SiC417 Vishay Siliconix microBUCKTM SiC417 10-A, 28-V Integrated Buck Regulator with Programmable LDO DESCRIPTION FEATURES The Vishay Siliconix SiC417 is an advanced stand-alone synchronous buck regulator featuring integrated power MOSFETs, bootstrap diode, and a programmable LDO in a space-saving MLPQ 5 x 5 - 32 pin package. The SiC417 is capable of operating with all ceramic solutions and switching frequencies up to 1 MHz. The programmable frequency, synchronous operation and selectable power-save allow operation at high efficiency across the full range of load current. The internal programmable LDO may be used to supply 5 V for the gate drive circuits or it may be bypassed with an external 5 V for optimum efficiency and used to drive external N-channel MOSFETs or other loads. Additional features include cycle-by-cycle current limit, voltage soft-start, under-voltage protection, programmable over-current protection, soft shutdown and selectable power-save. The Vishay Siliconix SiC417 also provides an enable input and a power good output. * High efficiency > 92 % * Internal power MOSFETs: High-side RDS(ON) = 27 m Low-side RDS(ON) = 9 m * Integrated bootstrap diode * Integrated configurable 150 mA LDO with bypass logic * Temperature compensated current limit * Pseudo fixed-frequency adaptive on-time control * All ceramic solution enabled * Programmable input UVLO threshold * Independent enable pin for switcher and LDO * Selectable ultra-sonic power-save mode * Internal soft-start and soft-shutdown * 1 % internal reference voltage * Power good output and over voltage protection * Halogen-free according to IEC 61249-2-21 definition * Compliant to RoHS directive 2002/95/EC PRODUCT SUMMARY Input Voltage Range 3 V to 28 V APPLICATIONS Output Voltage Range 0.5 V to 5.5 V Operating Frequency 200 kHz to 1 MHz Continuous Output Current Peak Efficiency * * * * * * 10 A 95 % at 300 kHz Package MLPQ 5 mm x 5 mm Notebook, desktop and server computers Digital HDTV and digital consumer applications Networking and telecommunication equipment Printers, DSL and STB applications Embedded applications Point of load power supplies TYPICAL APPLICATION CIRCUIT 3 7 2 EN-PSAVE 29 PGOOD 26 EN-LDO 32 31 Document Number: 69062 S10-1367-Rev. D, 14-Jun-10 DH V5V 12 VIN 6 BST 8 VLDO FBL EN/PSV PGOOD LX 13 PWM Controller 27 ILIM 15 ENL tON AGND 30 1 FB DL 14 PGND 5 VOUT www.vishay.com 1 SiC417 Vishay Siliconix LX PGOOD ILIM LX EN/PSV AGND tON ENL PIN CONFIGURATION LX FB PAD 1 FBL LX AGND 34 V5V PGND AGND VOUT PAD 3 PGND LX 33 PGND VIN PAD 2 PGND VLDO VIN 35 PGND BST PGND PGND LX DL DH VIN VIN VIN PGND PIN DESCRIPTION Pin Number Symbol 1 FB 2 FBL 3 V5V 4, 30, PAD 1 AGND Description Feedback input for switching regulator. Connect to an external resistor divider from output to program the output voltage. Feedback input for the LDO. Connect to an external resistor divider from VLDO to program the VLDO output. 5 V power input for internal analog circuits and gate drives. Connect to external 5 V supply or configure the LDO for 5 V and connect to VLDO . Analog ground. 5 VOUT Output voltage input to the SiC417. Additionally, may be used to bypass LDO to supply VLDO directly. 6, 9 - 11, PAD 2 VIN 7 VLDO 8 BST 12 DH LDO output. Bootstrap pin. A capacitor is connected between BST to LX to develop the floating voltage for the high-side gate drive. High-side gate drive - do not connect this pin. 14 13, 23 - 25, 28, PAD 3 15-22 DL Low-side gate drive - do not connect this pin. LX Switching (Phase) node. PGND 26 PGOOD 27 ILIM 29 EN/PSV Input supply voltage. 31 tON Power ground. Open-drain power good indicator. High impedance indicates power is good. An external pull-up resistor is required. Current limit sense point - to program the current limit connect a resistor from ILIM to LX. Tri-state pin. Enable input for switching regulator. Connect EN to AGND to disable the switching regulator. Float pin for forced continuous and pull high for power-save mode. On-time set input. Set the on-time by a series resistor to the input supply voltage. 32 ENL Enable input for the LDO. Connect ENL to AGND to disable the LDO. ORDERING INFORMATION www.vishay.com 2 Part Number SiC417CD-T1-E3 Package MLPQ55-32 SiC417DB Evaluation board Document Number: 69062 S10-1367-Rev. D, 14-Jun-10 SiC417 Vishay Siliconix FUNCTIONAL BLOCK DIAGRAM 3 V5V 6, 9 - 11 PAD 3 VIN VIN 29 26 PGD V5V EN/PSV AGND 1.20.21 PAD 1 V5V Reference BST Control and Status 8 DL Soft Start + FB 1 Gate Drive Control tON 31 VOUT 5 LX 13, 23 - 25 28, PAD 3 V5V PGND FB Comparator 15-22 Zero Cross Detector Bypass Comparator ILIM Valley 1 - Limit VLDO 7 A Y B FBL 27 VIN LDO MUX 2 32 ENL ABSOLUTE MAXIMUM RATINGS TA = 25 C, unless otherwise noted Parameter Symbol Min. Max. LX to PGND Voltage VLX - 0.3 + 30 LX to PGND Voltage (transient - 100 ns) VLX -2 + 30 VIN to PGND Voltage VIN - 0.3 + 30 VEN Maximum Voltage VEN - 0.3 VIN BST Bootstrap to LX; V5V to PGND - 0.3 + 6.0 AGND to PGND - 0.3 + 0.3 EN/PSV, PGOOD, ILIM, VOUT, VLDO, FB, FBL to GND - 0.3 + (V5V + 0.3) tON to PGND - 0.3 + (V5V - 1.5) BST to PGND - 0.3 + 35 VAG-PG Unit V Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating/conditions for extended periods may affect device reliability. RECOMMENDED OPERATING CONDITIONS Parameter Symbol Min. VIN 3.0 28 V5V to PGND V5V 4.5 5.5 VOUT to PGND VOUT 0.5 5.5 Input Voltage Typ. Max. Unit V Note: For proper operation, the device should be used within the recommended conditions. THERMAL RESISTANCE RATINGS Parameter Storage Temperature Symbol Min. Typ. Max. TSTG - 40 + 150 Maximum Junction Temperature TJ - 150 Operation Junction Temperature TJ - 25 + 125 Document Number: 69062 S10-1367-Rev. D, 14-Jun-10 Unit C www.vishay.com 3 SiC417 Vishay Siliconix THERMAL RESISTANCE RATINGS Thermal Resistance, Junction-to-Ambientb High-Side MOSFET Low-Side MOSFET PWM Controller and LDO Thermal Resistance 25 20 50 C/W Peak IR Reflow Temperature TReflow 260 C Notes: a. This device is ESD sensitive. Use of standard ESD handling precautions is required. b. Calculated from package in still air, mounted to 3 x 4.5 (in), 4 layer FR4 PCB with thermal vias under the exposed pad per JESD51 standards. Exceeding the above specifications may result in permanent damage to the device or device malfunction. Operation outside of the parameters specififed in the Electrical Characteristicsw section is not recommended. ELECTRICAL SPECIFICATIONS Parameter Symbol Test Conditions Unless Specified VIN = 12 V, V5V = 5 V, TA = + 25 C for typ., - 25 C to + 85 C for min. and max., TJ = < 125 C Min. Typ. Max. Unit Input Supplies VIN Input Voltage VIN 3 28 V5V Voltage V5V 4.5 5.5 VIN UVLO Threshold Voltagea VIN UVLO Hysteresis V5V UVLO Threshold Voltage V5V UVLO Hysteresis VIN Supply Current V5V Supply Current VIN_UV+ Sensed at ENL