General Note
BI Technologies reserves the right to make changes in product specification without notice or liability
© BI Technologies Limited • Glenrothes, Fife KY7 4NX, UK
Telephone: +44 (0) 1592 662200 • Facsimile: +44 (0) 1592 662299 • Website: www.bitechnologies.com • Email: sales@bitechnologies.co.uk
A subsidiary of TT electronics plc
627, 628 Series Issue Nov 2008
MODELS 627, 628
627, 628 Series
• .220” Small Outline
• Dual-In-Line
• Thick Film
• Surface Mount
• Resistor Networks
• RoHS Compliant
ELECTRICAL
ENVIRONMENTAL
Standard Resistance Range, Ohms 10 to 1Meg (Plus “0” Ohm Jumper)
Standard Resistance Tolerance, at 25°C ±2%(<33Ω = ±1 Ohm)
(Optional: F Tol. = ±1%)
Operating Temperature Range -55°C to +125°C
Temperature Coefficient of Resistance ±100ppm/°C (<100Ω = ±250ppm/°C)
Temperature Coefficient of Resistance, Tracking ±50ppm/°C
Maximum Operating Voltage 50Vdc or √PR
Insulation Resistance ≥10,000 Megohms
Thermal Shock plus Power Conditioning ∆R 0.70%
Short Time Overload ∆R 0.25%
Moisture Resistance ∆R 0.50%
Mechanical Shock ∆R 0.25%
Vibration ∆R 0.25%
Low Temperature Operation ∆R 0.25%
High Temperature Exposure ∆R 0.50%
Load Life, 2000 Hours (≤330Ω = ±0.5 Ohm) ∆R 0.50%
Resistance to Solder Heat (Total Immersion in solder at 280°C for 10 sec.) ∆R 0.25%
Dielectric Withstanding Voltage 200V for 1 minute
Temperature Exposure, Maximum 215°C for 3 minutes
Marking Permanency MIL-STD-202, Method 215
Lead Solderability MIL-STD-202, Method 208
Flammability UL-94V-0 Rated
Storage Temperature Range –55°C to +150°C
© BI Technologies Limited • Glenrothes, Fife KY7 4NX, UK
Telephone: +44 (0) 1592 662200 • Facsimile: +44 (0) 1592 662299 • Website: www.bitechnologies.com • Email: sales@bitechnologies.co.uk
627, 628 Series Issue Nov 2008
MODELS 627, 628
MECHANICAL
STANDARD RESISTANCE VALUES, OHMS
B Circuit (Bussed Resistors)
Ohms Code Ohms Code Ohms Code
22 220 1.2K 122 39K 393
33 330 1.5K 152 47K 473
39 390 1.8K 182 56K 563
47 470 2K 202 68K 683
56 560 2.2K 222 82K 823
68 680 2.7K 272 100K 104
82 820 3.3K 332 120K 124
100 101 3.9K 392 150K 154
120 121 4.7K 472 180K 184
150 151 5.6K 562 220K 224
180 181 6.8K 682 270K 274
220 221 8.2K 822 330K 334
270 271 10K 103 390K 394
330 331 12K 123 470K 474
390 391 15K 153 560K 564
470 471 18K 183 680K 684
560 561 20K 203 820K 824
680 681 22K 223 1 Meg 105
820 821 27K 273
1K 102 33K 333
Bold type represents stock standard values for ‘B’ Circuit
A Circuit (Isolated Resistors)
Ohms Code Ohms Code Ohms Code
22 220 1.2K 122 39K 393
33 330 1.5K 152 47K 473
39 390 1.8K 182 56K 563
47 470 2K 202 68K 683
56 560 2.2K 222 82K 823
68 680 2.7K 272 100K 104
82 820 3.3K 332 120K 124
100 101 3.9K 392 150K 154
120 121 4.7K 472 180K 184
150 151 5.6K 562 220K 224
180 181 6.8K 682 270K 274
220 221 8.2K 822 330K 334
270 271 10K 103 390K 394
330 331 12K 123 470K 474
390 391 15K 153 560K 564
470 471 18K 183 680K 684
560 561 20K 203 820K 824
680 681 22K 223 1 Meg 105
820 821 27K 273
1K 102 33K 333
Bold type represents stock standard values for ‘A’ Circuit
Ohms (R1/R2) Code (R1/R2) Marking Ohms (R1/R2) Code (R1/R2) Marking
120/120 121/121 45 330/470 331/471 10
150/150 151/151 40 390/390 391/391 42
180/300 181/301 31 470/470 471/471 43
220/220 221/221 39 1K/3.3K 102/332 35
220/330 221/331 08 3K/6.2K 302/662 13
270/270 271/271 41 6.8K/22K 682/223 29
330/390 331/391 09
J Circuit (Dual Terminators)
Lead Material 96-96.5%Sn, 3.5-4%Ag
Lead Configuration Gull Wing
Lead Coplanarity ±0.002 in. (0.051mm)
Substrate Material Alumina
Resistor Material Cermet
Body Material Epoxy
© BI Technologies Limited • Glenrothes, Fife KY7 4NX, UK
Telephone: +44 (0) 1592 662200 • Facsimile: +44 (0) 1592 662299 • Website: www.bitechnologies.com • Email: sales@bitechnologies.co.uk
627, 628 Series Issue Nov 2008
MODELS 627, 628
OUTLINE DIMENSIONS (Inch/mm)
Note: Maximum allowable mold excursion = 0.006”
SCHEMATICS
Note: Model 628: N = 16 Leads, Model 627: N = 14 Leads
SOLDER PAD LAYOUT (Inch/mm)
.395
10.03
.445
11.30
628 :
