LTC3851A Synchronous Step-Down Switching Regulator Controller Description Features n n n n n n n n n n n n n n n Wide VIN Range: 4V to 38V Operation RSENSE or DCR Current Sensing 1% Output Voltage Accuracy Phase-Lockable Fixed Frequency: 250kHz to 750kHz Dual N-Channel MOSFET Synchronous Drive Very Low Dropout Operation: 99% Duty Cycle Adjustable Output Voltage Soft-Start or Tracking Output Current Foldback Limiting Output Overvoltage Protection 5V Internal Regulator OPTI-LOOP(R) Compensation Minimizes COUT Selectable Continuous, Pulse-Skipping or Burst Mode(R) Operation at Light Loads Low Shutdown IQ: 20A VOUT Range: 0.8V to 5.5V Thermally Enhanced 16-Lead MSOP, 16-Lead Narrow SSOP or 3mm x 3mm QFN Package The LTC(R)3851A is a high performance synchronous step-down switching regulator controller that drives an all N-channel synchronous power MOSFET stage. A constant frequency current mode architecture allows a phaselockable frequency of up to 750kHz. OPTI-LOOP compensation allows the transient response to be optimized over a wide range of output capacitance and ESR values. The LTC3851A features a precision 0.8V reference that is compatible with a wide 4V to 38V input supply range. The TK/SS pin ramps the output voltage during startup. Current foldback limits MOSFET heat dissipation during short-circuit conditions. The MODE/PLLIN pin selects among Burst Mode operation, pulse-skipping mode or continuous inductor current mode at light loads and allows the IC to be synchronized to an external clock. The LTC3851A contains an improved PLL compared to the LTC3851. Applications n n n n Automotive Systems Telecom Systems Industrial Equipment Distributed DC Power Systems The LTC3851A-1 is a version with a power good output signal instead of adjustable current limit. L, LT, LTC, LTM, Burst Mode, OPTI-LOOP, Linear Technology and the Linear logo are registered trademarks and No RSENSE, UltraFast are trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. Protected by U.S. Patents including 5408150, 5481178, 5705919, 5929620, 6304066, 6498466, 6580258, 6611131. Typical Application High Efficiency Synchronous Step-Down Converter VIN FREQ/PLLFLTR TG 82.5k 0.1F INTVCC 2200pF BG ITH 15k 0.68H 330F x2 3.01k 4.7F 0.047F SENSE- 90 EFFICIENCY 85 1000 80 75 POWER LOSS 70 100 65 60 SENSE+ MODE/PLLIN 10000 VIN = 12V 95 VOUT = 3.3V VOUT 3.3V 15A 0.1F GND 330pF 100 POWER LOSS (mW) 0.1F RUN SW LTC3851A BOOST TK/SS VIN 4.5V TO 36V 22F EFFICIENCY (%) ILIM Efficiency and Power Loss vs Load Current 30.1k 55 154k VFB 48.7k 50 10 100 1000 10000 LOAD CURRENT (mA) 10 100000 3851A TA01b 3851A TA01a 3851afa 1 LTC3851A Absolute Maximum Ratings (Note 1) Input Supply Voltage (VIN).......................... 40V to -0.3V Topside Driver Voltage (BOOST)................. 46V to -0.3V Switch Voltage (SW)...................................... 40V to -5V INTVCC, (BOOST - SW), RUN....................... 6V to -0.3V TK/SS, ILIM............................................INTVCC to -0.3V SENSE+, SENSE-........................................... 6V to -0.3V MODE/PLLIN, FREQ/PLLFLTR...............INTVCC to -0.3V ITH, VFB Voltages........................................... 3V to -0.3V INTVCC Peak Output Current...................................50mA Operating Junction Temperature Range (Notes 2, 3) E-Grade, I-Grade................................. -40C to 125C H-Grade.............................................. -40C to 150C MP-Grade........................................... -55C to 150C Storage Temperature Range................... -65C to 150C Lead Temperature (Soldering, 10 sec) GN/MSE............................................................. 300C Pin Configuration 3 14 BOOST TK/SS 4 13 VIN ITH 5 12 INTVCC FB 6 11 BG SENSE- 7 10 GND SENSE+ 8 9 ILIM GN PACKAGE 16-LEAD PLASTIC SSOP NARROW 1 2 3 4 5 6 7 8 17 GND 16 15 14 13 12 11 10 9 SW TG BOOST VIN INTVCC BG GND ILIM MSE PACKAGE 16-LEAD PLASTIC MSOP TJMAX = 125C, JA = 35C/W TO 40C/W EXPOSED PAD (PIN 17) IS GND, MUST BE SOLDERED TO PCB TJMAX = 125C, JA = 110C/W TG RUN TOP VIEW MODE/PLLIN FREQ/PLLFLTR RUN TK/SS ITH FB SENSE- SENSE+ 16 15 14 13 12 BOOST RUN 1 TK/SS 2 11 VIN 17 GND ITH 3 10 INTVCC FB 4 9 5 6 7 8 GND 15 TG ILIM 16 SW 2 SENSE+ 1 SENSE- MODE/PLLIN FREQ/PLLFLTR SW TOP VIEW MODE/PLLIN FREQ/PLLFLTR TOP VIEW BG UD PACKAGE 16-LEAD (3mm x 3mm) PLASTIC QFN TJMAX = 125C, JA = 68C/W, JC = 4.2C/W EXPOSED PAD (PIN 17) IS GND, MUST BE SOLDERED TO PCB Order Information LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LTC3851AEGN#PBF LTC3851AEGN#TRPBF 3851A 16-Lead Plastic SSOP -40C to 125C LTC3851AIGN#PBF LTC3851AIGN#TRPBF 3851A 16-Lead Plastic SSOP -40C to 125C LTC3851AEMSE#PBF LTC3851AEMSE#TRPBF 3851A 16-Lead Plastic MSOP -40C to 125C LTC3851AIMSE#PBF LTC3851AIMSE#TRPBF 3851A 16-Lead Plastic MSOP -40C to 125C LTC3851AHMSE#PBF LTC3851AHMSE#TRPBF 3851A 16-Lead Plastic MSOP -40C to 150C LTC3851AMPMSE#PBF LTC3851AMPMSE#TRPBF 3851A 16-Lead Plastic MSOP -55C to 150C LTC3851AEUD#PBF LTC3851AEUD#TRPBF LFPZ 16-Lead (3mm x 3mm) Plastic QFN -40C to 125C LTC3851AIUD#PBF LTC3851AIUD#TRPBF LFPZ 16-Lead (3mm x 3mm) Plastic QFN -40C to 125C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. Consult LTC Marketing for information on non-standard lead based finish parts. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ 3851afa 2 LTC3851A Electrical Characteristics The l denotes the specifications which apply over the specified operating temperature range, otherwise specifications are at TA = 25C (Note 2). VIN = 15V, VRUN = 5V unless otherwise noted. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS Main Control Loops VIN Operating Input Voltage Range VFB Regulated Feedback Voltage ITH = 1.2V (Note 4) 0C to 85C ITH = 1.2V (Note 4) -40C to 125C ITH = 1.2V (Note 4) -40C to 150C ITH = 1.2V (Note 4) -55C to 150C IFB Feedback Current (Note 4) VREFLNREG Reference Voltage Line Regulation VIN = 6V to 38V (Note 4) VLOADREG Output Voltage Load Regulation (Note 4) Measured in Servo Loop, ITH = 1.2V to 0.7V (Note 4) Measured in Servo Loop, ITH = 1.2V to 0.7V (H-Grade, MP-Grade) (Note 4) Measured in Servo Loop, ITH = 1.2V to 1.6V (Note 4) Measured in Servo Loop, ITH = 1.2V to 1.6V (H-Grade, MP-Grade) l 4 l l l l 0.792 0.788 0.788 0.788 l 0.800 V 0.808 0.812 0.812 0.812 V V V V -10 -50 nA 0.002 0.02 %/V 0.01 0.1 % 0.2 % -0.1 % -0.2 % l -0.01 l 38 l gm Transconductance Amplifier gm ITH = 1.2V, Sink/Source = 5A (Note 4) 2 mmho gm GBW Transconductance Amp Gain Bandwidth ITH = 1.2V (Note 8) 3 MHz IQ Input DC Supply Current Normal Mode Shutdown (Note 5) VRUN = 5V VRUN = 0V 1.2 25 VINTVCC Ramping Down 3.25 V 0.4 V UVLO Undervoltage Lockout on INTVCC UVLO Hys UVLO Hysteresis VOVL Feedback Overvoltage Lockout VFB with Respect to Set Regulated Voltage VFB Ramping Positive (OV) 7.5 0.6 1.10 ISENSE SENSE Pins Current ITK/SS Soft-Start Charge Current VTK/SS = 0V VRUN RUN Pin On--Threshold VRUN Rising VRUNHYS RUN Pin On--Hysteresis VSENSE(MAX) Maximum Current Sense Threshold l 50 10 12.5 % 1 2 A 1 2 A 1.22 1.35 120 VFB = 0.7V, VSENSE = 3.3V, ILIM = 0V VFB = 0.7V, VSENSE = 3.3V, ILIM = 0V (H-/MP-Grade) VFB = 0.7V, VSENSE = 3.3V, ILIM = Float VFB = 0.7V, VSENSE = 3.3V, ILIM = Float (H-/MP-Grade) VFB = 0.7V, VSENSE = 3.3V, ILIM = INTVCC VFB = 0.7V, VSENSE = 3.3V, ILIM = INTVCC (H-/MP-Grade) l l l l l l 20 15 40 35 65 60 mA A 30 53 80 V mV 40 45 65 70 95 100 mV mV mV mV mV mV TG RUP TG Driver Pull-Up On-Resistance TG High 2.2 TG RDOWN TG Driver Pull-Down On-Resistance TG Low 1.2 BG RUP BG Driver Pull-Up On-Resistance BG High 2.1 BG RDOWN BG Driver Pull-Down On-Resistance BG Low 1.1 TG tr TG tf TG Transition Time Rise Time Fall Time (Note 6) CLOAD = 3300pF CLOAD = 3300pF 25 25 ns ns BG tr BG tf BG Transition Time Rise Time Fall Time (Note 6) CLOAD = 3300pF CLOAD = 3300pF 25 25 ns ns TG/BG t1D Top Gate Off to Bottom Gate On Delay Bottom Switch-On Delay Time CLOAD = 3300pF Each Driver (Note 6) 30 ns BG/TG t2D Bottom Gate Off to Top Gate On Delay Top CLOAD = 3300pF Each Driver Switch-On Delay Time (Note 6) 30 ns tON(MIN) Minimum On-Time 90 ns (Note 7) 3851afa 3 LTC3851A Electrical Characteristics The l denotes the specifications which apply over the specified operating temperature range, otherwise specifications are at TA = 25C (Note 2). VIN = 15V, VRUN = 5V unless otherwise noted. