SDRAM 64Mb H-die (x4, x8, x16) CMOS SDRAM
Rev. 1.4 November 2003
* Samsung Electronics reserves the right to change products or specification without notice.
Revision 1.4
November 2003
64Mb H-die SDRAM Specification
SDRAM 64Mb H-die (x4, x8, x16) CMOS SDRAM
Rev. 1.4 November 2003
Revision History
Revision 0.0 (May, 2003)
• Target spec release
Revision 0.1 (July, 2003)
• Preliminary spec release
Revision 0.2 (August, 2003)
• Modified IBIS characteristic.
Revision 1.0 (September, 2003)
• Finalized
Revision 1.1 (September, 2003)
• Corrected IBIS Specification.
Revision 1.2 (October, 2003)
• Deleted speed 7C at x4/x8.
Revision 1.3 (October, 2003)
• Deleted AC parameter notes 5.
Revision 1.4 (November, 2003)
• Modified Pin Function description.
SDRAM 64Mb H-die (x4, x8, x16) CMOS SDRAM
Rev. 1.4 November 2003
Part No. Orgainization Max Freq. Interface Package
K4S640432H-TC(L)75 16Mb x 4 133MHz(CL=3)
LVTTL 54pin TSOP(II)
K4S640832H-TC(L)75 8Mb x 8 133MHz(CL=3)
K4S641632H-TC(L)60 4Mb x 16 166MHz(CL=3)
K4S641632H-TC(L)70 143MHz(CL=3)
K4S641632H-TC(L)75 133MHz(CL=3)
The K4S640432H / K4S640832H / K4S641632H is 67,108,864 bits synchronous high data rate Dynamic RAM organized as 4 x
4,194,304 words by 4 bits, / 4 x 2,097,152 words by 8 bits, / 4 x 1,048,576 words by 16 bits, fabricated with SAMSUNGs high perfor-
mance CMOS technology. Synchronous design allows precise cycle control with the use of system clock I/O transactions are possible
on every clock cycle. Range of operating frequencies, programmable burst length and programmable latencies allow the same device to
be useful for a variety of high bandwidth, high performance memory system applications.
• JEDEC standard 3.3V power supply
• LVTTL compatible with multiplexed address
• Four banks operation
• MRS cycle with address key programs
-. CAS latency (2 & 3)
-. Burst length (1, 2, 4, 8 & Full page)
-. Burst type (Sequential & Interleave)
• All inputs are sampled at the positive going edge of the system
clock
• Burst read single-bit write operation
• DQM (x4,x8) & L(U)DQM (x16) for masking
• Auto & self refresh
• 64ms refresh period (4K cycle)
GENERAL DESCRIPTION
FEATURES
Ordering Information
4M x 4Bit x 4 / 2M x 8Bit x 4 / 1M x 16Bit x 4 Banks Synchronous DRAM
SDRAM 64Mb H-die (x4, x8, x16) CMOS SDRAM
Rev. 1.4 November 2003
11.76±0.20
0.463±0.008
0.002
0.05 MIN
0.008
0.21
± 0.002
± 0.05
0.020
0.50
( )
0.005-0.001
+0.003
0.125-0.035
+0.075
0.400
10.16
0.45~0.75
0.018~0.030
0.010
0.25 TYP
0~8°C
#54 #28
#1 #27
0.004
0.10 MAX
0.028
0.71
( ) 0.012
0.30 0.0315
0.80
0.047
1.20 MAX
0.039
1.00
± 0.004
± 0.10
0.891
22.62 MAX
0.875
22.22
± 0.004
± 0.10
+0.10
-0.05
+0.004
-0.002
54Pin TSOP(II) Package Dimension
Package Physical Dimension
SDRAM 64Mb H-die (x4, x8, x16) CMOS SDRAM
Rev. 1.4 November 2003
FUNCTIONAL BLOCK DIAGRAM
Bank Select
Data Input Register
4M x 4 / 2M x 8 / 1M x 16
4M x 4 / 2M x 8 / 1M x 16
Sense AMP
Output BufferI/O Control
Column Decoder
Latency & Burst Length
Programming Register
Address Register
Row Buffer
Refresh Counter
Row Decoder Col. Buffer
LRAS
LCBR
LCKE
LRAS LCBR LWE LDQM
CLK CKE CS RAS CAS WE L(U)DQM
LWE
LDQM
DQi
CLK
ADD
LCAS LWCBR
4M x 4 / 2M x 8 / 1M x 16
4M x 4 / 2M x 8 / 1M x 16
Timing Register
Samsung Electronics reserves the right to change products or specification without notice.
