DATASHEET WIDE BANDWIDTH VIDEO SIGNAL SWITCH, 5 PORT General Description Features The IDTVS512 is a bi-directional 5-Port 2:1 multiplexer/demultiplexer with Hi-Z outputs for both RGB and composite video switching applications. With the additional two ports, vertical and horizontal synchronous signals can be switched in addition to switching the RGB and composite signals between different components (DVDs, VCRs, PCs, etc.). The VideoSwitch can be driven from a current output RAMDAC or voltage output composite video source. * * * * * * * * * * Low on-resistance, low crosstalk, low OFF isolation and wide bandwidth features make it ideal for video and other applications. The IDTVS512 offers a high-performance (600 MHz), low-cost solution to switch between video sources. CONFIDENTIAL IDTVS512 RON is 4 typical Bidirectional switch Low bit-to-bit skew: 200ps Low crosstalk: -65dB @ 10MHz Near-Zero propagation delay: 250ps Fast switching speed: 9ns Channel On-Capacitance: 6pF (typical) 8KV ESD HBM on connector side Wide bandwidth (600 MHz) Available in QSOP package Applications * Projection TV and LCD TV * Video consumer applications * Analog video signal routing Block Diagram A0 YA A1 B0 YB B1 C0 YC C1 D0 YD D1 E0 YE E1 CTL WIDE BANDWIDTH VIDEO SIGNAL SWITCH, 5 PORT 1 CONFIDENTIAL IDTVS512 7013/7 IDTVS512 WIDE BANDWIDTH VIDEO SIGNAL SWITCH, 5 PORT COMMERCIAL TEMPERATURE RANGE Pin Configuration VDD 1 24 A0 YA 2 23 A1 GND 3 22 B0 VDD 4 21 B1 YB 5 20 GND YC 6 19 VDD GND 7 18 C0 YD 8 17 D0 VDD 9 16 C1 GND 10 15 D1 YE 11 14 E0 CTL 12 13 E1 QSOP TOP VIEW Absolute Maximum Ratings Min Max1 Unit Storage Temperature Range - 65 +150 C Supply Voltage to GND Potential - 0.5 +4 V DC Input Voltage - 0.5 +5.5 V DC Output Current -- 120 mA Power Dissipation -- 0.5 W Symbol TSTG Rating 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. Capacitance (TA = +25C, f = 1.0MHz) Symbol Parameter Conditions Typ Max1 Unit CIN Input Capacitance VIN = 0V 2 3 pF COFF(IN0, IN1) Port I Capacitance, Switch OFF VIN = 0V 4 6 pF CON(Y/I) Y/I Port Capacitance, Switch ON VIN = 0V 6 10 pF 1. As applicable to the device type. WIDE BANDWIDTH VIDEO SIGNAL SWITCH, 5 PORT 2 CONFIDENTIAL IDTVS512 7013/7 IDTVS512 WIDE BANDWIDTH VIDEO SIGNAL SWITCH, 5 PORT COMMERCIAL TEMPERATURE RANGE Pin Description Truth Table Name Pin # Function Function SEL VDD 1, 4, 9, 19 Positive power supply Yn to Y0 L GND 3, 7, 10, 20 Ground Yn to X1 H Xn 2, 5, 6, 8, 11, 13, 14, 15, Data and CLK 16, 17, 18, 21, 22, 23, 24 CTL 12 Control Dynamic Electrical Characteristics Over Operating Range Following Conditions Apply Unless Otherwise Specified: TA = 0C to +70C, VCC = 3.3V 10%, GND = 0V.. Symbol XTALK OIRR 1 2 BW Parameter Conditions Min. Typ. Max. Unit Crosstalk t = 10MHz -- -65 -- dB Off Isolation t = 10MHz -- -70 -- Bandwidth - 3dB CL = 0pF -- 600 -- MHz 1. See CROSSTALK SETUP for Measurement Setup. 