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS 4.8 5 5.2 V 0.5 2 % INTVCC Linear Regulator VINTVCC Internal VCC Voltage 6V < VIN < 38V VLDO INT INTVCC Load Regulation ICC = 0mA to 50mA Oscillator and Phase-Locked Loop fNOM Nominal Frequency RFREQ = 60k 460 500 540 kHz fLOW Lowest Frequency RFREQ = 160k 205 235 265 kHz fHIGH Highest Frequency RFREQ = 36k 690 750 810 kHz RMODE/PLLIN MODE/PLLIN Input Resistance 100 k fMODE MODE/PLLIN Minimum Input Frequency MODE/PLLIN Maximum Input Frequency VMODE = External Clock VMODE = External Clock 250 750 kHz kHz IFREQ Phase Detector Output Current Sinking Capability Sourcing Capability fMODE > fOSC fMODE < fOSC -90 75 A A Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LTC3851A is tested under pulsed load conditions such that TA TJ. The LTC3851AE is guaranteed to meet performance specifications from 0C to 85C junction temperature. Specifications over the -40C to 125C operating junction temperature range are assured by design, characterization and correlation with statistical process controls. The LTC3851AI is guaranteed to meet specifications over the -40C to 125C operating junction temperature range, the LTC3851AH is guaranteed over the -40C to 150C operating junction temperature range and the LTC3851AMP is tested and guaranteed over the -55C to 150C operating junction temperature range. High junction temperatures degrade operating lifetimes; operating lifetime is derated for junction temperatures greater than 125C. Note that the maximum ambient temperature consistent with these specifications is determined by specific operating conditions in conjunction with board layout, the rated package thermal impedance and other environmental factors. Note 3: TJ is calculated from the ambient temperature TA and power dissipation PD according to the following formulas: LTC3851AGN: TJ = TA + (PD * 110C/W) LTC3851AUD: TJ = TA + (PD * 68C/W) LTC3851AMSE: TJ = TA + (PD * 40C/W) Note 4: The LTC3851A is tested in a feedback loop that servos VITH to a specified voltage and measures the resultant VFB. Note 5: Dynamic supply current is higher due to the gate charge being delivered at the switching frequency. See Applications Information. Note 6: Rise and fall times are measured using 10% and 90% levels. Delay times are measured using 50% levels. Rise and fall times are assured by design, characterization and correlation with statistical process controls. Note 7: The minimum on-time condition is specified for an inductor peak-to-peak ripple current ~40% of IMAX (see Minimum On-Time Considerations in the Applications Information section). Note 8: Guaranteed by design; not tested in production. Typical Performance Characteristics Efficiency vs Output Current and Mode Efficiency vs Output Current and Mode 100 100 VIN = 12V 90 VOUT = 1.5V EFFICIENCY(%) 50 40 CCM 30 60 40 CCM 30 20 10 10 0 0 100 1000 10000 LOAD CURRENT (mA) PULSE SKIP 50 20 10 90 80 70 PULSE SKIP 60 100 BURST 80 BURST 70 EFFICIENCY(%) 90 EFFICIENCY (%) 80 Efficiency vs Output Current and Mode 100000 3851A G01 VIN = 12V VOUT = 3.3V FIGURE 11 CIRCUIT 10 100 1000 10000 LOAD CURRENT (mA) 100000 3851A G02 BURST 70 PULSE SKIP 60 50 CCM 40 30 20 VIN = 12V VOUT = 5V 10 0 10 100 1000 10000 LOAD CURRENT (mA) 100000 3851A G03 3851afa 4 LTC3851A Typical Performance Characteristics Efficiency and Power Loss vs Input Voltage Load Step (Burst Mode Operation) 100 10000 EFFICIENCY, IOUT = 5A POWER LOSS, IOUT = 5A 90 85 80 POWER LOSS, IOUT = 0.5A 75 70 1000 EFFICIENCY, IOUT = 0.5A 4 8 VIN = 12V VOUT = 3.3V FIGURE 11 CIRCUIT 16 12 24 20 INPUT VOLTAGE (V) 28 32 POWER LOSS (mW) EFFICIENCY (%) 95 ILOAD 5A/DIV 0.2A TO 7.5A IL 5A/DIV VOUT 100mV/DIV AC-COUPLED VOUT = 1.5V 100s/DIV VIN = 12V FIGURE 11 CIRCUIT 100 3851A G05 3851A G04 Load Step (Forced Continuous Mode) Load Step (Pulse-Skipping Mode) ILOAD 5A/DIV 0.2A TO 7.5A ILOAD 5A/DIV 0.2A TO 7.5A IL 5A/DIV IL 5A/DIV VOUT 100mV/DIV AC-COUPLED VOUT 100mV/DIV AC-COUPLED 3851A G06 VOUT = 1.5V 100s/DIV VIN = 12V FIGURE 11 CIRCUIT VOUT = 1.5V 100s/DIV VIN = 12V FIGURE 11 CIRCUIT Start-Up with Prebiased Output at 2V Inductor Current at Light Load FORCED CONTINOUS MODE 5A/DIV VOUT 2V/DIV Burst Mode OPERATION 5A/DIV TK/SS 0.5V/DIV 3851A G07 Coincident Tracking with Master Supply VMASTER 0.5V/DIV VOUT 2A LOAD 0.5V/DIV VFB 0.5V/DIV PULSE-SKIPPING MODE 5A/DIV VOUT = 1.5V 1s/DIV VIN = 12V ILOAD = 1mA FIGURE 11 CIRCUIT 3851A G08 20ms/DIV 3851A G09 10ms/DIV 3851A G10 3851afa 5 LTC3851A Typical Performance Characteristics Ratiometric Tracking with Master Supply Input DC Supply Current vs Input Voltage INTVCC Line Regulation 3.0 5.3 SUPPLY CURRENT (mA) VOUT 2A LOAD 0.5V/DIV 3851A G11 10ms/DIV INTVCC VOLTAGE (V) 2.5 VMASTER 0.5V/DIV 2.0 1.5 1.0 ILOAD = 0mA 4.9 ILOAD = 25mA 4.7 4.5 4.3 4.1 3.9 0.5 0 5.1 3.7 4 8 12 16 20 24 28 32 INPUT VOLTAGE (V) 36 3.5 40 4 8 12 16 20 24 28 32 INPUT VOLTAGE (V) 3851A G12 Maximum Current Sense Threshold vs Common Mode Voltage 90 90 ILIM = INTVCC 80 70 40 ILIM = GND 30 MAXIMUIM 50 ILIM = INTVCC 50 ILIM = FLOAT 40 30 ILIM = GND 20 40 30 20 10 20 MINIMUIM 0 10 10 ILIM = FLOAT BURST COMPARATOR FALLING THESHOLD: VITH = 0.4V 0 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 VITH (V) -10 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 VSENSE COMMON MODE VOLTAGE (V) -20 5 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 VITH (V) 3851A G16 3851A G15 3851A G14 Maximum Current Sense Threshold vs Feedback Voltage (Current Foldback) Maximum Current Sense Threshold vs Duty Cycle TK/SS Pull-Up Current vs Temperature 1.5 90 ILIM = INTVCC 80 MAXIMUM VSENSE (mV) 70 60 ILIM = FLOAT 50 40 ILIM = GND 30 20 40 100 3851A G17 ILIM = GND 30 20 0 80 ILIM = FLOAT 50 0 60 40 DUTY CYCLE (%) 1.3 60 10 20 1.4 70 10 0 ILIM = INTVCC 80 TK/SS CURRENT (A) 90 CURRENT SENSE THRESHOLD (mV) 60 DUTY CYCLE RANGE: 0% TO 100% VSENSE (mV) ILIM = FLOAT 50 0 Burst Mode Peak Current Sense Threshold vs ITH Voltage 60 60 40 3851A G13 Maximum Peak Current Sense Threshold vs ITH Voltage 70 VSENSE (mV) VSENSE THRESHOLD (mV) 80 36 1.2 1.1 1.0 0.9 0.8 0.7 0.6 0 0.1 0.2 0.3 0.4 0.5 0.6 FEEDBACK VOLTAGE (V) 0.7 0.8 3851A G18 0.5 -75 -50 -25 0 25 50 75 100 125 150 TEMPERATURE (C) 3851A G19 3851afa 6 LTC3851A Typical Performance Characteristics 1.4 RUN RISING THRESHOLD (ON) 1.2 RUN FALLING THRESHOLD (OFF) 1.1 1.0 802 800 798 796 794 -75 -50 -25 0 25 50 75 100 125 150 TEMPERATURE (C) INTVCC VOLTAGE AT UVLO THRESHOLD (V) FREQUENCY (kHz) 410 405 400 395 390 385 30 25 20 INPUT VOLTAGE (V) 15 35 40 4 INTVCC RAMPING UP 3 INTVCC RAMPING DOWN 2 1 0 -75 -50 -25 35 30 25 20 15 10 5 0 0 25 50 75 100 125 150 TEMPERATURE (C) 20 15 10 5 0 25 50 75 100 125 150 TEMPERATURE (C) 3851A G26 5 10 15 20 25 30 INPUT VOLTAGE (V) 40 90 80 2.5 2.0 1.5 1.0 0.5 0 -75 -50 -25 35 Maximum Current Sense Threshold vs INTVCC Voltage MAXIMUM VSENSE (mV) 25 0 3851A G25 3.0 40 INPUT DC SUPPLY CURRENT (mA) SHUTDOWN INPUT DC SUPPLY CURRENT (A) Shutdown Input DC Supply Current vs Input Voltage Input DC Supply Current vs Temperature 30 0 25 50 75 100 125 150 TEMPERATURE (C) 3851A G24 Shutdown Input DC Supply Current vs Temperature 35 RPLLLPF = 160k 40 3851A G23 0 -75 -50 -25 400 3851A G22 5 415 RPLLLPF = 60k 500 Undervoltage Lockout Threshold (INTVCC) vs Temperature RFREQ = 80k 10 600 3851A G21 Oscillator Frequency vs Input Voltage 5 700 200 -75 -50 -25 0 25 50 75 100 125 150 TEMPERATURE (C) 3851A G20 420 RPLLLPF = 36k 300 SHUTDOWN SUPPLY CURRENT (A) 0.9 -75 -50 -25 800 804 FREQUENCY (kHz) REGULATED FEEDBACK VOLTAGE (mV) RUN PIN VOLTAGE (V) 900 806 1.3 380 Oscillator Frequency vs Temperature Regulated Feedback Voltage vs Temperature Shutdown (RUN) Threshold vs Temperature ISET = INTVCC 70 60 50 40 30 ISET = FLOAT ISET = GND 20 10 0 25 50 75 100 125 150 TEMPERATURE (C) 3851A G27 0 3.2 3.4 3.6 3.8 4.0 4.2 4.4 4.6 4.8 5.0 INTVCC VOLTAGE(V) 3851A G28 3851afa 7 LTC3851A Pin Functions (GN and MSE/UD) MODE/PLLIN (Pin 1/Pin 15): Forced Continuous Mode, Burst Mode or Pulse-Skipping Mode Selection Pin and External Synchronization Input to Phase Detector Pin. Connect this pin to INTVCC to force continuous conduction mode of operation. Connect to GND to enable pulse-skipping mode of operation. To select Burst Mode operation, tie this pin to INTVCC through a resistor no less than 50k, but no greater than 250k. A clock on the pin will cause the controller to operate in forced continuous mode of operation and synchronize the internal oscillator. ILIM (Pin 9/Pin 7): Current Comparator Sense Voltage Range Input. Tying this pin to GND, FLOAT or INTVCC selects the maximum current sense threshold from three different levels. FREQ/PLLFLTR (Pin 2/Pin 16): The phase-locked loop's lowpass filter is tied to this pin. Alternatively, a resistor can be connected between this pin and GND to vary the frequency of the internal oscillator. BG (Pin 11/Pin 9): Bottom Gate Driver Output. This pin drives the gate of the bottom N-channel MOSFET between GND and INTVCC. RUN (Pin 3/Pin 1): Run Control Input. A voltage above 1.22V on this pin turns on the IC. However, forcing this pin below 1.1V causes the IC to shut down the IC. There is a 2A pull-up current on this pin. TK/SS (Pin 4/Pin 2): Output Voltage Tracking and Soft-Start Input. A capacitor to ground at this pin sets the ramp rate for the output voltage. An internal soft-start current of of 1A charges this capacitor. ITH (Pin 5/Pin 3): Current Control Threshold and Error Amplifier Compensation Point. The current comparator tripping threshold increases with its ITH control voltage. FB (Pin 6/Pin 4): Error Amplifier Feedback Input. This pin receives the remotely sensed feedback voltage from an external resistive divider across the output. SENSE- (Pin 7/Pin 5): Current Sense Comparator Inverting Input. The (-) input to the current comparator is connected to the output. GND (Pin 10/Pin 8, Exposed Pad Pin 17): Ground. All small-signal components and compensation components should be Kelvin connected to this ground. The (-) terminal of CVCC and the (-) terminal of CIN should be closely connected to this pin. The exposed pad should be soldered to ground for good thermal conductivity. INTVCC (Pin 12/Pin 10): Internal 5V Regulator Output. The control circuit is powered from this voltage. Decouple this pin to GND with a minimum 2.2F low ESR tantalum or ceramic capacitor. VIN (Pin 13/Pin 11): Main Input Supply. Decouple this pin to GND with a capacitor. BOOST (Pin 14/Pin 12): Boosted Floating Driver Supply. The (+) terminal of the boost-strap capacitor is connected to this pin. This pin swings from a diode voltage drop below INTVCC up to VIN + INTVCC. TG (Pin 15/Pin 13): Top Gate Driver Output. This is the output of a floating driver with a voltage swing equal to INTVCC superimposed on the switch node voltage. SW (Pin 16/Pin 14): Switch Node Connection to the Inductor. Voltage swing at this pin is from a Schottky diode (external) voltage drop below ground to VIN. SENSE+ (Pin 8/Pin 6): Current Sense Comparator Noninverting Input. The (+) input to the current comparator is normally connected to the DCR sensing network or current sensing resistor. 