sector Size Sector Count 64 Kword/128 Kb 128 Sector Range Address Range (16-bit) Notes SA00 0000000h - 000FFFFh Sector Starting Address : : SA127 07F0000 - 7FFFFF Sector Ending Address Note This table has been condensed to show sector-related information for an entire device on a single page. Sectors and their address ranges that are not explicitly listed (such as SA001-SA510) have sector starting and ending addresses that form the same pattern as all other sectors of that size. For example, all 128 Kb sectors have the pattern xxx0000h-xxxFFFFh. 7. Device Operations This section describes the read, program, erase, handshaking, and reset features of the Flash devices. Operations are initiated by writing specific commands or a sequence with specific address and data patterns into the command registers (see Table 12.1 through Table 12.4). The command register itself does not occupy any addressable memory location; rather, it is composed of latches that store the commands, along with the address and data information needed to execute the command. The contents of the register serve as input to the internal state machine and the state machine outputs dictate the function of the device. Writing incorrect address and data values or writing them in an improper sequence may place the device in an unknown state, in which case the system must pull the RESET# pin low or power cycle the device to return the device to the reading array data mode. 7.1 Device Operation Table The device must be setup appropriately for each operation. Table 7.1 describes the required state of each control pin for any particular operation. Table 7.1 Device Operations DQ8-DQ15 CE# OE# WE# RESET# WP#/ACC Addresses (Note 1) DQ0-DQ7 BYTE#= VIH Read L L H H X AIN DOUT DOUT Write (Program/Erase) L H L H (Note 2) AIN (Note 3) (Note 3) Accelerated Program L H L H VHH AIN (Note 3) (Note 3) Operation BYTE#= VIL DQ8-DQ14 = High-Z, DQ15 = A-1 VCC 0.3 V X X VCC 0.3 V H X High-Z High-Z High-Z Output Disable L H H H X X High-Z High-Z High-Z Reset X X X L X X High-Z High-Z High-Z Standby Legend L = Logic Low = VIL, H = Logic High = VIH, VHH = 11.5-12.5V, X = Don't Care, AIN = Address In, DIN = Data In, DOUT = Data Out Notes 1. Addresses are AMax:A0 in word mode; AMax:A-1 in byte mode. 2. If WP# = VIL, on the outermost sector remains protected. If WP# = VIH, the outermost sector is unprotected. WP# has an internal pull-up; when unconnected, WP# is at VIH. All sectors are unprotected when shipped from the factory (The Secured Silicon Sector can be factory protected depending on version ordered.) 3. DIN or DOUT as required by command sequence, data polling, or sector protect algorithm. November 8, 2007 S29GL-P_00_A7 S29GL-P MirrorBit(R) Flash Family 19 Data 7.2 Sheet (Pre limin ar y) Word/Byte Configuration The BYTE# pin controls whether the device data I/O pins operate in the byte or word configuration. If the BYTE# pin is set at logic `1', the device is in word configuration, DQ0-DQ15 are active and controlled by CE# and OE#. If the BYTE# pin is set at logic `0', the device is in byte configuration, and only data I/O pins DQ0-DQ7 are active and controlled by CE# and OE#. The data I/O pins DQ8-DQ14 are tri-stated, and the DQ15 pin is used as an input for the LSB (A-1) address function. 7.3 VersatileIOTM (VIO) Control The VersatileIOTM (VIO) control allows the host system to set the voltage levels that the device generates and tolerates on all inputs and outputs (address, control, and DQ signals). VIO range is 1.65 to VCC. See Ordering Information on page 9 for VIO options on this device. For example, a VIO of 1.65-3.6 volts allows for I/O at the 1.8 or 3 volt levels, driving and receiving signals to and from other 1.8 or 3 V devices on the same data bus. 7.4 Read All memories require access time to output array data. In a read operation, data is read from one memory location at a time. Addresses are presented to the device in random order, and the propagation delay through the device causes the data on its outputs to arrive with the address on its inputs. The device defaults to reading array data after device power-up or hardware reset. To read data from the memory array, the system must first assert a valid address on Amax-A0, while driving OE# and CE# to VIL. WE# must remain at VIH. All addresses are latched on the falling edge of CE#. Data will appear on DQ15DQ0 after address access time (tACC), which is equal to the delay from stable addresses to valid output data. The OE# signal must be driven to VIL. Data is output on DQ15-DQ0 pins after the access time (tOE) has elapsed from the falling edge of OE#, assuming the tACC access time has been meet. 7.5 Page Read Mode The device is capable of fast page mode read and is compatible with the page mode Mask ROM read operation. This mode provides faster read access speed for random locations within a page. The page size of the device is 8 words/16 bytes. The appropriate page is selected by the higher address bits A(max)-A3. Address bits A2-A0 in word mode (A2 to A-1 in byte mode) determine the specific word within a page. The microprocessor supplies the specific word location. The random or initial page access is equal to tACC or tCE and subsequent page read accesses (as long as the locations specified by the microprocessor falls within that page) is equivalent to tPACC. When CE# is deasserted and reasserted for a subsequent access, the access time is tACC or tCE. Fast page mode accesses are obtained by keeping the "read-page addresses" constant and changing the "intra-read page" addresses. 20 S29GL-P MirrorBit(R) Flash Family S29GL-P_00_A7 November 8, 2007 Da ta 7.6 Shee t (Prelimi nar y) Autoselect The Autoselect mode provides manufacturer ID, Device identification, and sector protection information, through identifier codes output from the internal register (separate from the memory array) on DQ7-DQ0. This mode is primarily intended for programming equipment to automatically match a device to be programmed with its corresponding programming algorithm (see Table 7.3). The Autoselect codes can also be accessed in-system. There are two methods to access autoselect codes. One uses the autoselect command, the other applies VID on address pin A9. When using programming equipment, the autoselect mode requires VID (11.5 V to 12.5 V) on address pin A9. Address pins must be as shown in Table 7.2. To access Autoselect mode without using high voltage on A9, the host system must issue the Autoselect command. The Autoselect command sequence may be written to an address within a sector that is either in the read or erase-suspend-read mode. The Autoselect command may not be written while the device is actively programming or erasing. The system must write the reset command to return to the read mode (or erase-suspend-read mode if the sector was previously in Erase Suspend). It is recommended that A9 apply VID after power-up sequence is completed. In addition, it is recommended that A9 apply from VID to VIH/VIL before power-down the VCC/VIO. See Table 12.1 on page 68 for command sequence details. When verifying sector protection, the sector address must appear on the appropriate highest order address bits (see Table 7.4 to Table 7.5). The remaining address bits are don't care. When all necessary bits have been set as required, the programming equipment may then read the corresponding identifier code on DQ15-DQ0. The Autoselect codes can also be accessed in-system through the command register. November 8, 2007 S29GL-P_00_A7 S29GL-P MirrorBit(R) Flash Family 21 Data Sheet (Pre limin ar y) Table 7.2 Autoselect Codes, (High Voltage Method) Description Device ID Device ID Device ID Device ID S29GL128P S29GL256P S29GL512P S29GL01GP Manufacturer ID: Spansion Product Amax A14 to to CE# OE# WE# A16 A10 L L H X X A9 A8 to A7 VID X DQ8 to DQ15 A6 A5 to A4 A3 to A2 A1 A0 L X L L L BYTE# BYTE# = VIL = VIH 00 DQ7 to DQ0 X 01h Cycle 1 L L H 22 X 7Eh Cycle 2 H H L 22 X 28h H H H 22 X 01h L L H X X VID X L X Cycle 3 Cycle 1 L L H 22 X 7Eh Cycle 2 H H L 22 X 23h Cycle 3 H H H 22 X 01h Cycle 1 L L H 22 X 7Eh H H L 22 X 22h H H H 22 X 01h Cycle 2 L L L L H H X X X X VID VID X X L L X X Cycle 3 Cycle 1 L L H 22 X 7Eh Cycle 2 H H L 22 X 21h H H H 22 X 01h L L H X X VID X L X Cycle 3 Sector Group Protection Verification L L H SA X VID X L X L H L X X 01h (protected), 00h (unprotected) Secured Silicon Sector Indicator Bit (DQ7), WP# protects highest address sector L L H X X VID X L X L H H X X 99h (factory locked), 19h (not factory locked) Secured Silicon Sector Indicator Bit (DQ7), WP# protects lowest address sector L L H X X VID X L X L H H X X 89h (factory locked), 09h (not factory locked) Legend L = Logic Low = VIL, H = Logic High = VIH, SA = Sector Address, X = Don't care. VID = 11.5V to 12.5V Table 7.3 Autoselect Addresses in System Description Address Read Data (word/byte mode) Manufacturer ID (Base) + 00h xx01h/1h Device ID, Word 1 (Base) + 01h 227Eh/7Eh Device ID, Word 2 (Base) + 0Eh 2228h/28h (GL01GP) 2223h/23h (GL512P) 2222h/22h (GL256P) 2221h/21h (GL128P) Device ID, Word 3 (Base) + 0Fh 2201h/01h Secure Device Verify (Base) + 03h Sector Protect Verify (SA) + 02h 22 For S29GLxxxPH: XX19h/19h = Not Factory Locked. XX99h/99h = Factory Locked. For S29GLxxxPL: XX09h/09h = Not Factory Locked. XX89h/89h = Factory Locked. xx01h/01h = Locked, xx00h/00h = Unlocked S29GL-P MirrorBit(R) Flash Family S29GL-P_00_A7 November 8, 2007 Da ta Shee t (Prelimi nar y) Table 7.4 Autoselect Entry in System (LLD Function = lld_AutoselectEntryCmd) Cycle Operation Byte Address Word Address Data Unlock Cycle 1 Write Unlock Cycle 2 Write Base + AAAh Base + 555h 0x00AAh Base + 555h Base + 2AAh 0x0055h Autoselect Command Write Base + AAAh Base + 555h 0x0090h Software Functions and Sample Code Table 7.5 Autoselect Exit (LLD Function = lld_AutoselectExitCmd) Cycle Operation Byte Address Word Address Data Unlock Cycle 1 Write base + XXXh base + XXXh 0x00F0h Note 1. Any offset within the device works. 2. base = base address. The following is a C source code example of using the autoselect function to read the manufacturer ID. Refer to the Spansion Low Level Driver User's Guide (available on www.spansion.com) for general information on Spansion Flash memory software development guidelines. /* Here is an example of Autoselect mode (getting manufacturer ID) */ /* Define UINT16 example: typedef unsigned short UINT16; */ UINT16 manuf_id; /* Auto Select Entry */ *( (UINT16 *)base_addr + 0x555 ) = 0x00AA; /* write unlock cycle 1 */ *( (UINT16 *)base_addr + 0x2AA ) = 0x0055; /* write unlock cycle 2 */ *( (UINT16 *)base_addr + 0x555 ) = 0x0090; /* write autoselect command */ /* multiple reads can be performed after entry */ manuf_id = *( (UINT16 *)base_addr + 0x000 ); /* read manuf. id */ /* Autoselect exit */ *( (UINT16 *)base_addr + 0x000 ) = 0x00F0; /* exit autoselect (write reset command) */ November 8, 2007 S29GL-P_00_A7 S29GL-P MirrorBit(R) Flash Family 23 Data 7.7 Sheet (Pre limin ar y) Program/Erase Operations These devices are capable of several modes of programming and or erase operations which are described in detail in the following sections. During a write operation, the system must drive CE# and WE# to VIL and OE# to VIH when providing address, command, and data. Addresses are latched on the last falling edge of WE# or CE#, while data is latched on the 1st rising edge of WE# or CE#. The Unlock Bypass feature allows the host system to send program commands to the Flash device without first writing unlock cycles within the command sequence. See Section 7.7.8 for details on the Unlock Bypass function. Note the following: When the Embedded Program algorithm is complete, the device returns to the read mode. The system can determine the status of the program operation by reading the DQ status bits. Refer to the Write Operation Status on page 36 for information on these status bits. An "0" cannot be programmed back to a "1." A succeeding read shows that the data is still "0." Only erase operations can convert a "0" to a "1." Any commands written to the device during the Embedded Program/Erase are ignored except the Suspend commands. Secured Silicon Sector, Autoselect, and CFI functions are unavailable when a program operation is in progress. A hardware reset and/or power removal immediately terminates the Program/Erase operation and the Program/Erase command sequence should be reinitiated once the device has returned to the read mode to ensure data integrity. Programming is allowed in any sequence and across sector boundaries for single word programming operation. See Write Buffer Programming on page 26 when using the write buffer. Programming to the same word address multiple times without intervening erases is permitted. 7.7.1 Single Word Programming Single word programming mode is one method of programming the Flash. In this mode, four Flash command write cycles are used to program an individual Flash address. The data for this programming operation could be 8 or 16-bits wide. While the single word programming method is supported by most Spansion devices, in general Single Word Programming is not recommended for devices that support Write Buffer Programming. See Table 12.1 on page 68 for the required bus cycles and Figure 7.1 for the flowchart. When the Embedded Program algorithm is complete, the device then returns to the read mode and addresses are no longer latched. The system can determine the status of the program operation by reading the DQ status bits. Refer to Write Operation Status on page 36 for information on these status bits. During programming, any command (except the Suspend Program command) is ignored. The Secured Silicon Sector, Autoselect, and CFI functions are unavailable when a program operation is in progress. A hardware reset immediately terminates the program operation. The program command sequence should be reinitiated once the device has returned to the read mode, to ensure data integrity. Programming to the same address multiple times continuously (for example, "walking" a bit within a word) is permitted. 