Model B0430J50100A00 Rev D Ultra Low Profile 0805 Balun 50 to 100 Balanced Description The B0430J50100A00 is a low cost, low profile sub-miniature unbalanced to balanced transformer designed specifically for differential inputs and output locations on next generation A to D and D to A Converter IC's in an easy to use surface mount package, covering 400 MHz-3000 MHz. The B0430J50100A00 is ideal for high volume manufacturing and delivers higher performance than traditional wire wound baluns. The B0430J50100A00 has an unbalanced port impedance of 50 and a 100 balanced port impedance. This transformation enables single ended signals to be applied to differential ports. The output ports have equal amplitude (-3dB) with 180 degree phase differential. The B0430J50100A00 is available on tape and reel for pick and place high volume manufacturing. Note that for optimal performance, the B0430J50100A00 should be used with a 10 pF series capacitor on the unbalanced port as shown in p. 2 & 3. Detailed Electrical Specifications: Specifications subject to change without notice. ROOM (25C) Features: * * * * * * * * * * 400 - 3000 MHz 0.7mm Height Profile 50 Ohm to 2 x 50 Ohm Low Insertion Loss Designed for A-D and D-A Converters Input to Output DC Isolation Surface Mountable Tape & Reel Non-conductive Surface RoHS Compliant Parameter Min. Frequency Unbalanced Port Impedance Balanced Port Impedance Return Loss Insertion Loss* Amplitude Balance Phase Balance CMRR Power Handling Operating Temperature 400 Typ. 50 100 9.9 3.4 0.7 7 25 8.4 Max Unit 3000 MHz dB dB dB Degrees dB Watts C 4.0 1.4 12 1 +85 -55 * Insertion Loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 C) Outline Drawing Top View (Near-side) .079.004 [2.000.10] Side View Bottom View (Far-side) .026 [0.65] .027.002 [0.700.05] 1 2 3 .039 [0.98] 6X .009 [0.22] .049.004 [1.250.10] Orientation Marker Denotes Pin Location Dimensions are in Inches [Millimeters] Mechanical Outline Orientation Marker Denotes Pin Location Pin 1 2 3 4 5 6 Designation GND Unbalanced Port GND Balanced Port NC Balanced Port 6 5 6X .012 [0.30] 4 Tolerances are Non-Cumulative Available on Tape and Reel for Pick and Place Manufacturing. USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Model B0430J50100A00 Rev D Typical Performance: 300 MHz. to 3100 MHz. with an External 0603 10 pF capacitor Return Loss - Input 0 -3 -6 -9 -12 [dB] -15 -18 -21 -24 -27 -30 -33 Insertion Loss 3100 2900 2700 2500 2300 2100 1900 Amplitude Balance 0 2 -0.3 1.5 -0.6 -0.9 1 -1.2 0.5 [dB] -1.5 -1.8 -2.1 0 -0.5 -2.4 -2.7 -1 -3 -1.5 -3.3 2100 2300 2500 2700 2900 3100 2100 2300 2500 2700 2900 3100 1900 1700 1500 1300 1100 900 300 3100 2900 2700 2500 2300 2100 1900 1700 1500 1300 1100 900 700 500 300 700 -2 -3.6 500 Frequency [MHz] Frequency [MHz] CM RR Phase Balance 0 20 -3 15 -6 -9 10 -12 5 [dB] -15 0 -18 -21 -5 -24 -10 -27 -30 -15 -33 -20 Frequency [MHz] USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 1900 1700 1300 1100 900 700 500 300 3100 2900 2700 2500 2300 2100 1900 1700 1500 1300 1100 900 700 500 300 -36 1500 [dB] 1700 Frequency [MHz] Schematic of BD0430J50100A00 with 10 pF capacitor on unbalanced port (pin #2) deg 1500 1300 1100 900 700 500 300 -36 Frequency [MHz] Available on Tape and Reel for Pick and Place Manufacturing. Model B0430J50100A00 Rev D Mounting Configuration: This component requires a 0603 10 pF capacitor to be mounted in front of the unbalanced port (Pin 2) of the balun as shown in the drawing below for optimum performance. The capacitor should be placed as close as possible to the balun to minimize transmission line effects as shown in the suggested PCB footprint below. Note however, that in specific designs, the transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances. In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must be used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet published specifications. All of the Xinger components are constructed from ceramic filled PTFE composites which possess excellent electrical o and mechanical stability having X and Y thermal coefficient of expansion (CTE) of 17 ppm/ C. Mounting Footprint C1 Plated thru holes to ground 6X .012 [0.30] Part Orientation (Top View) 6X .010 [0.25] .033 [0.85] 6X .002 [0.05] 3X Transmission Line 4X .014 [0.35] Circuit Pattern Footprint Pad (s) Solder Resist Available on Tape and Reel for Pick and Place Manufacturing. USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Model B0430J50100A00 Rev D Packaging and Ordering Information Parts are available in reel and are packaged per EIA 481-2. Parts are oriented in tape and reel as shown below. Minimum order quantities are 4000 per reel. See Model Numbers below for further ordering information. OA OC OD QUANTITY/REEL 4000 TABLE 1 REEL DIMENSIONS (inches [mm]) OA 7.00 [177.8] B 0.32 [8.0] 2.0 [50.8] OC OD 0.512 [13.0] USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 B Available on Tape and Reel for Pick and Place Manufacturing.