3851afa 8 LTC3851A Functional Diagram FREQ/PLLFLTR VIN MODE/PLLIN + 100k 5V REG 0.8V MODE/SYNC DETECT + - PLL-SYNC VIN CIN BOOST OSC BURSTEN S R CB TG PULSE SKIP Q M1 SW 5k + ON - IREV ICMP + - SWITCH LOGIC AND ANTISHOOT THROUGH SENSE+ DB L1 VOUT SENSE- RUN INTVCC + ILIM BG OV COUT M2 CVCC SLOPE COMPENSATION GND INTVCC UVLO 1 100k ITHB + R2 VFB OV - - + SS + - RUN 0.88V + 1A EA - + + 0.8V REF R1 - SLEEP VIN 0.64V 1.22V 2A 0.4V 3851A FD ITH RC RUN TK/SS CSS CC1 3851afa 9 LTC3851A Operation Main Control Loop The LTC3851A is a constant frequency, current mode step-down controller. During normal operation, the top MOSFET is turned on when the clock sets the RS latch, and is turned off when the main current comparator, ICMP , resets the RS latch. The peak inductor current at which ICMP resets the RS latch is controlled by the voltage on the ITH pin, which is the output of the error amplifier, EA. The VFB pin receives the voltage feedback signal, which is compared to the internal reference voltage by the EA. When the load current increases, it causes a slight decrease in VFB relative to the 0.8V reference, which in turn causes the ITH voltage to increase until the average inductor current matches the new load current. After the top MOSFET has turned off, the bottom MOSFET is turned on until either the inductor current starts to reverse, as indicated by the reverse current comparator, IREV, or the beginning of the next cycle. INTVCC Power Power for the top and bottom MOSFET drivers and most other internal circuitry is derived from the INTVCC pin. An internal 5V low dropout linear regulator supplies INTVCC power from VIN. The top MOSFET driver is biased from the floating boot strap capacitor, CB, which normally recharges during each off cycle through an external diode when the top MOSFET turns off. If the input voltage, VIN , decreases to a voltage close to VOUT, the loop may enter dropout and attempt to turn on the top MOSFET continuously. The dropout detector detects this and forces the top MOSFET off for about 1/10 of the clock period every tenth cycle to allow CB to recharge. However, it is recommended that there is always a load present during the drop-out transition to ensure CB is recharged. Shutdown and Start-Up (RUN and TK/SS) The LTC3851A can be shut down using the RUN pin. Pulling this pin below 1.1V disables the controller and most of the internal circuitry, including the INTVCC regulator. Releasing the RUN pin allows an internal 2A current to pull up the pin and enable that controller. Alternatively, the RUN pin may be externally pulled up or driven directly by logic. Be careful not to exceed the absolute maximum rating of 6V on this pin. The start-up of the controller's output voltage, VOUT , is controlled by the voltage on the TK/SS pin. When the voltage on the TK/SS pin is less than the 0.8V internal reference, the LTC3851A regulates the VFB voltage to the TK/SS pin voltage instead of the 0.8V reference. This allows the TK/SS pin to be used to program a soft-start by connecting an external capacitor from the TK/SS pin to GND. An internal 1A pull-up current charges this capacitor creating a voltage ramp on the TK/SS pin. As the TK/SS voltage rises linearly from 0V to 0.8V (and beyond), the output voltage VOUT rises smoothly from zero to its final value. Alternatively, the TK/SS pin can be used to cause the start-up of VOUT to track another supply. Typically, this requires connecting to the TK/SS pin an external resistor divider from the other supply to ground (see the Applications Information section). When the RUN pin is pulled low to disable the controller, or when INTVCC drops below its undervoltage lockout threshold of 3.2V, the TK/SS pin is pulled low by an internal MOSFET. When in undervoltage lockout, the controller is disabled and the external MOSFETs are held off. Light Load Current Operation (Burst Mode Operation, Pulse-Skipping or Continuous Conduction) The LTC3851A can be enabled to enter high efficiency Burst Mode operation, constant frequency pulse-skipping mode or forced continuous conduction mode. To select forced continuous operation, tie the MODE/PLLIN pin to INTVCC. To select pulse-skipping mode of operation, float the MODE/PLLIN pin or tie it to GND. To select Burst Mode operation, tie MODE/PLLIN to INTVCC through a resistor no less than 50k, but no greater than 250k. When the controller is enabled for Burst Mode operation, the peak current in the inductor is set to approximately one-forth of the maximum sense voltage even though the voltage on the ITH pin indicates a lower value. If the average inductor current is higher than the load current, 3851afa 10 LTC3851A Operation the error amplifier, EA, will decrease the voltage on the ITH pin. When the ITH voltage drops below 0.4V, the internal sleep signal goes high (enabling sleep mode) and both external MOSFETs are turned off. In sleep mode, the load current is supplied by the output capacitor. As the output voltage decreases, the EA's output begins to rise. When the output voltage drops enough, the sleep signal goes low, and the controller resumes normal operation by turning on the top external MOSFET on the next cycle of the internal oscillator. When a controller is enabled for Burst Mode operation, the inductor current is not allowed to reverse. The reverse current comparator, IREV , turns off the bottom external MOSFET just before the inductor current reaches zero, preventing it from revers ing and going negative. Thus, the controller operates in discontinuous operation. In forced continuous operation, the inductor current is allowed to reverse at light loads or under large transient conditions. The peak inductor cur rent is determined by the voltage on the ITH pin, just as in normal operation. In this mode the efficiency at light loads is lower than in Burst Mode operation. However, continuous mode has the advantages of lower output ripple and less interference to audio circuitry. When the MODE/PLLIN pin is connected to GND, the LTC3851A operates in PWM pulse-skipping mode at light loads. At very light loads the current comparator, ICMP, may remain tripped for several cycles and force the external top MOSFET to stay off for the same number of cycles (i.e., skipping pulses). The inductor current is not allowed to reverse (discontinuous operation). This mode, like forced continuous operation, exhibits low output ripple as well as low audio noise and reduced RF interference as compared to Burst Mode operation. It provides higher low current efficiency than forced continuous mode, but not nearly as high as Burst Mode operation. Frequency Selection and Phase-Locked Loop (FREQ/PLLFLTR and MODE/PLLIN Pins) The selection of switching frequency is a trade-off between efficiency and component size. Low frequency operation increases efficiency by reducing MOSFET switching losses, but requires larger inductance and/or capacitance to maintain low output ripple voltage. The switching frequency of the LTC3851A can be selected using the FREQ/ PLLFLTR pin. If the MODE/PLLIN pin is not being driven by an external clock source, the FREQ/PLLFLTR pin can be used to program the controller's operating frequency from 250kHz to 750kHz. A phase-locked loop (PLL) is available on the LTC3851A to synchronize the internal oscillator to an external clock source that is connected to the MODE/PLLIN pin. The controller operates in forced continuous mode of operation when it is synchronized. A series RC should be connected between the FREQ/PLLFLTR pin and GND to serve as the PLL's loop filter. It is suggested that the external clock be applied before enabling the controller unless a second resistor is connected in parallel with the series RC network. The second resistor prevents very low switching frequency operation if the controller is enabled before the clock. Output Overvoltage Protection An overvoltage comparator, OV, guards against transient overshoots (>10%) as well as other more serious con ditions that may overvoltage the output. In such cases, the top MOSFET is turned off and the bottom MOSFET is turned on until the overvoltage condition is cleared. 3851afa 11 LTC3851A Applications Information The Typical Application on the first page of this data sheet is a basic LTC3851A application circuit. The LTC3851A can be configured to use either DCR (inductor resistance) sensing or low value resistor sensing. The choice of the two current sensing schemes is largely a design trade-off between cost, power consumption and accuracy. DCR sensing is becoming popular because it saves expensive current sensing resistors and is more power efficient, especially in high current applications. However, current sensing resistors provide the most accurate current limits for the controller. Other external component selection is driven by the load requirement, and begins with the selection of RSENSE (if RSENSE is used) and the inductor value. Next, the power MOSFETs and Schottky diodes are selected. Finally, input and output capacitors are selected. The circuit shown on the first page can be configured for operation up to 38V at VIN. Current Limit Programming The ILIM pin is a tri-level logic input to set the maximum current limit of the controller. When ILIM is grounded, the maximum current limit threshold of the current compara tor is programmed to be 30mV. When ILIM is floated, the maximum current limit threshold is 50mV. When ILIM is tied to INTVCC , the maximum current limit threshold is set to 75mV. SENSE+ and SENSE- Pins The SENSE+ and SENSE- pins are the inputs to the current comparators. The common mode input voltage range of the current comparators is 0V to 5.5V. Both SENSE pins are high impedance inputs with small base currents of less than 1A. When the SENSE pins ramp up from 0V to 1.4V, the small base currents flow out of the SENSE pins. When the SENSE pins ramp down from 5V to 1.1V, the small base currents flow into the SENSE pins. The high impedance inputs to the current comparators allow accurate DCR sensing. However, care must be taken not to float these pins during normal operation. Low Value Resistors Current Sensing A typical sensing circuit using a discrete resistor is shown in Figure 1. RSENSE is chosen based on the required output current. 