MIC4102 100V Half Bridge MOSFET Driver with Anti-Shoot Through Protection PRELIMINARY SPECIFICATIONS General Description Features The MIC4102 is a high frequency, 100V Half Bridge MOSFET driver IC featuring internal anti-shoot-through protection. The low-side and high-side gate drivers are controlled by a single input signal to the PWM pin. The MIC4102 implements adaptive anti-shoot-through circuitry to optimize the switching transitions for maximum efficiency. The single input control also reduces system complexity and greatly simplifies the overall design. The MIC4102 also features a low-side drive disable pin. This gives the MIC4102 the capability to operate in a nonsynchronous buck mode. This feature allows the MIC4102 to start up into applications where a bias voltage may already be present without pulling the output voltage down. Under-voltage protection on both the low-side and highside supplies forces the outputs low. An on-chip boot-strap diode eliminates the discrete diode required with other driver ICs. The MIC4102 is available in the SOIC-8L package with a junction operating range from -40C to +125C. Data sheets and support documentation can be found on Micrel's web site at www.micrel.com. * Drives high- and low-side N-Channel MOSFETs with single input * Adaptive anti-shoot-through protection * Low side drive disable pin * Bootstrap supply voltage to 118V DC * Supply voltage up to 16V * TTL input thresholds * On-chip bootstrap diode * Fast 30ns propagation times * Drives 1000pF load with 10ns rise and 6ns fall times * Low power consumption * Supply under-voltage protection * 2.5 pull up , 1.5 pull down output resistance * Space saving SOIC-8L package * -40C to +125C junction temperature range Applications * * * * * * High voltage buck converters Networking / Telecom power supplies Automotive power supplies Current Fed Push-Pull Topologies Ultrasonic drivers Avionic power supplies ___________________________________________________________________________________________________________ Typical Application 100V Buck Regulator Solution Micrel Inc. * 2180 Fortune Drive * San Jose, CA 95131 * USA * tel +1 (408) 944-0800 * fax + 1 (408) 474-1000 * http://www.micrel.com November 2006 M9999-112806 Micrel, Inc. MIC4102 Ordering Information Part Number Standard Pb-Free MIC4102BM MIC4102YM Input Junction Temp. Range Package TTL -40 to +125C SOIC-8L Pin Configuration VDD 1 8 LO HB 2 7 VSS HO 3 6 LS HS 4 5 PWM SOIC-8L (M) Pin Description Pin Number Pin Name Pin Function 1 VDD Positive Supply to lower gate drivers. Decouple this pin to VSS (Pin 7). Bootstrap diode connected to HB (pin 2). 2 HB High-Side Bootstrap supply. External bootstrap capacitor is required. Connect positive side of bootstrap capacitor to this pin. Bootstrap diode is on-chip. 3 HO High-Side Output. Connect to gate of High-Side power MOSFET. 4 HS High-Side Source connection. Connect to source of High-Side power MOSFET. Connect negative side of bootstrap capacitor to this pin. 5 PWM Control Input. PWM high signal makes high-side HO output high, and low-side LO output low. PWM low signal makes high-side HO output low, and low-side LO output high. 6 LS Low-Side Disable. When pulled low, this control signal immediately terminates the low-side LO output drive. The low-side LO output drive will remain low until this signal is removed. HS drive is not affected by the LS signal. Here is the logic table: LS PWM LO HO 0 0 0 0 0 1 0 1 1 0 1 0 1 1 0 1 7 VSS Chip negative supply, generally will be grounded. 8 LO Low-Side Output. Connect to gate of Low-Side power MOSFET. November 2006 2 M9999-112806 Micrel, Inc. MIC4102 Absolute Maximum Ratings(1) Operating Ratings(2) Supply Voltage (VDD, VHB - VHS) ...................... -0.3V to 18V Input Voltages (VPWM, VLS) ..................... -0.3V to VDD + 0.3V Voltage on LO (VLO) .............................. -0.3V to VDD + 0.3V Voltage on HO (VHO) ......................VHS - 0.3V to VHB + 0.3V Voltage on HS (continuous) .............................. -1V to 110V Voltage on HB ..............................................................118V Average Current in VDD to HB Diode.......................100mA Junction Temperature (TJ) ........................