PAA140 Dual Single-Pole, Normally Open OptoMOS(R) Relays Parameter Load Voltage Load Current Max RON Rating 400 250 8 Description Units V mA The PAA140 is a 400V, 250mA, 8, dual normally open (1-Form-A) relay. This high performance leader provides a high peak load voltage handling capability combined with a very low on-resistance for specialized applications. Features * 3750Vrms Input/Output Isolation * Small 8-Pin Package * Low Drive Power Requirements (TTL/CMOS Compatible) * No Moving Parts * High Reliability * Arc-Free With No Snubbing Circuits * No EMI/RFI Generation * Machine Insertable, Wave Solderable * Tape & Reel Versions Available Approvals * UL Recognized Component: File E76270 * CSA Certified Component: Certificate 1175739 * EN/IEC 60950-1 Certified Component: TUV Certificate B 09 07 49410 004 Ordering Information Applications * Telecommunications * Telecom Switching * Tip/Ring Circuits * Modem Switching (Laptop, Notebook, Pocket Size) * Hook Switch * Dial Pulsing * Ground Start * Ringing Injection * Instrumentation * Multiplexers * Data Acquisition * Electronic Switching * I/O Subsystems * Meters (Watt-Hour, Water, Gas) * Medical Equipment-Patient/Equipment Isolation * Security * Aerospace * Industrial Controls Part # PAA140 PAA140P PAA140PTR PAA140S PAA140STR Description 8-Lead DIP (50/tube) 8-Lead Flatpack (50/tube) 8-PLead Flatpack (1000/Reel) 8-Lead Surface Mount (50/tube) 8-Lead Surface Mount (1000/Reel) Pin Configuration + Control - Switch #1 - Control - Switch #1 + Control - Switch #2 - Control - Switch #2 1 8 2 7 3 6 4 5 Load - Switch #1 Load - Switch #1 Load - Switch #2 Load - Switch #2 Switching Characteristics of Normally Open Devices Form-A IF 90% 10% ILOAD ton Pb RoHS 2002/95/EC DS-PAA140-R08 toff e3 www.clare.com 1 PAA140 Absolute Maximum Ratings @ 25C Parameter Blocking Voltage Reverse Input Voltage Input Control Current Peak (10ms) Input Power Dissipation 1 Total Power Dissipation 2 Isolation Voltage, Input to Output Operational Temperature Storage Temperature 1 Derate linearly 1.33 mW / C 2 Derate linearly 6.67 mW / C Ratings 400 5 50 1 150 800 3750 -40 to +85 -40 to +125 Absolute Maximum Ratings are stress ratings. Stresses in excess of these ratings can cause permanent damage to the device. Functional operation of the device at conditions beyond those indicated in the operational sections of this data sheet is not implied. Units VP V mA A mW mW Vrms C C Electrical Characteristics @ 25C Parameter Output Characteristics Load Current Continuous * Peak On-Resistance Off-State Leakage Current Switching Speeds Turn-On Turn-Off Input Characteristics Input Control Current Input Dropout Current Input Voltage Drop Reverse Input Current Common Characteristics Capacitance Input to Output Conditions Symbol Min Typ Max Units t=10ms IL=250mA VL=400VP IL ILPK RON ILEAK - 6 - 250 500 8 1 IF=5mA, VL=10V ton toff - - 3 1 ms IL=250mA IF=5mA VR=5V IF IF VF IR 0.4 0.9 - 0.7 1.2 - 5 1.4 10 mA mA V A - CI/O - 3 - pF mA A *NOTE: If both poles operate simultaneously, then load current must be derated so that the package power dissipation value is not exceeded. 2 www.clare.com R08 PAA140 PERFORMANCE DATA* 25 15 10 5 0 0.91 1.17 1.43 1.69 10 5 25 20 15 10 5 0 5.03 5.38 5.73 6.08 6.43 6.78 7.13 Turn-On (ms) Turn-Off (ms) On-Resistance () Typical IF for Switch Operation (N=50, IL=250mADC, TA=25C) Typical IF for Switch Dropout (N=50, IL=250mADC, TA=25C) Typical Blocking Voltage Distribution (N=50, TA=25C) 25 15 10 5 35 30 20 Device Count (N) 20 15 10 5 2.1 2.7 3.3 3.9 4.5 25 20 15 10 5 0 0 1.5 0.9 5.1 1.5 2.1 2.7 3.3 3.9 430 4.5 442 454 466 478 490 LED Current (mA) LED Current (mA) Blocking Voltage (VP) Typical LED Forward Voltage Drop (N=50, IF=5mA, TA=25C) Typical Turn-On vs. LED Forward Current (IL=250mADC) Typical Turn-Off vs. LED Forward Current (IL=250mADC) Turn-On (ms) 25 20 15 