EH1300HSTS-84.000M REGULATORY COMPLIANCE 2011/65 (Data Sheet downloaded on Jan 23, 2019) 144 SVHC ITEM DESCRIPTION Quartz Crystal Clock Oscillators XO (SPXO) LVCMOS (CMOS) 3.3Vdc 8 Pin DIP Metal Thru-Hole 84.000MHz 100ppm 0C to +70C ELECTRICAL SPECIFICATIONS Nominal Frequency 84.000MHz Frequency Tolerance/Stability 100ppm Maximum (Inclusive of all conditions: Calibration Tolerance at 25C, Frequency Stability over the Operating Temperature Range, Supply Voltage Change, Ouput Load Change, 1st Year Aging at 25C, Shock, and Vibration.) Aging at 25C 5ppm/year Maximum Operating Temperature Range 0C to +70C Supply Voltage 3.3Vdc 10% Input Current 35mA Maximum (No Load) Output Voltage Logic High (Voh) 2.7Vdc Minimum (IOH = -8mA) Output Voltage Logic Low (Vol) 0.5Vdc Maximum (IOL = +8mA) Rise/Fall Time 4nSec Maximum (Measured at 20% to 80% of waveform) Duty Cycle 50 10(%) (Measured at 50% of waveform) Load Drive Capability 15pF Maximum Output Logic Type CMOS Pin 1 Connection Tri-State (Disabled Output: High Impedance) Tri-State Input Voltage (Vih and Vil) 70% of Vdd Minimum to enable output, 20% of Vdd Maximum to disable output (High Impedance), No Connect to enable output. Absolute Clock Jitter 250pSec Maximum, 100pSec Typical One Sigma Clock Period Jitter 50pSec Maximum, 40pSec Typical Start Up Time 10mSec Maximum Storage Temperature Range -55C to +125C ENVIRONMENTAL & MECHANICAL SPECIFICATIONS Fine Leak Test MIL-STD-883, Method 1014, Condition A Gross Leak Test MIL-STD-883, Method 1014, Condition C Lead Integrity MIL-STD-883, Method 2004 Mechanical Shock MIL-STD-202, Method 213, Condition C Resistance to Soldering Heat MIL-STD-202, Method 210 Resistance to Solvents MIL-STD-202, Method 215 Solderability MIL-STD-883, Method 2003 Temperature Cycling MIL-STD-883, Method 1010 Vibration MIL-STD-883, Method 2007, Condition A www.ecliptek.com | Specification Subject to Change Without Notice | 14 Pin DIP Revision C 12/01/2005 | 8 Pin DIP Revision C Ecliptek, LLC 5458 Louie Lane, Reno, NV 89511 1-800-ECLIPTEK or 714.433.1200 EH1300HSTS-84.000M MECHANICAL DIMENSIONS (all dimensions in millimeters) 7.620 0.203 1 7.620 0.203 8 0.8 0.1 (X3) 4 5 DIA 0.457 0.1 (X4) 5.08 MIN 5.6 MAX 13.2 MAX MARKING ORIENTATION 13.2 MAX PIN CONNECTION 1 Tri-State (High Impedance) 4 Case/Ground 5 Output 8 Supply Voltage LINE MARKING 1 ECLIPTEK 2 EH13TS EH13=Product Series 3 84.000M 4 XXYZZ XX=Ecliptek Manufacturing Code Y=Last Digit of the Year ZZ=Week of the Year www.ecliptek.com | Specification Subject to Change Without Notice | 14 Pin DIP Revision C 12/01/2005 | 8 Pin DIP Revision C Ecliptek, LLC 5458 Louie Lane, Reno, NV 89511 1-800-ECLIPTEK or 714.433.1200 EH1300HSTS-84.000M CLOCK OUTPUT TRI-STATE INPUT OUTPUT WAVEFORM & TIMING DIAGRAM VIH VIL VOH 80% of Waveform OUTPUT DISABLE (HIGH IMPEDANCE STATE) 50% of Waveform 20% of Waveform VOL tPLZ Fall Time Rise Time tPZL TW T Duty Cycle (%) = TW/T x 100 www.ecliptek.com | Specification Subject to Change Without Notice | 14 Pin DIP Revision C 12/01/2005 | 8 Pin DIP Revision C Ecliptek, LLC 5458 Louie Lane, Reno, NV 89511 1-800-ECLIPTEK or 714.433.1200 EH1300HSTS-84.000M Test Circuit for CMOS Output Frequency Counter Oscilloscope + + Power Supply _ Current Meter _ Supply Voltage (VDD) Probe (Note 2) Output + Voltage Meter _ 0.01F (Note 1) 0.1F (Note 1) Ground CL (Note 3) No Connect or Tri-State Note 1: An external 0.1F low frequency tantalum