pin, rising edge 2.4 2.6 2.95 VIN_UV- Sensed at ENL pin, falling edge 2.235 2.4 2.565 VIN_UV_HY EN/PSV = High 0.2 V5V_UV+ Measured at V5V pin, rising edge 3.7 3.9 4.1 V5V_UV- Measured at V5V pin, falling edge 3.5 3.6 3.75 0.3 V5V_UV_HY IIN I5V V EN/PSV, ENL = 0 V, VIN = 28 V 8.5 Standby mode: ENL = V5V, EN/PSV = 0 V 130 EN/PSV, ENL = 0 V 3 EN/PSV = V5V, no load (fSW = 25 kHz), VFB > 500 mVb 20 A 7 2 b fSW = 250 kHz, EN/PSV = floating, no load mA 10 Controller FB On-Time Threshold VFB-TH Static VIN and load, - 40 C to + 85 C 0.495 Frequency Range FPWM continuous mode 200 Bootstrap Switch Resistance 0.5 0.505 V 1000 kHz 10 Timing Continuous mode operation VIN = 15 V, VOUT = 5 V, fSW = 300 kHz, Rton = 133 k 999 1110 On-Time tON Minimum On-Timeb tON 50 Minimum Off-Timeb tOFF 250 1220 ns Soft Start Soft Start Timeb tSS IOUT = ILIM/2 0.85 ms 500 k Analog Inputs/Outputs VOUT Input Resistance RO-IN Current Sense Zero-Crossing Detector Threshold Voltage VSense-th LX-PGND -3 - 10 % 0 +3 mV Power Good PG_VTH Internal reference 500 mV Start-Up Delay Time PG_Td VEN = 0 V 2 Fault (noise-immunity) Delay Timeb PG_ICC VEN = 0 V 5 Power Good Leakage Current PG_ILK VEN = 0 V PG_RDS-ON VEN = 0 V Power Good Threshold Voltage Power Good On-Resistance www.vishay.com 4 + 20 % s 1 10 V ms A Document Number: 69062 S10-1367-Rev. D, 14-Jun-10 SiC417 Vishay Siliconix ELECTRICAL SPECIFICATIONS Test Conditions Unless Specified VIN = 12 V, V5V = 5 V, TA = + 25 C for typ., - 25 C to + 85 C for min. and max., TJ = < 125 C Min. RILIM = 5.9 k 6 8 10 A VILM-LK With respect to AGND - 10 0 + 10 mV Output Under-Voltage Fault VOUV_Fault VFB with respect to Internal 500 mV reference, 8 consecutive clocks - 25 Smart Power-Save Protection Threshold Voltageb PSAVE_VTH VFB with respect to internal 500 mV reference + 10 VFB with respect to internal 500 mV reference + 20 5 s 10 C hysteresis 150 C Parameter Symbol Typ. Max. Unit Fault Protection ILIM Source Current ILIM 10 Valley Current Limit ILIM Comparator Offset Voltage Over-Voltage Protection Threshold Over-Voltage Fault Delayb tOV-Delay Over Temperature Shutdownb TShut A % % Logic Inputs/Outputs Logic Input High Voltage VIN+ Logic Input Low Voltage VIN- EN/PSV Input Bias Current IEN- 2 EN, ENL, PSV 0.4 EN/PSV = V5V or AGND - 10 VIN = 28 V ENL Input Bias Current FBL, FB Input Bias Current FBL_ILK + 10 11 FBL, FB = V5V or AGND -1 VLDO load = 10 mA 0.735 V 18 A +1 Linear Dropout Regulator FBL Accuracy FBLACC LDO Current Limit Start-up and foldback, VIN = 12 V LDO_ILIM Operating current limit, VIN = 12 V 0.75 0.765 85 135 mA 200 VLDO to VOUT Switch-Over Thresholdc VLDO-BPS - 140 + 140 VLDO to VOUT Non-Switch-Over Thresholdc VLDO-NBPS - 450 + 450 VLDO to VOUT Switch-Over Resistance LDO Drop Out Voltage mV VOUT = 5 V 2 From VIN to VVLDO, VVLDO = + 5 V, IVLDO = 100 mA 1.2 V RLDO d V Notes: a. VIN UVLO is programmable using a resistor divider from VIN to ENL to AGND. The ENL voltage is compared to an internal reference. b. Guaranteed by design. c. The switch-over threshold is the maximum voltage diff erential between the VLDO and VOUT pins which ensures that VLDO will internally switch-over to VOUT. The non-switch-over threshold is the minimum voltage diff erential between the VLDO and VOUT pins which ensures that VLDO will not switch-over to VOUT. d. The LDO drop out voltage is the voltage at which the LDO output drops 2 % below the nominal regulation point. ELECTRICAL CHARACTERISTICS 100 95 VIN = 9 V 90 VIN = 19 V Efficiency (%) 85 80 75 70 65 60 55 50 0 1 2 3 4 5 6 7 8 9 10 IOUT (A) Efficiency vs. Output Current (VOUT = 1.2 V) Document Number: 69062 S10-1367-Rev. D, 14-Jun-10 www.vishay.com 5 SiC417 Vishay Siliconix ELECTRICAL CHARACTERISTICS 1.35 300 250 1.3 VIN = 19 V 200 VOUT (V) Frequency (kHz) VIN = 9 V 150 VIN = 9 V 1.25 VIN = 19 V 100 1.2 50 0 1.15 0 1 2 3 4 5 6 7 8 9 10 IOUT (A) Frequency vs. IOUT, (VOUT = 1.2 V) 0 1 2 3 4 5 6 7 8 9 10 IOUT (A) Load Regulation, (VOUT = 1.2 V) Start up Time: VIN = 12 V, VOUT = 1.2 V, IOUT = 0 A PGOOD Delay after Start up Time: VIN = 12 V, VOUT = 1.2 V, IOUT = 0 A Transient Response: VIN = 12 V, VOUT = 1.2 V, IOUT = 10 A to 5 A, dI/dt = 0.5 A/s Transient Response: VIN = 12 V, VOUT = 1.2 V, IOUT = 5 A to 10 A, dI/dt = 0.5 A/s www.vishay.com 6 Document Number: 69062 S10-1367-Rev. D, 14-Jun-10 SiC417 Vishay Siliconix ELECTRICAL CHARACTERISTICS Ultra-Sonic Power-Save at IOUT = 0 A Over Current Protection: VIN = 12 V, VOUT = 1.2 V APPLICATIONS INFORMATION SiC417 Synchronous Buck Converter The SiC417 is a step down synchronous buck dc-to-dc converter with integrated power FETs and programmable LDO. The SiC417 is capable of 10 A operation at very high efficiency in a tiny 5 mm x 5 mm - 32 pin package. The programmable operating frequency range of 200 kHz to 1 MHz, enables the user to optimize the solution for minimum board space and optimum efficiency. The buck controller employs pseudo-fixed frequency adaptive on-time control. This control scheme allows fast transient response thereby lowering the size of the power components used in the system. tON VIN VLX CIN VFB Q1 VLX FB threshold VOUT L Q2 ESR FB + Input Voltage Range The SiC417 requires two input supplies for normal operation: VIN and V5V. VIN operates over the wide range from 3 V to 28 V. V5V requires a 5 V supply input that can be an external source or the internal LDO configured to supply 5 V. When VIN is less than ~ 6 V then an external 5 V supply must be tied to V5V. Pseudo-Fixed Frequency Adaptive On-Time Control The PWM control method used for the SiC417 is pseudo-fixed frequency, adaptive on-time, as shown in figure 1. The ripple voltage generated at the output capacitor ESR is used as a PWM ramp signal. This ripple is used to trigger the on-time of the controller. The adaptive on-time is determined by an internal oneshot timer. When the one-shot is triggered by the output ripple, the device sends a single on-time pulse to the highside MOSFET. The pulse period is determined by VOUT and VIN; the period is proportional to output voltage and inversely proportional to input voltage. With this adaptive on-time arrangement, the device automatically anticipates the on-time needed to regulate VOUT for the present VIN condition and at the selected frequency. Document Number: 69062 S10-1367-Rev. D, 14-Jun-10 COUT Figure 1 - Output Ripple and PWM Control Method The adaptive on-time control has significant advantages over traditional control methods used in the controllers today. * Reduced component count by eliminating DCR sense or current sense resistor as no need of a sensing inductor current. * Reduced Saves external components used for compensation by eliminating the no error amplifier and other components. * Ultra fast transient response because of fast loop, absence of error amplifier speeds