D11000PS DIFFERENTIAL PROBE SYSTEM
www.lecroy.com 237
PROBES AND
PROBE ACCESSORIES
PROBES AND PROBE ACCESSORIES
The D11000PS extends the full signal acquisition performance of the SDA 11000 and
SDA 9000 to the probe tips. With 11 GHz system bandwidth, the probe enables direct
measurement of high-speed serial data streams up to 6.25 Gb/s. The D11000PS also
provides 11 GHz system bandwidth when used with the SDA 18000.
Choice of Interconnect Styles Without Compromising Performance
The D11000PS provides both direct Solder-In and cabled SMA interconnect lead
assemblies. Each interconnect lead comes with a dedicated probe amplifier module
that has calibration data optimized for the respective lead. This eliminates the
performance compromise of using a single calibration for multiple lead types. The
Solder-In lead provides the highest possible signal integrity with a high loading
impedance. The dual SMA interconnect leads provide a true differential 50 Ωinput.
This is a convenient alternative to direct cabling into the oscilloscope inputs, freeing
up the second channel for other signal input, and eliminating the need to set up
waveform math and match cable delays.
Unsurpassed Waveform Accuracy
When used to acquire input signals for the SDA 11000, SDA 9000, or SDA 18000, the
D11000PS provides unprecedented waveform fidelity, even with signals at higher
serial data rates. The D11000PS utilizes third generation compensation calibration,
the most advanced in use today, to provide optimal system response.
Each individual probe is characterized with this system. Information on the probe’s
frequency and time domain responses are stored in non-volatile memory within
the probe amplifier module. This information is uploaded to the higher bandwidth
SDA’s when the probe is connected. The probe calibration data and the SDA
oscilloscope’s calibration data combine to generate new equalization filters for
the composite system. The resulting compensation system corrects for frequency
response deviations, as well as group delay correction and reflection cancellation.
D11000PS DIFFERENTIAL PROBE SYSTEM
238 1-800-5-LeCroy
PROBES AND
PROBE ACCESSORIES
Reproducing accurate serial data eye patterns requires maintaining precise magnitude
and phase relationships between the fundamental and the odd harmonics. The advanced
calibration system used in the D11000PS assures the best eye pattern fidelity.
Superior Probe Loading Characteristics
Accurate frequency response is not enough to assure good waveform fidelity.
Excessive probe loading can cause waveform distortion. The D11000PS continues
the legacy of LeCroy high-performance probe design, placing special emphasis on
minimizing loading of the circuit under test.
The Solder-In lead and dedicated probe amplifier module have a high input resistance
at DC and low frequencies, allowing the probe to be used in circuits which cannot
drive the low resistance of a pure transmission line probe. The direct cabled SMA
inputs have 50 Ωinput impedance with low VSWR.
Ease of Use
Attention to fine details during the D11000PS design process has resulted in several
“ease of use” features. A common mode measure feature allows the user to measure
the average common mode component with a single click in the probe control menu.
AutoColor ID lights an indicator in the probe body, matching the color of the waveform
trace. When multiple channels are used, this feature instantly identifies which wave-
form corresponds to which probe.
Several connection accessories designed specifically for the D11000PS provide
convenient and secure mounting of the probe body and Solder-In tip to the test circuit.
DC blocking adapters extend the common mode range of the SMA cabled input for
use with higher common mode voltages such as Digital Video Interface (DVI). A finger
wrench allows tightening of SMA connectors on dense test fixtures.
D11000PS DIFFERENTIAL PROBE SYSTEM
www.lecroy.com 239
PROBES AND
PROBE ACCESSORIES
Compatibility
The D11000PS is designed specifically for use with the SDA 11000, SDA 9000, or
SDA 18000. However, it does contain additional calibration data for use with all
of the lower bandwidth WaveMaster, SDA, and DDA 5005A Series oscilloscopes
and analyzers.
SPECIFICATIONS
Bandwidth, System, -3 dB 11 GHz (Typical)*
Rise Time, System < 50 ps (Typical)*
Rise Time, Probe only < 40 ps
Attenuation, Nominal ÷3
LF Attenuation Accuracy 2% (20–30 ˚C)
Output Zero < 15 mV referred to input
Noise, System 5 mV rms (Typical)1
Differential Mode Range ±1 V
Common Mode Range ±4 V, Solder-In tip
±2 V, SMA cable input†
Input Resistance at DC, 40 kΩdifferential
(Solder-In lead) 20 kΩeach side to ground
Minimum Input Impedance, > 175 Ω
(Solder-In lead, to 11 GHz) (Refer to graph)
Input Impedance, (SMA cable input) 50 Ω
Input VSWR, < 1.5:1 DC–6 GHz
(Typical, each lead to ground) < 2.0:1 6 GHz–11 GHz
CMRR, > 40 dB DC–1 GHz
(Typical) > 30 dB 1 GHz–4 GHz
> 20 dB 4 GHz–11 GHz
* Measured as a system with SDA 11000, SDA 9000 and SDA 18000.
†Can be extended by using DC Blocking Adapters.
PROBES AND PROBE ACCESSORIES
D11000PS DIFFERENTIAL PROBE SYSTEM
240 1-800-5-LeCroy
PROBES AND
PROBE ACCESSORIES
D11000PS Includes:
Probe amplifier modules (2–1 each for SMA input and Solder-In lead), Solder-In lead
assembly (2), SMA interconnect lead, SMA input cables (matched pair), Probe body,
SMA DC blocking adapters (2), ground lead and clip, SMA finger wrench (2), tip
retaining clip kit for Solder-In lead, probe body mounting clamp set, FreeHand probe
stand, ESD dissipating wrist strap, SAC-01 soft accessory case with insert, small
accessory case, D11000PS Instruction Manual, certificate of traceable calibration.
ORDERING INFORMATION PRODUCT CODE
Differential Probe System D11000PS
Replacement Solder-In Tip Assembly D11000SI
NIST Traceable Calibration with Test Data D11000PS-CCNIST
(one module)
D500PT
D350ST
D600ST
D300A-AT
D600A-AT
WAVELINK DIFFERENTIAL PROBES
www.lecroy.com 241
PROBES AND
PROBE ACCESSORIES
PROBES AND PROBE ACCESSORIES
WaveLink high bandwidth differential probes are designed to provide an optimum
mechanical connection for signal measurement. They virtually eliminate distortion
when measuring signals, which is particularly useful in eye pattern measurements—
now routine for systems using fast serial data bus architecture. WaveLink probes
provide industry-leading technology for wideband signal connection to test instruments.
The first differential probes to employ SiGe technology, they deliver full system bandwidth
when used with LeCroy 6 GHz, 5 GHz, and 3 GHz instruments. They are also the first
differential probes to use a unique calibration process to achieve superb waveform
fidelity for routine voltage measurements.
Features:
•Unique adjustable tips for reliable contact
•Wide assortment of small tips ideal for restricted spaces
•Best-in-class probe loading for accurate signal measurement
•Superior loading characteristics and precise frequency response
•Outstanding fidelity for high-speed signals
D600A-AT and D300A-AT Features:
•Built-in thumbwheel for precise positioning of tip; stays put after adjustment
•Maintains sharp points for good contact
•Tips made of “NiTiNOL,” a super-elastic nickel-titanium alloy
•Probe flexes as you apply pressure and consistently returns to original form
D600ST and D350ST Features:
•Best-in-class mechanical design for optimum utility
•Small tip high bandwidth differential probe
•Three interconnect configurations for flexibility
•Very small form factor for accessing tight spaces
•Highly flexible long lead
•Inexpensive and easily replaceable
D500PT Positioner Mounted Tip Features:
•Positioned tip assembly
•Very small tip geometry for accessing physically constrained locations
•Ideal for applications requiring multiple probes on adjacent pads
•Telescoping tips for reliable tip contact—even when probe it tilted
•Mounts in probe positioner or can be hand held
•EZ-Probe positioner available as an accessory
WaveLink D600ST and D350ST
Best-in-class mechanical design for optimum utility:
•Small tip, high bandwidth differential probe
•Three interconnect configurations for flexibility
•Very small form factor for accessing tight spaces
Each of the interchangeable leads is a thin, highly
flexible 145 mm (5.7") long lead connecting the tip
and the D600ST/D350ST probe tip module.
WAVELINK DIFFERENTIAL PROBES
242 1-800-5-LeCroy
PROBES AND
PROBE ACCESSORIES
FLEXIBLE INTERCONNECTION OPTIONS —WITHOUT SACRIFICING PERFORMANCE
D500PT Positioner Mounted
Probe Tip Module
The probe has a very thin form factor,
allowing multiple probes to be used
when several channels are required
to monitor signals from the same small
IC. It has 2 mm of Z-axis compliance
through spring-loaded telescoping tips,
allowing considerable angular freedom
relative to the circuit board while still
maintaining reliable contact with both
inputs. A ball joint between the tip
and mounting arm makes it even easier
to adjust for placement when already
mounted in a positioner. A small
thumbscrew allows precise and
secure adjustment of the tip spacing.