24 S29GL-P MirrorBit(R) Flash Family S29GL-P_00_A7 November 8, 2007 Da ta Shee t (Prelimi nar y) Figure 7.1 Single Word Program Write Unlock Cycles: Address 555h, Data AAh Address 2AAh, Data 55h Unlock Cycle 1 Unlock Cycle 2 Write Program Command: Address 555h, Data A0h Setup Command Program Address (PA), Program Data (PD) Program Data to Address: PA, PD Perform Polling Algorithm (see Write Operation Status flowchart) Polling Status = Busy? Yes No Yes Polling Status = Done? Error condition (Exceeded Timing Limits) No PASS. Device is in read mode. November 8, 2007 S29GL-P_00_A7 FAIL. Issue reset command to return to read array mode. S29GL-P MirrorBit(R) Flash Family 25 Data Sheet (Pre limin ar y) Software Functions and Sample Code Table 7.6 Single Word/Byte Program (LLD Function = lld_ProgramCmd) Cycle Operation Byte Address Word Address Data Unlock Cycle 1 Write Unlock Cycle 2 Write Base + AAAh Base + 555h 00AAh Base + 555h Base + 2AAh 0055h Program Setup Write Program Write Base + AAAh Base + 555h 00A0h Byte Address Word Address Data Note Base = Base Address. The following is a C source code example of using the single word program function. Refer to the Spansion Low Level Driver User's Guide (available on www.spansion.com) for general information on Spansion Flash memory software development guidelines. /* Example: Program Command */ *( (UINT16 *)base_addr + 0x555 ) *( (UINT16 *)base_addr + 0x2AA ) *( (UINT16 *)base_addr + 0x555 ) *( (UINT16 *)pa ) /* Poll for program completion */ 7.7.2 = = = = 0x00AA; 0x0055; 0x00A0; data; /* /* /* /* write write write write unlock cycle 1 unlock cycle 2 program setup command data to be programmed */ */ */ */ Write Buffer Programming Write Buffer Programming allows the system to write a maximum of 32 words in one programming operation. This results in a faster effective word programming time than the standard "word" programming algorithms. The Write Buffer Programming command sequence is initiated by first writing two unlock cycles. This is followed by a third write cycle containing the Write Buffer Load command written at the Sector Address in which programming occurs. At this point, the system writes the number of "word locations minus 1" that are loaded into the page buffer at the Sector Address in which programming occurs. This tells the device how many write buffer addresses are loaded with data and therefore when to expect the "Program Buffer to Flash" confirm command. The number of locations to program cannot exceed the size of the write buffer or the operation aborts. (Number loaded = the number of locations to program minus 1. For example, if the system programs 6 address locations, then 05h should be written to the device.) The system then writes the starting address/data combination. This starting address is the first address/data pair to be programmed, and selects the "write-buffer-page" address. All subsequent address/data pairs must fall within the elected-write-buffer-page. The "write-buffer-page" is selected by using the addresses AMAX-A5. The "write-buffer-page" addresses must be the same for all address/data pairs loaded into the write buffer. (This means Write Buffer Programming cannot be performed across multiple "write-buffer-pages." This also means that Write Buffer Programming cannot be performed across multiple sectors. If the system attempts to load programming data outside of the selected "write-buffer-page", the operation ABORTs.) After writing the Starting Address/Data pair, the system then writes the remaining address/data pairs into the write buffer. Note that if a Write Buffer address location is loaded multiple times, the "address/data pair" counter is decremented for every data load operation. Also, the last data loaded at a location before the "Program Buffer to Flash" confirm command is the data programmed into the device. It is the software's responsibility to comprehend ramifications of loading a write-buffer location more than once. The counter decrements for each data load operation, NOT for each unique write-buffer-address location. Once the specified number of write buffer locations have been loaded, the system must then write the "Program Buffer to Flash" command at the Sector Address. Any other address/data write combinations abort the Write Buffer Programming operation. The Write Operation Status bits should be used while monitoring the last address location loaded into the write buffer. This eliminates the need to store an address in memory because the system can load the last address location, issue the program confirm command at the last loaded address location, and then check the write operation status at that same address. DQ7, DQ6, DQ5, DQ2, and DQ1 should be monitored to determine the device status during Write Buffer Programming. 26 S29GL-P MirrorBit(R) Flash Family S29GL-P_00_A7 November 8, 2007 Da ta Shee t (Prelimi nar y) The write-buffer "embedded" programming operation can be suspended using the standard suspend/resume commands. Upon successful completion of the Write Buffer Programming operation, the device returns to READ mode. The Write Buffer Programming Sequence is ABORTED under any of the following conditions: Load a value that is greater than the page buffer size during the "Number of Locations to Program" step. Write to an address in a sector different than the one specified during the Write-Buffer-Load command. Write an Address/Data pair to a different write-buffer-page than the one selected by the "Starting Address" during the "write buffer data loading" stage of the operation. Writing anything other than the Program to Buffer Flash Command after the specified number of "data load" cycles. The ABORT condition is indicated by DQ1 = 1, DQ7 = DATA# (for the "last address location loaded"), DQ6 = TOGGLE, DQ5 = 0. This indicates that the Write Buffer Programming Operation was ABORTED. A "Write-toBuffer-Abort reset" command sequence is required when using the write buffer Programming features in Unlock Bypass mode. Note that the Secured Silicon sector, autoselect, and CFI functions are unavailable when a program operation is in progress. Write buffer programming is allowed in any sequence of memory (or address) locations. These flash devices are capable of handling multiple write buffer programming operations on the same write buffer address range without intervening erases. Use of the write buffer is strongly recommended for programming when multiple words are to be programmed. November 8, 2007 S29GL-P_00_A7 S29GL-P MirrorBit(R) Flash Family 27 Data Sheet (Pre limin ar y) Software Functions and Sample Code Table 7.7 Write Buffer Program (LLD Functions Used = lld_WriteToBufferCmd, lld_ProgramBufferToFlashCmd) Cycle Description Operation Byte Address Word Address Data 1 Unlock Write Base + AAAh Base + 555h 00AAh 2 Unlock Write Base + 555h Base + 2AAh 0055h 3 Write Buffer Load Command Write Sector Address 0025h 4 Write Word Count Write Sector Address Word Count (N-1)h Number of words (N) loaded into the write buffer can be from 1 to 32 words (1 to 64 bytes). 5 to 36 Load Buffer Word N Write Program Address, Word N Word N Last Write Buffer to Flash Write Sector Address 0029h Notes 1. Base = Base Address. 2. Last = Last cycle of write buffer program operation; depending on number of words written, the total number of cycles may be from 6 to 37. 3. For maximum efficiency, it is recommended that the write buffer be loaded with the highest number of words (N words) possible. The following is a C source code example of using the write buffer program function. Refer to the Spansion Low Level Driver User's Guide (available on www.spansion.com) for general information on Spansion Flash memory software development guidelines. /* Example: Write Buffer Programming Command */ /* NOTES: Write buffer programming limited to 16 words. */ /* All addresses to be written to the flash in */ /* one operation must be within the same flash */ /* page. A flash page begins at addresses */ /* evenly divisible by 0x20. */ UINT16 *src = source_of_data; /* address of source data */ UINT16 *dst = destination_of_data; /* flash destination address */ UINT16 wc = words_to_program -1; /* word count (minus 1) */ *( (UINT16 *)base_addr + 0x555 ) = 0x00AA; /* write unlock cycle 1 */ *( (UINT16 *)base_addr + 0x2AA ) = 0x0055; /* write unlock cycle 2 */ *( (UINT16 *)sector_address ) = 0x0025; /* write write buffer load command */ *( (UINT16 *)sector_address ) = wc; /* write word count (minus 1) */ for (i=0;i<=wc;i++) { *dst++ = *src++; /* ALL dst MUST BE in same Write Buffer */ } *( (UINT16 *)sector_address ) /* poll for completion */ = 0x0029; /* write confirm command */ /* Example: Write Buffer Abort Reset */ *( (UINT16 *)addr + 0x555 ) = 0x00AA; *( (UINT16 *)addr + 0x2AA ) = 0x0055; *( (UINT16 *)addr + 0x555 ) = 0x00F0; 28 /* write unlock cycle 1 /* write unlock cycle 2 /* write buffer abort reset S29GL-P MirrorBit(R) Flash Family */ */ */ S29GL-P_00_A7 November 8, 2007 Da ta Shee t (Prelimi nar y) Figure 7.2 Write Buffer Programming Operation Write Unlock Cycles: Address 555h, Data AAh Address 2AAh, Data 55h Unlock Cycle 1 Unlock Cycle 2 Issue Write Buffer Load Command: Address SA, Data 25h Load Word Count to Program Program Data to Address: SA, wc wc = number of words - 1 Yes Confirm command: SA = 0x29h wc = 0? No Write Next Word, Decrement wc: wc = wc - 1 No Perform Polling Algorithm Write Buffer Abort Desired? (see Write Operation Status flowchart) Yes Polling Status = Done? Write to a Different Sector Address to Cause Write Buffer Abort Yes No No Error? Yes Yes Write Buffer Abort? No RESET. Issue Write Buffer Abort Reset Command November 8, 2007 S29GL-P_00_A7 FAIL. Issue reset command to return to read array mode. S29GL-P MirrorBit(R) Flash Family PASS. Device is in read mode. 29 Data 7.7.3 Sheet (Pre limin ar y) Sector Erase The sector erase function erases one or more sectors in the memory array. (See Table 12.1 on page 68 and Figure 7.3.) The device does not require the system to preprogram a sector prior to erase. The Embedded Erase algorithm automatically programs and verifies the entire memory to an all zero data pattern prior to electrical erase. After a successful sector erase, all locations within the erased sector contain FFFFh. The system is not required to provide any controls or timings during these operations. After the command sequence is written, a sector erase time-out of no less than tSEA occurs. During the timeout period, additional sector addresses may be written. Loading the sector erase buffer may be done in any sequence, and the number of sectors may be from one sector to all sectors. The time between these additional cycles must be less than 50 s. Any sector erase address and command following the exceeded time-out (50s) may or may not be accepted. Any command other than Sector Erase or Erase Suspend during the time-out period resets that sector to the read mode. The system can monitor DQ3 to determine if the sector erase timer has timed out (See Section 7.8.6.) The time-out begins from the rising edge of the final WE# pulse in the command sequence. When the Embedded Erase algorithm is complete, the sector returns to reading array data and addresses are no longer latched. The system can determine the status of the erase operation by reading DQ7 or DQ6/DQ2 in the erasing sector. Refer to Section 7.8 for information on these status bits. Once the sector erase operation has begun, only the Erase Suspend command is valid. All other commands are ignored. However, note that a hardware reset immediately terminates the erase operation. If that occurs, the sector erase command sequence should be reinitiated once that sector has returned to reading array data, to ensure the sector is properly erased. The Unlock Bypass feature allows the host system to send program commands to the Flash device without first writing unlock cycles within the command sequence. See Section 7.7.8 for details on the Unlock Bypass function. Figure 7.3 illustrates the algorithm for the erase operation. Refer to Section 11.7.5 for parameters and timing diagrams. Software Functions and Sample Code Table 7.8 Sector Erase (LLD Function = lld_SectorEraseCmd) Cycle Description Operation Byte Address Word Address Data 1 Unlock Write Base + AAAh Base + 555h 00AAh 2 Unlock Write Base + 555h Base + 2AAh 0055h 3 Setup Command Write Base + AAAh Base + 555h 0080h 4 Unlock Write Base + AAAh Base + 555h 00AAh 5 Unlock Write Base + 555h Base + 2AAh 0055h Sector Erase Command Write Sector Address Sector Address 0030h 6 Unlimited additional sectors may be selected for erase; command(s) must be written within 50 s. The following is a C source code example of using the sector erase function. Refer to the Spansion Low Level Driver User's Guide (available on www.spansion.com) for general information on Spansion Flash memory software development guidelines. /* Example: Sector Erase Command */ *( *( *( *( *( *( 30 (UINT16 (UINT16 (UINT16 (UINT16 (UINT16 (UINT16 *)base_addr + 0x555 *)base_addr + 0x2AA *)base_addr + 0x555 *)base_addr + 0x555 *)base_addr + 0x2AA *)sector_address ) ) ) ) ) ) = = = = = = 0x00AA; 0x0055; 0x0080; 0x00AA; 0x0055; 0x0030; /* /* /* /* /* /* write write write write write write S29GL-P MirrorBit(R) Flash Family unlock cycle 1 */ unlock cycle 2 */ setup command */ additional unlock cycle 1 */ additional unlock cycle 2 */ sector erase command */ S29GL-P_00_A7 November 8, 2007 Da ta Shee t (Prelimi nar y) Figure 7.3 Sector Erase Operation Write Unlock Cycles: Address 555h, Data AAh Address 2AAh, Data 55h Unlock Cycle 1 Unlock Cycle 2 Write Sector Erase Cycles: Address 555h, Data 80h Address 555h, Data AAh Address 2AAh, Data 55h Sector Address, Data 30h No Command Cycle 1 Command Cycle 2 Command Cycle 3 Specify first sector for erasure Select Additional Sectors? Yes Write Additional Sector Addresses * Each additional cycle must be written within tSEA timeout * The host system may monitor DQ3 or wait tSEA to ensure acceptance of erase commands * No limit on number of sectors No Yes Poll DQ3. DQ3 = 1? Last Sector Selected? * Commands other than Erase Suspend or selecting additional sectors for erasure during timeout reset device to reading array data No Yes Perform Write Operation Status Algorithm (see Figure 7.4) Yes Status may be obtained by reading DQ7, DQ6 and/or DQ2. Done? No No DQ5 = 1? Error condition (Exceeded Timing Limits) Yes PASS. Device returns to reading array. FAIL. Write reset command to return to reading array. Notes 1. See Table 12.1 on page 68 for erase command sequence. 2. See DQ3: Sector Erase Timeout State Indicator on page 39 for information on the sector erase timeout. November 8, 2007 S29GL-P_00_A7 S29GL-P MirrorBit(R) Flash Family 31 Data 7.7.4 Sheet (Pre limin ar y) Chip Erase Command Sequence Chip erase is a six-bus cycle operation as indicated by Table 12.1 on page 68. These commands invoke the Embedded Erase algorithm, which does not require the system to preprogram prior to erase. The Embedded Erase algorithm automatically preprograms and verifies the entire memory to an all zero data pattern prior to electrical erase. After a successful chip erase, all locations of the chip contain FFFFh. The system is not required to provide any controls or timings during these operations. The Command Definitions on page 67 shows the address and data requirements for the chip erase command sequence. When the Embedded Erase algorithm is complete, that sector returns to the read mode and addresses are no longer latched. The system can determine the status of the erase operation by using DQ7 or DQ6/DQ2. Refer to "Write Operation Status" for information on these status bits. The Unlock Bypass feature allows the host system to send program commands to the Flash device without first writing unlock cycles within the command sequence. See Section 7.7.8 for details on the Unlock Bypass function. Any commands written during the chip erase operation are ignored. However, note that a hardware reset immediately terminates the erase operation. If that occurs, the chip erase command sequence should be reinitiated once that sector has returned to reading array data, to ensure the entire array is properly erased. Software Functions and Sample Code Table 7.9 Chip Erase (LLD Function = lld_ChipEraseCmd) Cycle Description Operation Byte Address Word Address Data 1 Unlock Write Base + AAAh Base + 555h 00AAh 2 Unlock Write Base + 555h Base + 2AAh 0055h 3 Setup Command Write Base + AAAh Base + 555h 0080h 4 Unlock Write Base + AAAh Base + 555h 00AAh 5 Unlock Write Base + 555h Base + 2AAh 0055h 6 Chip Erase Command Write Base + AAAh Base + 555h 0010h The following is a C source code example of using the chip erase function. Refer to the Spansion Low Level Driver User's Guide (available on www.spansion.com) for general information on Spansion Flash memory software development guidelines. /* Example: Chip Erase Command */ /* Note: Cannot be suspended */ *( (UINT16 *)base_addr + 0x555 ) *( (UINT16 *)base_addr + 0x2AA ) *( (UINT16 *)base_addr + 0x555 ) *( (UINT16 *)base_addr + 0x555 ) *( (UINT16 *)base_addr + 0x2AA ) *( (UINT16 *)base_addr + 0x000 ) 32 = = = = = = 0x00AA; 0x0055; 0x0080; 0x00AA; 0x0055; 0x0010; /* /* /* /* /* /* write write write write write write S29GL-P MirrorBit(R) Flash Family unlock cycle 1 */ unlock cycle 2 */ setup command */ additional unlock cycle 1 */ additional unlock cycle 2 */ chip erase command */ S29GL-P_00_A7 November 8, 2007 Da ta 7.7.5 Shee t (Prelimi nar y) Erase Suspend/Erase Resume Commands The Erase Suspend command allows the system to interrupt a sector erase operation and then read data from, or program data to, any sector not selected for erasure. The sector address is required when writing this command. This command is valid only during the sector erase operation, including the minimum tSEA time-out period during the sector erase command sequence. The Erase Suspend command is ignored if written during the chip erase operation. When the