CE-10 XX Non-insulation type DC-DC converter 1 Y E A R S warranty ks Features F A F A SMD type ph Short in height (CE-1003/1004/1005: 4.5mm, CE-1050: 5.5mm) Wide temperature conditions: -40 - +85 (CE-1050: -20 - 85) range F A of operating F A Equipped with Remote On/Off function Equipped with Variable output voltage function 5-side metal-shielded low noise design pf-a Delivery in tray or by taping available F A F A CE-1005A is high efficiency than CE-1005 Model-naming method CE-1003-TP hk-a Packing type TP: Taping None: Tray Model number hws Series name Applications FA F A Conformity to RoHS Directive This means that, in conformity with EU Directive 2002/95/EC, lead, cadmium, mercury, hexavalent chro mium, and specific bromine-based flame retardants, PBB and PBDE, have not been used, except for exempted ap alpha dlp Model name CE-1003 F A CE-1004 F A CE-1005A CE-1050 3.00-5.25 3.00-5.25 9.0-26.4 6-16 Output voltage (V) 1.5-3.3 3.3-5.0 1.0-3.3 0.9-3.3 3.3-12.6 Output current (mA) 1500 1500 2500 2500 2500 F A 8-16 CE-1005 Input voltage (V) fps plications. Product Line up F A F A F A All specifications are subject to change without notice. 001-01/20080529 /etl_ce_10xx CE-1003, -1004 CE-1003, -1004 Specifications MODEL ITEMS/UNITS Nominal Voltage Input Voltage Range CE-1003 CE-1004 V DC12 V Vout+4V~DC16V Efficiency (min/typ) (*1) Maximum Current (*2) 83/88 85/90 A 1.5 Voltage Setting Accuracy (max) (*3) 3 Output Max Power Total Regulation (max) 5 Maximum Ripple Voltage (max/typ) (*4) mVp-p 100/30 Voltage Adjustable Range (*5) VDC Over Current Protection (typ) (*6) 1.5-3.3 3.3-5.0 A 2 Function Over Voltage Protection Not available Remote ON/OFF Control (*7) Available Operating Temperature -40 to +85 Storage Temperature -40 to +85 Operating Humidity Environment Storage Humidity RH 10-95 (the conditions of maximum 38 C in wet bulb temperature and non-condensation should be ensured.) RH 10-95 (the conditions of maximum 38 C in wet bulb temperature and non-condensation should be ensured.) Vibration CE-1003 10-2000Hz, 4 minutes sweep and 98m/s (10G) acceleration, 3 directions, 0.5h for each, in non-operation Vibration CE-1004 10-500Hz, 1 minute sweep and 98m/s (10G) acceleration or 1.5mm total amplitude, 3 directions, 0.5h for each, in non-operation Shock Mechanical 980m/s (100G), 6ms, 3 directions, 3 times for each, in non-operation Weight Size (W x H x D) g 1.8 mm 18.3 x 4.5 x 12.3 (*1) 5% max. when output voltage is set to 12V. In CE-1003: Vin=12V, Io=0.5A, Vout setting = 3.3V, Ta=25 C. In CE-1004: Vin=12V, Io=0.5A, Vout setting = 5.0V, Ta=25 C. (*2) Derating is needed when in use at CE-1003: 70 C or higher. CE-1004: No derating is needed. (*3) In Vin=12V, Io=0.5A, Ta=25 C. (*4) In 20MHz, Ta=25 C. (*5) 4V or higher difference between the input and output voltage is needed. (*6) Automatically resumes when output current becomes 0.5A or less. (*7) On voltage: 6V max. - 2V min., Off voltage: 0.6V max. - 0V min. With nominal input/output voltage, maximum output current, and Ta=25 C, if not specified separately. Outline Drawing 0.7 18.30.3 1.4 10 9 8 7 6 0.6 CE-10xx TDK-Lambda Made in Japan Lot No. P P P P 1 2 3 4 5 Recommended measurements for board mounting 12.30.3 Metal case 10-0.8 cut-through hole 4.5max. 1.4 1.4 15.7 20.1 P = 2.00.3 Allowable tolerance is 0.1 if not specified separately. Unit: mm Derating Curve Output power (%) 100 80 60 40 20 0 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 Ambient temperature ( C) Output power derating by ambient temperature All specifications are subject to change without notice. CE-1005 CE-1005 Specifications MODEL ITEMS/UNITS Nominal Voltage Input Voltage Range CE-1005 V DC3.3/5.0 V DC3.0-5.25 Efficiency (min/typ) (*1) Maximum Current (*2) 88.0/91.5 A 2.5 Voltage Setting Accuracy (max) (*3) 3 Output Max Power Total Regulation (max) 4 Maximum Ripple Voltage (max/typ) (*4) mVp-p 50/20 Voltage Adjustable Range (*5) VDC 1.0-3.3 Over Current Protection (typ) (*6) A 3 Function Over Voltage Protection Not available Remote ON/OFF Control (*7) Environment Available Operating Temperature -40 to +85 Storage Temperature -40 to +85 Operating Humidity RH 10-90 (the conditions of maximum 38 C in wet bulb temperature and non-condensation should be ensured.) Storage Humidity RH 10-90 (the conditions of maximum 38 C in wet bulb temperature and non-condensation should be ensured.) Vibration 10-2000Hz, 4 minutes sweep and 98m/s (10G) acceleration, 3 directions, 0.5h for each, in non-operation Shock Mechanical 980m/s (100G), 6ms, 3 directions, 3 times for each, in non-operation Weight Size (W x H x D) g 1.7 mm 18.3 x 4.2 x 12.3 (*1) 5% max. when output voltage is set to 12V. In Vin=3.3V, Io=1.5A, Vout setting = 2.5V, Ta=25 C. (*2) Derating is needed depending on the input voltage and the output voltage. (*3) In Vin=3.3V, Io=1.5A, Ta=25 C. (*4) In 20MHz, Ta=25 C. (*5) 1.0V~3.3V when Vin = 4.5V~5.25V, 1.0V~2.5V when Vin = 3.0V~4.5V (*6) Output is shut down if output voltage is lowered to 0.6V by operation of the protection circuit, and this status continues for 40ms or longer. Resumes by restarting input or resetting remote on/off after Vin is set to 1.2V or lower. (*7) On voltage: 0.5V max. - 0V min., Off voltage: 2V min. - Vin max. With nominal input/output voltage, maximum output current, and Ta=25 C, if not specified separately. Outline Drawing 0.7 Recommended measurements for board mounting 0.6 12.30.3 P P P P 1 2 3 4 5 10 9 CE-1005 8 TDK-Lambda MADE IN JAPAN 7 Lot No. 6 1.4 Metal case 10-0.8 cut-through hole 4.2max. 18.30.3 15.7 20.1 1.4 1.4 P = 2.00.3 Allowable tolerance is 0.1 if not specified separately. Unit: mm Derating Curve on the input voltage and the output voltage, as shown in the expressions below. When Vin = 3.0-3.6V Io1.25 + 0.5xVo When Vin = 3.6-5.25V Io0.83 + 0.67xVo 100 Output power (%) For maximum output current, derating is needed depending 80 60 40 20 0 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 Ambient temperature ( C) Output power derating by ambient temperature All specifications are subject to change without notice. CE-1005A CE-1005A Specifications MODEL ITEMS/UNITS Nominal Voltage Input Voltage Range CE-1005A V DC3.3/5.0 V DC3.0-5.25 (*1) Efficiency (min/typ) Maximum Current 88.0/93.0 A 2.5 Voltage Setting Accuracy (max) (*2) 3 Output Max Power Total Regulation (max) 4 Maximum Ripple Voltage (max/typ) (*3) mVp-p Voltage Adjustable Range 50/20 VDC Over Current Protection (typ) 0.9-3.3 A Available Function Over Voltage Protection Not available Remote ON/OFF Control (*4) Environment Available Operating Temperature -40 to +85 Storage Temperature -40 to +85 Operating Humidity RH 10-90 (the conditions of maximum 38 C in wet bulb temperature and non-condensation should be ensured.) Storage Humidity RH 10-90 (the conditions of maximum 38 C in wet bulb temperature and non-condensation should be ensured.) Vibration 10-2000Hz, 4 minutes sweep and 98m/s (10G) acceleration, 3 directions, 0.5h for each, in non-operation Shock Mechanical 980m/s (100G), 6ms, 3 directions, 3 times for each, in non-operation Weight Size (W x H x D) g 1.5 mm 18.3 x 4.2 x 12.3 (*1) Vin=5V,Io=2.5A,Vout=3.3V,Ta=25. (*2) Vin=5V,Io=2.5A,Ta=25. (*3) 100MHz,Ta=25. (*4) ON voltage: 0.5Vmax./0Vmin. OFF voltage: 2Vmin./Vin.max. With nominal input/output voltage, maximum output current, and Ta=25 C, if not specified separately. Outline Drawing Recommended measurements for board mounting 10-0.8 cut-through hole 10 9 8 7 6 0.6 CE-1005A TDK-Lambda MADE IN JAPAN Lot No. P P P P 1 2 3 4 5 12.30.3 Metal case 1.4 0.7 15.7 20.1 4.2max. 18.30.3 1.4 1.4 P = 2.00.3 Allowable tolerance is 0.1 if not specified separately. Unit: mm All specifications are subject to change without notice. CE-1050 CE-1050 Specifications MODEL ITEMS/UNITS Input Voltage Range CE-1050 V Efficiency (min/typ) (*1) Maximum Current (*2) DC9.0-26.4 85/90 A 2.5 Max Power Total Regulation (Vo : 3.3-5V)(max) Output 