D600A-AT and D300A-AT
Adjustable Tips
WaveLink adjustable tip probes are
designed to provide an optimum
mechanical connection for signal
measurement.
•Built-in thumbwheel for precise
positioning of tip—stays put
after adjustment
•Maintains sharp points for
good contact
•Tips made of “NiTiNOL,” a super-
elastic nickel-titanium alloy
•Flexes as you apply pressure
• Consistently returns to original form
EZ-Probe Positioner
The EZ-Probe positioner provides
stable, accurate positioning in the
x-y-z axis. Ideal for use with the
D500PT and D600A-AT/D300A-AT
probe tips. The unique, 3:1 motion
reduction joystick allows simple,
precise positioning of the attached
probe in both the horizontal and
vertical measuring plane. The
probe has a fully articulating arm,
providing 30 cm (12") reach in virtually
any direction.
The Probe Tip Modules contain the active amplifier
circuitry. Different modules have different electrical
and physical inter connect characteristics, allowing
the user to select the module appropriate for the
application.
WAVELINK DIFFERENTIAL PROBES
www.lecroy.com 243
PROBES AND
PROBE ACCESSORIES
PROBES AND PROBE ACCESSORIES
THREE DIFFERENT TIPS FOR INTERCONNECT FLEXIBILITY
Solder-In Lead
The Solder-In interconnect lead
features the smallest physical tip size
of any high bandwidth differential
probe and the highest level of
electrical performance. Two very
small damping resistors are directly
soldered into the connect points
providing a reliable, intermittent free
electrical connection. The resistors
have highly flexible leads allowing
connection to input points with a
wide range of input spacing.
Quick Connect (D600ST only)
The Quick Connect inter connect
lead enables you to quickly move
the probe between multiple test
points on the test circuit. Just solder
a pair of damping resistors at each
location where interconnection is
required. A small connector mounted
on the probe tip, plugs into the damping
resistors, letting you quickly move
between sets of test points.
Square Pin
Many applications, such as IC
characterization boards, use
standard 0.025" square pins for
interconnect. The Square Pin
interconnect lead directly mates
with a pair of 0.025" (0.635 mm)
square pins which are mounted on
standard 0.100" (2.54 mm) centers.
SPECIFICATIONS
Rise Time, probe only
D600A-AT < 70 ps*
D600ST-SI < 65 ps*
D500PT < 100 ps†
D300A-AT < 95 ps‡
D350ST-SP < 90 ps‡
LF Attenuation Accuracy (with 0 V common mode)
D600A-AT, D300A-AT, 2% 0 ±1.2 V
D600ST, and D500PT 5% ±1.2 V ±2.4 V
D350ST 2% 0 ±2.5 V
5% ±2.5 V ±5 V
Output Zero
(within 15 minutes after Autozero)
D600A-AT, D300A-AT, < 10 mV RTI
D600ST, and D500PT
D350ST < 20 mV RTI
Bandwidth, System DC to -3 dB (Typical)
D600ST-SI 6 GHz**
D600ST-QC 4 GHz**
D600ST-SP 3 GHz**
D600A-AT 6 GHz**
D300A-AT 3 GHz††
D350ST-SP 3 GHz††
D350ST-SI 3 GHz††
D500PT 5 GHz†
Input Dynamic Range
D600A-AT, D300A-AT, ±2.4 V
D600ST, and D500PT
D350ST ±5 V
Common Mode Range
(Max. peak voltage either input to ground)
D600A-AT, D300A-AT, ±2.4 V
D600ST, and D500PT
D350ST ±5 V
DC Input Resistance
D600A-AT, D300A-AT, 4 kΩ differential
D600ST, and D500PT 2 kΩ either input to ground
D350ST 8 kΩ differential
4 kΩ either input to ground
*Measured with 6 GHz or greater oscilloscope
†Measured with 5 GHz oscilloscope
‡Measured with 3 or 4 GHz oscilloscope
**Typical, with 6 GHz or greater oscilloscope
††Typical, with 3 or 4 GHz oscilloscope
WAVELINK DIFFERENTIAL PROBES
244 1-800-5-LeCroy
PROBES AND
PROBE ACCESSORIES
WAVELINK DIFFERENTIAL PROBES
www.lecroy.com 245
PROBES AND
PROBE ACCESSORIES
PROBES AND PROBE ACCESSORIES
SPECIFICATIONS (CONTINUED)
CMRR
D600A-AT
DC to 1 GHz > 40 dB
1 GHz to 3 GHz > 30 dB
3 GHz to 7 GHz > 20 dB
D600ST
DC to 1 GHz > 30 dB
1 GHz to 3 GHz > 25 dB
3 GHz to 7 GHz > 20 dB
D500PT
DC to 1 GHz > 25 dB
1 GHz to 3 GHz > 19 dB
3 GHz to 5 GHz > 16 dB
D350ST
DC to 1 GHz > 30 dB
1 GHz to 3 GHz > 25 dB
D300A-AT
DC to 1 GHz > 40 dB
1 GHz to 3 GHz > 30 dB
Noise
D600A-AT, D600ST, D500PT 5.8 mVrms with 6 GHz oscilloscope
D300A-AT 5.0 mVrms with 3 GHz oscilloscope
D350ST 9.5 mVrms with 3 GHz oscilloscope
ORDERING INFORMATION PRODUCT CODE
PROBE TIP MODULES
WaveLink 7.5 GHz, Differential Probe Adjustable Tip Module D600A-AT*
WaveLink 4 GHz, Differential Probe Adjustable Tip Module D300A-AT*
WaveLink 7 GHz, Differential Probe Small Tip Module D600ST*
WaveLink 4 GHz, 5 V Differential Probe Small Tip Module D350ST*
WaveLink 6 GHz, Differential Positioner D500PT*
Mounted Tip Module
PROBE BODIES
WaveLink ProLink Probe Body WL600
WaveLink ProBus Probe Body WL300
POSITIONER
Cascade Microtech EZ-Probe Positioner EZ PROBE
SERVICE OPTIONS
NIST Traceable Calibration with Test Data†D600A-AT-CCNIST
(one module) D300A-AT-CCNIST
D600ST-CCNIST
D350ST-CCNIST
D500PT-CCNIST
* For a complete probe, order a WL300 or WL600 Probe Body with Probe Tip Module.
†-CCNIST NIST traceable calibration with test data is an available option for D600ST, D350ST, D500PT, D600A-AT, or
D300A-AT probe tip module only when ordered with either a WL600 or WL300 probe body.
WAVELINK DIFFERENTIAL PROBES
246 1-800-5-LeCroy
PROBES AND
PROBE ACCESSORIES
ORDERING INFORMATION (CONTINUED) PRODUCT CODE
CONSUMABLES AND REPLACEMENT PARTS
Replacement Quick Connect Lead Set for D600ST D600ST-QC
Replacement Solder-In Lead Set for D600ST D600ST-SI
Replacement Square Pin Lead Set for D600ST D600ST-SP
Extra Solder-In Lead for D350ST D350ST-SI
Extra Square Pin Lead for D350ST D350ST-SP
Replacement Tip Assembly for D500PT D500PT-TIP
Replacement Resistor Kit for D600ST-SI (10) PK600ST-1
Replacement Resistor Kit for D600ST-QC (20) PK600ST-2
Replacement Probe Tip Holder Kit PK600ST-3
Replacement Probe Body Mounting Kit PK600ST-4
Replacement Probe Tips for D500PT (pkg. of 4) PK500PT-1
Replacement Resistor Kit for D350ST-SI (10) PK350ST-1
Probe Characterization Fixture PCF-200
WaveLink Probe Series Instruction Manual WL-OM-E
D600A-AT, D300A-AT Adjustable Tip Modules Include:
Protective storage case, ground wire and clip, WaveLink Series instruction
manual, Quick Start guide, calibration certificate.
D600ST Small Tip Module Includes:
Solder-In interconnect lead set with replacement damping resistors (10), Quick
Connect interconnect lead set with additional damping resistors (20), Square Pin
interconnect lead set, ground wire and clip, probe tip mounting kit, WaveLink
Series instruction manual, Quick Start guide, calibration certificate.
D350ST Small Tip Module Includes:
Solder-In interconnect lead set with replacement damping resistors (10), Square
Pin interconnect lead set, ground wire and clip, probe tip mounting kit, WaveLink
Series instruction manual, Quick Start guide, calibration certificate.
D500PT Positioner Mounted Tip Includes:
Positioned tip assembly, Probe tip module, Module mounting clamp, Ground
lead and clip, WaveLink Series instruction manual, Quick Start guide, Calibration
certificate, FreeHand probe stand, Tip repair tool, Replacement tips (2)
WL600, WL300 Probe Bodies Include:
SAC-01 Soft accessory case with WaveLink Series insert, probe character ization
fixture, probe body mounting clip, probe cable clamp (2), and small probe acces-
sory case.
