SLLS318D - NOVEMBER 1998 - REVISED NOVEMBER 2007 D 3:21 Data Channel Expansion at up to D D D D D D D D D D D D 178.5 Mbytes/s Throughput Suited for SVGA, XGA, or SXGA Display Data Transmission From Controller to Display With Very Low EMI Three Data Channels and Clock Low-Voltage Differential Channels In and 21 Data and Clock Low-Voltage TTL Channels Out Operates From a Single 3.3-V Supply Tolerates 4-kV HBM ESD Packaged in Thin Shrink Small-Outline Package (TSSOP) With 20-Mil Terminal Pitch Consumes Less Than 1 mW When Disabled Wide Phase-Lock Input Frequency Range of 31 MHz to 68 MHz No External Components Required for PLL Inputs Meet or Exceed the Standard Requirements of ANSI EIA/TIA-644 Standard Improved Replacement for the DS90C364 and SN75LVDS86 Improved Jitter Tolerance See SN65LVDS86A-Q1 Data Sheet for Information About the Automotive Qualified Version DGG PACKAGE (TOP VIEW) D17 D18 GND D19 D20 NC LVDSGND A0M A0P A1M A1P LVDSVCC LVDSGND A2M A2P CLKINM CLKINP LVDSGND PLLGND PLLVCC PLLGND SHTDN CLKOUT D0 1 48 2 47 3 46 4 45 5 44 6 43 7 42 8 41 9 40 10 39 11 38 12 37 13 36 14 35 15 34 16 33 17 32 18 31 19 30 20 29 21 28 22 27 23 26 24 25 VCC D16 D15 D14 GND D13 VCC D12 D11 D10 GND D9 VCC D8 D7 D6 GND D5 D4 D3 VCC D2 D1 GND NC - Not connected description The SN65LVDS86A/SN75LVDS86A FlatLinkt receiver contains three serial-in 7-bit parallel-out shift registers and four low-voltage differential signaling (LVDS) line receivers in a single integrated circuit. These functions allow receipt of synchronous data from a compatible transmitter, such as the SN75LVDS81, '83, '84, or '85, over four balanced-pair conductors and expansion to 21 bits of single-ended low-voltage LVTTL synchronous data at a lower transfer rate. When receiving, the high-speed LVDS data is received and loaded into registers at seven times the LVDS input clock (CLKIN) rate. The data is then unloaded to a 21-bit-wide LVTTL parallel bus at the CLKIN rate. The 'LVDS86A presents valid data on the falling edge of the output clock (CLKOUT). The 'LVDS86A requires only four line-termination resistors for the differential inputs and little or no control. The data bus appears the same at the input to the transmitter and output of the receiver with the data transmission transparent to the user(s). The only user intervention is the possible use of the shutdown/clear (SHTDN) active-low input to inhibit the clock and shut off the LVDS receivers for lower power consumption. A low level on this signal clears all internal registers to a low level. The SN75LVDS86A is characterized for operation over ambient free-air temperatures of 0_C to 70_C. The SN65LVDS86A is characterized for operation over the full Automotive temperature range of - 40C to 125C. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. FlatLink is a trademark of Texas Instruments Incorporated. Copyright 2007, Texas Instruments Incorporated !"# $"% ! &#' &"! ! $#!! $# (# # #) "# && *+' &"! $!#, &# #!# + ! "&# #, $##' POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 SLLS318D - NOVEMBER 1998 - REVISED NOVEMBER 2007 functional block diagram Serial-In/ParallelOut Shift Register A0P A0M Serial In CLK A, B, ...G Serial-In/ParallelOut Shift Register A1P A1M D0 D1 D2 D3 D4 D5 D6 Serial In A, B, ...G CLK Serial-In/ParallelOut Shift Register A2P A2M Serial In D7 D8 D9 D10 D11 D12 D13 A, B, ...G CLK Control Logic SHTDN D14 D15 D16 D17 D18 D19 D20 Clock Generator CLK Clock In CLKINP CLKINM Clock Out Input Bus 2 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 CLKOUT CLKIN CC CC EEE EEE Previous Cycle D0-1 D6 A1 D7-1 A2 D14-1 CC CC EE EE Current Cycle A0 