VEMI85AA-HGK www.vishay.com Vishay Semiconductors 8-Channel EMI-Filter with ESD-Protection FEATURES * Ultra compact LLP3313-17L package * Low package profile of 0.6 mm * 8-channel EMI-filter * Low leakage current * Line resistance RS = 100 * Typical cut off frequency f3dB = 100 MHz * ESD-protection acc. IEC 61000-4-2 30 kV contact discharge 30 kV air discharge 21840 16 15 14 13 11 12 10 * e4 - precious metal (e.g. Ag, Au, NiPd, NiPdAu) (no Sn) 9 * Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 17 20388 1 3 2 4 7 6 5 8 MARKING (example only) YYXX 20720 Dot = pin 1 marking Y = type code (see table below) XX = date code ORDERING INFORMATION DEVICE NAME ORDERING CODE TAPED UNITS PER REEL (8 mm TAPE ON 7" REEL) MINIMUM ORDER QUANTITY VEMI85AA-HGK VEMI85AA-HGK-GS08 3000 15 000 PACKAGE DATA DEVICE NAME PACKAGE NAME TYPE CODE WEIGHT MOLDING COMPOUND FLAMMABILITY RATING MOISTURE SENSITIVITY LEVEL SOLDERING CONDITIONS VEMI85AA-HGK LLP3313-17L 9R 7.4 mg UL 94 V-0 MSL level 1 (according J-STD-020) 260 C/10 s at terminals ABSOLUTE MAXIMUM RATINGS PARAMETER Peak pulse current ESD immunity Operating temperature Storage temperature Rev. 1.7, 03-Aug-12 TEST CONDITIONS SYMBOL VALUE UNIT All I/O pin to pin 17; acc. IEC 61000-4-5; tp = 8/20 s; single shot IPPM 4 A Contact discharge acc. IEC 61000-4-2; 10 pulses Air discharge acc. IEC 61000-4-2; 10 pulses Junction temperature VESD 30 30 kV TJ - 40 to + 125 C TSTG - 55 to + 150 C Document Number: 81386 1 For technical questions, contact: EMIFilter@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VEMI85AA-HGK www.vishay.com Vishay Semiconductors APPLICATION NOTE With the VEMI85AA-HGK 8 different signal or data lines can be filtered and clamped to ground. Due to the different clamping levels in forward and reverse direction the clamping behaviour is Bidirectional and Asymmetric (BiAs). L1OUT L1IN 1 16 L2IN 2 15 L2OUT 14 L3OUT L3IN L4IN L5IN L6IN 3 17 13 L4OUT 5 12 L5OUT 6 11 L6OUT 4 L7IN 7 10 L7OUT L8IN 8 9 L8OUT 20389 The 8 independent EMI-filter are placed between pin 1 and pin 16, pin 2 and pin 15, pin 3 and pin 14, pin 4 and pin 13, pin 5 and pin 12, pin 6 and pin 11, pin 7 and pin 10 and pin 8 and pin 9. They all are connected to a common ground pin 17 on the backside of the package. The circuit diagram of one EMI-filter-channel shows two identical Z-diodes at the input to ground and the output to ground. These Z-diodes are characterized by the breakthrough voltage level (VBR) and the diode capacitance (CD). Below the breakthrough voltage level the Z-diodes can be considered as capacitors. Together with these capacitors and the line resistance RS between input and output the device works as a low pass filter. Low frequency signals (f < f3dB) pass the filter while high frequency signals (f > f3dB) will be shorted to ground through the diode capacitances CD. RS In (pin 1, 2, 3, 4, 5, 6, 7, 8) Out (pin 9, 10, 11, 12, 13, 14, 15, 16) CD 20390 CD GND (pin 17) Each filter is symmetrical so that both ports can be used as input or output. Rev. 1.7, 03-Aug-12 Document Number: 81386 2 For technical questions, contact: EMIFilter@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VEMI85AA-HGK www.vishay.com Vishay Semiconductors ELECTRICAL CHARACTERISTICS All inputs (pin 1, 2, 3, 4, 5, 6, 7, and 8) to ground (pin 17) (Tamb = 25 C, unless otherwise specified) PARAMETER TEST CONDITIONS/REMARKS SYMBOL MIN. TYP. MAX. UNIT Number of channels which can be