10 5 0 1.17 1.19 1.21 1.23 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 Turn-Off (ms) 30 0 1.25 5 10 15 20 25 30 35 40 45 0.050 0.045 0.040 0.035 0.030 0.025 0.020 0.015 0.010 0.005 0 50 0 5 10 15 20 25 30 35 40 502 45 LED Forward Voltage Drop (V) LED Forward Current (mA) LED Forward Current (mA) Typical LED Forward Voltage Drop vs. Temperature Typical Turn-On vs. Temperature (IL=250mADC) Typical Turn-Off vs. Temperature (IF=5mA, IL=250mADC) 2.5 1.6 2.0 1.4 IF=50mA IF=30mA IF=20mA IF=10mA IF=5mA 1.2 1.0 Turn-On (ms) 1.8 0.07 1.5 1.0 0.5 -40 -20 0 20 40 60 Temperature (C) 80 100 120 0.05 0.04 0.03 0.02 0.01 0 0.8 50 0.06 I F = 5mA I F = 10mA I F = 20mA Turn-Off (ms) Device Count (N) 15 0.018 0.030 0.042 0.054 0.066 0.078 0.090 0 LED Forward Voltage Drop (V) 30 20 1.95 Device Count (N) Device Count (N) 25 0.65 Typical On-Resistance Distribution (N=50, IF=5mA, IL=250mADC, TA=25C) 35 0 0.39 35 Typical Turn-Off Time (N=50, IF=5mA, IL=250mADC, TA=25C) Device Count (N) 20 Device Count (N) Device Count (N) 25 Typical Turn-On Time (N=50, IF=5mA, IL=250mADC, TA=25C) 0 -40 -20 0 20 40 60 Temperature (C) 80 100 -40 -20 0 20 40 60 80 100 Temperature (C) *The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application department. R08 www.clare.com 3 PAA140 PERFORMANCE DATA* Typical IF for Switch Operation vs. Temperature (IL=250mADC) 5.0 5.0 3.5 3.0 2.5 9 On-Resistance () LED Current (mA) 4.0 3.5 3.0 2.5 8 7 6 5 2.0 2.0 1.5 1.5 -40 -20 0 20 40 60 80 4 -40 100 -20 0 20 40 60 80 100 -40 -20 0 20 40 60 Temperature (C) Temperature (C) Temperature (C) Typical Load Current vs. Load Voltage (IF=5mA, TA=25C) Typical Load Current vs. Temperature Typical Blocking Voltage vs. Temperature 350 Load Current (mA) 250 200 150 100 50 0 -50 -100 -150 -200 -250 -2.0 -1.5 80 100 80 100 485 300 250 I F = 20mA I F = 10mA I F = 5mA 200 150 Blocking Voltage (VP) LED Current (mA) 4.0 Typical On-Resistance vs. Temperature (IF=5mA, IL=250mADC) 10 4.5 4.5 Load Current (mA) Typical IF for Switch Dropout vs. Temperature (IL=250mADC) 480 475 470 465 460 455 450 100 -1.0 -0.5 0 0.5 1.0 1.5 445 -40 2.0 -20 0 Load Voltage (V) 20 40 60 120 -40 -20 0 1.2 0.10 1.0 0.08 0.06 0.04 20 40 60 Temperature (C) Energy Rating Curve 0.12 Load Current (A) Leakage (A) 100 Temperature (C) Typical Leakage vs. Temperature Measured Across Pins 5&6 or 7&8 0.8 0.6 0.4 0.2 0.02 0 80 -40 -20 0 20 40 60 80 100 0 10s 100s 1ms 10ms 100ms 1s 10s 100s Time Temperature (C) *The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application department. 4 www.clare.com R08 PAA140 Manufacturing Information Moisture Sensitivity All plastic encapsulated semiconductor packages are susceptible to moisture ingression. Clare classified all of its plastic encapsulated devices for moisture sensitivity according to the latest version of the joint industry standard, IPC/JEDEC J-STD-020, in force at the time of product evaluation. We test all of our products to the maximum conditions set forth in the standard, and guarantee proper operation of our devices when handled according to the limitations and information in that standard as well as to any limitations set forth in the information or standards referenced below. Failure to adhere to the warnings or limitations as established by the listed specifications could result in reduced product performance, reduction of operable life, and/or reduction of overall reliability. This product carries a Moisture Sensitivity Level (MSL) rating as shown below, and should be handled according to the requirements of the latest version of the joint industry standard IPC/JEDEC J-STD-033. Device Moisture Sensitivity Level (MSL) Rating PAA140 / PAA140S / PAA140P MSL 1 ESD Sensitivity This product is ESD Sensitive, and should be handled according to the industry standard JESD-625. Reflow Profile This product has a maximum body