bypass capacitor in parallel with a 0.01F high frequency ceramic bypass capacitor close to the package ground and VDD pin is required. Note 2: A low capacitance (<12pF), 10X attenuation factor, high impedance (>10Mohms), and high bandwidth (>300MHz) passive probe is recommended. Note 3: Capacitance value CL includes sum of all probe and fixture capacitance. www.ecliptek.com | Specification Subject to Change Without Notice | 14 Pin DIP Revision C 12/01/2005 | 8 Pin DIP Revision C Ecliptek, LLC 5458 Louie Lane, Reno, NV 89511 1-800-ECLIPTEK or 714.433.1200 EH1300HSTS-84.000M Recommended Solder Reflow Methods High Temperature Solder Bath (Wave Solder) TS MAX to TL (Ramp-up Rate) Preheat - Temperature Minimum (TS MIN) - Temperature Typical (TS TYP) - Temperature Maximum (TS MAX) - Time (tS MIN) Ramp-up Rate (TL to TP) Time Maintained Above: - Temperature (TL) - Time (tL) Peak Temperature (TP) Target Peak Temperature (TP Target) Time within 5C of actual peak (tp) Ramp-down Rate Time 25C to Peak Temperature (t) Moisture Sensitivity Level 3C/Second Maximum 150C 175C 200C 60 - 180 Seconds 3C/Second Maximum 217C 60 - 150 Seconds 260C Maximum for 10 Seconds Maximum 250C +0/-5C 20 - 40 Seconds 6C/Second Maximum 8 Minutes Maximum Level 1 www.ecliptek.com | Specification Subject to Change Without Notice | 14 Pin DIP Revision C 12/01/2005 | 8 Pin DIP Revision C Ecliptek, LLC 5458 Louie Lane, Reno, NV 89511 1-800-ECLIPTEK or 714.433.1200 EH1300HSTS-84.000M Recommended Solder Reflow Methods Low Temperature Infrared/Convection 185C TS MAX to TL (Ramp-up Rate) Preheat - Temperature Minimum (TS MIN) - Temperature Typical (TS TYP) - Temperature Maximum (TS MAX) - Time (tS MIN) Ramp-up Rate (TL to TP) Time Maintained Above: - Temperature (TL) - Time (tL) Peak Temperature (TP) Target Peak Temperature (TP Target) Time within 5C of actual peak (tp) Ramp-down Rate Time 25C to Peak Temperature (t) Moisture Sensitivity Level 5C/Second Maximum N/A 150C N/A 60 - 120 Seconds 5C/Second Maximum 150C 200 Seconds Maximum 185C Maximum 185C Maximum 2 Times 10 Seconds Maximum 2 Times 5C/Second Maximum N/A Level 1 www.ecliptek.com | Specification Subject to Change Without Notice | 14 Pin DIP Revision C 12/01/2005 | 8 Pin DIP Revision C Ecliptek, LLC 5458 Louie Lane, Reno, NV 89511 1-800-ECLIPTEK or 714.433.1200 EH1300HSTS-84.000M Recommended Solder Reflow Methods Low Temperature Solder Bath (Wave Solder) TS MAX to TL (Ramp-up Rate) Preheat - Temperature Minimum (TS MIN) - Temperature Typical (TS TYP) - Temperature Maximum (TS MAX) - Time (tS MIN) Ramp-up Rate (TL to TP) Time Maintained Above: - Temperature (TL) - Time (tL) Peak Temperature (TP) Target Peak Temperature (TP Target) Time within 5C of actual peak (tp) Ramp-down Rate Time 25C to Peak Temperature (t) Moisture Sensitivity Level 5C/Second Maximum N/A 150C N/A 30 - 60 Seconds 5C/Second Maximum 150C 200 Seconds Maximum 245C Maximum 245C Maximum 1 Time / 235C Maximum 2 Times 5 Seconds Maximum 1 Time / 15 Seconds Maximum 2 Times 5C/Second Maximum N/A Level 1 Low Temperature Manual Soldering 185C Maximum for 10 Seconds Maximum, 2 times Maximum. High Temperature Manual Soldering 260C Maximum for 5 Seconds Maximum, 2 times Maximum. www.ecliptek.com | Specification Subject to Change Without Notice | 14 Pin DIP Revision C 12/01/2005 | 8 Pin DIP Revision C Ecliptek, LLC 5458 Louie Lane, Reno, NV 89511 1-800-ECLIPTEK or 714.433.1200