WaveLink Probe Calibration
When ordered with WL600 or WL300 also substitute: Certificate of NIST traceable
calibration in place of calibration certificate.
Maximum Recommended
Model Bandwidth Input R Input C Attenuation Voltage Diameter Oscilloscope
PP005A 500 MHz 10 MΩ11 pF 10:1 500 V 5 mm 1, 2, 12, 13
PP006A 500 MHz 10 MΩ12 pF 10:1 600 V 5 mm 3, 11
PP007-WS 500 MHz 10 MΩ9.5 pF 10:1 400 V 2.5 mm 4
PP007-WR 500 MHz 10 MΩ9.5 pF 10:1 400 V 2.5 mm 5, 7, 9
PP008 500 MHz 10 MΩ9.5 pF 10:1 400 V 2.5 mm 4, 6, 8
PP009 500 MHz 10 MΩ9.5 pF 10:1 400 V 5 mm 4, 6, 8
PP010 200 MHz 10 MΩ12.5 pF 10:1 600 V 5 mm 10
PP011 500 MHz 10 MΩ9.5 pF 10:1 400 V 5 mm 5, 7, 9
Recommended Oscilloscope
1 9300 Series 8 WaveSurfer Xs Series (≤600 MHz)
2 LC Series 9 WaveSurfer Xs Series (1 GHz)
3 LT Series 10 WaveJet Series (≤200 MHz)
4 WaveSurfer 400 Series 11 WaveJet Series (≥350 MHz)
5 WaveRunner 6000 Series 12 WavePro 900 Series
6 WaveRunner Xi Series (≤600 MHz) 13 WavePro 7000 Series
7 WaveRunner Xi (1 GHz–2 GHz)
ORDERING INFORMATION PRODUCT CODE
÷10, 500 MHz 10 MΩ Passive Probe PP005A
÷10, 500 MHz 10 MΩ Passive Probe PP006A
÷10, 500 MHz 10 MΩ Passive Probe PP007-WS-1
÷10, 500 MHz 10 MΩ Passive Probe PP007-WR-1
÷10, 500 MHz 10 MΩ Passive Probe PP008
÷10, 500 MHz 10 MΩ Passive Probe PP009
÷10, 200 MHz 10 MΩ Passive Probe PP010
÷10, 500 MHz 10 MΩ Passive Probe PP011
PASSIVE PROBES
248 1-800-5-LeCroy
PROBES AND
PROBE ACCESSORIES
Passive probes are the standard probe provided with most oscilloscopes. Typical
passive probes provide a 10:1 attenuation and feature a high input resistance of
10 MΩ. This high input resistance means that passive probes are the ideal tool for
low frequency signals since circuit loading at these frequencies is minimized. Passive
probes are designed to handle voltages of at least 400 V, some as high as 600 V.
LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope
to scale the waveforms automatically requiring no user input.
Each passive probe is recommended for a certain oscilloscope, using the right
passive probe with the right oscilloscope means that the probe can be properly
compensated across the entire bandwidth. Using probes with a different oscilloscope
will only let you compensate for low frequencies.
Features:
•Bandwidth from 200 MHz to 500 MHz
•Probe encoding ring for automatic scale factor readout on LeCroy oscilloscopes
WAVELINK DIFFERENTIAL PROBES
www.lecroy.com 247
PROBES AND
PROBE ACCESSORIES
PROBES AND PROBE ACCESSORIES
WAVELINK PROBE COMPATIBILITY CHART
• Recommended
NC Not Compatible
FP Operates at Full Performance
RP Operates with Reduced Performance with
LPA adapters. Frequency response > 3 GHz
may be altered
RP1Operates with Reduced Performance with
LPA adapters. Frequency response > 3 GHz
may be altered
WR 204Xi
SDA 18000* WR 104Xi
SDA 11000* WR 64Xi
SDA 9000* WP7300A WR 62Xi
SDA 6020 WM8620A WP7200A WR 44Xi
SDA 4020 WM8420A DDA 5005A DDA 3000 WP7100A WR 6KA WL300 WL600
D600A-AT • • • RP FP
D300A-AT • • • FP FP
D600ST • • • RP FP
D350ST • • • • • • FP FP
D500 PT • • • • • • RP FP
WL600 • • • NC NC NC
WL300 RP1RP1RP1•••
*
Operates on channels in 6 GHz mode only
PASSIVE PROBES ACCESSORIES
www.lecroy.com 249
PROBES AND
PROBE ACCESSORIES
ORDERING INFORMATION PRODUCT CODE
PK001 – Standard Probe Accessory for PP002
Ground Lead PP002 PP001/002-1
Probe Tip to BNC adapter PP001/002-2
Sprung Hook PP002 PP001/002-3
M/F Lead – Long (4")
M/F Lead – Short (2")
PK102 – Standard Probe Accessory Kit for PP005/PP005
Sprung Hook (Black) PP005-HOOK
Spring Tip (0.38 mm) PP005-ST38
Spring Tip (0.8 mm) PP005-ST8
Rigid Tip (0.8 mm) PP005-RT
Probe Tip to BNC Adapter PP005-BNC
Ground Lead (11 cm) PP005-GL11
Ground Lead (22 cm) PP005-GL22
Ground Lead (Spring) PP005-GLPT
IC Insulating Tip
Probe Tip to BNC Adapter
Adjustment Screw Driver
PPK106 – SMT Accessories for PP005/PP005A, PPExkV
Dual Lead Adapter PK106-1
Single Lead Adapter PK106-2
0.5 mm Clip (Orange) PK106-3
Probe Tip to PCB Adapter PK106-4
M/F Lead – Long (4") PK106-5
M/F Lead – Short (2") PK106-6
0.5 mm Clip (Yellow) PK106-8
PK101 – Microclip Accessory Kit for PP005/PP005A
Single Lead Adapter PK106-2
QFPIC Clip (0.5 mm Pitch) PACC-CL001
PK116 – Standard Probe Accessory Kit for PP006/PP006A
Sprung Hook PK116-1
Ground Lead PK116-2
Ground Pin PK116-3
Insulating Tip
Screw Driver
PK006 – SMT Accessories for PP006/PP006A
Dual Lead Adapter PK006 PK006-1
Single Lead Adapter PK006 PK006-2
0.5 mm Clip (Black and Red) PK006-3
0.8 mm Clip (Black and Red) PK006-4
M/F Lead – Long (4")
M/F Lead – Short (2")
PROBES AND PROBE ACCESSORIES
PASSIVE PROBES ACCESSORIES
250 1-800-5-LeCroy
PROBES AND
PROBE ACCESSORIES
ORDERING INFORMATION PRODUCT CODE
PKIT1-5MM-102 – Basic Adapter Kit for PP009
Sprung Hook PK1-5MM-101
Standard Ground Lead PK1-5MM-102
Adjustment Tool PK1-5MM-103
Rigid Tip, 0.8 mm PK1-5MM-104
IC Cap, 2.54 mm pitch PK1-5MM-108
Spring Tip 0.8 mm (Qty. 6) PK1-5MM-109
BNC Adapter PK1-5MM-110
Adapter, 4 mm plug PK1-5MM-117
Ground Spring PK1-5MM-118
High Frequency Compensated Ground Lead PK1-5MM-123
Spring Tip 0.38 mm (Qty. 5) PK1-5MM-124
PKIT1-5MM-101 – Micro Clip Kit for PP009
Single Lead Adapter PK1-5MM-111
Microclip Long, Green PK1-5MM-114G
Microclip Long, Yellow PK1-5MM-114Y
Microclip Short, Green PK1-5MM-115G
Microclip Short, Yellow PK1-5MM-115Y
PKIT2-5MM-101 – Standard Accessory Kit for PP010
Sprung Hook PK2-5MM-101
Standard Ground Lead PK2-5MM-102
Adjustment Tool
Ground Attachment
IC Test Tip
Color Coding Rings (set)
PROBES AND
PROBE ACCESSORIES
PROBES AND PROBE ACCESSORIES
PK1-5MM-108
IC-Cap 5.0
2.54 mm pitch; black
PK1-5MM-107
PCB Adapter 5.0
PK1-5MM-109
Spring Tip 0.8 mm
PK1-5MM-118
Ground Spring 5.0
PK1-5MM-123
HF Compensated Ground Lead 22 cm
PK1-5MM-102
Ground Lead 11 cm
PK1-5MM-122
Ground Lead 22 cm to 4 mm banana plug
PK1-5MM-121
Ground Lead 22 cm to 2 mm banana plug
PK1-5MM-119
Ground Lead 11 cm to miniclip
PK1-5MM-120
Ground Lead 11 cm to 0.8 mm plug
PK1-5MM-117
Flexible Adapter 5.0 to 4 mm banana plug
PK1-5MM-116
Flexible Adapter 5.0 to 2 mm banana plug
PK1-5MM-111
Adapter 5.0 to 0.8 mm socket
PK1-5MM-112
Dual Adapter 5.0 to 0.8 mm socket
PK1-5MM-114Y, PK1-5MM-114G
QFP IC-Clip 13 mm long
down to 0.5 mm pitch
( X : 4 = yellow; 5 = green )
PK1-5MM-115Y
PK1-5MM-115G
QFP IC-Clip short
down to 0.5 mm pitch
( X : 4 = yellow; 5 = green )
PK1-5MM-113
Pico hook \U+2122
PK1-5MM-106
Set Coding Rings
3x4 colors
PK1-5MM-124
Spring Tip 0.38 mm
PK1-5MM-101
Sprung Hook II 5.0
black
Protection Cap 5.0
black
PK1-5MM-103
Adjustment Tool
PK1-5MM-110
BNC Adapter 5.0
0.4 [0.02"]
4 [0,16"]
3.5 [0.14"]
4.2 [0.17"]
2 [0,08"]
PK1-5MM-105
Insulating Cap
Passive Probe Accessories PP005, PP009, and PP011 Series
PK1-5MM-104
Rigid Tip 0.8 mm
www.lecroy.com 251
PP008-1
PP007-WS-1
PP007-WR-1
PASSIVE PROBES
252 1-800-5-LeCroy
PROBES AND
PROBE ACCESSORIES
The PP007 and PP008 embody leading edge technology in passive probe design.
