SN55115, SN75115
DUAL DIFFERENTIAL RECEIVERS
SLLS072D – SEPTEMBER 1973 – REVISED MAY 1998
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
D
Choice of Open-Collector or Active Pullup
(Totem-Pole) Outputs
D
Single 5-V Supply
D
Differential Line Operation
D
Dual-Channel Operation
D
TTL Compatible
D
±15-V Common-Mode Input Voltage Range
D
Optional-Use Built-In 130-ΩLine-
Terminating Resistor
D
Individual Frequency-Response Controls
D
Individual Channel Strobes
D
Designed for Use With SN55113, SN75113,
SN55114, and SN75114 Drivers
D
Designed to Be Interchangeable With
National DS9615 Line Receivers
description
The SN55115 and SN75115 dual differential line
receivers are designed to sense small differential
signals in the presence of large common-mode
noise. These devices give TTL-compatible output
signals as a function of the differential input
voltage. The open-collector output configuration
permits the wire-ANDing of similar TTL outputs
(such as SN5401/SN7401) or other
SN55115/SN75115 line receivers. This permits a
level of logic to be implemented without extra
delay.
The output stages are similar to TTL totem-pole outputs, but with sink outputs, 1YS and 2YS, and the
corresponding active pullup terminals, 1YP and 2YP, available on adjacent package pins. The frequency
response and noise immunity may be provided by a single external capacitor. A strobe input is provided for each
channel. With the strobe in the low level, the receiver is disabled and the outputs are forced to a high level.
The SN55115 is characterized for operation over the full military temperature range of –55°C to 125°C. The
SN75115 is characterized for operation from 0°C to 70°C.
FUNCTION TABLE
STRB DIFF INPUT
(A AND B)
OUTPUT
(YP AND YS
TIED
TOGETHER)
L X H
HLH
HHL
H = VI ≥ VIH min or VID more positive than VT+ max
L = VI ≤ VIL max or VID more negative thanVT– max
X = irrelevant
Copyright 1998, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
1YS
1YP
1STRB
1RTC
1B
1RT
1A
GND
VCC
2YS
2YP
2STRB
2RTC
2B
2RT
2A
SN55115 ...J OR W PACKAGE
SN75115 ...N PACKAGE
(TOP VIEW)
3212019
910111213
4
5
6
7
8
18
17
16
15
14
2YP
2STRB
NC
2RTC
2B
1STRB
1RTC
NC
1B
1RT
SN55114 . . . FK PACKAGE
(TOP VIEW)
1YP
1YS
NC
2YS
1A
GND
NC
NC – No internal connection
CC
V
2A
2RT
SN55115, SN75115
DUAL DIFFERENTIAL RECEIVERS
SLLS072D – SEPTEMBER 1973 – REVISED MAY 1998
2POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
logic symbol†
&
2YS
2YP
1YS
1YP
RT
RSP
12
13
10
9
11
4
3
6
7
5
2RTC
2STRB
2RT
2A
2B
1RTC
1STRB
1RT
1A
1B
15
14
1
2
†This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12.
logic diagram (positive logic)
11
9
10
12
13
2YP (Pullup)
2YS (Sink)
14
15
2B
2A
2RT
2RTC
2STRB
1STRB
1RTC
1RT
1A
1B 1
21YP (Pullup)
3
4
6
7
5
1YS (Sink)
SN55115, SN75115
DUAL DIFFERENTIAL RECEIVERS
SLLS072D – SEPTEMBER 1973 – REVISED MAY 1998
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
schematic (each receiver)
YS
Sink
1.64 k 130
Input 7.9
VVV
V
150
2.5 k
Common to
Both Receivers
A8 k
7 k
1 pF
1.5 k 1.64 k
B
Input 5.1 1
130 150
150
8 k
7 k
1 pF
1 k 1 k
2.6 k
500
2.6 k
500
150 1.5 k
3 k
5 k
20
2 k
RT
6,10 Strobe
3,13
Response
Time
Control
4,12
2.7 k
16 VCC
2,14 Pullup
YP
1,15 Output
8GND
Resistor values are nominal and in ohms.
Pin numbers shown are for the J, N, and W packages.
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage, VCC (see Note 1) 7 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input voltage VI (A, B, and RT) ±25 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input voltage VI (STRB) 5.5 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Off-state voltage applied to open-collector outputs 14 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Continuous total power dissipation See Dissipation Rating Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature range, Tstg –65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Case temperature for 60 seconds: FK package 260°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds: J or W package 300°C. . . . . . . . . . . . . . . .
