5200 Series NAND Flash SSD Features 5200 Series SATA NAND Flash SSD MTFDDAK240T, MTFDDAK480T, MTFDDAK960T, MTFDDAK1T9T, MTFDDAK3T8T, MTFDDAK7T6T Features * Reliability - MTTF: 3.0 million device hours3 - Static and dynamic wear leveling - Uncorrectable bit error rate (UBER): <1 sector per 1017 bits read - End-to-end data protection - Enhanced power-loss data protection with data protection capacitor monitoring * Self-monitoring, analysis, and reporting technology (SMART) command set * Capacity4 (unformatted): 240GB, 480GB, 960GB, 1920GB, 3840GB, 7680GB * Mechanical: - 2.5-inch x 7.0mm form factor * RoHS-compliant package * Secure field-upgradeable firmware with digitally signed firmware image * Power consumption: <6.0W (TYP, 5V only) * Operating temperature - Commercial (0C to 70C)5 * Micron(R) 3D TLC NAND Flash * Three performance/endurance levels - ECO - PRO - MAX * TCG Enterprise compliant self-encrypting drive (SED) * SATA 6 Gb/s interface * ATA modes supported - PIO mode 3, 4 - Multiword DMA mode 0, 1, 2 - Ultra DMA mode 0, 1, 2, 3, 4, 5, 6 * 512-byte sector size support * Hot-plug capable * Native command queuing support with 32-command slot support * ATA-8 ACS-3 revision 5 command set compliant * ATA security feature command set and password login support * Security erase command set: fast and secure erase * Performance (steady state)1 - Sequential 128KB read: Up to 540 MB/s - Sequential 128KB write: Up to 520 MB/s - Random 4KB read: Up to 95,000 IOPS - Random 4KB write: Up to 75,000 IOPS * Quality of Service2 - Read/Write (99.9%): 200s/300s (<2TB) - Read/Write (99.999%): 1000s/700s (<2TB) * Endurance4: Total bytes written (TBW) - Up to 17600TB CCMTD-731836775-10503 5200_series_ssd.pdf - Rev. E 05/18 EN Notes: 1. Performance varies by capacity and endurance. 2. 4KB transfers QD = 1 used for READ/WRITE latency values. 3. The product achieves a MTTF based on population statistics not relevant to individual units. 4. 1GB = 1 billion bytes. 5. As reported by SMART. Warranty: Contact your Micron sales representative for further information regarding the product, including product warranties. 1 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2017 Micron Technology, Inc. All rights reserved. Products and specifications discussed herein are subject to change by Micron without notice. 5200 Series NAND Flash SSD Features Part Numbering Information Micron's 5200 SSD is available in different configurations and densities. The chart below is a comprehensive list of options for the 5200 series devices; not all options listed can be combined to define an offered product. Visit micron.com for a list of valid part numbers. Figure 1: Part Number Chart MT FD D AK 960 T DC - 1 AT 6 AB YY ES Production Status Micron Technology Blank = Production ES = Engineering sample Product Family FD = Flash drive Customer Designator YY = Standard Drive Interface D = SATA 6.0 Gb/s Hardware Features AB = Standard TA = TAA Compliant Drive Form Factor AK = 2.5-inch (7mm) Drive Capacity Extended Firmware Features 240 = 240GB 480 = 480GB 960 = 960GB 1T9 = 1920GB 3T8 = 3840GB 7T6 = 7680GB Z = None 6 = SED TCG eSSC Sector Size 1 = 512 byte NAND Flash Component NAND Flash Type AT = 512Gb, TLC, x8, 3.3V (3D) T = TLC BOM Revision Product Family For example: 1 = 1st generation 2 = 2nd generation DC = 5200 ECO DD = 5200 PRO DN = 5200 MAX CCMTD-731836775-10503 5200_series_ssd.pdf - Rev. E 05/18 EN 1 2 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2017 Micron Technology, Inc. All rights reserved. 5200 Series NAND Flash SSD Important Notes and Warnings Important Notes and Warnings Micron Technology, Inc. ("Micron") reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions. This document supersedes and replaces all information supplied prior to the publication hereof. You may not rely on any information set forth in this document if you obtain the product described herein from any unauthorized distributor or other source not authorized by Micron. Automotive Applications. Products are not designed or intended for use in automotive applications unless specifically designated by Micron as automotive-grade by their respective data sheets. Distributor and customer/distributor shall assume the sole risk and liability for and shall indemnify and hold Micron harmless against all claims, costs, damages, and expenses and reasonable attorneys' fees arising out of, directly or indirectly, any claim of product liability, personal injury, death, or property damage resulting directly or indirectly from any use of nonautomotive-grade products in automotive applications. Customer/distributor shall ensure that the terms and conditions of sale between customer/distributor and any customer of distributor/customer (1) state that Micron products are not designed or intended for use in automotive applications unless specifically designated by Micron as automotive-grade by their respective data sheets and (2) require such customer of distributor/customer to indemnify and hold Micron harmless against all claims, costs, damages, and expenses and reasonable attorneys' fees arising out of, directly or indirectly, any claim of product liability, personal injury, death, or property damage resulting from any use of non-automotive-grade products in automotive applications. Critical Applications. Products are not authorized for use in applications in which failure of the Micron component could result, directly or indirectly in death, personal injury, or severe property or environmental damage ("Critical Applications"). Customer must protect against death, personal injury, and severe property and environmental damage by incorporating safety design measures into customer's applications to ensure that failure of the Micron component will not result in such harms. Should customer or distributor purchase, use, or sell any Micron