A rugged, general-purpose probe, its small size is optimized for maximum waveform
fidelity. The small 2.5 mm ground sleeve provides superior visibility, as well as a
greater ability to probe dense circuits than traditional 3.5 mm and 5 mm probes.
Its sharp probe tip* is spring loaded, allowing it to retract into the narrow probe
head. Low input capacitance and low inductance optimize functionality in high
frequency applications. For best performance, the PP007-WR-1 version is designed
to be used with the WaveRunner 6000A Series, while the PP007-WS-1 version is
designed for the WaveSurfer 400 Series. The PP008-1 is designed for use with the
WaveRunner Xi Series.
Features:
•Compact probe head
•Fine pitch SMD probing support
•Rugged, sharp tip
•HF optimized connection accessories
•Over 30 accessories
•Low input capacitance
SPECIFICATIONS
ELECTRICAL CHARACTERISTICS
Attenuation ÷ 10
Bandwidth > 500 MHz
Input R 10 MΩ
Input C 9.5 pF
Max. Input 400 V CAT I
Voltage (1250 V surge) 300 V CAT II
GENERAL CHARACTERISTICS
Ground Sleeve Diameter 2.5 mm
Input Pin Diameter 0.5 mm
Cable Length 1.3 m
ORDERING INFORMATION PRODUCT CODE
Basic Adapter Kit PK701
Advanced Adapter Kit PK702
SMD Adapter Kit PK703
Microclip Kit PK704
÷10 HiZ 500 MHz Passive Probe PP008-1
for WaveRunner Xi Series Oscilloscopes
÷10 HiZ 500 MHz Passive Probe PP007-WR-1
for WaveRunner 6000A Series Oscilloscopes
÷10 HiZ 500 MHz Passive Probe PP007-WS-1
for WaveSurfer 400 Series Oscilloscopes
Instruction Manual PP007-OM-E
* A rigid tip is included
5,8 [0,228]
1 [0,039]
1,5 [0,059]
PK007-031
BNC Adapter
PK007-003
Adjustment T ool
PK007-007
Insulating Cap
PK007-012
IC Cap
1.27 mm pitch
(black)
PK007-011
IC Cap
1.0 m m pitch
(brown)
PK007-010
IC Cap
0.8 mm pitch
(gray)
PK007-009
IC Cap
0.65 mm pitch
(blue)
PK007-008
IC Cap
0.5 mm pitch
(green)
Protection Cap
PK007-015
PCB Adapter
PK007-005
Spring Tip 0.5 mm
PK007-004
Rigid Tip 0.5 mm
PK007-016
Ground Spring
PK007-013
Ground Blade
PK007-025
Probe Tip Ground Lead
with Alligator Clip
PK007-024
Probe Tip Ground Lead
with 0.8 mm Socket
PK007-014
10 Copper Pads
( 2 x 2 cm )
PK007-030
High Frequency Compensated Ground Lead
PK007-002
Standard Ground Lead
PK007-029
Ground Lead with 4 mm plug
PK007-028
Ground Lead with 2 mm plug
PK007-026
Ground Lead with mini clip
PK007-027
Ground Lead with 8 mm socket
PK007-001
Sprung Hook
PK007-023
Adapter, 4 mm plug
PK007-022
Adapter, 2 mm plug
PK007-017
Single Lead Adapter
PK007-018
Dual Lead Adapter
PK007-020
Micro Clip, Long
PK007-021
Micro Clip, Short
PK007-019
Pico Hook
PK007-006
Color Coding Rings
(set)
Passive Probe Accessories for PP007 and PP008 Series
DEVICE UNDER
TEST
www.lecroy.com 253
PROBES AND
PROBE ACCESSORIES
PROBES AND PROBE ACCESSORIES
PASSIVE PROBE ACCESSORIES
254 1-800-5-LeCroy
PROBES AND
PROBE ACCESSORIES
ORDERING INFORMATION PP007 AND PP008 PRODUCT CODE
PROBE ACCESSORIES PK701 PK702 PK703 PK704
Sprung Hook 2 1 PK007-001
Standard Ground Lead 2 1 PK007-002
Adjustment Tool 1 1 PK007-003
Rigid Tip 2 2 PK007-004
Spring Tip 2 1 2 PK007-005
Color Coding Rings 2 PK007-006
(3 Red, 3 Yellow, 3 Blue, 3 Green)
Insulating Cap 2 2 PK007-007
IC-cap for 0.5 mm Pitch 1 2 PK007-008
IC-cap for 0.65 mm Pitch 1 2 PK007-009
IC-cap for 0.8 mm Pitch 1 2 PK007-010
IC-cap for 1.0 mm Pitch 1 2 PK007-011
IC-cap for 1.27 mm Pitch 1 2 PK007-012
Ground Blade 1 2 PK007-013
Copper Pad 1 2 PK007-014
PCB-adapter 5 1 PK007-015
Ground Spring 2 1 1 PK007-016
Single Adapter Lead 1 1 PK007-017
Dual Adapter Lead 1 1 1 PK007-018
Pico Hook 2 PK007-019
Microclip Long 0.5 mm 2 1 2 PK007-020
Microclip Short 0.5 mm 2 1 2 PK007-021
Adapter 2 mm Plug PK007-022
Adapter 4 mm Plug PK007-023
Probe Tip Ground Lead 1 1 PK007-024
w/0.8 mm Socket
Probe Tip Ground Lead PK007-025
w/Alligator-clip
Ground Lead with Miniclip 1 PK007-026
Ground Lead with 0.8 mm Socket 1 1 PK007-027
Ground Lead with 2 mm Plug PK007-028
Ground Lead with 4 mm Plug PK007-029
HF-compensated Ground Lead 1 1 PK007-030
BNC-adapter 2 PK007-031
Product Description Brochure 1 1 1 1 PK007-032
ACTIVE VOLTAGE PROBES
www.lecroy.com 255
PROBES AND
PROBE ACCESSORIES
ZS SERIES HIGH IMPEDANCE ACTIVE PROBES
The ZS Series probes provide high impedance and an extensive set of probe tips
and ground accessories to handle a wide range of probing scenarios. The high
1 MΩ input resistance and low 0.9 pF input capacitance mean this probe is ideal
for all frequencies. The ZS Series probes provide full system bandwidth for all
LeCroy oscilloscopes having bandwidths of 1 GHz and lower.
HIGH IMPEDANCE REDUCES CIRCUIT LOADING
ACROSS FULL OSCILLOSCOPE BANDWIDTH
Engineers must commonly probe high frequency signals with high signal fidelity.
Typical passive probes with high input R and C provide good response at lower
frequencies, but inappropriately load the circuit, and distort signals, at higher fre -
quencies. The ZS Series features both high input R (1 MΩ) and low input C (0.9 pF) to
reduce circuit loading across the entire probe/oscilloscope bandwidth. With low
circuit loading, and a form factor that allows probing in confined areas, the ZS Series
becomes the everyday probe for all different types of signals and connection points.
The ZS1000 is ideal for 200–600 MHz oscilloscopes. The ZS1500 is ideal for 1 GHz
oscilloscopes.
PROBES AND PROBE ACCESSORIES
ZS1000
ZS1500
Passive probes are great for low frequency measurements; however, the input capacitance reduces
impedance above 1 kHz. The 1 MΩ input resistance and 0.9 pF capacitance of the ZS probe provide high
impedance across the entire probe bandwidth making it the ideal tool for all your probing needs.