2. See OFF-ISOLATION SETUP for Measurement Setup. DC Electrical Characteristics Over Operating Range Following Conditions Apply Unless Otherwise Specified: TA = 0C to +70C, VCC = 3.3V 10%. Symbol Conditions1 Parameter Min. Typ.2 Max. Unit VIH3 Input HIGH Voltage Guaranteed Logic HIGH level 2 -- -- VIL Input LOW Voltage Guaranteed Logic LOW level -0.5 -- 0.8 VIK Clamp Diode Voltage VCC = Max., IIN = -18mA -- -0.7 -1.2 IIH Input HIGH Current VCC = Max., VIN = VCC -- -- 5 IIL Input LOW Current VCC = Max., VIN = GND -- -- 5 IOFF Power Down Leakage Current VCC = 0V, VA = 0V, VB 3.6 -- -- -- RON4 Switch On-Resistance VCC = Min., 1.5 VIN VCC, IIN = -40mA -- 4 8 VCC = Min., VIN @ 1.5V and VCC, IIN = -40mA -- 1 -- VCC = Min., 1.5 VIN VCC, IIN = -40mA -- 0.9 2 RFLAT(ON) On-Resistance Flatness RON On-Resistance match from center ports to any other port V A 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 3.3V,TA = 25C ambient and maximum loading. 3. Measured by the voltage drop between Y and I pins at indicated current through the switch. On-Resistance is determined by the lower of the voltages on the two (Y &I) pins. 4. This parameter is determined by device characterization but is not production tested. WIDE BANDWIDTH VIDEO SIGNAL SWITCH, 5 PORT 3 CONFIDENTIAL IDTVS512 7013/7 IDTVS512 WIDE BANDWIDTH VIDEO SIGNAL SWITCH, 5 PORT COMMERCIAL TEMPERATURE RANGE Power Supply Characteristics Symbol ICC Conditions1 Parameter Quiescent Power Supply Current Min. Typ.2 Max. VCC = Max., VIN = GND or VCC -- -- 800 Unit A 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device. 2. Typical values are at VCC = 3.3V, tA = 25C ambient and maximum loading. Switching Characteristics Over Operating Range Following Conditions Apply Unless Otherwise Specified: TA = 0C to +70C, VCC = 3.3V 10%, GND = 0V. Min. Typ.1 Max. Unit tPD Propagation Delay2,3 -- 0.25 -- ns tPZH, tPZL Line Enable Time - SEL to Yn, In 0.5 -- 15 ns tPHZ, tPLZ Line Disable Time - SEL to Yn, In 0.5 -- 9 ns tSK(O) Output Skew between center port (YC to YD) to any other port(2) -- 0.1 0.2 ns tSK(P) Skew between opposite transitions of the same output (tPHL- tPLH)(2) -- 0.1 0.2 ns Symbol Description 1. For max. or min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Guaranteed by design., 3. The bus switch contributes no propagational delay other than the RC delay of the On-Resistance of the switch and the load capacitance. The time constant for the switch alone is of the order of 0.25ns for 10pF load. Since this time constant is much smaller than the rise/fall times of typical driving signals, it adds very little propagational delay to the system. Propagational delay of the bus switch when used in a system is determined by the driving circuit on the driving side of the switch and its interactions with the load on the driven side. Switching Waveforms VDD CTL 3.5V 2.5V Input Output Input A tPHL 2.5V 1.25V tPZL 2.5V tPLH 1.25V 1.5V VOH 0V VDD tPHZ VOL+0.3V VOL VOH VOH-0.3V VDD/2 tPZH 2.5V VOL VDD/2 Output A Output A Voltage Waveforms Propagation Delay Times 1.5V VOH tPHZ tPZH WIDE BANDWIDTH VIDEO SIGNAL SWITCH, 5 PORT tPLZ VDD/2 VDD/2 VOL Voltage Waveforms Enable and Disable Times 4 CONFIDENTIAL IDTVS512 7013/7 IDTVS512 WIDE BANDWIDTH VIDEO SIGNAL SWITCH, 5 PORT COMMERCIAL TEMPERATURE RANGE Data In at Ax or Ay tPHLx tPLHx Data