-55C to +150C Storage Temperature (Ts) ..........................-60C to +150C EDS Rating(3) ..............................................................Note 3 Supply Voltage (VDD)........................................ +9V to +16V Voltage on HS ................................................... -1V to 100V Voltage on HS (repetitive transient) .................. -5V to 105V HS Slew Rate............................................................ 50V/ns Voltage on HB ...................................VHS + 8V to VHS + 16V and............................................ VDD - 1V to VDD + 100V Junction Temperature (TJ) ........................ -40C to +125C Junction Thermal Resistance SOIC-8L (JA)...................................................140C/W Electrical Characteristics(4) VDD = VHB = 12V; VSS = VHS = 0V; No load on LO or HO; TA = 25C; unless noted. Bold values indicate -40C< TJ < +125C. Symbol Parameter Condition Min Typ Max Units 150 450 600 A 3 3.5 4.0 mA 25 150 200 A 1.5 2.5 3 mA 0.05 1 30 A Supply Current IDD VDD Quiescent Current PWM = 0V IDDO VDD Operating Current f = 500kHz IHB Total HB Quiescent Current PWM = 0V IHBO Total HB Operating Current f = 500kHz IHBS HB to VSS Current, Quiescent VHS = VHB = 110V Input Pins (TTL) VIL Low Level Input Voltage Threshold VIH High Level Input Voltage Threshold RI Input Pull-down Resistance 0.8 1.5 V 1.5 2.2 V 100 200 500 k 6.5 7.3 8.0 V Under Voltage Protection VDDR VDD Rising Threshold VDDH VDD Threshold Hysteresis VHBR HB Rising Threshold VHBH HB Threshold Hysteresis 0.5 6.0 7.0 V 8.0 0.4 V V Boost Strap Diode VDL Low-Current Forward Voltage IVDD-HB = 100A VDH Low-Current Forward Voltage IVDD-HB = 100mA RD Dynamic Resistance IVDD-HB = 100mA November 2006 3 0.4 0.55 0.70 V 0.7 0.8 1.0 V 1.0 1.5 2.0 M9999-112806 Micrel, Inc. MIC4102 Electrical Characteristics Symbol Parameter Condition Min Typ Max Units 0.18 0.3 0.4 V 0.25 0.3 0.45 V LO Gate Driver VOLL Low Level Output Voltage ILO = 160mA VOHL High Level Output Voltage ILO = -100mA, VOHL = VDD - VLO IOHL Peak Sink Current VLO = 0V 3 A IOLL Peak Source Current VLO = 12V 2 A HO Gate Driver 0.22 0.3 0.4 V 0.25 0.3 0.45 V VOLH Low Level Output Voltage IHO = 160mA VOHH High Level Output Voltage IHO = -100mA, VOHH = VHB - VHO IOHH Peak Sink Current VHO = 0V 3 A IOLH Peak Source Current VHO = 12V 2 A Switching Specifications (Anti-Shoot-Through Circuitry) tLOOFF Delay between PWM going high to LO going low 30 VLOOFF Voltage threshold for LO MOSFET to be considered OFF 1.7 tHOON Delay between LO OFF to HO going High 30 50 60 ns tHOOFF Delay between PWM going Low to HO going low 45 65 70 ns VSWth Switch Node Voltage Threshold when HO turns off 2.5 4 Delay between HO MOSFET being considered off to LO turning ON 30 tLOON 60 70 tLSOFF Delay between LS going low and LO turning OFF tSWTO Forced LO ON, if VLOTH is not detected 1 CL = 1000pF 120 45 60 ns V V ns 36 45 70 ns 250 450 ns Switching Specifications tR Either Output Rise Time (3V to 9V) CL = 1000pF 10 ns tF Either Output Fall Time (3V to 9V) CL = 1000pF 6 ns tR Either Output Rise Time (3V to 9V) CL = 0.1F tF Either Output Fall Time (3V to 9V) CL = 0.1F November 2006 4 0.33 0.6 0.8 s 0.2 0.3 0.4 s M9999-112806 Micrel, Inc. MIC4102 Electrical Characteristics (cont.) Symbol Parameter Condition Min Typ Max Units 40 60 ns Switching Specifications (cont.) tPW Minimum Input Pulse Width that changes the output with LS=5V tPW Minimum Output Pulse Width on HO with min pulse width on PWM with LS=5V tPW Minimum Input Pulse Width that changes the output with LS=0V Minimum Output Pulse Width on HO with min pulse width on PWM with LS=0V tBS CL=0 Note 6 CL=0 15 Note 6 CL=0 13 Note 6 CL=0 ns 20 ns 20 Note 6 Bootstrap Diode Turn-On or Turn-Off Time 10 ns Notes: 1. Exceeding the absolute maximum rating may damage the device. 2. The device is not guaranteed to function outside its operating rating. 3. Devices are ESD sensitive. Handling precautions recommended. Human body model, 1.5k in series with 100pF. 4. Specification for packaged product only. 5. All voltages relative to pin7, VSS unless otherwise specified. 