Erase Suspend command is written during the sector erase operation, the device requires a maximum of 20 s (5 s typical) to suspend the erase operation. However, when the Erase Suspend command is written during the sector erase time-out, the device immediately terminates the time-out period and suspends the erase operation. After the erase operation has been suspended, the device enters the erase-suspend-read mode. The system can read data from or program data to any sector not selected for erasure. (The device "erase suspends" all sectors selected for erasure.) Reading at any address within erase-suspended sectors produces status information on DQ7-DQ0. The system can use DQ7, or DQ6, and DQ2 together, to determine if a sector is actively erasing or is erase-suspended. Refer to Table 7.35 for information on these status bits. After an erase-suspended program operation is complete, the device returns to the erase-suspend-read mode. The system can determine the status of the program operation using write operation status bits, just as in the standard program operation. In the erase-suspend-read mode, the system can also issue the Autoselect command sequence. Refer to Write Buffer Programming on page 26 and the Autoselect on page 21 for details. To resume the sector erase operation, the system must write the Erase Resume command. The address of the erase-suspended sector is required when writing this command. Further writes of the Resume command are ignored. Another Erase Suspend command can be written after the chip has resumed erasing. Software Functions and Sample Code Table 7.10 Erase Suspend (LLD Function = lld_EraseSuspendCmd) Cycle Operation Byte Address Word Address Data 1 Write Base + XXXh Base + XXXh 00B0h The following is a C source code example of using the erase suspend function. Refer to the Spansion Low Level Driver User's Guide (available on www.spansion.com) for general information on Spansion Flash memory software development guidelines. /* Example: Erase suspend command */ *( (UINT16 *)base_addr ) = 0x00B0; /* write suspend command */ Table 7.11 Erase Resume (LLD Function = lld_EraseResumeCmd) Cycle Operation Byte Address Word Address Data 1 Write Sector Address Sector Address 0030h The following is a C source code example of using the erase resume function. Refer to the Spansion Low Level Driver User's Guide (available on www.spansion.com) for general information on Spansion Flash memory software development guidelines. /* Example: Erase resume command */ *( (UINT16 *)sector_addr ) = 0x0030; /* write resume command /* The flash needs adequate time in the resume state */ November 8, 2007 S29GL-P_00_A7 S29GL-P MirrorBit(R) Flash Family */ 33 Data 7.7.6 Sheet (Pre limin ar y) Program Suspend/Program Resume Commands The Program Suspend command allows the system to interrupt an embedded programming operation or a "Write to Buffer" programming operation so that data can read from any non-suspended sector. When the Program Suspend command is written during a programming process, the device halts the programming operation within 15 s maximum (5 s typical) and updates the status bits. Addresses are "don't-cares" when writing the Program Suspend command. After the programming operation has been suspended, the system can read array data from any nonsuspended sector. The Program Suspend command may also be issued during a programming operation while an erase is suspended. In this case, data may be read from any addresses not within a sector in Erase Suspend or Program Suspend. If a read is needed from the Secured Silicon Sector area, then user must use the proper command sequences to enter and exit this region. The system may also write the Autoselect Command Sequence when the device is in Program Suspend mode. The device allows reading Autoselect codes in the suspended sectors, since the codes are not stored in the memory array. When the device exits the Autoselect mode, the device reverts to Program Suspend mode, and is ready for another valid operation. See Autoselect on page 21 for more information. After the Program Resume command is written, the device reverts to programming. The system can determine the status of the program operation using the write operation status bits, just as in the standard program operation. See Write Operation Status on page 36 for more information. The system must write the Program Resume command (address bits are "don't care") to exit the Program Suspend mode and continue the programming operation. Further writes of the Program Resume command are ignored. Another Program Suspend command can be written after the device has resumed programming. Software Functions and Sample Code Table 7.12 Program Suspend (LLD Function = lld_ProgramSuspendCmd) Cycle Operation Word Address Data 1 Write Base + XXXh 00B0h The following is a C source code example of using the program suspend function. Refer to the Spansion Low Level Driver User's Guide (available on www.spansion.com) for general information on Spansion Flash memory software development guidelines. /* Example: Program suspend command */ *( (UINT16 *)base_addr ) = 0x00B0; /* write suspend command */ Table 7.13 Program Resume (LLD Function = lld_ProgramResumeCmd) Cycle Operation Word Address Data 1 Write Base + XXXh 0030h The following is a C source code example of using the program resume function. Refer to the Spansion Low Level Driver User's Guide (available on www.spansion.com) for general information on Spansion Flash memory software development guidelines. /* Example: Program resume command */ *( (UINT16 *)base_addr ) = 0x0030; 34 /* write resume command S29GL-P MirrorBit(R) Flash Family */ S29GL-P_00_A7 November 8, 2007 Da ta 7.7.7 Shee t (Prelimi nar y) Accelerated Program Accelerated single word programming and write buffer programming operations are enabled through the WP#/ACC pin. This method is faster than the standard program command sequences. Note The accelerated program functions must not be used more than 10 times per sector. If the system asserts VHH on this input, the device automatically enters the aforementioned Unlock Bypass mode and uses the higher voltage on the input to reduce the time required for program operations. The system can then use the Write Buffer Load command sequence provided by the Unlock Bypass mode. Note that if a "Write-to-Buffer-Abort Reset" is required while in Unlock Bypass mode, the full 3-cycle RESET command sequence must be used to reset the device. Removing VHH from the ACC input, upon completion of the embedded program operation, returns the device to normal operation. Sectors must be unlocked prior to raising WP#/ACC to VHH. The WP#/ACC pin must not be at VHH for operations other than accelerated programming, or device damage may result. It is recommended that WP#/ACC apply VHH after power-up sequence is completed. In addition, it is recommended that WP#/ACC apply from VHH to VIH/VIL before powering down VCC/VIO. 7.7.8 Unlock Bypass This device features an Unlock Bypass mode to facilitate shorter programming commands. Once the device enters the Unlock Bypass mode, only two write cycles are required to program data, instead of the normal four cycles. This mode dispenses with the initial two unlock cycles required in the standard program command sequence, resulting in faster total programming time. The Command Definitions on page 67 shows the requirements for the unlock bypass command sequences. During the unlock bypass mode, only the Read, Program, Write Buffer Programming, Write-to-Buffer-Abort Reset, and Unlock Bypass Reset commands are valid. To exit the unlock bypass mode, the system must issue the two-cycle unlock bypass reset command sequence. The first cycle must contain the sector address and the data 90h. The second cycle need only contain the data 00h. The sector then returns to the read mode. Software Functions and Sample Code The following are C source code examples of using the unlock bypass entry, program, and exit functions. Refer to the Spansion Low Level Driver User's Guide (available soon on www.spansion.com) for general information on Spansion Flash memory software development guidelines. Table 7.14 Unlock Bypass Entry (LLD Function = lld_UnlockBypassEntryCmd) Cycle Description Operation Word Address Data 1 Unlock 2 Unlock Write Base + 555h 00AAh Write Base + 2AAh 0055h 3 Entry Command Write Base + 555h 0020h /* Example: Unlock Bypass Entry Command */ *( (UINT16 *)base_addr + 0x555 ) = 0x00AA; /* write unlock *( (UINT16 *)base_addr + 0x2AA ) = 0x0055; /* write unlock *( (UINT16 *)base_addr + 0x555 ) = 0x0020; /* write unlock /* At this point, programming only takes two write cycles. /* Once you enter Unlock Bypass Mode, do a series of like /* operations (programming or sector erase) and then exit /* Unlock Bypass Mode before beginning a different type of /* operations. November 8, 2007 S29GL-P_00_A7 S29GL-P MirrorBit(R) Flash Family cycle 1 cycle 2 bypass command */ */ */ */ */ */ */ */ 35 Data Sheet (Pre limin ar y) Table 7.15 Unlock Bypass Program (LLD Function = lld_UnlockBypassProgramCmd) Cycle Description Operation Word Address 1 Program Setup Command Write Base +xxxh 00A0h 2 Program Command Write Program Address Program Data /* Example: Unlock Bypass Program Command */ /* Do while in Unlock Bypass Entry Mode! */ *( (UINT16 *)base_addr ) = 0x00A0; /* write program setup command */ *( (UINT16 *)pa ) = data; /* write data to be programmed /* Poll until done or error. */ /* If done and more to program, */ /* do above two cycles again. */ Data */ Table 7.16 Unlock Bypass Reset (LLD Function = lld_UnlockBypassResetCmd) Cycle Description Operation Word Address Data 1 Reset Cycle 1 Write Base +xxxh 0090h 2 Reset Cycle 2 Write Base +xxxh 0000h /* Example: Unlock Bypass Exit Command */ *( (UINT16 *)base_addr ) = 0x0090; *( (UINT16 *)base_addr ) = 0x0000; 7.8 Write Operation Status The device provides several bits to determine the status of a program or erase operation. The following subsections describe the function of DQ1, DQ2, DQ3, DQ5, DQ6, and DQ7. 7.8.1 DQ7: Data# Polling The Data# Polling bit, DQ7, indicates to the host system whether an Embedded Program or Erase algorithm is in progress or completed, or whether the device is in Erase Suspend. Data# Polling is valid after the rising edge of the final WE# pulse in the command sequence. Note that the Data# Polling is valid only for the last word being programmed in the write-buffer-page during Write Buffer Programming. Reading Data# Polling status on any word other than the last word to be programmed in the write-buffer-page returns false status information. During the Embedded Program algorithm, the device outputs on DQ7 the complement of the datum programmed to DQ7. This DQ7 status also applies to programming during Erase Suspend. When the Embedded Program algorithm is complete, the device outputs the datum programmed to DQ7. The system must provide the program address to read valid status information on DQ7. If a program address falls within a protected sector, Data# polling on DQ7 is active, then that sector returns to the read mode. During the Embedded Erase Algorithm, Data# polling produces a "0" on DQ7. When the Embedded Erase algorithm is complete, or if the device enters the Erase Suspend mode, Data# Polling produces a "1" on DQ7. The system must provide an address within any of the sectors selected for erasure to read valid status information on DQ7. After an erase command sequence is written, if all sectors selected for erasing are protected, Data# Polling on DQ7 is active for approximately 100 s, then the device returns to the read mode. If not all selected sectors are protected, the Embedded Erase algorithm erases the unprotected sectors, and ignores the selected sectors that are protected. However, if the system reads DQ7 at an address within a protected sector, the status may not be valid. Just prior to the completion of an Embedded Program or Erase operation, DQ7 may change asynchronously with DQ6-DQ0 while Output Enable (OE#) is asserted low. That is, the device may change from providing status information to valid data on DQ7. Depending on when the system samples the DQ7 output, it may read 36 S29GL-P MirrorBit(R) Flash Family S29GL-P_00_A7 November 8, 2007 Da ta Shee t (Prelimi nar y) the status or valid data. Even if the device has completed the program or erase operation and DQ7 has valid data, the data outputs on DQ6-DQ0 may be still invalid. Valid data on DQ7-D00 appears on successive read cycles. See the following for more information: Table 7.17, shows the outputs for Data# Polling on DQ7. Figure 7.4, shows the Data# Polling algorithm; and Figure 11.7, shows the Data# Polling timing diagram. Figure 7.4 Write Operation Status Flowchart START Read 1 (Note 6) YES Program Operation Complete DQ7=valid data? NO YES YES Read 2 Read 1 DQ5=1? Read3= valid data? NO NO Read 3 Read 2 Program Operation Failed YES Write Buffer Programming? YES NO Programming Operation? Read 3 NO Device BUSY, Re-Poll (Note 3) (Note 1) (Note 4) YES DQ6 toggling? TIMEOUT NO YES (Note 5) (Note 1) YES DQ6 toggling? NO Read1 DQ1=1? (Note 2) NO DEVICE ERROR Device BUSY, Re-Poll YES DQ2 toggling? NO Read 2 Device BUSY, Re-Poll Erase Operation Complete Read 3 YES Read3 DQ1=1 AND DQ7 ? Valid Data? NO Device BUSY, Re-Poll November 8, 2007 S29GL-P_00_A7 Write Buffer Operation Failed Device in Erase/Suspend Mode Notes: 1) DQ6 is toggling if Read2 DQ6 does not equal Read3 DQ6. 2) DQ2 is toggling if Read2 DQ2 does not equal Read3 DQ2. 3) May be due to an attempt to program a 0 to 1. Use the RESET command to exit operation. 4) Write buffer error if DQ1 of last read =1. 5) Invalid state, use RESET command to exit operation. 6) Valid data is the data that is intended to be programmed or all 1's for an erase operation. 7) Data polling algorithm valid for all operations except advanced sector protection. S29GL-P MirrorBit(R) Flash Family 37 Data 7.8.2 Sheet (Pre limin ar y) DQ6: Toggle Bit I Toggle Bit I on DQ6 indicates whether an Embedded Program or Erase algorithm is in progress or complete, or whether the device has entered the Erase Suspend mode. Toggle Bit I may be read at any address, and is valid after the rising edge of the final WE# pulse in the command sequence (prior to the program or erase operation), and during the sector erase time-out. During an Embedded Program or Erase algorithm operation, successive read cycles to any address that is being programmed or erased causes DQ6 to toggle. When the operation is complete, DQ6 stops toggling. After an erase command sequence is written, if all sectors selected for erasing are protected, DQ6 toggles for approximately 100s, then returns to reading array data. If not all selected sectors are protected, the Embedded Erase algorithm erases the unprotected sectors, and ignores the selected sectors that are protected. The system can use DQ6 and DQ2 together to determine whether a sector is actively erasing or is erasesuspended. When the device is actively erasing (that is, the Embedded Erase algorithm is in progress), DQ6 toggles. When the device enters the Erase Suspend mode, DQ6 stops toggling. However, the system must also use DQ2 to determine which sectors are erasing or erase-suspended. Alternatively, the system can use DQ7 (see DQ7: Data# Polling on page 36). If a program address falls within a protected sector, DQ6 toggles for approximately 1s after the program command sequence is written, then returns to reading array data. DQ6 also toggles during the erase-suspend-program mode, and stops toggling once the Embedded Program Algorithm is complete. See the following for additional information: Figure 7.4, Figure 11.13 on page 63, and Table 7.17. Toggle Bit I on DQ6 requires either OE# or CE# to be de-asserted and reasserted to show the change in state. 