3.5 Max Power Total Regulation (Vo : 5-12.6V)(max) 5.0 Maximum Ripple Voltage ( Vo : 3.3-5V)(max/typ) (*3) mVp-p 50/25 Maximum Ripple Voltage ( Vo : 5-12.6V)(max/typ) (*3) mVp-p 100/50 Voltage Adjustable Range (*4) VDC 3.3-12.6 Over Current Protection (typ) (*5) A 3.5 Function Over Voltage Protection Not available Remote ON/OFF Control (*6) Environment Available Operating Temperature -40 to +85 Storage Temperature -40 to +85 Operating Humidity RH 10-90 (the conditions of maximum 38 C in wet bulb temperature and non-condensation should be ensured.) Storage Humidity RH 10-90 (the conditions of maximum 38 C in wet bulb temperature and non-condensation should be ensured.) Vibration 10-500Hz, 1 minute sweep and 98m/s (10G) acceleration or 1.5mm total amplitude, 3 directions, 0.5h for each, in non-operation Shock Mechanical 980m/s (100G), 6ms, 3 directions, 3 times for each, in non-operation Weight Size (W x H x D) g 3.74 mm 21.3 x 5.5 x 17.7 (*1) With 18V input voltage, 5V output voltage, and 2.5A output current. (*2) Derating is needed depending on the ambient temperature and the input voltage. (*3) In 20MHz, Ta=25 C, Vin=18V. (*4) 4V or higher difference between the input and output voltage is needed. (*5) Automatically resumes when output current becomes 1A or less. (*6) On voltage: 6V max. - 3V min., Off voltage: 0.4V max. - 0V min. With nominal input/output voltage, maximum output current, and Ta=25 C, if not specified separately. Outline Drawing 1.0 1.4 10 9 8 7 6 1.40.2 CE-1050 TDK-Lambda MADE IN JAPAN Lot No. 16.40.3 P P P P 17.7max. 1 2 3 4 5 Recommended measurements for board mounting 1.0 1.50.2 10-0.8 cut-through hole Metal case 18.3 22.7 21.30.3 0.1min. 5.5max. P = 20.2 Allowable tolerance is 0.2 if not specified separately. Unit: mm Vin24V Vin18V Vin12V 0 10 20 30 40 50 60 70 80 90 Ambient temperature 3.00 2.75 2.50 2.25 2.00 1.75 1.50 1.25 1.00 0.75 0.50 0.25 0.00 Vout=5.0V 2.00 Vout=9.0V 1.60 1.80 Vin24V Vin18V Vin12V 1.40 1.20 1.00 Vin24V Vin18V 0.80 0.60 0.40 0 10 20 30 40 50 60 70 80 90 Ambient temperature 0 10 20 30 40 50 60 70 80 90 Ambient temperature Output current derating by ambient temperature All specifications are subject to change without notice. 1.20 1.00 0.80 0.60 Vin24V Vin18V 0.40 0.20 0.20 0.00 Vout=12V 1.40 1.60 Output current (A) Vout=3.3V Output current (A) 3.00 2.75 2.50 2.25 2.00 1.75 1.50 1.25 1.00 0.75 0.50 0.25 0.00 Output current (A) Output current (A) Derating Curve 0.00 0 10 20 30 40 50 60 70 80 90 Ambient temperature CE-1003, -1004 Instruction Manual 1. CE-1003, -1004 1-1. Connection diagram 12V OFF ON 1 10 2 9 3 8 4 7 5 6 +Vout Vin 6V 4.7 Load 4.7 1-4. Start-up and operating conditions 0.5V 0V s 40ms Input start-up time 40ms or less 1-2. Terminal connections Number 1 2 3 4 5 6 7 8 9 10 Input-side inductance Lin : 22H or lower When adding inductance, add input CE-1003, -1004 Vin Vin GND GND ON/OFF GND Vs-0 Vs-1 Vs-2 Vout capacitor Cin simultaneously. Input-side capacitance Cin : Lin x 10 or higher Capacitance of the added capacitor should be 10 times or over the Lin value (Maximum ripple voltage may increase). Output-side added capacitance Cout : 100F or lower Start-up may not be possible if the capacitance is high. 1-5. Protection functions 1-3. Output voltage setting method To change the output voltage, short-circuit between the pins as shown below according to the voltage to be set. Vout CE-1003 3.3V 3.0V 2.8V 2.5V 2.3V 2.0V 1.8V 1.5V CE-1004 5.0V 4.8V 4.5V 4.3V 4.0V 3.8V 3.5V 3.3V Pin 7 Pin 8 Pin 9 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0Short-circuited to GND 1OPEN All specifications are subject to change without notice. Over output current protection is incorporated. If a current over the set value for the protection circuit flows, the output is lowered. It resumes automatically by lowering load current to 0.5A. (Start-up may not be possible in constant current load. Load current in start-up should be 0.5A or lower.) CE-1005 