PB-230 230W Single Output Battery Charger series Features : for lead-acid batteries (flooded,Gel and AGM) and Li-ion batteries (lithium iron and lithium manganese) (Note.1) 3 stage charging characteristic Universal AC input / Full range Built-in active PFC function, PF>0.95 Protection: Short circuit / Overload / Over voltage / Over temperature Built-in cooling Fan ON-OFF control Built-in remote ON-OFF control 2 color LED loading indicator Low cost, high reliability 2 years warranty Charger ( for PB-230-xxAD1 only) ORDER NO. OUTPUT CONNECTOR SAFETY PB-230-xx (standard model) 4pin power din TUV / CE PB-230-xxAD1 (optional model) Anderson connector UL / EAC PB-230-xx xx=12,24,48 ; =Blank, AD1 SPECIFICATION MODEL 57.6V FLOAT CHARGE VOLTAGE 13.6V 27.2V 54.4V 24 ~ 80Ah 12 ~ 40Ah RECOMMENDED BATTERY CAPACITY(AMP HOURS)(Note 5) 50 ~ 160Ah BATTERY TYPE Open & Sealed Lead Acid OUTPUT CURRENT 16A VOLTAGE RANGE 90 ~ 264VAC FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR (Typ.) PF>0.95/230VAC EFFICIENCY (Typ.) 81.5% AC CURRENT (Typ.) INRUSH CURRENT (Typ.) 3A/115VAC 1.5A/230VAC COLD START 50A LEAKAGE CURRENT <3.5mA / 240VAC OVERLOAD 90 ~ 110% rated output current Protection type : Constant current limiting, recovers automatically after fault condition is removed OVER TEMPERATURE 4A PF>0.98/115VAC at full load 85.5% 86% D OVER VOLTAGE 8A 127 ~ 370VDC N PROTECTION PB-230-48 28.8V R INPUT PB-230-24 14.4V N OUTPUT PB-230-12 BOOST CHARGE VOLTAGE 31 ~ 35V 16 ~ 18V Protection type : Shut down o/p voltage, re-power on to recover Protection type : Automatically derate charge current until zero 59 ~ 64V Short: Stop Charging REMOTE CONTROL (CN105) Open: Normal work FUNCTION FAN CONTROL RTH3 50 Fan ON, 45 Fan OFF (Typ.) By NTC TEMPERATURE SENSE WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS SAFETY & WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC (Note 4) EMC EMISSION OTHERS CONNECTOR NOTE -20 ~ +50 (Refer to "Derating Curve") 20 ~ 90% RH non-condensing -40 ~ +85, 10 ~ 95% RH 0.03%/ (0 ~ 50) 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes UL1012 , EAC TP TC 004 (for PB-230-xxAD1 only), TUV EN60950-1,PSE J60950-1 approved I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25/ 70% RH Compliance to EN55032 (CISPR32) Class B, EN61000-3-2,-3, EAC TP TC 020 EMC IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, light industry level, criteria A, EAC TP TC 020 MTBF DIMENSION 244.5Khrs min. MIL-HDBK-217F (25) PACKING PLUG 190*96*49mm(L*W*H) 1.21Kg; 12pcs/15.5Kg/1.29CUFT See page 2 ; Other type available by customer requested CABLE See page 2 ; Other type available by customer requested 1. Modification for charger specification may be required for different battery specification. Please contact MEAN WELL for details. 2. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 3. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 4. Tolerance : includes set up tolerance, line regulation and load regulation. 5. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 6. This is Mean Well's suggested range. Please consult your battery manufacturer for their suggestions about maximum charging current limitation. 7. The ambient temperature derating of 3.5/1000m with fanless models and of 5/1000m with fan models for operating altitude higher than 2000m(6500ft). File Name:PB-230-SPEC 2018-01-12 PB-230 230W Single Output Battery Charger Mechanical Specification Case No.PB-230A series Unit:mm 115cm5cm 3 2 4 AD1 (optional) 1 CN105 12 96 FUSE 352mm Air flow direction Remote Control (CN105) : JST B2B-XH or equivalent 49 Pin No. 1 2 Assignment RCRC+ Mating Housing Terminal JST XHP or equivalent JST SXH-001T-P0.6 or equivalent 190 N Plug Assignment AD1 [ housing: Anderson 1327FP(red), 1327G6FP(black) contacts: Anderson 261G2 (45A) or equivalent ] 4pin XLR UNICABLE 89M103-4P or equivalent 3 2 1 PIN NO. OUTPUT 1,2 +V 3,4 -V N 4 DC output connector (optional) R DC output connector (standard) Red(+V) D Block Diagram Black(-V) FAN ON/OFF CONTROL EMI FILTER & RECTIFIERS I/P RECTIFIERS & FILTER POWER SWITCHING PFC CIRCUIT FG +V -V DETECTION CIRCUIT PWM & PFC CONTROL O.L.P. fosc : 90KHz FAN O.T.P. O.V.P. REMOTE CONTROL Derating Curve Charging Curve Start 100 V boost 90 V FLT Charge Voltage 80 100% Charge Current 10% Constant Current Constant Voltage stage 1 stage 2 Red Color of LED stage 3 Green LOAD (%) 70 60 40 30 -20 10 20 30 40 45 50 60 70 (HORIZONTAL) AMBIENT TEMPERATURE () State V boost V FLT PB-230-12 14.4V 13.6V PB-230-24 28.8V 27.2V PB-230-48 57.6V 54.4V File Name:PB-230-SPEC 2018-01-12