*
SDRAM 64Mb H-die (x4, x8, x16) CMOS SDRAM
Rev. 1.4 November 2003
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
PIN CONFIGURATION (Top view)
54Pin TSOP (II)
(400mil x 875mil)
(0.8 mm Pin pitch)
PIN FUNCTION DESCRIPTION
Pin Name Input Function
CLK System clock Active on the positive going edge to sample all inputs.
CS Chip select Disables or enables device operation by maski ng or enabling all input s except
CLK, CKE and DQM
CKE Clock enable Masks system clock to freeze operation from the next clock cycle.
CKE should be enabled at least one cycle prior to new command.
Disable input buffers for power down in standby.
A0 ~ A11 Address Row/column addresses are multiplexed on the same pins.
Row address : RA0 ~ RA11,
Column address : (x4 : CA0 ~ CA9, x8 : CA0 ~ CA8 , x16 : CA0 ~ CA7)
BA0 ~ BA1Bank select address Selects bank to be activated during row address latch time.
Selects bank for read/write during column address latch time.
RAS Row address strobe Latches row addresses on the positive going edge of the CLK with RAS low.
Enables row access & precharge.
CAS Column address strobe Latches column addresses on the positive going edge of the CLK with CAS low.
Enables column access.
WE Write enable Enables write operation and row precharge.
Latches data in starting from CAS , WE active.
DQM Data input/output mask Makes data output Hi-Z, tSHZ after the clock and masks the output.
Blocks data input when DQM active.
DQ0 ~ X15 Data input/output Data inputs/outputs are multiplexed on the same pins.
VDD/VSS Power supply/ground Power and ground for the input buffers and the core logic.
VDDQ/VSSQ Data output power/ground Isolated power supply and ground for the output buffers to provide improved noise
immunity.
N.C/RFU No connection
/reserved for future use This pin is recommended to be left No Connection on the device.
x16 x8 x4 x16
x8x4
VDD
DQ0
VDDQ
DQ1
DQ2
VSSQ
DQ3
DQ4
VDDQ
DQ5
DQ6
VSSQ
DQ7
VDD
LDQM
WE
CAS
RAS
CS
BA0
BA1
A10/AP
A0
A1
A2
A3
VDD
VSS
DQ15
VSSQ
DQ14
DQ13
VDDQ
DQ12
DQ11
VSSQ
DQ10
DQ9
VDDQ
DQ8
VSS
N.C/RFU
UDQM
CLK
CKE
N.C
A11
A9
A8
A7
A6
A5
A4
VSS
VDD
N.C
VDDQ
N.C
DQ0
VSSQ
N.C
N.C
VDDQ
N.C
DQ1
VSSQ
N.C
VDD
N.C
WE
CAS
RAS
CS
BA0
BA1
A10/AP
A0
A1
A2
A3
VDD
VSS
N.C
VSSQ
N.C
DQ3
VDDQ
N.C
N.C
VSSQ
N.C
DQ2
VDDQ
N.C
VSS
N.C/RFU
DQM
CLK
CKE
N.C
A11
A9
A8
A7
A6
A5
A4
VSS
VDD
DQ0
VDDQ
N.C
DQ1
VSSQ
N.C
DQ2
VDDQ
N.C
DQ3
VSSQ
N.C
VDD
N.C
WE
CAS
RAS
CS
BA0
BA1
A10/AP
A0
A1
A2
A3
VDD
VSS
DQ7
VSSQ
N.C
DQ6
VDDQ
N.C
DQ5
VSSQ
N.C
DQ4
VDDQ
N.C
VSS
N.C/RFU
DQM
CLK
CKE
N.C
A11
A9
A8
A7
A6
A5
A4
VSS
SDRAM 64Mb H-die (x4, x8, x16) CMOS SDRAM
Rev. 1.4 November 2003
ABSOLUTE MAXIMUM RATINGS
Parameter Symbol Value Unit
Voltage on any pin relative to VSS VIN, VOUT -1.0 ~ 4.6 V
Voltage on VDD supply relative to VSS VDD, VDDQ -1.0 ~ 4.6 V
Storage temperature TSTG -55 ~ +150 °C
Power dissipation PD1W
Short circuit current IOS 50 mA
Permanent device damage may occur if "ASOLUTE MAXIMUM RATINGS" are exceeded.
