IS01DBFRGB Version (1) DISTINCTIVE CHARACTERISTICS * * * * * * * * * * * High resolution of 64 x 32 pixels 64 colors of backlighting can be controlled dynamically Display with LCD, RGB LED backlighting General brightness of backlight is dynamically controlled in eight steps from dark to bright Operated by commands and data supplied via serial communications (SPI) Can display as many as four lines of text with ten characters each Incorporates bitmap display function Programmable display graphics for alphanumeric characters and animated sequences Dual image VRAM for quick change of displayed images Low energy consumption Dust tight construction Viewing area: 13.9mm x 10.6mm (horizontal x vertical) Bracket has crimped legs to ensure secure PC mounting and prevent dislodging during wave soldering Actual Size NKK Switches * email: smartswitch@nkkswitches.com * Phone (480) 991-0942 * Fax (480) 998-1435 * www.nkksmartswitch.com 2 SMARTSWITCH TM DISPLAY DESCRIPTION Terminals LCD Mode LED Color LCD/LED Straight PC Black & White FSTN Positive Red/Green/Blue LCD SPECIFICATIONS Characteristics of Display Display Operation Mode FSTN positive; background colors, black & white Display Condition Transflective with built-in LED backlight Viewing Angle Direction 6 o'clock Viewing Area 13.9mm x 10.6mm (horizontal x vertical) Pixel Format 64 x 32 pixels (horizontal x vertical) Pixel Size 0.18mm x 0.24mm (horizontal x vertical) * Operating Temperature Range -15C ~ +50C (+5F ~ +122F) Storage Temperature Range -20C ~ +60C (-4F ~ +140F) Backlight LED RGB: red/green/blue * In a low temperature environment (below 0C), speed and contrast decrease when image changes. The non-indicator dot may become dense in a high temperature environment (about +50C). Absolute Maximum Ratings Items Recommended Operating Conditions Symbols Ratings Items Symbols Minimum Typical Maximum 4.9V 5.0V 5.1V Supply Voltage VDD -0.3V to +7.0V Supply Voltage VDD Input Voltage VI -0.3V to VD D +0.3V Input Voltage VI 0V -- VDD Output Voltage VO -0.3V to VD D +0.3V SPI Clock Frequency fSC K -- -- 8MHz Current Consumption I DD ** 10mA -- *** 50mA ** 10mA: Backlighting LED is off *** 50mA: Backlighting LEDs (Red, Green, Blue) are maximum brightness Optical Characteristics (Temperature at 25C) Items Symbols Min Typical Max Cr -- 3.0 -- Up & Down q -- 90 -- Right & Left f -- 90 -- Contrast Ratio Viewing Angle (Cr 1.1) NKK Switches * email: smartswitch@nkkswitches.com * Phone (480) 991-0942 * Fax (480) 998-1435 * www.nkksmartswitch.com 3 SMARTSWITCH TM BLOCK DIAGRAM & PIN CONFIGURATIONS Com1......Com32 Common Driver 32bit Shift Register 64 x 32 Dot Matrix LCD Panel seg1.......seg64 Segment Driver Backlight LED 64bit Shift Register Display Controller RAM #1 256Byte High Resolution SMARTDISPLAYTM with RGB LED and Black and White LCD Mode SCK 1 SS 2 SDI Green Blue RAM #2 256Byte LED Driver SPI SDO 3 Red 4 GND 5 VDD 6 Pin No. Symbol Name Function 1 SCK Serial Clock Clock line for SPI that synchronizes commands and data 2 SS Slave Select Chip select for SPI; line is active low 3 SDO Data Out Data output line for SPI 4 SDI Data In Data input line for SPI 5 GND Ground 6 VDD Power Power source for logic circuit and LCD TYPICAL DISPLAY DIMENSIONS (13.9) .547 (12.78) .503 See Pixel Detail (10.7) .421 (17.2) .677 Terminal numbers are not on the device. (10.0) .394 (1.3) .051 (0.5) Sq Typ .020 (16.8) .661 (4.0) .157 (8.3) .327 (10.6) .417 (0.65) Typ .026 Key (3.1) .122 (0.4) Typ .016 2 1 6 5 (14.7) .579 (2.0) Typ .079 (14.4) .567 (0.7) .028 (9.9) .390 (17.8) .701 (2.0) .079 (15.0) .591 (3.0) .118 CL (0.18) .007 (0.02) Typ .0008 (0.24) .009 Pixel Detail Footprint (16.8) .661 (2.0) Typ .079 4x (0.9) Dia .035 (3.1) .122 1 2 5 6 (10.0) .394 (15.0) .591 (2.0) .079 (4.0) .157 (14.7) .579 3x (0.9) Dia .035 6x (0.8) Dia .031 NKK Switches * email: smartswitch@nkkswitches.com * Phone (480) 991-0942 * Fax (480) 998-1435 * www.nkksmartswitch.com 4 SMARTSWITCH TM TIMING SPECIFICATIONS Circuit Example SPI Characteristics (See Timing Diagram) CLK_1 (Temperature at -15C ~ +50C and VDD = 5.0V 2%) Items SPI_SS Set Up Time