up the transient response. * Predictable frequency spread because of constant on-time architecture. * Fast transient response enables operation with minimum output capacitance Overall, superior performance compared to fixed frequency architectures. www.vishay.com 7 SiC417 Vishay Siliconix On-Time One-Shot Generator (tON) and Operating Frequency The SiC417 have an internal on-time one-shot generator which is a comparator that has two inputs. The FB Comparator output goes high when VFB is less than the internal 500 mV reference. This feeds into the gate drive and turns on the high-side MOSFET, and also starts the one-shot timer. The one-shot timer uses an internal comparator and a capacitor. One comparator input is connected to VOUT, the other input is connected to the capacitor. When the on-time begins, the internal capacitor charges from zero volts through a current which is proportional to VIN. When the capacitor voltage reaches VOUT, the on-time is completed and the high-side MOSFET turns off. The figure 2 shows the on-chip implementation of on-time generation. FB comparator FB 500 mV + VOUT VIN Rton DH Q1 VLX DL Q2 VOUT L ESR COUT FB + On-time = K x Rton x (VOUT/VIN) Figure 2 - On-Time Generation This method automatically produces an on-time that is proportional to VOUT and inversely proportional to VIN. Under steady-state conditions, the switching frequency can be determined from the on-time by the following equation. fSW = VOUT tON x VIN The SiC417 uses an external resistor to set the ontime which indirectly sets the frequency. The on-time can be programmed to provide operating frequency from 200 kHz to 1 MHz using a resistor between the tON pin and ground. The resistor value is selected by the following equation. (t - 10 ns) x VIN Rton = ON 25 pF x VOUT The maximum RTON value allowed is shown by the following equation. Rton_MAX = R1 R2 Figure 3 - Output Voltage Selection As the control method regulates the valley of the output ripple voltage, the DC output voltage VOUT is off set by the output ripple according to the following equation. VOUT = 0.5 x (1 + R1/R2) + VRIPPLE/2 Gate drives One-shot timer To FB pin VOUT VIN_MIN 15 A Enable and Power-Save Inputs The EN/PSV and ENL inputs are used to enable or disable the switching regulator and the LDO. When EN/PSV is low (grounded), the switching regulator is off and in its lowest power state. When off, the output of the switching regulator soft-discharges the output into a 15 internal resistor via the VOUT pin. When EN/PSV is allowed to float, the pin voltage will fl oat to 1.5 V. The switching regulator turns on with power-save disabled and all switching is in forced continuous mode. When EN/PSV is high (above 2.0 V), the switching regulator turns on with ultra-sonic power-save enabled. The SiC417 ultra-sonic power-save operation maintains a minimum switching frequency of 25 kHz, for applications with stringent audio requirements. The ENL input is used to control the internal LDO. This input serves a second function by acting as a VIN UVLO sensor for the switching regulator. The LDO is off when ENL is low (grounded). When ENL is a logic high but below the VIN UVLO threshold (2.6 V typical), then the LDO is on and the switcher is off. When ENL is above the VIN UVLO threshold, the LDO is enabled and the switcher is also enabled if the EN/PSV pin is not grounded. Forced Continuous Mode Operation The SiC417 operates the switcher in Forced Continuous Mode (FCM) by floating the EN/PSV pin (see figure 4). In this mode one of the power MOSFETs is always on, with no intentional dead time other than to avoid cross-conduction. This feature results in uniform frequency across the full load range with the trade-off being poor efficiency at light loads due to the high-frequency switching of the MOSFETs. VOUT Voltage Selection The switcher output voltage is regulated by comparing VOUT as seen through a resistor divider at the FB pin to the internal 500 mV reference voltage, see figure 3. www.vishay.com 8 Document Number: 69062 S10-1367-Rev. D, 14-Jun-10 SiC417 Vishay Siliconix FB ripple voltage (VFB) FB threshold (500 mV) DC load current Inductor current On-time (tON) DH on-time is triggered when VFB reaches the FB threshold DH Because the on-times are forced to occur at intervals no greater than 40 s, the frequency will not fall below ~ 25 kHz. Figure 5 shows ultra-sonic power-save operation. Benefits of Ultrasonic Power-Save Having a fixed minimum frequency in power-save has some significant advantages as below: * The minimum frequency of 25 kHz is outside the audible range of human ear. This makes the operation of the SiC417 very quiet. * The output voltage ripple seen in power-save mode is significant lower than conventional power-save, which improves efficiency at light loads. * Lower ripple in power-save also makes the power component selection easier. DL DL drives high when on-time is completed. DL remains high until VFB falls to the FB threshold. Figure 4 - Forced Continuous Mode Operation Ultrasonic Power-Save Operation The SiC417 provides ultra-sonic power-save operation at light loads, with the minimum operating frequency fixed at 25 kHz. This is accomplished using an internal timer that monitors the time between consecutive high-side gate pulses. If the time exceeds 40 s, DL drives high to turn the low-side MOSFET on. This draws current from VOUT through the inductor, forcing both VOUT and VFB to fall. When VFB drops to the 500 mV threshold, the next DH on-time is triggered. After the on-time is completed the high-side MOSFET is turned off and the low-side MOSFET turns on, the low-side MOSFET remains on until the inductor current ramps down to zero, at which point the low-side MOSFET is turned off. Figure 6 - Ultrasonic Power-Save Operation Mode Figure 6 shows the behavior under power-save and continuous conduction mode at light loads. minimum fSW ~ 25 kHz FB ripple voltage (VFB) FB threshold (500 mV) (0A) Inductor current On-time (tON) DH on-time is triggered when VFB reaches the FB threshold DH DL Smart Power-Save Protection Active loads may leak current from a higher voltage into the switcher output. Under light load conditions with powersavepower-save enabled, this can force VOUT to slowly rise and reach the over-voltage threshold, resulting in a hard shutdown. Smart power-save prevents this condition. When the FB voltage exceeds 10 % above nominal (exceeds 550 mV), the device immediately disables power-save, and DL drives high to turn on the low-side MOSFET. This draws current from VOUT through the inductor and causes VOUT to fall. When VFB drops back to the 500 mV trip point, a normal tON switching cycle begins. This method prevents a hard OVP shutdown and also cycles energy from VOUT back to VIN. It also minimizes operating