6. Guaranteed by design. Not production tested. November 2006 5 M9999-112806 Micrel, Inc. MIC4102 Typical Characteristics November 2006 6 M9999-112806 Micrel, Inc. MIC4102 Typical Characteristics (cont.) November 2006 7 M9999-112806 Micrel, Inc. MIC4102 Timing Diagrams tHOOFF 45ns 70ns tHOON 30ns 60ns HO 6 4 2 LO tLOON 30ns 70ns 3. VLOOFF <1.7V Switch node (HS Pin) PWM 8 10 7. VSWth <(VDD-2.5V) 1 5 tLOOFF 30ns 60ns tLSOFF 36ns 70ns 9 LS Time Point Action 1-2 2-4 5-7 PWM signal goes high. This initiates the LO signal to go low. The delay between PWM high to (VLO -10%) is typically 30ns (tLOOFF) LO goes low. When LO reaches 1.7V (VLOOFF) the low side MOSFET is deemed to be off. The high side output HO then goes high. The delay between 3 and 4 is typically 30ns (THOON); this allows for large turn off delay times of MOSFETs. PWM goes low; HO goes low, typically within 45ns, tHOOFF. The switch node (HS pin) is then monitored; when the switch node is VDD-2.5V (VSWTH) the high side MOSFET is deemed to be off and the LO output goes high within typically 30ns (tLOON ). This is controlled by a one shot and remains high until PWM goes high. This is November 2006 8-10 8 because it is possible to have the SW node oscillate, and could easily bounce through 10V level. If the LO high transition has not happened within 250ns, it is forced to happen, unless the LS input is low. If at any time after 7 has occurred and LS pin goes low, the LO output will turn off within 36ns (VLSOFF). HO will remain off. The LS pin overrides all shoot through control logic. If LS is low at the start of the next cycle when PWM signal goes high then HO shall switch transition 1-4 as normal. I.e. PWM signal equals HO output, LO = 0V. M9999-112806 Micrel, Inc. MIC4102 Functional Diagram HV HB 2 UVLO LEVEL SHIFT PWM 5 DRIVER HO 3 HS 4 LEVEL SHIFT VDD 1 UVLO DRIVER LO 8 LS 6 VSS 7 Figure 1. MIC4102 Functional Block Diagram PWM input pin is referenced to the VSS pin. The voltage state of the input signal does not change the quiescent current draw of the driver. The threshold level is independent of the VDD supply voltage and there is no dependence between IVDD and the input signal amplitude. This feature makes the MIC4102 an excellent level translator that will drive high threshold MOSFETs from a low voltage PWM IC. Functional Description The MIC4102 is a high voltage, non-inverting, synchronous MOSFET driver that uses a single PWM input signal to alternately drive both high-side and lowside N-Channel MOSFETs. The block diagram of the MIC4102 is shown in Figure 1. The MIC4102 input is TTL compatible. The high-side output buffer includes a high speed level-shifting circuit that is referenced to the HS pin. An internal diode is used as part of a bootstrap circuit to provide the drive voltage for the high-side output. Low-Side Driver A block diagram of the low-side driver is shown in Figure 2. The low-side driver is designed to drive a ground (Vss pin) referenced N-channel MOSFET. Low driver impedances allow the external MOSFET to be turned on and off quickly. The rail-to-rail drive capability of the output ensures a low Rdson from the external MOSFET. A low level applied to PWM pin will cause the HO output to go low and the LO output to go high. The upper driver FET turns on and Vdd is applied to the gate of the external MOSFET. A high level on the PWM pin forces the LO output low by turning off the upper driver and turning on the lower driver which ground the gate of the external MOSFET. Pulling the LS pin low disables the LO pin. Startup and UVLO The UVLO circuit forces both driver outputs low until the supply voltage exceeds the UVLO threshold. The lowside UVLO circuit monitors the voltage between the VDD and VSS pins. The high-side UVLO circuit monitors the voltage between the HB and HS pins. Hysteresis in the UVLO circuit prevents noise and finite circuit impedance from causing chatter during turn-on. The VDD pin voltage is supplied to the HS pin through the internal bootstrap diode. The HB pin voltage will always be a diode drop less than VDD. Input Stage The MIC4102 utilizes a TTL compatible input stage. The November 2006 9 M9999-112806 Micrel, Inc. MIC4102 Vdd Drive Signal LO A low power, high speed, level