12 VIN INTVCC VIN BOOST TG LTC3851A RSENSE SW VOUT BG GND SENSE+ SENSE- FILTER COMPONENTS PLACED NEAR SENSE PINS 3851A F01 Figure 1. Using a Resistor to Sense Current with the LTC3851A The current comparator has a maximum threshold, VMAX , determined by the ILIM setting. The current comparator threshold sets the maximum peak of the inductor current, yielding a maximum average output current, IMAX, equal to the maximum peak value less half the peak-to-peak ripple current, IL. Allowing a margin of 20% for variations in the IC and external component values yields: RSENSE = 0.8 * VMAX IMAX + IL /2 Inductor DCR Sensing For applications requiring the highest possible efficiency, the LTC3851A is capable of sensing the voltage drop across the inductor DCR, as shown in Figure 2. The DCR of the inductor represents the small amount of DC winding resistance of the copper, which can be less than 1m for today's low value, high current inductors. If the external R1||R2 * C1 time constant is chosen to be exactly equal to the L/DCR time constant, the voltage drop across the external capacitor is equal to the voltage drop across the inductor DCR multiplied by R2/(R1 + R2). Therefore, R2 may be used to scale the voltage across the sense terminals when the DCR is greater than the target sense resistance. Check the manufacturer's data sheet for specifications regarding the inductor DCR, in order to properly dimension the external filter components. The DCR of the inductor can also be measured using a good RLC meter. 3851afa LTC3851A Applications Information VIN INTVCC BOOST INDUCTOR TG LTC3851A Accepting larger values of IL allows the use of low inductances, but results in higher output voltage ripple and greater core losses. A reasonable starting point for setting ripple current is IL = 0.3(IMAX). The maximum IL occurs at the maximum input voltage. VIN L SW DCR VOUT BG GND R1 SENSE+ C1* R2 SENSE- *PLACE C1 NEAR SENSE+, SENSE- PINS R1||R2 * C1 = L DCR RSENSE(EQ) = DCR 3851A F02 R2 R1 + R2 Figure 2. Current Mode Control Using the Inductor DCR Slope Compensation and Inductor Peak Current Slope compensation provides stability in constant frequency architectures by preventing sub-harmonic oscillations at high duty cycles. It is accomplished internally by adding a compensating ramp to the inductor current signal. Normally, this results in a reduction of maximum inductor peak current for duty cycles > 40%. However, the LTC3851A uses a novel scheme that allows the maximum inductor peak current to remain unaffected throughout all duty cycles. Inductor Value Calculation The operating frequency and inductor selection are inter related in that higher operating frequencies allow the use of smaller inductor and capacitor values. A higher frequency generally results in lower efficiency because of MOSFET gate charge losses. In addition to this basic trade-off, the effect of inductor value on ripple current and low current operation must also be considered. The inductor value has a direct effect on ripple current. The inductor ripple current IL decreases with higher inductance or frequency and increases with higher VIN: IL = V 1 VOUT 1- OUT f *L VIN The inductor value also has secondary effects. The tran sition to Burst Mode operation begins when the average inductor current required results in a peak current below 10% of the current limit determined by RSENSE. Lower inductor values (higher IL) will cause this to occur at lower load currents, which can cause a dip in efficiency in the upper range of low current operation. In Burst Mode operation, lower inductance values will cause the burst frequency to increase. Inductor Core Selection Once the value for L is known, the type of inductor must be selected. High efficiency converters generally cannot afford the core loss found in low cost powdered iron cores, forcing the use of more expensive ferrite or molypermalloy cores. Actual core loss is independent of core size for a fixed inductor value, but it is very dependent on inductance selected. As inductance increases, core losses go down. Unfortunately, increased inductance requires more turns of wire and therefore copper losses will increase. Ferrite designs have very low core loss and are preferred at high switching frequencies, so design goals can con centrate on copper loss and preventing saturation. Ferrite core material saturates hard, which means that induc tance collapses abruptly when the peak design current is exceeded. This results in an abrupt increase in inductor ripple current and consequent output voltage ripple. Do not allow the core to saturate! Power MOSFET and Schottky Diode (Optional) Selection Two external power MOSFETs must be selected for the LTC3851A controller: one N-channel MOSFET for the top (main) switch, and one N-channel MOSFET for the bottom (synchronous) switch. 3851afa 13 LTC3851A Applications Information The peak-to-peak drive levels are set by the INTVCC voltage. This voltage is typically 5V during start-up. Consequently, logic-level threshold MOSFETs must be used in most applications. The only exception is if low input voltage is expected (VIN < 5V); then, sub-logic level threshold MOSFETs (VGS(TH) < 3V) should be used. Pay close attention to the BVDSS specification for the MOSFETs as well; most of the logic-level MOSFETs are limited to 30V or less. Selection criteria for the power MOSFETs include the onresistance, RDS(ON), Miller capacitance, CMILLER, input voltage and maximum output current. Miller capacitance, CMILLER, can be approximated from the gate charge curve usually provided on the MOSFET manufacturers' data sheet. CMILLER is equal to the increase in gate charge along the horizontal axis while the curve is approximately flat divided by the specified change in VDS. This result is then multiplied by the ratio of the application applied VDS to the gate charge curve specified VDS. When the IC is operating in continuous mode, the duty cycles for the top and bottom MOSFETs are given by: Main Switch Duty Cycle = VOUT VIN Synchronous Switch Duty Cycle = VIN - VOUT VIN The MOSFET power dissipations at maximum output current are given by: PMAIN = PSYNC = VOUT (IMAX )2 (1+ ) RDS(ON) + VIN I ( VIN )2 MAX (RDR ) (CMILLER ) * 2 1 1 (f) + VINTVCC - VTH(MIN) VTH(MIN) VIN - VOUT (IMAX )2 (1+ ) RDS(ON) VIN where is the temperature dependency of RDS(ON) and RDR (approximately 2) is the effective driver resistance at the MOSFET's Miller threshold voltage. VTH(MIN) is the typical MOSFET minimum threshold voltage. Both MOSFETs have I2R losses while the topside N-channel equation includes an additional term for transition losses, which are highest at high input voltages. For VIN < 20V, the high current efficiency generally improves with larger MOSFETs, while for VIN > 20V, the transition losses rapidly increase to the point that the use of a higher RDS(ON) device with lower CMILLER actually provides higher efficiency. The synchronous MOSFET losses are greatest at high input voltage when the top switch duty factor is low or during short-circuit when the synchronous switch is on close to 100% of the period. The term (1 + ) is generally given for a MOSFET in the form of a normalized RDS(ON) vs Temperature curve, but = 0.005/C can be used as an approximation for low voltage MOSFETs. The optional Schottky diode conducts during the dead time between the conduction of the two power MOSFETs. This prevents the body diode of the bottom MOSFET from turning on, storing charge during the dead time and requiring a reverse recovery period that could cost as much as 3% in efficiency at high VIN. A 1A to 3A Schottky is generally a good size due to the relatively small average current. Larger diodes result in additional transition losses due to their larger junction capacitance. Soft-Start and Tracking The LTC3851A has the ability to either soft-start by itself with a capacitor or track the output of another channel or external supply. When the LTC3851A is configured to soft-start by itself, a capacitor should be connected to the TK/SS pin. The LTC3851A is in the shutdown state if the RUN pin voltage is below 1.10V. TK/SS pin is actively pulled to ground in this shutdown state. Once the RUN pin voltage is above 1.22V, the LTC3851A powers up. A soft-start current of 1A then starts to charge its soft-start capacitor. Note that soft-start or tracking is achieved not by limiting the maximum output current of the controller but by controlling the output ramp voltage according to the ramp rate on the TK/SS pin. Current foldback is disabled during this phase to ensure smooth soft-start or tracking. The soft-start or tracking range is 3851afa 14 LTC3851A Applications Information 0V