power by avoiding forced conduction mode operation. Figure 7 shows typical waveforms for the smart power-save feature. After the 40 s time-out, DL drives high if VFB has not reached the FB threshold. Figure 5 - Ultrasonic power-save Operation Document Number: 69062 S10-1367-Rev. D, 14-Jun-10 www.vishay.com 9 SiC417 Vishay Siliconix VOUT drifts up to due to leakage current flowing into COUT Smart power save threshold (550 mV) VOUT discharges via inductor and low-side MOSFET Normal VOUT ripple FB threshold DH and DL off High-side drive (DH) Single DH on-time pulse after DL turn-off Low-side drive (DL) DL turns on when smart PSAVE threshold is reached DL turns off FB threshold is reached Normal DL pulse after DH on-time pulse Figure 7 - Smart Power-Save Current Limit Protection The SiC417 features programmable current limit capability, which is accomplished by using the RDS(ON) of the lower MOSFET for current sensing. The current limit is set by RILIM resistor. The RILIM resistor connects from the ILIM pin to the LX pin which is also the drain of the low-side MOSFET. When the low-side MOSFET is on, an internal ~ 10 A current flows from the ILIM pin and the RILIM resistor, creating a voltage drop across the resistor. While the low-side MOSFET is on, the inductor current flows through it and creates a voltage across the RDS(ON). The voltage across the MOSFET is negative with respect to ground. If this MOSFET voltage drop exceeds the voltage across RILIM, the voltage at the ILIM pin will be negative and current limit will activate. The current limit then keeps the low-side MOSFET on and will not allow another high-side on-time, until the current in the low-side MOSFET reduces enough to bring the ILIM voltage back up to zero. This method regulates the inductor valley current at the level shown by ILIM in figure 8. Inductor Current IPEAK ILOAD ILIM Time Figure 8 - Valley Current Limit Setting the valley current limit to 10 A results in a 10 A peak inductor current plus peak ripple current. In this situation, the average (load) current through the inductor is 10 A plus one-half the peak-to-peak ripple current. The internal 10 A current source is temperature compensated at 4100 ppm in order to provide tracking with the RDS(ON). The RILIM value is calculated by the following equation. RILIM = 735 x ILIM www.vishay.com 10 Note that because the low-side MOSFET with low RDS(ON) is used for current sensing, the PCB layout, solder connections, and PCB connection to the LX node must be done carefully to obtain good results. Refer to the layout guidelines for information. Soft-Start of PWM Regulator Soft-start is achieved in the PWM regulator by using an internal voltage ramp as the reference for the FB Comparator. The voltage ramp is generated using an internal charge pump which drives the reference from zero to 500 mV in ~ 1.2 mV increments, using an internal ~ 500 kHz oscillator. When the ramp voltage reaches 500 mV, the ramp is ignored and the FB comparator switches over to a fixed 500 mV threshold. During soft-start the output voltage tracks the internal ramp, which limits the start-up inrush current and provides a controlled softstart profile for a wide range of applications. Typical softstart ramp time is 850 s. During soft-start the regulator turns off the low-side MOSFET on any cycle if the inductor current falls to zero. This prevents negative inductor current, allowing the device to start into a pre-biased output. Power Good Output The power good (PGOOD) output is an open-drain output which requires a pull-up resistor. When the output voltage is 10 % below the nominal voltage, PGOOD is pulled low. It is held low until the output voltage returns above - 8 % of nominal. PGOOD is held low during start-up and will not be allowed to transition high until soft-start is completed (when VFB reaches 500 mV) and typically 2 ms has passed. PGOOD will transition low if the VFB pin exceeds + 20 % of nominal, which is also the over-voltage shutdown threshold (600 mV). PGOOD also pulls low if the EN/PSV pin is low when V5V is present. Output Over-Voltage Protection Over-voltage protection becomes active as soon as the device is enabled. The threshold is set at 500 mV + 20 % (600 mV). When VFB exceeds the OVP threshold, DL latches high and the low-side MOSFET is turned on. DL remains high and the controller remains off , until the EN/PSV input is toggled or V5V is cycled. There is a 5 s delay built into the OVP detector to prevent false transitions. PGOOD is also low after an OVP event. Output Under-Voltage Protection When VFB falls 25 % below its nominal voltage (falls to 375 mV) for eight consecutive clock cycles, the switcher is shut off and the DH and DL drives are pulled low to tristate the MOSFETs. The controller stays off until EN/PSV is toggled or V5V is cycled. V5V UVLO, and POR Under-voltage lock-out (UVLO) circuitry inhibits switching and tri-states the DH/DL drivers until V5V rises above 3.9 V. An internal Power-On Reset (POR) occurs when V5V exceeds 3.9 V, which resets the fault latch and soft-start Document Number: 69062 S10-1367-Rev. D, 14-Jun-10 SiC417 Vishay Siliconix counter to prepare for soft-start. The SiC417 then begins a soft-start cycle. The PWM will shut off if V5V falls below 3.6 V. LDO Regulator The SiC417 features an integrated LDO regulator with a programmable output voltage from 0.75 V to 5.25 V using external resistors, when an external supply is used to power V5V. The feedback pin (FBL) for the LDO is regulated to 750 mV. There is also an enable pin (ENL) for the LDO that provides independent control. The LDO voltage can also be used to provide the bias voltage for the switching regulator, when VLDO is tied to V5V. More detail can be found in the On Chip LDO bias section coming up. To FBL pin VLDO RLDO1 RLDO2 Figure 9 - LDO Start-Up The LDO output voltage is set by the following equation. VLDO = 750 mV x 1+ ( RLDO1 RLDO2 ) A minimum capacitance of 1 F referenced to AGND is normally required at the output of the LDO for stability. If the LDO is providing bias power to the device, then a minimum 0.1 F capacitor referenced to AGND is required along with a minimum 1.0 F capacitor referenced to PGND to filter the gate drive pulses. Refer to the layout guideline section. LDO Start-up Before start-up, the LDO checks the status of the following signals to ensure proper operation can be maintained. 