Out at MBx tSK(0) Data Out at MBy tPLHy tPHLy 3.5V 2.5V 1.5V VOH 2.5V VOL VOH 2.5V VOL Input tPHL tPLH Output tSK(P) = | tPHL - tPHL 3.5V 2.5V 1.5V VOH 2.5V VOL | tSK(0) = | tPLHy - tPLHx | or | tPHLy - tPHLx | Output Skew - tSK(O) Pulse Skew - tSK(P) Applications Information Logic Inputs The logic control inputs can be driven up to +3.6V regardless of the supply voltage. For example, given a +3.3V supply, the output enables or select pins may be driven low to 0V and high to 3.6V. Driving IN Rail-to-RailAE minimizes power consumption. Power-supply Sequencing Proper power-supply sequencing is advised for all CMOS devices. It is recommended to always apply VCC before applying signals to the input/output or control pins. 700 3dB Bandwidth 600 500 400 300 200 100 0 0 10 20 30 40 50 Capacitance Load Bandwidth vs. Capacitance WIDE BANDWIDTH VIDEO SIGNAL SWITCH, 5 PORT 5 CONFIDENTIAL IDTVS512 7013/7 IDTVS512 WIDE BANDWIDTH VIDEO SIGNAL SWITCH, 5 PORT COMMERCIAL TEMPERATURE RANGE Test Circuit For Electrical Characteristics 6V VCC Switch Position 200 Pulse Generator Test VOUT VIN D.U.T. RT 10pF 200 CL Switch tPZH, tPZL (output on I-side) 6V tPHZ, tPLZ (output on I-side) GND Prop Delay Open 1 CL = Load capacitance: includes jig and probe capacitance. 2 RT = Termination resistance: should be equal to ZOUT of the Pulse Generator. 3 Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. 4 All input impulses are supplied by generators having the following characteristics: PRR MHz, Zo = 50, tR 2.5ns, tF 2.5ns. 5 The outputs are measured one at a time with one transition per measurement. Test Circuit for Dynamic Electrical Characteristics HP4396B S1 R1 T1 HP11667A Vcc IDTVS521 CL WIDE BANDWIDTH VIDEO SIGNAL SWITCH, 5 PORT 6 CONFIDENTIAL IDTVS512 7013/7 IDTVS512 WIDE BANDWIDTH VIDEO SIGNAL SWITCH, 5 PORT COMMERCIAL TEMPERATURE RANGE Package Dimensions - QAOP N C L E1 E INDEX AREA 1 2 D ZD A2 A A1 e -CSEATING PLANE b .10 (.004) C 150 mil SSOP (QSOP)) Symbol In Millimeters Common Dimensions In Inches Common Dimensions1 MIN MAX MIN MAX A 1.35 1.75 .053 .069 A1 0.10 0.25 .004 .010 A2 -- 1.50 -- .059 b 0.20 0.30 .008 .012 c 0.18 0.25 007 .010 D 8.55 8.75 .337 .344 E 5.80 6.20 .228 .244 E1 3.80 4.00 .150 .157 e L .635 BASIC 0.40 N 0.025 BASIC 1.27 .016 24 0 ZD .050 24 8 0 0.84 REF 8 .394 REF 1. For reference only. Controlling dimensions are in inches. WIDE BANDWIDTH VIDEO SIGNAL SWITCH, 5 PORT 7 CONFIDENTIAL IDTVS512 7013/7 IDTVS512 WIDE BANDWIDTH VIDEO SIGNAL SWITCH, 5 PORT COMMERCIAL TEMPERATURE RANGE Ordering Information IDTVS XXXX Device Type XX Package X X Temp. Range Shipping Carrier CORPORATE HEADQUARTERS 6024 Silver Creek Valley Road San Jose, CA 95138 T Blank Tape and Reel Tray Blank Commercial (0C to +70C) QG QSOP (Quarter Size Outline Package) - Green 512 wide Bandwidth Video Signal Switch for SALES: 800-345-7015 or 408-284-8200 fax: 408-284-2775 www.idt.com for Tech Support: email: videohelp@idt.com (c) 2007 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered trademarks used to identify products or services of their respective owners. Printed in USA