2. CE-1005 2-1. Connection diagram 2-4. Start-up and operating conditions To raise output voltage: Inserting Rex between 7 pin and 8 pin 3.3V 1 10 9 3 8 OFF 4 7 5 6 ON 4.7 Rex Load 2 10 Vin 3V 10 2 9 10 3 8 OFF 4 7 5 6 Rex 4.7 Load 1 ON s 40ms Input power supply start-up time To lower output voltage: Inserting Rex between 8 pin and 9 pin 3.3V 0.5V 0V 40ms or less Input-side inductance Lin : 4.7H or lower When adding inductance, add input capacitor Cin simultaneously. Input-side capacitance Cin : Lin x 10 or higher Capacitance of the added capacitor should be 10 times or over the Lin value (Maximum ripple voltage may increase). 2-2. Terminal connections Number 1 2 3 4 5 6 7 8 9 10 Output-side added capacitance Cout : 100F or lower Start-up may not be possible if the CE-1005 Vin Vin GND GND ON/OFF GND GND Vset Vout Vout capacitance is high. 2-5. Protection functions Over output current protection is incorporated. If a current over the set value for the protection circuit flows, the output is lowered. And if the output voltage is lowered to 0.6V continuously for 40ms, the output is shut down. To resume output, lower the input to 1.2V or lower once, and restart input. Or, turn the input Off by the On/Off terminal once, and then set it to on again. 2-3. Output voltage setting method To change the output voltage, calculate Rex by assigning the absolute value of the output voltage to Vo in the expression below, and attach it between the terminals to be connected. When in use with 2.5V output voltage, Rex does not need to be attached. Set voltage Terminals to be connected Expression 2.5V or higher 7-8 5.78-0.68xVout Rex = Vout-2.5 2.5V or lower 8-9 Rex = 5.78 xVout-1 2.5-Vout Unit: V, k All specifications are subject to change without notice. CE-10xx CE-1005A 3. CE-1005A 3-1. Connection diagram 3-4. Start-up and operating conditions To raise output voltage: Inserting Rex between 7 pin and 8 pin 3.3V 1 10 9 3 8 OFF 4 7 5 6 ON 22F Rex Load 2 22F Vin 3V 0.5V 0V s 40ms Input power supply start-up time To lower output voltage: Inserting Rex between 8 pin and 9 pin 10 2 9 22F 3 8 OFF 4 7 5 6 ON Rex 22F Load 1 3.3V 40ms or less Input-side inductance Lin : 4.7H or lower When adding inductance, add input capacitor Cin simultaneously. Input-side capacitance Cin : Lin x 10 or higher Capacitance of the added capacitor should be 10 times or over the Lin value (Maximum ripple voltage may increase). 3-2. Terminal connections Number 1 2 3 4 5 6 7 8 9 10 Output-side added capacitance Cout : 100F or lower Start-up may not be possible if the CE-1005A Vin Vin GND GND ON/OFF GND GND Vset Vout Vout capacitance is high. 3-5. Protection functions Over output current protection is incorporated. When a short circuit state was removed, returns to normal. 3-6. Difference with CE-1005 3-3. Output voltage setting method To change the output voltage, calculate Rex by assigning the absolute value of the output voltage to Vo in the expression below, and attach it between the terminals to be connected. When in use with 2.5V output voltage, Rex does not need to be attached. Set voltage Terminals to be connected Expression 1Vout3.3 7-8 18.3-5.1xVout Rex = Vout-1 0.9Vout1.0 8-9 Rex = 27.1xVout-18.3 1-Vout Unit: V, k All specifications are subject to change without notice. Exchange efficiency up (7585 Vin3.3V Vo1V/1.5A) An output low noise (4018mV Vin3.3V Vo1V/1.5A) Output voltage variable range expansion (1 to 3.30.9 to 3.3V) The initial output voltage value(2.51.0V) There is no temperature derating by the output voltage Product weight 12% reduction(1.71.5g) Oscillation frequency(550k600kHz fixed) CE-1050 CE-10xx 4. CE-1050 4-1. Connection diagram 4-4. Start-up and operating conditions To raise output voltage: Inserting Rex between 7 pin and 8 pin Vin 0.1F ON 10 2 9 3 8 4 7 5 6 Vin 8V Rex 0.1F Load OFF 1 0.5V 0V s 5ms Input start-up time: 5ms or less To lower output voltage: Inserting Rex between 8 pin and 9 pin Vin 0.1F ON 10 2 9 3 8 4 7 