component for any critical application, customer and distributor shall indemnify and hold harmless Micron and its subsidiaries, subcontractors, and affiliates and the directors, officers, and employees of each against all claims, costs, damages, and expenses and reasonable attorneys' fees arising out of, directly or indirectly, any claim of product liability, personal injury, or death arising in any way out of such critical application, whether or not Micron or its subsidiaries, subcontractors, or affiliates were negligent in the design, manufacture, or warning of the Micron product. Customer Responsibility. Customers are responsible for the design, manufacture, and operation of their systems, applications, and products using Micron products. ALL SEMICONDUCTOR PRODUCTS HAVE INHERENT FAILURE RATES AND LIMITED USEFUL LIVES. IT IS THE CUSTOMER'S SOLE RESPONSIBILITY TO DETERMINE WHETHER THE MICRON PRODUCT IS SUITABLE AND FIT FOR THE CUSTOMER'S SYSTEM, APPLICATION, OR PRODUCT. Customers must ensure that adequate design, manufacturing, and operating safeguards are included in customer's applications and products to eliminate the risk that personal injury, death, or severe property or environmental damages will result from failure of any semiconductor component. Limited Warranty. In no event shall Micron be liable for any indirect, incidental, punitive, special or consequential damages (including without limitation lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort, warranty, breach of contract or other legal theory, unless explicitly stated in a written agreement executed by Micron's duly authorized representative. General Description Micron's 5200 solid state drive (SSD) uses a single-chip controller with a SATA interface on the system side and four channels of Micron NAND Flash internally. Available in the 2.5-inch form factor, the SSD integrates easily in existing storage infrastructures. CCMTD-731836775-10503 5200_series_ssd.pdf - Rev. E 05/18 EN 3 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2017 Micron Technology, Inc. All rights reserved. 5200 Series NAND Flash SSD General Description The SSD is designed to use the SATA interface efficiently during both READs and WRITEs while delivering bandwidth-focused performance. SSD technology enables enhanced boot times, faster application load times, reduced power consumption and extended reliability. The self-encrypting drive (SED) features an AES-256 encryption engine, providing hardware-based, secure data encryption, with no loss of SSD performance. This SED follows the TCG Enterprise specification for trusted peripherals. When TCG Enterprise features are not enabled, the device can perform alternate data encryption by invoking the ATA security command set encryption features, to provide full disk encryption (FDE) managed in the host system BIOS. TCG Enterprise and ATA security feature sets cannot be enabled simultaneously. The data encryption is always running; however, encryption keys are not managed and the data is not secure until either TCG Enterprise or ATA security feature sets are enabled. Figure 2: Functional Block Diagram NAND SATA SSD controller NAND NAND NAND DRAM buffer CCMTD-731836775-10503 5200_series_ssd.pdf - Rev. E 05/18 EN 4 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2017 Micron Technology, Inc. All rights reserved. 5200 Series NAND Flash SSD Performance Performance Measured performance can vary for a number of reasons. The major factors affecting drive performance are the capacity of the drive and the interface/HBA of the host. Additionally, overall system performance can affect the measured drive performance. When comparing drives, it is recommended that all system variables are the same, and only the drive being tested varies. Performance numbers will vary depending on the host system configuration. Performance is measured using a single drive directly attached (no RAID) to an integrated SATA controller. Table 1: Drive Performance - ECO Capacity Parameter Unit 480GB 960GB 1920GB 3840GB 7680GB Sequential read (128KB transfer) 540 540 540 540 540 MB/s Sequential write (128KB transfer) 385 520 520 520 520 MB/s Random read (4KB transfer) 81,000 95,000 95,000 95,000 95,000 IOPS Random write (4KB transfer) 33,000 28,000 22,000 17,000 9500 IOPS Random 70/30 R/W (4KB transfer) 43,000 49,000 42,000 46,000 26,000 IOPS READ latency (99.9%) 200 200 200 200 200 s WRITE latency (99.9%) 300 300 300 500 900 s READ latency (99.999%) 1000 1000 1000 1000 1000 s WRITE latency (99.999%) 700 700 700 10,000 18,000 s Notes: 1. Performance measured using FIO with a queue depth of 32 in the steady state region. 2. 4KB transfers with a queue depth of 1 are used to measure READ/WRITE latency values. 3. System variations and HBA used will affect measured results. Table 2: Drive Performance - PRO Capacity Parameter Unit 960GB 1920GB 3840GB Sequential read (128KB transfer) 540 540 540 MB/s Sequential write (128KB transfer) 520 520 520 MB/s Random read (4KB transfer) 95,000 95,000 95,000 IOPS Random write (4KB transfer) 32,000 32,000 24,500 IOPS Random 70/30 R/W (4KB transfer) 53,000 53,000 57,000 IOPS READ latency (99.9%) 200 200 200 s WRITE latency (99.9%) 300 300 900 s READ latency (99.999%) 1000 1000 2000 s WRITE latency (99.999%) 700 700 18,000 s Notes: CCMTD-731836775-10503 5200_series_ssd.pdf - Rev. E 05/18 EN 1. Performance measured using FIO with a queue depth of 32 in the steady state region. 2. 4KB transfers with a queue depth of 1 are used to measure READ/WRITE latency values. 3. System variations and HBA used will affect measured results. 5 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2017 Micron Technology, Inc. All rights reserved. 