7.8.3 DQ2: Toggle Bit II The "Toggle Bit II" on DQ2, when used with DQ6, indicates whether a particular sector is actively erasing (that is, the Embedded Erase algorithm is in progress), or whether that sector is erase-suspended. Toggle Bit II is valid after the rising edge of the final WE# pulse in the command sequence. DQ2 toggles when the system reads at addresses within those sectors that have been selected for erasure. But DQ2 cannot distinguish whether the sector is actively erasing or is erase-suspended. DQ6, by comparison, indicates whether the device is actively erasing, or is in Erase Suspend, but cannot distinguish which sectors are selected for erasure. Thus, both status bits are required for sector and mode information. Refer to Table 7.17 to compare outputs for DQ2 and DQ6. See Figure 11.14 on page 63 for additional information. 7.8.4 Reading Toggle Bits DQ6/DQ2 Whenever the system initially begins reading toggle bit status, it must read DQ7-DQ0 at least twice in a row to determine whether a toggle bit is toggling. Typically, the system would note and store the value of the toggle bit after the first read. After the second read, the system would compare the new value of the toggle bit with the first. If the toggle bit is not toggling, the device has completed the program or erases operation. The system can read array data on DQ7-DQ0 on the following read cycle. However, if after the initial two read cycles, the system determines that the toggle bit is still toggling, the system also should note whether the value of DQ5 is high (see DQ5: Exceeded Timing Limits on page 39). If it is, the system should then determine again whether the toggle bit is toggling, since the toggle bit may have stopped toggling just as DQ5 went high. If the toggle bit is no longer toggling, the device has successfully completed the program or erases operation. If it is still toggling, the device did not complete the operation successfully, and the system must write the reset command to return to reading array data. The remaining scenario is that the system initially determines that the toggle bit is toggling and DQ5 has not gone high. The system may continue to monitor the toggle bit and DQ5 through successive read cycles, determining the status as described in the previous paragraph. Alternatively, it may choose to perform other system tasks. In this case, the system must start at the beginning of the algorithm when it returns to determine the status of the operation. Refer to Figure 7.4 for more details. Note When verifying the status of a write operation (embedded program/erase) of a memory sector, DQ6 and DQ2 toggle between high and low states in a series of consecutive and contiguous status read cycles. In order for 38 S29GL-P MirrorBit(R) Flash Family S29GL-P_00_A7 November 8, 2007 Da ta Shee t (Prelimi nar y) this toggling behavior to be properly observed, the consecutive status bit reads must not be interleaved with read accesses to other memory sectors. If it is not possible to temporarily prevent reads to other memory sectors, then it is recommended to use the DQ7 status bit as the alternative method of determining the active or inactive status of the write operation. 7.8.5 DQ5: Exceeded Timing Limits DQ5 indicates whether the program or erase time has exceeded a specified internal pulse count limit. Under these conditions DQ5 produces a "1," indicating that the program or erase cycle was not successfully completed. The device does not output a 1 on DQ5 if the system tries to program a 1 to a location that was previously programmed to 0. Only an erase operation can change a 0 back to a 1. Under this condition, the device ignores the bit that was incorrectly instructed to be programmed from a 0 to a 1, while any other bits that were correctly requested to be changed from 1 to 0 are programmed. Attempting to program a 0 to a 1 is masked during the programming operation. Under valid DQ5 conditions, the system must write the reset command to return to the read mode (or to the erase-suspend-read mode if a sector was previously in the erase-suspend-program mode). 7.8.6 DQ3: Sector Erase Timeout State Indicator After writing a sector erase command sequence, the system may read DQ3 to determine whether or not erasure has begun. (The sector erase timer does not apply to the chip erase command.) If additional sectors are selected for erasure, the entire time-out also applies after each additional sector erase command. When the time-out period is complete, DQ3 switches from a "0" to a "1." If the time between additional sector erase commands from the system can be assumed to be less than tSEA, then the system need not monitor DQ3. See Sector Erase on page 30 for more details. After the sector erase command is written, the system should read the status of DQ7 (Data# Polling) or DQ6 (Toggle Bit I) to ensure that the device has accepted the command sequence, and then read DQ3. If DQ3 is "1," the Embedded Erase algorithm has begun; all further commands (except Erase Suspend) are ignored until the erase operation is complete. If DQ3 is "0," the device accepts additional sector erase commands. To ensure the command has been accepted, the system software should check the status of DQ3 prior to and following each sub-sequent sector erase command. If DQ3 is high on the second status check, the last command might not have been accepted. Table 7.17 shows the status of DQ3 relative to the other status bits. 7.8.7 DQ1: Write to Buffer Abort DQ1 indicates whether a Write to Buffer operation was aborted. Under these conditions DQ1 produces a "1". The system must issue the "Write to Buffer Abort Reset" command sequence to return the device to reading array data. See Write Buffer Programming on page 26 for more details. November 8, 2007 S29GL-P_00_A7 S29GL-P MirrorBit(R) Flash Family 39 Data Sheet (Pre limin ar y) Table 7.17 Write Operation Status DQ7 (Note 2) DQ6 DQ5 (Note 1) DQ3 DQ2 (Note 2) DQ1 RY/ BY# Embedded Program Algorithm DQ7# Toggle 0 N/A No toggle 0 0 Embedded Erase Algorithm 0 Toggle 0 1 Toggle N/A 0 Status Standard Mode Program Suspend Mode Erase Suspend Mode ProgramSuspend Read EraseSuspend Read Program-Suspended Sector Invalid (not allowed) 1 Non-Program Suspended Sector Data 1 Erase-Suspended Sector 1 No toggle 0 Non-Erase Suspended Sector N/A Toggle N/A Data 1 1 Erase-Suspend-Program (Embedded Program) DQ7# Toggle 0 N/A N/A N/A 0 Busy (Note 3) DQ7# Toggle 0 N/A N/A 0 0 Abort (Note 4) DQ7# Toggle 0 N/A N/A 1 0 Write-toBuffer Notes 1. DQ5 switches to 1 when an Embedded Program, Embedded Erase, or Write-to-Buffer operation has exceeded the maximum timing limits. Refer toDQ5: Exceeded Timing Limits on page 39 for more information. 2. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate subsection for further details. 3. The Data# Polling algorithm should be used to monitor the last loaded write-buffer address location. 4. DQ1 switches to 1 when the device has aborted the write-to-buffer operation 7.9 Writing Commands/Command Sequences During a write operation, the system must drive CE# and WE# to VIL and OE# to VIH when providing an address, command, and data. Addresses are latched on the last falling edge of WE# or CE#, while data is latched on the 1st rising edge of WE# or CE#. An erase operation can erase one sector, multiple sectors, or the entire device. Table 6.2-Table 6.3 indicate the address space that each sector occupies. The device address space is divided into uniform 64KW/128KB sectors. A sector address is the set of address bits required to uniquely select a sector. ICC2 in "DC Characteristics" represents the active current specification for the write mode. "AC Characteristics" contains timing specification tables and timing diagrams for write operations. 7.9.1 RY/BY# The RY/BY# is a dedicated, open-drain output pin that indicates whether an Embedded Algorithm is in progress or complete. The RY/BY# status is valid after the rising edge of the final WE# pulse in the command sequence. Since RY/BY# is an open-drain output, several RY/BY# pins can be tied together in parallel with a pull-up resistor to VCC. This feature allows the host system to detect when data is ready to be read by simply monitoring the RY/BY# pin, which is a dedicated output and controlled by CE# (not OE#). 7.9.2 Hardware Reset The RESET# input provides a hardware method of resetting the device to reading array data. When RESET# is driven low for at least a period of tRP (RESET# Pulse Width), the device immediately terminates any operation in progress, tristates all outputs, resets the configuration register, and ignores all read/write commands for the duration of the RESET# pulse. The device also resets the internal state machine to reading array data. To ensure data integrity Program/Erase operations that were interrupted should be reinitiated once the device is ready to accept another command sequence. When RESET# is held at VSS, the device draws VCC reset current (ICC5). If RESET# is held at VIL, but not at VSS, the standby current is greater. RESET# may be tied to the system reset circuitry which enables the system to read the boot-up firmware from the Flash memory upon a system reset. See Figure 11.7 on page 58 and Figure 11.8 on page 59 for timing diagrams. 40 S29GL-P MirrorBit(R) Flash Family S29GL-P_00_A7 November 8, 2007 Da ta 7.9.3 Shee t (Prelimi nar y) Software Reset Software reset is part of the command set (see Table 12.1 on page 68) that also returns the device to array read mode and must be used for the following conditions: 1. to exit Autoselect mode 2. when DQ5 goes high during write status operation that indicates program or erase cycle was not successfully completed 3. exit sector lock/unlock operation. 4. to return to erase-suspend-read mode if the device was previously in Erase Suspend mode. 5. after any aborted operations Software Functions and Sample Code Table 7.18 Reset (LLD Function = lld_ResetCmd) Cycle Operation Byte Address Word Address Data Reset Command Write Base + xxxh Base + xxxh 00F0h Note Base = Base Address. The following is a C source code example of using the reset function. Refer to the Spansion Low Level Driver User's Guide (available on www.spansion.com) for general information on Spansion Flash memory software development guidelines. /* Example: Reset (software reset of Flash state machine) */ *( (UINT16 *)base_addr ) = 0x00F0; The following are additional points to consider when using the reset command: This command resets the sectors to the read and address bits are ignored. Reset commands are ignored during program and erase operations. The reset command may be written between the cycles in a program command sequence before programming begins (prior to the third cycle). This resets the sector to which the system was writing to the read mode. If the program command sequence is written to a sector that is in the Erase Suspend mode, writing the reset command returns that sector to the erase-suspend-read mode. The reset command may be written during an Autoselect command sequence. If a sector has entered the Autoselect mode while in the Erase Suspend mode, writing the reset command returns that sector to the erase-suspend-read mode. If DQ1 goes high during a Write Buffer Programming operation, the system must write the "Write to Buffer Abort Reset" command sequence to RESET the device to reading array data. The standard RESET command does not work during this condition. To exit the unlock bypass mode, the system must issue a two-cycle unlock bypass reset command sequence [see Command Definitions on page 67 for details]. November 8, 2007 S29GL-P_00_A7 S29GL-P MirrorBit(R) Flash Family 41 Data 8. Sheet (Pre limin ar y) Advanced Sector Protection/Unprotection The Advanced Sector Protection/Unprotection feature disables or enables programming or erase operations in any or all sectors and can be implemented through software and/or hardware methods, which are independent of each other. This section describes the various methods of protecting data stored in the memory array. An overview of these methods in shown in Figure 8.1. Figure 8.1 Advanced Sector Protection/Unprotection Hardware Methods Software Methods Lock Register (One Time Programmable) WP#/ACC = VIL (Highest or Lowest Sector Locked) Password Method Persistent Method (DQ2) (DQ1) 64-bit Password (One Time Protect) PPB Lock Bit1,2,3 0 = PPBs Locked Memory Array Persistent Protection Bit (PPB)4,5 Sector 0 PPB 0 DYB 0 Sector 1 PPB 1 DYB 1 Sector 2 PPB 2 DYB 2 Sector N-2 PPB N-2 DYB N-2 Sector N-1 PPB N-1 DYB N-1 PPB N DYB N 3 Sector N 3. N = Highest Address Sector. 42 1 = PPBs Unlocked 1. Bit is volatile, and defaults to "1" on reset. 2. Programming to "0" locks all PPBs to their current state. 3. Once programmed to "0", requires hardware reset to unlock. 4. 0 = Sector Protected, 1 = Sector Unprotected. 5. PPBs programmed individually, but cleared collectively S29GL-P MirrorBit(R) Flash Family Dynamic Protection Bit (DYB)6,7,8 6. 0 = Sector Protected, 1 = Sector Unprotected. 7. Protect effective only if PPB Lock Bit is unlocked and corresponding PPB is "1" (unprotected). 8. Volatile Bits: defaults to user choice upon power-up (see ordering options). S29GL-P_00_A7 November 8, 2007 Da ta 8.1 Shee t (Prelimi nar y) Lock Register As shipped from the factory, all devices default to the persistent mode when power is applied, and all sectors are unprotected, unless otherwise chosen through the DYB ordering option (see Ordering Information on page 9). The device programmer or host system must then choose which sector protection method to use. Programming (setting to "0") any one of the following two one-time programmable, non-volatile bits locks the part permanently in that mode: Lock Register Persistent Protection Mode Lock Bit (DQ1) Lock Register Password Protection Mode Lock Bit (DQ2) Table 8.1 Lock Register DQ15-3 DQ2 DQ1 DQ0 Don't Care Password Protection Mode Lock Bit Persistent Protection Mode Lock Bit Secured Silicon Sector Protection Bit For programming lock register bits refer to Table 12.2 on page 69 and Table 12.4 on page 71. Notes 1. If the password mode is chosen, the password must be programmed before setting the corresponding lock register bit. 2. After the Lock Register Bits Command Set Entry command sequence is written, reads and writes for Sector 0 are disabled, while reads from other sectors are allowed until exiting this mode. 3. If both lock bits are selected to be programmed (to zeros) at the same time, the operation aborts. 4. Once the Password Mode Lock Bit is programmed, the Persistent Mode Lock Bit is permanently disabled, and no changes to the protection scheme are allowed. Similarly, if the Persistent Mode Lock Bit is programmed, the Password Mode is permanently disabled. After selecting a sector protection method, each sector can operate in any of the following three states: 1. Constantly locked. The selected sectors are protected and can not be reprogrammed unless PPB lock bit is cleared via a password, hardware reset, or power cycle. 2. Dynamically locked. The selected sectors are protected and can be altered via software commands. 3. Unlocked. The sectors are unprotected and can be erased and/or programmed. These states are controlled by the bit types described in Section 8.2-Section 8.5. 8.2 Persistent Protection Bits The Persistent Protection Bits are unique and nonvolatile for each sector and have the same endurances as the Flash memory. Preprogramming and verification prior to erasure are handled by the device, and therefore do not require system monitoring. Notes 1. Each PPB is individually programmed and all are erased in parallel. 2. While programming PPB for a sector, array data can be read from any other sector, except Sector 0 (used for Data# Polling) and the sector in which sector PPB is being programmed. 3. Entry command disables reads and writes for the sector selected. 4. Reads within that sector return the PPB status for that sector. 5. All Reads must be performed using the read mode. 6. The specific sector address (A25-A16 GL01GP, A24-A16 GL512P, A23-A16 GL256P, A22-A16 GL128P) are written at the same time as the program command. 