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: N package 260°C. . . . . . . . . . . . . . . . . . . . .
†Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only , and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may af fect device reliability.
NOTE 1: All voltage values, except differential input voltage, are with respect to network ground terminal.
SN55115, SN75115
DUAL DIFFERENTIAL RECEIVERS
SLLS072D – SEPTEMBER 1973 – REVISED MAY 1998
4POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
DISSIPATION RATING TABLE
PACKAGE TA ≤ 25°C
POWER RATING DERATING FACTOR
ABOVE TA = 25°CTA = 70°C
POWER RATING TA = 125°C
POWER RATING
FK†1375 mW 11.0 mW/°C 880 mW 275 mW
J†1375 mW 11.0 mW/°C 880 mW 275 mW
N 1150 mW 9.2 mW/°C 736 mW —
W†1000 mW 8.0 mW/°C 640 mW 200 mW
†In the FK, J, and W packages, SN55115 chips are either silver glass or alloy mounted. SN75115 chips are
glass mounted.
recommended operating conditions
SN55115 SN75115
UNIT
MIN NOM MAX MIN NOM MAX
UNIT
Supply voltage, VCC 4.5 5 5.5 4.75 5 5.25 V
High-level input voltage at STRB, VIH 2.4 2.4 V
Low-level input voltage at STRB, VIL 0.4 0.4 V
High-level output current, IOH –5 –5 mA
Low-level output current, IOL 15 15 mA
Operating free-air temperature, TA–55 125 0 70 °C
SN55115, SN75115
DUAL DIFFERENTIAL RECEIVERS
SLLS072D – SEPTEMBER 1973 – REVISED MAY 1998
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
PARAMETER
TEST CONDITIONS†
SN55115 SN75115
UNIT
PARAMETER
TEST
CONDITIONS†
MIN TYP‡MAX MIN TYP‡MAX
UNIT
VIT+§Positive-going
threshold voltage VO = 0 .4 V, IOL = 15 mA, VIC = 0 500 500 mV
VIT–§Negative-going
threshold voltage VO = 2 .4 V, IOH = –5 mA, VIC = 0 –500¶–500¶mV
VICR Common-mode
input voltage range VID = ±1 V +15
to
–15
+24
to
–19
+15
to
–15
+24
to
–19 V
Hi h l l t
V MIN
V05V
TA = MIN 2.2 2.4
VOH High-level ouput
voltage
VCC = MIN,
IOH =
–
5mA
VID = –0.5 V, TA = 25°C2.4 3.4 2.4 3.4 V
voltage
IOH
=
–
5
mA
TA = MAX 2.4 2.4
VOL Low-level output
voltage VCC = MIN,
IOL = 15 mA VID = –0.5 V, 0.22 0.4 0.22 0.45 V
Lllit
V MAX V 0 4 V
TA = MIN –0.9 –0.9
IIL Low-level input
current
VCC = MAX, VI = 0.4 V,
Other in
p
ut at 5 5 V
TA = 25°C –0.5 –0.7 –0.5 –0.7 mA
current
Other
in ut
at
5
.
5
V
TA = MAX –0.7 –0.7
ISH
High-level strobe V
CC
= MIN, V
ID
= –0.5 V, TA = 25°C 2 5
µA
I
SH
g
current
CC ,
Vstrobe = 4.5 V
ID ,
TA = MAX 5 10 µ
A
ISL Low-level strobe
current VCC = MAX,
Vstrobe = 0.4 V VID = 0.5 V, TA = 25°C –1.15 –2.4 –1.15 –2.4 mA
I(RTC) Response-time-
control current VCC = MAX,
VRC = 0 VID = 0.5 V, TA = 25°C –1.2 –3.4 –1.2 –3.4 mA
V
CC
= MIN, V
OH
= 12 V, TA = 25°C 100
IO(off)
Off-state
o
p
en collector
CC ,
VID = –4.5 V
OH ,
TA = MAX 200
µA
I
O
(off)
open-co
ll
ec
t
or
o
u
tp
u
t
cu
rr
e
nt V
CC
= MIN, V
OH
= 5.25 V, TA = 25°C 100 µ
A
out ut
current
CC ,
VID = –4.75 V
OH ,
TA = MAX 200
RTLine-terminating
resistance VCC = 5 V TA = 25°C 77 130 167 74 130 179 Ω
IOS Supply-circuit output
current#VCC = MAX,
VO = 0 VID = –0.5 V, TA = 25°C–15 –40 –80 –14 –40 –100 mA
ICC Supply current
(both receivers) VCC = MAX,
VIC = 0 VID = 0.5 V, TA = 25°C 32 50 32 50 mA
†Unless otherwise noted, Vstrobe = 2.4 V . All parameters with the exception of off-state open-collector output current are measured with the active
pullup connected to the sink output.