5200 Series NAND Flash SSD Performance Table 3: Drive Performance - MAX Capacity Parameter Unit 240GB 480GB 960GB 1920GB Sequential read (128KB transfer) 540 540 540 540 MB/s Sequential write (128KB transfer) 310 460 520 520 MB/s Random read (4KB transfer) 81,000 93,000 95,000 95,000 IOPS Random write (4KB transfer) 53,000 70,000 75,000 70,000 IOPS Random 70/30 R/W (4KB transfer) 55,000 60,000 70,000 66,000 IOPS 200 200 200 200 s READ latency (99.9%) WRITE latency (99.9%) 300 300 300 300 s READ latency (99.999%) 2000 1000 1000 1000 s WRITE latency (99.999%) 700 700 700 700 s Notes: CCMTD-731836775-10503 5200_series_ssd.pdf - Rev. E 05/18 EN 1. Performance measured using FIO with a queue depth of 32 in the steady state region. 2. 4KB transfers with a queue depth of 1 are used to measure READ/WRITE latency values. 3. System variations and HBA used will affect measured results. 6 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2017 Micron Technology, Inc. All rights reserved. 5200 Series NAND Flash SSD Logical Block Address Configuration Logical Block Address Configuration The drive is set to report the number of logical block addresses (LBAs) that will ensure sufficient storage space for the specified capacity. Standard LBA settings, based on the IDEMA standard (LBA1-03), are shown below. Table 4: Standard LBA Settings - 512-Byte Sector Size Total LBA Capacity User Available Bytes Max LBA Decimal Hexadecimal Decimal Hexadecimal (Unformatted) 240GB 468,862,128 1BF244B0 468,862,127 1BF244AF 240,057,409,536 480GB 937,703,088 37E436B0 937,703,087 37E436AF 480,103,981,056 960GB 1,875,385,008 6FC81AB0 1,875,385,007 6FC81AAF 960,197,124,096 1920GB 3,750,748,848 DF8FE2B0 3,750,748,847 DF8FE2AF 1,920,383,410,176 3840GB 7,501,476,528 1BF1F72B0 7,501,476,527 1BF1F72AF 3,840,755,982,336 7680GB 15,002,931,888 37E3E92B0 15,002,931,887 37E3E92AF 7,681,501,126,656 Reliability Micron's SSDs incorporate advanced technology for defect and error management. They use various combinations of hardware-based error correction algorithms and firmware-based static and dynamic wear-leveling algorithms. Over the life of the SSD, uncorrectable errors may occur. An uncorrectable error is defined as data that is reported as successfully programmed to the SSD but is unable to be later read back without error. Table 5: Uncorrectable Bit Error Rate Uncorrectable Bit Error Rate Operation <1 sector per 1017 bits READ Mean Time to Failure Mean time to failure (MTTF) for the SSD can be predicted based on the component reliability data using the methods referenced in the Telcordia SR-332 reliability prediction procedures for electronic equipment. Table 6: MTTF Capacity MTTF (Operating Hours) All capacities Note: CCMTD-731836775-10503 5200_series_ssd.pdf - Rev. E 05/18 EN 3.0 million 1. The product achieves a MTTF of 3.0 million hours based on population statistics not relevant to individual units. 7 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2017 Micron Technology, Inc. All rights reserved. 5200 Series NAND Flash SSD Reliability Endurance Endurance for the SSD can be predicted based on the usage conditions applied to the device, the internal NAND component cycles, the write amplification factor, and the wear-leveling efficiency of the drive. Total bytes written measured with 55C case temperature within the total bytes written values listed in this document. The table below shows the drive lifetime for each SSD capacity based on predefined usage conditions. Table 7: Drive Lifetime Drive Lifetime (Total Bytes Written) Capacity Notes: CCMTD-731836775-10503 5200_series_ssd.pdf - Rev. E 05/18 EN ECO PRO MAX Unit 240GB - - 2200 TB 480GB 870 - 4380 960GB 1750 2270 8760 1920GB 3500 5950 17520 3840GB 7700 17600 - 7680GB 8400 - - 1. Total bytes written were calculated assuming drive is 100% full (user capacity) and a workload of 100% random, aligned 4KB writes. 2. 1TB = 1,000,000,000,000 8 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2017 Micron Technology, Inc. All rights reserved. 5200 Series NAND Flash SSD Electrical Characteristics Electrical Characteristics Stresses greater than those listed may cause permanent damage to the device. This is a stress rating only, and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. Table 8: SATA Power Consumption (5V Only) - 2.5-inch Idle Average Sequential Write (128KB transfer) Sequential Read (128KB transfer) 240GB 1.5W 3.0W 2.5W 480GB 1.5W 3.1W 2.5W 960GB 1.5W 3.4W 2.8W 1920GB 1.5W 3.6W 3.0W 3840GB 1.5W 3.3W 2.5W 7680GB 1.5W 3.3W 2.5W Capacity Notes: 1. Data taken at 25C using a 6 Gb/s SATA interface. 2. Sequential power measured during FIO with 128KB transfer, RMS average over a 500ms window. Table 9: Maximum Ratings Parameter/Condition Symbol Min Max Unit V12 10.8 13.2 V V5 4.5 5.5 V TC 0 70 C Non-operating temperature - -40 85 C Rate of temperature change - - 20 C/hour Relative humidity (non-condensing) - 5 95 % Voltage input Operating (2.5-inch)1 temperature2 Notes: 1. 5V supply required; 12V supply optional 2. Based upon drive temperature reported by SMART Table 10: Shock and Vibration Parameter/Condition Specification Non-operating shock 1500G/0.5ms Rotary vibration, non-operating CCMTD-731836775-10503 5200_series_ssd.pdf - Rev. E 05/18 EN 5-800Hz at 3.13 Grms 9 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2017 Micron Technology, Inc. All rights reserved. 