Monolithic Hall Effect ICs EM-series EM-1791 Shipped in packet-tape reel(5000pcs/Reel) EM-1791 is ultra-small Hall effect ICs of a single silicon chip composed of Hall element and a signal processing IC. Unipolar Hall Effect Switch Two output for S and N-pole Supply Voltage 1.65.5 Output CMOS Two output for S and N-pole High Sensitivity Hall Element Pulse Excitation Bop2.5mT SMT Notice:It is requested to read and accept "IMPORTANT NOTICE" written on the back of the front cover of this catalogue. Operational Characteristics S or N Vout1 Vout 2 H H VOH Marking 1 VOH 2 1VDD Bh1 Bh2 2OUT 1S-pole 3OUT 2N-pole N or S L VOL 4VSS 0 Brp1 L Bop1 S-pole VOL Bop2 N-pole 0 Brp2 Magnetic flux density Magnetic flux density Functional Block Diagram 1VDD Absolute Maximum RatingsTa=25 Symbol Limit Unit Supply Voltage VDD -0.1 6.0 V Output Current Iout 0.5 mA Operating Temperature Range Topr -30 85 Storage Temperature Range Tstg -40 125 Switch 2OUT1 S-pole Dynamic Offset Cancellation Item 3OUT2 N-pole Oscillator Hall Chopper & Element Stabilizer Timing Logic Amplifier Schmitt Output Trigger Stage & Latch 4VSS Magnetic q and Electrical CharacteristicsTa=25 VDD=1.85V Magnetic Characteristics wTa=-3085 VDD=1.85V Item Symbol Conditions Supply Voltage VDD Min. Typ. 1.6 Max. Unit Item 5.5 V Operating Point BOP1 *1.4 2.5 3.2 BOP2 -3.2 -2.5 *-1.4 Brp1 1.2 2.0 *3.0 Operating Point mT Brp2 *-3.0 H y s t e r e s i s Bh1,Bh2 P e r i o d Hysteresis mT Release Point -1.2 0.5 50 Tp Output High Voltage VOH Io=-0.2mA VDD-0.4 Output Low Voltage VOL Io=0.2mA Supply Current IDD -2.0 Average 45 Min. BOPS BOPN BrpS BrpN Typ. Max. Unit 1.3 2.5 3.5 mT 1.1 2.0 3.3 mT BhS 0.5 BhN mT 100 ms 0.4 9 V A Application Circuit 1mT=10Gauss The characteristics with*marks are design targets. OUT1 responds to the positive flux from the south pole(Bop1,Brp1) ,OUT2 to the negative flux from the north pole(Bop2,Brp2) . VDD CMOS OUT1 VDD EM-1791 OUT2 Conditions Note) The above specifications are design targets. V 6.5 Release Point Symbol CMOS Bypass Capacitor 0.1F VSS GND mT EM-1791 *Please be aware that our products are not intended for use in life support equipment, devices, or systems. Use of our products in such applications requires the advance written approval of our sales staff. Certain applications using semiconductor devices may involve potential risks of personal injury, property damage, or loss of life. In order to minimize these risks, adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. Inclusion of our products in such applications is understood to be fully at the risk of the customer using our devices or systems. a PackageUnit:mm) (For reference only)Land PatternUnit:mm) 0.50 1 0.3 Sensor center 00.1 0.90 2.10.2 1.250.1 2 0.25 2.10.1 1.3 0.3 5 1.90 5 3 4 0.05 0.1 0.55-0 0.3 0.25 0.1 5 5 Pin No. 1 2 3 4 Pin Name Function Comment VDD Supply Voltage S-pole OUT1 Output Voltage OUT2 Output Voltage N-pole VSS GND Note1) The sensor center is located within the 0.3mm circle. Note2) The tolerances of dimensions with no mentions is 0.1mm. Note3) Coplanarity:The differnces between standoff of terminals are max.0.1mm. Note4) The sensor part is located 0.4mm(typ.) far from marking surface. Function Timing Chart IDD f 1.30 IDD Pulse DrivingVDD=1.85V IDD 50ms t B t B Bop 146s IDD ON TYP1.8mA j Brp t Vout High Vout High 48.8s IDD t TYP6.5A IDD OFF TYP1.3A 48.8s Time Low Low t Operating Point Timing Release Point Timing t T h i s H all IC s output is held as inter nal dat a just befor e the int er nal cir c u it t u r n s O F F ( I D D O F F ) . A n d a f t e r 4 8 . 8 s , t h e o u t p u t c h a n g e s . N o t e ) 4 8 . 8 s i n f i g u r e s i s t y p i c a l v a l u e Supply Voltage Temparature Dependence of Bop. Brp 4 6 3 Operating PointmT Supply VoltageV 5 4 3 2 1 2 S-pole 1 0 -40 -20 0 20 40 60 Ambient Temperature 80 100 n Brp1 o VDD1.85V p -1 Brp2 N-pole -2 -3 0 Bop1 -4 -40 Bop2 -20 0 20 40 60 80 100 Ambient Temperature 46 IMPORTANT NOTICE These products and their specifications are subject to change without notice. When you consider any use or application of these products, please make inquiries the sales office of Asahi Kasei Microdevices Corporation (AKM) or authorized distributors as to current status of the products. Descriptions of external circuits, application circuits, software and other related information contained in this document are provided only to illustrate the operation and application examples of the semiconductor products. You are fully responsible for the incorporation of these external circuits, application circuits, software and other related information in the design of your equipments. AKM assumes no responsibility for any losses incurred by you or third parties arising from the use of these information herein. AKM assumes no liability for infringement of any patent, intellectual property, or other rights in the application or use of such information contained herein. Any export of these products, or devices or systems containing them, may require an export license or other official approval under the law and regulations of the country of export pertaining to customs and tariffs, currency exchange, or strategic materials. AKM products are neither intended nor authorized for use as critical componentsNote1) in any safety, life support, or other hazard related device or systemNote2), and AKM assumes no responsibility for such use, except for the use approved with the express written consent by Representative Director of AKM. As used here: Note1) A critical component is one whose failure to function or perform may reasonably be expected to result, whether directly or indirectly, in the loss of the safety or effectiveness of the device or system containing it, and which must therefore meet very high standards of performance and reliability. Note2) A hazard related device or system is one designed or intended for life support or maintenance of safety or for applications in medicine, aerospace, nuclear energy, or other fields, in which its failure to function or perform may reasonably be expected to result in loss of life or in significant injury or damage to person or property. It is the responsibility of the buyer or distributor of AKM products, who distributes, disposes of, or otherwise places the product with a third party, to notify such third party in advance of the above content and conditions, and the buyer or distributor agrees to assume any and all responsibility and liability for and hold AKM harmless from any and all claims arising from the use of said product in the absence of such notification. April 4, 2012