shifting circuit isolates the low side (VSS pin) referenced circuitry from the highside (HS pin) referenced driver. Power to the high-side driver and UVLO circuit is supplied by the bootstrap circuit while the voltage level of the HS pin is shifted high. The bootstrap circuit consists of an internal diode and external capacitor, CB. In a typical application, such as the synchronous buck converter shown in Figure 4, the HS pin is at ground potential while the low-side MOSFET is on. The internal diode allows capacitor CB to charge up to VDD-VD during this time (where VD is the forward voltage drop of the internal diode). After the low-side MOSFET is turned off and the HO pin turns on, the voltage across capacitor CB is applied to the gate of the upper external MOSFET. As the upper MOSFET turns on, voltage on the HS pin rises with the source of the high-side MOSFET until it reaches VIN. As the HS and HB pin rise, the internal diode is reverse biased preventing capacitor CB from discharging. External FET LS Vss Figure 2. Low-Side Driver Block Diagram High-Side Driver and Bootstrap Circuit A block diagram of the high-side driver and bootstrap circuit is shown in Figure 3. This driver is designed to drive a floating N-channel MOSFET, whose source terminal is referenced to the HS pin. CB Vin HB Vdd Q1 CVDD Level shift Lout HO Vout HB Vdd PWM HS Q FF _ Q2 Cout LO Q CB HO External FET Vss Figure 4. High-Side Driver and Bootstrap Circuit HS Figure 3. High-Side Driver Block Diagram November 2006 10 M9999-112806 Micrel, Inc. MIC4102 Applications Information The total diode power dissipation is: Power Dissipation Considerations Power dissipation in the driver can be separated into three areas: An optional external bootstrap diode may be used instead of the internal diode (Figure 5). An external diode may be useful if high gate charge MOSFETs are being driven and the power dissipation of the internal diode is contributing to excessive die temperatures. The voltage drop of the external diode must be less than the internal diode for this option to work. The reverse voltage across the diode will be equal to the input voltage minus the Vdd supply voltage. A 100V Schottky diode will work for most 72V input telecom applications. The above equations can be used to calculate power dissipation in the external diode, however, if the external diode has significant reverse leakage current, the power dissipated in that diode due to reverse leakage can be calculated as: * Internal diode dissipation in the bootstrap circuit * Internal driver dissipation * Quiescent current dissipation used to supply the internal logic and control functions. Pdiode total = Pdiode fwd + Pdiode RR Bootstrap Circuit Power Dissipation Power dissipation of the internal bootstrap diode primarily comes from the average charging current of the CB capacitor times the forward voltage drop of the diode. Secondary sources of diode power dissipation are the reverse leakage current and reverse recovery effects of the diode. The average current drawn by repeated charging of the high-side MOSFET is calculated by: Pdiode REV = I R x VREV x (1 - D ) where : IR = Reverse current flow at VREV and TJ VREV = Diode Reverse Voltage I F ( AVE ) = Qgate x fS D = Duty Cycle = t ON / fS where : Q gate = Total Gate Charge at VHB fs = switching frequency of the power supply fS = gate drive switching frequency The average power dissipated by the forward voltage drop of the diode equals: The on-time is the time the high-side switch is conducting. In most power supply topologies, the diode is reverse biased during the switching cycle off-time. Pdiode fwd = I F ( AVE ) x VF where : VF = Diode forward voltage drop external diode The value of VF should be taken at the peak current through the diode, however, this current is difficult to calculate because of differences in source impedances. The peak current can either be measured or the value of VF at the average current can be used and will yield a good approximation of diode power dissipation. The reverse leakage current of the internal bootstrap diode is typically 11uA at a reverse voltage of 100V and 125C. Power dissipation due to reverse