temperature and time rating as shown below. All other guidelines of J-STD-020 must be observed. Device Maximum Temperature x Time PAA140 / PAA140S 250C for 30 seconds PAA140P 260C for 30 seconds Board Wash Clare recommends the use of no-clean flux formulations. However, board washing to remove flux residue is acceptable. Since Clare employs the use of silicone coating as an optical waveguide in many of its optically isolated products, the use of a short drying bake could be necessary if a wash is used after solder reflow processes. Chlorine-based or Fluorine-based solvents or fluxes should not be used. Cleaning methods that employ ultrasonic energy should not be used. Pb R08 RoHS 2002/95/EC e3 www.clare.com 5 PAA140 MECHANICAL DIMENSIONS PAA140 2.540 0.127 (0.100 0.005) 9.652 0.381 (0.380 0.015) PCB Hole Pattern 7.620 0.254 (0.300 0.010) 8-0.800 DIA. (8-0.031 DIA.) 2.540 0.127 (0.100 0.005) 9.144 0.508 (0.360 0.020) 6.350 0.127 (0.250 0.005) 6.350 0.127 (0.250 0.005) 3.302 0.051 (0.130 0.002) 0.457 0.076 (0.018 0.003) 7.239 TYP. (0.285) 4.064 TYP (0.160) 0.254 TYP (0.01) 7.620 0.127 (0.300 0.005) 7.620 0.127 (0.300 0.005) Dimensions mm (inches) 0.889 0.102 (0.035 0.004) PAA140S 9.652 0.381 (0.380 0.015) 2.540 0.127 (0.100 0.005) 6.350 0.127 (0.250 0.005) 0.635 0.127 (0.025 0.005) 3.302 0.051 (0.130 0.002) 9.525 0.254 (0.375 0.010) 0.457 0.076 (0.018 0.003) PCB Land Pattern 2.54 (0.10) 8.90 (0.3503) 1.65 (0.0649) 7.620 0.254 (0.300 0.010) 0.254 0.127 (0.010 0.0005) 0.65 (0.0255) 4.445 0.127 (0.175 0.005) Dimensions mm (inches) 0.813 0.120 (0.032 0.004) PAA140P 2.540 0.127 (0.100 0.005) 6.350 0.127 (0.250 0.005) 0 MIN / 0.102 MAX (0 MIN / 0.004 MAX) 9.398 0.127 (0.370 0.005) 9.652 0.381 (0.380 0.015) 7.620 0.254 (0.300 0.010) 2.286 MAX. (0.090 MAX.) 2.54 (0.10) 0.635 0.127 (0.025 0.005) 0.203 0.013 (0.008 0.0005) 8.70 (0.3425) 1.55 (0.0610) 0.65 (0.0255) 2.159 0.025 (0.085 0.001) 0.457 0.076 (0.018 0.003) 0.864 0.120 (0.034 0.004) 6 PCB Land Pattern Dimensions mm (inches) www.clare.com R08 PAA140 MECHANICAL DIMENSIONS PAA140S Tape & Reel 330.2 DIA. (13.00 DIA.) Top Cover Tape Thickness 0.102 MAX. (0.004 MAX.) W=16.00 (0.63) Bo=10.30 (0.406) K0 =4.90 (0.193) Ao=10.30 (0.406) K1 =4.20 (0.165) Embossed Carrier Embossment P=12.00 (0.472) User Direction of Feed Dimensions mm (inches) NOTES: 1. Dimensions carry tolerances of EIA Standard 481-2 2. Tape complies with all "Notes" for constant dimensions listed on page 5 of EIA-481-2 PAA140P Tape & Reel 330.2 DIA. (13.00 DIA.) W = 16.00 (0.63) Top Cover Tape Thickness 0.102 MAX. (0.004 MAX.) Bo = 10.30 (0.406) K0 = 2.70 (0.106) K1 = 2.00 (0.079) Embossed Carrier Embossment P = 12.00 (0.472) User Direction of Feed Ao = 10.30 (0.406) Dimensions mm (inches) NOTES: 1. All dimensions carry tolerances of EIA Standard 481-2 2. The tape complies with all "Notes" for constant dimensions listed on page 5 of EIA-481-2 For additional information please visit our website at: www.clare.com Clare, Inc. makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any time without notice. Neither circuit patent licenses nor indemnity are expressed or implied. Except as set forth in Clare's Standard Terms and Conditions of Sale, Clare, Inc. assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right. The products described in this document are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body, or in other applications intended to support or sustain life, or where malfunction of Clare's product may result in direct physical harm, injury, or death to a person or severe property or environmental damage. Clare, Inc. reserves the right to discontinue or make changes to its products at any time without notice. 7 Specification: DS-PAA140-R08 (c)Copyright 2010, Clare, Inc. OptoMOS(R) is a registered trademark of Clare, Inc. All rights reserved. Printed in USA. 7/30/2010