Terminal Blocks - Single Row Series A2000, LP2000 & CB2000 Single Row Terminal Blocks A20510807WR SPECIFICATIONS Rating: A2: 30A, 300V* LP2: 30A, 150V* CB2: 30A, 300V* Center Spacing: 0.375" or 3/8" (9.52mm) Wire Range: #12-22 AWG CU Screw Size: #6-32 zinc-plated philslot LP202110 Torque Rating: 9 lb-in. Base: Standoffs standard for easy flux washing Distance Between Barriers: 0.32" (8.1mm) Recommended PCB Hole Diameter: 0.076" (1.93mm) Operating Temperature: 105C (221F) max., -40C (-40F) min. Molded Material: Black, UL Rated 94V0 Thermoplastic Breakdown Voltage: 3400V (A2 & LP2); 4100V (CB2). Agency Information: UL File E62622, CSA File 47235; IEC Compliance; CE Certified *30A Rating achieved with a #10 copper wire crimped to a ring terminal.; 20A Rating without ring terminal. CB20210507 Dimensions - in (mm) A2000 & LP2000 Series Poles 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 MOUNTING ENDS ONLY A C Mount Ctrs. Length 1.13 1.50 1.88 2.25 2.63 3.00 3.38 3.75 4.13 4.50 4.88 5.25 5.63 6.00 6.38 6.75 7.13 7.50 7.88 8.25 8.63 9.00 9.38 9.75 10.13 10.50 10.88 11.25 11.63 - - 1.56 1.93 2.30 2.68 3.06 3.43 3.81 4.18 4.56 4.93 5.31 5.69 6.06 6.43 6.81 7.18 7.56 7.93 8.31 8.68 9.06 9.43 9.81 10.18 10.56 10.93 11.31 11.68 12.05 - - BARRIER & MOUNTING ENDS B Pole Ctrs. BARRIER ENDS ONLY C Length 0.38 0.75 1.13 1.50 1.88 2.25 2.63 3.00 3.38 3.75 4.13 4.50 4.88 5.25 5.63 6.00 6.38 6.75 7.13 7.50 7.88 8.25 8.63 9.00 9.38 9.75 10.13 10.50 10.88 11.25 11.63 0.81 1.18 1.56 1.93 2.31 2.68 3.06 3.43 3.81 4.18 4.56 4.93 5.31 5.68 6.06 6.43 6.81 7.18 7.56 7.93 8.31 8.68 9.06 9.43 9.81 10.18 10.55 10.93 11.31 11.68 12.05 0.375 (9.53) 0.15 (3.8) O 0.65 (16.5) C Mount End Barrier End 0.76 (19.3) 0.565 (14.35) on LP2000 0.40 (10.2) 0.02 (0.5) A Mount Centers B Pole Centers Mount End Barrier End CB2000 Series 0.375 (9.53) 0.19 (4.8) O 0.32 (8.1) 0.70 (17.8) C Mount End Barrier End * Dimensions in inches. To convert to millimeters, multiply by 25.4. 0.60 (15.2) 0.02 (0.5) A Mount Centers B Pole Centers Mount End Barrier End Terminal Blocks - Single Row Terminal Blocks: Single & Double Row Series A2000 & LP2000 Single Row Terminal Blocks Part Numbering System Series Base/End Poles Screw Options Options Blank - std. screw 00 - screws shipped bulk 03 - stainless steel 04 - brass nickel-plated 07 - steel SEMS (not available with hardware options) 09 - brass SEMS nickel-plated (not available with hardware options) CA - captive screw WR - wire ready (not available on LP2 series) AB - angle mnt. options (pg 9) A1 to A9 - 0.250 QC B1 to B9 - 0.187 QC DR - drilled right angle (pg 9) JA, JB & JC - barrier jumpers L1 to L6 marking options (pg 22) MP, MP8 & MT mounting plates (pg 9) OJ2 & OJ4 - over barrier jumpers (not available w/covers) RC - retaining clips (pg 9) R30 to R77 - right angle bends (pg 9) SO - stand off insulators (pg 9) S1 - solder lug/flat A2 - standard barrier 01 - handwired LP2 - low