Functional operation should be restricted to recommended operating condition.
Exposure to higher than recommended voltage for extended periods of time could affect device reliability.
Note :
DC OPERATING CONDITIONS
Recommended operating conditions (Voltage referenced to VSS = 0V, TA = 0 to 70°C)
Parameter Symbol Min Typ Max Unit Note
Supply voltage VDD, VDDQ 3.0 3.3 3.6 V
Input logic high voltage VIH 2.0 3.0 VDD+0.3 V 1
Input logic low voltage VIL -0.3 0 0.8 V 2
Output logic high voltage VOH 2.4 - - V IOH = -2mA
Output logic low voltage VOL --0.4VIOL = 2mA
Input leakage current ILI -10 - 10 uA 3
1. VIH (max) = 5.6V AC.The overshoot voltage duration is 3ns.
2. VIL (min) = -2.0V AC. The undershoot voltage duration is 3ns.
3. Any input 0V VIN VDDQ.
Input leakage currents include Hi-Z output leakage for all bi-directional buffers with Tri-State outputs.
Notes :
CAPACITANCE (VDD = 3.3V, TA = 23°C, f = 1MHz, VREF =1.4V ± 200 mV)
Pin Symbol Min Max Unit Note
Clock CCLK 2.5 4.0 pF 1
RAS, CAS, WE, CS, CKE, DQM CIN 2.5 5.0 pF 2
Address CADD 2.5 5.0 pF 2
DQ0 ~ DQ3COUT 4.0 6.5 pF 3
1. -75 only specify a maximum value of 3.5pF
2. -75 only specify a maximum value of 3.8pF
3. -75 only specify a maximum value of 6.0pF
Notes :
SDRAM 64Mb H-die (x4, x8, x16) CMOS SDRAM
Rev. 1.4 November 2003
1. Measured with outputs open.
2. Refresh period is 64ms.
3. K4S6404(08)32H-TC**
4. K4S6404(08)32H-TL**
5. Unless otherwise noted, input swing IeveI is CMOS(VIH /VIL=VDDQ/VSSQ)
Notes :
(Recommended operating condition unless otherwise noted, TA = 0 to 70°C for x4, x8)
Parameter Symbol Test Condition Version Unit Note
75
Operating current
(One bank active) ICC1 Burst length = 1
tRC tRC(min)
IO = 0 mA 75 mA 1
Precharge standby current in
power-down mode ICC2P CKE VIL(max), tCC = 10ns 1 mA
ICC2PS CKE & CLK VIL(max), tCC = 1
Precharge standby current in
non power-down mode
ICC2NCKE VIH(min), CS VIH(min), tCC = 10ns
Input signals are changed one time during 20ns 15 mA
ICC2NS CKE VIH(min), CLK VIL(max), tCC =
Input signals are stable 6
Active standby current in
power-down mode ICC3P CKE VIL(max), tCC = 10ns 3 mA
ICC3PS CKE & CLK VIL(max), tCC = 3
Active standby current in
non power-down mode
(One bank active)
