Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P25E3.pdf 01.10.17 CERAFILr(Filters/Traps/Discriminators) for TV/VCR CERAFILr (FILTERS/TRAPS /DISCRIMINATORS) FOR TV/VCR Murata Manufacturing Co., Ltd. Cat.No.P25E-3 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. CONTENTS 1 CERAFILr in this catalog are the trademarks of Murata Manufacturing Co., Ltd. Part Numbering 1 P25E3.pdf 01.10.17 CERAFILr Chip Type SFSKA Series CERAFILr Chip Type Notice 2 4 5 2 CERAFILr Picture Band Low-Suprious SFSRA Series 3 CERAFILr Low-profile SFSRL Series 11 4 CERAFILr High-selectivity Type SFTRD Series 14 5 CERAFILr Chroma Signal SFSRA/H/L Series 17 CERAFILr Lead Type Notice 3 6 4 5 19 6 Ceramic Traps Chip Type TPSKA Series 20 7 Double Trap Chip Type TPWKA Series 21 Ceramic Trap Chip Type Notice 2 22 8 Ceramic Traps Three-terminals TPSRA Series 23 9 Ceramic Traps Two-terminals TPSRD Series 26 10 Ceramic Traps TPSRD Series for 2ch Sound TV in Germany 29 11 Double Traps TPWRD Series 30 12 Triple Traps TPTRD Series 32 Ceramic Trap Lead Type Notice 33 13 Discriminators Wide-Band Type CDSRH Series 34 14 Discriminators Low-Profile Type CDSRL Series 36 Ceramic Discriminator Notice 38 Chip Type Packaging 39 Lead Type Packaging 40 6 7 8 9 10 11 12 13 14 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. o Part Numbering P25E3.pdf 01.10.17 structure of the "Global Part Numbers" that have been adopted since June 2001 and the meaning of each code are described herein. ( The ) If you have any questions about details, inquire at your usual Murata sales office or distributor. CERAFILr for TV/VCR (Global Part Number) SF S RA 4M50 CF 00 -B0 q w e r t y u qProduct ID tProduct Specification Code (1) Product ID SF Ceramic Filters wOscillation/Numbers of Element Code Oscillation/Numbers of Element S 2 Elements Thickness Shear mode T 3 Elements Thickness Expander mode Code Product Specification Code (1) AF Standard Bandwidth Type BF Tight Bandwidth Type CF Standard Bandwidth Type DF Broad Bandwidth Type EF Ultra-broad Bandwidth Type The code AF is only applied to SFT series. yProduct Specification Code (2) eStructure/Size Code Structure/Size Code Product Specification Code (2) Rp Lead Type 00 Standard Type Kp Chip Type p is expressed "A" or subsequent code, which indicates the size. uPackaging Packaging Code rNominal Center Frequency -B0 Bulk Expressed by four-digit alphanumerics. The unit is in hertz (MHz). Decimal point is expressed by capital letter "M". -A0 Radial Taping H0=18mm -R1 Plastic Taping o=330mm Radial taping is applied to lead type and plastic taping to chip type. With non-standard products, two-digit alphanumerics indicating "Individual Specification" is added between "tProduct Specification Code (1)" and "yProduct Specification Code (2)". Ceramic Traps (Global Part Number) TP S RA 4M50 q w e r 00 -B0 t y B u qProduct ID tProduct Specification Code (1) Product ID TP Ceramic Traps Code Product Specification (1) B Broad-bandwidth Type C Low-capacitance Type wFunction yProduct Specification Code (2) Code Function S Single Traps Code Product Specification Code (2) T Triple Traps 00 Standard Type W Double Traps uPackaging eStructure/Size Code Code Structure/Size -B0 Bulk Rp Lead Type -A0 Radial Taping H0=18mm Kp Chip Type -R1 Plastic Taping o=330mm p is expressed "A" or subsequent code, which indicates the size. rNominal Center Frequency Expressed by four-digit alphanumerics. The unit is in hertz (MHz). Decimal point is expressed by capital letter "M". 2 Packaging Radial taping is applied to lead type and plastic taping to chip type. With non-standard products, three-digit alphanumerics indicating "Individual Specification" is added between "yProduct Specification Code (2)" and "uPackaging". Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P25E3.pdf 01.10.17 Discriminators for TV/VCR (Global Part Number) CD S RH 4M50 q w e r E K t y 048 -A0 u i yProduct Specification Code (2) qProduct ID Product ID CD Discriminators wOscillation Code Product Specification Code (2) K Specification uIC Code Oscillation Code IC S Thickness Shear mode 048 Applicable IC control code eStructure/Size iPackaging Code Structure/Size Code RH Standard Type -B0 Bulk RL Low-profile -A0 Radial Taping H0=18mm Packaging With non-standard products, an alphabet Indicating "Individual Specification" is added between "uIC" and "iPackaging". rNominal Center Frequency Expressed by four-digit alphanumerics. The unit is in hertz (MHz). Decimal point is expressed by capital letter "M". tProduct Specification Code (1) Code Product Specification Code (1) C Three-terminals E Two-terminals 3 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P25E3.pdf 01.10.17 CERAFILr(Filters/Traps/Discriminators) for TV/VCR 1 CERAFILr Chip Type SFSKA Series SMD ceramic filter SFSKA_CF is a small and thin SMD filter sealed with a metal cap. Recommended for LCD-TVs, and small and thin tuners. 7.90.2 3.00.1 1.80.2 Features 0.50.1 8.50.2 1. High attenuation outside bandwidth. 2. Small and thin pakage. 3. Reflow-solderable. 0.60.2 1.30.2 0.30.1 1.30.2 (1) 3.80.2 1.00.1 (2) (3) : Vender's Code : EIAJ monthly Code (1) : Input (2) : Ground (3) : Output Electrode in mm 2.50.2 2.50.2 Part Number Nominal Center Frequency (fn) (MHz) 3dB Bandwidth (kHz) 20dB Bandwidth (kHz) Insertion Loss (dB) Spurious Attenuation(1) (dB) Spurious Attenuation(2) (dB) Input/Output Impedance (ohm) SFSKA4M50CF00-R1 4.500 fn60 min. 600 max. 6.0 max. 20 min. [within 0 to fn] 15 min. [within fn to 7.0MHz] 1000 Spurious Response 0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) Frequency Characteristics 30 40 50 60 30 40 50 60 70 70 3.5 3.7 3.9 4.1 4.3 4.5 4.7 4.9 5.1 5.3 5.5 0.0 2.0 4.0 6.0 8.0 Frequency (MHz) Frequency (MHz) Test Circuit Standard Land Pattern Dimensions (1) (2) (3) (1) Input (2) Ground (3) Output 1.0 1.0 1.5 1.0 1.5 R1 E1 R2 C2 E2 RF Voltmeter 4.8 Rg S.S.G. R1+Rg=R2=1000 5%, Rg=50 C2=10pF (Including stray capacitance and Input capacitance of RF Voltmeter) E1:S.S.G. Output voltage 4 (in mm) 10.0 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P25E3.pdf 01.10.17 CERAFILr Chip Type Notice 1 Notice (Soldering and Mounting) 1. Standard Reflow Soldering Condition (1) Reflow Filter is soldered one time within the following temperature condition and then being placed in natural condition for 4 hours. 5 sec. 240 (2) Soldering Iron Lead terminal is directly contacted with the tip of soldering iron of 2805C for 3.0 seconds 0.5 seconds, and then being placed in natural condition for 4 hours. Temperature (C) 230 Gradual Cooling 150 2. Wash The component cannot be withstand washing. 60 30 Time (sec.) Notice (Handling) 1. The component may be damaged if excess mechanical stress is applied to it mounted on the printed circuit board. 2. Design layout of components on the PC board to minimize the stress imposed on the wrap or flexure of the board. 3. After installing chips, if solder is excessively applied to the circuit board, mechanical stress will cause destruction resistance characteristics to lower. To prevent this, be extremly careful in determining shape and dimension before designing the circuit board diagram. 