‡All typical values are at VCC = 5 V, TA = 25°C, and VIC = 0.
§Differential voltages are at the B input terminal with respect to the A input terminal.
¶The algebraic convention, in which the less positive (more negative) limit is designated as minimum, is used in this data sheet for threshold
voltages only.
#Only one output should be shorted to ground at a time, and duration of the short circuit should not exceed one second.
SN55115, SN75115
DUAL DIFFERENTIAL RECEIVERS
SLLS072D – SEPTEMBER 1973 – REVISED MAY 1998
6POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
switching characteristics, VCC = 5 V, CL = 30 pF, TA = 25°C
PARAMETER
TEST CONDITIONS
SN55115 SN75115
UNIT
PARAMETER
TEST
CONDITIONS
MIN TYP MAX MIN TYP MAX
UNIT
tPLH Propagation delay time,
low-to-high level output RL = 3.9 kΩ,See Figure 1 18 50 18 75 ns
tPHL Propagation delay time,
high-to-low level output RL = 390 Ω,See Figure 1 20 50 20 75 ns
PARAMETER MEASUREMENT INFORMATION
STRB
90%
0 V 0 V 10%
90%
≤ 5 ns ≤ 5 ns
tPHL
1.5 V VOL
VOH
–3 V
3 V
Output
Differential
Input
tPLH
1.5 V
VO
RL
5 V
YP
YS CL = 30 pF
(see Note B)
Response
Time Control
Open
2.4 VOpen
RT
B
A
Input
Pulse
Generator
(see Note A) 10%
TEST CIRCUIT VOLTAGE WAVEFORM
NOTES: A. The pulse generator has the following characteristics: ZO = 50 Ω, PRR ≤ 500 kHz, tw ≤ 100 ns, duty cycle = 50%.
B. CL includes probe and jig capacitance.
Figure 1. Test Circuit and Voltage Waveforms
SN55115, SN75115
DUAL DIFFERENTIAL RECEIVERS
SLLS072D – SEPTEMBER 1973 – REVISED MAY 1998
7
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS†
0
–2
–4
–6
–25 –20–15–10 –5 0 5
II – Input Current – mA
2
4
INPUT CURRENT
vs
INPUT VOLTAGE
6
10 15 20 25
VCC = 5 V
Input Not Under Test at 0 V
TA = 25°C
VI – Input Voltage – V
II
Figure 2
Figure 3
OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
ICC – Output Voltage – V
TA – Free-Air Temperature – °C
ÎÎÎÎÎ
VCC = 4.5 V
2
1.6
0.8
0.4
0
3.4
1.2
2.8
2.4
3.2
4
– 75 – 50 – 25 0 25 50 75 100 125
ÎÎÎÎÎÎÎÎÎ
VOH (VID = –0.5 V, IOH = –5 mA)
ÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
VOL (VID = 0.5 V, IOL = 15 mA)
ÁÁ
ÁÁ
ÁÁ
CC
I
Figure 4
OUTPUT VOLTAGE
vs
COMMON-MODE INPUT VOLTAGE
3
2
1
0
–25–20–15–10 –5 0 5
4
5
6
10 15 20 25
ÎÎÎÎ
ÎÎÎÎ
No Load
TA = 25°C
ÎÎÎÎÎ
VCC = 5.5 V
ÎÎÎÎ
ÎÎÎÎ
VID = – 1 V
ÎÎÎÎ
ÎÎÎÎ
VID = 1 V
ÎÎÎÎ
ÎÎÎÎ
VCC = 5 V
ÎÎÎÎÎ
ÎÎÎÎÎ
VCC = 4.5 V
VO – Output Voltage – V
VIC – Common-Mode Input Voltage – V
ÁÁ
ÁÁ
VO
†Data for temperatures below 0°C and above 70°C and for supply voltages below 4.75 V and above 5.25 V are applicable to SN55115 circuits
only. These parameters were measured with the active pullup connected to the sink output.