ICC3NCKE VIH(min), CS VIH(min), tCC = 10ns
Input signals are changed one time during 20ns 30 mA
ICC3NS CKE VIH(min), CLK VIL(max), tCC =
Input signals are stable 25
Operating current
(Burst mode) ICC4
IO = 0 mA
Page burst
4Banks Activated
tCCD = 2CLKs
115 mA 1
Refresh current ICC5 tRC tRC(min) 135 mA 2
Self refresh current ICC6 CKE 0.2V C1mA3
L 400 uA 4
DC CHARACTERISTICS
SDRAM 64Mb H-die (x4, x8, x16) CMOS SDRAM
Rev. 1.4 November 2003
1. Measured with outputs open.
2. Refresh period is 64ms.
3. K4S641632H-TC**
4. K4S641632H-TL**
5. Unless otherwise noted, input swing IeveI is CMOS(VIH /VIL=VDDQ/VSSQ)
Notes :
DC CHARACTERISTICS
(Recommended operating condition unless otherwise noted, TA = 0 to 70°C for x16 only)
Parameter Symbol Test Condition Version Unit Note
60 70 75
Operating current
(One bank active) ICC1 Burst length = 1
tRC tRC(min)
IO = 0 mA 140 115 110 mA 1
Precharge standby current in
power-down mode ICC2P CKE VIL(max), tCC = 10ns 1mA
ICC2PS CKE & CLK VIL(max), tCC = 1
Precharge standby current in
non power-down mode
ICC2NCKE VIH(min), CS VIH(min), tCC = 10ns
Input signals are changed one time during 20ns 15 mA
ICC2NS CKE VIH(min), CLK VIL(max), tCC =
Input signals are stable 6
Active standby current in
power-down mode ICC3P CKE VIL(max), tCC = 10ns 3mA
ICC3PS CKE & CLK VIL(max), tCC = 3
Active standby current in
non power-down mode
(One bank active)
ICC3NCKE VIH(min), CS VIH(min), tCC = 10ns
Input signals are changed one time during 20ns 30 mA
ICC3NS CKE VIH(min), CLK VIL(max), tCC =
Input signals are stable 25
Operating current
(Burst mode) ICC4
IO = 0 mA
Page burst
4Banks Activated
tCCD = 2CLKs
160 140 135 mA 1
Refresh current ICC5 tRC tRC(min) 160 140 135 mA 2
Self refresh current ICC6 CKE 0.2V C1mA 3
L400 uA 4
SDRAM 64Mb H-die (x4, x8, x16) CMOS SDRAM
Rev. 1.4 November 2003
AC OPERATING TEST CONDITIONS (VDD = 3.3V ± 0.3V, TA = 0 to 70°C)
Parameter Value Unit
AC input levels (Vih/Vil) 2.4/0.4 V
Input timing measurement reference level 1.4 V
Input rise and fall time tr/tf = 1/1 ns
Output timing measurement reference level 1.4 V
Output load condition See Fig. 2
3.3V
1200
870
Output
30pF
VOH (DC) = 2.4V, IOH = -2mA
VOL (DC) = 0.4V, IOL = 2mA
Vtt = 1.4V
50
Output
30pF
Z0 = 50
(Fig. 2) AC output load circuit (Fig. 1) DC output load circuit
Notes : 1. The minimum number of clock cycles is determined by dividing the minimum time required with clock cycle time
and then rounding off to the next higher integer.
2. Minimum delay is required to complete write.
3. All parts allow every cycle column address change.
4. In case of row precharge interrupt, auto precharge and read burst stop.
OPERATING AC PARAMETER
(AC operating conditions unless otherwise noted)