CLKOUT CC CC SLLS318D - NOVEMBER 1998 - REVISED NOVEMBER 2007 Next Cycle D5 D4 D3 D2 D1 D0 D6+1 D13 D12 D11 D10 D9 D8 D7 D13+1 D20 D19 D18 D17 D16 D15 D14 D20+1 EEE EEE CC CC EE EE Dn - 1 D0 CCC CCC CC CC Dn Dn + 1 Figure 1. SN65LVDS86A/SN75LVDS86A Load and Shift Timing Sequences equivalent input and output schematic diagrams VCC 300 k VCC 300 k 5 100 D Output 100 AnM AnP 7V 7V 7V VCC OUTPUT INPUT SHTDN 50 7V INPUT POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 3 SLLS318D - NOVEMBER 1998 - REVISED NOVEMBER 2007 absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Supply voltage range, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V to 4 V Voltage range at any terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V to VCC + 0.5 V Electrostatic discharge (see Note 2): All pins (Class 3A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 KV All pins (Class 2B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 V Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table Operating virtual junction temperature range, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40_C to 150_C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65_C to 150_C Lead temperature 1,6 mm (1/16 in) from case for 10 s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260_C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltage values are with respect to the GND terminals unless otherwise noted. 2. This rating is measured using MIL-STD-883C Method, 3015.7. DISSIPATION RATING TABLE PACKAGE TA 25C POWER RATING DERATING FACTOR ABOVE TA = 25C TA = 70C POWER RATING TA = 125C POWER RATING DGG 1637 mW 13.1 mW/C 1048 mW 327 mW This is the inverse of the junction-to-ambient thermal resistance when board mounted and with no air flow. recommended operating conditions (see Figure 2) MIN Supply voltage, VCC 3 High-level input voltage, VIH (SHTDN) 2 NOM MAX UNIT 3.6 V 3.3 V Low-level input voltage, VIL (SHTDN) Magnitude differential input voltage, |VID| 0.1 |V ID 2 Common-mode input voltage, VIC Operating free-air temperature, TA | 0.8 V 0.6 V 2.4 * |V ID 2 SN75LVDS86A 0 70 SN65LVDS86A -40 125 | V C timing requirements Cycle time, input clock, tc Parameter tc is defined as the mean duration of a minimum of 32 000 clock cycles. 4 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 MIN NOM MAX UNIT 14.7 tc 32.4 ns SLLS318D - NOVEMBER 1998 - REVISED NOVEMBER 2007 electrical characteristics over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS VIT+ Positive-going differential input threshold voltage VIT- Negative-going differential input threshold voltage VOH VOL High-level output voltage ICC IIH Disabled, All inputs to GND Enabled, AnM = 1.4 V, AnP = 1 V, tc = 15.38 ns UNIT 100 mV mV V 33 0.4 V 280 A 40 43 Enabled, CL = 8 pF, Worst-case pattern (see Figure 4) tc = 15.38 ns VIH = VCC High-level input current (SHTDN) MAX 2.4 Enabled, CL = 8 pF, Grayscale pattern (see Figure 3), tc = 15.38 ns Quiescent current (average) TYP -100 IOH = - 4 mA IOL = 4 mA Low-level output voltage MIN mA 68 20 SN75LVDS86A 20 SN65LVDS86A 25 A A A IIL Low-level input current (SHTDN) VIL = 0 II IOZ Input current A inputs 0 VI 2.4 V 20 A High-impedance output current VO = 0 or VCC 10 A All typical values are at VCC = 3.3 V, TA = 25C. The algebraic convention, in which the less-positive (more-negative) limit is designated minimum, is used in this data sheet for the negative-going input voltage threshold only. switching characteristics over recommended operating conditions (unless otherwise noted) PARAMETER tsu th TEST CONDITIONS Setup time, D0-D20 to CLKOUT CL = 8 pF, See Figure 5 Data hold time, CLKOUT to D0-D20 