HIGH SPEED-10 MBit/s
LOGIC GATE OPTOCOUPLERS
HCPL-0600 HCPL-0601
1/7/04
Page 4 of 13
© 2004 Fairchild Semiconductor Corporation
** All typical values are at VCC = 5 V, TA = 25°C
1. The VCC supply to each optoisolator must be bypassed by a 0.1µF capacitor or larger. This can be either a ceramic or solid
tantalum capacitor with good high frequency characteristic and should be connected as close as possible to the package VCC
and GND pins of each device.
2. Enable Input - No pull up resistor required as the device has an internal pull up resistor.
3. tPLH - Propagation delay is measured from the 3.75 mA level on the HIGH to LOW transition of the input current pulse to the
1.5V level on the LOW to HIGH transition of the output voltage pulse.
4. tPHL - Propagation delay is measured from the 3.75 mA level on the LOW to HIGH transition of the input current pulse to the
1.5V level on the HIGH to LOW transition of the output voltage pulse.
5. tr - Rise time is measured from the 90% to the 10% levels on the LOW to HIGH transition of the output pulse.
6. tf - Fall time is measured from the 10% to the 90% levels on the HIGH to LOW transition of the output pulse.
7. tELH - Enable input propagation dela y is measured from the 1.5V le v el on the HIGH to LO W transition of the input v oltage pulse
to the 1.5V level on the LOW to HIGH transition of the output voltage pulse.
8. tEHL - Enable input propagation dela y is measured from the 1.5V le v el on the LO W to HIGH transition of the input v oltage pulse
to the 1.5V level on the HIGH to LOW transition of the output voltage pulse.
9. CMH - The maximum tolerable rate of rise of the common mode voltage to ensure the output will remain in the high state (i.e.,
VOUT > 2.0 V). Measured in volts per microsecond (V/µs).
10. CML - The maximum tolerable rate of fall of the common mode voltage to ensure the output will remain in the low output state
(i.e., V OUT < 0.8 V). Measured in volts per microsecond (V/µs).
11. Device considered a two-terminal device: Pins 1,2,3 and 4 shorted together, and Pins 5,6,7 and 8 shorted together.
TRANSFER CHARACTERISTICS (TA = -40°C to +85°C Unless otherwise specified.)
DC Characteristics Test Conditions Symbol Min Typ** Max Unit
High Level Output Current (VCC = 5.5 V, VO = 5.5 V)
(IF = 250 µA, VE = 2.0 V) (Note 2) IOH 100 µA
Low Level Output Voltage (VCC = 5.5 V, IF = 5 mA)
(VE = 2.0 V, IOL = 13 mA) (Note 2) VOL .35 0.6 V
Input Threshold Current (VCC = 5.5 V, VO = 0.6 V,
VE = 2.0 V, IOL = 13 mA) IFT 35mA
ISOLATION CHARACTERISTICS (TA = -40°C to +85°C Unless otherwise specified.)
Characteristics Test Conditions Symbol Min Typ** Max Unit
Input-Output
Insulation Leakage Current
(Relative humidity = 45%)
(TA = 25°C, t = 5 s)
(VI-O = 3000 VDC)
(Note 11)
II-O 1.0* µA
Withstand Insulation Test V oltage (RH < 50%, TA = 25°C)
(Note 11) ( t = 1 min.) VISO 2500 VRMS
Resistance (Input to Output) (VI-O = 500 V) (Note 11) RI-O 1012 Ω
Capacitance (Input to Output) (f = 1 MHz) (Note 11) CI-O 0.6 pF
NOTES