protected Nchannel - - 8 channel Max. reverse working voltage VRWM - - 5 V Reverse voltage at IR = 1 A VR 5 - - V Reverse current at VR = VRWM IR - - 1 A Reverse break down voltage at IR = 1 mA VBR 6 - - V at IPP = 1 A applied at the input, measured at the output; acc. IEC 61000-4-5 VC-out - - 7 V at IPP = IPPM = 4 A applied at the input, measured at the output; acc. IEC 61000-4-5 VC-out - - 8 V at IPP = - 1 A applied at the input, measured at the output; acc. IEC 61000-4-5 VC-out -1 - - V at IPP = IPPM = - 4 A applied at the input, measured at the output; acc. IEC 61000-4-5 VC-out - 1.2 - - V at VR = 0 V; f = 1 MHz CIN - 60 - pF at VR = 2.5 V; f = 1 MHz CIN - 36 - pF at 30 kV ESD-pulse acc. IEC 61000-4-2 VCESD - 7.5 - V Line resistance Measured between input and output; IS = 10 mA RS 90 100 110 Cut-off frequency VIN = 0 V; measured in a 50 system f3dB - 100 - MHz Protection paths Reverse stand off voltage Pos. clamping voltage Neg. clamping voltage Input capacitance ESD-clamping voltage TYPICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified) 120 % Rise time = 0.7 ns to 1 ns 8 s to 100 % 100 % 80 % 80 % 60 % IPPM Discharge Current IESD 100 % 60 % 53 % 40 % 27 % 20 % 20 % 0% - 10 0 10 20 30 40 50 60 70 80 90 100 Time (ns) 20557 Fig. 1 - ESD Discharge Current Wave Form acc. IEC 61000-4-2 (330 /150 pF) Rev. 1.7, 03-Aug-12 20 s to 50 % 40 % 0% 0 20548 10 20 30 40 Time (s) Fig. 2 - 8/20 s Peak Pulse Current Wave Form acc. IEC 61000-4-5 Document Number: 81386 3 For technical questions, contact: EMIFilter@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VEMI85AA-HGK www.vishay.com Vishay Semiconductors 70 100 f = 1 MHz 60 10 CIN (pF) 50 IF (mA) 1 0.1 40 30 20 0.01 0.001 10 0 0.5 0.6 0.7 0.8 0.9 Fig. 3 - Typical Forward Current IF vs. Forward Voltage VF 2 3 4 5 6 VIN (V) Fig. 6 - Typical Input Capacitance CIN vs. Input Voltage VIN 8 0 Transmission (S21) (dB) 7 6 5 VR (V) 1 20706 VF (V) 20705 0 1 4 3 2 1 0 0.01 -5 - 10 - 15 VINPUT = 5 V - 20 VINPUT = 2 V - 25 VINPUT = 1 V - 30 VINPUT = 0 V - 35 Measured in a 50 system - 40 0.1 1 20707 10 100 1000 10 000 IR (A) 1 20708 Fig. 4 - Typical Reverse Voltage VR vs. Reverse Current IR 10 100 1000 10 000 Frequency (MHz) Fig. 7 - Typical Small Signal Transmission (S21) at ZO = 50 14 12 Input clamping voltage VC (V) 10 8 Output clamping voltage 6 4 Measured acc. IEC 61000-4-5 (8/20 s - wave form) 2 0 0 20709 1 2 3 VC 4 5 6 7 IPP (A) Fig. 5 - Typical Peak Clamping Voltage VC vs. Peak Pulse Current IPP Rev. 1.7, 03-Aug-12 Document Number: 81386 4 For technical questions, contact: EMIFilter@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VEMI85AA-HGK www.vishay.com Vishay Semiconductors PACKAGE DIMENSIONS in millimeters (inches): LLP3313-17L 2.65 (0.104) 2.55 (0.100) exp. DAP 0.23 (0.009) 0.4 (0.016) bsc 0.3 (0.012) 0.24 (0.009) exp. DAP 0.45 (0.018) 0.35 (0.014) 0.2 (0.008) x 45 0.17 (0.007) 2.8 (0.110) ref. 1.4 (0.055) 0.5 (0.020) 3.35 (0.132) 3.25 (0.128) 0.6 (0.024) 0.152 (0.006) ref. 0 (0.000) 0.05 (0.002) 1.3 (0.051) Pin 1 marking Foot print recommendation: 7 x 0.4 = 2.8 (0.110) 0.4 (0.016) Document no.:S8-V-3906.04-003 (4) Created - Date: 28. August 2006 Rev. 1 - Date: 27. May 2008 0.4 (0.016) 0.4 (0.016) 2.6 (0.102) Solder resist mask 0.42 (0.017) 0.15 (0.006) 0.2 (0.008) Solder pad 20391 Rev. 1.7, 03-Aug-12 Document Number: 81386 5 For technical questions, contact: EMIFilter@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000