SN5414, SN54LS14, SN7414, SN74LS14 HEX SCHMITT-TRIGGER INVERTERS SDLS049B - DECEMBER 1983 - REVISED FEBRUARY 2002 D D D SN5414, SN54LS14 . . . J OR W PACKAGE SN7414 . . . D, N, OR NS PACKAGE SN74LS14 . . . D, DB, OR N PACKAGE (TOP VIEW) Operation From Very Slow Edges Improved Line-Receiving Characteristics High Noise Immunity 1A 1Y 2A 2Y 3A 3Y GND description Each circuit functions as an inverter, but because of the Schmitt action, it has different input threshold levels for positive-going (VT+) and negative-going (VT-) signals. These circuits are temperature compensated and can be triggered from the slowest of input ramps and still give clean, jitter-free output signals. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 VCC 6A 6Y 5A 5Y 4A 4Y 1Y 1A NC VCC 6A SN54LS14 . . . FK PACKAGE (TOP VIEW) 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 6Y NC 5A NC 5Y 3Y GND NC 4Y 4A 2A NC 2Y NC 3A NC - No internal connection ORDERING INFORMATION PACKAGE TA TOP-SIDE MARKING Tube SN7414N SN7414N Tube SN74LS14N SN74LS14N Tube SN7414D Tape and reel SN7414DR Tube SN74LS14D Tape and reel SN74LS14DR SOP - NS Tape and reel SN7414NSR SN7414 SSOP - DB Tape and reel SN74LS14DBR LS14 Tube SN5414J SN5414J Tube SNJ5414J SNJ5414J Tube SN54LS14J SN54LS14J Tube SNJ54LS14J SNJ54LS14J Tube SNJ5414W SNJ5414W Tube SNJ54LS14W SNJ54LS14W Tube SNJ54LS14FK PDIP - N 0C to 70C ORDERABLE PART NUMBER SOIC - D CDIP - J -55C to 125C CFP - W LCCC - FK 7414 LS14 SNJ54LS14FK Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 2002, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. On products compliant to MIL-PRF-38535, all parameters are tested unless otherwise noted. On all other products, production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 SN5414, SN54LS14, SN7414, SN74LS14 HEX SCHMITT-TRIGGER INVERTERS SDLS049B - DECEMBER 1983 - REVISED FEBRUARY 2002 logic diagram (positive logic) 1A 1 2 1Y 2A 3 4 2Y 3A 5 6 3Y 4A 9 8 4Y 5A 11 10 5Y 6A 13 12 6Y Y=A Pin numbers shown are for the D, DB, J, N, NS, and W packages. 2 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN5414, SN54LS14, SN7414, SN74LS14 HEX SCHMITT-TRIGGER INVERTERS SDLS049B - DECEMBER 1983 - REVISED FEBRUARY 2002 schematic '14 VCC 100 6 k Output Y Input A GND 'LS14 VCC 20 k Output Y Input A GND Resistor values shown are nominal. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 3 SN5414, SN54LS14, SN7414, SN74LS14 HEX SCHMITT-TRIGGER INVERTERS SDLS049B - DECEMBER 1983 - REVISED FEBRUARY 2002 absolute maximum ratings over operating free-air temperature (unless otherwise noted) Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Input voltage: '14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V 'LS14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Package thermal impedance, JA (see Note 2): D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86C/W DB package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96C/W N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80C/W NS package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76C/W Storage temperaturerange, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65C to 150C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. Voltage values are with respect to network ground terminal. 