SN55115, SN75115
DUAL DIFFERENTIAL RECEIVERS
SLLS072D – SEPTEMBER 1973 – REVISED MAY 1998
8POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 5
HIGH-LEVEL OUTPUT VOLTAGE
vs
HIGH-LEVEL OUTPUT CURRENT
2
1
00 –10
3
4
5
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
VID = –0.5 V
TA = 25°C
ÎÎÎÎÎ
ÎÎÎÎÎ
VCC = 5.5 V
ÎÎÎÎ
VCC = 5 V
ÎÎÎÎÎ
ÎÎÎÎÎ
VCC = 4.5 V
VOH – High-Level Output Voltage – V
IOH – High-Level Output Current – mA
ÁÁ
ÁÁ
VOH
–50
–40–30–20
Figure 6
VCC = 4.5 V
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT CURRENT
0
VOL – Low-Level Output Voltge – V
IOL– Low-Level Output Current – mA
0.4
30
05 10 15 20 25
0.1
0.2
0.3
ÎÎÎÎ
ÎÎÎÎ
TA = 25°C
ÎÎÎÎÎ
VCC = 5.5 V
ÁÁ
ÁÁ
VOL
VID = 0.5 V
Figure 7
OUTPUT VOLTAGE
vs
DIFFERENTIAL INPUT VOLTAGE
–0.2
VO – Output Voltage – V
6
0.2
0–0.1 0 0.1
1
2
3
4
5
TA = 125°C
TA = 25°C
TA = –55°C
VCC = 5 V
Load = 2 kΩ to VCC
VID – Differential Input Voltage – V
ÁÁÁ
ÁÁÁ
VO
Figure 8
ÁÁÁÁÁÁ
ÁÁÁÁÁÁ
OUTPUT VOLTAGE
vs
DIFFERENTIAL INPUT VOLTAGE
VO – Output Voltage – V
0.2–0.1 0 0.1
VCC = 5.5 V
VCC = 5 V
VCC = 4.5 V
–0.2
VID – Differential Input Voltage – V
6
0
1
2
3
4
5
Load = 2 kΩ to VCC
TA = 25°C
ÁÁ
ÁÁ
VO
–0.15 –0.05 0.5 0.15
SN55115, SN75115
DUAL DIFFERENTIAL RECEIVERS
SLLS072D – SEPTEMBER 1973 – REVISED MAY 1998
9
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS†
Figure 9
OUTPUT VOLTAGE
vs
STROBE INPUT VOLTAGE
0
VO – Output Voltage – V
Vstrobe – Strobe Input Voltage – V
6
4
0
1
2
3
4
5
123
V
CC = 5.5 V
VCC = 5 V
ÎÎÎÎ
VCC = 4.5 V
ÁÁ
ÁÁ
VO
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
No Load
ÎÎÎÎÎ
ÎÎÎÎÎ
VID = 0.5 V
TA = 25°C
0.5 1.5 2.5 3.5
Figure 10
OUTPUT VOLTAGE
vs
STROBE INPUT VOLTAGE
0
VO – Output Voltage – V
Vstrobe – Strobe Input Voltage – V
6
4
0
1
2
3
4
5
123
T
A
= 125°C
TA = –55°C
TA = 25°C
ÁÁ
ÁÁ
VO
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
VCC = 5 V
No Load
VID = 0.5 V
0.5 1.5 2.5 3.5
Figure 11
SUPPLY CURRENT
(BOTH RECEIVERS)
vs
SUPPLY VOLTAGE
0
ICC – Supply Current – mA
VCC – Supply Voltage – V
60
8
01234567
10
20
30
40
50
B Input at VCC
A Input at 0 V
B Input at 0 V
A Input at VCC
ÁÁ
ÁÁ
CC
I
ÎÎÎÎ
ÎÎÎÎ
No Load
TA = 25°C
Figure 12
SUPPLY CURRENT
(BOTH RECEIVERS)
vs
FREE-AIR TEMPERATURE
–75
ICC – Supply Current – mA
TA – Free-Air Temperature – °C
40
125
0–50 –25 0 25 50 75 100
5
10
15
20
25
30
35
VCC = 5.5 V
B Input at 5.5 V
ÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎ
A Input at 0 V
ÁÁ
ÁÁ
ÁÁ
CC
I
†Data for temperatures below 0°C and above 70°C and for supply voltages below 4.75 V and above 5.25 V are applicable to SN55115 circuits
only. These parameters were measured with the active pullup connected to the sink output.