MIN TYP MAX UNIT 5 ns 5 ns t(RSKM) Receiver input skew margin (see Figure 7) tc = 15.38 ns ( 0.2%), |Input clock jitter| < 50 ps, td Delay time, CLKIN to CLKOUT (see Figure 7) VCC = 3.3 V, tc = 15.38 ns ( 0.2%), TA = 25C ten Enable time, SHTDN to phase lock See Figure 7 1 ms tdis Disable time, SHTDN to off state See Figure 8 400 ns tt tt Transition time, output (10% to 90% tr or tf) (data only) CL = 8 pF 3 ns Transition time, output (10% to 90% tr or tf) (clock only) CL = 8 pF 1.5 ns 550 700 3 5 ps 7 ns tw Pulse duration, output clock 0.50 tc ns All typical values are at VCC = 3.3 V, TA = 25C. The parameter t(RSKM) is the timing margin available to allocate to the transmitter and interconnection skews and clock jitter. The value of this parameter at clock periods other than 15.38 ns can be calculated from tRSKM = tc/14 - 550 ps. |Input clock jitter| is the magnitude of the change in input clock period. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 5 SLLS318D - NOVEMBER 1998 - REVISED NOVEMBER 2007 PARAMETER MEASUREMENT INFORMATION AP VIAP (VIAP + VIAM)/2 VID AM VIC VIAM Figure 2. Voltage Definitions CLKIN/CLKOUT D0, D6, D12 D1, D7, D13 D2, D8, D14 D3, D9, D15 D18, D19, D20 ALL OTHERS NOTE A: The 16-grayscale test-pattern test device power consumption for a typical display pattern. Figure 3. 16-Grayscale Test-Pattern Waveforms tc CLKIN/CLKOUT Even Dn Odd Dn NOTE A: The worst-case test pattern produces nearly the maximum switching frequency for all of the LVTTL outputs. Figure 4. Worst-Case Test-Pattern Waveforms 6 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SLLS318D - NOVEMBER 1998 - REVISED NOVEMBER 2007 PARAMETER MEASUREMENT INFORMATION tsu 70% VOH D0 -D20 30% VOH th 70% VOH CLKOUT 30% VOH Figure 5. Setup and Hold Time Waveforms POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 7 SLLS318D - NOVEMBER 1998 - REVISED NOVEMBER 2007 PARAMETER MEASUREMENT INFORMATION Tektronix HFS9003/HFS9DG1 Stimulus System (repeating patterns of 1110111 and 0001000) An D0 - D20 Device Under Test (DUT) CLKIN Tektronix Microwave Logic Multi-BERT-100RX Word Error Detector CLKOUT tc Internal Strobing Position 4 t t 7 c (RSKM) (see Note A) tsu1 th1 3 t t 7 c (RSKM) (see Note A) EEECC EEECC CCCEE CCCEE An and An EEECC EEECC CCCEE CCCEE CLKIN td tW CLKOUT tr < 1 ns 90% CLKIN or An 300 mV 0V 10% -300 mV tW td VOH 1.4 V VOL CLKOUT NOTE A: CLKIN is advanced or delayed with respect to data until errors are observed at the receiver outputs. The advance or delay is then reduced until there are no data errors observed. The magnitude of the advance or delay is t(RSKM). Figure 6. Receiver Input Skew Margin, Setup/Hold Time, and Delay Time Definitions 8 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SLLS318D - NOVEMBER 1998 - REVISED NOVEMBER 2007 PARAMETER MEASUREMENT INFORMATION CLKIN An ten SHTDN EEEEEEEEEEEEEEEEEEEEEEEEEE EEEEEEEEEEEEEEEEEEEEEEEEEE Dn Invalid Valid Figure 7. Enable Time Waveforms CLKIN tdis SHTDN CLKOUT Figure 8. Disable Time Waveforms POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 9 SLLS318D - NOVEMBER 1998 - REVISED NOVEMBER 2007 TYPICAL CHARACTERISTICS SUPPLY CURRENT vs CLOCK FREQUENCY 60 I CC - Supply Current - mA 55 VCC = 3.6 V 50 45 40 VCC = 3.3 V 35 Grayscale Data Pattern CL = 8 pF TA = 25C 30 VCC = 3 V 25 30 40 50 60 70 80 90 fclk - Clock Frequency - MHz Figure 9. RMS Grayscale ICC vs Clock Frequency 10 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SLLS318D - NOVEMBER 1998 - REVISED NOVEMBER 2007 APPLICATION INFORMATION Host Cable Flat Panel Display SN75LVDS84/5 Y0M 41 8 100 Y0P Y1M 40 9 39 10 100 Y1P Y2M 38 11 35 14 100 Y2P CLKOUTM 