5200 Series NAND Flash SSD Device ID Device ID Table 11: Identify Device See Note 1 for setting definitions Word Bit(s) Setting 0 Default Value Description - - - 15 F 0b General configuration bit-significant information 14-8 X 0000100b 7-6 X 01b Obsolete 5-3 X 000b Retired 2 V 0b Response incomplete 1 X 0b Retired 0 F 0b Reserved 1 - X 3FFFh Obsolete 2 - F C837h Specific configuration 3 - X 0010h Obsolete 4-5 - X 0000h 0000h 0 = ATA device Retired Retired 6 - X 003Fh 7-8 - V 0000h 0000h 9 - X 0000h Retired 10-19 - F Varies Serial number (20 ASCII characters) 20-22 - X 23-26 - F Varies Firmware revision (8 ASCII characters) 27-46 - F Varies Model number (40 ASCII characters) 47 15-8 F 80h 80h 7-0 F 10h 00h = Reserved 01h-FFh = Maximum number of logical sectors that shall be transferred per DRQ data block on READ/WRITE MULTIPLE commands - - - 15 F 0b Shall be cleared to zero 14 F 1b Shall be set to one 13-1 F 0000000000000b 0 F 0b/1b 48 CCMTD-731836775-10503 5200_series_ssd.pdf - Rev. E 05/18 EN Obsolete Reserved for assignment by the CompactFlashTM Association 0000h 0000h 0000h Retired/obsolete Trusted Computing feature set options Reserved for the Trusted Computing Group 1 = Trusted Computing feature set is supported This bit will be 1 for TCG drives, otherwise 0 10 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2017 Micron Technology, Inc. All rights reserved. 5200 Series NAND Flash SSD Device ID Table 11: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting 49 50 Default Value Description Capabilities - - - 15-14 F 00b Reserved for the IDENTIFY PACKET DEVICE command 13 F 1b 1 = Standby timer values as specified in this standard are supported 0 = Standby timer values shall be managed by the device 12 F 0b Reserved for the IDENTIFY PACKET DEVICE command 11 F 1b 1 = IORDY is supported 0 = IORDY may be supported 10 F 1b 1 = IORDY may be disabled 9 F 1b 1 = LBA is supported 8 F 1b 1 = DMA is supported 7-2 F 000000b 1-0 V 00b Reserved Long physical sector alignment error reporting - - - 15 F 0b Shall be cleared to zero 14 F 1b Shall be set to one 13-2 F 000000000000b Reserved 1 X 0b Obsolete 0 F 1b Shall be set to one to indicate a vendor-specific standby timer value minimum 51-52 - X 0000h 0000h 53 15-8 V 00h 7-3 F 00000b 2 F 1b 1 = The fields reported in word 88 are valid 0 = The fields reported in word 88 are not valid 1 F 1b 1 = The fields reported in words (70:64) are valid 0 = the fields reported in words (70:64) are not valid 0 X 0b Obsolete - X 3FFFh 0010h 003Fh FC10h 00FBh Obsolete 54-58 CCMTD-731836775-10503 5200_series_ssd.pdf - Rev. E 05/18 EN Capabilities Obsolete Free-fall control sensitivity: 00h = Vendor's recommended setting 01h-FFh = Sensitivity level Reserved 11 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2017 Micron Technology, Inc. All rights reserved. 5200 Series NAND Flash SSD Device ID Table 11: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting 59 Default Value Description 15 F 1b 1 = The BLOCK ERASE EXT command is supported 14 F 1b 1 = The OVERWRITE EXT command is supported 13 F 1b 1 = The CRYPTO SCRAMBLE EXT command is supported 12 F 1b 1 = The sanitize feature set is supported 11 F 1b 1 = The commands allowed during a sanitize operation are specified by ACS-3 10 F 1b The SANITIZE ANTIFREEZE LOCK EXT command is supported 9 F 0b Reserved 8 V 1b 1 = Multiple sector settings are valid 7-0 V 00010000b xxh = Current setting for number of logical sectors that shall be transferred per DRQ data block on READ/WRITE MULTIPLE commands - F FFFFh 0FFFh Total number of user addressable logical sectors for 28-bit commands 62 - X 0000h Obsolete 63 15-11 F 00000b Reserved 10 V 0b 1 = Multiword DMA mode 2 is selected 0 = Multiword DMA mode 2 is not selected 9 V 0b 1 = Multiword DMA mode 1 is selected 0 = Multiword DMA mode 1 is not selected 8 V 0b 1 = Multiword DMA mode 0 is selected 0 = Multiword DMA mode 0 is not selected 7-3 F 00000b 2 F 1b 1 = Multiword DMA mode 2 and below are supported 1 F 1b 1 = Multiword DMA mode 1 and below are supported 1 = Multiword DMA mode 0 is supported 60-61 Reserved 0 F 1b 15-2 F 00000000000000b 1 F 1b PIO mode 4 supported 0 F 1b PIO mode 3 supported 65 - F 0078h Minimum Multiword DMA transfer cycle time per word Cycle time in nanoseconds 66 - F 0078h Manufacturer's recommended Multiword DMA transfer cycle time Cycle time in nanoseconds 67 - F 0078h Minimum PIO transfer cycle time without flow control Cycle time in nanoseconds 68 - F 0078h Minimum PIO transfer cycle time with IORDY flow control Cycle time in nanoseconds 64 CCMTD-731836775-10503 5200_series_ssd.pdf - Rev. E 05/18 EN Reserved 12 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2017 Micron Technology, Inc. All rights reserved. 5200 Series NAND Flash SSD Device ID Table 11: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting 69 Default Value Description - F - Additional supported 15 F 0b Reserved for CFA 14 F 1b 1 = Deterministic read after trim is supported 13 F 0b 1 = Long physical sector alignment error reporting control is supported 12 X 0b Obsolete 11 F 1b 1 = READ BUFFER DMA is supported 10 F 1b 1 = WRITE BUFFER DMA is supported 9 X 0b Obsolete 8 F 1b 1 = DOWNLOAD MICROCODE DMA is supported 7 F 0b Reserved for IEEE-1667 6 F 0b 0 = Optional ATA device 28-bit commands are supported 5 F 1b 1 = Read zero after trim is supported 4 F 0b/1b 3 F 0b 1 = Extended number of user addressable sectors is supported (words 230 - 233) 1 = Device encrypts all user data This bit will be 1 for TCG drives, otherwise 0 2 F 0b All write cache is nonvolatile 1-0 - 00b Reserved 70 - F 0000h Reserved 71-74 - F 75 0000h 0000h 0000h Reserved for the IDENTIFY PACKET DEVICE command 0000h - - - 15-5 F 00000000000b 4-0 F 11111b CCMTD-731836775-10503 5200_series_ssd.pdf - Rev. E 05/18 EN Queue depth Reserved Maximum queue depth - 1 13 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2017 Micron Technology, Inc. All rights reserved. 