to 0.8V on the TK/SS pin. The total soft-start time can be calculated as: tSOFT-START = 0.8 * CSS 1.0A Regardless of the mode selected by the MODE/PLLIN pin, the regulator will always start in pulse-skipping mode up to TK/SS = 0.64V. Between TK/SS = 0.64V and 0.72V, it will operate in forced continuous mode and revert to the selected mode once TK/SS > 0.72V. The output ripple is minimized during the 80mV forced continuous mode window. When the regulator is configured to track another supply, the feedback voltage of the other supply is duplicated by a resistor divider and applied to the TK/SS pin. Therefore, the voltage ramp rate on this pin is determined by the ramp rate of the other supply's voltage. Note that the small soft-start capacitor charging current is always flowing, producing a small offset error. To minimize this error, one can select the tracking resistive divider value to be small enough to make this error negligible. In order to track down another supply after the soft-start phase expires, the LTC3851A must be configured for forced continuous operation by connecting MODE/PLLIN to INTVCC. Output Voltage Tracking The LTC3851A allows the user to program how its output ramps up and down by means of the TK/SS pins. Through this pin, the output can be set up to either coincidentally or ratiometrically track with another supply's output, as shown in Figure 3. In the following discussions, VMASTER refers to a master supply and VOUT refers to the LTC3851A's output as a slave supply. To implement the coincident tracking in Figure 3a, connect a resistor divider to VMASTER and connect its midpoint to the TK/SS pin of the LTC3851A. The ratio of this divider should be selected the same as that of the LTC3851A's feedback divider as shown in Figure 4a. In this tracking mode, VMASTER must be higher than VOUT. To implement ratiometric tracking, the ratio of the resistor divider connected to VMASTER is determined by: VOUT VMASTER = R2 R3 + R4 R4 R1+ R2 So which mode should be programmed? While either mode in Figure 4 satisfies most practical applications, the coincident mode offers better output regulation. This concept can be better understood with the help of Figure 5. At the input stage of the error amplifier, two common anode diodes are used to clamp the equivalent reference voltage and an additional diode is used to match the shifted common mode voltage. The top two current sources are of the same amplitude. In the coincident VOUT VMASTER OUTPUT VOLTAGE OUTPUT VOLTAGE VMASTER VOUT TIME TIME (3a) Coincident Tracking 3851A F03 (3b) Ratiometric Tracking Figure 3. Two Different Modes of Output Voltage Tracking 3851afa 15 LTC3851A Applications Information VMASTER VOUT R3 TO TK/SS PIN TO VFB PIN R4 R3 R4 VMASTER VOUT TO TK/SS PIN R1 R2 TO VFB PIN R3 R4 3851A F04 (4a) Coincident Tracking Setup (4b) Ratiometric Tracking Setup Figure 4. Setup for Coincident and Ratiometric Tracking I I + D1 D2 EA TK/SS 0.8V VFB - D3 3851A F05 Figure 5. Equivalent Input Circuit of Error Amplifier mode, the TK/SS voltage is substantially higher than 0.8V at steady state and effectively turns off D1. D2 and D3 will therefore conduct the same current and offer tight matching between VFB and the internal precision 0.8V reference. In the ratiometric mode, however, TK/SS equals 0.8V at steady state. D1 will divert part of the bias current to make VFB slightly lower than 0.8V. Although this error is minimized by the exponential I-V characteristic of the diode, it does impose a finite amount of output voltage deviation. Furthermore, when the master supply's output experiences dynamic excursion (under load transient, for example), the slave channel output will be affected as well. For better output regulation, use the coincident tracking mode instead of ratiometric. INTVCC Regulator The LTC3851A features a PMOS low dropout linear regulator (LDO) that supplies power to INTVCC from the VIN supply. INTVCC powers the gate drivers and much of the LTC3851A 's internal circuitry. The LDO regulates the voltage at the INTVCC pin to 5V. The LDO can supply a peak current of 50mA and must be bypassed to ground with a minimum of 2.2F ceramic capacitor or low ESR electrolytic capacitor. No matter what type of bulk capacitor is used, an additional 0.1F ceramic capacitor placed directly adjacent to the INTVCC and GND pins is highly recommended. Good bypassing is needed to supply the high transient currents required by the MOSFET gate drivers. High input voltage applications in which large MOSFETs are being driven at high frequencies may cause the maxi mum junction temperature rating for the LTC3851A to be exceeded. The INTVCC current, which is dominated by the gate charge current, is supplied by the 5V LDO. Power dissipation for the IC in this case is highest and is approximately equal to VIN * IINTVCC . The gate charge current is dependent on operating frequency as discussed in the Efficiency Considerations section. The junction temperature can be estimated by using the equations given in Note 3 of the Electrical Characteristics. For example, the LTC3851A INTVCC current is limited to less than 14mA from a 36V supply in the GN package: TJ = 70C + (14mA)(36V)(110C/W) = 125C To prevent the maximum junction temperature from being exceeded, the input supply current must be checked while operating in continuous conduction mode (MODE/PLLIN = INTVCC) at maximum VIN . Topside MOSFET Driver Supply (CB, DB) An external bootstrap capacitor, CB, connected to the BOOST pin supplies the gate drive voltage for the topside MOSFET. Capacitor CB in the Functional Diagram is charged though external diode DB from INTVCC when the SW pin is low. When the topside MOSFET is to be turned on, the driver places the CB voltage across the gate source of the MOSFET. This enhances the MOSFET and turns on the topside switch. The switch node voltage, SW, rises to VIN 3851afa 16 LTC3851A Applications Information and the BOOST pin follows. With the topside MOSFET on, the boost voltage is above the input supply: VBOOST = VIN + VINTVCC The value of the boost capacitor CB needs to be 100 times that of the total input capacitance of the topside MOSFET. The reverse breakdown of the external Schottky diode must be greater than VIN(MAX). Undervoltage Lockout The LTC3851A has two functions that help protect the controller in case of undervoltage conditions. A precision UVLO comparator constantly monitors the INTVCC voltage to ensure that an adequate gate-drive voltage is present. It locks out the switching action when INTVCC is below 3.2V. To prevent oscillation when there is a disturbance on the INTVCC, the UVLO comparator has 400mV of preci sion hysteresis. Another way to detect an undervoltage condition is to monitor the VIN supply. Because the RUN pin has a precision turn-on reference of 1.22V, one can use a resistor divider to VIN to turn on the IC when VIN is high enough. CIN Selection In continuous mode, the source current of the top Nchannel MOSFET is a square wave of duty cycle VOUT/ VIN . To prevent large voltage transients, a low ESR input capacitor sized for the maximum RMS current must be used. The maximum RMS capacitor current is given by: IRMS 1/ 2 VOUT VIN IO(MAX) - 1 VIN VOUT This formula has a maximum at VIN = 2VOUT, where IRMS = IO(MAX)/2. This simple worst-case condition is commonly used for design because even significant deviations do not offer much relief. Note that capacitor manufacturers' ripple current ratings are often based on only 2000 hours of life. This makes it advisable to further derate the capacitor or to choose a capacitor rated at a higher temperature than required. Several capacitors may also be paralleled to meet size or height requirements in the design. Always consult the manufacturer if there is any question. COUT Selection The selection of COUT is primarily determined by the effective series resistance, ESR, to minimize voltage ripple. The output ripple, VOUT, in continuous mode is determined by: 1 VOUT IL ESR + 8fCOUT where f = operating frequency, COUT = output capacitance and IL = ripple current in the inductor. The output ripple is highest at maximum input voltage since IL increases with input voltage. Typically, once the ESR requirement for COUT has been met, the RMS current rating generally far exceeds the IRIPPLE(P-P) requirement. With IL = 0.3IOUT(MAX) and allowing 2/3 of the ripple to be due to ESR, the output ripple will be less than 50mV at maximum VIN if the ILIM pin is configured to float and: COUT Required ESR < 2.2RSENSE COUT > 1 8fRSENSE The first condition relates to the ripple current into the ESR of the output capacitance while the second term guarantees that the output capacitance does not significantly discharge during the operating frequency period due to ripple current. The choice of using smaller output capacitance increases the ripple voltage due to the discharging term but can be compensated for by using capacitors of very low ESR to maintain the ripple voltage at or below 50mV. The ITH pin OPTI-LOOP compensation components can be optimized to provide stable, high performance transient response regardless of the output capacitors selected. The selection of output capacitors for applications with large load current transients is primarily determined by the voltage tolerance specifications of the load. The resistive component of the capacitor, ESR, multiplied by the load current change, plus any output voltage ripple must be within the voltage tolerance of the load. 3851afa 17 LTC3851A Applications Information The required ESR due to a load current