4. When the positioning claws and pick up nozzle are worn, the load is applied to the chip while positioning is concentrated to one positioning accuracy, etc. Careful checking and maintenance are necessary to prevent unexpected trouble. 5. When correcting chips with a soldering iron, the tip of the soldering iron should not directly touch the chip component. 6. Cleaning or washing of the component is not acceptable due to non sealed construction. 7. In case of covering filter with over coat, conditions such as material of resin, cure temperature, and so on should be evaluated well. 8. Accurate test circuit values are required to measure electrical characteristics. It may be a cause of misscorrelation if there is any deviation, especially stray capacitance, from the test circuit in the specification. [Component direction] Put the component lateral to the direction in which stress acts. [Component layout close to board] Perforation A Susceptibility to stress is in the order of;A>C>B B Slit C 5 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P25E3.pdf 01.10.17 CERAFILr(Filters/Traps/Discriminators) for TV/VCR CERAFILr Picture Band Low-Suprious SFSRA Series 2 Features 0.9 (Ref.) 2.50.2 2.50.2 4.0 max. 0.480.1 7.0 (Ref.) 3.50.5 M 7.0 max. 10.0 max. As part of the environment protection activity, solder for terminal plating and terminal-element connection inside of ceramic filter SFSRA series contain no lead(Pb). This series also features thickness shear vibration mode same as SFSRH series(current type), which provides very low spurious response within video signal band. (3) (2) (1) 3--0.8 (in mm) 1. Excellent spurious suppression characteristics within video signal band. 2. Available 4 pass bandwidth variation to meet various requests. 3. Low profile (H=7.0mm max.) 4. Lead dimension : Improved mounting reliability (cut & clinch) due to round terminal. 6 Part Number Nominal Center Frequency (fn) (MHz) 3dB Bandwidth (kHz) 20dB Bandwidth (kHz) Insertion Loss (dB) Spurious Attenuation(1) (dB) Spurious Attenuation(2) (dB) Input/Output Impedance (ohm) SFSRA4M50CF00-B0 4.500 fn60 min. 600 max. 6.0 max. 30 min. [within 0 to fn] 20 min. [within fn to 7.0MHz] 1000 SFSRA4M50DF00-B0 4.500 fn70 min. 750 max. 6.0 max. 30 min. [within 0 to fn] 20 min. [within fn to 7.0MHz] 1000 SFSRA4M50EF00-B0 4.500 fn125 min. 850 max. 6.0 max. 25 min. [within 0 to fn] 18 min. [within fn to 7.0MHz] 1000 SFSRA5M50BF00-B0 5.500 fn50 min. 400 max. 8.0 max. 30 min. [within 0 to fn] 20 min. [within fn to 7.57MHz] 600 SFSRA5M50CF00-B0 5.500 fn60 min. 600 max. 6.0 max. 30 min. [within 0 to fn] 20 min. [within fn to7.5MHz] 600 SFSRA5M50DF00-B0 5.500 fn80 min. 750 max. 6.0 max. 30 min. [within 0 to fn] 20 min. [within fn to 7.5MHz] 600 SFSRA5M74BF00-B0 5.742 fn50 min. 400 max. 8.0 max. 30 min. [within 0 to fn] 20 min. [within fn to 8.0MHz] 600 SFSRA5M74CF00-B0 5.742 fn60 min. 600 max. 6.0 max. 30 min. [within 0 to fn] 20 min. [within fn to 7.5MHz] 600 SFSRA6M00CF00-B0 6.000 fn60 min. 600 max. 6.0 max. 30 min. [within 0 to fn] 20 min. [within fn to 8.0MHz] 470 SFSRA6M00DF00-B0 6.000 fn80 min. 750 max. 6.0 max. 30 min. [within 0 to fn] 20 min. [within fn to 8.0MHz] 470 SFSRA6M50CF00-B0 6.500 fn70 min. 650 max. 6.0 max. 30 min. [within 0 to fn] 20 min. [within fn to 8.5MHz] 470 SFSRA6M50DF00-B0 6.500 fn80 min. 800 max. 6.0 max. 30 min. [within 0 to fn] 20 min. [within fn to 8.5MHz] 470 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P25E3.pdf 01.10.17 Frequency Characteristics SFSRA4M50DF00-B0 0 10 10 20 20 Attenuation.(dB) Attenuation.(dB) SFSRA4M50CF00-B0 0 30 40 30 40 50 50 60 60 70 3.5 3.7 3.9 4.1 4.3 4.5 4.7 Frequency (MHz) 4.9 5.1 5.3 2 70 3.5 5.5 3.7 3.9 0 0 10 10 20 20 30 40 50 60 3.9 54 4.3 4.5 4.7 Frequency (MHz) 4.9 5.1 5.3 70 4.5 5.5 4.7 4.9 10 10 20 20 30 40 60 60 5.1 5.3 5.5 5.7 Frequency (MHz) 5.1 5.3 5.5 5.7 Frequency (MHz) 5.9 6.1 6.3 6.5 40 50 4.9 5.5 30 50 4.7 5.3 SFSRA5M50DF00-B0 0 Attenuation.(dB) Attenuation.(dB) SFSRA5M50CF00-B0 0 70 4.5 5.1 40 60 3.7 4.9 30 50 70 3.5 4.3 4.5 4.7 Frequency (MHz) SFSRA5M50BF00-B0 Attenuation.(dB) Attenuation.(dB) SFSRA4M50EF00-B0 4.1 5.9 6.1 6.3 70 4.5 6.5 4.7 4.9 SFSRA5M74BF00-B0 5.1 5.3 5.5 5.7 Frequency (MHz) 5.9 6.1 6.1 6.3 6.3 6.5 SFSRA5M74CF00-B0 0 0 10 10 20 Attenuation.(dB) Attenuation.(dB) 20 30 40 50 30 40 50 60 60 70 4.7 4.9 5.1 5.3 5.5 5.7 5.9 Frequency (MHz) 6.1 6.3 6.5 6.7 70 4.7 4.9 5.1 5.3 5.5 5.7 5.9 Frequency (MHz) 6.5 6.7 Continued on the following page. 7 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P25E3.pdf 01.10.17 Continued from the preceding page. Frequency Characteristics SFSRA6M00CF00-B0 0 0 10 10 20 20 Attenuation(dB) Attenuation(dB) 2 SFSRA6M00DF00-B0 30 40 30 40 50 50 60 60 70 5.0 5.2 5.4 5.6 5.8 6.0 6.2 Frequency (MHz) 6.4 6.6 6.8 70 5.0 7.0 5.2 5.4 0 0 10 10 20 20 30 40 60 60 5.9 6.1 6.3 6.5 6.7 Frequency (MHz) 6.6 6.8 7.0 7.1 7.3 7.5 40 50 5.7 6.4 30 50 70 5.5 5.8 6.0 6.2 Frequency (MHz) SFSRA6M50DF00-B0 Attenuation(dB) Attenuation(dB) SFSRA6M50CF00-B0 5.6 6.9 7.1 7.3 70 5.5 7.5 5.7 5.9 6.1 6.3 6.5 6.7 Frequency (MHz) 6.9 Spurious Response SFSRA4M50DF00-B0 0 10 10 20 20 Attenuation.(dB) Attenuation.(dB) SFSRA4M50CF00-B0 0 30 40 30 40 50 50 60 60 70 0.0 1.0 2.0 3.0 4.0 5.0 6.0 Frequency (MHz) 7.0 8.0 9.0 10.0 70 0.0 1.0 2.0 0 10 10 20 20 30 40 60 60 2.0 3.0 4.0 5.0 6.0 Frequency (MHz) 8.0 9.0 10.0 40 50 1.0 7.0 30 50 70 0.0 4.0 5.0 6.0 Frequency (MHz) SFSRA5M50BF00-B0 0 Attenuation.(dB) Attenuation.(dB) SFSRA4M50EF00-B0 3.0 7.0 8.0 9.0 10.0 70 0.0 1.0 2.0 3.0 4.0 5.0 6.0 Frequency (MHz) 7.0 8.0 9.0 10.0 Continued on the following page. 8 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P25E3.pdf 01.10.17 Continued from the preceding page. Spurious Response SFSRA5M50DF00-B0 0 10 10 20 20 Attenuation.(dB) Attenuation.(dB) SFSRA5M50CF00-B0 0 30 40 30 40 50 50 60 60 70 0.0 1.0 2.0 3.0 4.0 5.0 6.0 Frequency (MHz) 7.0 8.0 9.0 70 0.0 10.0 2 1.0 2.0 0 0 10 10 20 20 30 40 60 60 2.0 3.0 4.0 5.0 6.0 Frequency (MHz) 7.0 8.0 9.0 70 0.0 10.0 1.0 2.0 10 10 20 20 30 40 50 60 3.0 4.0 5.0 6.0 Frequency (MHz) 7.0 8.0 9.0 70 0.0 10.0 1.0 2.0 0 10 10 20 20 30 40 50 60 3.0 4.0 5.0 6.0 Frequency (MHz) 8.0 9.0 10.0 3.0 4.0 5.0 6.0 Frequency (MHz) 7.0 8.0 9.0 10.0 7.0 8.0 9.0 10.0 40 60 2.0 7.0 30 50 1.0 4.0 5.0 6.0 Frequency (MHz) SFSRA6M50DF00-B0 Attenuation.(dB) Attenuation.(dB) SFSRA6M50CF00-B0 0 70 0.0 3.0 40 60 2.0 10.0 30 50 1.0 9.0 SFSRA6M00DF00-B0 0 Attenuation.(dB) Attenuation.(dB) SFSRA6M00CF00-B0 0 70 0.0 8.0 40 50 1.0 7.0 30 50 70 0.0 4.0 5.0 6.0 Frequency (MHz) SFSRA5M74CF00-B0 Attenuation.(dB) Attenuation.