SN55115, SN75115
DUAL DIFFERENTIAL RECEIVERS
SLLS072D – SEPTEMBER 1973 – REVISED MAY 1998
10 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS†
Figure 13
PROPAGATION DELAY TIMES
vs
FREE-AIR TEMPERATURE
–75
Propagation Delay Times – ns
TA – Free-Air Temperature – °C
30
125
0–50 –25 0 25 50 75 100
5
10
15
20
25
VCC = 5 V
See Figure 1
tPHL (RL = 390 Ω)
tPLH (RL = 3.9 kΩ)
Figure 14
MAXIMUM OPERATING FREQUENCY
vs
RESPONSE-TIME-CONTROL CAPACITANCE
0.001
fmax – Maximum Operating Frequency – Hz
Response-T ime-Control Capacitance – µF
10M
10
100 0.01 0.1 1
1k
10k
1M
ÎÎÎÎ
VCC = 5 V
ÎÎÎÎÎÎÎÎÎÎ
Input: – 0.5-V to 0.5-V Square W ave
ÎÎÎÎ
ÎÎÎÎ
TA = 25°C
max
f
†Data for temperatures below 0°C and above 70°C and for supply voltages below 4.75 V and above 5.25 V are applicable to SN55115 circuits
only. These parameters were measured with the active pullup connected to the sink output.
APPLICATION INFORMATION
Location 1
SN75113 Driver
SN75115 Receiver
Location 3
Location 2
Location 5
Location 4
Location 6
Twisted
Pair
ZO‡ZO‡
‡ZO = RT. A capacitor may be connected in series with ZO to reduce power dissipation.
Figure 15. Basic Party-Line or Data-Bus Differential Data Transmission
PACKAGE OPTION ADDENDUM
www.ti.com 25-Jan-2012
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status (1) Package Type Package
Drawing Pins Package Qty Eco Plan (2) Lead/
Ball Finish MSL Peak Temp (3) Samples
(Requires Login)
5962-88745012A ACTIVE LCCC FK 20 1 TBD Call TI Call TI
5962-88745012A-T ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type
5962-8874501FA ACTIVE CFP W 16 1 TBD Call TI Call TI
JM38510/10404BEA ACTIVE CDIP J 16 1 TBD A42 N / A for Pkg Type
M38510/10404BEA ACTIVE CDIP J 16 1 TBD A42 N / A for Pkg Type
SN55115J ACTIVE CDIP J 16 1 TBD A42 N / A for Pkg Type
SN75115D ACTIVE SOIC D 16 40 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
SN75115DE4 ACTIVE SOIC D 16 40 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
SN75115DG4 ACTIVE SOIC D 16 40 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
SN75115DR ACTIVE SOIC D 16 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
SN75115DRE4 ACTIVE SOIC D 16 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
SN75115DRG4 ACTIVE SOIC D 16 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
SN75115N ACTIVE PDIP N 16 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type
SN75115NE4 ACTIVE PDIP N 16 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type
SN75115NSR ACTIVE SO NS 16 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
SN75115NSRE4 ACTIVE SO NS 16 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
SN75115NSRG4 ACTIVE SO NS 16 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
SNJ55115FK ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type
SNJ55115J ACTIVE CDIP J 16 1 TBD A42 N / A for Pkg Type
SNJ55115W ACTIVE CFP W 16 1 TBD A42 N / A for Pkg Type
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
PACKAGE OPTION ADDENDUM
www.ti.com 25-Jan-2012
Addendum-Page 2
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF SN55115, SN75115 :
•Catalog: SN75115
•Military: SN55115
NOTE: Qualified Version Definitions:
•Catalog - TI's standard catalog product
•Military - QML certified for Military and Defense Applications
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
SN75115DR SOIC D 16 2500 330.0 16.4 6.5 10.3 2.1 8.0 16.0 Q1
SN75115NSR SO NS 16 2000 330.0 16.4 8.2 10.5 2.5 12.0 16.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 14-Jul-2012
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
SN75115DR SOIC D 16 2500 333.2 345.9 28.6
SN75115NSR SO NS 16 2000 367.0 367.0 38.0
PACKAGE MATERIALS INFORMATION
www.ti.com 14-Jul-2012
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