ACTIVE VOLTAGE PROBES
256 1-800-5-LeCroy
PROBES AND
PROBE ACCESSORIES
A VARIETY OF PROBE TIPS FOR VARIED TASKS
Engineers often need to probe a variety of different test points in confined spaces.
The extensive range of standard and optional tip accessories for the ZS Series of
probes ensures that this probe can meet any difficult probing challenge. Various
flexible leads and clips, such as right-angle leads, Y-adapters, and pico hooks, are
also available for probing test points that are spaced farther apart.
INNOVATIVE GROUNDING SOLUTIONS PROVIDE THE
HIGHEST SIGNAL FIDELITY AND EASIEST CONNECTIONS
Making a good ground connection is just as Keeping the ground loop short is critical to
eliminating the effect of high inductance on the signal. The ZS Series of probes provides
several grounding capabilities to offer the highest signal fidelity by shortening the ground
loop and eliminating the effect of that loop on the signal. The standard Offset ground lead
is a “twisted-Z” shape for probing signal and ground points that are extremely close
together. The standard ground blade and copper pad provide the shortest ground loop
possible, and provide a pulse response that cannot be achieved with traditional long
ground leads. A variety of other ground connections are available for nearly any type of
probing requirement.
SPECIFICATIONS ZS1000 ZS1500
ELECTRICAL CHARACTERISTICS
Bandwidth (probe only) 1 GHz 1.5 GHz
Bandwidth (system) 600 MHz at probe tip 1 GHz at probe tip
with 600 MHz with 1 GHz
oscilloscope oscilloscope
Input Capacitance 0.9 pF 0.9 pF
DC Input Resistance 1 MΩ1 MΩ
Probe Offset Range NA ±12 V
Attenuation ÷10 ÷10
Input Dynamic Range ±8 V ±8 V
Non-Destruct Voltage 20 V 20 V
GENERAL CHARACTERISTICS
Cable Length 1.3 m 1.3 m
INCLUDED WITH STANDARD CONFIGURATION
Instruction Manual, English
Color Coding Clips (set of 4 colors)
Certificate of Calibration
1-Year Warranty
Straight Probe Tip (PK-ZS-001) 4 4
Offset Ground (PK-ZS-002) 2 2
Short Lead (PK-ZS-003) 1 1
Long Lead (PK-ZS-004) 1 1
Y Lead Adapter (PK-ZS-005) 1 1
Right Angle Connector (PK-ZS-006) 1 1
Sprung Hook Red (PK-ZS-007R) 1 1
Sprung Hook Black (PK-ZS-007B) 1 1
Ground Blade (PK-ZS-008) 1 1
Copper Pad (PK-ZS-009) 2 2
Color Coding Rings (PK-ZS-010) 4 (sets) 4 (sets)
EXTENSIVE SET OF PROBE TIPS AND GROUND LEADS FOR A WIDE RANGE OF PROBING SCENARIOS
ACTIVE VOLTAGE PROBES
PROBES AND
PROBE ACCESSORIES
PROBES AND PROBE ACCESSORIES
Use the Solder-In Ground with Straight Tip for general purpose
browsing.
The Straight Tip and Offset Ground Lead can be used together for
probing signal and ground points extremely close together.
Hard-to-reach spaces can be be probed with the Bent Sharp Tip
and can be used with a range of ground leads like the flexible
Short Right-angle Lead shown here.
Probe directly on surface mount components, like resistors or
capacitors, with the Discrete SMD Tip. Use this tip with any of the
ground leads, like the flexible Long Right-angle Lead shown here.
Use the Right-angle Connector and the Sprung Hook to probe square
pins spaced far apart from each other.
The Ground Blade and Copper Pad provide the shortest ground loop
for excellent signal fidelity when probing an IC. Use them with the
insulated IC Lead Tip to prevent shorting between test points.
www.lecroy.com 257
ACTIVE VOLTAGE PROBES
258 1-800-5-LeCroy
PROBES AND
PROBE ACCESSORIES
ORDERING INFORMATION PRODUCT CODE
(Set of 4) ZS1500 Active Probes ZS1500-QUADPAK
(Set of 4) ZS1000 Active Probes ZS1000-QUADPAK
1.5 GHz, 1 MΩ, 0.9 pF Active Probe ZS1500
1 GHz, 1 MΩ, 0.9 pF Active Probe ZS1000
REPLACEMENT ACCESSORIES
Replacement Accessory Kit for ZS Series Probes PK-ZS
Straight Probe Tip PK-ZS-001
Offset Ground PK-ZS-002
Short Lead PK-ZS-003
Long Lead PK-ZS-004
Y Lead Adapter PK-ZS-005
Right-Angle Connector PK-ZS-006
Sprung Hook – Red PK-ZS-007R
Sprung Hook – Black PK-ZS-007B
Ground Blade PK-ZS-008
Copper Pad PK-ZS-009
Color Coding Rings PK-ZS-010
AVAILABLE ACCESSORIES
IC Lead Tip PACC-PT003
Discrete SMD Tip PACC-PT004
Bent Sharp Tip PACC-PT005
Solder-In Ground PACC-CD007
Bendable Pogo Ground PACC-CD008
Ground Spring Hook PACC-LD001
Square Pin Ground Spring PACC-LD002
Short Right-angle Lead PACC-LD003
Long Right-angle Lead PACC-LD004
www.lecroy.com 259
PROBES AND
PROBE ACCESSORIES
PROBES AND PROBE ACCESSORIES
Accessories for ZS Series High Impedance Active Probes
PK-ZS-001
Standard Probe Tip
PK-ZS-006
Right Angle Adapter
PK-ZS-009
Copper Pad
PK-ZS-008
Ground Blade
PK-ZS-002
Offset Ground
PK-ZS-010
Marker Bands, 4 colors PK-ZS-005
Y Lead Adapter
PK-ZS-004
Ground Lead, long
PK-ZS-003
Ground Lead, short
PK-ZS-007B
Sprung Hook, black
PK-ZS-007R
Sprung Hook, red
HFP1000
HFP1500
HFP2500
HFP ACTIVE PROBES
LeCroy’s series of HFP active probes are versatile, small and lightweight, yet still
maintain the high bandwidth needed for accurate measurement. Five interchangeable
tips facilitate access regardless of tight fits and difficult locations. The FreeHand
probe holder brings added versatility, allowing several probes to be used at the same
time on a variety of test points while maintaining the short paths needed to preserve
signal fidelity. The HFP probes also offer AutoColor ID, which automatically illuminates
the probe head in a connected oscilloscope’s trace color. This unique capability
eliminates the need to manually apply plastic rings or colored tape to determine
which channel the probe is connected to.
Features:
•1 GHz to 3.5 GHz bandwidth
•0.7 pF input capacitance
•±8 V dynamic range
•±12 V offset range (except HFP1000)
•5 interchangeable tips for probing a variety of test points
•Replaceable probe tip socket
•Hands-free probing with FreeHand probe holder
•AutoColor ID feature matches the channel trace color
SPECIFICATIONS
ELECTRICAL CHARACTERISTICS
BANDWIDTH (PROBE ONLY)
HFP1000 1 GHz
HFP1500 1.5 GHz
HFP2500 2.5 GHz
Input Capacitance 0.7 pF at 1 GHz
DC Input Resistance 100 kΩ
Input Dynamic Range ±8 V
Probe Offset Range N/A (HFP1000)
±12 V (HFP1500, HFP2500)
Attenuation ÷10
Attenuation Accuracy ±1%
Output Zero < 4 mV, referred to input
Offset Accuracy (n/a for HFP1000) ±(1% of offset value +4 mV)
GENERAL CHARACTERISTICS
Cable Length 1.3 m
Probe Head Size (LWH) 61 mm x 7.3 mm x 13.1 mm
Input Sockets Signal and ground sockets
compatible with 0.635 mm (0.025")
square pins, 0.91 mm (0.036")
maximum diameter (for round pins)
INCLUDED WITH STANDARD CONFIGURATION
Instruction Manual, English
Certificate of Calibration
1-year Warranty
ACTIVE VOLTAGE PROBES
260 1-800-5-LeCroy
PROBES AND
PROBE ACCESSORIES
www.lecroy.com 261
PROBES AND
PROBE ACCESSORIES
PROBES AND PROBE ACCESSORIES
ACTIVE VOLTAGE PROBES ACCESS.