7. If the PPB Lock Bit is set, the PPB Program or erase command does not execute and times-out without programming or erasing the PPB. November 8, 2007 S29GL-P_00_A7 S29GL-P MirrorBit(R) Flash Family 43 Data Sheet (Pre limin ar y) 8. There are no means for individually erasing a specific PPB and no specific sector address is required for this operation. 9. Exit command must be issued after the execution which resets the device to read mode and reenables reads and writes for Sector 0. 10. The programming state of the PPB for a given sector can be verified by writing a PPB Status Read Command to the device as described by the flow chart shown in Figure 8.2. Figure 8.2 PPB Program Algorithm Enter PPB Command Set. Addr = BA Program PPB Bit. Addr = SA Read Byte Twice Addr = SA0 No DQ6 = Toggle? Yes No DQ5 = 1? Wait 500 s Yes Read Byte Twice Addr = SA0 DQ6 = Toggle? No Read Byte. Addr = SA Yes No DQ0 = '0' (Pgm.)? FAIL Yes Issue Reset Command PASS Exit PPB Command Set 44 S29GL-P MirrorBit(R) Flash Family S29GL-P_00_A7 November 8, 2007 Da ta 8.2.1 Shee t (Prelimi nar y) Dynamic Protection Bits Dynamic Protection Bits are volatile and unique for each sector and can be individually modified. DYBs only control the protection scheme for unprotected sectors that have their PPBs cleared (erased to "1"). By issuing the DYB Set or Clear command sequences, the DYBs are set (programmed to "0") or cleared (erased to "1"), thus placing each sector in the protected or unprotected state respectively. This feature allows software to easily protect sectors against inadvertent changes yet does not prevent the easy removal of protection when changes are needed. Notes 1. The DYBs can be set (programmed to "0") or cleared (erased to "1") as often as needed. When the parts are first shipped, the PPBs are cleared (erased to "1") and upon power up or reset, the DYBs can be set or cleared depending upon the ordering option chosen. 2. If the option to clear the DYBs after power up is chosen, (erased to "1"), then the sectorsmay be modified depending upon the PPB state of that sector (see Table 8.2). 3. The sectors would be in the protected state If the option to set the DYBs after power up is chosen (programmed to "0"). 4. It is possible to have sectors that are persistently locked with sectors that are left in the dynamic state. 5. The DYB Set or Clear commands for the dynamic sectors signify protected or unprotectedstate of the sectors respectively. However, if there is a need to change the status of the persistently locked sectors, a few more steps are required. First, the PPB Lock Bit must be cleared by either putting the device through a power-cycle, or hardware reset. The PPBs can then be changed to reflect the desired settings. Setting the PPB Lock Bit once again locks the PPBs, and the device operates normally again. 6. To achieve the best protection, it is recommended to execute the PPB Lock Bit Set command early in the boot code and protect the boot code by holding WP#/ACC = VIL. Note that the PPB and DYB bits have the same function when WP#/ACC = VHH as they do when ACC =VIH. 8.3 Persistent Protection Bit Lock Bit The Persistent Protection Bit Lock Bit is a global volatile bit for all sectors. When set (programmed to "0"), it locks all PPBs and when cleared (programmed to "1"), allows the PPBs to be changed. There is only one PPB Lock Bit per device. Notes 1. No software command sequence unlocks this bit unless the device is in the password protection mode; only a hardware reset or a power-up clears this bit. 2. The PPB Lock Bit must be set (programmed to "0") only after all PPBs are configured to the desired settings. 8.4 Password Protection Method The Password Protection Method allows an even higher level of security than the Persistent Sector Protection Mode by requiring a 64-bit password for unlocking the device PPB Lock Bit. In addition to this password requirement, after power up and reset, the PPB Lock Bit is set "0" to maintain the password mode of operation. Successful execution of the Password Unlock command by entering the entire password clears the PPB Lock Bit, allowing for sector PPBs modifications. Notes 1. There is no special addressing order required for programming the password. Once the Password is written and verified, the Password Mode Locking Bit must be set in order to prevent access. 2. The Password Program Command is only capable of programming "0"s. Programming a "1" after a cell is programmed as a "0" results in a time-out with the cell as a "0". 3. The password is all "1"s when shipped from the factory. 4. All 64-bit password combinations are valid as a password. November 8, 2007 S29GL-P_00_A7 S29GL-P MirrorBit(R) Flash Family 45 Data Sheet (Pre limin ar y) 5. There is no means to verify what the password is after it is set. 6. The Password Mode Lock Bit, once set, prevents reading the 64-bit password on the data bus and further password programming. 7. The Password Mode Lock Bit is not erasable. 8. The lower two address bits (A1-A0) are valid during the Password Read, Password Program, and Password Unlock. 9. The exact password must be entered in order for the unlocking function to occur. 10. The Password Unlock command cannot be issued any faster than 1 s at a time to prevent a hacker from running through all the 64-bit combinations in an attempt to correctly match a password. 11. Approximately 1 s is required for unlocking the device after the valid 64-bit password is given to the device. 12. Password verification is only allowed during the password programming operation. 13. All further commands to the password region are disabled and all operations are ignored. 14. If the password is lost after setting the Password Mode Lock Bit, there is no way to clear the PPB Lock Bit. 15. Entry command sequence must be issued prior to any of any operation and it disables reads and writes for Sector 0. Reads and writes for other sectors excluding Sector 0 are allowed. 16. If the user attempts to program or erase a protected sector, the device ignores the command and returns to read mode. 17. A program or erase command to a protected sector enables status polling and returns to read mode without having modified the contents of the protected sector. 18. The programming of the DYB, PPB, and PPB Lock for a given sector can be verified by writing individual status read commands DYB Status, PPB Status, and PPB Lock Status to the device. 46 S29GL-P MirrorBit(R) Flash Family S29GL-P_00_A7 November 8, 2007 Da ta Shee t (Prelimi nar y) Figure 8.3 Lock Register Program Algorithm Write Unlock Cycles: Address 555h, Data AAh Address 2AAh, Data 55h Unlock Cycle 1 Unlock Cycle 2 Write Enter Lock Register Command: Address 555h, Data 40h XXXh = Address don't care Program Lock Register Data Address XXXh, Data A0h Address XXXh*, Data PD Program Data (PD): See text for Lock Register definitions Caution: Lock register can only be progammed once. Perform Polling Algorithm (see Write Operation Status flowchart) Yes Done? No DQ5 = 1? No Error condition (Exceeded Timing Limits) Yes PASS. Write Lock Register Exit Command: Address XXXh, Data 90h Address XXXh, Data 00h Device returns to reading array. November 8, 2007 S29GL-P_00_A7 FAIL. Write rest command to return to reading array. S29GL-P MirrorBit(R) Flash Family 47 Data 8.5 Sheet (Pre limin ar y) Advanced Sector Protection Software Examples Table 8.2 Sector Protection Schemes: DYB, PPB and PPB Lock Bit Combinations Unique Device PPB Lock Bit 0 = locked 1 = unlocked Any Sector Sector PPB 0 = protected 1 = unprotected Sector DYB 0 = protected 1 = unprotected Sector Protection Status 0 x Protected through PPB 0 Any Sector 0 0 x Protected through PPB Any Sector 0 1 1 Unprotected Any Sector 0 1 0 Protected through DYB Any Sector 1 0 x Protected through PPB Any Sector 1 0 x Protected through PPB Any Sector 1 1 0 Protected through DYB Any Sector 1 1 1 Unprotected Table 8.2 contains all possible combinations of the DYB, PPB, and PPB Lock Bit relating to the status of the sector. In summary, if the PPB Lock Bit is locked (set to "0"), no changes to the PPBs are allowed. The PPB Lock Bit can only be unlocked (reset to "1") through a hardware reset or power cycle. See also Figure 8.1 for an overview of the Advanced Sector Protection feature. 8.6 Hardware Data Protection Methods The device offers two main types of data protection at the sector level via hardware control: When WP#/ACC is at VIL, the either the highest or lowest sector is locked (device specific). There are additional methods by which intended or accidental erasure of any sectors can be prevented via hardware means. The following subsections describes these methods: 8.6.1 WP#/ACC Method The Write Protect feature provides a hardware method of protecting one outermost sector. This function is provided by the WP#/ACC pin and overrides the previously discussed Sector Protection/Unprotection method. If the system asserts VIL on the WP#/ACC pin, the device disables program and erase functions in the highest or lowest sector independently of whether the sector was protected or unprotected using the method described in Advanced Sector Protection/Unprotection on page 42. If the system asserts VIH on the WP#/ACC pin, the device reverts to whether the boot sectors were last set to be protected or unprotected. That is, sector protection or unprotection for these sectors depends on whether they were last protected or unprotected. The WP#/ACC pin must be held stable during a command sequence execution. WP# has an internal pull-up; when unconnected, WP# is set at VIH. Note If WP#/ACC is at VIL when the device is in the standby mode, the maximum input load current is increased. See Table 11.6 on page 55 for details. 8.6.2 Low VCC Write Inhibit When VCC is less than VLKO, the device does not accept any write cycles. This protects data during VCC power-up and power-down. The command register and all internal program/erase circuits are disabled, and the device resets to reading array data. Subsequent writes are ignored until VCC is greater than VLKO. The system must provide the proper signals to the control inputs to prevent unintentional writes when VCC is greater than VLKO. 48 S29GL-P MirrorBit(R) Flash Family S29GL-P_00_A7 November 8, 2007 Da ta 8.6.3 Shee t (Prelimi nar y) Write Pulse "Glitch Protection" Noise pulses of less than 5 ns (typical) on OE#, CE# or WE# do not initiate a write cycle. 8.6.4 Power-Up Write Inhibit If WE# = CE# = RESET# = VIL and OE# = VIH during power up, the device does not accept commands on the rising edge of WE#. The internal state machine is automatically reset to the read mode on power-up. 9. Power Conservation Modes 9.1 Standby Mode When the system is not reading or writing to the device, it can place the device in the standby mode. In this mode, current consumption is greatly reduced, and the outputs are placed in the high impedance state, independent of the OE# input. The device enters the CMOS standby mode when the CE# and RESET# inputs are both held at VCC 0.3 V. The device requires standard access time (tCE) for read access, before it is ready to read data. If the device is deselected during erasure or programming, the device draws active current until the operation is completed. ICC4 in "DC Characteristics" represents the standby current specification 9.2 Automatic Sleep Mode The automatic sleep mode minimizes Flash device energy consumption. The device automatically enables this mode when addresses remain stable for tACC + 30 ns. The automatic sleep mode is independent of the CE#, WE#, and OE# control signals. Standard address access timings provide new data when addresses are changed. While in sleep mode, output data is latched and always available to the system. ICC6 in Section 11.6 represents the automatic sleep mode current specification. 9.3 Hardware RESET# Input Operation The RESET# input provides a hardware method of resetting the device to reading array data. When RESET# is driven low for at least a period of tRP, the device immediately terminates any operation in progress, tristates all outputs, and ignores all read/write commands for the duration of the RESET# pulse. The device also resets the internal state machine to reading array data. The operation that was interrupted should be reinitiated once the device is ready to accept another command sequence to ensure data integrity. When RESET# is held at VSS 0.3 V, the device draws ICC reset current (ICC5). If RESET# is held at VIL but not within VSS 0.3 V, the standby current is greater. RESET# may be tied to the system reset circuitry and thus, a system reset would also reset the Flash memory, enabling the system to read the boot-up firmware from the Flash memory. 9.4 Output Disable (OE#) When the OE# input is at VIH, output from the device is disabled. The outputs are placed in the high impedance state. (With the exception of RY/BY#.) November 8, 2007 S29GL-P_00_A7 S29GL-P MirrorBit(R) Flash Family 49 Data Sheet (Pre limin ar y) 10. Secured Silicon Sector Flash Memory Region The Secured Silicon Sector provides an extra Flash memory region that enables permanent part identification through an Electronic Serial Number (ESN). The Secured Silicon Sector is 128 words in length and all Secured Silicon reads outside of the 128-word address range returns invalid data. The Secured Silicon Sector Indicator Bit, DQ7, (at Autoselect address 03h) is used to indicate whether or not the Secured Silicon Sector is locked when shipped from the factory. Please note the following general conditions: On power-up, or following a hardware reset, the device reverts to sending commands to the normal address space. Reads outside of sector SA0 return memory array data. Sector SA0 is remapped from memory array to Secured Silicon Sector array. Once the Secured Silicon Sector Entry Command is issued, the Secured Silicon Sector Exit command must be issued to exit Secured Silicon Sector Mode. The Secured Silicon Sector is not accessible when the device is executing an Embedded Program or Embedded Erase algorithm. The ACC function and unlock bypass modes are not available when the Secured Silicon Sector is enabled. Table 10.1 Secured Silicon Sector Addresses Secured Silicon Sector Address Range 000000h-000007h 000008h-00007Fh 10.1 Customer Lockable ESN Factory Locked ExpressFlash Factory Locked Determined by customer ESN ESN or determined by customer Unavailable Determined by customer Factory Locked Secured Silicon Sector The Factory Locked Secured Silicon Sector is always protected when shipped from the factory and has the Secured Silicon Sector Indicator Bit (DQ7) permanently set to a "1". This prevents cloning of a factory locked part and ensures the security of the ESN and customer code once the product is shipped to the field. These devices are available pre-programmed with one of the following: A random, 8 Word secure ESN only within the Secured Silicon Sector (at addresses 000000H - 000007H) Both a random, secure ESN and customer code through the Spansion programming service. Customers may opt to have their code programmed through the Spansion programming services. Spansion programs the customer's code, with or without the random ESN. The devices are then shipped from the Spansion factory with the Secured Silicon Sector permanently locked. Contact your local representative for details on using Spansion programming services. 10.2 Customer Lockable Secured Silicon Sector The Customer Lockable Secured Silicon Sector is always shipped unprotected (DQ7 set to "0"), allowing customers to utilize that sector in any manner they choose. If the security feature is not required, the Secured Silicon Sector can be treated as an additional Flash memory space. Please note the following: Once the Secured Silicon Sector area is protected, the Secured Silicon Sector Indicator Bit is permanently set to "0." The Secured Silicon Sector can be read any number of times, but can be programmed and locked only once. The Secured Silicon Sector lock must be used with caution as once locked, there is no procedure available for unlocking the Secured Silicon Sector area and none of the bits in the Secured Silicon Sector memory space can be modified in any way. The accelerated programming (ACC) and unlock bypass functions are not available when the Secured Silicon Sector is enabled. 