5200 Series NAND Flash SSD Device ID Table 11: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting 76 77 78 Default Value Description - - - Serial ATA capabilities 15 F 1b 1 = Supports READ LOG DMA EXT as equivalent to READ LOG EXT 14 F 0b 1 = Supports Device automatic partial to slumber transitions 13 F 0b 1 = Supports host automatic partial to slumber transitions 12 F 1b Native command queuing priority information is supported 11 F 0b Unload while NCQ commands are outstanding is supported 10 F 1b SATA physical event counter log is supported 9 F 0b 1 = Receipt of host-initiated interface power management requests is supported 8 F 1b Native command queuing is supported 7-4 F 0000b 3 F 1b 1 = Serial ATA Gen-3 speed (6.0 Gb/s) is supported 2 F 1b 1 = Serial ATA Gen-2 speed (3.0 Gb/s) is supported 1 F 1b 1 = Serial ATA Gen-1 speed (1.5 Gb/s) is supported 0 F 0b Reserved (set to 0) Reserved for future Serial ATA signaling speed grades - - - 15-7 - 000000000b Serial ATA additional capabilities 6 F 0b 1 = Supports RECEIVE FPDMA QUEUED and SEND FPDMA QUEUED commands 5 F 0b NCQ QUEUE MANAGEMENT command is supported NCQ streaming is supported Reserved for Serial ATA 4 F 0b 3-1 V Varies 0 F 0b - - - 15-8 - 00000000b 7 F 0b 1 = Device supports NCQ autosense 6 F 1b 1 = Supports software settings preservation 5 F 0b 1 = Device supports hardware feature control 4 F 0b 1 = In-order data delivery is supported 3 F 0b 1 = Device-initiated interface power management is supported 2 F 1b 1 = DMA setup auto-activate optimization is supported 1 F 0b 1 = Non-zero buffer offsets in DMA setup FIS are supported 0 F 0b Reserved (set to 0) CCMTD-731836775-10503 5200_series_ssd.pdf - Rev. E 05/18 EN Coded value indicating current negotiated Serial ATA signal speed Shall be cleared to zero Serial ATA features are supported Reserved for Serial ATA 14 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2017 Micron Technology, Inc. All rights reserved. 5200 Series NAND Flash SSD Device ID Table 11: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting 79 80 81 82 Default Value Description - - - Serial ATA features are enabled 15-8 - 00000000b 7 V 0b 1 = Automatic partial to slumber transitions are enabled 6 V 1b 1 = Software settings preservation is enabled 5 V 0b 1 = Hardware feature control is enabled 4 V 0b 1 = In-order data delivery is enabled 3 V 0b 1 = Device-initiated interface power management is enabled 2 V 0b 1 = DMA setup auto-activate optimization is enabled 1 V 0b 1 = Non-zero buffer offsets in DMA setup FIS is enabled 0 V 0b Reserved (set to 0) Reserved for Serial ATA - - - 15-12 F 0000b Major revision number 11 F 0b 1 = ATA8-ACS4 is supported 10 F 1b 1 = ATA8-ACS3 is supported 9 F 1b 1 = ATA8-ACS2 is supported 8 F 1b 1 = ATA8-ACS is supported 7 F 1b 1 = ATA/ATAPI-7 is supported 6 F 1b 1 = ATA/ATAPI-6 is supported 1 = ATA/ATAPI-5 is supported Reserved 5 F 1b 4-1 X 1100b Obsolete 0 - 0b Reserved - F 006Dh Minor revision number - - - 15 X 0b Command and feature sets are supported Obsolete 14 F 1b 1 = NOP command is supported 13 F 1b 1 = READ BUFFER command is supported 12 F 1b 1 = WRITE BUFFER command is supported 11-10 X 00b Obsolete 9 F 0b 1 = DEVICE RESET command is supported 8-7 X 00b Obsolete 6 F 1b 1 = Read look-ahead is supported 5 F 1b 1 = Write cache is supported 4 F 0b Shall be cleared to zero to indicate that the packet feature set is not supported 3 F 1b 1 = Mandatory power management feature set is supported 2 X 0b Obsolete 1 F 1b 1 = Security feature set is supported 0 F 1b 1 = SMART feature set is supported CCMTD-731836775-10503 5200_series_ssd.pdf - Rev. E 05/18 EN 15 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2017 Micron Technology, Inc. All rights reserved. 5200 Series NAND Flash SSD Device ID Table 11: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting 83 84 Default Value Description - - - Command and feature sets are supported 15 F 0b Shall be cleared to zero 14 F 1b Shall be set to one 13 F 1b 1 = FLUSH CACHE EXT command is supported 12 F 1b 1 = Mandatory FLUSH CACHE command is supported 11 X 0b Obsolete 1 = 48-bit address feature set is supported 10 F 1b 9-7 X 000b 6 F 0b 1 = SET FEATURES subcommand required to spin-up after power-up 5 F 0b 1 = Power-up in standby feature set is supported 4 X 0b Obsolete 3 F 1b 1 = Advanced power management feature set is supported 2 F 0b Reserved for CFA 1 X 0b Obsolete 0 F 1b 1 = DOWNLOAD MICROCODE command is supported - - - 15 F 0b Shall be cleared to zero 14 F 1b Shall be set to one 13 F 1b 1 = Idle immediate with unload feature is supported 12 F 0b Reserved for technical report INCITS TR-37-2004 (TLC) 11 F 0b Reserved for technical report INCITS TR-37-2004 (TLC) 10-9 X 00b Obsolete 8 F 1b 1 = 64-bit word wide name is supported 7 X 0b Obsolete 6 F 1b 1 = WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT commands are supported 5 F 1b 1 = General purpose logging feature set is supported 4 F 0b 1 = Streaming feature set is supported 3 X 0b Obsolete 2 - 0b Reserved 1 F 1b 1 = SMART self-test is supported 0 F 1b 1 = SMART error logging is supported CCMTD-731836775-10503 5200_series_ssd.pdf - Rev. E 05/18 EN Obsolete Command and feature sets are supported 16 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2017 Micron Technology, Inc. All rights reserved. 5200 Series NAND Flash SSD Device ID Table 11: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting 85 86 Default Value Description - - - Command and feature sets are supported or enabled 15 X 0b Obsolete 14 F 1b 1 = NOP command is supported 13 F 1b 1 = READ BUFFER command is supported 12 F 1b 1 = WRITE BUFFER command is supported 11-10 X 00b Obsolete 9 F 0b 1 = DEVICE RESET command is supported 8-7 X 00b Obsolete 6 V 1b 1 = Read look-ahead is enabled 5 V 1b 1 = Write cache is enabled 4 F 0b Shall be cleared to zero to indicate that the packet feature set is not supported 3 F 1b Mandatory power management feature set is supported 2 X 0b Obsolete 1 V 0b 1 = Security feature set is enabled 0 V 1b 1 = SMART feature set is enabled - - - 15 - 1b 1 = Words 120-119 are valid 14 X 0b Reserved 13 F 1b 1 = FLUSH CACHE EXT command is supported 12 F 1b 1 = FLUSH CACHE command is supported 11 X 0b Obsolete 10 F 1b 1 = 48-bit address feature set is supported 9-7 X 000b 6 F 0b 1 = SET FEATURES subcommand required to spin-up after power-up 5 V 0b 1 = Power-up in standby feature set is enabled 4 X 0b Obsolete 3 V 1b 1 = Advanced power management feature set is enabled 2 X 0b Reserved for CFA 1 X 0b Obsolete 0 F 1b 1 = DOWNLOAD MICROCODE command is supported CCMTD-731836775-10503 5200_series_ssd.pdf - Rev. E 05/18 EN Command and feature sets are supported or enabled Obsolete 17 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2017 Micron Technology, Inc. All rights reserved. 