Microwave Ceramics Filter RXLO 2-Pole Filter for GSM 1800 Base Station Series/Type: Ordering code: S2B5/2/1 B69842N1507A580 Date: Version: November 2010 A Content of header bars 1 and 2 of data sheet will be automatically entered in headers and footers! Please fill in the table and then change the color to "white". This ensures that the table disappears (invisible) for the customer PDF. Don't change formatting when entering or pasting text in the table and don't add any cell or line in and to it! Identification/Classification 1 (header 1 + top left bar): Microwave Ceramics Filter Identification/Classification 2 (header 2 + bottom left header bar): RXLO 2-Pole Filter for GSM 1800 Base Station Ordering code: (top right header bar) B69842N1507A580 Series/Type: (top right header bar) S2B5/2/1 Preliminary data (optional): (if necessary) Data sheet Department: SAW MLIP CER PD Date: November 2010 Version: A Prepared by: Pauritsch Release signed by: Reichel Release signed QS: Modifications/Remarks: EPCOS AG 2010. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited Microwave Ceramics Filter RXLO 2-Pole Filter for GSM 1800 Base Station B69842N1507A580 S2B5/2/1 Modification P1 P2 P3 A 1st version derived from design goal F2037 Features, component drawing, soldering reqirements, tape d i Upgraded new form Final Version / actual dimensions / no tape color 30.08.04 14.10.04 27.01.10 21.09.10 Gavela Stadlerl Reichel Reichel Features Monolithic ceramic body covered with metal (Sn) Low losses High power durability No moisture sensitivity: MSL =1 (at soldering temperature = +260 C) SAW MLIP CER PD Please read Cautions and warnings and Important notes at the end of this document. November 2010 Page 2 of 7 Microwave Ceramics Filter RXLO 2-Pole Filter for GSM 1800 Base Station B69842N1507A580 S2B5/2/1 Component drawing Bottom view onto the solder terminals and side view Marking: EPCOS logo, LO DCS 1800 on top of the filter Recommended footprint solder pads ground area below solder resist with vias to second ground layer connected to lines with an impedance of 50 Ohm FR4 material permitivity : 4.4 preferred thickness : 0.3 Vias: O0.3mm / mm For other thickness correlation might be necessary SAW MLIP CER PD Please read Cautions and warnings and Important notes at the end of this document. November 2010 Page 3 of 7 Microwave Ceramics Filter RXLO 2-Pole Filter for GSM 1800 Base Station B69842N1507A580 S2B5/2/1 Characteristics Min. Center frequency fc - Insertion loss in passband (1460 ... 1540 MHz) IL Typ. Max. 1500 - MHz 0.4 0.5 dB B 80 Passband (1460 ... 1540 MHz) Amplitude ripple (peak - peak) (1460 ... 1540 MHz) Standing wave ratio MHz 0.2 dB SWR 1.4 Nominal input/output impedance Z 50 Attenuation 50 20 dB dB dB at DC to 200 MHz 200 ... 300 MHz 1700 ... 2800 MHz 50 17 1.5 Maximum ratings IEC climatic category (IEC 68-1) -40 / +90/56 Operating temperature Top -40 / +85 Maximum Input Level 30 C dBm Typical passband characteristics 300 800 1300 1800 2300 0 attenuation [dB] -10 -20 S11 -30 S21 -40 -50 -60 frequency [MHz] SAW MLIP CER PD Please read Cautions and warnings and Important notes at the end of this document. November 2010 Page 4 of 7 Microwave Ceramics Filter RXLO 2-Pole Filter for GSM 1800 Base Station B69842N1507A580 S2B5/2/1 Processing information Acc. to IEC 68-2-58: 75% (after aging) Wettability Soldering requirements Profile for eutectic SnPb solder paste Profile for lead-free solder paste Soldering type Reflow Reflow Maximum soldering temperature (measuring point on top surface of the component) 235 C (max. 2 s) 260 C (max. 2 s) 225 C (max. 10 s) 250 C (max. 10 s) Recommended soldering conditions (infrared) within 10 sec. Temp. [C] within 10 sec. Temp. [C] 250 250 215C10C 245C5C 200 200 150 150 100 100 50 50 20-40 sec. Time [sec.] 40-80 sec. SAW MLIP CER PD Please read Cautions and warnings and Important notes at the end of this document. 30 sec. 2.5 C/s 2-3 min. Time [sec.] > - 5 C/s November 2010 Page 5 of 7 Microwave Ceramics Filter RXLO 2-Pole Filter for GSM 1800 Base Station B69842N1507A580 S2B5/2/1 Delivery mode Blister tape acc. to IEC 286-3 Pieces/tape: 400 SAW MLIP CER PD Please read Cautions and warnings and Important notes at the end of this document. November 2010 Page 6 of 7 Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. The aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the "General Terms of Delivery for Products and Services in the Electrical Industry" published by the German Electrical and Electronics Industry Association (ZVEI). 7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSMP, CSSP, CTVS, DeltaCap, DigiSiMic, DSSP, FormFit, MiniBlue, MiniCell, MKD, MKK, MLSC, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks. Page 7 of 7