2. The package termal impedance is calculated in accordance with JESD 51-7 recommended operating conditions SN5414 VCC IOH Supply voltage IOL TA Low-level output current MIN NOM 4.5 5 High-level output current SN7414 MIN NOM MAX 5.5 4.75 5 5.25 V -0.8 mA 16 mA 70 C -0.8 16 Operating free-air temperature -55 UNIT MAX 125 0 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) SN5414 SN7414 TEST CONDITIONS PARAMETER MIN TYP UNIT MAX VT+ VT- VCC = 5 V VCC = 5 V 1.5 1.7 2 V 0.6 0.9 1.1 V Hysteresis (VT+ - VT-) VCC = 5 V 0.4 0.8 VIK VOH VCC = MIN, VCC = MIN, II = -12 mA VI = 0.6 V, VOL IT+ VCC = MIN, VCC = 5 V, VI = 2 V, VI = VT+ IT- II VCC = 5 V, VCC = MAX, VI = VT- VI = 5.5 V IIH IIL VCC = MAX, VCC = MAX, VIH = 2.4 V VIL = 0.4 V IOS ICCH VCC = MAX V -1.5 IOH = -0.8 mA IOL = 16 mA 2.4 3.4 0.2 V 0.4 -0.43 mA 1 mA 40 A -1.2 mA -55 mA 22 36 mA ICCL 39 For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions. All typical values are at VCC = 5 V, TA = 25C. Not more than one output should be shorted at a time. 60 mA 4 -18 V mA -0.56 -0.8 V VCC = MAX VCC = MAX POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN5414, SN54LS14, SN7414, SN74LS14 HEX SCHMITT-TRIGGER INVERTERS SDLS049B - DECEMBER 1983 - REVISED FEBRUARY 2002 switching characteristics, VCC = 5 V, TA = 25C (see Figure 1) PARAMETER FROM (INPUT) TO (OUTPUT) A Y tPLH SN5414 SN7414 TEST CONDITIONS MIN RL = 400 , tPHL UNIT TYP MAX 15 22 15 22 CL = 15 pF F ns recommended operating conditions SN54LS14 SN74LS14 UNIT MIN NOM MAX MIN NOM MAX 4.5 5 5.5 4.75 5 5.25 V VCC IOH Supply voltage High-level output current -0.4 -0.4 mA IOL TA Low-level output current 4 8 mA 70 C Operating free-air temperature -55 125 0 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) SN54LS14 MIN TYP MAX TEST CONDITIONS PARAMETER SN74LS14 MIN TYP MAX UNIT VT+ VT- VCC = 5 V VCC = 5 V 1.4 1.6 1.9 1.4 1.6 1.9 V 0.5 0.8 1 0.5 0.8 1 V Hysteresis (VT+ - VT-) VCC = 5 V 0.4 0.8 0.4 0.8 VIK VOH VCC = MIN, VCC = MIN, II = -18 mA VI = 0.5 V, 2.5 3.4 2.7 3.4 VOL VCC = MIN MIN, VI = -1.9 19V IT+ IT- VCC = 5 V, VCC = 5 V, VI = VT+ VI = VT- II IIH VCC = MAX, VCC = MAX, VI = 7 V VIH = 2.7 V 0.1 20 20 A IIL IOS VCC = MAX, VCC = MAX VIL = 0.4 V -0.4 -0.4 mA -100 mA ICCH ICCL VCC = MAX VCC = MAX -1.5 IOH = -0.4 mA IOL= 4 mA 0.25 -1.5 0.4 IOL = 8 mA -0.14 0.25 0.4 0.35 0.5 mA 0.1 -20 V mA -0.18 -100 V V -0.14 -0.18 -20 V mA 8.6 16 8.6 16 mA 12 21 12 21 mA TYP MAX 15 22 15 22 For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions. All typical values are at VCC = 5 V, TA = 25C. Not more than one output should be shorted at a time, and duration of the short-circuit should not exceed one second. switching characteristics, VCC = 5 V, TA = 25C (see Figure 2) PARAMETER tPLH FROM (INPUT) TO (OUTPUT) A Y tPHL POST OFFICE BOX 655303 TEST CONDITIONS RL = 2 k k, CL = 15 pF F * DALLAS, TEXAS 75265 MIN UNIT ns 5 SN5414, SN54LS14, SN7414, SN74LS14 HEX SCHMITT-TRIGGER INVERTERS SDLS049B - DECEMBER 1983 - REVISED FEBRUARY 2002 PARAMETER MEASUREMENT INFORMATION SERIES 54/74 DEVICES VCC Test Point VCC