profile 02 - printed circuit barrier 03 - non feed-thru 04 - wire wrap tail 05 - extended handwired 06 - handwired 07 - extended pin 08 - printed circuit 09 - 0.250 QC short 10 - 0.187 QC 14 - printed circuit 19 - 0.250 QC long 0 - flat base/molded 02 to 32 mount end 02 to 30 on mount 1 - flat base/mnt. end end base 2 - flat base/barrier end 3 - insulator base/mnt. end 4 - insulator base/ barrier end 5 - closed base/ mount end 6 - closed base/ molded mount end 9 - insulator base/ molded mount end Covers - (pg 23) Power Distribution Blocks Base/End Note: 0, 6, 9 styles not available with covers. 5 & 6 Styles only available with 03 terminals. Contact factory for configuration... Terminal Styles Inches (Millimeters) 0.031 (.79) 0.110 (2.79) 0.031 (0.79) 01 Handwired 0.062 (1.57) 03 Non Feed-Thru 04 Wire Wrap Tail 0.031 (0.79) 05 Extended Handwired 0.11 (2.79) 0.055 (1.40) 0.14 (3.6) 0.17 (4.3) 0.032 (0.81) 0.031 (0.79) 08 Printed Circuit 07 Extended Pin 06 Handwired 0.062 (1.57) 0.33 (8.4) 0.250 (6.35) 09 0.250 QC short 0.031 (0.79) 0.31 (7.9) 0.187 (4.75) 10 0.187 QC 0.41 (10.4) 0.031 (0.79) 0.125 (3.2) 14 Printed Circuit 0.062 (1.57) 0.031 (0.79) 0.250 (6.35) 19 0.250 QC long Compliance References 0.40 (10.2) 0.031 (0.79) 0.72 (18.3) 0.42 (10.7) Edge Connectors, One-Sided Boards 0.54 (13.7) 0.30 (7.6) 0.110 (2.79) 0.062 (1.57) 0.031 (0.79) 02 Printed Circuit 0.66 (16.8) 0.031 (0.79) 0.55 (14.0) 0.20 (5.1) Wire Management Products 0.55 (14.0) Terminal Blocks: Base & Rail Mount Terminal Style EuroMag Series A 2 L P 2 Terminal Blocks - Single Row Series A2000 & LP2000 Single Row Terminal Blocks Continued Screw Options Standard zinc-plated Steel 04 Brass Nickel-Plated 03 Stainless Steel Hardware Options WR Wire Ready 09 Brass SEMS Nickel-Plated Inches (Millimeters) (Bulk ordering part numbers are in parentheses.) Jumpers Solder Lugs 07 Steel SEMS Quick Connects Blade Width A = 0.250" Blade Width B = 0.187" 0.68 (17.3) 0.33 (8.4) 0.84 (21.2) JA (JA2-XX-J) S1 (2S1-J) OJ2 (OJ2-J) A1 & B1 (2A1-J & 2B1-J) A2 & B2 (2A2-J & 2B2-J) A3 & B3 (2A3-J & 2B3-J) OJ4 (OJ4-J) A4 & B4 (2A4-J & 2B4-J) A5 & B5 (2A5-J & 2B5-J) A6 & B6 (2A6-J & 2B6-J) A7 & B7 (2A7-J & 2B7-J) A8 & B8 (2A8-J & 2B8-J) A9 & B9 (2A9-J & 2B9-J) 0.33 (8.4) JB (JB2-XX-J) 0.33 (8.4) Contact factory for configuration. JC (JC2-XX-J) Base/End Options Inches (Millimeters) B B B 0.180 (4.57) 0.150 O (3.8) mounting holes (2) 0.218 (5.54) 0.40 (10.2) 0.40 (10.2) 0.095 (2.4) SECTION A-A 0, 6 & 9 Molded Mount End SECTION B-B 1, 3 & 5 Mount End B Terminal Blocks - Single Row Series A2000 & LP2000 Single Row Terminal Blocks Continued Mounting Options Right Angle Bends (A2, LP2 only) Right angle terminals are offered on the A2000 & LP2000 Series. Configurations are defined in these dimensions: X = pin extension beyond the block base; Z = length from block base to centerline of the terminal tip. Standard bends consist of the X and Z dimensions shown in the chart. Specify by adding the selected Bend Option Code to the terminal part number. 