Parameter Symbol Version Unit Note
60 70 75
Row active to row active delay tRRD(min) 12 14 15 ns 1
RAS to CAS delay tRCD(min) 18 20 20 ns 1
Row precharge time tRP(min) 18 20 20 ns 1
Row active time tRAS(min) 42 49 45 ns 1
tRAS(max) 100 us
Row cycle time tRC(min) 60 68 65 ns 1
Last data in to row precharge tRDL(min) 2 CLK 2
Last data in to Active delay tDAL(min) 2 CLK + tRP -
Last data in to new col. address delay tCDL(min) 1 CLK 2
Last data in to burst stop tBDL(min) 1 CLK 2
Col. address to col. address delay tCCD(min) 1 CLK 3
Number of valid output data CAS latency = 3 2 ea 4
CAS latency = 2 1
SDRAM 64Mb H-die (x4, x8, x16) CMOS SDRAM
Rev. 1.4 November 2003
1. Parameters depend on programmed CAS latency.
2. If clock rising time is longer than 1ns, (tr/2-0.5)ns should be added to the parameter.
3. Assumed input rise and fall time (tr & tf) = 1ns.
If tr & tf is longer than 1ns, transient time compensation should be considered,
i.e., [(tr + tf)/2-1]ns should be added to the parameter .
Notes :
DQ BUFFER OUTPUT DRIVE CHARACTERISTICS
Parameter Symbol Condition Min Typ Max Unit Notes
Output rise time trh Measure in linear
region : 1.2V ~ 1.8V 1.37 4.37 Volts/ns 3
Output fall time tfh Measure in linear
region : 1.2V ~ 1.8V 1.30 3.8 Volts/ns 3
Output rise time trh Measure in linear
region : 1.2V ~ 1.8V 2.8 3.9 5.6 Volts/ns 1,2
Output fall time tfh Measure in linear
region : 1.2V ~ 1.8V 2.0 2.9 5.0 Volts/ns 1,2
1. Rise time specification based on 0pF + 50 to VSS, use these values to design to.
2. Fall time specification based on 0pF + 50 to VDD, use these values to design to.
3. Measured into 50pF only, use these values to characterize to.
4. All measurements done with respect to VSS.
Notes :
AC CHARACTERISTICS (AC operating conditions unless otherwise noted)
Parameter Symbol 60 70 75 Unit Note
Min Max Min Max Min Max
CLK cycle time CAS latency=3 tCC 61000 71000 7.5 1000 ns 1
CAS latency=2 - - 10
CLK to valid
output delay CAS latency=3 tSAC 565.4
ns 1,2
CAS latency=2 - - 6
Output data
hold time CAS latency=3 tOH 2.5 3 3 ns 2
CAS latency=2 - - 3
CLK high pulse width tCH 2.5 3 2.5 ns 3
CLK low pulse width tCL 2.5 3 2.5 ns 3
Input setup time tSS 1.5 2 1.5 ns 3
Input hold time tSH 110.8ns3
CLK to output in Low-Z tSLZ 111ns2
CLK to output
in Hi-Z CAS latency=3 tSHZ 565.4
ns
CAS latency=2 - - 6
SDRAM 64Mb H-die (x4, x8, x16) CMOS SDRAM
Rev. 1.4 November 2003
IOH Characteristics (Pull-up)
Voltage 133MHz
Min 133MHz
Max
(V) I (mA) I (mA)
3.45 - -1.68
3.30 - -19.11
3.00 -0.35 -51.87
2.70 -3.75 -90.44
2.50 -6.65 -107.31
1.95 -13.75 -137.9
1.80 -17.75 -158.34
1.65 -20.55 -173.6
1.50 -23.55 -188.79
1.40 -26.2 -199.01
1.00 -36.25 -241.15
0.20 -46.5 -351.68
IBIS SPECIFICATION
IOL Characteristics (Pull-down)
Voltage 133MHz
Min 133MHz
Max
(V) I (mA) I (mA)
3.45 43.92 155.82
3.30 - -
3.00 43.36 153.72
1.95 41.20 148.40
1.80 40.56 146.02
1.65 39.60 141.75
1.50 38.40 136.08
1.40 37.28 131.39
1.00 30.08 105.84
0.85 26.64 93.66
0.65 21.52 75.25
0.40 14.16 49.14
0
-100
-200
-300
-400
-500
-600
030.5 1 1.5 2 2.5 3.5
Voltage
mA
250
200
150
100