RL From Output Under Test CL (see Note A) CL (see Note A) High-Level Pulse 1.5 V S2 LOAD CIRCUIT FOR 3-STATE OUTPUTS 3V Timing Input 1.5 V 1 k Test Point LOAD CIRCUIT FOR OPEN-COLLECTOR OUTPUTS LOAD CIRCUIT FOR 2-STATE TOTEM-POLE OUTPUTS S1 (see Note B) CL (see Note A) RL (see Note B) RL From Output Under Test VCC From Output Under Test Test Point 1.5 V 0V tw Low-Level Pulse 1.5 V tsu Data Input 1.5 V VOLTAGE WAVEFORMS PULSE DURATIONS 1.5 V 1.5 V In-Phase Output (see Note D) tPHL VOH 1.5 V Out-of-Phase Output (see Note D) 0V 1.5 V 1.5 V Waveform 1 (see Notes C and D) tPLZ VOH 1.5 V 1.5 V VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES 1.5 V 1.5 V VOL tPZH tPLH 1.5 V 0V tPZL VOL tPHL 1.5 V 3V Output Control (low-level enabling) 0V tPLH 3V 1.5 V VOLTAGE WAVEFORMS SETUP AND HOLD TIMES 3V Input th Waveform 2 (see Notes C and D) VOL + 0.5 V tPHZ VOH 1.5 V VOH - 0.5 V 1.5 V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES, 3-STATE OUTPUTS NOTES: A. CL includes probe and jig capacitance. B. All diodes are 1N3064 or equivalent. C. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. D. S1 and S2 are closed for tPLH, tPHL, tPHZ, and tPLZ; S1 is open and S2 is closed for tPZH; S1 is closed and S2 is open for tPZL. E. All input pulses are supplied by generators having the following characteristics: PRR 1 MHz, ZO 50 ; tr and tf 7 ns for Series 54/74 devices and tr and tf 2.5 ns for Series 54S/74S devices. F. The outputs are measured one at a time with one input transition per measurement. Figure 1. Load Circuits and Voltage Waveforms 6 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN5414, SN54LS14, SN7414, SN74LS14 HEX SCHMITT-TRIGGER INVERTERS SDLS049B - DECEMBER 1983 - REVISED FEBRUARY 2002 PARAMETER MEASUREMENT INFORMATION SERIES 54LS/74LS DEVICES VCC Test Point VCC RL (see Note B) From Output Under Test CL (see Note A) High-Level Pulse 1.3 V S2 LOAD CIRCUIT FOR 3-STATE OUTPUTS 3V Timing Input 1.3 V 5 k Test Point LOAD CIRCUIT FOR OPEN-COLLECTOR OUTPUTS LOAD CIRCUIT FOR 2-STATE TOTEM-POLE OUTPUTS S1 (see Note B) CL (see Note A) RL CL (see Note A) RL From Output Under Test VCC From Output Under Test Test Point 1.3 V 0V tw Low-Level Pulse 1.3 V tsu 0V In-Phase Output (see Note D) 3V 1.3 V 1.3 V 0V tPZL tPLZ tPHL VOH 1.3 V 1.3 V Waveform 1 (see Notes C and D) VOL tPZH tPLH VOH 1.3 V 1.3 V VOL Waveform 2 (see Notes C and D) VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES 1.5 V 1.3 V VOL tPHL Out-of-Phase Output (see Note D) 1.3 V 0V Output Control (low-level enabling) 1.3 V tPLH 1.3 V VOLTAGE WAVEFORMS SETUP AND HOLD TIMES 3V 1.3 V 3V Data Input 1.3 V VOLTAGE WAVEFORMS PULSE DURATIONS Input th VOL + 0.5 V tPHZ VOH 1.3 V VOH - 0.5 V 1.5 V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES, 3-STATE OUTPUTS NOTES: A. CL includes probe and jig capacitance. B. All diodes are 1N3064 or equivalent. C. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. D. S1 and S2 are closed for tPLH, tPHL, tPHZ, and tPLZ; S1 is open and S2 is closed for tPZH; S1 is closed and S2 is open for tPZL. E. Phase relationships between inputs and outputs have been chosen arbitrarily for these examples. F. All input pulses are supplied by generators having the following characteristics: PRR 1 MHz, ZO 50 , tr 1.5 ns, tf 2.6 ns. G. The outputs are measured one at a time with one input transition per measurement. Figure 2. Load Circuits and Voltage Waveforms POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 7 SN5414, SN54LS14, SN7414, SN74LS14 HEX SCHMITT-TRIGGER INVERTERS SDLS049B - DECEMBER 1983 - REVISED FEBRUARY 2002 TYPICAL CHARACTERISTICS OF '14 CIRCUITS POSITIVE-GOING THRESHOLD VOLTAGE vs FREE-AIR TEMPERATURE NEGATIVE-GOING THRESHOLD VOLTAGE vs FREE-AIR TEMPERATURE 0.90 VCC = 5 V V T- - Negative-Going Threshold Voltage - V V T+ - Positive-Going Threshold Voltage - V 1.70 1.69 1.68 1.67 1.66 1.65 1.64 1.63 1.62 1.61 1.60 VCC = 5 V 0.89 0.88 0.87 0.86 0.85 0.84 0.83 0.82 0.81 0.80 -75 -50 -25 0 25 50 75 100 125 -75 -50 -25 0 25 50 75 100 TA - Free-Air Temperature - C TA - Free-Air Temperature - C Figure 3 Figure 4 HYSTERESIS vs FREE-AIR TEMPERATURE 850 VCC = 5 V 840 V T+ - V T- - Hysteresis - mV 830 820 810 800 790 780 770 760 750 -75 -50 -25 0 25 50 75 100 125 TA - Free-Air Temperature - C Figure 5 Data for temperatures below 0C and above 70C and supply voltage below 4.75 V and above 5.25 V are applicable for SN5414 only. 8 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 125 SN5414, SN54LS14, SN7414, SN74LS14 HEX SCHMITT-TRIGGER INVERTERS SDLS049B - DECEMBER 1983 - REVISED FEBRUARY 2002 TYPICAL CHARACTERISTICS OF '14 CIRCUITS THRESHOLD VOLTAGES vs SUPPLY VOLTAGE DISTRIBUTION OF UNITS FOR HYSTERESIS 2.0 VCC = 5 V TA = 25C TA = 25C Relative Frequency of Occurence 1.8 Threshold Voltage -- V 1.6 Positive-Going Threshold Voltage, VT+ 1.4 1.2 1.0 0.8 Negative-Going Threshold Voltage, VT- 0.6 0.4 0.2 0 740 760 780 800 820 840 860 880 900 5.25 5 4.75 VT+ - VT- - Hysteresis - mV 4.5 VT+ - VT- - Hysteresis - mV Figure 6 Figure 7 OUTPUT VOLTAGE vs INPUT VOLTAGE HYSTERESIS vs SUPPLY VOLTAGE 4 2.0 VCC = 5 V TA = 25C TA = 25C 1.8 VT- VT+ 1.6 VO - Output Voltage - V V T+ - VT- - Hysteresis - V 5.5 1.4 1.2 1.0 0.8 0.6 3 2 1 0.4 0.2 0 0 4.5 5 5.25 4.75 VCC - Supply Voltage - V 5.5 0 0.4 0.8 1.2 1.6 2 VCC - Supply Voltage - V Figure 8 Figure 9 Data for temperatures below 0C and above 70C and supply voltage below 4.75 V and above 5.25 V are applicable for SN5414 only. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 9 SN5414, SN54LS14, SN7414, SN74LS14 HEX SCHMITT-TRIGGER INVERTERS SDLS049B - DECEMBER 1983 - REVISED FEBRUARY 2002 TYPICAL CHARACTERISTICS OF 'LS14 CIRCUITS POSITIVE-GOING THRESHOLD VOLTAGE vs FREE-AIR TEMPERATURE NEGATIVE-GOING THRESHOLD VOLTAGE vs FREE-AIR TEMPERATURE 0.90 VCC = 5 V 1.69 VT- - Negative-Going Threshold Voltage - V V T+ - Positive-Going Threshold Voltage - V 1.70 1.68 1.67 1.66 1.65 1.64 1.63 1.62 1.61 0.88 0.87 0.86 0.85 0.84 0.83 0.82 0.81 1.60 -75 -50 -25 0 25 50 75 100 VCC = 5 V 0.89 0.80 125 0 25 50 75 100 -25 TA - Free-Air Temperature - C -75 -50 TA - Free-Air Temperature - C 125 Figure 11 Figure 10 HYSTERESIS vs FREE-AIR TEMPERATURE DISTRIBUTION OF UNITS FOR HYSTERESIS 850 Relative Frequency of Occurence V T+ - VT- - Hysteresis - V VCC = 5 V TA = 25C VCC = 5 V 840 830 