ORDERING INFORMATION PRODUCT CODE
1 GHz, 0.7 pF Active Probe (÷10), Small Form Factor HFP1000
1.5 GHz, 0.7 pF Active Probe (÷10), Small Form Factor HFP1500
2.5 GHz, 0.7 pF Active Probe (÷10), Small Form Factor HFP2500
Standard Accessory Kit for HFP2500 PK108
Standard Accessory Kit for HFP1500 PK109
Standard Accessory Kit for HFP1000 PK110
Soft Accessory Case SAC-01
Straight Tip PACC-PT001
Sharp Tip PACC-PT002
IC Lead Tip PACC-PT003
SMD Discrete Tip PACC-PT004
Bent Sharp Tip PACC-PT005
Freehand Probe Holder PACC-MS001
Replaceable Cartridge PACC-MS002
Low C Cartridge PACC-MS003
Solder-In Ground PACC-CD007
Bendable Pogo Ground PACC-CD008
Flexible IC Ground PACC-CD009
Ground Spring Hook PACC-LD001
Square Pin Ground Spring PACC-LD002
Short Right-angle Lead PACC-LD003
Long Right-angle Lead PACC-LD004
Short Single Lead PACC-LD005
Long Single Lead PACC-LD006
0.8 mm Clips PK006-4
Microclip PACC-CL001
HFP1000 Instruction Manual, English HFP1000-OM-E
HFP1500 Instruction Manual, English HFP1500-OM-E
HFP2500 Instruction Manual, English HFP2500-OM-E
INCLUDED WITH STANDARD CONFIGURATION
HFP1000 HFP1500 HFP25000
Straight Tip 4 4 4
Sharp Tip 4 4 4
Bent Tip 4 4
Discrete SMD Tip 4 4
IC Lead Tip 4 4
Square Pin Ground Spring 1 1 1
Flexible IC Ground 1 1 1
Bendable Pogo Ground 1 1 2
Solder-In Ground 1 1 2
Short Single Lead 1 1
Long Single Lead 1
Right-angle Short Single Lead 1 2 1
Right-angle Long Single Lead 1 2 1
Clips (0.8 mm) 2 2 2
FreeHand Probe Holder 1 1
Replaceable Cartridge 1 1 1
Microclips (0.5 mm) 2
Low C Tip Cartridge 1
Soft Accessory Case 1 1
PPO65
PPO66
HIGH-BANDWIDTH TRANSMISSION LINE
The PP066 is a high-bandwidth passive probe designed for use with the WaveMaster and
other high-bandwidth oscilloscopes with 50 Ωinput termination. This very low capacitance
probe provides an excellent solution for higher frequency applications, especially the
probing of transmission lines with 20–100 Ωimpedance. The PP066 accommodates a
wide range of applications, including probing of analog and digital ICs commonly found in
computer, communications, data storage, and other high-speed designs.
Features:
•Interchangeable attenuator tips
•Signal integrity at high bandwidth
•Standard SMA cable connection
•Ultra low capacitance
SPECIFICATIONS
ELECTRICAL CHARACTERISTICS
Bandwidth DC to 7.5 GHz
Risetime < 47 ps
Input C < 0.20 pF
Input R 500 Ω(÷10 cartridge)
1000 Ω(÷20 cartridge)
Maximum Voltage 15 V rms
Cable Length 1 m
The PP065 is a transmission line probe designed for use at very high frequencies.
The probe’s input impedance remains nearly constant over its entire frequency range.
Robust to over voltage and ESD exposure, it is particularly useful in applications
producing fast rising, narrow pulses with amplitudes, which exceed the dynamic
range of active probes.
Features:
•1 GHz
•Low capacitance
•÷100 1 GHz 5 k passive probe
SPECIFICATIONS
Input R Ohm 500 Ω
Maximum Voltage 22 V
Compatibility LCXXX, 93XX, LA314, LA354,
WaveRunner, and WavePro Scopes
Bandwidth 1 GHz
Attenuation 100:1
Input Capacitance 1.5 pF
ORDERING INFORMATION PRODUCT CODE
7.5 GHz Low Capacitance Passive Probe (÷10, 1 kΩ; ÷20, 500 Ω) PP066
1 GHz Low Capacitance Passive Probe (÷10, 5 kΩ) PP065
INCLUDED WITH PP066 PROBE
PACC-AD001 SMA to BNC Adapter
PROBES AND
PROBE ACCESSORIES
262 1-800-5-LeCroy
www.lecroy.com 263
PROBES AND
PROBE ACCESSORIES
PROBES AND PROBE ACCESSORIES
APO33
AP034
DIFFERENTIAL PROBES
High bandwidth, excellent common-mode rejection ratio (CMRR) and low noise make
these active differential probes ideal for applications such as disk drive design and
failure analysis, as well as wireless and data communication design. With the ProBus
interface, the AP034 and AP033 become an integral part of the oscilloscope, allowing
sensitivity, offset and common-mode range to be displayed on the scope screen.
Common mode sensing and input protection capabilities of the AP033 add additional
functionality.
Features for both probes:
•500 MHz (AP033) and 1 GHz (AP034) bandwidths
•x10 gain to ÷ 10 attenuation range (AP033)
•10,000:1 DC CMRR
•Low 9 nV/√Hz noise (AP033)
•1.5 pF/side input C (AP034)
•200 µV/div (AP033)
•Input ESD protection
•Autozero feature
SPECIFICATIONS AP034 AP033
Bandwidth 1 GHz 500 MHz
Gain x1 (÷10 and ÷20 with x10, x1, ÷10 (÷100 with
plug-on attenuators) plug-on ÷10 attenuator)
DC Accuracy 2% typical (probe only) 1% in x1 without
external attenuator
Input Resistance 1 MΩII 1.5 pF each input to ground 1 MΩeach input to ground
2 MΩll 0.85 pF between inputs 2 MΩdifferential between inputs
Differential Mode Range ±400 mV (x1) ±400 mV (x1)
±4 V (÷10) ±40 mV (x10)
±8 V (÷20) ±4 V (÷10)
±40 V (÷100)
Offset Range ±1.6 V (x1) ±400 mV (x1, x10)
±16 V (±10) ±4 V (±10)
±32 V (±20) ±40 V (±100)
Common-Mode Range ±16 V (x1) ±42 V peak (±10)
±42 V (±10) +4.2 V peak (±100)
+42 V (±20)
CMRR 70 Hz 10,000:1 (80 dB) 70 Hz 10,000:1 (80 dB)
1 MHz 100:1 (40 dB) 100 kHz 10,000:1 (80 dB)
100 MHz 18.1 (25 dB) 1 MHz 1000:1 (60 dB)
500 MHz 9:1 (19 dB) 10 MHz 100:1 (40 dB)
250 MHz 5:1 (14 dB)
DIFFERENTIAL PROBES
SPECIFICATIONS (CONTINUED)
AP034/AP033
Max. Nondestruct Voltage ±200 VDC continuous
Cable Length 1.2 m
Operating Temperature 0 °C to 50 °C
Standard Accessories ÷10 Plug-on Attenuator
÷20 Plug-on Attenuator (AP034 only)
Plug-on AC Coupler
Probe Connection Accessory Kit Flex Lead Set (1)
Input ‘Y’ Lead (1)
Mini Clip, 0.8 mm (3)
Mini Clip, 0.5 mm (2)
Ground Lead (1)
Offset Pins, Round (4)
Square Pin Header Strip (1)
Warranty 1 year
PK033 – Standard Probe Accessory Kit for AP033/AP034
Dual Lead AP03X-FLEX-LEAD
Single Lead NA
Offset Pin (package of 10) AP03X-OFFSET-PIN
0.5 mm Clip (red and black) PK006-3
0.8 mm Clip (red and black) PK006-4
1x6 Square Pin Header NA
Other Accessories for AP033/AP034
AC Coupler AP03X-AC-COUPLER
÷10 Attenuator for AP033 AP033-ATTN
÷10 Attenuator for AP034 AP034-DA10
÷20 Attenuator for AP034 AP034-DA20
ORDERING INFORMATION PRODUCT CODE
1 GHz Active Differential Probe (÷1, ÷10, ÷20) AP034
500 MHz Active Differential Probe (x10, ÷1, ÷10 or ÷100) AP033
264 1-800-5-LeCroy
PROBES AND
PROBE ACCESSORIES
www.lecroy.com 265
PROBES AND
PROBE ACCESSORIES
PROBES AND PROBE ACCESSORIES
HIGH VOLTAGE PASSIVE PROBES
The PPE series includes five fixed-attenuation probes covering a range from 2 kV to
20 kV, and one switchable probe providing ÷10/÷100 attenuation for voltage inputs
up to 1.2 kV. All fixed-attenuation, standard probes automatically rescale compatible
LeCroy oscilloscopes for the appropriate attenuation of the probe.
Features:
•Safe, accurate high-voltage measurement
•1.2 kV to 20 kV
HIGH-VOLTAGE PROBES SELECTION GUIDE SPECIFICATIONS
Types Bandwidth Input R Input C Attenuation Maximum Probe Cable
(MHz) (Ω) (pF) Voltage Encoding
PPE1.2kV* 400 50 M < 6 ÷10 / ÷100 600 V/1.2 kV No 2 m
PPE2kV* 400 50 M < 6 ÷100 2 kV Yes 2 m
PPE4kV* 400 50 M < 6 ÷100 4 kV Yes 2 m
PPE5kV* 400 50 M < 6 ÷100 5 kV Yes 2 m
PPE6kV* 400 50 M < 6 ÷1000 6 kV Yes 2 m
PPE20kV†100 50 M < 2 ÷1000 20 kV Yes 3 m
(40 KV peak)
ORDERING INFORMATION PRODUCT CODE
÷10/÷100; 200/300 MHz; 5 MΩ/50 MΩHigh-Voltage Probe PPE1.2KV
600 V/1.2 kV max. Voltage DC
÷1000; 100 MHz; 50 MΩHigh-Voltage Probe PPE20KV
20 kV (40 kV Peak) max. Voltage DC and Peak AC
÷100; 400 MHz; 50 MΩHigh-Voltage Probe PPE2KV
2 kV max. Voltage DC and Peak AC
÷100; 400 MHz; 50 MΩHigh-Voltage Probe PPE4KV
4 kV max. Voltage DC and Peak AC
÷100; 400 MHz; 50 MΩHigh-Voltage Probe PPE5KV
5 kV max. Voltage DC and Peak AC
÷1000; 400 MHz; 50 MΩHigh-Voltage Probe PPE6KV
6 kV max. Voltage DC and Peak AC
Accessory Kit for PPE1.2kV, 2kV, 4kV, 5kV, and 6kV PK103
Standard Probe Accessory Kit for PPE20kV PK104
Ground Lead (15 cm) PK104-1
Hook PK104-2
Standard Probe Accessory Kit for PPE1.2kV, PPE2kV PK103
Sprung Hook (red) PK103-1
Ground Lead (22 cm) PP005-G22
Crocodile Clip PK30x-2
Probe Tip to BNC Adapter PP005-BNC
IC Insulating Tip
Screw Driver
Probe Tip to Banana Plug Adapter
Ground Lead with Banana Plug
Spring Tip (0.8 mm) PP005-ST8
Rigid Tip V2A PP005-RT
STANDARD ACCESSORY KIT FOR PPE20KV
Ground Lead (15 cm) PK104-1
Hook PK104-2
Supplied with probe:
* Probe Kit: Trimming tool, ground lead, rigid tip, IC insulator, BNC adapter, tip insulator, spring hook, red crocodile clip.
4mm safety ground lead, and green/yellow crocodile clip.
†Probe Kit: trimming tool, and ground lead with a crocodile clip.
PPE20KV
PPE6KV
PPE5KV
PPE4KV
PPE2KV
PPE1.2KV
ADP300
ADP305
HIGH VOLTAGE DIFFERENTIAL PROBES
The AP031 is a low cost, battery operated active differential probe intended for measuring
higher voltages. The differential techniques employed permit measurements to be taken
at two points in a circuit without reference to the ground, allowing the oscilloscope to
be safely grounded without the use of opto-isolators or isolating transformers.
Features:
•Safe floating measurements
•15 MHz bandwidth
•700 V maximum input voltage
•Works with any 1 MΩinput oscilloscope
SPECIFICATIONS
Attenuation ÷10 / ÷100
Bandwidth 15 MHz
Input R 4 MΩ
Differential Mode Range ±70 V / ±700 V DC + Peak AC
Common Mode Range ±700 V DC + Peak AC
CMRR 86 dB @ 50 Hz
Power Source (four AA batteries) 56 dB @ 200 kHz
ORDERING INFORMATION PRODUCT CODE
700 V, 15 MHz Differential Probe (÷10, ÷100) AP031
ADP30X high-voltage active probes are safe, easy-to-use, and ideally suited
for measuring power electronics. The ADP300 is designed for troubleshooting
low-frequency power devices and other circuits where the reference potential
is elevated from the ground or the location of the ground is unknown. The
ADP305 is designed for measuring the high-speed floating voltages found in
today’s power electronics.
Features:
•20 MHz and 100 MHz bandwidth
•1,000 V rms common mode voltage
•1,400 V peak differential voltage
•EN 61010 CAT III
•80 dB CMRR at 50/60 Hz
•ProBus system
•Full remote control
PROBES AND
PROBE ACCESSORIES
266 1-800-5-LeCroy
APO31
www.lecroy.com 267
PROBES AND
PROBE ACCESSORIES
PROBES AND PROBE ACCESSORIES
HIGH VOLTAGE DIFFERENTIAL PROBES
SPECIFICATIONS
ELECTRICAL CHARACTERISTICS
Bandwidth 20 MHz (ADP300)
100 MHz (ADP305)
Differential Voltage 1,400 V peak
Common Mode Voltage 1,000 V rms CAT III
Low-Frequency Accuracy (probe only) 1% of Reading
CMRR 50/60 Hz 80 dB (10,000:1)
100 kHz 50 dB (300:1)
Max. Slew Rate (referenced to input) 60,000 V/µs (ADP300)
300,000 V/µs (ADP305)
AC Noise (referenced to input) 50 mV rms
Attenuation ÷100/÷1000 (automatically selected by scope)
Input Impedance Between inputs 8 MΩ, 6 pF
Each input to ground 4 MΩ, 1 pF
Sensitivity 1 V/div to 350 V/div (ADP300)
200 mV/div to 350 V/div (ADP305)
Interface ProBus, 1 MΩ*
GENERAL CHARACTERISTICS
Overall Length 2 m
Input Connectors 4 mm Shrouded Banana Plug
Operating Temperature 0 ˚C to 50 ˚C
Warranty 1 year
STANDARD ACCESSORIES
ADP305
All ADP300 Accessories
Safety Spade (1 Red, 1 Blue)
Plunger Clamp Clip (1 Red, 1 Blue)
Plunger Jaw Clip (1 Red, 1 Blue)
Safe Alligator Clip (1 Red, 1 Blue)
Soft Accessory Case
ADP300
Instruction Manual
Certification of Calibration
Plunger Hook Clip (1 Red, 1 Blue)
Straps for Holding Probe
*Requires AP-1M for oscilloscopes with 50 Ωonly inputs
ORDERING INFORMATION PRODUCT CODE
1,400 V, 100 MHz High-Voltage Differential Probe ADP305
1,400 V, 20 MHz High-Voltage Differential Probe ADP300
CURRENT PROBES
MEASURE CURRENTS IN A WIDE RANGE OF APPLICATIONS
Measuring AC and DC Currents
LeCroy current probes do not require the breaking of a circuit or the insertion
of a shunt to make accurate and reliable current measurements. Based on a
combination of Hall effect and transformer technology, LeCroy current probes
are ideal for making accurate AC, DC, and impulse current measurements.
Fully Integrated with Oscilloscope
Many current probes require external power supplies or amplifiers to display a
waveform on the oscilloscope screen. All LeCroy current probes are powered
through the LeCroy ProBus connection and require no additional hardware.
Along with providing power, the ProBus connection allows the current probe and
oscilloscope to communicate, resulting in current waveforms automatically displayed
on screen in Amps, and calculated power traces scaled correctly in Watts. This full
integration also allows for Degauss and Autozero functions to be done directly from
the oscilloscope with a single button press.
Applications
LeCroy current probes are available in a wide range of models for a wide range
of applications. The full range of LeCroy current probes includes models with
bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 10 mA/div.
Multiple current probes can be used together to make measurements on three-phase
systems, or a single current probe can be used with a voltage probe to make accurate
instan taneous power measurements. LeCroy current probes are often used in applications
such as the design and test of switching power supplies, motor drives, electric vehicles,
and uninterruptible power supplies.
268 1-800-5-LeCroy
PROBES AND
PROBE ACCESSORIES
Accurately measure AC, DC, and impulse currents.
PROBES AND
PROBE ACCESSORIES
PROBES AND PROBE ACCESSORIES
CURRENT PROBES
CP031 – 30A, 100 MHz
The CP031 is LeCroy’s highest bandwidth current probe. Along with the high
100 MHz bandwidth the CP031can probe continuous currents of 30 Arms and
peak currents up to 50 A. The CP031 features a small form factor making it
easier to probe on a crowded, compact board.
Features:
•100 MHz bandwidth
•Small form factor accommodates large conductors with small jaw size
•30 Arms continuous current, 50 Apeak current
CP030 – 30 A, 50 MHz
The CP030 was designed with a small form factor for today’s crowded boards.
The small jaw can probe currents in tight spaces and still clamp onto conductors
up to 5 mm in diameter. Continuous currents of 30 A rms and peak currents of
50 A can be measured by the CP030, which also features a 50 MHz bandwidth.
Features:
•Small form factor accommodates large conductors with small jaw size
•30 Arms continuous current, 50 MHz bandwidth
•50 Apeak current
AP015 – 30 A, 50 MHz
The AP015 current probe can measure continuous current of 30 A rms and peak
pulses of up to 50 A for durations up to 10 seconds. This probe also features
an overheating protection circuit, which will display an on-screen warning to
the user to prevent damage. A probe unlock detection feature is also built in
to the AP015 to ensure accurate measurements.
Features:
•30 Arms continuous current, 50 MHz bandwidth
•50 Apeak current for up to 10 seconds
•Overheating and Probe Unlock Detection
CP150 – 150 A, 10 MHz
Features:
•150 Arms continuous current
•500 Apeak
•10 MHz bandwidth
CP500 – 500 A, 2 MHz
Features:
•500 Arms continuous current
•700 Apeak
•2 MHz bandwidth
CP030
CP031
AP015
CP500
CP150
www.lecroy.com 269
SPECIFICATIONS CP031*† CP030*†
ELECTRICAL CHARACTERISTICS
Max. Continuous Input Current 30 A 30 A
Bandwidth 100 MHz 50 MHz
Max. Peak Current at Pulse Width 50 A ≤ 10 µs 50 A ≤ 10 µs
Rise Time (typical) ≤ 3.5 ns ≤ 7 ns
Minimum Sensitivity 20 mA/div 20 mA/div
Max. In-Phase Current – –
Low-Frequency Accuracy 1% 1%
AC Noise ≤ 2.5 mA ≤ 2.5 mA
Coupling AC, DC, GND AC, DC, GND
GENERAL CHARACTERISTICS
Cable Length 1.5 m 1.5 m
Weight 240 g 240 g
Max. Conductor Size (diameter) 5 mm 5 mm
Interface ProBus, 1 MΩonly‡ProBus, 1 MΩonly‡
Usage Environment Indoor Indoor
Operating Temperature 0 ˚C to 40 ˚C 0 ˚C to 40 ˚C
Max. Relative Humidity 80% 80%
Max. Altitude 2000 m 2000 m
Maximum Insulated Wire Voltage 300 V CAT I, 150 V CAT II 300 V CAT I
CURRENT PROBES
270 1-800-5-LeCroy
PROBES AND
PROBE ACCESSORIES
0.001
0.01
0.1
1
10
Frequency (Hz
)
Insertion
Impedance
(Ω)
0
5
10
15
20
25
30
35
Frequency (Hz)
Current
(Arms)
Frequency (Hz)
0.001
0.01
0.1
1
10
Insertion
Impedance
(Ω)
0
5
10
15
20
25
30
35
Frequency (Hz)
Current
(Arms)
CP031 – 30 A, 100 MHz
CP031 – 30 A, 100 MHz
CP030 – 30 A, 50 MHz
CP030 – 30 A, 50 MHz
ORDERING INFORMATION PRODUCT CODE
30 A; 100 MHz Current Probe – CP031
AC/DC; 30 Arms; 50 Apeak Pulse
30 A; 50 MHz Current Probe – CP030
AC/DC; 30 Arms; 50 Apeak Pulse
30 A; 50 MHz Current Probe – AP015
AC/DC; 30 Arms; 50 Apeak Pulse
150 A; 10 MHz Current Probe – CP150
AC/DC; 150 Arms; 500 Apeak Pulse
500 A; 2 MHz Current Probe – CP500
AC/DC; 500 Arms; 700 Apeak Pulse
* Guaranteed at 23 °C ±3 °C †The CP031 and CP030 are compatible with LeCroy X-Stream oscilloscopes running firmware version 4.3.1.1 or greater.
‡Requires AP-1M for use with 50 Ωinput only oscilloscopes.
Maximum Input Current vs. Frequency
Insertion Impedance vs. Frequency
(typical)
Maximum Input Current vs. Frequency
Insertion Impedance vs. Frequency
(typical)
AP015 CP150 CP500
30 A 150 A 500 A
50 MHz 10 MHz 2 MHz
50 A ≤ 10 s 500 A ≤ 30 µs 700 A
≤ 7 ns < 35 ns < 175 ns
10 mA/div 200 mA/div 200 mA/div
– 500 A 1150 A
1% 1% 1%
≤ 25 mA 25 mA
AC, DC, GND AC, DC, GND AC, DC, GND
2 m 2 m 6 m
300 g 500 g 630 g
5 mm 20 mm 20 mm
ProBus, 1 MΩonly‡ProBus, 1 MΩonly‡ProBus, 1 MΩonly‡
Indoor Indoor Indoor
0 ˚C to 40 ˚C 0 ˚C to 40 ˚C 0 ˚C to 40 ˚C
80% 80% 80%
2000 m 2000 m 2000 m
300 V CAT I 600 V CAT II, 300 V CAT III 600 V CAT II, 300 V CAT III
CURRENT PROBES
www.lecroy.com 271
PROBES AND
PROBE ACCESSORIES
PROBES AND PROBE ACCESSORIES
0.001
0.01
0.1
1
10
Frequency (Hz)
Insertion
Impedance
()
AP015 – 30 A, 50 MHz
0
50
100
150
200
250
300
350
400
450
500
550
Frequency (Hz)
Current
(A rms)
10 100 1 k 10 k 100 k 1 M 10 M
20
0
40
60
80
100
120
140
160
Frequency (Hz)
Current
(A rms)
CP150 – 150 A, 10 MHz CP500 – 500 A, 2 MHz
0.001
0.010
0.100
Frequency (Hz)
Insertion
Impedance
0.001
0.01
0.1
1
Frequency (Hz)
Insertion
Impedance
CP150 – 150 A, 10 MHz CP500 – 500 A, 2 MHz
* Guaranteed at 23 °C ±3 °C †The CP031 and CP030 are compatible with LeCroy X-Stream oscilloscopes running firmware version 4.3.1.1 or greater.
‡Requires AP-1M for use with 50 Ωinput only oscilloscopes.
Insertion Impedance vs. Frequency
(typical)
Maximum Input Current vs. Frequency
Insertion Impedance vs. Frequency
(typical)
Maximum Input Current vs. Frequency
Insertion Impedance vs. Frequency
(typical)
TF-DSQ
PROBE DESKEW AND CALIBRATION
272 1-800-5-LeCroy
PROBES AND
PROBE ACCESSORIES
The TF-DSQ fixture facilitates calibration of timing measurements in single-ended and
differential probes—a unique concern in high-speed measurements. By requiring only
one connection of a probe to the fixture and one button press, the TF-DSQ ensures
probe calibration results that are valid for the duration that the probe is connected to
the circuit. An extremely fast edge with 75 ps risetime combines with probe gain and
offset calibration capabilities for added accuracy.
Features:
•Deskews to ±20 ps typical accuracy
•Differential and single-ended drive
•75 ps edge for precise deskewing
•Calibrates gain, offset and skew at the same probing point
•Accounts for risetime variations
•Accounts for common-mode voltage variations
•DC gain calibration accounts for probe loading effects
•Integrated operation with scope for fully automatic calibration
SPECIFICATIONS
SCOPE COMPATIBILITY SCOPES
(requires software version 3.6.0 or later) WaveMaster (WM8420A and WM8620A
including all WaveMaster XXL models)
Serial Data Analyzers (SDA 18000,
SDA 11000, SDA 9000, SDA 4020, and
SDA 6020 including all SDA XXL models)
Disk Drive Analyzers (DDA 5005A and
5005A XXL)
Scope Connection ProLink
Probes Supported WL600 and WL300 with all Probing
Accessories PP
AP033, AP034, PP066
HFP1000, HFP1500, HFP2500,
ZS1500, ZS1000, D11000PS, DA18000
DC Range ±5 V Single-ended, ±10 V Differential
DC Accuracy ±(1% + 600 µV)
Edge Risetime 75 ps (typical) < 95 ps (guaranteed)
Edge Amplitude and Rep Rate Approximately 800 mV @ 10 MHz
Deskew Accuracy ±20 ps (typical)
ORDERING INFORMATION PRODUCT CODE
Probe Deskew and Calibration Fixture TF-DSQ
Included: ProLink Extender 48" 50 ohm Cable with
Male SMA Connectors Calibration Certificate
Operator’s Manual Soft Accessory Case
SAC-01
ADPPS
EZ PROBE
EZ PROBE POSITIONER
www.lecroy.com 273
PROBES AND
PROBE ACCESSORIES
The EZ-Probe Positioner provides stable, accurate X, Y and Z positioning in one fluid
motion. Its unique 3-D joystick, with 3:1 motion reduction and single-clutch, fully-
articulating arm, allow simple, precise positioning in anything from card cages to
MCMs. Any current handheld probes can be easily attached, facilitating the
measurement process and ensuring more precise connectivity.
ORDERING INFORMATION PRODUCT CODE
Cascade Microtech EZ-Probe Positioner EZ PROBE
PROBES AND PROBE ACCESSORIES
ADPPS
Power Adapter for AP033, AP034 and HFP1000 Active Probes; allows the probe’s
output to be connected to other non-ProBus test equipment, including spectrum
and network analyzers.
ORDERING INFORMATION PRODUCT CODE
ProBus-to-BNC and Power Adapter ADPPS
for AP033, AP034, and HFP Series
(BW limited to 1 GHz)
TRANSIT CASE
Soft Accessory Case for probes—features inside flap for storing manuals, plus roomy
interior for a probe and its many accessories.
ORDERING INFORMATION PRODUCT CODE
Soft Accessory Case for Probes SAC-01