50
0030.5 1 1.5 2 2.5 3.5
Voltage
mA
133MHz Pull-up
133MHz Pull-down
IOH Min (133MHz)
IOH Max (133MHz)
IOL Min (133MHz)
IOL Max (133MHz)
SDRAM 64Mb H-die (x4, x8, x16) CMOS SDRAM
Rev. 1.4 November 2003
VDD Clamp @ CLK, CKE, CS, DQM & DQ
VDD (V) I (mA)
0.0 0.0
0.2 0.0
0.4 0.0
0.6 0.0
0.7 0.0
0.8 0.0
0.9 0.0
1.0 0.23
1.2 1.34
1.4 3.02
1.6 5.06
1.8 7.35
2.0 9.83
2.2 12.48
2.4 15.30
2.6 18.31
VSS Clamp @ CLK, CKE, CS, DQM & DQ
VSS (V) I (mA)
-2.6 -57.23
-2.4 -45.77
-2.2 -38.26
-2.0 -31.22
-1.8 -24.58
-1.6 -18.37
-1.4 -12.56
-1.2 -7.57
-1.0 -3.37
-0.9 -1.75
-0.8 -0.58
-0.7 -0.05
-0.6 0.0
-0.4 0.0
-0.2 0.0
0.0 0.0
20
15
10
5
00312
Voltage
mA
I (mA)
Voltage
mA
I (mA)
Minimum VDD clamp current
(Referenced to VDD)
Minimum VSS clamp current
0
-10
-20
-30
-40
-3 0-2 -1
-50
-60
SDRAM 64Mb H-die (x4, x8, x16) CMOS SDRAM
Rev. 1.4 November 2003
SIMPLIFIED TRUTH TABLE (V=V alid, X=Dont care, H=Logic high, L=Logic low)
Command CKEn-1 CKEn CS RAS CAS WE DQM BA0,1 A10/AP A11,
A9 ~ A0Note
Register Mode register set H X L L L L X OP code 1,2
Refresh
Auto refresh HHLL LHX X 3
Self
refresh
Entry L 3
Exit L H LHHHXX3
HX XX 3
Bank active & row addr. H X L L H H X V Row address
Read &
column address Auto precharge disable HXLHLHXVLColumn
address
(A0 ~ A9)
4
Auto precharge enable H 4,5
Write &
column address Auto precharge disable HXLHLLXVLColumn
address
(A0 ~ A9)
4
Auto precharge enable H 4,5
Burst stop H X L H H L X X 6
Precharge Bank selection HXLLHLX
VL X
All banks XH
Clock suspend or
active power down Entry H L HX XXXXLVVV
Exit L H X X X X X
Precharge power down mode Entry H L HX XXXX
LHHH
Exit L H HX XXX
LVVV
DQM H X V X 7
No operation command H X HX XXXX
LHHH
1. OP Code : Operand code
A0 ~ A11 & BA0 ~ BA1 : Program keys. (@ MRS)
2. MRS can be issued only at all banks precharge state.
A new command can be issued after 2 CLK cycles of MRS.
3. Auto refresh functions are as same as CBR refresh of DRAM.
The automatical precharge without row precharge command is meant by "Auto".
Auto/self refresh can be issued only at all banks precharge state.
4. BA0 ~ BA1 : Bank select addresses.
If both BA0 and BA1 are "Low" at read, write, row active and precharge, bank A is selected.
If both BA0 is "Low" and BA1 is "High" at read, write, row active and precharge, bank B is selected.
If both BA0 is "High" and BA1 is "Low" at read, write, row active and precharge, bank C is selected.
If both BA0 and BA1 are "High" at read, write, row active and precharge, bank D is selected.
If A10/AP is "High" at row precharge, BA0 and BA1 is ignored and all banks are selected.
5. During burst read or write with auto precharge, new read/write command can not be issued.
Another bank read/write command can be issued after the end of burst.
New row active of the associated bank can be issued at tRP after the end of burst.
6. Burst stop command is valid at every burst length.
7. DQM sampled at positive going edge of a CLK and masks the data-in at the very CLK (Write DQM latency is 0),
but makes Hi-Z state the data- out of 2 CLK cycles after. (Read DQM latency is 2)
Notes :