820 810 800 790 780 770 99% ARE ABOVE 735 mV 760 750 -75 -50 -25 0 25 50 75 100 125 TA - Free-Air Temperature - C 720 740 760 780 800 820 840 860 880 VT+ - VT- - Hysteresis - mV Figure 12 Figure 13 Data for temperatures below 0C and above 70C and supply voltage below 4.75 V and above 5.25 V are applicable for SN5414 only. 10 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN5414, SN54LS14, SN7414, SN74LS14 HEX SCHMITT-TRIGGER INVERTERS SDLS049B - DECEMBER 1983 - REVISED FEBRUARY 2002 TYPICAL CHARACTERISTICS OF 'LS14 CIRCUITS THRESHOLD VOLTAGES AND HYSTERESIS vs SUPPLY VOLTAGE OUTPUT VOLTAGE vs INPUT VOLTAGE 2.0 4 VCC = 5 V TA = 25C TA = 25C 1.8 VT- VT+ 3 Positive-Going Threshold Voltage, VT+ 1.4 VO - Output Voltage - V Threshold Voltage - V 1.6 1.2 Negative-Going Threshold Voltage, VT- 1.0 0.8 Hysteresis, VT+ - VT- 0.6 2 1 0.4 0.2 0 0 4.5 4.75 5 5.25 5.5 0 0.4 VCC - Supply Voltage - V 0.8 1.2 1.6 2 VI - Input Voltage - V Figure 15 Figure 14 Data for temperatures below 0C and above 70C and supply voltage below 4.75 V and above 5.25 V are applicable for SN5414 only. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 11 SN5414, SN54LS14, SN7414, SN74LS14 HEX SCHMITT-TRIGGER INVERTERS SDLS049B - DECEMBER 1983 - REVISED FEBRUARY 2002 TYPICAL APPLICATION DATA TTL System VT+ VT- Input CMOS Sine-Wave Oscillator Output TTL System Interface for Slow Input Waveforms Pulse Shaper 0.1 Hz to 10 MHz VT+ 330 VT- Input Input Output Threshold Detector Multivibrator Open-Collector Output Input Input A Output Point A Output Pulse Stretcher 12 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 VT+ PACKAGE OPTION ADDENDUM www.ti.com 28-Aug-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp ACTIVE LCCC FK 20 1 TBD Call TI Call TI 5962-9665801QCA ACTIVE CDIP J 14 1 TBD Call TI Call TI 5962-9665801QDA ACTIVE CFP W 14 1 TBD Call TI Call TI 5962-9665801VCA ACTIVE CDIP J 14 25 TBD A42 N / A for Pkg Type 5962-9665801VDA ACTIVE CFP W 14 1 TBD A42 N / A for Pkg Type JM38510/31302BCA ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type M38510/31302BCA ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type SN5414J ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type SN54LS14J ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type SN7414D ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN7414DE4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN7414DG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN7414DR ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN7414DRE4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN7414DRG4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 25 Pb-Free (RoHS) SN7414N ACTIVE PDIP N 14 SN7414N3 OBSOLETE PDIP N 14 SN7414NE4 ACTIVE PDIP N 14 25 Pb-Free (RoHS) SN7414NSR ACTIVE SO NS 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN7414NSRE4 ACTIVE SO NS 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN7414NSRG4 ACTIVE SO NS 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74LS14D ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Addendum-Page 1 CU NIPDAU N / A for Pkg Type Call TI Samples (Requires Login) 5962-9665801Q2A TBD (3) Call TI CU