5200 Series NAND Flash SSD Device ID Table 11: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting 87 88 89 Default Value Description - - - Command and feature sets are supported or enabled 15 F 0b Shall be cleared to zero 14 F 1b Shall be set to one 13 F 1b 1 = IDLE IMMEDIATE with UNLOAD FEATURE is supported 12-9 X 0000b 8 F 1b 1 = 64-bit word wide name is supported 7 X 0b Obsolete 6 F 1b 1 = WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT commands are supported 5 F 1b 1 = General purpose logging feature set is supported 4-3 X 00b Obsolete 2 V 0b 1 = Media serial number is valid 1 F 1b 1 = SMART self-test is supported 0 F 1b 1 = SMART error logging is supported - - 0b Ultra DMA modes Obsolete 15 - 0b Reserved 14 V 0b 1 = Ultra DMA mode 6 is selected 0 = Ultra DMA mode 6 is not selected 13 V 0b 1 = Ultra DMA mode 5 is selected 0 = Ultra DMA mode 5 is not selected 12 V 0b 1 = Ultra DMA mode 4 is selected 0 = Ultra DMA mode 4 is not selected 11 V 0b 1 = Ultra DMA mode 3 is selected 0 = Ultra DMA mode 3 is not selected 10 V 0b 1 = Ultra DMA mode 2 is selected 0 = Ultra DMA mode 2 is not selected 9 V 0b 1 = Ultra DMA mode 1 is selected 0 = Ultra DMA mode 1 is not selected 8 V 0b 1 = Ultra DMA mode 0 is selected 0 = Ultra DMA mode 0 is not selected 7 - 0b Reserved 6 V 1b 1 = Ultra DMA mode 6 and below are supported 5 V 1b 1 = Ultra DMA mode 5 and below are supported 4 V 1b 1 = Ultra DMA mode 4 and below are supported 3 V 1b 1 = Ultra DMA mode 3 and below are supported 2 V 1b 1 = Ultra DMA mode 2 and below are supported 1 V 1b 1 = Ultra DMA mode 1 and below are supported 0 V 1b 1 = Ultra DMA mode 0 is supported - F 0002h CCMTD-731836775-10503 5200_series_ssd.pdf - Rev. E 05/18 EN Time required for security erase unit completion 18 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2017 Micron Technology, Inc. All rights reserved. 5200 Series NAND Flash SSD Device ID Table 11: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting Default Value Description 90 - F 0002h Time required for enhanced security erase completion 91 - V 00FEh Current advanced power management value 92 - V FFFEh Master password revision code 93 - - 0000h Hardware reset results; set to 0000h for SATA devices 94 - X 0000h Obsolete 95 - F 0000h Stream minimum request size 96 - V 0000h Streaming transfer time - DMA 97 - V 0000h Streaming access latency - DMA and PIO 98-99 - F 0000h 0000h 100-103 - V Varies by capacity 104 - V 0000h Streaming transfer time - PIO 105 - F 0008h Maximum number of 512-byte blocks of LBA range entries per DATA SET MANAGEMENT command 106 - - - 15 F 0b Shall be cleared to zero 14 F 1b Shall be set to one 13 F 1b 1 = Device has multiple logical sectors per physical sector 12 F 0b 1 = Device logical sector longer than 256 Words 11-4 F 00000000b Streaming performance granularity (98-99) Maximum user LBA for 48-bit address feature set Physical sector size/logical sector size Reserved 3-0 F Varies Logical sectors per physical sector 107 - F 0000h Inter-seek delay for ISO-7779 acoustic testing in microseconds 108 15-12 F 0101b NAA (3-0) 11-0 - 000000001010b 15-4 F 000001110101b 3-0 - Varies Unique ID (35-32) 110 - F Varies 5-0 unique ID (31-16) 111 - F Varies Unique ID (15-0) 112-115 - F 116 - X 0000h 117-118 - F 0000h 0000h 109 CCMTD-731836775-10503 5200_series_ssd.pdf - Rev. E 05/18 EN IEEE OUI (23-12) IEEE OUI (11-0) 0000h 0000h 0000h Reserved for 128-bit world wide name extension to 128 bits 0000h Obsolete Words per logical sector 19 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2017 Micron Technology, Inc. All rights reserved. 5200 Series NAND Flash SSD Device ID Table 11: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting 119 Default Value Description - - - Command and feature sets are supported (continued from words 84-82) 15 F 0b Shall be cleared to zero Shall be set to one 14 F 1b 13-10 F 0000b 9 F 0b 1 = DSN feature set is supported 8 F 1b 1 = Accessible maximum address configuration feature set is supported 7 F 0b 1 = Extended power conditions feature set is supported 6 F 0b 1 = Sense data reporting feature set is supported 5 F 0b 1 = Free-fall control feature set is supported 4 F 1b 1 = DOWNLOAD MICROCODE command with mode 3 supported 3 F 1b 1 = READ LOG DMA EXT and WRITE LOG DMA EXT commands supported 2 F 1b 1 = Write uncorrectable EXT command is supported 1 F 1b 1 = Write-read-verify feature set is supported 0 X 0b Obsolete - - - 15 - 0b Shall be cleared to zero 14 - 1b Shall be set to one 13-10 - 0000b 9 - 0b DSN feature set is enabled 8 - 0b Reserved 7 - 0b 1 = Extended power conditions feature set is enabled 6 - 0b 1 = Sense data reporting feature set is enabled 5 - 0b 1 = Free-fall control feature set is enabled 4 F 1b 1 = The DOWNLOAD MICROCODE command with mode 3 is supported 3 F 1b 1 = The READ LOG DMA EXT and WRITE LOG DMA EXT commands are supported 2 F 1b 1 = The WRITE UNCORRECTABLE EXT command is supported 1 V 0b 1 = The write-read-verify feature set is enabled 0 X 0b Obsolete 121-126 - F 127 - X 120 CCMTD-731836775-10503 5200_series_ssd.pdf - Rev. E 05/18 EN Reserved Commands and feature sets are supported or enabled (continued from words 87-85) Reserved 0000h 0000h 0000h Reserved for expanded supported and enabled settings 0000h 0000h 0000h 0000h Obsolete 20 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2017 Micron Technology, Inc. All rights reserved. 