leakage is typically much less than 1mW and can be ignored. Reverse recovery time is the time required for the injected minority carriers to be swept away from the depletion region during turn-off of the diode. Power dissipation due to reverse recovery can be calculated by computing the average reverse current due to reverse recovery charge times the reverse voltage across the diode. The average reverse current and power dissipation due to reverse recovery can be estimated by: CB HB Vdd Level shift PWM Vin HO HS Q FF _ LO Q Vss Figure 5. Optional Bootstrap Diode I RR( AVE ) = 2 x I RRM x t rr x fS PdiodeRR = I RR( AVE ) x VREV Gate Drive Power Dissipation Power dissipation in the output driver stage is mainly caused by charging and discharging the gate to source and gate to drain capacitance of the external MOSFET. where : IRRM = Peak Reverse Recovery Current t rr = Reverse Recovery Time November 2006 11 M9999-112806 Micrel, Inc. MIC4102 Figure 6 shows a simplified equivalent circuit of the MIC4102 driving an external MOSFET. External FET HB Vdd Cgd Ron CB HO Rg Roff Rg_fet Cgs HS Figure 7. Typical Gate Charge vs. VGS The same energy is dissipated by Roff, Rg and Rg_fet when the driver IC turns the MOSFET off. Figure 6. MIC4103 Driving an External MOSFET Dissipation during the external MOSFET Turn-On Energy from capacitor CB is used to charge up the input capacitance of the MOSFET (Cgd and Cgs). The energy delivered to the MOSFET is dissipated in the three resistive components, Ron, Rg and Rg_fet. Ron is the on resistance of the upper driver MOSFET in the MIC4102. Rg is the series resistor (if any) between the driver IC and the MOSFET. Rg_fet is the gate resistance of the MOSFET. Rg_fet is usually listed in the power MOSFET's specifications. The ESR of capacitor CB and the resistance of the connecting etch can be ignored since they are much less than Ron and Rg_fet. The effective capacitance of Cgd and Cgs is difficult to calculate since they vary non-linearly with Id, Vgs, and Vds. Fortunately, most power MOSFET specifications include a typical graph of total gate charge vs. Vgs. Figure 7 shows a typical gate charge curve for an arbitrary power MOSFET. This chart shows that for a gate voltage of 10V, the MOSFET requires about 23.5nC of charge. The energy dissipated by the resistive components of the gate drive circuit during turn-on is calculated as: E= 1 2 E driver = and Pdriver = 1 x Qg x Vgs x fs 2 where E driver is the energy dissipated during turn - on or turn - off Pdriver is the power dissipated during turn - on or turn - off Qg is the total gate charge at Vgs Vgs is the gate to source voltage on the MOSFET fs is the switching frequency of the gate drive circuit The power dissipated inside the MIC4102 equals the ratio of Ron & Roff to the external resistive losses in Rg and Rg_fet. The power dissipated in the MIC4102 due to driving the external MOSFET is: Pdissdrive = Pdriver x Ron Roff + Pdriver x Ron + Rg + Rg _ fet Roff + Rg + Rg _ fet Supply Current Power Dissipation Power is dissipated in the MIC4102 even if is there is nothing being driven. The supply current is drawn by the bias for the internal circuitry, the level shifting circuitry and shoot-through current in the output drivers. The supply current is proportional to operating frequency and the Vdd and Vhb voltages. The typical characteristic graphs show how supply current varies with switching frequency and supply voltage. x Ciss x Vgs 2 but Q = Cx V so E = 1/2 x Qg x Vgs where Ciss is the total gate capacitance of the MOSFET November 2006 1 x Qg x Vgs 2 12 M9999-112806 Micrel, Inc. MIC4102 The power dissipated by the MIC4102 due to supply current is disadvantage is the driver cannot monitor the gate voltage inside the MOSFET. Figure 8 shows an equivalent circuit, including parasitics, of the gate driver section. The internal gate resistance (Rg_gate) and any external damping resistor (Rg) isolate the MOSFET's gate from the driver output. There is a delay between when the driver output goes low and the MOSFET turns off. This turn-off delay is usually specified in the MOSFET data sheet. This delay increases when an external damping resistor is used. Pdiss