07 Terminal Bend Configurations Z 04 Terminal Bend Configurations 0.82 X Z 0.55 Bend Option Code Bend Option Code X Z Available w/insulator base 0.28 0.23 0.22 0.19 0.16 0.12 0.10 0.08 No No No No No No No No X (minimum) R30 R35 R36 R39 R42 R46 R48 R50 0.04 0.01 0.02 0.05 0.08 0.12 0.14 0.16 R30 R35 R36 R42 R46 R50 R53 R66 R69 R75 R77 X (minimum) 0.04 0.01 0.02 0.08 0.12 0.16 0.19 0.32 0.35 0.41 0.43 Z Available w/insulator base 0.55 0.50 0.49 0.43 0.39 0.35 0.32 0.19 0.16 0.10 0.08 Yes Yes Yes Yes Yes No No No No No No Dimensions in inches. To convert to millimeters, multiply by 25.4. Drilled Right Angle (A2, LP2 only) Angle Brackets (A2, LP2 only) 0.12 5 0.32 0.25 0.04 0.45 0.144 HOLE w/0.312 C' BORE 0.32 0.15 ; Option AB Angle brackets enable block to be fastened at right angles to normal mount position. Bulk part number 2AB-J. Mounting Plates MOUNTING PLATE Option DR Counterbored holes across mount ends of block enable fastening with two screws at right angles to normal mount position. Standoffs Retaining Clip MP MP8 0.300 MT Options MP, MP8 & MT MP Metal inserts with 0.150" dia. hole accept #6 screw. MP8 Metal inserts with 0.187" dia. hole accept #8-32 screw. MT Metal inserts with tapped hole accept #6-32 screw. ; RETAINING CLIP STANDOFF Option SO Standoff mounts are tubes molded to the mounting positions. Available with insulator bases only. Option RC Use on standoff tubes. Fit panels up to 0.125" thick. Two clips for every five positions. Supplied unassembled. Bulk part number H541-J. Terminal Blocks - Single Row Series CB2000 Single Row Terminal Blocks Part Numbering System Series Terminal Style Base/End Poles Screws Options B 2 C CB2 - closed back 01 02 03 07 14 22 1 - mount end 2 - barrier end 02 to 32 02 to 30 on mount end base 03 - stainless steel 04 - brass nickel-plated 07 - steel SEMS standard 09 - brass SEMS nickel-plated CA - captive screw 07CA - SEMS captive *AB - angle mounting brackets (pg 11) A7 to A9 - 0.250" QC B7 to B9 - 0.187" QC EB - exit back terminals EF - exit front terminals JA, JB & JC - barrier jumpers L1 to L6 marking options (pg 22) LT1 to LT6 marking options (pg 22) OJ2 & OJ4 - over barrier jumpers MP, MP8, MT & MT8 mtg. plates (pg 11) S1 - solder lug/flat - handwired - printed circuit - non feed-thru - extended pin - printed circuit - dual tail printed circuit *Only available on 3-poles and up. Contact factory for configuration.. Terminal Styles Inches (Millimeters) 0.19 (4.9) 0.40 (10.2) 0.031 (0.79) 0.120 (3.05) 0.18 (4.6) 0.045 (1.14) 01 Handwired 0.031 (0.79) 02 Printed Circuit Screw Options 03 Stainless Steel (F507-J) 0.18 (4.6) 0.062 (1.57) 03 Non Feed-Thru Available on Mount End (1) only. 0.18 (4.6) 0.81 (4.6) 0.125 (3.18) 0.70 (17.8) 0.19 (4.8 ) 0.031 (0.79) 0.045 (1.14) 0.18 (4.6) 14 Printed Circuit 07 Extended Pin 0.031 (0.79) 0.045 (1.14) 0.03 (0.79) 0.40 (10.2) 0.43 (10.9) 22 Dual Tail Printred Circuit (Bulk ordering part numbers are in parentheses.) 