Symbols Minimum ts S S 10ns SPI_SS Hold Time th S S SPI_CLK Cycle tc yc CK SPI_CLK Width thw CK 10ns SPI_DI Set Up Time ts D I 10ns SPI_DI Hold Time th D I 10ns SPI_DO Delay Time td D O 10ns Maximum SCK SDI SS SCK SDI SS SCK SDI IS_1 IS_2 IS_3 SCK SDI SS SCK SDI SS SCK SDI SS IS_4 IS_5 IS_6 SCK SDI SS SCK SDI SS SCK SDI SS SS CLK_2 10ns 8MHz CLK_3 IS_7 DATA_1 SPI Timing Chart (SS Using) IS_8 DATA_2 IS_9 DATA_3 SPI Timing Chart (SS Low Level Fixed) SS th SS t s SS Low SS tcy c CK t cy c CK t h w CK SCK t h DI SDI SCK ts DI t s DI SDI th DI D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 td DO SDO t d DO SDO thw CK D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 SDI and SCK shall be kept high when idle. BITMAP Segment Common COM1 COM2 1 2 3 4 5 6 7 8 9 * * * 16 ***** 49 * * * 56 57 58 59 60 61 62 63 64 Byte8 Byte7 *** Byte2 Byte1 D0 D1 D2 D3 D4 D5 D6 D7 D0 * * * D7 *** D0 * * * D7 D0 D1 D2 D3 D4 D5 D6 D7 Byte16 Byte9 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 * * * * * * * * * Byte256 COM32 *** *** D0 D1 D2 D3 D4 D5 D6 D7 Byte249 D0 D1 D2 D3 D4 D5 D6 D7 Transferring Display Data/Displaying LCD Command and Data Sequence Command Data (256 Bytes) 0 x 55 Byte1 Byte2 * * * Byte255 0 1 0 1 0 1 0 1 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 * * * D1 D0 Byte256 D7 D6 D5 D4 D3 D2 D1 D0 Notes: Display RAM has two screen areas. The first area is for the display on current LCD; the second area is for the data to be displayed next. The screens are changed when the second area is fully stored. NKK Switches * email: smartswitch@nkkswitches.com * Phone (480) 991-0942 * Fax (480) 998-1435 * www.nkksmartswitch.com 5 SMARTSWITCH TM COMMANDS & DATA * Transferring display data/displaying on LCD: command (1 Byte) + data (256 Bytes) * Others: command (1 Byte) + data (1 Byte) * Commands can be accepted only when all bits coincide; otherwise, they are not acknowledged * Additional commands will not be received until the communication of commands (1 Byte) and data (256 or 1 Byte) is completed * There is no time limit from the beginning to end of data receipt * Commands may be executed consecutively (no need to wait between commands) * Irregular commands or data are not recognized * Initial status at power activation: LCD display off, LED off (brightness 1/20, color off) Transferring Display Data/Displaying on LCD Command Hex Binary 0 x 55 01010101 Data Remarks 256 Bytes (64 x 32 = 2,048 bits) See below for details of bitmap data Data Remarks LED (Backlight) Color Set Command Hex 0 x 40 Binary 01000000 R R G G B B 1 1 2 bits x 3 For each of RGB: 00 = off 10 = 1/2 01 = 1/4 11 = full LED (Backlight) Brightness Set Command Hex 0 x 41 Data Binary 01000001 *** 1 1 1 1 1 3 bits Remarks For leading 3bits: 100 = 1/3 000 = 1/20 (dark) 101 = 1/2 110 = 2/3 001 = 1/10 111 = full 010 = 1/7 011 = 1/5 (bright) Reset (Returning to Initial Status at Power Activation) Command Hex Binary 0 x 5E 01011110 Data Remarks 00000011 Returning to initial status at power activation NKK Switches * email: smartswitch@nkkswitches.com * Phone (480) 991-0942 * Fax (480) 998-1435 * www.nkksmartswitch.com 6 SMARTSWITCH TM PRECAUTIONS FOR HANDLING & STORAGE OF LCD DEVICES ATTENTION ELECTROSTATIC SENSITIVE DEVICES Handling 1. The IS Series devices are electrostatic sensitive. 2. The IS series devices are not process sealed. 3. If the LCD is accidentally broken, avoid contact with the liquid and wash off any liquid spills to the skin or clothing. 4. Clean cap surface with dry cloth. If further cleaning is needed, wipe with dampened cloth using neutral cleanser and dry with clean cloth. Do not use organic solvent. 5. Recommended soldering time and temperature limits: 5 seconds maximum @ 270C maximum 6. Do not exceed 60C at the LCD level. Storage 1. Store in original container and away from direct sunlight. 2. Keep away from static electricity. 3. Avoid extreme temperatures, high humidity, gaseous substances, and all forms of chemical contamination. NKK Switches * email: smartswitch@nkkswitches.com * Phone (480) 991-0942 * Fax (480) 998-1435 * www.nkksmartswitch.com 7