50 S29GL-P MirrorBit(R) Flash Family S29GL-P_00_A7 November 8, 2007 Da ta Shee t (Prelimi nar y) Once the Secured Silicon Sector is locked and verified, the system must write the Exit Secured Silicon Sector Region command sequence which return the device to the memory array at sector 0. 10.3 Secured Silicon Sector Entry/Exit Command Sequences The system can access the Secured Silicon Sector region by issuing the three-cycle Enter Secured Silicon Sector command sequence. The device continues to access the Secured Silicon Sector region until the system issues the four-cycle Exit Secured Silicon Sector command sequence. See Command Definitions on page 67 [Secured Silicon Sector Command Table, Appendix Table 12.1 on page 68 through Table 12.4 on page 71 for address and data requirements for both command sequences. The Secured Silicon Sector Entry Command allows the following commands to be executed Read customer and factory Secured Silicon areas Program the customer Secured Silicon Sector After the system has written the Enter Secured Silicon Sector command sequence, it may read the Secured Silicon Sector by using the addresses normally occupied by sector SA0 within the memory array. This mode of operation continues until the system issues the Exit Secured Silicon Sector command sequence, or until power is removed from the device. Software Functions and Sample Code The following are C functions and source code examples of using the Secured Silicon Sector Entry, Program, and exit commands. Refer to the Spansion Low Level Driver User's Guide (available soon on www.spansion.com) for general information on Spansion Flash memory software development guidelines. Table 10.2 Secured Silicon Sector Entry (LLD Function = lld_SecSiSectorEntryCmd) Cycle Operation Byte Address Word Address Data Unlock Cycle 1 Write Base + AAAh Base + 555h 00AAh Unlock Cycle 2 Write Base + 555h Base + 2AAh 0055h Entry Cycle Write Base + AAAh Base + 555h 0088h Note Base = Base Address. /* Example: SecSi Sector *( (UINT16 *)base_addr *( (UINT16 *)base_addr *( (UINT16 *)base_addr Entry Command */ + 0x555 ) = 0x00AA; + 0x2AA ) = 0x0055; + 0x555 ) = 0x0088; /* write unlock cycle 1 /* write unlock cycle 2 /* write Secsi Sector Entry Cmd */ */ */ Table 10.3 Secured Silicon Sector Program (LLD Function = lld_ProgramCmd) Cycle Operation Byte Address Word Address Data Unlock Cycle 1 Write Base + AAAh Base + 555h 00AAh Unlock Cycle 2 Write Base + 555h Base + 2AAh 0055h Program Setup Write Base + AAAh Base + 555h 00A0h Program Write Word Address Word Address Data Word Note Base = Base Address. /* Once in the SecSi Sector mode, you program */ /* words using the programming algorithm. */ November 8, 2007 S29GL-P_00_A7 S29GL-P MirrorBit(R) Flash Family 51 Data Sheet (Pre limin ar y) Table 10.4 Secured Silicon Sector Exit (LLD Function = lld_SecSiSectorExitCmd) Cycle Operation Byte Address Word Address Data Unlock Cycle 1 Write Unlock Cycle 2 Write Base + AAAh Base + 555h 00AAh Base + 555h Base + 2AAh 0055h Exit Cycle 3 Exit Cycle 4 Write Base + AAAh Base + 555h 0090h Write Base + AAAh Base + 000h 0000h Note Base = Base Address. /* Example: SecSi Sector *( (UINT16 *)base_addr *( (UINT16 *)base_addr *( (UINT16 *)base_addr *( (UINT16 *)base_addr Exit Command */ + 0x555 ) = 0x00AA; + 0x2AA ) = 0x0055; + 0x555 ) = 0x0090; + 0x000 ) = 0x0000; /* /* /* /* write write write write unlock cycle unlock cycle SecSi Sector SecSi Sector 1 2 Exit cycle 3 Exit cycle 4 */ */ */ */ 11. Electrical Specifications 11.1 Absolute Maximum Ratings Description Rating Storage Temperature, Plastic Packages -65C to +150C Ambient Temperature with Power Applied -65C to +125C All Inputs and I/Os except as noted below (Note 1) VCC (Note 1) Voltage with Respect to Ground -0.5 V to VCC + 0.5 V -0.5 V to +4.0 V -0.5V to +4.0V VIO A9 and ACC (Note 2) -0.5 V to +12.5 V Output Short Circuit Current (Note 3) 200 mA Notes 1. Minimum DC voltage on input or I/Os is -0.5 V. During voltage transitions, inputs or I/Os may undershoot VSS to -2.0 V for periods of up to 20 ns. See Figure 11.1. Maximum DC voltage on input or I/Os is VCC + 0.5 V. During voltage transitions inputs or I/Os may overshoot to VCC + 2.0 V for periods up to 20 ns. See Figure 11.2. 2. Minimum DC input voltage on pins A9 and ACC is -0.5V. During voltage transitions, A9 and ACC may overshoot VSS to -2.0 V for periods of up to 20 ns. See Figure 11.1. Maximum DC voltage on pins A9 and ACC is +12.5 V, which may overshoot to 14.0 V for periods up to 20 ns. 3. No more than one output may be shorted to ground at a time. Duration of the short circuit should not be greater than one second. 4. Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational sections of this data sheet is not implied. Exposure of the device to absolute maximum rating conditions for extended periods may affect device reliability. Figure 11.1 Maximum Negative Overshoot Waveform 20 ns 20 ns +0 .8 V -0 .5 V -2 .0 V 20 n s 52 S29GL-P MirrorBit(R) Flash Family S29GL-P_00_A7 November 8, 2007 Da ta Shee t (Prelimi nar y) Figure 11.2 Maximum Positive Overshoot Waveform 20 ns VCC +2.0 V VCC +0.5 V +2.0 V 20 ns 11.2 20 ns Operating Ranges Specifications Range Ambient Temperature (TA), Industrial (I) Device -40C to +85C Supply Voltages VCC +2.7 V to 3.6 V or +3.0 V to 3.6 V VIO Supply Voltages VIO +1.65 V to VCC Notes 1. Operating ranges define those limits between which the functionality of the device is guaranteed. 2. See also Ordering Information on page 9. 3. For valid VCC/VIO range combinations, see Ordering Information on page 9. The I/Os do not operate at 3 V when VIO = 1.8 V. 11.3 Test Conditions Figure 11.3 Test Setup Device Under Test CL November 8, 2007 S29GL-P_00_A7 S29GL-P MirrorBit(R) Flash Family 53 Data Sheet (Pre limin ar y) Table 11.1 Test Specifications Test Condition All Speeds Output Load Unit 1 TTL gate Output Load Capacitance, CL (including jig capacitance) 30 pF Input Rise and Fall Times 5 ns Input Pulse Levels 0.0-VIO V Input timing measurement reference levels (See Note) 0.5VIO V Output timing measurement reference levels 0.5 VIO V Note If VIO < VCC, the reference level is 0.5 VIO. 11.4 Key to Switching Waveforms Waveform Inputs Outputs Steady Changing from H to L Changing from L to H 11.5 Don't Care, Any Change Permitted Changing, State Unknown Does Not Apply Center Line is High Impedance State (High Z) Switching Waveforms Figure 11.4 Input Waveforms and Measurement Levels VIO 0.0 V Input 0.5 VIO Measurement Level 0.5 VIO Output Note If VIO < VCC, the input measurement reference level is 0.5 VIO. 54 S29GL-P MirrorBit(R) Flash Family S29GL-P_00_A7 November 8, 2007 Da ta 11.6 Shee t (Prelimi nar y) DC Characteristics Table 11.2 S29GL-P DC Characteristics (CMOS Compatible) Parameter Symbol Parameter Description (Notes) Test Conditions Min Typ Max Unit WP/ACC 2.0 A Others 1.0 ILI Input Load Current (1) VIN = VSS to VCC VCC = VCC max ILIT A9 Input Load Current VCC = VCC max; A9 = 12.5 V ILO Output Leakage Current VOUT = VSS to VCC , VCC = VCC max CE# = VIL, OE# = VIH, VCC = VCCmax, f = 1 MHz 6 20 ICC1 VCC Active Read Current (1) CE# = VIL, OE# = VIH, VCC = VCCmax, f = 5 MHz 30 55 CE# = VIL, OE# = VIH, VCC = VCCmax, f = 10 MHz 60 110 IIO2 VIO Non-Active Output CE# = VIL, OE# = VIH 0.2 10 ICC2 VCC Intra-Page Read Current (1) ICC3 ICC4 35 A 1.0 A mA mA CE# = VIL, OE# = VIH, VCC = VCCmax, f = 10 MHz 1 10 CE# = VIL, OE# = VIH, VCC = VCCmax, f = 33 MHz 5 20 VCC Active Erase/ Program Current (2, 3) CE# = VIL, OE# = VIH, VCC = VCCmax 50 90 mA VCC Standby Current CE#, RESET# = VCC 0.3 V, OE# = VIH, VCC = VCCmax 1 5 A 250 500 A 1 5 A WP#/ACC pin 10 20 VCC pin 50 80 mA VIL = VSS + 0.3 V/-0.1V, ICC5 VCC Reset Current ICC6 Automatic Sleep Mode (4) IACC ACC Accelerated Program Current VCC = VCCmax; VIL = VSS + 0.3 V/-0.1V, RESET# = VSS 0.3 V VCC = VCCmax, VIH = VCC 0.3 V, VIL = VSS + 0.3 V/-0.1V, WP#/ACC = VIH CE# = VIL, OE# = VIH, VCC = VCCmax, WP#/ACC = VHH mA VIL Input Low Voltage (5) -0.1 0.3 x VIO V VIH Input High Voltage (5) 0.7 x VIO VIO + 0.3 V VHH Voltage for Program Acceleration VCC = 2.7 -3.6 V 11.5 12.5 V VID Voltage for Autoselect and Temporary Sector Unprotect VCC = 2.7 -3.6 V 11.5 12.5 V 0.15 x VIO V VOL Output Low Voltage (5) IOL = 100 A VOH Output High Voltage (5) IOH = -100 A VLKO Low VCC Lock-Out Voltage (3) 0.85 x VIO 2.3 V 2.5 V Notes 1. The ICC current listed is typically less than 2 mA/MHz, with OE# at VIH. 2. ICC active while Embedded Erase or Embedded Program or Write Buffer Programming is in progress. 3. Not 100% tested. 4. Automatic sleep mode enables the lower power mode when addresses remain stable tor tACC + 30 ns. 5. VIO = 1.65-3.6 V 6. VCC = 3 V and VIO = 3V or 1.8V. When VIO is at 1.8V, I/O pins cannot operate at 3V. November 8, 2007 S29GL-P_00_A7 S29GL-P MirrorBit(R) Flash Family 55 Data 11.7 Sheet (Pre limin ar y) AC Characteristics 11.7.1 S29GL-P Read-Only Operations Table 11.3 S29GL-P Read-Only Operations Parameter JEDEC Std. Speed Options Description (Notes) Test Setup 90 100 110 120 130 - 100 110 120 - - - 110 120 130 VIO = VCC = 3.0 V 90 100 110 - - VIO = VCC = 2.7 V - 100 110 120 - - - 110 120 130 VIO = VCC = 3.0 V 90 100 110 - - VIO = VCC = 2.7 V - 100 110 120 - - - 110 120 130 90 100 110 - - VIO = VCC = 2.7 V tAVAV tAVQV tELQV tRC tACC tCE VIO = 1.65 V to VCC, VCC = 3 V Read Cycle Time VIO = 1.65 V to VCC, VCC = 3 V Address to Output Delay (1) VIO = 1.65 V to VCC, VCC = 3 V Chip Enable to Output Delay (2) Min Max Max VIO = VCC = 3.0 V tPACC Unit ns ns ns Page Access Time Max 25 ns tGLQV tOE Output Enable to Output Delay Max 25 ns tEHQZ tDF Chip Enable to Output High Z (3) Max 20 ns tGHQZ tDF Output Enable to Output High Z (3) Max 20 ns tOH Output Hold Time From Addresses, CE# or OE#, Whichever Occurs First Min 0 ns Output Enable Hold Time (3) Read Min 0 ns tOEH Toggle and Data# Polling Min 10 ns tCEH Chip Enable Hold Time Read Min 35 ns tAXQX Notes 1. CE#, OE# = VIL 2. OE# = VIL 3. Not 100% tested. 4. See Figure 11.3 and Table 11.1 for test specifications. 5. Unless otherwise indicated, AC specifications for 110 ns speed options are tested with VIO = VCC = 2.7 V. AC specifications for 110 ns speed options are tested with VIO = 1.8 V and VCC = 3.0 V. 56 S29GL-P MirrorBit(R) Flash Family S29GL-P_00_A7 November 8, 2007 Da ta Shee t (Prelimi nar y) Figure 11.5 Read Operation Timings tRC Addresses Stable Addresses tACC CE# tCEH tRH tRH tDF tOE OE# tOEH WE# tCE tOH HIGH Z HIGH Z Output Valid Outputs RESET# RY/BY# 0V Figure 11.6 Page Read Timings Same Page Amax:A3 A2:A0 (See Note) Aa tACC Data Bus Ab tPACC Qa Ad Ac tPACC Qb tPACC Qc Qd CE# OE# Note Figure 11.6 shows word mode. Addresses are A2:A-1 for byte mode. November 8, 2007 S29GL-P_00_A7 S29GL-P MirrorBit(R) Flash Family 57 Data 11.7.2 Sheet (Pre limin ar y) Hardware Reset (RESET#) Table 11.4 Hardware Reset (RESET#) Parameter JEDEC Std. Description Speed Unit tReady RESET# Pin Low (During Embedded Algorithms) to Read Mode or Write mode Min 35 s tReady RESET# Pin Low (NOT During Embedded Algorithms) to Read Mode or Write mode Min 35 s tRP RESET# Pulse Width Min 35 s tRH Reset High Time Before Read Min 200 ns tRPD RESET# Low to Standby Mode Min 10 s tRB RY/BY# Recovery Time Min 0 ns Figure 11.7 Reset Timings RY/BY# CE#, OE# tRH RESET# tRP tReady Reset Timings NOT during Embedded Algorithms Reset Timings during Embedded Algorithms tReady RY/BY# tRB CE#, OE# RESET# tRP 58 S29GL-P MirrorBit(R) Flash Family S29GL-P_00_A7 November 8, 2007 Da ta Shee t (Prelimi nar y) Table 11.5 Power-up Sequence Timings Parameter Description Speed Unit Min 35 s Reset Low Time from rising edge of VIO (or last Reset pulse) to rising edge of RESET# Min 35 s Reset High Time before Read Min 200 ns tVCS Reset Low Time from rising edge of VCC (or last Reset pulse) to rising edge of RESET# tVIOS tRH Notes 1. VIO < VCC + 200 mV. 2. VIO and VCC ramp must be synchronized during power up. 3. If RESET# is not stable for tVCS or tVIOS: The device does not permit any read and write operations. A valid read operation returns FFh. A hardware reset is required. 4. VCC maximum power-up current (RST=VIL) is 20 mA. Figure 11.8 Power-up Sequence Timings VCC VCC min VIO VIO min tRH CE# RESET# November 8, 2007 S29GL-P_00_A7 tVIOS tVCS S29GL-P MirrorBit(R) Flash Family 59 Data 11.7.3 Sheet (Pre limin ar y) S29GL-P Erase and Program Operations Table 11.6 S29GL-P Erase and Program Operations Parameter Speed Options JEDEC Std. Description tAVAV tWC Write Cycle Time (Note 1) Min 90 100 110 120 130 90 100 110 120 130 Unit tAVWL tAS Address Setup Time Min 0 ns tASO Address Setup Time to OE# low during toggle bit polling Min 15 ns ns ns tAH Address Hold Time Min 45 tAHT Address Hold Time From CE# or OE# high during toggle bit polling Min 0 ns tDVWH tDS Data Setup Time Min 30 ns tWHDX tDH Data Hold Time Min 0 ns ns tWLAX tCEPH CE# High during toggle bit polling Min 20 tOEPH Output Enable High during toggle bit polling Min 20 ns tGHWL tGHWL Read Recovery Time Before Write (OE# High to WE# Low) Min 0 ns tELWL tCS CE# Setup Time Min 0 ns ns tWHEH tCH CE# Hold Time Min 0 tWLWH tWP Write Pulse Width Min 35 ns tWHDL tWPH Write Pulse Width High Min 30 ns Write Buffer Program Operation (Notes 2, 3) Typ 480 s tWHWH1 tWHWH2 tWHWH1 Effective Write Buffer Program Operation (Notes 2, 4) Per Word Typ 15 s Accelerated Effective Write Buffer Program Operation (Notes 2, 4) Per Word Typ 13.5 s Program Operation (Note 2) Word Typ 60 s Accelerated Programming Operation (Note 2) Word tWHWH2 Sector Erase Operation (Note 2) Typ 54 s Typ 0.5 sec tVHH VHH Rise and Fall Time (Note 1) Min 250 ns tVCS VCC Setup Time (Note 1) Min 35 s tBUSY Erase/Program Valid to RY/BY# Delay Max 90 ns tSEA Sector Erase Timeout Max 50 s Notes 1. Not 100% tested. 2. See Section 11.6 for more information. 3. For 1-32 words/1-64 bytes programmed. 4. Effective write buffer specification is based upon a 32-word/64-byte write buffer operation. 5. Unless otherwise indicated, AC specifications for 110 ns speed option are tested with VIO = VCC = 2.7 V. AC specifications for 110 ns speed options are tested with VIO = 1.8 V and VCC = 3.0 V. 60 S29GL-P MirrorBit(R) Flash Family S29GL-P_00_A7 November 8, 2007 Da ta Shee t (Prelimi nar y) Figure 11.9 Program Operation Timings Program Command Sequence (last two cycles) tAS tWC 555h Addresses Read Status Data (last two cycles) PA PA PA tAH CE# tCH OE# tWHWH1 tWP WE# tWPH tCS tDS tDH A0h Data PD Status tBUSY DOUT tRB RY/BY# VCC tVCS Notes 1. PA = program address, PD = program data, DOUT is the true data at the program address. 2. Illustration shows device in word mode. Figure 11.10 Accelerated Program Timing Diagram VHH ACC VIL or VIH VIL or VIH tVHH tVHH Notes 1. Not 100% tested. 2. CE#, OE# = VIL 3. OE# = VIL 4. See Figure 11.3 and Table 11.1 for test specifications. November 8, 2007 S29GL-P_00_A7 S29GL-P MirrorBit(R) Flash Family 61 Data Sheet (Pre limin ar y) Figure 11.11 Chip/Sector Erase Operation Timings Erase Command Sequence (last two cycles) tAS tWC 2AAh Addresses Read Status Data VA SA VA 555h for chip erase tAH CE# tCH OE# tWP WE# tWPH tCS tWHWH2 tDS tDH Data 55h In Progress 30h Complete 10 for Chip Erase tBUSY tRB RY/BY# tVCS VCC Notes 1. SA = sector address (for Sector Erase), VA = Valid Address for reading status data (see Write Operation Status on page 36.) 2. These waveforms are for the word mode Figure 11.12 Data# Polling Timings (During Embedded Algorithms) tRC Addresses VA VA VA tACC tCE CE# tCH tOE OE# tOEH tDF WE# tOH High Z DQ7 Complement Complement Status Data Status Data True Valid Data High Z DQ6-DQ0 True Valid Data tBUSY RY/BY# Notes 1. VA = Valid address. Illustration shows first status cycle after command sequence, last status read cycle, and array data read cycle. 