34 15 33 16 100 CLKOUTP 32 17 SN75LVDS86A/ SN65LVDS86A D0 A0M D1 D2 D3 A0P D4 D5 D6 A1M D7 D8 D9 A1P D10 D11 D12 A2M D13 D14 D15 A2P D16 D17 D18 CLKINM D19 D20 CLKOUT CLKINP Graphics Controller 24 26 27 29 30 31 33 34 35 37 39 40 41 43 45 46 47 1 2 4 5 23 12-BIT RED0 RED1 RED2 RED3 NA NA GREEN0 GREEN1 GREEN2 GREEN3 NA NA BLUE0 BLUE1 BLUE2 BLUE3 NA NA H_SYNC V_SYNC ENABLE CLOCK 18-BIT RED0 RED1 RED2 RED3 RED4 RED5 GREEN0 GREEN1 GREEN2 GREEN3 GREEN4 GREEN5 BLUE0 BLUE1 BLUE2 BLUE3 BLUE4 BLUE5 H_SYNC V_SYNC ENABLE CLOCK NOTES: A. The four 100- terminating resistors are recommended to be 0603 types. B. NA - not applicable, these unused inputs should be left open. Figure 10. 18-Bit Color Host to Flat Panel Display Application POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 11 SLLS318D - NOVEMBER 1998 - REVISED NOVEMBER 2007 APPLICATION INFORMATION Host Cable Flat Panel Display SN75LVDS81/83 Y0M 48 8 SN75LVDS86A/ SN65LVDS86A A0M 100 Y0P Y1M 47 9 46 10 A0P A1M 100 Y1P Y2M 45 11 42 14 A1P A2M 100 Y2P 41 15 40 16 CLKOUTM A2P CLKINM 100 CLKOUTP Y3M Y3P 39 17 CLKINP D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 D16 D17 D18 D19 D20 CLKOUT Graphics Controller 24 26 27 29 30 31 33 34 35 37 39 40 41 43 45 46 47 1 2 4 5 23 12-BIT RED0 RED1 RED2 RED3 NA NA GREEN0 GREEN1 GREEN2 GREEN3 NA NA BLUE0 BLUE1 BLUE2 BLUE3 NA NA H_SYNC V_SYNC ENABLE CLOCK 38 37 NOTES: A. The four 100- terminating resistors are recommended to be 0603 types. B. NA - not applicable, these unused inputs should be left open. Figure 11. 24-Bit Color Host to 18-Bit Color LCD Panel Display Application See the FlatLinkt Designer's Guide (SLLA012) for more application information. 12 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 18-BIT RED0 RED1 RED2 RED3 RED4 RED5 GREEN0 GREEN1 GREEN2 GREEN3 GREEN4 GREEN5 BLUE0 BLUE1 BLUE2 BLUE3 BLUE4 BLUE5 H_SYNC V_SYNC ENABLE CLOCK PACKAGE OPTION ADDENDUM www.ti.com 16-Jan-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) SN65LVDS86AQDGG ACTIVE TSSOP DGG 48 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR SN65LVDS86AQDGGR ACTIVE TSSOP DGG 48 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR SN75LVDS86ADGG ACTIVE TSSOP DGG 48 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR SN75LVDS86ADGGG4 ACTIVE TSSOP DGG 48 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR SN75LVDS86ADGGR ACTIVE TSSOP DGG 48 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR SN75LVDS86ADGGRG4 ACTIVE TSSOP DGG 48 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Samples (Requires Login) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 16-Jan-2012 In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF SN65LVDS86A : * Automotive: SN65LVDS86A-Q1 NOTE: Qualified Version Definitions: * Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant SN65LVDS86AQDGGR TSSOP DGG 48 2000 330.0 24.4 8.6 15.8 1.8 12.0 24.0 Q1 SN75LVDS86ADGGR TSSOP DGG 48 2000 330.0 24.4 8.6 15.8 1.8 12.0 24.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN65LVDS86AQDGGR TSSOP DGG 48 2000 367.0 367.0 45.0 SN75LVDS86ADGGR TSSOP DGG 48 2000 367.0 367.0 45.0 Pack Materials-Page 2 MECHANICAL DATA MTSS003D - JANUARY 1995 - REVISED JANUARY 1998 DGG (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 48 PINS SHOWN 0,27 0,17 0,50 48 0,08 M 25 6,20 6,00 8,30 7,90 0,15 NOM Gage Plane 1 0,25 24 0- 8 A 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,10 48 56 64 A MAX 12,60 14,10 17,10 A MIN 12,40 13,90 16,90 DIM 4040078 / F 12/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold protrusion not to exceed 0,15. Falls within JEDEC MO-153 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated