EZ-LIGHT(R) Touch K50 Series Illuminated Buttons Datasheet Lighted Touch Button with Bipolar Outputs For the latest technical information about this product, including specifications, dimensions, and wiring, see www.bannerengineering.com. * * * * * * * Rugged, cost-effective, and easy-to-install touch button with multicolor light Momentary versions remain activated as long as touch is present Latching versions start up not activated and toggle between activated and not activated on successive touches Waterproof IP69K construction for washdown environments Ergonomically designed to eliminate hand, wrist, and arm stresses associated with repeated switch operation; require no physical force to operate Can be actuated with bare hands or in gloves 12 to 30V dc operation Models Model 1 Function K50ALBTXGHQ K50RLBTXGHQ K50ABTXGHQ K50RBTXGHQ K50ALBTGGHQ K50RLBTGGHQ K50ABTGGHQ K50RBTGGHQ K50ALBTRGHQ K50RLBTRGHQ K50ABTRGHQ K50RBTRGHQ Latching Momentary Latching Momentary Latching Momentary Output Light (not activated) Light (activated) - Green Green Green Red Green Connection Bipolar, N.O. Bipolar, N.C. Bipolar, N.O. Bipolar, N.C. Bipolar, N.O. Bipolar, N.C. Bipolar, N.O. Integral 5-pin Euro QD Bipolar, N.C. Bipolar, N.O. Bipolar, N.C. Bipolar, N.O. Bipolar, N.C. WARNING: Not To Be Used for Personnel Protection Never use this device as a sensing device for personnel protection. Doing so could lead to serious injury or death. This device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-energized sensor output condition. 1 5-pin integral QD models only are listed. * For 5-pin 150 mm (5.9 in) Eurostyle PVC pigtail, replace suffix Q with QP in model number (example, K50ALBTXGHQP). * For 2 m (6.5 ft) cable, omit suffix Q from model number (example, K50ALBTXGH). * A model with a QD requires a mating cable (see Cordsets on page 3). P/N 166767 Rev. D 7 November 2013 0 166767 7 EZ-LIGHT(R) Touch K50 Series Illuminated Buttons Specifications Supply Voltage 12 to 30 V dc Environmental Rating IEC IP67, IP69K per DIN 40050-9. Cabled models also meet IP69K if the cable and cable entrance are protected from high-pressure spray. Supply Current < 75 mA max current at 12 V dc (exclusive of load) < 50 mA max current at 30 V dc (exclusive of load) Supply Protection Circuitry Protected against reverse polarity and transient voltages Output Rating Maximum Load: 150 mA On-state saturation voltage: < 2V at 10 mA dc; < 2.5V at 150 mA dc Off-state leakage current <10 A at 30 V dc Output Response Time Momentary models: 50 milliseconds On and Off Latching models: 150 milliseconds On and Off Operating Conditions Temperature: -40 C to +50 C (-40 F to +122 F) Humidity: 90% at 50 C max. relative humidity (non-condensing) Storage -40 C to +70 C (-40 F to +158 F) Construction Housing: polycarbonate Translucent dome: polycarbonate Mounting Nut: PBT Mounting M30 x 1.5 Threaded base Max torque 4.5 Nm (40in lb f) Vibration and Mechanical Shock All models meet Mil. Std. 202F requirements method 201A (vibration: 10 to 60 Hz max., double amplitude 0.06 in. maximum acceleration 10G). Also meets IEC 947-5-2; 30G 11 ms duration, half sine wave. Power-Up Device requires 300 milliseconds to start up Latching models startup in not activated state Connections 5-pin integral Euro-style QD, 2 m (6.5 ft) PVC integral cable, or 5pin 150 mm (5.9 in) Euro-style PVC pigtail QD Certifications Dimensions Wiring Diagram Bipolar Color Key: 1 + 12-30V dc - 3 2 4 5 2 Load Load 1 2 3 4 5 = = = = = Brown White Blue Black Gray Not Used www.bannerengineering.com - tel: 763-544-3164 P/N 166767 Rev. D EZ-LIGHT(R) Touch K50 Series Illuminated Buttons Accessories Cordsets 5-Pin Threaded M12/Euro-Style Cordsets (Single Ended) Model Length MQDC1-501.5 0.50 m (1.5 ft) Style MQDC1-506 1.83 m (6 ft) MQDC1-515 4.57 m (15 ft) MQDC1-530 9.14 m (30 ft) MQDC1-506RA 1.83 m (6 ft) MQDC1-515RA 4.57 m (15 ft) Dimensions 2 44 Typ. 1 3 Straight 4 M12 x 1 o 14.5 5 1 2 3 4 5 32 Typ. [1.26"] = = = = = Brown White Blue Black Gray 30 Typ. [1.18"] Right-Angle MQDC1-530RA Pinout (Female) 9.14 m (30 ft) M12 x 1 o 14.5 [0.57"] Brackets SMB30A * Right-angle bracket with curved slot for versatile orientation * Clearance for M6 (1/4 in) hardware * Mounting hole for 30 mm sensor * 12-ga. stainless steel 45 C 61 B A 69 Hole center spacing: A to B=40 Hole size: A=o 6.3, B= 27.1 x 6.3, C=o 30.5 SMB30FA * Swivel bracket with tilt and pan movement for precise adjustment * Mounting hole for 30 mm sensor * 12-ga. 304 stainless steel * Easy sensor mounting to extrude rail T-slot * Metric and inch size bolt available 83.2 36.3 68.9 B A Bolt thread: SMB30FA, A= 3/8 - 16 x 2 in; SMB30FAM10, A= M10 1.5 x 50 Hole size: B= o 30.1 SMB30FVK * V-clamp, flat bracket and fasteners for mounting to pipe or extensions * Clamp accommodates 28 mm dia. tubing or 1 in. square extrusions * 30 mm hole for mounting sensors Hole size: A= o 31 P/N 166767 Rev. D 46 A 118 SMB30MM * 12-ga. stainless steel bracket with curved mounting slots for versatile orientation * Clearance for M6 (1/4 in) hardware * Mounting hole for 30 mm sensor 57 70 C 57 B A Hole center spacing: A = 51, A to B = 25.4 Hole size: A = 42.6 x 7, B = o 6.4, C = o 30.1 www.bannerengineering.com - tel: 763-544-3164 3 EZ-LIGHT(R) Touch K50 Series Illuminated Buttons SMB30RAVK * V-clamp, right-angle bracket and fasteners for mounting sensors to pipe or extrusion * Clamp accommodates 28 mm dia. tubing or 1 in. square extrusions * 30 mm hole for mounting sensors A 46 90 57 Hole center spacing: A=26.0, A to B=13.0 Hole size: A=26.8 x 7.0, B=o 6.5, C=o 31.0 67 B 58 29 A Hole center spacing: A=o 50.8 Hole size: A=o 7.0, B=o 30.0 Hole size: A = o 30.5 SMBAMS30P * Flat SMBAMS series bracket * 30 mm hole for mounting sensors * Articulation slots for 90+ rotation * 12-ga. 300 series stainless steel SMB30SC * Swivel bracket with 30 mm mounting hole for sensor * Black reinforced thermoplastic polyester * Stainless steel mounting and swivel locking hardware included 45 C 93 A B SMBAMS30RA * Right-angle SMBAMS series bracket * 30 mm hole for mounting sensors * Articulation slots for 90+ rotation * 12-ga. (2.6 mm) cold-rolled steel 45 C 53 A B 48 Hole center spacing: A=26.0, A to B=13.0 Hole size: A=26.8 x 7.0, B=o 6.5, C=o 31.0 Banner Engineering Corp. Limited Warranty Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product. THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE. This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE. Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp. www.bannerengineering.com - tel: 763-544-3164