5200 Series NAND Flash SSD Device ID Table 11: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting 128 Default Value - - - 15-9 F 0000000b Description Security status Reserved 8 V 0b Master password capability: 0 = High, 1 = Maximum 7-6 F 00b Reserved 5 F 1b 1 = Enhanced security erase is supported 4 V 0b 1 = Security count is expired 3 V 0b 1 = Security is frozen 2 V 0b 1 = Security is locked 1 V 0b 1 = Security is enabled 0 F 1b 1 = Security is supported 129-159 - X Vendor-specific data Vendor specific 160-167 - - 0000h 0000h 0000h Reserved for the CompactFlash Association 0000h 0000h 0000h 0000h 0000h 168 15-4 F 000h Reserved 3-0 F Varies Device nominal form factor; 3h = 2.5", 7h = M.2 169 - - 15-1 F 0 F 170-173 - F 174-175 - F 0000h 0000h 176-205 - V Varies 206 - - - 15-12 X 0000b 11-6 F 000000b 5 F 1b 1 = The SCT Data Tables command is supported 4 F 1b 1 = The SCT Feature Control command is supported 3 F 0b 1 = The SCT Error Recovery Control command is supported 2 F 1b 1 = The SCT Write Same command is supported 1 X 0b Obsolete 0 F 1b 1 = The SCT Command Transport is supported - - 0000h 0000h 207-208 CCMTD-731836775-10503 5200_series_ssd.pdf - Rev. E 05/18 EN - DATA SET MANAGEMENT command support 000000000000000b Reserved 1b 1 = The trim bit in the DATA SET MANAGEMENT command is supported 0000h 0000h 0000h Additional product identifier 0000h Reserved Current media serial number (60 ASCII characters) SCT command transport Vendor-specific Reserved Reserved 21 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2017 Micron Technology, Inc. All rights reserved. 5200 Series NAND Flash SSD Device ID Table 11: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting 209 Default Value Description - - - Alignment of logical blocks within a larger physical block 15 F 0b Shall be cleared to zero Shall be set to one 14 F 1b 13-0 F 00000000000000b 210-211 - V 0000h 0000h Write-read-verify sector count mode 3 212-213 - F 0000h 0001h Write-read-verify sector count mode 2 214-216 - X 217 - F 0001h Nominal media rotation rate (non-rotating media) 218 - - 0000h Reserved 219 - X 0000h Obsolete 220 15-8 F 00h Reserved 7-0 V 00h Write-read-verify feature set current mode 221 - - 0000h 222 - - - Transport major revision number. 0000h or FFFFh = Device does not report version 15-12 F 0001b Transport type: 0h = Parallel, 1h = Serial, Eh = PCIe, All others = Reserved 11-8 - 0000b Reserved 7 F 1b 1 = SATA rev 3.2 is supported 6 F 1b 1 = SATA rev 3.1 is supported 5 F 1b 1 = SATA rev 3.0 is supported 4 F 1b 1 = SATA rev 2.6 is supported 3 F 1b 1 = SATA rev 2.5 is supported 2 F 1b 1 = SATA II: Extensions are supported 1 F 1b 1 = SATA rev 1.0a is supported 0 F 1b 1 = ATA8-AST is supported 223 - F 0000h 224-229 - F 0000h 0000h 0000h Reserved 0000h 0000h 0000h 230-233 - - 0000h 0000h 0000h Extended number of user-addressable sectors 0000h 234 - F 0001h Minimum number of 512-byte units per DOWNLOAD MICROCODE command for mode 3 235 - F 0FFFh Maximum number of 512-byte units per DOWNLOAD MICROCODE command for mode 3 236-242 - - CCMTD-731836775-10503 5200_series_ssd.pdf - Rev. E 05/18 EN Logical sector offset within the first physical sector where the first logical sector is placed 0000h 0000h 0000h Obsolete Reserved Transport minor revision number 0000h 0000h 0000h Reserved 0000h 0000h 0000h 0000h 22 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2017 Micron Technology, Inc. All rights reserved. 5200 Series NAND Flash SSD Device ID Table 11: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting 243 Default Value 15 - 0b 14 F 0b/1b 13-0 - 00000000000000b 244-254 - - 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 255 - F - 15-8 - Varies 7-0 - A5h Note: CCMTD-731836775-10503 5200_series_ssd.pdf - Rev. E 05/18 EN Description Reserved 1 = FDE security features supported This bit will be 1 for TCG drives, otherwise 0. Reserved Integrity word Checksum Checksum validity indicator 1. F = The content of the word is fixed and does not change. V = The content of the word is variable and may change depending on the state of the device or the commands executed by the device. X = The content of the word may be fixed or variable. 23 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2017 Micron Technology, Inc. All rights reserved. 5200 Series NAND Flash SSD Commands Commands Table 12: Supported ATA Command Set See ATA-8 standard for command details Command Name Command Code (hex) AMAC-GET NATIVE MAX ADDRESS EXT 78h/0000h AMAC-SET ACCESSIBLE MAX ADDRESS EXT 78h/0001h AMAC-FREEZE ACCESSIBLE MAX ADDRESS EXT 78h/0002h CHECK POWER MODE E5h DATA SET MANAGEMENT - TRIM 06h/0001h DOWNLOAD MICROCODE 92h DOWNLOAD MICROCODE DMA 93h EXECUTE DEVICE DIAGNOSTIC 90h FLUSH CACHE E7h FLUSH CACHE EXT EAh IDENTIFY DEVICE ECh IDLE E3h IDLE IMMEDIATE E1h INITIALIZE DEVICE PARAMETERS 91h NOP 00h READ BUFFER E4h READ BUFFER DMA E9h READ DMA (with retry) C8h READ DMA EXT 25h READ FPDMA QUEUED 60h READ LOG DMA EXT 47h READ LOG EXT 2Fh READ MULTIPLE C4h READ MULTIPLE EXT 29h READ SECTOR(S) EXT 24h READ SECTOR(S) (with retry) 20h READ VERIFY SECTOR EXT 42h READ VERIFY SECTOR(S) (with retry) 40h SANITIZE DEVICE B4h SECURITY DISABLE PASSWORD F6h SECURITY ERASE PREPARE F3h SECURITY ERASE UNIT F4h SECURITY FREEZE LOCK F5h SECURITY SET PASSWORD F1h SECURITY UNLOCK F2h SET FEATURES EFh CCMTD-731836775-10503 5200_series_ssd.pdf - Rev. E 05/18 EN 24 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2017 Micron Technology, Inc. All rights reserved. 