step is: RESR V I where I is the change in current from full load to zero load (or minimum load) and V is the allowed voltage deviation (not including any droop due to finite capacitance). The amount of capacitance needed is determined by the maximum energy stored in the inductor. The capacitance must be sufficient to absorb the change in inductor current when a high current to low current transition occurs. The opposite load current transition is generally determined by the control loop OPTI-LOOP components, so make sure not to over compensate and slow down the response. The minimum capacitance to assure the inductors' energy is adequately absorbed is: COUT > L ( I) 2 2 ( V ) VOUT AVX TPSV or the KEMET T510 series of surface mount tantalums, available in case heights ranging from 1.5mm to 4.1mm. Aluminum electrolytic capacitors can be used in cost-driven applications, provided that consideration is given to ripple current ratings, temperature and long-term reliability. A typical application will require several to many aluminum electrolytic capacitors in parallel. A combination of the above mentioned capacitors will often result in maximizing performance and minimizing overall cost. Other capacitor types include Nichicon PL series, NEC Neocap, Panasonic SP and Sprague 595D series. Consult manufacturers for other specific recommendations. Like all components, capacitors are not ideal. Each ca pacitor has its own benefits and limitations. Combinations of different capacitor types have proven to be a very cost effective solution. Remember also to include high frequency decoupling capacitors. They should be placed as close as possible to the power pins of the load. Any inductance present in the circuit board traces negates their usefulness. where I is the change in load current. Setting Output Voltage Manufacturers such as Nichicon, United Chemi-Con and Sanyo can be considered for high performance throughhole capacitors. The OS-CON semiconductor electrolyte capacitor available from Sanyo has the lowest (ESR) (size) product of any aluminum electrolytic at a somewhat higher price. An additional ceramic capacitor in parallel with OS-CON capacitors is recommended to reduce the inductance effects. The LTC3851A output voltage is set by an external feedback resistive divider carefully placed across the output, as shown in Figure 6. The regulated output voltage is determined by: In surface mount applications, ESR, RMS current handling and load step specifications may require multiple capacitors in parallel. Aluminum electrolytic, dry tantalum and special polymer capacitors are available in surface mount packages. Special polymer surface mount capacitors offer very low ESR but have much lower capacitive density per unit volume than other capacitor types. These capacitors offer a very cost-effective output capacitor solution and are an ideal choice when combined with a controller having high loop bandwidth. Tantalum capacitors offer the highest capacitance density and are often used as output capacitors for switching regulators having controlled soft-start. Several excellent surge-tested choices are the AVX TPS, IL(SC) = tON(MIN) * VIN L To improve the transient response, a feed-forward ca pacitor, CFF , may be used. Great care should be taken to route the VFB line away from noise sources, such as the inductor or the SW line. VOUT LTC3851A RB CFF VFB RA 3851A F06 Figure 6. Settling Output Voltage 3851afa 18 LTC3851A Applications Information Fault Conditions: Current Limit and Current Foldback Phase-Locked Loop and Frequency Synchronization The LTC3851A includes current foldback to help limit load current when the output is shorted to ground. If the output falls below 40% of its nominal output level, the maximum sense voltage is progressively lowered from its maximum programmed value to about 25% of the that value. Foldback current limiting is disabled during softstart or tracking. Under short-circuit conditions with very low duty cycles, the LTC3851A will begin cycle skipping in order to limit the short-circuit current. In this situation the bottom MOSFET will be dissipating most of the power but less than in normal operation. The short-circuit ripple current is determined by the minimum on-time tON(MIN) of the LTC3851A (90ns), the input voltage and inductor value: The LTC3851A has a phase-locked loop (PLL) comprised of an internal voltage-controlled oscillator (VCO) and a phase detector. This allows the turn-on of the top MOSFET to be locked to the rising edge of an external clock signal applied to the MODE/PLLIN pin. This phase detector is an edge sensitive digital type that provides zero degrees phase shift between the external and internal oscillators. This type of phase detector does not exhibit false lock to harmonics of the external clock. R VOUT = 0.8V 1+ B RA The resulting short-circuit current is: ISC = 1/4MaxVSENSE 1 - IL(SC) 2 RSENSE Programming Switching Frequency To set the switching frequency of the LTC3851A, connect a resistor, RFREQ, between FREQ/PLLFLTR and GND. The relationship between the oscillator frequency and RFREQ is shown in Figure 7. A 0.1F bypass capacitor should be connected in parallel with RFREQ . 750 The output of the phase detector is a pair of complemen tary current sources that charge or discharge the external filter network connected to the FREQ/PLLFLTR pin. Note that the LTC3851A can only be synchronized to an external clock whose frequency is within range of the LTC3851A's internal VCO.This is guaranteed to be between 250kHz and 750kHz. A simplified block diagram is shown in Figure 8. If the external clock frequency is greater than the internal oscillator's frequency, fOSC , then current is sunk con tinuously from the phase detector output, pulling down the FREQ/PLLFLTR pin. When the external clock frequency is less than fOSC, current is sourced continuously, pulling up the FREQ/PLLFLTR pin. If the external and internal frequencies are the same but exhibit a phase difference, the current sources turn on for an amount of time corresponding to the phase difference. The voltage on the FREQ/ PLLFLTR pin is adjusted until the phase and frequency of the internal and external oscillators are identical. At the stable operating point, the phase detector output is high impedance and the filter capacitor CLP holds the voltage. OSCILLATOR FREQUENCY (kHz) 700 2.7V 650 RLP 600 CLP 550 500 450 EXTERNAL OSCILLATOR 400 350 MODE/ PLLIN FREQ/PLLFLTR DIGITAL PHASE/ FREQUENCY DETECTOR VCO 300 250 20 40 60 80 100 RFREQ (k) 120 140 160 3851 F07 Figure 7. Relationship Between Oscillator Frequency and Resistor Connected Between FREQ/PLLFLTR and GND 3851A F08 Figure 8. Phase-Locked Loop Block Diagram 3851afa 19 LTC3851A Applications Information The loop filter components, CLP and RLP, smooth out the current pulses from the phase detector and provide a stable input to the voltage-controlled oscillator. The filter components CLP and RLP determine how fast the loop acquires lock. Typically RLP is 1k to 10k and CLP is 2200pF to 0.01F. When the external oscillator is active before the LTC3851A is enabled, the internal oscillator frequency will track the external oscillator frequency as described in the preceding paragraphs. In situations where the LTC3851A is enabled before the external oscillator is active, a low free-running oscillator frequency of approximately 50kHz will result. It is possible to increase the free-running, pre-synchronization frequency by adding a second resistor, RFREQ, in parallel with RLP and CLP. RFREQ will also cause a phase difference between the internal and external oscillator signals. The magnitude of the phase difference is inversely proportional to the value of RFREQ. The free-running frequency may be programmed by using Figure 7 to determine the appropriate value of RFREQ. In order to maintain adequate phase margin for the PLL, the typical value for CLP is 0.01F and for RLP is 1k. The external clock (on MODE/PLLIN pin) input high threshold is nominally 1.6V, while the input low threshold is nominally 1.2V. Minimum On-Time Considerations Minimum on-time, tON(MIN), is the smallest time duration that the LTC3851A is capable of turning on the top MOSFET. It is determined by internal timing delays and the gate charge required to turn on the top MOSFET. Low duty cycle applications may approach this minimum on-time limit and care should be taken to ensure that: tON(MIN) < VOUT VIN (f) If the duty cycle falls below what can be accommodated by the minimum on-time, the controller will begin to skip cycles. The output voltage will continue to be regulated, but the ripple voltage and current will increase. The minimum on-time for the LTC3851A is approximately 90ns. However, as the peak sense voltage decreases the minimum on-time gradually increases. This is of particu lar concern in forced continuous applications with low ripple current at light loads. If the duty cycle drops below the minimum on-time limit in this situation, a significant amount of cycle skipping can occur with correspondingly larger current and voltage ripple. Efficiency Considerations The percent efficiency of a switching regulator is equal to the output power divided by the input power times 100%. It is often useful to analyze individual losses to determine what is limiting the efficiency and which change would produce the most improvement. Percent efficiency can be expressed as: %Efficiency = 100% - (L1 + L2 + L3 + ...) where L1, L2, etc. are the individual losses as a percent age of input power. Although all dissipative elements in the circuit produce losses, four main sources usually account for most of the losses in LTC3851A circuits: 1) IC VIN current, 2) INTVCC regulator current, 3) I2R losses, 4) topside MOSFET transition losses. 