1. ENL pin 2. VLDO output 3. VIN input voltage When the ENL pin is high and VIN is above the UVLO point, the LDO will begin start-up. During the initial phase, when the LDO output voltage is near zero, the LDO initiates a current-limited start-up (typically 85 mA) to charge the output capacitor. When VLDO has reached 90 % of the final value (as sensed at the FBL pin), the LDO current limit is increased to ~ 200 mA and the LDO output is quickly driven to the nominal value by the internal LDO regulator. VVLDO final Voltage regulating with ~ 200 mA current limit 90 % of VVLDO final Constant current startup LDO Switchover Function The SiC417 includes a switch-over function for the LDO. The switch-over function is designed to increase efficiency by using the more efficient dc-to-dc converter to power the LDO output, avoiding the less efficient LDO regulator when possible. The switch-over function connects the VLDO pin directly to the VOUT pin using an internal switch. When the switch-over is complete the LDO is turned off, which results in a power savings and maximizes efficiency. If the LDO output is used to bias the SiC417, then after switch-over the device is self-powered from the switching regulator with the LDO turned off. The switch-over logic waits for 32 switching cycles before it starts the switch-over. There are two methods that determine the switch-over of VLDO to VOUT. In the first method, the LDO is already in regulation and the dc-to-dc converter is later enabled. As soon as the PGOOD output goes high, the 32 cycles are started. The voltages at the VLDO and VOUT pins are then compared; if the two voltages are within 300 mV of each other, the VLDO pin connects to the VOUT pin using an internal switch, and the LDO is turned off. In the second method, the dc-to-dc converter is already running and the LDO is enabled. In this case the 32 cycles are started as soon as the LDO reaches 90 % of its final value. At this time, the VLDO and VOUT pins are compared, and if within 300 mV the switch-over occurs and the LDO is turned off. Benefits of having a switchover circuit The switchover function is designed to get maximum efficiency out of the dc-to-dc converter. The efficiency for an LDO is very low especially for high input voltages. Using the switchover function we tie any rails connected to VLDO through a switch directly to VOUT. Once switchover is complete LDO is turned off which saves power. This gives us the maximum efficiency out of the SiC417. If the LDO output is used to bias the SiC417, then after switchover the VOUT self biases the SiC417 and operates in self-powered mode. Steps to follow when using the on chip LDO to bias the SiC417: * Always tie the V5V to VLDO before enabling the LDO * Enable the LDO before enabling the switcher * LDO has a current limit of 85 mA at start-up with 12 VIN, so do not connect any load between VLDO and ground * The current limit for the LDO goes up to 200 mA once the VLDO reaches 90 % of its final values and can easily supply the required bias current to the IC. Switch-over Limitations on VOUT and VLDO Because the internal switch-over circuit always compares the VOUT and VLDO pins at start-up, there are limitations on permissible combinations of VOUT and VLDO. Consider the case where VOUT is programmed to 1.5 V and VLDO is programmed to 1.8 V. After start-up, the device would connect VOUT to VLDO and disable the LDO, since the two voltages are within the 300 mV switch-over window. Figure 10 - LDO Start-Up Document Number: 69062 S10-1367-Rev. D, 14-Jun-10 www.vishay.com 11 SiC417 Vishay Siliconix To avoid unwanted switch-over, the minimum difference between the voltages for VOUT and VLDO should be 500 mV. It is not recommended to use the switch-over feature for an output voltage less than 3 V since this does not provide sufficient voltage for the gate-source drive to the internal p-channel switch-over MOSFET. Switch-Over MOSFET Parasitic Diodes The switch-over MOSFET contains parasitic diodes that are inherent to its construction, as shown in figure 11. Switchover control Switchover MOSFET VOUT VLDO Parastic diode Parastic diode V5V Figure 11 - Switch-over MOSFET Parasitic Diodes There are some important design rules that must be followed to prevent forward bias of these diodes. The following two conditions need to be satisfied in order for the parasitic diodes to stay off. * V5V VLDO * V5V VOUT If either VLDO or VOUT is higher than V5V, then the respective diode will turn on and the SiC417 operating current will flow through this diode. This has the potential of damaging the device. ENL Pin and VIN UVLO The ENL pin also acts as the switcher under-voltage lockout for the VIN supply. The VIN UVLO voltage is programmable via a resistor divider at the VIN, ENL and AGND pins. ENL is the enable/disable signal for the LDO. In order to implement the VIN UVLO there is also a timing requirement that needs to be satisfied. If the ENL pin transitions low within 2 switching cycles and is < 1 V, then the LDO will turn off but the switcher remains on. If ENL goes below the VIN UVLO threshold and stays above 1 V, then the switcher will turn off but the LDO remains on. The VIN UVLO function has a typical threshold of 2.6 V on the VIN rising edge. The falling edge threshold is 2.4 V. Note that it is possible to operate the switcher with the LDO disabled, but the ENL pin must be below the logic low threshold (0.4 V maximum). However, if the switcher was previously operating (with EN/ PSV high but ENL at ground, and V5V supplied externally), then it is undesirable to shut down the switcher. To prevent this, when the ENL input is taken above 2.6 V (above the VIN UVLO threshold), the internal logic checks the PGOOD signal. If PGOOD is high, then the switcher is already running and the LDO will run through the start-up cycle without affecting the switcher. If PGOOD is low, then the LDO will not allow any PWM switching until the LDO output has reached 90 % of it's final value. On-Chip LDO Bias the SiC417 The following steps must be followed when using the onchip LDO to bias the device. * Connect V5V to VLDO before enabling the LDO. * The LDO has an initial current limit of 85 mA at start-up with 12 VIN, therefore, do not connect any external load to VLDO during start-up. * When VLDO reaches 90 % of its final value, the LDO current limit increases to 200 mA. At this time the LDO may be used to supply the required bias current to the device. * Switching will be held off until VLDO reaches regulation. Attempting to operate in self-powered mode in any other configuration can cause unpredictable results and may damage the device. Design Procedure When designing a switch mode power supply, the input voltage range, load current, switching frequency, and inductor ripple current must be specified. The maximum input voltage (VINMAX) is the highest specified input voltage. The minimum input voltage (VINMIN) is determined by the lowest input voltage after evaluating the voltage drops due to connectors, fuses, switches, and PCB traces. The following parameters define the design: * Nominal output voltage (VOUT) * Static or DC output tolerance * Transient response * Maximum load current (IOUT) There are two values of load current to evaluate - continuous load current and peak load current. Continuous load current relates to thermal stresses which drive the selection of the inductor and input capacitors. Peak load current determines instantaneous component stresses and filtering requirements such as inductor saturation, output capacitors, and design of the current limit circuit. The following values are used in this design: * VIN = 12 V 10 % * VOUT = 1.05 V 4 % * fSW = 250 kHz * Load = 10 A maximum ENL Logic Control of PWM Operation When the ENL input is driven above 2.6 V, it is impossible to determine if the LDO output is going to be used to power the device or not. In self-powered operation where the LDO will power the device, it is necessary during the LDO start-up to hold the PWM switching off until the LDO has reached 90 % of the final value. This is to prevent overloading the current-limited LDO output during the LDO start-up. www.vishay.com 12 Document Number: 69062 S10-1367-Rev. D, 14-Jun-10 SiC417 Vishay Siliconix Frequency Selection Selection of the switching frequency requires making a trade-off between the size and cost of the external filter components (inductor and output capacitor) and the power conversion efficiency. The desired switching frequency is 250 kHz which results from using component selected for optimum size and cost. A resistor (RTON) is used to program the on-time (indirectly setting the frequency) using the following equation. (t - 10 ns) x VIN Rton = ON 25 pF x VOUT To select RTON, use the maximum value for VIN, and for tON use the value associated with maximum VIN. tON = VOUT VINMAX. x fSW tON = 318 ns at 13.2 VIN, 1.05 VOUT, 250 kHz Substituting for RTON results in the following solution RTON = 154.9 k, use RTON = 154 k. Inductor Selection In order to determine the inductance, the ripple current must first be defined. Low inductor values result in smaller size but create higher ripple current which can reduce efficiency. Higher inductor values will reduce the ripple current and voltage and for a given DC resistance are more efficient. However, larger inductance translates directly into larger packages and higher cost. Cost, size, output ripple, and efficiency are all used in the selection process. The ripple current will also set the boundary for power-save operation. The switching will typically enter power-save mode when the load current decreases to 1/2 of the ripple current. For example, if ripple current is 4 A then power-save operation will typically start for loads less than 2 A. If ripple current is set at 40 % of maximum load current, then powersave will start for loads less than 20 % of maximum current. The inductor value is typically selected to provide a ripple current that is between 25 % to 50 % of the maximum load current. This provides an optimal trade-off between cost, efficiency, and transient performance. During the DH on-time, voltage across the inductor is (VIN-VOUT). The equation for determining inductance is shown next. Note that the inductor must be rated for the maximum DC load current plus 1/2 of the ripple current. The ripple current under minimum VIN conditions is also checked using the following equations. TON_VINMIN = IRIPPLE = 25 pF x RTON x VOUT VINMIN (VIN - VOUT) x TON L IRIPPLE_VIN = (10.8 - 1.05) x 384 ns = 4.25 A 0.88 H Capacitor Selection The output capacitors are chosen based on required ESR and capacitance. The maximum ESR requirement is controlled by the output ripple requirement and the DC tolerance. The output voltage has a DC value that is equal to the valley of the output ripple plus 1/2 of the peak-to-peak ripple. Change in the output ripple voltage will lead to a change in DC voltage at the output. The design goal is that the output voltage regulation be 4 % under static conditions. The internal 500 mV reference tolerance is 1 %. Allowing 1 % tolerance from the FB resistor divider, this allows 2 % tolerance due to VOUT ripple. Since this 2 % error comes from 1/2 of the ripple voltage, the allowable ripple is 4 %, or 42 mV for a 1.05 V output. The maximum ripple current of 4.4 A creates a ripple voltage across the ESR. The maximum ESR value allowed is shown by the following equations. ESRMAX = VRIPPLE IRIPPLEMAX L= (13.2 - 1.05) x 318 ns = 77 H 5A A slightly larger value of 0.88 H is selected. This will decrease the maximum IRIPPLE to 4.4 A. Document Number: 69062 S10-1367-Rev. D, 14-Jun-10 4.4 A The output capacitance is usually chosen to meet transient requirements. A worst-case load release, from maximum load to no load at the exact moment when inductor current is at the peak, determines the required capacitance. If the load release is instantaneous (load changes from maximum to zero in < 1 s), the output capacitor must absorb all the inductor's stored energy. This will cause a peak voltage on the capacitor according to the following equation. 1 xI )2 2 RIPPLEMAX (VPEAK)2 - (VOUT)2 L (IOUT + (VIN - VOUT) x tON IRIPPLE Example In this example, the inductor ripple current is set equal to 50 % of the maximum load current. Thus ripple current will be 50 % x 10 A or 5 A. To find the minimum inductance needed, use the VIN and TON values that correspond to VINMAX. 42 mV ESRMAX = 9.5 m COUTMIN = L= = Assuming a peak voltage VPEAK of 1.150 (100 mV rise upon load release), and a 10 A load release, the required capacitance is shown by the next equation. 1 x 4.4)2 2 2 (1.15) - (1.05)2 0.88 H (10 + COUTMIN = COUTMIN = 595 F If the load release is relatively slow, the output capacitance can be reduced. At heavy loads during normal switching, when the FB pin is above the 500 mV reference, the DL www.vishay.com 13 SiC417 Vishay Siliconix output is high and the low-side MOSFET is on. During this time, the voltage across the inductor is approximately - VOUT. This causes a down-slope or falling di/dt in the inductor. If the load dI/dt is not much faster than the - dI/dt in the inductor, then the inductor current will tend to track the falling load current. This will reduce the excess inductive energy that must be absorbed by the output capacitor, therefore a smaller capacitance can be used. The following can be used to calculate the needed capacitance for a given dILOAD/dt: Peak inductor current is shown by the next equation. ILPK = IMAX + 1/2 x IRIPPLEMAX ILPK = 10 + 1/2 x 4.4 = 12.2 A Rate of change of load current = dILOAD/dt IMAX = maximum load release = 10 A I I L x LPK - MAX x dt VOUT dlLOAD COUT = ILPK x 2 (VPK - VOUT) Example Load dlLOAD 2.5 A = s dt This would cause the output current to move from 10 A to zero in 4 s as shown by the following equation. 