(dB) SFSRA5M74BF00-B0 3.0 7.0 8.0 9.0 10.0 70 0.0 1.0 2.0 3.0 4.0 5.0 6.0 Frequency (MHz) Continued on the following page. 9 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. Continued from the preceding page. Test Circuit 1 2 3 R1 2 Rg S.S.G. R2 Rg+R1=R2=Input and Output Impedance C=10pF (Including stray capacitance and input capacitance of RF voltmeter) 10 C RF Voltmeter P25E3.pdf 01.10.17 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P25E3.pdf 01.10.17 CERAFILr(Filters/Traps/Discriminators) for TV/VCR CERAFILr Low-profile SFSRL Series SFSRL series are the Low-profile type of standard SFSRA series. EIAJ CODE MARKING Features 6.0 max. 10.0 max. 3 5.01.0 1.10.1 1. Installed height is 6.0mm, making it well suited for compact, thin sets. 2. Electrical char. and performance are the same as those of SFSRA series. 3. 2 types, narrow and middle bandwidth, are prepared. 0.50.1 2.5 0.2 4.0max. 0.30.1 2.5 0.2 (3) (2) (in mm) (1) Part Number Nominal Center Frequency (fn) (MHz) 3dB Bandwidth (kHz) 20dB Bandwidth (kHz) Insertion Loss (dB) Spurious Attenuation(1) (dB) Spurious Attenuation(2) (dB) Input/Output Impedance (ohm) SFSRL4M50CF00-B0 4.500 fn60 min. 600 max. 6.0 max. 30 min. [within 0 to fn] 15 min. [within fn to 7.0MHz] 1000 SFSRL4M50DF00-B0 4.500 fn70 min. 750 max. 6.0 max. 30 min. [within 0 to fn] 15 min. [within fn to 5.7MHz] 1000 SFSRL5M50CF00-B0 5.500 fn60 min. 600 max. 6.0 max. 30 min. [within 0 to fn] 15 min. [within fn to 7.0MHz] 600 SFSRL5M50DF00-B0 5.500 fn80 min. 750 max. 6.0 max. 30 min. [within 0 to fn] 15 min. [within fn to 7.0MHz] 600 SFSRL6M00CF00-B0 6.000 fn60 min. 600 max. 6.0 max. 30 min. [within 0 to fn] 15 min. [within fn to 7.5MHz] 470 SFSRL6M00DF00-B0 6.000 fn80 min. 750 max. 6.0 max. 30 min. [within 0 to fn] 15 min. [within fn to 7.5MHz] 470 SFSRL6M50CF00-B0 6.500 fn70 min. 650 max. 6.0 max. 30 min. [within 0 to fn] 15 min. [within fn to 8.5MHz] 470 SFSRL6M50DF00-B0 6.500 fn80 min. 800 max. 6.0 max. 30 min. [within 0 to fn] 15 min. [within fn to 8.0MHz] 470 Frequency Characteristics SFSRL4M50DF00-B0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) SFSRL4M50CF00-B0 0 30 40 30 40 50 50 60 60 70 3.5 3.7 3.9 4.1 4.3 4.5 4.7 Frequency (MHz) 4.9 5.1 5.3 5.5 70 3.5 3.7 3.9 4.1 4.3 4.5 4.7 4.9 5.1 5.3 5.5 Frequency (MHz) Continued on the following page. 11 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P25E3.pdf 01.10.17 Continued from the preceding page. Frequency Characteristics 3 SFSRL5M50DF00-B0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) SFSRL5M50CF00-B0 0 30 40 30 40 50 50 60 60 70 4.5 4.7 4.9 5.1 5.3 5.5 5.7 Frequency (MHz) 5.9 6.1 6.3 70 4.5 6.5 4.7 4.9 0 10 10 20 20 30 40 60 60 5.4 5.6 5.8 6.0 6.2 Frequency (MHz) 6.4 6.6 6.8 70 5.0 7.0 5.2 5.4 10 10 20 20 30 40 60 60 6.1 6.3 6.5 6.7 Frequency (MHz) 5.6 5.8 6.0 6.2 Frequency (MHz) 6.4 6.6 6.8 7.0 6.9 7.1 7.3 7.5 40 50 5.9 6.5 30 50 5.7 6.3 SFSRL6M50DF00-B0 0 Attenuation (dB) Attenuation (dB) SFSRL6M50CF00-B0 0 70 5.5 6.1 40 50 5.2 5.9 30 50 70 5.0 5.3 5.5 5.7 Frequency (MHz) SFSRL6M00DF00-B0 0 Attenuation (dB) Attenuation (dB) SFSRL6M00CF00-B0 5.1 6.9 7.1 7.3 70 5.5 7.5 5.7 5.9 6.1 6.3 6.5 6.7 Frequency (MHz) Spurious Response SFSRL4M50DF00-B0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) SFSRL4M50CF00-B0 0 30 40 30 40 50 50 60 60 70 0.0 1.0 2.0 3.0 4.0 5.0 6.0 Frequency (MHz) 7.0 8.0 9.0 10.0 70 0.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 Frequency (MHz) Continued on the following page. 12 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P25E3.pdf 01.10.17 Continued from the preceding page. Spurious Response SFSRL5M50DF00-B0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) SFSRL5M50CF00-B0 0 30 40 30 40 50 50 60 60 70 0.0 1.0 2.0 3.0 4.0 5.0 6.0 Frequency (MHz) 7.0 8.0 9.0 70 0.0 10.0 3 1.0 2.0 0 10 10 20 20 30 40 60 60 2.0 3.0 4.0 5.0 6.0 Frequency (MHz) 7.0 8.0 9.0 70 0.0 10.0 1.0 2.0 10 10 20 20 30 40 60 60 3.0 4.0 5.0 6.0 Frequency (MHz) 4.0 5.0 6.0 Frequency (MHz) 7.0 8.0 9.0 10.0 7.0 8.0 9.0 10.0 40 50 2.0 3.0 30 50 1.0 9.0 10.0 SFSRL6M50DF00-B0 0 Attenuation (dB) Attenuation (dB) SFSRL6M50CF00-B0 0 70 0.0 8.0 40 50 1.0 7.0 30 50 70 0.0 4.0 5.0 6.0 Frequency (MHz) SFSRL6M00DF00-B0 0 Attenuation (dB) Attenuation (dB) SFSRL6M00CF00-B0 3.0 7.0 8.0 9.0 10.0 70 0.0 1.0 2.0 3.0 4.0 5.0 6.0 Frequency (MHz) Test Circuit 1 2 3 R1 Rg S.S.G. R2 C RF Voltmeter Rg+R1=R2=Input and Output Impedance C=10pF (Including stray capacitance and input capacitance of RF voltmeter) 13 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P25E3.pdf 01.10.17 CERAFILr(Filters/Traps/Discriminators) for TV/VCR CERAFILr High-selectivity Type SFTRD Series 15.02.0 A T 7.52.0 Ceramic filter SFTRD_AF series are high selectivity filter which involves 3-elements filter unit. EIAJ CODE Features 5.01.0 1. Excellent shape factor. 2. Good performance for spurious suppression. 3. Four-terminals type. 4. Suitable for 2 channel Multi-sound TV of Germany and Korea. 0.50.1 (1) (3) 3.01.0 2.50.2 0.30.1 7.50.2 2.50.2 (2) (4) (in mm) Part Number Nominal Center Frequency (fn) (MHz) 3dB Bandwidth (kHz) 20dB Bandwidth (kHz) Insertion Loss (dB) SFTRD4M50AF00-B0 4.500 fn40 min. 370 max. 10.0 max. 50 min. 40 min. [within fn-1.0MHz to fn] [within fn to fn+0.8MHz] 1000 SFTRD5M50AF00-B0 5.500 fn50 min. 350 max. 9.0 max. 50 min. 50 min. [within fn-1.0MHz to fn] [within fn to fn+1.0MHz] 600 SFTRD5M74AF00-B0 5.742 fn50 min. 350 max. 9.0 max. 50 min. 50 min. [within fn-1.0MHz to fn] [within fn to fn+1.0MHz] 600 SFTRD6M00AF00-B0 6.000 fn50 min. 400 max. 9.0 max. 50 min. 50 min. [within fn-1.0MHz to fn] [within fn to fn+1.0MHz] 470 SFTRD6M50AF00-B0 6.500 fn50 min. 400 max. 9.0 max. 50 min. 50 min. [within fn-1.0MHz to fn] [within fn to fn+1.0MHz] 470 Spurious Attenuation(1) (dB) Spurious Attenuation(2) (dB) Input/Output Impedance (ohm) Frequency Characteristics SFTRD4M50AF00-B0 SFTRD5M50AF00-B0 0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) 4 1.40.1 30 40 30 40 50 50 60 60 70 4.0 4.1 4.2 4.3 4.4 4.5 4.6 Frequency (MHz) 4.7 4.8 4.9 5.0 70 4.5 4.7 4.9 5.1 5.3 5.5 5.7 5.9 6.1 6.3 6.5 Frequency (MHz) Continued on the following page. 14 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P25E3.pdf 01.10.17 Continued from the preceding page. Frequency Characteristics SFTRD6M00AF00-B0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) SFTRD5M74AF00-B0 0 30 40 30 40 50 50 60 60 70 5.2 5.3 5.4 5.5 5.6 5.7 5.8 Frequency (MHz) 5.9 6.0 6.1 6.2 6.7 6.8 6.9 7.0 70 5.5 5.6 5.7 5.8 5.9 6.0 6.1 Frequency (MHz) 6.2 6.3 6.4 6.5 4 SFTRD6M50AF00-B0 0 10 Attenuation (dB) 20 30 40 50 60 70 6.0 6.1 6.2 6.3 6.4 6.5 6.6 Frequency (MHz) Spurious Response SFTRD5M50AF00-B0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) SFTRD4M50AF00-B0 0 30 40 30 40 50 50 60 60 70 0.0 1.0 2.0 3.0 4.0 5.0 6.0 Frequency (MHz) 7.0 8.0 9.0 70 0.0 10.0 1.0 2.0 10 10 20 20 30 40 60 60 4.0 5.0 6.0 Frequency (MHz) 7.0 8.0 9.0 10.0 40 50 3.0 6.0 30 50 2.0 5.0 SFTRD6M00AF00-B0 0 Attenuation (dB) Attenuation (dB) SFTRD5M74AF00-B0 1.0 4.0 Frequency (MHz) 0 70 0.0 3.0 7.0 8.0 9.0 10.0 70 0.0 1.0 2.0 3.0 4.0 5.0 6.0 Frequency (MHz) 7.0 8.0 9.0 10.0 Continued on the following page. 15 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. Continued from the preceding page. Spurious Response SFTRD6M50AF00-B0 0 10 Attenuation (dB) 20 30 40 50 60 70 0.0 4 1.0 2.0 3.0 4.0 5.0 6.0 Frequency (MHz) 7.0 8.0 9.0 10.0 Test Circuit R1 (1) (2) (3) (4) Rg R2 S.S.G R.F. Voltmeter (1) : Input (2),(3) : Ground (3) : Output Rg + R1 = R2 = 330 C = 10pF (Including stray capacitance and input capacitance of RF voltmeter.) 