NIPDAU N / A for Pkg Type PACKAGE OPTION ADDENDUM www.ti.com 28-Aug-2012 Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp ACTIVE SSOP DB 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74LS14DBRE4 ACTIVE SSOP DB 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74LS14DBRG4 ACTIVE SSOP DB 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74LS14DE4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74LS14DG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74LS14DR ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74LS14DRE4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74LS14DRG4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74LS14N ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type Call TI SN74LS14N3 OBSOLETE PDIP N 14 SN74LS14NE4 ACTIVE PDIP N 14 25 Pb-Free (RoHS) SN74LS14NSR ACTIVE SO NS 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74LS14NSRE4 ACTIVE SO NS 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74LS14NSRG4 ACTIVE SO NS 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SNJ5414J ACTIVE CDIP J 14 1 TBD Call TI CU NIPDAU N / A for Pkg Type A42 N / A for Pkg Type A42 N / A for Pkg Type SNJ5414W ACTIVE CFP W 14 1 TBD SNJ54LS14FK ACTIVE LCCC FK 20 1 TBD SNJ54LS14J ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type SNJ54LS14W ACTIVE CFP W 14 1 TBD A42 N / A for Pkg Type (1) POST-PLATE N / A for Pkg Type The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. Addendum-Page 2 Samples (Requires Login) SN74LS14DBR TBD (3) PACKAGE OPTION ADDENDUM www.ti.com 28-Aug-2012 OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF SN5414, SN54LS14, SN54LS14-SP, SN7414, SN74LS14 : * Catalog: SN7414, SN74LS14, SN54LS14 * Military: SN5414, SN54LS14 * Space: SN54LS14-SP NOTE: Qualified Version Definitions: * Catalog - TI's standard catalog product * Military - QML certified for Military and Defense Applications * Space - Radiation tolerant, ceramic packaging and qualified for use in Space-based application Addendum-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device SN7414DR Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 SN7414NSR SO NS 14 2000 330.0 16.4 8.2 10.5 2.5 12.0 16.0 Q1 SN74LS14DBR SSOP DB 14 2000 330.0 16.4 8.2 6.6 2.5 12.0 16.0 Q1 SN74LS14DR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 SN74LS14NSR SO NS 14 2000 330.0 16.4 8.2 10.5 2.5 12.0 16.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN7414DR SOIC D 14 2500 367.0 367.0 38.0 SN7414NSR SO NS 14 2000 367.0 367.0 38.0 SN74LS14DBR SSOP DB 14 2000 367.0 367.0 38.0 SN74LS14DR SOIC D 14 2500 367.0 367.0 38.0 SN74LS14NSR SO NS 14 2000 367.0 367.0 38.0 Pack Materials-Page 2 MECHANICAL DATA MSSO002E - JANUARY 1995 - REVISED DECEMBER 2001 DB (R-PDSO-G**) PLASTIC SMALL-OUTLINE 28 PINS SHOWN 0,38 0,22 0,65 28 0,15 M 15 0,25 0,09 8,20 7,40 5,60 5,00 Gage Plane 1 14 0,25 A 0-8 0,95 0,55 Seating Plane 2,00 MAX 0,10 0,05 MIN PINS ** 14 16 20 24 28 30 38 A MAX 6,50 6,50 7,50 8,50 10,50 10,50 12,90 A MIN 5,90 5,90 6,90 7,90 9,90 9,90 12,30 DIM 4040065 /E 12/01 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-150 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated