HBD DC-DC Series Data Sheet
30 to 60-Watt, Dual Output
REV. JAN 26, 2005 Page 1 of 3 www.power-one.com
HBD060YGE-A
60
65
70
75
80
85
10 20 30 40 50 60 70 80 90 100
LOAD %
EFF. (1 8V)
EFF. (2 4V)
EFF. (3 6V)
50
55
60
65
70
75
80
85
10 20 30 40 50 60 70 80 90 100
LOAD %
EFFICIENCY %
HBD060ZGE-A
HBD040ZGE-A
HBD0X0ZED-A
Technical Specifications
Voltage Range
24 VDC Nominal 18.00 - 36.00 VDC
48 VDC Nominal 34.00 - 75.00 VDC
Reflected Ripple 80 mA
Input Reverse Voltage Protection Shunt Diode
HBD dual output, dc-dc converters feature high efficiency, 1500 VDC isolation, and open-frame packaging. The HBD
family allows board designers to deliver any combination of power from either output, up to each model’s maximum
rating. The HBD is available in 5V/3.3V or 3.3V/2.5V combinations in either a 24V or 48V input version. The HBD uses
planar magnetics and has an MTBF of over a million hours.
• Independent dual outputs
• Flexible load sharing
• High efficiency topology
• Open-frame design
• Planar magnetics
• Independent trim for each output
• 1500V Isolation
• 100°C baseplate operation
Description
Features
Input
Efficiency vs. Load (24V Input)
Efficiency vs. Load (48V Input)
Notes
1For negative logic, add suffix “N” to model number.
†MTBF predictions may vary slightly from model to model.
Specifications typically at 25°C, normal line, and full load, unless otherwise
stated.
Soldering Conditions: I/O pins, 260°C, ten seconds; fully compatible with
commercial wave-soldering equipment.
Safety: Agency approvals may vary from model to model. Please consult
factory for specific model information.
Units are water-washable and fully compatible with commercial spray or
immersion post wave-solder washing equipment.
Turn-On Time 10 ms
Remote Shutdown Positive Logic
Switching Frequency 500 kHz
Isolation
Input - Output 1500 VDC
Input - Case 1050 VDC
Output - Case 500 VDC
Temperature Coefficient 0.03%/°C
Case Temperature
Operating Range -40 To +100°C
Storage Range -40 To +125°C
Thermal Shutdown Range 105 To 115°C
Humidity Max., Non-Condensing 95%
Vibration, 3 Axes, 5 Min Each 5 g
MTBF†(Bellcore TR-NWT-000332) 1.3 x 106Hrs
Safety UL, cUL, VDE
Weight (approx.) 2.4 oz
General
Setpoint Accuracy ±1%
Line Regulation VinMin. - VinMax., Iout Rated, Output 1 0.2% Vout
Line Regulation VinMin. - VinMax., Iout Rated, Output 2 1.0% Vout
Load Regulation IoutMin. - IoutMax., Vin Nom., Output 1 0.5% Vout
Load Regulation IoutMin. - IoutMax., Vin Nom., Output2 1.0% Vout
Minimum Output Current 10% IoutRated
Dynamic Regulation, Loadstep 25% Iout
Pk Deviation 4% Vout
Settling Time 500 µs
Voltage Trim Range (5V/3.3V Units) ±10%
Power Limit Threshold Range, % of IoutRated 110 - 140%
OVP Trip Range (Main Ouput) 115 - 140% VoutNom.
Output
HBD DC-DC Series Data Sheet
30 to 60-Watt, Dual Output
REV. JAN 26, 2005 Page 2 of 3 www.power-one.com
MODEL INPUT VOLTAGE INPUT VOLTAGE MAXIMUM INPUT OUTPUT RATED OUTPUT RIPPLE & NOISE TYPICAL
(VOLTS) RANGE (VOLTS) CURRENT (AMPS)* VOLTAGE (VOLTS) CURRENT (AMPS)&& pk-pk (mV) EFFICIENCY**
HBD040YED-A 24 18-36 2.89 3.3/2.5 12/15 75/75 75%
HBD060YGE-A 24 18-36 4.54 5.0/3.3 12/15 100/75 78%
HBD040YGE-A 24 18-36 3.02 5.0/3.3 8/12 100/75 80%
HBD030ZED-A 48 34-75 1.50 3.3/2.5 9/12*** 75/75 75%
HBD040ZGE-A 48 34-75 1.51 5.0/3.3 8/12 100/75 80%
HBD040ZED-A 48 34-75 1.62 3.3/2.5 12/15 75/75 75%
HBD060ZGE-A 48 34-75 2.27 5.0/3.3 12/15 75/75 75%
NOTES: * Maximum input current at minimum input voltage, maximum rated output power.
** At nominal Vin, rated output.
*** Total output power to be restricted to 30 Watts.
&& Current can be drawn from either output to its maximum value, or from both outputs to a combined total of 15A.
Thermal Impedance
Natural Convection 6.6 °C/W
100 LFM 5.7 °C/W
200 LFM 4.2 °C/W
300 LFM 3.1 °C/W
400 LFM 2.6 °C/W
Tolerances
Note:
Thermal impedance data is dependent on
many environmental factors. The exact
thermal performance should be validated
for specific application.
Mechanical Drawing
1-V
in
2 Case
3 On/Off
4+V
in
5+V
out 2
6- V
out 2
7 Trim 2
8+V
out 1
9-V
out 1
10 Trim 1
Inches: (Millimeters)
.XX ± 0.020 .X ± 0.5
.XXX ± 0.010 .XX ± 0.25
Pin:
± 0.002 ± 0.05
(Dimensions as listed unless otherwise
specified.)
Pin Function
10
9
8
7
6
5
4
3
2
1
BOTTOM VIEW
SIDE VIEW
(PIN SIDE)
1.500"(38.1mm)
1.200"(30.5mm)
0.900"(22.9mm)
0.500"(12.7mm)
0.200"(5.1mm)
-0.100"(-2.5mm)
1.700"(43.2mm)
-0.50"(-12.7mm)
-0.300"(-7.6mm)
1.400"(35.6mm)
1.000"(25.4mm)
0.400"(10.2mm)
0
(12.7mm)
0.50"
(0.6mm)
.025" REF.
(1.0mm)
DIA 0.040"
(4.6mm)
0.18"
(61.0mm)
2.40
"
(57.9mm)
2.28
"
M3X.5 THROUGH 4PL
MOUNTING INSERTS
0
(-4.8mm)
-0.19"
(48.3mm)
1.900"
Model Selection
REV. JAN 26, 2005 Page 3 of 3 www.power-one.com
Series Applicability: HAS, HBD, HBS, HES, QBS, QES, TES, TQD
Features & Options Descriptions Suffix Code
Remote ON/OFF Positive Logic None
Negative Logic N
Trim Standard Power-One (Negative) None
Industry-standard (Positive) T
Pin Length 0.18” (4.6mm), standard model length None
0.145” (3.68mm) 7
0.110” (2.8mm) 8
Special Options Customer-specific models S#
NOTE: Contact factory for availability of specific options.
NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical compo-
nents in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the
respective divisional president of Power-One, Inc.
TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the
date manufactured. Specifications are subject to change without notice.
Ordering Information
Suffix Code Identification:
OPTIONS