16 C P25E3.pdf 01.10.17 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P25E3.pdf 01.10.17 CERAFILr(Filters/Traps/Discriminators) for TV/VCR CERAFILr Chroma Signal SFSRA/H/L Series 0.480.1 1. Frequency adjustment free. 2. Responsible for VHS. 8mm VCR system. 0.9 (Ref.) 7.0 (Ref.) Features 3.50.5 M 7.0 max. 10.0 max. Chroma signals frequency conversion process is involved in VCRs video signal processing circuit. These SFSRA/SFSRH/SFSRL series are suitable for B.P.F. 4.0 max. 2.50.2 2.50.2 SFSRA Series (3) (2) (1) 3--0.8 5 (in mm) 10.0 max. EIAJ CODE F4.5D M 8.0 max. MARKING 6.0 max. 10.0 max. 1.10.1 SFSRH Series 2.5 0.2 4.0 max. 0.30.1 2.5 0.2 0.50.1 (1) Input (2) Ground (3) Output SFSRL Series (3) (2) (1) 2.5 0.2 2.5 0.2 4.0max. 0.50.1 0.30.1 1.70.1 5.01.0 5.01.0 1.380.2 (in mm) (3) (2) (in mm) (1) Part Number Nominal Center Frequency (fn) (MHz) 3dB Bandwidth (kHz) 20dB Bandwidth (kHz) Insertion Loss (dB) Spurious Attenuation(1) (dB) Spurious Attenuation(2) (dB) Input/Output Impedance (ohm) SFSRA4M43CF00-B0 4.430 fn60 min. 600 max. 6.0 max. 30 min. [within 0 to fn] 20 min. [within fn to 7.0MHz] 1000 SFSRH3M58CF00-B0 3.580 fn40 min. 530 max. 6.0 max. 25 min. [within 0 to fn] 15 min. [within fn to 6.0MHz] 1000 SFSRL4M32DF00-B0 4.320 fn70 min. 750 max. 6.0 max. 30 min. [within 0 to fn] 15 min. [within fn to 5.5MHz] 1000 SFSRL5M17DF00-B0 5.170 fn70 min. 750 max. 7.5 max. 30 min. [within 0 to fn] 15 min. [within fn to 7.0MHz] 600 Frequency Characteristics SFSRH3M58CF00-B0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) SFSRA4M43CF00-B0 0 30 40 30 40 50 50 60 60 70 3.5 70 3.7 3.9 4.1 4.3 4.5 4.7 Frequency (MHz) 4.9 5.1 5.3 5.5 2.7 2.9 3.1 3.3 3.5 3.7 3.9 4.1 4.3 4.5 4.7 Frequency (MHz) Continued on the following page. 17 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P25E3.pdf 01.10.17 Continued from the preceding page. Frequency Characteristics SFSRL5M17DF00-B0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) SFSRL4M32DF00-B0 0 30 40 50 30 40 50 60 60 70 3.3 3.5 3.7 3.9 4.1 4.3 4.5 4.7 4.9 5.1 70 4.2 5.3 4.4 4.6 4.8 Frequency (MHz) 5.6 5.8 6.0 6.2 7.0 8.0 9.0 10.0 7.0 8.0 9.0 10.0 Spurious Response SFSRH3M58CF00-B0 0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) SFSRA4M43CF00-B0 30 40 30 40 50 50 60 60 70 0.0 70 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 0.0 1.0 2.0 3.0 Frequency (MHz) 10 10 20 20 Attenuation (dB) 0 30 40 50 30 40 60 70 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 Frequency (MHz) Test Circuit 1 2 3 R1 Rg R2 Rg+R1=R2=Input and Output Impedance C=10pF (Including stray capacitance and input capacitance of RF voltmeter) 18 6.0 50 60 S.S.G. 5.0 SFSRL5M17DF00-B0 0 0.0 4.0 Frequency (MHz) SFSRL4M32DF00-B0 Attenuation (dB) 5 5.0 5.2 5.4 Frequency (MHz) C RF Voltmeter 70 0.0 1.0 2.0 3.0 4.0 5.0 6.0 Frequency (MHz) Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P25E3.pdf 01.10.17 CERAFILr Lead Type Notice Notice (Soldering and Mounting) The component cannot be withstand washing. Notice (Handling) 1. Do not use this product with bend. The component may be damaged if excess mechanical stress is applied to it mounted on the printed circuit board. 2. The component may be damaged when an excess stress will be applied. 3. All kinds of re-flow soldering must not be applied on the component. 4. Do not clean or wash the component as it is not hermetically sealed. 5. Please contact Murata or Murata representative for soldering condition, in case of using lead free solder. 6. Do not use strong acidity flux, more than 0.2wt% chlorine content, in flow soldering. 7. In case of covering filter with over coat, conditions such as material of resin, cure temperature, and so on should be evaluated well. 8. Accurate test circuit values are required to measure electrical characteristics. It may be a cause of miss-correlation if there is any deviation, especially stray capacitance, from the test circuit in the specification. 5 19 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P25E3.pdf 01.10.17 CERAFILr(Filters/Traps/Discriminators) for TV/VCR Ceramic Traps Chip Type TPSKA Series SMD ceramic trap TPSKA_B is small and thin SMD trap sealed with a metal cap. Recommended for LCD-TVs, and small and thin tuners. 7.90.2 3.00.1 1.80.2 Features 0.50.1 8.50.2 1. High attenuation and high performance group delay time. 2. Small and thin pakage. 3. Reflow-solderable. 0.60.2 3.80.2 1.00.1 Marking : TAB 1.30.2 : Vender's Code : EIAJ Monthly code 0.30.1 (1) : Input (2) : Ground (3) : Output 1.30.2 (1) (2) (3) Electrode in mm 2.50.2 2.50.2 Part Number Nominal Center Frequency (fn1) (MHz) Attenuation (at fn1) (dB) 30dB Attenuation BW (fn1) (kHz) 4.500 35 min. 50 min. TPSKA4M50B00-R1 Spurious Response 0 0 700 10 10 600 20 Attenuation (dB) Attenuation (dB) Frequency Characteristics 30 40 50 60 20 500 30 400 40 300 50 200 60 100 70 0 80 70 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 0 1.0 2.0 Frequency (MHz) Test Circuit 3.0 Frequency (MHz) 4.0 5.0 Standard Land Pattern Dimensions L 1.0 R1 1.0 1.5 1.0 1.5 Rg R2 RF Voltmeter S.S.G. Rg=50 R1=330 R2=1.0k 20 L=15H 4.8 50 G.D.T. (nsec) 6 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P25E3.pdf 01.10.17 CERAFILr(Filters/Traps/Discriminators) for TV/VCR Double Trap Chip Type TPWKA Series M 4.20.1 0.40.1 7.90.2 1.50.2 SMD ceramic trap TPWKA is small and thin SMD trap sealed with a metal cap. Recommended for LCD-TVs, and small and thin tuners. This series consist of 2 wafers with 2 trap frequencies. Recommended for Multi standard set. 5.00.2 1.00.1 Features 1. Good performance of attenuation. 2. Small and thin package. 3. Reflow-solderable. 1.30.2 8.50.2 0.40.2 1.30.2 0.30.1 (1) (2) (3) 2.50.2 2.50.2 : Electrode (1) : Input or Output (2) : Ground (3) : Output or Input (in mm) Part Number Nominal Center Frequency (fn1) (MHz) Nominal Center Frequency (fn2) (MHz) Attenuation (at fn1) (dB) Attenuation (at fn2) (dB) 30dB Attenuation BW (fn1) (kHz) TPWKA5M50B04-R1 5.500 5.742 30 min. 30 min. 50 min. 7 0 0 10 10 800 20 600 30 400 40 200 50 50 0 60 60 20 30 40 70 70 4.5 4.7 4.9 5.1 5.3 5.5 5.7 Frequency (MHz) 5.9 6.1 6.3 6.5 Test Circuit 0 1.0 2.0 4.0 5.0 6.0 Frequency (MHz) 7.0 8.0 9.0 10.0 Standard Land Pattern Dimensions 1.2 L 1.2 1.3 1.2 1.3 1.9 R1 Rg 50 R2 C2 L = 8.2 H Rg = 50 R1 = 150 R2 = 330 C2 = 10pF (Including stray capacitance and input capacitance of RF voltmeter) 5.8 RF Voltmeter 1.9 S.S.G. 3.0 G.D.T.(nesc) Spurious Response Attenuation.(dB) Attenuation.(dB) Frequency Characteristics (in mm) 21 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P25E3.pdf 01.10.17 Ceramic Trap Chip Type Notice Notice (Soldering and Mounting) 1. Standard Reflow Soldering Condition (1) Reflow Trap is soldered one time within the following temperature condition and then being placed in natural condition for 4 hours. 5 sec. 240 (2) Soldering Iron Lead terminal is directly contacted with the tip of soldering iron of 2805C for 3.0 seconds 0.5 seconds, and then being placed in natural condition for 4 hours. Temperature (C) 230 Gradual Cooling 150 2. Wash The component cannot be withstand washing. 60 30 Time (sec.) Notice (Handling) 7 1. The component may be damaged if excess mechanical stress is applied to it mounted on the printed circuit board. 2. Design layout of components on the PC board to minimize the stress imposed on the wrap or flexure of the board. 3. After installing chips, if solder is excessively applied to the circuit board, mechanical stress will cause destruction resistance characteristics to lower. To prevent this, be extremly careful in determining shape and dimension before designing the circuit board diagram. 4. When the positioning claws and pick up nozzle are worn, the load is applied to the chip while positioning is concentrated to one positioning accuracy, etc. Careful checking and maintenance are necessary to prevent unexpected trouble. 5. When correcting chips with a soldering iron, the tip of the soldering iron should not directly touch the chip component. 6. Cleaning or washing of the component is not acceptable due to non sealed construction. 7. In case of covering filter with over coat, conditions such as material of resin, cure temperature, and so on should be evaluated well. 8. Accurate test circuit values are required to measure electrical characteristics. It may be a cause of misscorrelation if there is any deviation, especially stray capacitance, from the test circuit in the specification. 22 [Component direction] Put the component lateral to the direction in which stress acts. [Component layout close to board] Perforation A Susceptibility to stress is in the order of;A>C>B B Slit C Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P25E3.pdf 01.10.17 CERAFILr(Filters/Traps/Discriminators) for TV/VCR Ceramic Traps Three-terminals TPSRA Series Features 0.9 (Ref.) 2.50.2 2.50.2 4.0 max. 0.480.1 7.0 (Ref.) 3.50.5 M 7.0 max. 10.0 max. As part of the environment protection activity, solder for terminal plating and terminal-element connection inside of ceramic filter TPSRA series contain no lead(Pb). This series consist of 2 trap element on one wafer. Suitable for the sound IF trap of CTV/VCR. 1. Good performance of attenuation. 2. Shape factor can be changed by the value of Inductor "L". 3. Three-terminals type. 4. Low profile (H=7.0mm max.). 5. Lead dimension: Improved mounting reliability(cut & clinch) due to round terminal. 3--0.8 Nominal Center Frequency (fn1) (MHz) Attenuation (at fn1) (dB) 30dB Attenuation BW (fn1) (kHz) TPSRA4M50B00-B0 4.500 35 min. 50 min. TPSRA4M50C00-B0 4.500 30 min. - TPSRA5M50B00-B0 5.500 35 min. 70 min. TPSRA5M74B00-B0 5.742 35 min. 70 min. TPSRA6M00B00-B0 6.000 35 min. 70 min. TPSRA6M50B00-B0 6.500 35 min. 70 min. Part Number (in mm) 8 Frequency Characteristics TPSRA4M50C00-B0 0 0 10 10 Attenuation(dB) Attenuation(dB) TPSRA4M50B00-B0 20 30 40 20 30 40 50 50 60 60 70 4.0 4.1 4.2 4.3 4.4 4.5 4.6 Frequency (MHz) 4.7 4.8 4.9 5.0 70 4.0 4.1 4.2 4.3 4.4 4.5 4.6 Frequency (MHz) 4.7 4.8 4.9 5.0 Continued on the following page. 23 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P25E3.pdf 01.10.17 Continued from the preceding page. Frequency Characteristics TPSRA5M74B00-B0 0 0 10 10 Attenuation (dB) Attenuation (dB) TPSRA5M50B00-B0 20 30 40 20 30 40 50 50 60 60 70 5.0 5.1 5.2 5.3 5.4 5.5 5.6 Frequency (MHz) 5.7 5.8 5.9 70 5.2 6.0 5.3 5.4 0 0 10 10 20 30 40 60 5.8 5.9 6.0 6.1 Frequency (MHz) 8 6.1 6.2 6.7 6.8 6.9 7.0 40 60 5.7 6.0 30 50 5.6 5.9 20 50 70 5.5 5.6 5.7 5.8 Frequency (MHz) TPSRA6M50B00-B0 Attenuation (dB) Attenuation (dB) TPSRA6M00B00-B0 5.5 6.2 6.3 6.4 70 6.0 6.5 6.1 6.2 6.3 6.4 6.5 6.6 Frequency (MHz) Spurious Response TPSRA4M50B00-B0 TPSRA4M50C00-B0 20 600 30 400 40 200 50 0 60 800 20 600 30 400 40 200 50 0 60 0 1.0 2.0 3.0 4.0 5.0 6.0 Frequency (MHz) 7.0 8.0 9.0 70 10.0 0 1.0 2.0 TPSRA5M50B00-B0 7.0 8.0 9.0 10.0 0 800 20 600 30 400 40 200 50 0 Attenuation.(dB) 10 G.D.T.(nesc) Attenuation.(dB) 4.0 5.0 6.0 Frequency (MHz) TPSRA5M74B00-B0 0 10 800 20 600 30 400 40 200 50 0 60 60 70 3.0 70 0 1.0 2.0 3.0 4.0 5.0 6.0 Frequency (MHz) 7.0 8.0 9.0 10.0 0 1.0 2.0 3.0 4.0 5.0 6.0 Frequency (MHz) 7.0 8.0 9.0 10.0 Continued on the following page. 24 G.D.T.(nesc) 70 10 G.D.T.(nesc) 800 Attenuation.(dB) 0 10 G.D.T.(nesc) Attenuation.(dB) 0 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P25E3.pdf 01.10.17 Continued from the preceding page. Spurious Response TPSRA6M00B00-B0 TPSRA6M50B00-B0 600 30 400 40 200 50 0 10 800 20 600 30 400 40 200 50 0 60 60 70 Attenuation.(dB) 20 G.D.T.(nesc) Attenuation.(dB) 800 G.D.T.(nesc) 0 0 10 0 1.0 2.0 3.0 4.0 5.0 6.0 Frequency (MHz) 7.0 8.0 9.0 10.0 70 0 1.0 2.0 3.0 4.0 5.0 6.0 Frequency (MHz) 7.0 8.0 9.0 10.0 Test Circuit TPSRA4M50B00-B0 TPSRA4M50C00-B0 15H 8.2H 330ohm 220ohm Rg=50ohm S.S.G. 1Kohm R.F. Voltmeter 50ohm 50ohm S.S.G. 2.2Kohm Rg=50ohm R.F. Voltmeter 8 TPSRA5M50/5M74/6M00/6M50B00-B0 15H 220ohm 1Kohm S.S.G. 50ohm Rg=50ohm R.F. Voltmeter 25 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P25E3.pdf 01.10.17 CERAFILr(Filters/Traps/Discriminators) for TV/VCR Ceramic Traps Two-terminals TPSRD Series 10.0 max. T J 10.0 max. Ceramic Trap TPSRD_J series are two-terminals type. Which are recommended for the attenuation of sound IF in B/W TV and the attenuation of chroma signal in Video Camcorder. EIAJ CODE 1. Small-size, Light-weight. 2. High performance, durability. 3. Easy to design due to two-terminals type. 5.01.0 1.380.2 Features 5.00.2 5.0 max. 0.30.1 0.50.1 Nominal Center Frequency (fn1) (MHz) Attenuation (at fn1) (dB) 30dB Attenuation BW (fn1) (kHz) TPSRD3M58J00-B0 3.580 20 min. 20 min.[20dB Att.BW] TPSRD4M43J00-B0 4.430 20 min. 40 min.[20dB Att.BW] TPSRD4M50J00-B0 4.500 20 min. 30 min.[20dB Att.BW] TPSRD5M50J00-B0 5.500 20 min. 30 min.[20dB Att.BW] TPSRD6M00J00-B0 6.000 20 min. 40 min.[20dB Att.BW] TPSRD6M50J00-B0 6.500 20 min. 40 min.[20dB Att.BW] Part Number in mm Frequency Characteristics TPSRD3M58J00-B0 TPSRD4M43J00-B0 0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) 9 30 40 30 40 50 50 60 60 70 3.1 3.2 3.3 3.4 3.5 3.6 3.7 Frequency (MHz) 3.8 3.9 4.0 70 3.9 4.1 4.0 4.1 0 0 10 10 20 20 30 40 60 60 4.2 4.3 4.4 4.5 4.6 Frequency (MHz) 4.7 4.8 4.9 5.7 5.8 5.9 6.0 40 50 4.1 4.6 30 50 70 4.0 4.3 4.4 4.5 Frequency (MHz) TPSRD5M50J00-B0 Attenuation (dB) Attenuation (dB) TPSRD4M50J00-B0 4.2 4.7 4.8 4.9 5.0 70 5.0 5.1 5.2 5.3 5.4 5.5 5.6 Frequency (MHz) Continued on the following page. 26 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P25E3.pdf 01.10.17 Continued from the preceding page. Frequency Characteristics TPSRD6M50J00-B0 0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) TPSRD6M00J00-B0 30 40 30 40 50 50 60 60 70 5.5 5.6 5.7 5.8 5.9 6.0 6.1 Frequency (MHz) 6.2 6.3 6.4 70 6.0 6.5 6.1 6.2 6.3 6.4 6.5 6.6 Frequency (MHz) 6.7 6.8 6.9 7.0 7.0 8.0 9.0 10.0 Spurious Response TPSRD4M43J00-B0 0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) TPSRD3M58J00-B0 30 40 30 40 50 50 60 60 70 0.0 1.0 2.0 3.0 4.0 5.0 6.0 Frequency (MHz) 7.0 8.0 9.0 70 0.0 10.0 1.0 2.0 0 0 10 10 20 20 30 40 40 50 60 60 1.0 2.0 3.0 4.0 5.0 6.0 Frequency (MHz) 7.0 8.0 9.0 70 0.0 10.0 1.0 2.0 0 10 10 20 20 30 40 60 60 3.0 4.0 5.0 6.0 Frequency (MHz) 7.0 8.0 9.0 10.0 7.0 8.0 9.0 10.0 40 50 2.0 4.0 5.0 6.0 Frequency (MHz) 30 50 1.0 3.0 TPSRD6M50J00-B0 Attenuation (dB) Attenuation (dB) TPSRD6M00J00-B0 0 70 0.0 9 30 50 70 0.0 4.0 5.0 6.0 Frequency (MHz) TPSRD5M50J00-B0 Attenuation (dB) Attenuation (dB) TPSRD4M50J00-B0 3.0 7.0 8.0 9.0 10.0 70 0.0 1.0 2.0 3.0 4.0 5.0 6.0 Frequency (MHz) Continued on the following page. 27 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. Continued from the preceding page. Test Circuit 75 S.S.G. 9 28 1K 50 Rg=50 Ceramic Trap R.F. Voltmeter P25E3.pdf 01.10.17 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P25E3.pdf 01.10.17 CERAFILr(Filters/Traps/Discriminators) for TV/VCR Ceramic Traps TPSRD Series for 2ch Sound TV in Germany 7.02.0 Ceramic trap TPSRD_W series has same structure as TPSRD_B series. But they can trap 2 individual frequencies in one time. Recommended for 2 channels multi-sound TV system. 7.02.0 T EIAJ CODE 5.01.0 1.380.2 1.70.1 Features 0.50.1 2.5 0.2 2.5 0.2 3.01.0 0.30.1 1. Space saving. 2. Three-terminals type. (3) (2) in mm (1) Part Number Nominal Center Frequency (fn1) (MHz) Nominal Center Frequency (fn2) (MHz) Attenuation (at fn1) (dB) Attenuation (at fn2) (dB) 30dB Attenuation BW (fn1) (kHz) TPSRD5M50W00-B0 5.500 5.742 32 min. 25 min. 70 min. Spurious Response 0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) Frequency Characteristics 30 40 30 40 50 50 60 60 70 5.0 5.1 5.2 5.3 5.4 5.5 5.6 Frequency (MHz) 5.7 5.8 5.9 6.0 70 0.0 10 1.0 2.0 3.0 4.0 5.0 6.0 Frequency (MHz) 7.0 8.0 9.0 10.0 Test Circuit 15H S.S.G. 1Kohm Rg=50ohm 50ohm 330ohm R.F. Voltmeter 29 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P25E3.pdf 01.10.17 CERAFILr(Filters/Traps/Discriminators) for TV/VCR Double Traps TPWRD Series 7.02.0 T W B 7.02.0 Ceramic trap TPWRD_B series consist of 2 wafers with 2 trap frequencies. Recommended for Dual standard set. EIAJ CODE Features 1. Good performance of attenuation. 2. Small and thin package. 3. Three-terminals type. 5.01.0 1.380.2 1.70.1 0.50.1 3.51.0 0.30.1 2.50.2 2.50.2 in mm Part Number Nominal Center Frequency (fn1) (MHz) Nominal Center Frequency (fn2) (MHz) Attenuation (at fn1) (dB) Attenuation (at fn2) (dB) 30dB Attenuation BW (fn1) (kHz) TPWRD5M50B02-B0 5.500 6.500 30 min. 30 min. 50 min. TPWRD5M50B03-B0 5.500 6.000 30 min. 30 min. 50 min. TPWRD5M50B04-B0 5.500 5.742 30 min. 30 min. 50 min. TPWRD6M00B01-B0 6.000 6.500 30 min. 30 min. 70 min. Frequency Characteristics 11 TPWRD5M50B03-B0 0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) TPWRD5M50B02-B0 30 40 30 40 50 50 60 60 70 5.0 5.2 5.4 5.6 5.8 6.0 6.2 Frequency (MHz) 6.4 6.6 6.8 70 4.5 7.0 4.7 4.9 0 0 10 10 20 20 30 40 60 60 4.9 5.1 5.3 5.5 5.7 Frequency (MHz) 6.1 6.3 6.5 6.4 6.6 6.8 7.0 40 50 4.7 5.9 30 50 70 4.5 5.3 5.5 5.7 Frequency (MHz) TPWRD6M00B01-B0 Attenuation (dB) Attenuation (dB) TPWRD5M50B04-B0 5.1 5.9 6.1 6.3 6.5 70 5.0 5.2 5.4 5.6 5.8 6.0 6.2 Frequency (MHz) Continued on the following page. 30 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P25E3.pdf 01.10.17 Continued from the preceding page. Spurious Response TPWRD5M50B03-B0 0 0 10 10 20 20 Attenuation (dB) Attenuation (dB) TPWRD5M50B02-B0 30 40 30 40 50 50 60 60 70 0.0 1.0 2.0 3.0 4.0 5.0 6.0 Frequency (MHz) 7.0 8.0 9.0 70 0.0 10.0 1.0 2.0 0 0 10 10 20 20 30 40 60 60 2.0 3.0 4.0 5.0 6.0 Frequency (MHz) 8.0 9.0 10.0 7.0 8.0 9.0 10.0 40 50 1.0 7.0 30 50 70 0.0 4.0 5.0 6.0 Frequency (MHz) TPWRD6M00B01-B0 Attenuation (dB) Attenuation (dB) TPWRD5M50B04-B0 3.0 7.0 8.0 9.0 10.0 70 0.0 1.0 2.0 3.0 4.0 5.0 6.0 Frequency (MHz) Test Circuit 8.2H 150ohm 330ohm S.S.G. 50ohm Rg=50ohm R.F. Voltmeter 11 31 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P25E3.pdf 01.10.17 CERAFILr(Filters/Traps/Discriminators) for TV/VCR Triple Traps TPTRD Series 8.02.0 T T B EIAJ CODE 7.02.0 Ceramic trap TPTRD_B series consist of 3 wafers with 3 trap frequencies. Recommended for Multi standard set. Features 1.380.2 1. Good performance of attenuation. 2. Space saving for Multi set. 3. Three-terminals type. 5.01.0 1.70.1 0.30.1 0.50.1 5.0 max. 2.50.2 2.50.2 in mm Part Number Nominal Center Frequency (fn1) (MHz) Nominal Center Frequency (fn2) (MHz) Nominal Center Frequency (fn3) (MHz) Attenuation (at fn1) (dB) Attenuation (at fn2) (dB) Attenuation (at fn3) (dB) 30dB Attenuation BW (fn1) (kHz) TPTRD5M50B01-B0 5.500 6.000 6.500 30 min. 30 min. 30 min. 50 min. Frequency Characteristics Spurious Response TPTRD5M50B01-B0 0 0 10 10 20 20 Attenuation ( dB ) Attenuation ( dB ) TPTRD5M50B01-B0 30 40 50 60 50 60 70 80 80 5.500 6.000 6.500 7.000 Test Circuit 12 8.2H 150ohm 330ohm Rg=50ohm 50ohm 90 0.0 2.5 5.0 Frequency ( MHz ) Frequency ( MHz ) 32 40 70 90 5.000 S.S.G. 30 R.F. Voltmeter 7.5 10.0 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P25E3.pdf 01.10.17 Ceramic Trap Lead Type Notice Notice (Soldering and Mounting) The component cannot be withstand washing. Notice (Handling) 1. Do not use this product with bend. The component may be damaged if excess mechanical stress is applied to it mounted on the printed circuit board. 2. The component may be damaged when an excess stress will be applied. 3. All kinds of re-flow soldering must not be applied on the component. 4. Do not clean or wash the component as it is not hermetically sealed. 5. Please contact Murata or Murata representative for soldering condition, in case of using lead free solder. 6. Do not use strong acidity flux, more than 0.2wt% chlorine content, in flow soldering. 7. In case of covering filter with over coat, conditions such as material of resin, cure temperature, and so on should be evaluated well. 8. Accurate test circuit values are required to measure electrical characteristics. It may be a cause of miss-correlation if there is any deviation, especially stray capacitance, from the test circuit in the specification. 12 33 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P25E3.pdf 01.10.17 CERAFILr(Filters/Traps/Discriminators) for TV/VCR Discriminators Wide-Band Type CDSRH Series 10.0 max. MARKING 8.0 max. Ceramic discriminator CDSRH series is a wide band, low profil type using thickness shear mode vibration. EIAJ CODE Features 1. Low profile 8.0mm type. 2. Suitable for Multi-sound Broadcasting system. 3. Two-terminals type and three-terminals type are available. 5.01.0 1.380.2 0.50.1 5.00.2 4.0max. 0.30.1 CDSRH_EK Series Unit : mm EIAJ M A R K I N G CODE 5.01.0 1.380.2 1.70.1 2.50.2 2.50.2 4.0max. 0.30.1 0.50.1 CDSRH_CK Series (3) 13 8.0 max. 10.0 max. (2) (1) (in mm) Part Number Nominal Center Frequency (fn) (MHz) Recovered Audio 3dB BW (kHz) Recovered Audio Output Voltage(at fn) (mV) Distortion (%) IC Detection Method CDSRH4M50EK020-B0 4.500 fn80 min. 245 min. 1.0 max. LA7550/7555 Quadrature CDSRH4M50EK023-B0 4.500 fn60 min. 230 min. 2.5 max. M51496P Quadrature CDSRH4M50EK035-B0 4.500 fn55 min. 240 min. 1.0 max. LA7680/7681 Quadrature CDSRH4M50EK049-B0 4.500 fn100 min. 220 min. 1.0 max. LA7577 Quadrature CDSRH4M50EK060-B0 4.500 fn90 min. 90 min. 1.0 max. M52318SP Quadrature CDSRH4M50EK069-B0 4.500 fn60 min. 320 min. 1.5 max. TA8701N Quadrature CDSRH4M50EK070-B0 4.500 fn50 min. 65 min. 1.5 max. M52007FP Quadrature CDSRH5M50EK023-B0 5.500 fn45 min. 220 min. 1.0 max. M51496P Quadrature CDSRH5M50EK035-B0 5.500 fn80 min. 350 min. 1.0 max. LA7680/7681 Quadrature CDSRH5M50EK049-B0 5.500 fn60 min. 500 min. 1.0 max. LA7577 Quadrature CDSRH5M50EK054-B0 5.500 fn100 min. 300 min. 1.2 max. TDA3857 Quadrature CDSRH5M50EK060-B0 5.500 fn70 min. 190 min. 1.5 max. M52318SP Quadrature CDSRH5M74EK054-B0 5.742 fn90 min. 340 min. 1.2 max. TDA3857 Quadrature CDSRH6M00EK049-B0 6.000 fn60 min. 500 min. 1.0 max. LA7577 Quadrature CDSRH6M00EK054-B0 6.000 fn90 min. 340 min. 1.5 max. TDA3857 Quadrature CDSRH6M00EK060-B0 6.000 fn60 min. 180 min. 2.5 max. M52318SP Quadrature CDSRH6M50EK020-B0 6.500 fn110 min. 350 min. 1.2 max. LA7550/7555 Quadrature CDSRH6M50EK049-B0 6.500 fn60 min. 500 min. 1.0 max. LA7577 Quadrature CDSRH6M50EK054-B0 6.500 fn90 min. 340 min. 1.5 max. TDA3857 Quadrature CDSRH6M50EK060-B0 6.500 fn60 min. 160 min. 2.5 max. M52318SP Quadrature CDSRH4M50CK020-B0 4.500 fn50 min. 280 min. 2.0 max. PC1382C Quadrature CDSRH4M50CK026-B0 4.500 fn40 min. 70 min. 1.2 max. LA7530 Quadrature CDSRH4M50CK029-B0 4.500 fn65 min. 250 min. 1.2 max. M51365SP Quadrature CDSRH4M50CK030-B0 4.500 fn40 min. within130 +30/-20mV 3.0 max. M51348FP Quadrature Continued on the following page. 34 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P25E3.pdf 01.10.17 Continued from the preceding page. Part Number Nominal Center Frequency (fn) (MHz) Recovered Audio 3dB BW (kHz) Recovered Audio Output Voltage(at fn) (mV) Distortion (%) CDSRH5M50CK026-B0 5.500 fn50 min. 500 min. CDSRH5M50CK029-B0 5.500 fn70 min. 420 min. CDSRH5M50CK030-B0 5.500 fn55 min. CDSRH6M00CK026-B0 6.000 CDSRH6M00CK029-B0 IC Detection Method 3.0 max. LA7530 Quadrature 1.5 max. M51365SP Quadrature 150 min. 3.0 max. M51348FP Quadrature fn50 min. 400 min. 3.0 max. LA7530 Quadrature 6.000 fn70 min. 450 min. 1.7 max. M51365SP Quadrature CDSRH6M00CK030-B0 6.000 fn55 min. 150 min. 3.0 max. M51348FP Quadrature CDSRH6M50CK020-B0 6.500 fn60 min. 480 min. 2.0 max. PC1382C Quadrature CDSRH6M50CK026-B0 6.500 fn35 min. 400 min. 3.0 max. LA7530 Quadrature CDSRH6M50CK029-B0 6.500 fn70 min. 430 min. 2.0 max. M51365SP Quadrature Characteristics shown above is as of 100% Dev. Part Numbers are varied with applied IC. Please note circuits and specifications are also varied with IC. (->Please check TM1561) Frequency Characteristics CDSRH4M50EK049-B0 CDSRH4M50CK029-B0 300 300 10 1 100 10 10 1 Distoriton Distoriton 1 0.1 4.3 4.5 Distoriton (%) 10 Recovered AF Output Voltage (mV) AF Output 100 Distoriton (%) Recovered AF Output Voltage (mV) AF Output 1 0.1 4.3 4.7 4.5 4.7 Frequency (MHz) Frequency (MHz) Test Circuit CDSRH4M50CK029-B0 IF-in 22 21 20 19 18 17 16 15 14 0.01 13 IN 4 5 6 7 8 9 10 11 12 4.7 19 + 7 10 12 Vcc (12V) AF Out 13 Vcc=12V 0.01 100 10n 18 10n DC Out 17 M51365SP (MITSUBISHI) 14 680 5.6k 3 10k 15n AF-out 2 18 13 50 LA7577 (SANYO) 1 (2) 0.01 23 12P Ground + 10 0.01 24 (3) 680 3.3k 10n (1) 680 CDSRH4M50EK049-B0 Ground 35 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P25E3.pdf 01.10.17 CERAFILr(Filters/Traps/Discriminators) for TV/VCR Discriminators Low-Profile Type CDSRL Series Ceramic discriminator CDSRL series is a wide band, low profile type using thickness shear mode vibration. EIAJ CODE MARKING Features 1. Low profile 6.0mm type. 2. Suitable for Multi-sound Broadcasting system. 3. Two-terminals type and three-terminals type are available. 6.0 max. 10.0 max. 5.01.0 1.00.2 0.50.1 5.00.2 4.0max. 0.30.1 CDSRL_EK Series Unit : mm EIAJ CODE MARKING 5.01.0 1.10.1 1.70.1 2.50.2 2.50.2 4.0max. 0.30.1 0.50.1 CDSRL_CK Series (3) Part Number Nominal Center Frequency (fn) (MHz) CDSRL4M50EK020-B0 CDSRL5M50EK020-B0 6.0 max. 10.0 max. (2) (1) (in mm) Recovered Audio 3dB BW (kHz) Recovered Audio Output Voltage(at fn) (mV) Distortion (%) IC Detection Method 4.500 fn80 min. 245 min. 1.0 max. LA7550/7555 Quadrature 5.500 fn100 min. 330 min. 1.2 max. LA7550/7555 Quadrature CDSRL4M50CK020-B0 4.500 fn50 min. 280 min. 2.0 max. PC1382C Quadrature CDSRL4M50CK029-B0 4.500 fn65 min. 250 min. 1.2 max. M51365SP Quadrature CDSRL4M50CK030-B0 4.500 fn40 min. within130 +30/-20mV 3.0 max. M51348FP Quadrature CDSRL5M50CK030-B0 5.500 fn55 min. 150 min. 3.0 max. M51348FP Quadrature CDSRL6M00CK029-B0 6.000 fn70 min. 450 min. 1.7 max. M51365SP Quadrature CDSRL6M00CK030-B0 6.000 fn55 min. 150 min. 3.0 max. M51348FP Quadrature CDSRL6M50CK020-B0 6.500 fn60 min. 480 min. 2.0 max. PC1382C Quadrature CDSRL6M50CK026-B0 6.500 fn35 min. 400 min. 3.0 max. LA7530 Quadrature Characteristics shown above is as of 100% Dev. Part Numbers are varied with applied IC. Please note circuits and specifications are also varied with IC. (->Please check TM1561) 14 36 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P25E3.pdf 01.10.17 Frequency Characteristics CDSRL4M50EK020-B0 CDSRL4M50CK029-B0 500 300 300 AF Output 1 100 10 10 1 Distoriton (%) 10 Recovered AF Output Voltage (mV) 10 Distoriton (%) Recovered AF Output Voltage (mV) AF Output 100 Distoriton Distoriton 1 1 0.1 4.3 4.5 0.1 4.3 4.7 4.5 4.7 Frequency (MHz) Frequency (MHz) CDSRL4M50EK020-B0 CDSRL4M50CK029-B0 Test Circuit 0.01 19 18 17 15 14 IN 13 LA7550 (SANYO) 2 6 7 9 11 12 M51365SP (MITSUBISHI) 14 0.01 0.01 22 1.2k 8 DC Out 17 4.7 19 + AF Out 7 10 12 Vcc=12V - 0.01 + Ground + 10 0.01 100 0.01 0.015 AF OUT 5.6k 0.01 18 13 0.01 1 (2) 50 20 24 12P 0.01 3.3k DC5V Chang (3) 680 Vcc 9V 680 (1) 0.01 0.01 0.01 SIF IN Ground 14 37 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P25E3.pdf 01.10.17 Ceramic Discriminator Notice Notice (Soldering and Mounting) The component cannot be withstand washing. Notice (Handling) 1. Do not use this product with bend. The component may be damaged if excess mechanical stress is applied to it mounted on the printed circuit board. 2. The component may be damaged when an excess stress will be applied. 3. All kinds of re-flow soldering must not be applied on the component. 4. Do not clean or wash the component as it is not hermetically sealed. 5. Please contact Murata or Murata representative for soldering condition, in case of using lead free 14 38 solder. 6. Do not use strong acidity flux, more than 0.2wt% chlorine content, in flow soldering. 7. In case of covering filter with over coat, conditions such as material of resin, cure temperature, and so on should be evaluated well. 8. Accurate test circuit values are required to measure electrical characteristics. It may be a cause of miss-correlation if there is any deviation, especially stray capacitance, from the test circuit in the specification. Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P25E3.pdf 01.10.17 Chip Type Packaging Chip Type Minimum Quantity 3000 pcs./dia. 330mm Reel 500 pcs./Bag (TPWKA series only) SFSKA/TPSKA Series Part Number marked side is always facing upside. 7.50.1 9.00.1 400-560 Peeling strength (20-60gr.) Cover tape +0.1 o1.5 -0.0 8.00.1 4.30.1 Chip filter 3 max. 10 max. 2.30.1 Empty 240-280 min. (o80) (o330) 2.20.5 2.00.1 4.00.1 +0.1 2.1-0.05 Empty Components +0.1 o1.5 -0.0 Leader Cover Film 0.30.05 Trailer 40-190 1.750.1 Dimensions of carrier tape 16.00.2 Dimensions of Reel o13.00.2 17.51.5 21.50.5 User direction of feed (in mm) TPWKA Series Cover tape +0.1 o1.5 -0.0 8.00.1 10 max. 5.50.1 Chip filter 3 max. 16.00.2 1.950.1 The cover film peel strength force 0.1--0.7N 7.50.1 9.00.1 400-560 +0.1 1.75 -0.05 (o80) (o330) 2.20.5 Empty 240-280 min. 2.00.1 4.00.1 0.30.05 Empty Components +0.1 o1.5 -0.0 Leader Cover Film Trailer 40-190 Part Number marked side is always facing upside. 1.750.1 Dimensions of carrier tape Dimensions of Reel o13.00.2 17.51.5 21.50.5 User direction of feed (in mm) 14 39 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P25E3.pdf 01.10.17 Lead Type Packaging Lead Type Minimum Quantity Bulk : 500 pcs. Ammo Pack : 2000 pcs. (SFSRA/TPSRA series) 1500 pcs. (CDSRH/TPWRD/TPTRD series) SFSRA/TPSRA Series P2 P h h S M W1 W0 W L1 H0 W2 M D0 P1 F1 F2 P0 Item Lead length under the hole down tape t Direction Feed Code Dimensions L1 5.0 min. Tolerance Pitch of component P 12.7 0.5 Pitch of sprocket hole (I) P0 12.7 0.2 Length from hole center to lead P1 3.85 0.5 Length from hole center to component center P2 6.35 0.5 Lead spacing (I) F1 2.5 0.2 Lead spacing (II) F2 2.5 0.2 Slant to the forward or backward h 0 1.0 Slant to the left or right S 0 1.0 0.5 Width of carrier tape W 18.0 Width of hold down tape W0 6.0 min. Position of Sprocket hole W1 9.0 0.5 Gap of hold down tape and carrier Tape W2 0 +0.5 -0 Distance between the center of sprocket hole and lead stopper H0 18.0 0.5 Diameter of sprocket hole D0 o4.0 0.2 t 0.6 0.2 P020 254.0 1.5 Total tape thickness Pitch of sprocket hole (II) Remarks Tolerance for Pitches 10ZP0=1271 Hold down tape doesn't exceed the carrier tape. The pitch of 20 sprocket holes (in mm) 14 Continued on the following page. 40 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P25E3.pdf 01.10.17 Lead Type Packaging Continued from the preceding page. TPSRD/CDSRH_EK Series P2 h h P H0 W1 W0 W L1 W2 S1 D0 P1 F t P0 Item Code Dimensions Tolerance L1 3.0 min. ------ Pitch of component P 12.7 0.5 Pitch of sprocket hole (1) P0 12.7 0.2 Length from hole center to lead P1 3.85 0.5 Length from hole center to component center P2 6.35 0.5 Lead spacing F 5.0 +0.5 -0.2 Slant to the forward or backward h 0 1.0 Slant to the left or right S1 0 1.0 W 18.0 0.5 Width of hold down tape W0 6.0 min. ------ Position of sprocket hole W1 9.0 0.5 Gap of hold down tape and Carrier tape W2 0 +0.5 -0.0 Distance between the center of sprocket hole and lead stopper H0 18.0 0.5 Diameter of sprocket hole D0 o4.0 0.2 t 0.6 0.2 Po20 254.0 1.5 Lead length under the hole down tape Width of carrier tape Total tape thickness Pitch of sprocket hole (2) Remarks Hold down tape doesn't exceed the carrier tape The pitch of 20 sprocket holes (in mm) Continued on the following page. 14 41 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P25E3.pdf 01.10.17 Lead Type Packaging Continued from the preceding page. TPSRD_W/TPWRD/TPTRD/CDSRH_CK Series P2 h h P H0 W1 W0 W L2 L1 W2 S1 F1 F1 P1 D0 F t P0 Code Dimensions Lead Length under the Hold Down Tape Item L1 3.0 min. Tolerance Length of Cat off L2 2.0 max. Pitch of Components P 12.7 0.5 Pitch of Sprocket Hole (1) P0 12.7 0.2 To distinguish the direction Length from Hole Center to Lead P1 3.85 0.5 Length from Hole Center to Component Center P2 6.35 Pitch of the Terminal (1) F 5.0 Pitch of the Terminal (2) F1 2.5 0.5 +0.5 -0.2 0.2 Slant to the Forward or Backward h 0 1.0 Slant to the Left or Right S1 0 1.0 Width of Carrier Tape W 18.0 0.5 Width of Hold Down Tape W0 6.0 min. Position of Sprocket Hole W1 9.0 Gap of Hold Down Tape and Carrier Tape W2 0 0.5 +0.5 -0 Distance Between the Center of Sprocket Hole and Lead Stpper H0 18.0 0.5 Diameter of Sprocket Hole D0 o4.0 0.2 t 0.6 0.2 P020 254.0 1.5 Total Tape Thickness Pitch of Sprocket Hole (2) Remarks Must not protrude to the carrier tape The pitch of 20 sprocket holes (in mm) 14 42 Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. P25E3.pdf 01.10.17 Note: 1. Export Control For customers outside Japan Murata products should not be used or sold for use in the development, production, stockpiling or utilization of any conventional weapons or mass-destructive weapons (nuclear weapons, chemical or biological weapons, or missiles), or any other weapons. For customers in Japan For products which are controlled items subject to the "Foreign Exchange and Foreign Trade Law" of Japan, the export license specified by the law is required for export. < < > > 2. Please contact our sales representatives or product engineers before using our products listed in this catalog for the applications listed below which require especially high reliability for the prevention of defects which might directly cause damage to the third party's life, body or property, or when intending to use one of our products for other applications than specified in this catalog. q Aircraft equipment w Aerospace equipment e Undersea equipment r Power plant equipment t Medical equipment y Transportation equipment (vehicles, trains, ships, etc.) u Traffic signal equipment i Disaster prevention / crime prevention equipment o Data-processing equipment !0 Application of similar complexity and/or reliability requirements to the applications listed in the above 3. Product specifications in this catalog are as of September 2001. They are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before your ordering. If there are any questions, please contact our sales representatives or product engineers. 4. Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before your ordering. 5. Please note that unless otherwise specified, we shall assume no responsibility whatsoever for any conflict or dispute that may occur in connection with the effect of our and/or third party's intellectual property rights and other related rights in consideration of your using our products and/or information described or contained in our catalogs. In this connection, no representation shall be made to the effect that any third parties are authorized to use the rights mentioned above under licenses without our consent. 6. None of ozone depleting substances (ODS) under the Montreal Protocol is used in manufacturing process of us. http://www.murata.co.jp/products/ Head Office 2-26-10, Tenjin Nagaokakyo-shi, Kyoto 617-8555, Japan Phone:81-75-951-9111 International Division 3-29-12, Shibuya, Shibuya-ku, Tokyo 150-0002, Japan Phone:81-3-5469-6123 Fax:81-3-5469-6155 E-mail:intl@murata.co.jp