5 6 Rex 0.1F Load OFF 1 Input start-up time Vinrs : 5ms or less If this condition cannot be satisfied, use the On/Off terminal and start the unit in the condition with input voltage applied. Output can be started and stopped by controlling no. 5 terminal. As this pin is pulled up by 2A internal current source, the start-up time can be delayed by connecting a capacitor. Delay time is approximately 0.3ms per 1000pF. Input-side inductance Lin : 2.2H or lower When adding inductance, add input capacitor Cin simultaneously. Input-side capacitance Cin : Lin x 10 or higher Capacitance of the added capacitor should be 10 times or over the Lin value (Maximum ripple voltage may 4-2. Terminal connections Number 1 2 3 4 5 6 7 8 9 10 increase). Output-side added capacitance Cout : 100F or lower Start-up may not be possible if the Symbol Vin Vin GND GND ON/OFF GND GND Vset Vout Vout capacitance is high. It is not recommended to add inductance to the output side. 4-5. Protection functions Over output current protection is incorporated. If a current over the set value for the protection circuit flows, the output is lowered. The output resumes automatically when the load current is reduced to 1A or lower. 4-3. Output voltage setting method To change the output voltage, calculate Rex by assigning the absolute value of the output voltage to Vout in the expression below, and attach it between the terminals to be connected. When in use with 5V output voltage, Rex does not need to be attached. Set voltage Terminals to be connected Expression 5V or higher 7-8 13.31-Vout Rex = Vout-5 5V or lower 8-9 Rex = 7.8xVout-13.31 5-Vout Unit: V, k All specifications are subject to change without notice. 10 CE-10xx CE-1050 5. Notes on mounting and handling The connection diagrams in these handling instruc Recommended reflow soldering conditions tions represent the standard connection methods for methods. If the ripple voltage of the input power supply is high, or the ripple returned to input from the converter should be reduced, connect a capacitor with the ap propriate capacity and an appropriate inductor, accord ing to "Start-up and Operating Conditions" for each product in this instruction manual. If the maximum ripple & noise voltage should be re duced, connect a capacitor with appropriate capacity, according to "Start-up and Operating Conditions" for each product in this instruction manual. Series connection or parallel connection is not appli cable for this product. Surface temperature of parts this product. Consult us for use with other connection 245 225 195 150 40160s 60s max Reflow time Input fuse is not installed in this product. Reflow frequency:2 times (mounting on rear Do not use this product in an overload condition. Do ing so can cause failure. Preheating temperature: 150-195C, 40-160s Cleaning is not applicable for this product. Use low residue or non-cleaning flux. Notes on storage Keep this product indoors with little tem perature/humidity change and away from direct sunlight. Note that if this product is kept in a hot and humid condition or in a condition with drastic temperature changes, it can cause condensation, performance deterioration, or solderability deterio ration. CE-1050 uses multilevel boards. Observe the handling instructions described below. Otherwise, problems including pattern disconnection in reflow may occur (JEDEC MSL level 3). Baking process should be applied when 1 year or over has passed after delivery and the indicator value is 30% or over. Recommended baking conditions: 120C, for 120 minutes, 1 time only Used tape is not heat-resistant. Baking should be processed after detaching products from the tape. Baking when leaving the tape attached causes a change in shpae in the carrier tape. All specifications are subject to change without notice. panel not allowed) Soldering temperature: 245C or lower Solder melting temperature: 225 C or above, within 60s Hand soldering: Within 380C and 3s