2. tOE for data polling is 45 ns when VIO = 1.65 to 2.7 V and is 35 ns when VIO = 2.7 to 3.6 V 3. CE# does not need to go high between status bit reads 62 S29GL-P MirrorBit(R) Flash Family S29GL-P_00_A7 November 8, 2007 Da ta Shee t (Prelimi nar y) Figure 11.13 Toggle Bit Timings (During Embedded Algorithms) tAHT tAS Addresses tAHT tASO CE# tCEPH tOEH WE# tOEPH OE# tDH DQ2 and DQ6 tOE Valid Data Valid Status Valid Status Valid Status (first read) (second read) (stops toggling) Valid Data RY/BY# Note A = Valid address; not required for DQ6. Illustration shows first two status cycle after command sequence, last status read cycle, and array data read cycle CE# does not need to go high between status bit reads Figure 11.14 DQ2 vs. DQ6 Enter Embedded Erasing WE# Erase Suspend Erase Enter Erase Suspend Program Erase Suspend Read Erase Suspend Program Erase Resume Erase Suspend Read Erase Erase Complete DQ6 DQ2 Note DQ2 toggles only when read at an address within an erase-suspended sector. The system can use OE# or CE# to toggle DQ2 and DQ6. November 8, 2007 S29GL-P_00_A7 S29GL-P MirrorBit(R) Flash Family 63 Data 11.7.4 Sheet (Pre limin ar y) S29GL-P Alternate CE# Controlled Erase and Program Operations Table 11.7 S29GL-P Alternate CE# Controlled Erase and Program Operations Parameter Speed Options JEDEC Std. Description (Notes) tAVAV tWC Write Cycle Time (Note 1) Min tAVWL tAS Address Setup Time Min tELAX tDVEH tEHDX tGHEL 90 100 110 120 130 Unit 90 100 110 120 130 ns 0 ns tASO Address Setup Time to OE# low during toggle bit polling Min 15 ns tAH Address Hold Time Min 45 ns tAHT Address Hold Time From CE# or OE# high during toggle bit polling Min 0 ns tDS Data Setup Time Min 30 ns tDH Data Hold Time Min 0 ns tCEPH CE# High during toggle bit polling Min 20 ns tOEPH OE# High during toggle bit polling Min 20 ns tGHEL Read Recovery Time Before Write (OE# High to WE# Low) Min 0 ns tWLEL tWS WE# Setup Time Min 0 ns tEHWH tWH WE# Hold Time Min 0 ns tELEH tCP CE# Pulse Width Min 35 ns tEHEL tCPH CE# Pulse Width High Min 30 ns tWHWH1 tWHWH1 tWHWH2 tWHWH2 Write Buffer Program Operation (Notes 2, 3) Typ 480 s Effective Write Buffer Program Operation (Notes 2, 4) Per Word Typ 15 s Effective Accelerated Write Buffer Program Operation (Notes 2, 4) Per Word Typ 13.5 s Program Operation (Note 2) Word Typ 60 s Accelerated Programming Operation (Note 2) Word Typ 54 s Typ 0.5 sec Sector Erase Operation (Note 2) Notes 1. Not 100% tested. 2. See AC Characteristics on page 56 for more information. 3. For 1-32 words/1-64 bytes programmed. 4. Effective write buffer specification is based upon a 32-word/64-byte write buffer operation. 5. Unless otherwise indicated, AC specifications are tested with VIO = 1.8 V and VCC = 3.0 V. 64 S29GL-P MirrorBit(R) Flash Family S29GL-P_00_A7 November 8, 2007 Da ta Shee t (Prelimi nar y) Figure 11.15 Alternate CE# Controlled Write (Erase/Program) Operation Timings 555 for program 2AA for erase PA for program SA for sector erase 555 for chip erase Data# Polling Addresses PA tWC tAS tAH tWH WE# tGHEL OE# tWHWH1 or 2 tCP CE# tWS tCPH tBUSY tDS tDH DQ7# Data tRH A0 for program 55 for erase DOUT PD for program 30 for sector erase 10 for chip erase RESET# RY/BY# Notes 1. Figure 11.15 indicates last two bus cycles of a program or erase operation. 2. PA = program address, SA = sector address, PD = program data. 3. DQ7# is the complement of the data written to the device. DOUT is the data written to the device. 4. Waveforms are for the word mode. November 8, 2007 S29GL-P_00_A7 S29GL-P MirrorBit(R) Flash Family 65 Data 11.7.5 Sheet (Pre limin ar y) Erase And Programming Performance Table 11.8 Erase And Programming Performance Typ (Note 1) Max (Note 2) Unit 0.5 3.5 sec S29GL128P 64 256 S29GL256P 128 512 Parameter Sector Erase Time Chip Erase Time S29GL512P 256 1024 S29GL01GP 512 2048 Total Write Buffer Time (Note 3) 480 s 432 s Chip Program Time (Note 4) S29GL128P 123 S29GL256P 246 S29GL512P 492 S29GL01GP 984 Excludes 00h programming prior to erasure (Note 5) sec Total Accelerated Write Buffer Programming Time (Note 3) Comments Excludes system level overhead (Note 6) sec Notes 1. Typical program and erase times assume the following conditions: 25C, 3.6 V VCC, 10,000 cycles, checkerboard pattern. 2. Under worst case conditions of -40C, VCC = 3.0 V, 100,000 cycles. 3. Effective write buffer specification is based upon a 32-word write buffer operation. 4. The typical chip programming time is considerably less than the maximum chip programming time listed, since most words program faster than the maximum program times listed. 5. In the pre-programming step of the Embedded Erase algorithm, all bits are programmed to 00h before erasure. 6. System-level overhead is the time required to execute the two- or four-bus-cycle sequence for the program command. See Tables 12.1-12.4. 11.7.6 TSOP Pin and BGA Package Capacitance Table 11.9 Package Capacitance Parameter Symbol Parameter Description Test Setup Typ Max Unit CIN Input Capacitance VIN = 0 6 10 pF COUT Output Capacitance VOUT = 0 10 12 pF CIN2 Control Pin Capacitance VIN = 0 8 10 pF RESET#, WP#/ACC Separated Control Pin VIN = 0 42 45 pF CE# Separated Control Pin VIN = 0 22 25 pF Notes 1. Sampled, not 100% tested. 2. Test conditions TA = 25C, f = 1.0 MHz. 66 S29GL-P MirrorBit(R) Flash Family S29GL-P_00_A7 November 8, 2007 Da ta Shee t (Prelimi nar y) 12. Appendix This section contains information relating to software control or interfacing with the Flash device. For additional information and assistance regarding software, see Section 5. For the latest information, explore the Spansion web site at www.spansion.com. 12.1 Command Definitions Writing specific address and data commands or sequences into the command register initiates device operations. Tables 12.1-12.4 define the valid register command sequences. Writing incorrect address and data values or writing them in the improper sequence can place the device in an unknown state. A reset command is then required to return the device to reading array data. November 8, 2007 S29GL-P_00_A7 S29GL-P MirrorBit(R) Flash Family 67 Data Sheet (Pre limin ar y) Command (Notes) Cycles Table 12.1 S29GL-P Memory Array Command Definitions, x16 Bus Cycles (Notes 1-5) First Second Addr Data 1 RA RD Reset (7) 1 XXX F0 Autoselect (8,9) Read (6) Addr Third Data Addr Fourth Data Addr Fifth Data Manufacturer ID 4 555 AA 2AA 55 555 90 X00 01 Device ID (8) 4 555 AA 2AA 55 555 90 X01 227E Sector Protect Verify (10) 4 555 AA 2AA 55 555 90 [SA]X02 (10) Secure Device Verify (11) 2AA 55 555 90 X03 (11) 555 AA 1 55 98 Program 4 555 AA 2AA 55 555 A0 PA PD Write to Buffer 3 555 AA 2AA 55 SA 25 SA WC Program Buffer to Flash (Confirm) 1 SA 29 Write-to-Buffer-Abort Reset (13) 3 555 AA 2AA 55 555 F0 555 20 Unlock Bypass 4 CFI Query (12) Enter 3 555 AA 2AA 55 Program (14) 2 XXX A0 PA PD Sector Erase (14) 2 XXX 80 SA 30 Chip Erase (14) 2 XXX 80 XXX 10 Reset (15) 00 Sixth Addr Data Addr Data X0E (8) X0F (8) WBL PD WBL PD 2 XXX 90 XXX Chip Erase 6 555 AA 2AA 55 555 80 555 AA 2AA 55 555 10 Sector Erase 6 555 AA 2AA 55 555 80 555 AA 2AA 55 SA 30 Erase Suspend/Program Suspend (16) 1 XXX B0 Erase Resume/Program Resume (17) 1 XXX 30 Secured Silicon Sector Entry 3 555 AA 2AA 55 555 88 Secured Silicon Sector Exit (18) 4 555 AA 2AA 55 555 90 XX 00 Legend X = Don't care RA = Address of the memory to be read. RD = Data read from location RA during read operation. PA = Address of the memory location to be programmed. Addresses latch on the falling edge of the WE# or CE# pulse, whichever happens later. Notes 1. See Table 7.1 on page 19 for description of bus operations. 2. All values are in hexadecimal. 3. All bus cycles are write cycles unless otherwise noted. 4. Data bits DQ15-DQ8 are don't cares for unlock and command cycles. 5. Address bits AMAX:A16 are don't cares for unlock and command cycles, unless SA or PA required. (AMAX is the Highest Address pin.). 6. No unlock or command cycles required when reading array data. 7. The Reset command is required to return to reading array data when device is in the autoselect mode, or if DQ5 goes high (while the device is providing status data). 8. See Table 7.2 on page 22 for device ID values and definitions. 9. The fourth, fifth, and sixth cycles of the autoselect command sequence are read cycles. 10. The data is 00h for an unprotected sector and 01h for a protected sector. See Autoselect on page 21 for more information. This is same as PPB Status Read except that the protect and unprotect statuses are inverted here. PD = Data to be programmed at location PA. Data latches on the rising edge of the WE# or CE# pulse, whichever happens first. SA = Address of the sector to be verified (in autoselect mode) or erased. Address bits Amax-A16 uniquely select any sector. WBL = Write Buffer Location. The address must be within the same write buffer page as PA. WC = Word Count is the number of write buffer locations to load minus 1. 11. The data value for DQ7 is "1" for a serialized, protected Secured Silicon Sector region and "0" for an unserialized, unprotected region. See Table 7.3 on page 22 for data and definitions. 12. Command is valid when device is ready to read array data or when device is in autoselect mode. 13. Command sequence returns device to reading array after being placed in a Write-to-Buffer-Abort state. Full command sequence is required if resetting out of abort while in Unlock Bypass mode. 14. The Unlock-Bypass command is required prior to the Unlock-BypassProgram command. 15. The Unlock-Bypass-Reset command is required to return to reading array data when the device is in the unlock bypass mode. 16. The system can read and program/program suspend in non-erasing sectors, or enter the autoselect mode, when in the Erase Suspend mode. The Erase Suspend command is valid only during a sector erase operation. 17. The Erase Resume/Program Resume command is valid only during the Erase Suspend/Program Suspend modes. 18. The Exit command returns the device to reading the array. 68 S29GL-P MirrorBit(R) Flash Family S29GL-P_00_A7 November 8, 2007 Da ta Shee t (Prelimi nar y) Password Protection Lock Register Command (Notes) Global Non-Volatile Global Volatile Freeze Bus Cycles (Notes 1-5) First/Seventh Second Third Fourth Addr Data Addr Data Addr Data 555 40 555 60 Command Set Entry 3 555 AA 2AA 55 Program (6) 2 XXX A0 XXX DATA DATA Addr Data Read (6) 1 77h Command Set Exit (7, 8) 2 XXX 90 XXX 00 Command Set Entry 3 555 AA 2AA 55 Password Program (9) 2 XXX A0 PWA x PWD x Password Read (10) 4 00 PWD0 01 PWD 1 02 PWD 2 03 PWD 3 00 25 00 03 00 PWD 0 01 PWD 1 00 29 XXX 90 XXX 00 555 C0 555 50 555 E0 Password Unlock (10) Command Set Exit (7, 8) Volatile Cycles Table 12.2 S29GL-P Sector Protection Command Definitions, x16 Fifth Sixth Addr Data Addr Data 02 PWD 2 03 PWD 3 7 2 PPB Command Set Entry 3 555 AA 2AA 55 PPB Program (11, 12) 2 XXX A0 SA 00 All PPB Erase (13) 2 XXX 80 00 30 PPB Status Read (12) 1 SA RD (0) PPB Command Set Exit (7, 8) 2 XXX 90 XXX 00 PPB Lock Command Set Entry 3 555 AA 2AA 55 PPB Lock Set (12) 2 XXX A0 XXX 00 PPB Lock Status Read (12) 1 XXX RD (0) PPB Lock Command Set Exit (7, 8) 2 XXX 90 XXX 00 DYB Command Set Entry 3 555 AA 2AA 55 DYB Set (11, 12) 2 XXX A0 SA 00 DYB Clear (12) 2 XXX A0 SA 01 XXX 00 DYB Status Read (12) 1 SA RD (0) DYB Command Set Exit (7, 8) 2 XXX 90 Legend X = Don't care RD(0) = Read data. SA = Sector Address. Address bits Amax-A16 uniquely select any sector. PWD = Password PWDx = Password word0, word1, word2, and word3. Data = Lock Register Contents: PD(0) = Secured Silicon Sector Protection Bit, PD(1) = Persistent Protection Mode Lock Bit, PD(2) = Password Protection Mode Lock Bit. Notes 1. See Table 7.1 on page 19 for description of bus operations. 7. The Exit command returns the device to reading the array. 2. All values are in hexadecimal. 8. If any Command Set Entry command was written, an Exit command must be issued to reset the device into read mode. 3. All bus cycles are write cycles unless otherwise noted. 4. Data bits DQ15-DQ8 are don't cares for unlock and command cycles. 5. Address bits AMAX:A16 are don't cares for unlock and command cycles, unless SA or PA required. (AMAX is the Highest Address pin.) 6. All Lock Register bits are one-time programmable. Program state = "0" and the erase state = "1." The Persistent Protection Mode Lock Bit and the Password Protection Mode Lock Bit cannot be programmed at the same time or the Lock Register Bits Program operation aborts and returns the device to read mode. Lock Register bits that are reserved for future use default to "1's." The Lock Register is shipped out as "FFFF's" before Lock Register Bit program execution. November 8, 2007 S29GL-P_00_A7 9. For PWDx, only one portion of the password can be programmed per each "A0" command. 10. Note that the password portion can be entered or read in any order as long as the entire 64-bit password is entered or read. 11. If ACC = VHH, sector protection matches when ACC = VIH. 12. Protected State = "00h," Unprotected State = "01h." 13. The All PPB Erase command embeds programming of all PPB bits before erasure. S29GL-P MirrorBit(R) Flash Family 69 Data Sheet (Pre limin ar y) Command (Notes) Cycles Table 12.3 S29GL-P Memory Array Command Definitions, x8 Bus Cycles (Notes 1-5) First Addr Data RD Read (6) 1 RA Reset (7) Autoselect (8,9) Second Addr Third Data Addr Fourth Data Addr Fifth Data 1 XXX F0 Manufacturer ID 4 AAA AA 555 55 AAA 90 X00 01 Device ID (8) 4 AAA AA 555 55 AAA 90 X02 XX7E Sector Protect Verify (10) 4 AAA AA 555 55 AAA 90 [SA]X04 (10) Secure Device Verify (11) 4 AAA AA 555 55 AAA 90 X06 (11) CFI Query (12) 1 AA 98 Program 4 AAA AA 555 55 AAA A0 PA PD Write to Buffer 3 AAA AA 555 55 SA 25 SA WC Program Buffer to Flash (confirm) 1 SA 29 Write-to-Buffer-Abort Reset (13) Sixth Addr Data Addr Data X1C (8) X1E (8) WBL PD WBL PD AAA AA 555 55 555 F0 3 AAA AA 555 55 AAA 20 Program (14) 2 XXX A0 PA PD Sector Erase (14) 2 XXX 80 SA 30 Chip Erase (14) 2 XXX 80 XXX 10 Reset (15) 2 XXX 90 XXX 00 Chip Erase 6 AAA AA 555 55 AAA 80 AAA AA 555 55 AAA 10 Sector Erase 6 AAA AA 555 55 AAA 80 AAA AA 555 55 SA 30 Erase Suspend/Program Suspend (16) 1 XXX B0 Erase Resume/Program Resume (17) 1 XXX 30 Secured Silicon Sector Entry 3 AAA AA 555 55 AAA 88 Secured Silicon Sector Exit (18) 4 AAA AA 555 55 AAA 90 XX 00 Unlock Bypass 3 Enter Legend X = Don't care RA = Address of the memory to be read. RD = Data read from location RA during read operation. PA = Address of the memory location to be programmed. Addresses latch on the falling edge of the WE# or CE# pulse, whichever happens later. Notes 1. See Table 7.1 on page 19 for description of bus operations. 2. All values are in hexadecimal. 3. All bus cycles are write cycles unless otherwise noted. 4. Data bits DQ15-DQ8 are don't cares for unlock and command cycles. 5. Address bits AMAX:A16 are don't cares for unlock and command cycles, unless SA or PA required. (AMAX is the Highest Address pin.). 6. No unlock or command cycles required when reading array data. 7. The Reset command is required to return to reading array data when device is in the autoselect mode, or if DQ5 goes high (while the device is providing status data). 8. See Table 7.2 on page 22 for device ID values and definitions. 9. The fourth, fifth, and sixth cycles of the autoselect command sequence are read cycles. 10. The data is 00h for an unprotected sector and 01h for a protected sector. See Autoselect on page 21 for more information. This is same as PPB Status Read except that the protect and unprotect statuses are inverted here. PD = Data to be programmed at location PA. Data latches on the rising edge of the WE# or CE# pulse, whichever happens first. SA = Address of the sector to be verified (in autoselect mode) or erased. Address bits Amax-A16 uniquely select any sector. WBL = Write Buffer Location. The address must be within the same write buffer page as PA. WC = Word Count is the number of write buffer locations to load minus 1. 11. The data value for DQ7 is "1" for a serialized, protected Secured Silicon Sector region and "0" for an unserialized, unprotected region. See Table 7.3 on page 22 for data and definitions. 