12.2 10 x 1 s 1.05 2.5 2 (1.15 - 1.05) 0.88 H x COUT = 12.2 x COUT = 379 F Note that COUT is much smaller in this example, 379 F compared to 595 F based on a worst-case load release. To meet the two design criteria of minimum 379 F and maximum 9 m ESR, select two capacitors rated at 220 F and 15 m ESR. It is recommended that an additional small capacitor be placed in parallel with COUT in order to filter high frequency switching noise. Stability Considerations Unstable operation is possible with adaptive on-time controllers, and usually takes the form of double-pulsing or ESR loop instability. Double-pulsing occurs due to switching noise seen at the FB input or because the FB ripple voltage is too low. This causes the FB comparator to trigger prematurely after the 250 ns minimum off-time has expired. In extreme cases the noise can cause three or more successive on-times. Double-pulsing will result in higher ripple voltage at the output, but in most applications it will not affect operation. This form of instability can usually be avoided by providing the FB pin with a smooth, clean ripple signal that is at least 10 mVp-p, which may dictate the need to increase the ESR of the output capacitors. It is also imperative to provide a proper PCB layout as discussed in the Layout Guidelines section. www.vishay.com 14 CTOP VOUT To FB pin R1 R2 Figure 13 - Capacitor Coupling to FB Pin Another way to eliminate doubling-pulsing is to add a small (~ 10 pF) capacitor across the upper feedback resistor, as shown in figure 13. This capacitor should be left unpopulated until it can be confirmed that double-pulsing exists. Adding the CTOP capacitor will couple more ripple into FB to help eliminate the problem. An optional connection on the PCB should be available for this capacitor. ESR loop instability is caused by insufficient ESR. The details of this stability issue are discussed in the ESR Requirements section. The best method for checking stability is to apply a zero-to-full load transient and observe the output voltage ripple envelope for overshoot and ringing. Ringing for more than one cycle after the initial step is an indication that the ESR should be increased. One simple way to solve this problem is to add trace resistance in the high current output path. A side effect of adding trace resistance is output decreased load regulation. ESR Requirements A minimum ESR is required for two reasons. One reason is to generate enough output ripple voltage to provide10 mVp-p at the FB pin (after the resistor divider) to avoid doublepulsing. The second reason is to prevent instability due to insufficient ESR. The on-time control regulates the valley of the output ripple voltage. This ripple voltage is the sum of the two voltages. One is the ripple generated by the ESR, the other is the ripple due to capacitive charging and discharging during the switching cycle. For most applications the minimum ESR ripple voltage is dominated by the output capacitors, typically SP or POSCAP devices. For stability the ESR zero of the output capacitor should be lower than approximately one-third the switching frequency. The formula for minimum ESR is shown by the following equation. ESRMIN = 3 2 x x COUT x fSW For applications using ceramic output capacitors, the ESR is normally too small to meet the above ESR criteria. In these applications it is necessary to add a small virtual ESR network composed of two capacitors and one resistor, as shown in figure 14. This network creates a ramp voltage Document Number: 69062 S10-1367-Rev. D, 14-Jun-10 SiC417 Vishay Siliconix across CL, analogous to the ramp voltage generated across the ESR of a standard capacitor. This ramp is then capacitive-coupled into the FB pin via capacitor CC. L Highside CL RL R1 Lowside CC COUT R2 FB pin Figure 14 - Virtual ESR Ramp Current Dropout Performance The output voltage adjusts range for continuous-conduction operation is limited by the fixed 250 ns (typical) minimum off-time of the one-shot. When working with low input voltages, the duty-factor limit must be calculated using worst-case values for on and off times. The duty-factor limitation is shown by the next equation. DUTY = TON(MIN) TON(MIN) x TOFF(MAX) The inductor resistance and MOSFET on-state voltage drops must be included when performing worst-case dropout duty-factor calculations. This trace resistance should be optimized so that at full load the output droops to near the lower regulation limit. Passive droop minimizes the required output capacitance because the voltage excursions due to load steps are reduced as seen at the load. The use of 1 % feedback resistors contributes up to 1 % error. If tighter DC accuracy is required, 0.1 % resistors should be used. The output inductor value may change with current. This will change the output ripple and therefore will have a minor effect on the DC output voltage. The output ESR also affects the output ripple and thus has a minor effect on the DC output voltage. Switching Frequency Variations The switching frequency will vary depending on line and load conditions. The line variations are a result of fixed propagation delays in the on-time one-shot, as well as unavoidable delays in the external MOSFET switching. As VIN increases, these factors make the actual DH on-time slightly longer than the ideal on-time. The net effect is that frequency tends to falls slightly with increasing input voltage. The switching frequency also varies with load current as a result of the power losses in the MOSFETs and the inductor. For a conventional PWM constant-frequency converter, as load increases the duty cycle also increases slightly to compensate for IR and switching losses in the MOSFETs and inductor. A constant on-time converter must also compensate for the same losses by increasing the effective duty cycle (more time is spent drawing energy from VIN as losses increase). The on-time is essentially constant for a given VOUT/VIN combination, to off set the losses the off-time will tend to reduce slightly as load increases. The net effect is that switching frequency increases slightly with increasing load. System DC Accuracy (VOUT Controller) Three factors affect VOUT accuracy: the trip point of the FB error comparator, the ripple voltage variation with line and load, and the external resistor tolerance. The error comparator off set is trimmed so that under static conditions it trips when the feedback pin is 500 mV, 1 %. The on-time pulse from the SiC417 in the design example is calculated to give a pseudo-fixed frequency of 250 kHz. Some frequency variation with line and load is expected. This variation changes the output ripple voltage. Because constant on-time converters regulate to the valley of the output ripple, 1/2 of the output ripple appears as a DC regulation error. For example, if the output ripple is 50 mV with VIN = 6 V, then the measured DC output will be 25 