5200 Series NAND Flash SSD Commands Table 12: Supported ATA Command Set (Continued) See ATA-8 standard for command details Command Name Command Code (hex) SET MULTIPLE MODE C6h SLEEP E6h SMART DISABLE OPERATIONS B0h/D9h SMART ENABLE OPERATIONS B0h/D8h SMART ENABLE/DISABLE AUTOSAVE B0h/D2h SMART EXECUTE OFF-LINE IMMEDIATE B0h/D4h SMART READ DATA B0h/D0h SMART READ DATA ATTRIBUTE THRESHOLDS B0h/D1h SMART READ LOG B0h/D5h SMART RETURN STATUS B0h/DAh SMART SAVE ATTRIBUTE VALUES B0h/D3h SMART WRITE LOG B0h/D6h STANDBY E2h STANDBY IMMEDIATE E0h WRITE BUFFER E8h WRITE BUFFER DMA EBh WRITE DMA (with retry) CAh WRITE DMA EXT 35h WRITE DMA FUA EXT 3Dh WRITE FPDMA QUEUED 61h WRITE LOG EXT 3Fh WRITE LOG DMA EXT 57h WRITE MULTIPLE C5h WRITE MULTIPLE EXT 39h WRITE MULTIPLE FUA EXT CEh WRITE SECTOR(S) (with retry) 30h WRITE SECTOR(S) EXT 34h WRITE UNCORRECTABLE EXT 45h Table 13: Additional Command Set for TCG Drives Command Name Command Code (hex) TRUSTED NON-DATA 5Bh TRUSTED RECEIVE 5Ch TRUSTED RECEIVE DMA 5Dh TRUSTED SEND 5Eh TRUSTED SEND DMA 5Fh CCMTD-731836775-10503 5200_series_ssd.pdf - Rev. E 05/18 EN 25 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2017 Micron Technology, Inc. All rights reserved. 5200 Series NAND Flash SSD Interface Connectors Interface Connectors 2.5-Inch 7mm Figure 3: 2.5-Inch 7mm SATA Interface Connections P1 S1 Signal segment Power segment Table 14: Signal Segment Pin Assignments - 2.5-Inch SATA Signal Name Type Description S1 GND Ground S2 A+ S3 A- S4 GND S5 B- S6 B+ S7 GND Differential signal pair A Ground Differential signal pair B Ground Table 15: Power Segment Pin Assignments - 2.5-Inch SATA Power Name Type P1 Retired No connect P2 Retired No connect P3 PWDIS Enter/Exit Power Disable P4 GND Ground P5 GND Ground P6 GND Ground P7 V5 5V power, precharge P8 V5 5V power P9 V5 5V power P10 GND Ground P11 DAS Device activity signal P12 GND Ground P13 V12 12V power P14 V12 12V power P15 V12 12V power CCMTD-731836775-10503 5200_series_ssd.pdf - Rev. E 05/18 EN Description 26 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2017 Micron Technology, Inc. All rights reserved. 5200 Series NAND Flash SSD Physical Configuration Physical Configuration 2.5-Inch 7mm Product mass: less than 70 grams Screw: M3 x 0.5 with a maximum of 5mm encroachment into the SSD Torque: Maximum of 4 in-lbs @ 200 rpm with an actuation style lever Figure 4: 2.5-Inch Package - 7mm (4.80) (3.50) (2X M3) (Both sides) H +0.20/-0.50 (3.00) (14.00) W 0.25 (90.60) L MAX (4.07) (4X M3) (61.71) (14.00) (90.60) Note: 1. All dimensions are in millimeters. Table 16: 2.5-Inch Package Dimensions Capacity (GB) W L H Unit 240 69.85 100.45 7.00 mm 480 960 1920 3840 7680 Note: CCMTD-731836775-10503 5200_series_ssd.pdf - Rev. E 05/18 EN 1. Dimension values in millimeter per SFF 8201 Rev. 3.3. 27 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2017 Micron Technology, Inc. All rights reserved. 5200 Series NAND Flash SSD Compliance Compliance Micron SSDs comply with the following: * * * * * Micron Green Standard Built with sulfur resistant resistors CE (Europe): EN 55032 Class B, RoHS FCC: CFR Title 47, Part 15 Class B UL/cUL: approval to UL-60950-1, 2nd Edition, IEC 60950-1:2005 (2nd Edition); EN 60950-1 (2006) + A11:2009+ A1:2010 + A12:2011 + A2:2013 * BSMI (Taiwan): approval to CNS 13438 Class B and CNS 15663 * RCM (Australia, New Zealand): AS/NZS CISPR32 Class B * KC RRA (Korea): approval to KN32 Class B, KN 35 Class B * W.E.E.E.: compliance with EU WEEE directive 2012/19/EC. Additional obligations may apply to customers who place these products in the markets where WEEE is enforced. * TUV (Germany): approval to IEC60950/EN60950 * VCCI (Japan): 2015-04 Class B * IC (Canada): ICES-003 Class B - This Class B digital apparatus complies with Canadian ICES-003. - Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada. * Morocco: approval to EN55032/EN55024 Class B FCC Rules This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: * Reorient or relocate the receiving antenna. * Increase the separation between the equipment and the receiver. * Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. * Consult the dealer or an experienced radio/TV technician for help. CCMTD-731836775-10503 5200_series_ssd.pdf - Rev. E 05/18 EN 28 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2017 Micron Technology, Inc. All rights reserved. 5200 Series NAND Flash SSD References References * Serial ATA: High-speed serialized AT attachment, Serial ATA working group, available at www.sata-io.org * SATA 3.3 GOLD * ATA-8 ACS-3 Revision 5 * SFF-8201 Rev. 3.3: For 2.5-Inch mechanical * Trusted Computing Group (TCG) Enterprise Specification Version 1.00 Revision Final, Revision 3.00 January 10, 2011. Available at www.trustedcomputinggroup.org * Trade Agreements Act of 1979 (19 U.S.C. 2501) CCMTD-731836775-10503 5200_series_ssd.pdf - Rev. E 05/18 EN 29 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2017 Micron Technology, Inc. All rights reserved. 5200 Series NAND Flash SSD Revision History Revision History Rev. E - 05/18 * Added 240GB MAX and 3840GB PRO configurations * Updated Performance Table 3 * Updated Power Consumption Table 8 Rev. D - 04/18 * Added MAX configurations * Added assembly recommendations * Re-certified from Class A to Class B Rev. C - 01/18 * Updated Shock Vibration table specifications * Corrected 480GB ECO TBW rating in Drive Lifetime table * Corrected Identify Device Word 235 value in Device ID Rev. B - 12/17 * Removed the 480GB PRO option * Updated Power Consumption specifications * Updated Performance specifications Rev. A - 10/17 * Initial release 8000 S. Federal Way, P.O. Box 6, Boise, ID 83707-0006, Tel: 208-368-4000 www.micron.com/products/support Sales inquiries: 800-932-4992 Micron and the Micron logo are trademarks of Micron Technology, Inc. All other trademarks are the property of their respective owners. This data sheet contains minimum and maximum limits specified over the power supply and temperature range set forth herein. Although considered final, these specifications are subject to change, as further product development and data characterization sometimes occur. CCMTD-731836775-10503 5200_series_ssd.pdf - Rev. E 05/18 EN 30 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2017 Micron Technology, Inc. All rights reserved.