12. Command is valid when device is ready to read array data or when device is in autoselect mode. 13. Command sequence returns device to reading array after being placed in a Write-to-Buffer-Abort state. Full command sequence is required if resetting out of abort while in Unlock Bypass mode. 14. The Unlock-Bypass command is required prior to the Unlock-BypassProgram command. 15. The Unlock-Bypass-Reset command is required to return to reading array data when the device is in the unlock bypass mode. 16. The system can read and program/program suspend in non-erasing sectors, or enter the autoselect mode, when in the Erase Suspend mode. The Erase Suspend command is valid only during a sector erase operation. 17. The Erase Resume/Program Resume command is valid only during the Erase Suspend/Program Suspend modes. 18. The Exit command returns the device to reading the array. 70 S29GL-P MirrorBit(R) Flash Family S29GL-P_00_A7 November 8, 2007 Da ta Shee t (Prelimi nar y) Bus Cycles (Notes 1-5) First/Seventh Second/Eighth Addr Data Addr Data Addr Data AA 555 55 AAA 40 XXX DATA 00 AAA 60 02 Command Set Entry 3 AAA Bits Program (6) 2 XXX A0 Read (6) 1 00 DATA Command Set Exit (7, 8) 2 XXX 90 XXX Command Set Entry 3 AAA AA 555 55 Password Program (9) 2 XXX A0 PWA x PWD x Password Read (10) 8 Password Unlock (10) 11 Command Set Exit (7, 8) 2 PPB Command Set Entry 3 Fourth Fifth Sixth Addr Data Addr Data Addr Data PWD 2 03 PWD 3 04 PWD 4 05 PWD 5 03 PWD 3 01 PWD 1 PWD 6 07 PWD 7 00 25 00 03 00 PWD 0 01 PWD 1 02 PWD 2 04 PWD 4 05 PWD 5 06 PWD 6 07 PWD 7 00 29 XXX 90 XXX 00 AAA AA 55 55 AAA C0 2 XXX A0 SA 00 All PPB Erase (13) 2 XXX 80 00 30 PPB Status Read (12) 1 SA RD(0) 00 AAA 50 AAA E0 Global Non-Volatile PWD0 06 PPB Program (11, 12) PPB Command Set Exit (7, 8) 2 XXX 90 XXX PPB Lock Command Set Entry 3 AAA AA 555 55 PPB Lock Bit Set (12) 2 XXX A0 XXX 00 00 Volatile Third 00 Global Volatile Freeze Password Protection Lock Register Command (Notes) Cycles Table 12.4 S29GL-P Sector Protection Command Definitions, x8 PPB Lock Status Read (12) 1 XXX RD(0) PPB Lock Command Set Exit (7, 8) 2 XXX 90 XXX DYB Command Set Entry 3 AAA AA 555 55 DYB Set (11, 12) 2 XXX A0 SA 00 DYB Clear (12) 2 XXX A0 SA 01 DYB Status Read (12) 1 SA RD(0) DYB Command Set Exit (7, 8) 2 XXX 90 XXX 00 Legend X = Don't care RD(0) = Read data. SA = Sector Address. Address bits Amax-A16 uniquely select any sector. PWD = Password PWDx = Password word0, word1, word2, and word3. Data = Lock Register Contents: PD(0) = Secured Silicon Sector Protection Bit, PD(1) = Persistent Protection Mode Lock Bit, PD(2) = Password Protection Mode Lock Bit. Notes 1. See Table 7.1 on page 19 for description of bus operations. 7. The Exit command returns the device to reading the array. 8. If any Command Set Entry command was written, an Exit command must be issued to reset the device into read mode. 2. All values are in hexadecimal. 3. All bus cycles are write cycles unless otherwise noted. 4. Data bits DQ15-DQ8 are don't cares for unlock and command cycles. 5. Address bits AMAX:A16 are don't cares for unlock and command cycles, unless SA or PA required. (AMAX is the Highest Address pin.) 6. All Lock Register bits are one-time programmable. Program state = "0" and the erase state = "1." The Persistent Protection Mode Lock Bit and the Password Protection Mode Lock Bit cannot be programmed at the same time or the Lock Register Bits Program operation aborts and returns the device to read mode. Lock Register bits that are reserved for future use default to "1's." The Lock Register is shipped out as "FFFF's" before Lock Register Bit program execution. November 8, 2007 S29GL-P_00_A7 9. For PWDx, only one portion of the password can be programmed per each "A0" command. 10. Note that the password portion can be entered or read in any order as long as the entire 64-bit password is entered or read. 11. If ACC = VHH, sector protection matches when ACC = VIH. 12. Protected State = "00h," Unprotected State = "01h." 13. The All PPB Erase command embeds programming of all PPB bits before erasure. S29GL-P MirrorBit(R) Flash Family 71 Data 12.2 Sheet (Pre limin ar y) Common Flash Memory Interface The Common Flash Interface (CFI) specification outlines device and host system software interrogation handshake, which allows specific vendor-specified software algorithms to be used for entire families of devices. Software support can then be device-independent, JEDEC ID-independent, and forward- and backward-compatible for the specified flash device families. Flash vendors can standardize their existing interfaces for long-term compatibility. This device enters the CFI Query mode when the system writes the CFI Query command, 98h, to address 55h any time the device is ready to read array data. The system can read CFI information at the addresses given in Tables 12.6-12.8). All reads outside of the CFI address range, returns non-valid data. Reads from other sectors are allowed, writes are not. To terminate reading CFI data, the system must write the reset command. The system can also write the CFI query command when the device is in the autoselect mode. The device enters the CFI query mode, and the system can read CFI data at the addresses given in Tables 12.6-12.8. The system must write the reset command to return the device to reading array data. The following is a C source code example of using the CFI Entry and Exit functions. Refer to the Spansion Low Level Driver User's Guide (available on www.spansion.com) for general information on Spansion Flash memory software development guidelines. /* Example: CFI Entry command */ *( (UINT16 *)base_addr + 0x55 ) = 0x0098; /* Example: CFI Exit command */ *( (UINT16 *)base_addr + 0x000 ) = 0x00F0; /* write CFI entry command /* write cfi exit command */ */ For further information, please refer to the CFI Specification (see JEDEC publications JEP137-A and JESD68.01and CFI Publication 100). Please contact your sales office for copies of these documents. Table 12.5 CFI Query Identification String 72 Addresses (x16) Addresses (x8) Data 10h 11h 12h 20h 22h 24h 0051h 0052h 0059h Query Unique ASCII string "QRY" 13h 14h 26h 28h 0002h 0000h Primary OEM Command Set 15h 16h 2Ah 2Ch 0040h 0000h Address for Primary Extended Table 17h 18h 2Eh 30h 0000h 0000h Alternate OEM Command Set (00h = none exists) 19h 1Ah 32h 34h 0000h 0000h Address for Alternate OEM Extended Table (00h = none exists) Description S29GL-P MirrorBit(R) Flash Family S29GL-P_00_A7 November 8, 2007 Da ta Shee t (Prelimi nar y) Table 12.6 System Interface String Addresses (x16) Addresses (x8) Data 1Bh 36h 0027h Description VCC Min. (write/erase) D7-D4: volt, D3-D0: 100 mV 1Ch 38h 0036h VCC Max. (write/erase) D7-D4: volt, D3-D0: 100 mV 1Dh 3Ah 0000h VPP Min. voltage (00h = no VPP pin present) 1Eh 3Ch 0000h VPP Max. voltage (00h = no VPP pin present) 1Fh 3Eh 0006h Typical timeout per single byte/word write 2N s 20h 40h 0006h Typical timeout for Min. size buffer write 2N s (00h = not supported) 21h 42h 0009h Typical timeout per individual block erase 2N ms 22h 44h 0013h Typical timeout for full chip erase 2N ms (00h = not supported) 23h 46h 0003h Max. timeout for byte/word write 2N times typical 24h 48h 0005h Max. timeout for buffer write 2N times typical 25h 4Ah 0003h Max. timeout per individual block erase 2N times typical 26h 4Ch 0002h Max. timeout for full chip erase 2N times typical (00h = not supported) Table 12.7 Device Geometry Definition Addresses (x16) Addresses (x8) Data 27h 4Eh 001Bh 001Ah 0019h 0018h 28h 29h 50h 52h 0002h 0000h Flash Device Interface description (refer to CFI publication 100) 2Ah 2Bh 54h 56h 0006h 0000h Max. number of byte in multi-byte write = 2N (00h = not supported) 2Ch 58h 0001h Number of Erase Block Regions within device (01h = uniform device, 02h = boot device) 2Dh 2Eh 2Fh 30h 5Ah 5Ch 5Eh 60h 00xxh 000xh 0000h 000xh Erase Block Region 1 Information (refer to the CFI specification or CFI publication 100) 00FFh, 0003h, 0000h, 0002h =1 Gb 00FFh, 0001h, 0000h, 0002h = 512 Mb 00FFh, 0000h, 0000h, 0002h = 256 Mb 007Fh, 0000h, 0000h, 0002h = 128 Mb 31h 32h 33h 34h 60h 64h 66h 68h 0000h 0000h 0000h 0000h Erase Block Region 2 Information (refer to CFI publication 100) 35h 36h 37h 38h 6Ah 6Ch 6Eh 70h 0000h 0000h 0000h 0000h Erase Block Region 3 Information (refer to CFI publication 100) 39h 3Ah 3Bh 3Ch 72h 74h 76h 78h 0000h 0000h 0000h 0000h Erase Block Region 4 Information (refer to CFI publication 100) November 8, 2007 S29GL-P_00_A7 Description Device Size = 2N byte 1B = 1 Gb, 1A= 512 Mb, 19 = 256 Mb, 18 = 128 Mb S29GL-P MirrorBit(R) Flash Family 73 Data Sheet (Pre limin ar y) Table 12.8 Primary Vendor-Specific Extended Query Addresses (x16) Addresses (x8) Data 40h 41h 42h 80h 82h 84h 0050h 0052h 0049h Query-unique ASCII string "PRI" 43h 86h 0031h Major version number, ASCII 44h 88h 0033h Minor version number, ASCII 0014h Address Sensitive Unlock (Bits 1-0) 0 = Required, 1 = Not Required 45h 8Ah Description Process Technology (Bits 7-2) 0101b = 90 nm MirrorBit 46h 8Ch 0002h Erase Suspend 0 = Not Supported, 1 = To Read Only, 2 = To Read & Write 47h 8Eh 0001h Sector Protect 0 = Not Supported, X = Number of sectors in per group 48h 90h 0000h Sector Temporary Unprotect 00 = Not Supported, 01 = Supported 49h 92h 0008h Sector Protect/Unprotect scheme 0008h = Advanced Sector Protection 4Ah 94h 0000h Simultaneous Operation 00 = Not Supported, X = Number of Sectors 4Bh 96h 0000h Burst Mode Type 00 = Not Supported, 01 = Supported 4Ch 98h 0002h Page Mode Type 00 = Not Supported, 01 = 4 Word Page, 02 = 8 Word Page 4Dh 9Ah 00B5h 4Eh 9Ch 00C5h 4Fh 9Eh 00xxh 50h A0h 0001h ACC (Acceleration) Supply Minimum 00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV ACC (Acceleration) Supply Maximum 00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV WP# Protection 74 04h = Uniform sectors bottom WP# protect, 05h = Uniform sectors top WP# protect Program Suspend 00h = Not Supported, 01h = Supported S29GL-P MirrorBit(R) Flash Family S29GL-P_00_A7 November 8, 2007 Da ta Shee t (Prelimi nar y) 13. Advance Information on S29GL-R 65 nm MirrorBit Hardware Reset (RESET#) and Power-up Sequence Table 13.1 Hardware Reset (RESET#) Parameter Limit Time tRPH RESET# Low to CE# Low Description Min 35 Unit s tRP RESET# Pulse Width Min 200 ns tRH Time between RESET# (high) and CE# (low) Min 200 ns Limit Time Unit Note CE#, OE# and WE# must be at logic high during Reset Time. Figure 13.1 Reset Timings tRP RESET# tRH tRPH CE# Note The sum of tRP and tRH must be equal to or greater than tRPH. Table 13.2 Power-Up Sequence Timings Parameter Description tVCS VCC Setup Time to first access Min 300 s tVIOS VIO Setup Time to first access Min 300 s tRPH RESET# Low to CE# Low Min 35 s tRP RESET# Pulse Width Min 200 ns tRH Time between RESET# (high) and CE# (low) Min 200 ns Notes 1. VIO < VCC + 200 mV. 2. VIO and VCC ramp must be in sync during power-up. If RESET# is not stable for 500 s, the following conditions may occur: the device does not permit any read and write operations, valid read operations return FFh, and a hardware reset is required. 3. Maximum VCC power up current is 20 mA (RESET# =VIL). Figure 13.2 Power-On Reset Timings VCC V IO t VIOS t VCS t RP RESET# t RH t RPH CE# Note The sum of tRP and tRH must be equal to or greater than tRPH. November 8, 2007 S29GL-P_00_A7 S29GL-P MirrorBit(R) Flash Family 75 Data Sheet (Pre limin ar y) 14. Revision History Section Description Revision A0 (October 29, 2004) Initial Release. Revision A1 (October 20, 2005) Global Revised all sections of document. Revision A2 (October 19, 2006) Global Revised all sections of document. Reformatted document to new template. Changed speed options for S29GL01GP. Revision A3 (November 21, 2006) AC Characteristics Erase and Program Operations table: Changed tBUSY to a maximum specification. Revision A4 (December 18, 2006) Global Changed tACC, tCE specifications on 128 Mb, 256 Mb, and 512 Mb devices. Added 90 and 100 ns speed options. Write Buffer Programming, Sector Erase Write Buffer Programming Operation, Sector Erase Operation figures: Deleted "Wait 4 ms" box from flowcharts. Password Protection Method Lock Register Program Algorithm figure: Deleted "Wait 4 ms" box from flowchart. Read-only Operations table Modified tRC, tACC, tCE, tOE specifications. Program and Erase Operations tables Changed tDS specification, deleted write cycle time note. TSOP Pin and BGA Capacitance table Changed all specifications in table. Revision A5 (May 18, 2007) Global Changed data sheet status to Preliminary. Deleted references to requirement for external WP# pullup. Performance Characteristics Max. Read Access Times table: Added note. Hardware Reset Deleted note from section. AC Characteristics Reset Timings figure: Deleted note. Command Definitions tables S29GL-P Sector Protection Command Definitions tables: Changed "Global Non-Volatile Freeze" to "Global Volatile Freeze". DC Characteristics CMOS Compatible table: Changed ICC1 maximum current for 5 MHz and MHz test conditions. Page Read Timings figure Corrected address range for top waveform. Revision A6 (October 23, 2007) Performance Characteristics Changed speed options for S29GL512P Ordering Information Corrected samples OPN valid combinations; changed speed options for S29GL512P 64-Ball Fortified BGA Clarified ball "D1" connection 56-Pin TSOP Clarified pin "30" connection Autoselect Added recommendation statement Accelerated Program Added recommendation statement Persistent Protection Bits Removed "Erase" from title and flow chart Secured Silicon Sector Sections "Factory Locked Secured Silicon Sector" & "Customer Lockable Secured Silicon Sector": clarified shipping options Power-up Sequence Timing Changed tRH from "Max" to "Min" value Advance Information on S29GL-R 65 nm MirrorBit Hardware Reset (RESET#) and Power-up Sequence Added section Global Fixed cross-references that were not live hyperlinks. Revision A7 (November 8, 2007) Advance Information on S29GL-R 65 nm MirrorBit Hardware Reset (RESET#) Changed timing specs and waveforms and Power-up Sequence 76 S29GL-P MirrorBit(R) Flash Family S29GL-P_00_A7 November 8, 2007 Da ta Shee t (Prelimi nar y) Colophon The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for any use that includes fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for any use where chance of failure is intolerable (i.e., submersible repeater and artificial satellite). Please note that Spansion will not be liable to you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. If any products described in this document represent goods or technologies subject to certain restrictions on export under the Foreign Exchange and Foreign Trade Law of Japan, the US Export Administration Regulations or the applicable laws of any other country, the prior authorization by the respective government entity will be required for export of those products. Trademarks and Notice The contents of this document are subject to change without notice. This document may contain information on a Spansion product under development by Spansion. Spansion reserves the right to change or discontinue work on any product without notice. The information in this document is provided as is without warranty or guarantee of any kind as to its accuracy, completeness, operability, fitness for particular purpose, merchantability, non-infringement of third-party rights, or any other warranty, express, implied, or statutory. Spansion assumes no liability for any damages of any kind arising out of the use of the information in this document. Copyright (c) 2004-2007 Spansion Inc. All rights reserved. Spansion(R), the Spansion Logo, MirrorBit(R), MirrorBit(R) EclipseTM, ORNANDTM, HDSIMTM and combinations thereof, are trademarks of Spansion LLC in the US and other countries. Other names used are for informational purposes only and may be trademarks of their respective owners. November 8, 2007 S29GL-P_00_A7 S29GL-P MirrorBit(R) Flash Family 77