mV above the comparator trip point. If the ripple increases to 80 mV with VIN = 25 V, then the measured DC output will be 40 mV above the comparator trip. The best way to minimize this effect is to minimize the output ripple. To compensate for valley regulation, it may be desirable to use passive droop. Take the feedback directly from the output side of the inductor and place a small amount of trace resistance between the inductor and output capacitor. Document Number: 69062 S10-1367-Rev. D, 14-Jun-10 www.vishay.com 15 V5V P3 V5V B2 V IN_GND B1 V IN 1 1 1 1 C26 4.7 F 1 M1 1 J7 Probe Test Pin 5 C12 150 F + P1 VIN C27 4.7 F * C8 10 F 5 2 4 3 1 1 M2 1 P4 VLDO 1 M3 1 1 R29 10K 1 M4 2 7 3 6 9 10 11 34 R6 100K ENL P6 C13 0.01 F R12 57.6K C11 0.1 F R2 300K * C29 22 F 0 C10 10 F C28 R11 0.1 F C9 10 F V IN J4 Probe Test Pin EN_PSV 1 5 1 FBL VLDO V5V VIN VIN VIN VIN VIN 32 ENL R1 300K * 29 EN/PSV P5 14 U1 SiC417 DL 5 R39 0R 27 1 28 25 24 23 13 33 C32 1n 26 PGD 31 TON ILIM FB LX LX LX LX LX LX R7 0 R30 75K C30 47 pF R40 1 R15 10K R8 10K C6 0.1 F J3 Probe Test Pin C5 0.1 F 5 J2 Probe Test Pin 3 4 2 BST P2 V IN_GND 1 1 3 4 2 12 DH 3 4 2 1 8 PGND PGND PGND PGND PGND PGND PGND PGND AGND AGND AGND 17 18 19 20 21 22 16 15 35 4 30 3 4 2 1 V5V 1 5 VOUT 1 L1 C24 10n * P7 C14 0.1 F 1 C19 1 * 1 H J5 Probe Test Pin R13 1K R9 * 5 R3 1K P8 1 V5V P GOOD C15 10 F 1R01 1 Q1 Si4812BDY C7 0.1 F R5 100K + + + + C1 22 F C31 100 pF * C25 68 pF C20 C21 C22 C18 C16 C23 C17 10 F 10 F 10 F 220 F 220 F 220 F 220 F P12 LDTRG R4 Step_I_Sense C2 22 F R23 7.15K R10 10K 5 C3 22 F 1 P11 VO_GND VCTRL P9 P10 VO 1 J6 Probe Test Pin Vo C4 22 F 2 4 3 1 www.vishay.com 16 1 J1 3 Probe Test Pin 4 1 2 B4 VO V O_GND 1 1 B3 SiC417 Vishay Siliconix SiC417 EVALUATION BOARD SCHEMATIC Figure 15. Evaluation Board Schematic Document Number: 69062 S10-1367-Rev. D, 14-Jun-10 SiC417 Vishay Siliconix BILL OF MATERIALS Reference Designator Value Voltage B1, B2, B3, B4 Footprint Part Number Manufacturer SOLDER-BANANA 575-4 Keystone C29 22 F 16 V SM/C_1210 GRM32ER71C226ME18L Murata C5 0.1 F 10 V SM/C_0402 C0402C104K8RAC7867 Vishay C6 0.1 F 10 V SM/C_0805 C0402C104K8RAC7867 Vishay C11, C14, C28 0.1 F 50 V SM/C_0603 VJ0603Y104KXACW1BC Vishay C8, C9, C10 10 F 25 V SM/C_1210 TMK325B7106MN-T Taiyo Yuden C12 150 F 35 V D8X11.5-D0.6X3.5 EEU-FM1V151 Panasonic C13 0.01 F 50 V SM/C_0402 VJ0402Y103KXACW1BC Vishay C15, C20, C21, C22 10 F 16 V SM/C_1206 GRM31CR71C106KAC7L C16, C17, C18, C23 220 F 10 V 595D-D 593D227X0010E2TE3 C19 1 F Vishay SM/C_0603 C24 10 nF C25 100 pF 50 V SM/C_0402 VJ0402A101JXACW1BC Vishay C26 4.7 F 10 V SM/C_0805 LMK212B7475KG-T Taiyo Yuden C27 4.7 F 10 V SM/C_0805 LMK212B7475KG-T Taiyo Yuden C30 47 pF SM/C_0402 VJ0402A470JXACW1BC SM/C_0402 VJ0402Y101KXQCW1BC Vishay SM/C_0805 VJ0805A102KXA Vishay Lecroy Probe Pin PK007-015 Lecroy C31 100 pF C32 1000 pF J1, J2, J3, J4, J5, J6, J7 Probe test pin SM/C_0603 50 V L1 1 H IHLP4040 IHLP4040DZER1R0M01 Vishay M1, M2, M3, M4 M HOLE2 Stacking Spacer 8834 Keystone P1, P2, P3, P4, P5, P6, P7, P8, P9, P10, P11, P12 VIN, GND etc. Probe Hook 1540-2 Keystone R1 300K 50 V SM/C_0603 CRCW060310K0FKEA Vishay R2 300K 50 V SM/C_0603 CRCW06030000FKEA Vishay SM/C_0402 CRCW04021K00FKED Vishay 50 V SM/C_0603 CRCW0603100KFKEA Vishay R3, R13 1K R6 100K R7, R11 0R SM/C_0603 CRCW06030000Z0EA Vishay R8, R10, R15, R29 10K SM/C_0603 MCR03EZHF1002 ROHM R9 SM/C_0603 R12 57.6K SM/C_0603 CRCW060357K6FKEA Vishay R23 7.15K SM/C_0603 CRCW06037K15FKEA Vishay R30 75K SM/C_0603 CRCW0603154KFKEA Vishay R39 0R SM/C_0402 CRCW04020000Z0ED Vishay CRCW08051R00FNEA R40 1 SM/C_0805 U1 SiC417 QFN5X5_32 leads + 3 pads Vishay Vishay Optional Cicuitry for Transient Response Testing Q1 Si4812BDY 30 V SO-8 Si4812BDY Vishay R4 1R01 200 V C_2512 CRCW25121R00FKTA Vishay R5 100K 50 V SM/C_0603 CRCW0603100KFKEA Vishay C7 0.1 F 50 V SM/C_0603 VJ0603Y104KXACW1BC Vishay C1, C2, C3, C4 22 F 16 V SM/C_1210 GRM32ER71C226ME18L Murata Document Number: 69062 S10-1367-Rev. D, 14-Jun-10 www.vishay.com 17 SiC417 Vishay Siliconix PCB LAYOUT OF THE EVALUATION BOARD www.vishay.com 18 Figure 16. PCB Layout - Top Layer Figure 17. PCB Layout - MidLayer1 Figure 18. PCB Layout - MidLayer2 Figure 19. PCB Layout - Bottom Layer Document Number: 69062 S10-1367-Rev. D, 14-Jun-10 SiC417 Vishay Siliconix PACKAGE DIMENSIONS AND MARKING INFO 5.000 0.075 A + 5.000 0.075 Pin # 1 (Laser Marked) Top View B 0.10 C 0.08 C C 0.900 0.100 0.050 0.000 0.460 Bare Copper 16 CL 9 17 8 3.480 0.100 CL 0.460 Bottom View R Full 0.250 0.050 0.10 C AB 1.485 0.100 0.200 ref. 1.970 0.100 24 25 32 R0.200 Pin 1 I.D. 1.660 0.100 0.500 0.400 0.100 1.050 0.100 Vishay Siliconix maintains worldwide manufacturing capability. Products may be manufactured at one of several qualified locations. Reliability data for Silicon Technology and Package Reliability represent a composite of all qualified locations. For related documents such as package/tape drawings, part marking, and reliability data, see www.vishay.com/ppg?69062. Document Number: 69062 S10-1367-Rev. D, 14-Jun-10 www.vishay.com 19 Package Information Vishay Siliconix PowerPAK(R) MLP55-32L CASE OUTLINE 0.08 C A A1 D A2 25 1 4 (5 mm x 5 mm) Pin #1 identification R0.200 E2 - 3 0.10 E 32L T/SLP D2 - 2 32 24 E2 - 1 CAB e 0.10 CB D2 - 1 0.360 8 17 B b 16 L C 0.36 Top View (Nd-1) Xe Ref. 0.10 CA A E2 - 2 2x 0.45 5 6 Pin 1 dot by marking 2x Side View D2 - 3 D2 - 4 (Nd-1) Xe Ref. D4 9 Bottom View MILLIMETERS INCHES DIM MIN. NOM. MAX. MIN. NOM. A 0.80 0.85 0.90 0.031 0.033 0.035 A1(8) 0.00 - 0.05 0.000 - 0.002 0.30 0.078 A2 b(4) 0.20 REF. 0.20 0.25 0.008 REF. 0.098 D 5.00 BSC 0.196 BSC e 0.50 BSC 0.019 BSC E 5.00 BSC L 0.35 0.40 MAX. 0.011 0.196 BSC 0.45 0.013 0.015 N(3) 32 32 Nd(3) 8 8 Ne(3) 8 0.017 8 D2 - 1 3.43 3.48 3.53 0.135 0.137 0.139 D2 - 2 1.00 1.05 1.10 0.039 0.041 0.043 D2 - 3 1.00 1.05 1.10 0.039 0.041 0.043 D2 - 4 1.92 1.97 2.02 0.075 0.077 0.079 E2 - 1 3.43 3.48 3.53 0.135 0.137 0.139 E2 - 2 1.61 1.66 1.71 0.063 0.065 0.067 E2 - 3 1.43 1.48 1.53 0.056 0.058 0.060 ECN: T-08957-Rev. A, 29-Dec-08 DWG: 5983 Notes 1. Use millimeters as the primary measurement. 2. Dimensioning and tolerances conform to ASME Y14.5M. - 1994. 3. N is the number of terminals. Nd is the number of terminals in X-direction and Ne is the number of terminals in Y-direction. 4. Dimension b applies to plated terminal and is measured between 0.20 mm and 0.25 mm from terminal tip. 5. The pin #1 identifier must be existed on the top surface of the package by using indentation mark or other feature of package body. 6. Exact shape and size of this feature is optional. 7. Package warpage max. 0.08 mm. 8. Applied only for terminals. Document Number: 64714 Revision: 29-Dec-08 www.vishay.com 1 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Revision: 12-Mar-12 1 Document Number: 91000