sup ply = Vdd x Idd + Vhb x Ihb Total power dissipation and Thermal Considerations Total power dissipation in the MIC41032 equals the power dissipation caused by driving the external MOSFETs, the supply current and the internal bootstrap diode . Pdisstotal = Pdiss sup ply + Pdissdrive + Pdiodetotal HB Vdd The die temperature may be calculated once the total power dissipation is known. Vin Ron Cgd TJ = T A + Pdiss total x JA HO where : TA is the maximum ambient temperatur e Rg_fet HS FET Rg Cgs Roff TJ is the junction temperatur e (C) HS Switching Node Pdiss total is the power dissipatio n of the MIC4102 JC is the thermal resistance from junction to ambient air (C/W) Ron Cgd LO Anti Shoot-Through, Propagation Delay and other Timing Considerations The block diagram in Figure 1 illustrates how the MIC4102 drives the power stage of a synchronous buck converter. It is important that only one of the two MOSFETs is on at any given time. If both MOSFETs are simultaneously on they will short Vin to ground, causing high current from the Vin supply to "shoot through" the MOSFETs into ground. Excessive shoot-through causes higher power dissipation in the MOSFETs, voltage spikes and ringing in the circuit. The high current and voltage ringing generate conducted and radiated EMI. Minimizing shoot-through can be done passively, actively or though a combination of both. Passive shootthrough protection uses delays between the high and low gate drivers to prevent both MOSFETs from being on at the same time. These delays can be adjusted for different applications. Although simple, the disadvantage of this approach is the long delays required to account for process and temperature variations in the MOSFET and MOSFET driver. Active shoot-though monitors voltages on the gate drive outputs and switch node to determine when to switch the MOSFETs on and off. This active approach adjusts the delays to account for some of the variations, but it too has its disadvantages. High currents and fast switching voltages in the gate drive and return paths can cause parasitic ringing that may turn the MOSFETs back on even though the gate driver output is low. Another November 2006 Rg_fet LS FET Cgs Roff Vss Figure 8. Gate Drive Circuit with Parasitics The MIC4102 uses a combination of active sensing and passive delay to insure that both MOSFETs are not on at the same time and to minimize shoot-through current. The timing diagram helps illustrate how the anti-shootthrough circuitry works. A high level on the PWM pin causes the LO pin to go low. The MIC4102 monitors the LO pin voltage and prevents the HO pin from turning on until the voltage on the LO pin reaches the VLOOFF threshold. After a short delay, the MIC4102 drives the HO pin high. Monitoring the LO voltage eliminates any excessive delay due to the MOSFET drivers turn-off time and the short delay accounts for the MOSFET turn-off delay as well as letting the LO pin voltage settle out. An external resistor between the LO output and the MOSFET may affect the performance of the LO pin monitoring circuit and is not recommended. A low on the PWM pin causes the HO pin to go low after a short delay (THOOFF). Before the LO pin can go high, 13 M9999-112806 Micrel, Inc. MIC4102 the voltage on the switching node (HS pin) must have dropped to 2.5V below the Vdd voltage. Monitoring the switch voltage instead of the HO pin voltage eliminates timing variations and excessive delays due to the high side MOSFET turn-off. The LO driver turns on after a short delay (TLOON). Once the LO driver is turn on, it is latched on until the PWM signal goes high. This prevents any ringing or oscillations on the switch node or HS pin from turning off the LO driver. If the PWM pin goes low and the voltage on the HS pin does not cross the VSWth threshold, the LO pin will be forced high after a short delay (TSWTO), insuring proper operation. Fast propagation delay between the input and output drive waveform is desirable. It improves overcurrent protection by decreasing the response time between the control signal and the MOSFET gate drive. Minimizing propagation delay also minimizes phase shift errors in power supplies with wide bandwidth