1. The VIN current is the DC supply current given in the Electrical Characteristics table, which excludes MOSFET driver current. VIN current typically results in a small (<0.1%) loss. 2. INTVCC current is the sum of the MOSFET driver and control currents. The MOSFET driver current results from switching the gate capacitance of the power MOSFETs. Each time a MOSFET gate is switched from low to high to low again, a packet of charge dQ moves from INTVCC to ground. The resulting dQ/dt is a current out of INTVCC that is typically much larger than the control circuit current. In continuous mode, IGATECHG = f(QT + QB), where QT and QB are the gate charges of the topside and bottom side MOSFETs. 3851afa 20 LTC3851A Applications Information 3. I2R losses are predicted from the DC resistances of the fuse (if used), MOSFET, inductor and current sense resistor. In continuous mode, the average output current flows through L and RSENSE, but is chopped between the topside MOSFET and the synchronous MOSFET. If the two MOSFETs have approximately the same RDS(ON), then the resistance of one MOSFET can simply be summed with the resistances of L and RSENSE to obtain I2R losses. For example, if each RDS(ON) = 10m, DCR = 10m and RSENSE = 5m, then the total resistance is 25m. This results in losses ranging from 2% to 8% as the output current increases from 3A to 15A for a 5V output, or a 3% to 12% loss for a 3.3V output. Efficiency varies as the inverse square of VOUT for the same external components and output power level. The combined effects of increasingly lower output voltages and higher currents required by high performance digital systems is not doubling but quadrupling the importance of loss terms in the switching regulator system! 4. Transition losses apply only to the topside MOSFET(s), and become significant only when operating at high input voltages (typically 15V or greater). Transition losses can be estimated from: Transition Loss = (1.7)VIN2 * IO(MAX) * CRSS * f Other hidden losses such as copper trace and the battery internal resistance can account for an additional 5% to 10% efficiency degradation in portable systems. It is very important to include these system level losses during the design phase. The internal battery and fuse resistance losses can be minimized by making sure that CIN has adequate charge storage and very low ESR at the switching frequency. A 25W supply will typically require a minimum of 20F to 40F of capacitance having a maximum of 20m to 50m of ESR. Other losses including Schottky conduction losses during dead time and inductor core losses generally account for less than 2% total additional loss. Checking Transient Response The regulator loop response can be checked by looking at the load current transient response. Switching regulators take several cycles to respond to a step in DC (resistive) load current. When a load step occurs, VOUT shifts by an amount equal to ILOAD (ESR), where ESR is the effective series resistance of COUT. ILOAD also begins to charge or discharge COUT generating the feedback error signal that forces the regulator to adapt to the current change and return VOUT to its steady-state value. During this recovery time VOUT can be monitored for excessive overshoot or ringing, which would indicate a stability problem. The availability of the ITH pin not only allows optimization of control loop behavior but also provides a DC coupled and AC filtered closed-loop response test point. The DC step, rise time and settling at this test point truly reflects the closed-loop response. Assuming a predominantly second order system, phase margin and/or damping factor can be estimated using the percentage of overshoot seen at this pin. The bandwidth can also be estimated by examining the rise time at the pin. The ITH external components shown in the Typical Application circuit will provide an adequate starting point for most applications. The ITH series RC-CC filter sets the dominant pole-zero loop compensation. The values can be modified slightly (from 0.5 to 2 times their suggested values) to optimize transient response once the final PC layout is done and the particular output capacitor type and value have been determined. The output capacitors need to be selected because the various types and values determine the loop gain and phase. An output current pulse of 20% to 80% of full-load current having a rise time of 1s to 10s will produce output voltage and ITH pin waveforms that will give a sense of the overall loop stability without break ing the feedback loop. Placing a power MOSFET directly across the output capacitor and driving the gate with an appropriate signal generator is a practical way to produce a realistic load step condition. The initial output voltage step resulting from the step change in output current may not be within the bandwidth of the feedback loop, so this signal cannot be used to determine phase margin. This is why it is better to look at the ITH pin signal which is in the feedback loop and is the filtered and compensated control loop response. The midband gain of the loop will be in creased by increasing RC and the bandwidth of the loop will be increased by decreasing CC. If RC is increased by the same factor that CC is decreased, the zero frequency will be kept the same, thereby keeping the phase shift the same in the most critical frequency range of the feedback loop. The output voltage settling behavior is related to the 3851afa 21 LTC3851A Applications Information PC Board Layout Checklist stability of the closed-loop system and will demonstrate the actual overall supply performance. When laying out the printed circuit board, the following checklist should be used to ensure proper operation of the LTC3851A. These items are also illustrated graphically in the layout diagram of Figure 9. Check the following in your layout: A second, more severe transient is caused by switching in loads with large (>1F) supply bypass capacitors. The discharged bypass capacitors are effectively put in parallel with COUT, causing a rapid drop in VOUT. No regulator can alter its delivery of current quickly enough to prevent this sudden step change in output voltage if the load switch resistance is low and it is driven quickly. If the ratio of CLOAD to COUT is greater than 1:50, the switch rise time should be controlled so that the load rise time is limited to approximately 25 * CLOAD. Thus a 10F capacitor would require a 250s rise time, limiting the charging current to about 200mA. 1. Are the board signal and power grounds segregated? The LTC3851A GND pin should tie to the ground plane close to the input capacitor(s). The low current or signal ground lines should make a single point tie directly to the GND pin. The synchronous MOSFET source pins should connect to the input capacitor(s) ground. + 1 RFREQ 2 3 CSS RC 4 CC CC2 47pF 5 6 1000pF 10 MODE/PLLIN SW FREQ/PLLFLTR TG RUN BOOST LTC3851A TK/SS VIN ITH INTVCC VFB BG 7 SENSE- GND 8 SENSE+ ILIM 16 15 M1 CIN + 0.1F CB 14 VIN 13 DB 12 11 + M2 4.7F 10 - 9 L1 10 - R1 + R2 COUT VOUT RSENSE 3851A F09 + Figure 9. LTC3851A Layout Diagram 3851afa 22 LTC3851A Applications Information 2. Does the VFB pin connect directly to the feedback resistors? The resistive divider R1, R2 must be connected between the (+) plate of COUT and signal ground. The 47pF to 100pF capacitor should be as close as possible to the LTC3851A. Be careful locating the feedback resistors too far away from the LTC3851A. The VFB line should not be routed close to any other nodes with high slew rates. 3. Are the SENSE- and SENSE+ leads routed together with minimum PC trace spacing? The filter capacitor between SENSE+ and SENSE- should be as close as possible to the LTC3851A. Ensure accurate current sensing with Kelvin connections as shown in Figure 10. Series resistance can be added to the SENSE lines to increase noise rejection and to compensate for the ESL of RSENSE. 4. Does the (+) terminal of CIN connect to the drain of the topside MOSFET(s) as closely as possible? This capacitor provides the AC current to the MOSFET(s). 5. Is the INTVCC decoupling capacitor connected closely between INTVCC and GND? This capacitor carries the MOSFET driver peak currents. An additional 1F ceramic capacitor placed immediately next to the INTVCC and GND pins can help improve noise performance. 