04 Brass nickel-plated (F506-J) 07 Steel SEMS zinc-plated (BOO1-7084-J) 09 Brass SEMS nickel-plated (F524-J) * NOTE: Wire ready screws standard on all terminal styles. CB2 Terminal Exit Options Inches (Millimeters) 0.255 (6.48) 0.18 (4.6) Exit Rear (std.) 0.18 (4.6) EF Exit Front X EB Exit Back Terminal Blocks - Single Row Series CB2000 Single Row Terminal Blocks Hardware Options Solder Lugs Inches (Millimeters) (Bulk ordering part numbers are in parentheses.) Jumpers Quick Connects Blade Width A = 0.250". Blade Width B = 0.187". 0.68 (17.3) 0.33 (8.4) 0.84 (21.2) S1 (2S1-J) OJ2 (OJ2-J) JA (JA2-XX-J) A7 & B7 (2A7-J & 2B7-J) A8 & B8 (2A8-J & 2B8-J) A9 & B9 (2A9-J & 2B9-J) 0.33 (8.4) JB (JB2-XX-J) OJ4 (OJ4-J) 0.33 (8.4) JC (JC2-XX-J) Contact factory for configuration.. Mounting Options Inches (Millimeters) Right Angle Mounting Bracket End Positions usable 0.71 (18.0) Snap-in Angle Bracket Chassis or PCB A #6 or #8 mounting screw & nut (Customer supplied.) 0.79 (20.1) 1.02 (25.8) Exit Back (EB) Terminals 0.24 (6.1) Mounts blocks on PC boards at a right angle. * Protects solder joints. * Recommended for all EB (Exit Back) PCB terminal blocks. * Bracket snaps securely on block (no hardware required). * Minimum strip length (end positions are usable). * Mount with #6-32 or #8-32 screws (not supplied). Mounting Plates ; MP MP8 MOUNTING PLATE MT MT8 A 0.42 (10.7) Angle Bracket Option AB Options MP, MP8, MT & MT8 MP Metal inserts with 0.150" dia. hole accept #6 screw. MP8 Metal inserts with 0.187" dia. hole accept #8-32 screw. MT Metal inserts with tapped hole accept #6-32 screw. MT8 Metal inserts with tapped hole accept #8-32 screw. 0.45 (11.4) Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Cooper Bussmann: OJ4/J A201302 A202202 A202203 A20220307L1 A210406 A214204 A207006R42DR Eaton: A207409 A208205 A210310 A20440404 A201321 A203117B7 A20221009 A203603 A20221603 A20222107 A207305R35 A204212 A203102A3 A20441603 A203516 A20711604MP A207216R53 A20221404 A207203R53 A209108 A20431607 A20310807 A207303R35 A20120607 A208112 A207212R35 A20130507L1 A20220504 A204202 A20130900MP A203105 A20710807 A20222603 A204410 A20731207CAR50 A20821004 A20350807MP A203503B9 A207306R46SO A21420307 A207416 A20220607CA A21020307 A20110904 A20610604 A20220903 A20222407 A20130807 A20130307 A20741203 A20220207L1 A204217 A209104 A204204R35 A206112 A20420707 A207202R46 A20140807RC A20220404 A205312 A20221007CA A209103 A207207 A20220907CA A20720607R75 A20130407 A20111004 A20220704 A207407 A206205CA A21420407 A204412 A202230 A20420604 A202219 A210306 A207324 A21422307 A20740309 A20310907 A204203 A20350607S1L1 A204209 A20720807R46 A203105B9 A20432004 A20420507 A20741307R46 A20221103 A20312407 A20820204 A20820507WR A207306 A206014 A203506MP A20220507WR A20220804 A201413RC A203514MP A209112