control loops. Care must be taken to insure the input signal pulse width is greater than the minimum specified pulse width. An input signal that is less than the minimum pulse width may result in no output pulse or an output pulse whose width is significantly less than the input. The maximum duty cycle (ratio of high side on-time to switching period) is determined by the time required for the CB capacitor to charge during the off-time. Adequate time must be allowed for the CB capacitor to charge up before the high-side driver is turned back on. The anti-shoot-through circuit in the MIC4102 prevents the driver from turning both MOSFETs on at the same time, however, other factors outside of the anti-shootthrough circuit's control can cause shoot-through. Some of these are ringing on the gate drive node and capacitive coupling of the switching node voltage on the gate of the low-side MOSFET. and the voltage derating used for reliability. 25V rated X5R or X7R ceramic capacitors are recommended for most applications. The minimum capacitance value should be increased if low voltage capacitors are use since even good quality dielectric capacitors, such as X5R, will lose 40% to 70% of their capacitance value at the rated voltage. Placement of the decoupling capacitors is critical. The bypass capacitor for Vdd should be placed as close as possible between the Vdd and Vss pins. The bypass capacitor (CB) for the HB supply pin must be located as close as possible between the HB and HS pins. The etch connections must be short, wide and direct. The use of a ground plane to minimize connection impedance is recommended. Refer to the section on layout and component placement for more information. The voltage on the bootstrap capacitor drops each time it delivers charge to turn on the MOSFET. The voltage drop depends on the gate charge required by the MOSFET. Most MOSFET specifications specify gate charge vs. Vgs voltage. Based on this information and a recommended VHB of less than 0.1V, the minimum value of bootstrap capacitance is calculated as: CB VHB where : Q gate = Total Gate Charge at VHB HB = Voltage drop at the HB pin The decoupling capacitor for the Vdd input may be calculated in with the same formula, however, the two capacitors are usually equal in value. Grounding, Component Placement and Circuit Layout Nanosecond switching speeds and ampere peak currents in and around the MIC4102 driver require proper placement and trace routing of all components. Improper placement may cause degraded noise immunity, false switching, excessive ringing or circuit latch-up. Figure 9 shows the critical current paths when the driver outputs go high and turn on the external MOSFETs. It also shown the need for a low impedance ground plane. Charge needed to turn-on the MOSFET gates comes from the decoupling capacitors CVDD and CB. Current in the low-side gate driver flows from CVDD through the internal driver, into the MOSFET gate and out the Source. The return connection back to the decoupling capacitor is made through the ground plane. Any inductance or resistance in the ground return path causes a voltage spike or ringing to appear on the source of the MOSFET. This voltage works against the gate voltage and can either slow down or turn off the MOSFET during the period where it should be turned on. Decoupling and Bootstrap Capacitor Selection Decoupling capacitors are required for both the low side (Vdd) and high side (HB) supply pins. These capacitors supply the charge necessary to drive the external MOSFETs as well as minimize the voltage ripple on these pins. The capacitor from HB to HS serves double duty by providing decoupling for the high-side circuitry as well as providing current to the high-side circuit while the high-side external MOSFET is on. Ceramic capacitors are recommended because of their low impedance and small size. Z5U type ceramic capacitor dielectrics are not recommended due to the large change in capacitance over temperature and voltage. A minimum value of 0.1uf is required for each of the capacitors, regardless of the MOSFETs being driven. Larger MOSFETs may require larger capacitance values for proper operation. The