.310
7.87
.016
0.41 Typ.
Max.
Max.
627 : Max.
.050
1.27 Typ.
.090
2.29
.028
0.71
.008 ± .005
0.20 ± 0.13
.008
0.20
Typ.
Typ.
.220 ± .005
5.59 ± 0.13
Max.
A Circuit
Isolated Resistors
B Circuit
Bussed Resistors
J Circuit
Dual Terminator
N
1 N/2
N N
1 1 N/2 N/2
R1
R2
.220 ± .010
5.59 ± 0.25
.045 ± .005
1.14 ± 0.13
.030 ± .005
0.76 ± 0.13
.050
1.27 Typ.
.315
8.00 Min.
© BI Technologies Limited • Glenrothes, Fife KY7 4NX, UK
Telephone: +44 (0) 1592 662200 • Facsimile: +44 (0) 1592 662299 • Website: www.bitechnologies.com • Email: sales@bitechnologies.co.uk
627, 628 Series Issue Nov 2008
MODELS 627, 628
TYPICAL PART MARKING POWER DISSIPATION, WATTS AT 70°C
Model Package A B J
627 1.28 0.32 0.16 0.16
628 1.28 0.32 0.16 0.16
— Resistor (Per Circuit) —
PACKAGING
Standard: Tape & Reel
Conforms to requirements of EIA-481.
All units orientated with lead #1 to the left of direction of feed.
Tape: Width = 24mm
Pocket = Embossed Plastic, Antistatic
Pitch = 12mm
Reel: Diameter = 13” (300mm) Maximum
Capacity = 2,000 Units
Option: Magazines
Conforms to EIA and JEDEC standards.
All units orientated with lead #1 to the same side.
Magazine: Capacity = 50 Units
Part Part
Number: Marking:
628A330 8A330
628A331 8A331
628J221/331 8J08 Manufacturer’s Trademark
Date Code
Part Marking
Lead #1 Indicator
© BI Technologies Limited • Glenrothes, Fife KY7 4NX, UK
Telephone: +44 (0) 1592 662200 • Facsimile: +44 (0) 1592 662299 • Website: www.bitechnologies.com • Email: sales@bitechnologies.co.uk
627, 628 Series Issue Nov 2008
MODELS 627, 628
APPLICABLE DOCUMENTS
MIL-R-914 - Resistor Networks, Fixed, Film, Surface Mount Established Reliability General Specifications
MIL-STD-105 - Sampling Procedures and Tables for Inspection by Attributes
MIL-STD-202 - Test Methods for Electronics and Electrical Component Parts
EIA-481 - Carrier Taping of Surface Mount Components for Automatic Handling
EIA-PDP-100 - SOGN-0002 Outline Dimensions
ORDERING INFORMATION
62 8 J 331
/
471 F TR4
Standard Tape & Reel Packaging:
Model Series (No code used for magazines.)
Number of Leads: Tolerance Code:
7 = 14 Leads F = ±1%
8 = 16 Leads (No code used for 2% Std.)
Circuit Type: R2 Resistance Code:
A = Isolated (Add for J Circuit only.)
B = Bussed
J = Dual Terminator Resistance Code:
E12 & E24 Series: First two digits are significant.
Last digit denotes number of trailing zeros.
E96 Series: First three digits are significant.
Last digit denotes number of trailing zeros.