6. Keep the switching node (SW), top gate node (TG) and boost node (BOOST) away from sensitive small-signal nodes, especially from the voltage and current sensing feedback pins. All of these nodes have very large and fast moving signals and therefore should be kept on the output side (Pin 9 to Pin 16) of the LTC3851AEGN and occupy minimum PC trace area. HIGH CURRENT PATH 3851A F10 SENSE+ SENSE- CURRENT SENSE RESISTOR (RSENSE) PC Board Layout Debugging It is helpful to use a DC-50MHz current probe to monitor the current in the inductor while testing the circuit. Monitor the output switching node (SW pin) to synchronize the oscilloscope to the internal oscillator and probe the actual output voltage as well. Check for proper performance over the operating voltage and current range expected in the application. The frequency of operation should be maintained over the input voltage range down to dropout and until the output load drops below the low current operation threshold--typically 10% of the maximum designed current level in Burst Mode operation. The duty cycle percentage should be maintained from cycle to cycle in a well designed, low noise PCB imple mentation. Variation in the duty cycle at a subharmonic rate can suggest noise pick-up at the current or voltage sensing inputs or inadequate loop compensation. Over compensation of the loop can be used to tame a poor PC layout if regulator bandwidth optimization is not required. Reduce VIN from its nominal level to verify operation of the regulator in dropout. Check the operation of the undervoltage lockout circuit by further lowering VIN while monitoring the outputs to verify operation. Investigate whether any problems exist only at higher out put currents or only at higher input voltages. If problems coincide with high input voltages and low output currents, look for capacitive coupling between the BOOST, SW, TG and possibly BG connections and the sensitive voltage and current pins. The capacitor placed across the current sensing pins needs to be placed immediately adjacent to the pins of the IC. This capacitor helps to minimize the effects of differential noise injection due to high frequency capacitive coupling. If problems are encountered with high current output loading at lower input voltages, look for inductive coupling between CIN, the Schottky and the top MOSFET to the sensitive current and voltage sensing traces. In addition, investigate common ground path voltage pickup between these components and the GND pin of the IC. Figure 10. Kelvin Sensing RSENSE 3851afa 23 LTC3851A Applications Information Design Example As a design example, assume VIN = 12V (nominal), VIN = 22V (maximum), VOUT = 1.8V, IMAX = 5A, and f = 250kHz. Refer to Figure 13. The inductance value is chosen first based on a 30% ripple current assumption. The highest value of ripple current occurs at the maximum input voltage. Connect a 160k resistor between the FREQ/PLLFLTR and GND pins, generating 250kHz operation. The minimum inductance for 30% ripple current is: IL = V 1 VOUT 1- OUT VIN ( f) (L) A 4.7H inductor will produce 28% ripple current and a 3.3H will result in 40%. The peak inductor current will be the maximum DC value plus one-half the ripple current, or 6A, for the 3.3H value. Increasing the ripple current will also help ensure that the minimum on-time of 90ns is not violated. The minimum on-time occurs at maximum VIN: tON(MIN) = VOUT VIN(MAX) ( f) = 1.8V = 327ns 22V (250kHz ) The RSENSE resistor value can be calculated by connecting ILIM to INTVCC and using the maximum current sense voltage specification with some accommodation for tolerances. Tie ILIM to INTVCC. RSENSE 75mV = 0.0125, so 0.01 is selected 6A Choosing 1% resistors: R1 = 25.5k and R2 = 32.4k yields an output voltage of 1.816V. The power dissipation on the topside MOSFET can be easily estimated. Choosing a Fairchild FDS6982S dual MOSFET results in: RDS(ON) = 0.035/0.022, CMILLER = 215pF. At maximum input voltage with T (estimated) = 50C: PMAIN = 1.8V 2 (5) 1+ (0.005) (50C - 25C) * 22V 5A (0.035) + (22V )2 (2) (215pF ) * 2 1 1 + (250kHz ) = 185mW 5 - 2.3 2.3 A short circuit to ground will result in a folded back current of: ISC = 29mV 1 90ns (22V ) - = 2.02A 0.0125 2 3.3H with a typical value of RDS(ON) and = (0.005/C)(25C) = 0.125. The resulting power dissipated in the bottom MOSFET is: 22V (2.02A )2 (1.125) (0.022) 22V = 101.0mW PSYNC = which is less than under full-load conditions. CIN is chosen for an RMS current rating of at least 3A at temperature. COUT is chosen with an ESR of 0.02 for low output ripple. The output ripple in continuous mode will be highest at the maximum input voltage. The output voltage ripple due to ESR is approximately: VORIPPLE = RESR (IL) = 0.02 (2A) = 40mVP-P 3851afa 24 LTC3851A Typical Applications VIN 4.5V TO 32V MODE/PLLIN RFREQ 82.5k C20 0.1F VIN FREQ/PLLFLTR CSS 0.1F RUN TG M1 HAT2170H CB 0.1F BOOST ITH INTVCC DB CMDSH05-4 4.7F VFB 30.1k VOUT 3.3V 15A SW CC2 330pF C5 0.047F CIN 22F L1 0.68H LTC3851A TK/SS CC RC 2200pF 15k + GND SENSE+ ILIM C15 47pF M2 HAT2170H BG SENSE- R27 3.01k R2 154k 1% R1 48.7k 1% + COUT 330F x2 COUT: SANYO 6TPE330MIL CIN: SANYO 63HVH22M L1: VISHAY IHLP5050-EZERR68MO1 3851A F11 Figure 11. High Efficiency 3.3V/15A Step-Down Converter C2 0.01F R5 1k PLLIN 350kHz VIN 6V TO 14V MODE/PLLIN VIN FREQ/PLLFLTR CSS 0.1F C1 1000pF RUN CC2 100pF CB 0.1F BOOST ITH SW CIN 180F RSENSE 0.002 DB CMDSH-3 C10 33pF INTVCC 4.7F VFB M1 RJK0305DPB L1 0.68H LTC3851A TK/SS CC RC 1000pF 7.5k TG + BG SENSE- GND SENSE+ ILIM M2 RJK0301DPB R2 43.2k 1% R1 20k 1% VOUT 1.5V 15A + COUT 330F x2 1000pF R22 10 COUT: SANYO 2R5TPE330M9 L1: SUMIDA CEP125-OR6MC R20 10 3851A F12 Figure 12. 1.5V/15A Synchronized at 350kHz 3851afa 25 LTC3851A package description GN Package 16-Lead Plastic SSOP (Narrow .150 Inch) (Reference LTC DWG # 05-08-1641) .189 - .196* (4.801 - 4.978) .045 .005 16 15 14 13 12 11 10 9 .254 MIN .009 (0.229) REF .150 - .165 .229 - .244 (5.817 - 6.198) .0165 .0015 .150 - .157** (3.810 - 3.988) .0250 BSC RECOMMENDED SOLDER PAD LAYOUT 1 .015 .004 x 45 (0.38 0.10) .007 - .0098 (0.178 - 0.249) .0532 - .0688 (1.35 - 1.75) 2 3 4 5 6 7 8 .004 - .0098 (0.102 - 0.249) 0 - 8 TYP .016 - .050 (0.406 - 1.270) NOTE: 1. CONTROLLING DIMENSION: INCHES INCHES 2. DIMENSIONS ARE IN (MILLIMETERS) .008 - .012 (0.203 - 0.305) TYP .0250 (0.635) BSC GN16 (SSOP) 0204 3. DRAWING NOT TO SCALE *DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE **DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE 3851afa 26 LTC3851A Package Description UD Package 16-Lead Plastic QFN (3mm x 3mm) (Reference LTC DWG # 05-08-1691) 0.70 0.05 3.50 0.05 1.45 0.05 2.10 0.05 (4 SIDES) PACKAGE OUTLINE 0.25 0.05 0.50 BSC RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS 3.00 0.10 (4 SIDES) BOTTOM VIEW--EXPOSED PAD PIN 1 NOTCH R = 0.20 TYP OR 0.25 x 45 CHAMFER R = 0.115 TYP 0.75 0.05 15 PIN 1 TOP MARK (NOTE 6) 16 0.40 0.10 1 1.45 0.10 (4-SIDES) 2 (UD16) QFN 0904 0.200 REF 0.00 - 0.05 NOTE: 1. DRAWING CONFORMS TO JEDEC PACKAGE OUTLINE MO-220 VARIATION (WEED-2) 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 0.25 0.05 0.50 BSC 3851afa 27 LTC3851A Package Description MSE Package 16-Lead Plastic MSOP, Exposed Die Pad (Reference LTC DWG # 05-08-1667 Rev C) BOTTOM VIEW OF EXPOSED PAD OPTION 2.845 0.102 (.112 .004) 5.23 (.206) MIN 2.845 0.102 (.112 .004) 0.889 0.127 (.035 .005) 8 1 1.651 0.102 (.065 .004) 1.651 0.102 3.20 - 3.45 (.065 .004) (.126 - .136) 0.305 0.038 (.0120 .0015) TYP 16 0.50 (.0197) BSC 4.039 0.102 (.159 .004) (NOTE 3) RECOMMENDED SOLDER PAD LAYOUT 0.254 (.010) 0.35 REF 0.12 REF DETAIL "B" CORNER TAIL IS PART OF DETAIL "B" THE LEADFRAME FEATURE. FOR REFERENCE ONLY 9 NO MEASUREMENT PURPOSE 0.280 0.076 (.011 .003) REF 16151413121110 9 DETAIL "A" 0 - 6 TYP 3.00 0.102 (.118 .004) (NOTE 4) 4.90 0.152 (.193 .006) GAUGE PLANE 0.53 0.152 (.021 .006) DETAIL "A" 1.10 (.043) MAX 0.18 (.007) SEATING PLANE 0.17 - 0.27 (.007 - .011) TYP 1234567 8 0.50 (.0197) BSC NOTE: 1. DIMENSIONS IN MILLIMETER/(INCH) 2. DRAWING NOT TO SCALE 3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX 0.86 (.034) REF 0.1016 0.0508 (.004 .002) MSOP (MSE16) 0910 REV C 3851afa 28 LTC3851A Revision History REV DATE DESCRIPTION A 6/11 Added H-Grade and MP-Grade parts. Reflected throughout the data sheet. PAGE NUMBER 1-30 3851afa Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 29 LTC3851A Typical Application RFREQ 160k 0.1F CSS 0.1F VIN 4.5V TO 22V MODE/PLLIN VIN FREQ/PLLFLTR TG RUN CC2 220pF CB 0.1F M1A FDS6982S BOOST SW ITH INTVCC VFB BG GND SENSE+ ILIM RSENSE 0.01 DB CMDSH-3 4.7F SENSE- CIN 22F 25V L1 3.3H LTC3851A TK/SS CC RC 470pF 33k + VOUT 1.8V 5A R2 32.4k 1% M1B FDS6982S + R1 25.5k 1% COUT 150F 6.3V x2 PANASONIC SP 1000pF 10 10 COUT: PANASONIC EEFUEOG151R CIN: MARCON THCR70LE1H226ZT L1: PANASONIC ETQP6F3R3HFA RSENSE: IRC LR 2010-01-R010F 3851A F13 Figure 13. 1.8V/5A Converter from Design Example with Pulse-Skipping Operation Related Parts PART NUMBER DESCRIPTION COMMENTS LTC3854 Small Footprint Wide VIN Range Synchronous Step-Down DC/ DC Controller Fixed 400kHz Operating Frequency, 4.5V VIN 38V, 0.8V VOUT 5.25V, 2mm x 3mm QFN-12 LTC3878 No RSENSETM Constant On-Time Synchronous Step-Down DC/ DC Controller Very Fast Transient Response, tON(MIN) = 43ns, 4V VIN 38V, 0.8V VOUT 0.9VIN, SSOP-16 LTC3879 No RSENSE Constant On-Time Synchronous Step-Down DC/DC Controller Very Fast Transient Response, tON(MIN) = 43ns, 4V VIN 38V, 0.6V VOUT 0.9VIN, MSOP-16E, 3mm x 3mm QFN-16 LTC3850/LTC3850-1 Dual 2-Phase, High Efficiency Synchronous Step-Down DC/DC LTC3850-2 Controllers, RSENSE or DCR Current Sensing and Tracking Phase-Lockable Fixed Operating Frequency 250kHz to 780kHz, 4V VIN 30V, 0.8V VOUT 5.25V LTC3853 Triple Output, Multiphase Synchronous Step-Down DC/DC Controller, RSENSE or DCR Current Sensing and Tracking Phase-Lockable Fixed Operating Frequency 250kHz to 750kHz, 4V VIN 24V, VOUT Up to 13.5V LTC3610 12A, 1MHz, Monolithic Synchronous Step-Down DC/DC Converter High Efficiency, Adjustable Constant On-Time, 4V VIN 24V, VOUT(MIN) = 0.6V, 9mm x 9mm QFN-64 LTC3611 10A, 1MHz, Monolithic Synchronous Step-Down DC/DC Converter High Efficiency, Adjustable Constant On-Time, 4V VIN 32V, VOUT(MIN) = 0.6V, 9mm x 9mm QFN-64 LTC3775 High Frequency Synchronous Voltage Mode Step-Down DC/DC Synchronizable Fixed Frequency 250kHz to 1MHz, Controller tON(MIN) = 30ns, 4V VIN 38V, 0.6V VOUT 0.8VIN, MSOP-16E, 3mm x 3mm QFN-16 3851afa 30 Linear Technology Corporation LT 0611 REV A * PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 www.linear.com LINEAR TECHNOLOGY CORPORATION 2010