voltage rating of the capacitors depends on the supply voltage, ambient temperature November 2006 Qgate 14 M9999-112806 Micrel, Inc. MIC4102 Current in the high-side driver is sourced from capacitor CB and flows into the HB pin and out the HO pin, into the gate of the high side MOSFET. The return path for the current is from the source of the MOSFET and back to capacitor CB. The high-side circuit return path usually does not have a low impedance ground plane so the etch connections in this critical path should be short and wide to minimize parasitic inductance. As with the lowside circuit, impedance between the MOSFET source and the decoupling capacitor causes negative voltage feedback which fights the turn-on of the MOSFET. It is important to note that capacitor CB must be placed close to the HB and HS pins. This capacitor not only provides all the energy for turn-on but it must also keep HB pin noise and ripple low for proper operation of the high-side drive circuitry. Low-side drive turn-off current path CVdd Charge CB through internal diode when HS pin is low gnd plane CVdd LO HB Vss CB CB High-side drive turn-on current path FF Q HS Q PWM Level shift HS LS Figure 10. Turn-off Current Paths The following circuit guidelines should be adhered to for optimum circuit performance: 1. The Vcc and HB bypass capacitors must be placed close to the supply and ground pins. It is critical that the etch length between the high side decoupling capacitor (CB) and the HB & HS pins be minimized to reduce lead inductance. 2. A ground plane should be used to minimize parasitic inductance and impedance of the return paths. The MIC4102 is capable of greater than 3A peak currents and any impedance between the MIC4102, the decoupling capacitors and the external MOSFET will degrade the performance of the driver. 3. Trace out the high di/dt and dv/dt paths, as shown in Figures 9 and 10 to minimize the etch length and loop area for these connections. Minimizing these parameters decreases the parasitic inductance and the radiated EMI generated by fast rise and fall times. A typical layout of a synchronous Buck converter power stage using the MIC4102 (Figure 11) is shown in Figure 12. PWM Level shift LS Figure 9. Turn-on Current Paths Figure 10 shows the critical current paths when the driver outputs go low and turn off the external MOSFETs. Short, low impedance connections are important during turn-off for the same reasons given in the turn-on explanation. Current flowing through the internal diode replenishes charge in the bootstrap capacitor, CB. November 2006 FF HO High-side drive turn-off current path gnd plane _ Q HO Vss HB _ Q Low-side drive turn-on current path Vdd LO Vdd 15 M9999-112806 Micrel, Inc. MIC4102 F Figure 11. Typical Converter Power Stage Figure 12. Typical Layout of a Synchronous Buck Converter Power Stage 1. The circuit is configured as a synchronous buck power stage. The high-side MOSFET drain connects to the input supply voltage (drain) and the source connects to the switching node. The low-side MOSFET drain connects to the switching node and its source is connected to ground. The buck converter output inductor (not shown) would connect to the switching node. The high-side drive trace, HO, is routed on top of its return trace, HS, to minimize loop area and parasitic inductance. The low-side drive trace, November 2006 LO is routed over the ground plane which minimizes the impedance of that current path. The decoupling capacitors, CB and CVDD are placed to minimize etch length between the capacitors and their respective pins. This close placement is necessary to efficiently charge capacitor CB when the HS node is low. All traces are 0.025" wide or greater to reduce impedance. Cin is used to decouple the high current path through the MOSFETs. 16 M9999-112806 Micrel, Inc. MIC4102 Package Information 8-Pin SOIC (M) MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http:/www.micrel.com The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser's use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser's own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. (c) 2006 Micrel, Incorporated. November 2006 17 M9999-112806