P R O B E S A N D P R O B E A C C E S S O R I E S D11000PS DIFFERENTIAL PROBE SYSTEM The D11000PS extends the full signal acquisition performance of the SDA 11000 and SDA 9000 to the probe tips. With 11 GHz system bandwidth, the probe enables direct measurement of high-speed serial data streams up to 6.25 Gb/s. The D11000PS also provides 11 GHz system bandwidth when used with the SDA 18000. Choice of Interconnect Styles Without Compromising Performance The D11000PS provides both direct Solder-In and cabled SMA interconnect lead assemblies. Each interconnect lead comes with a dedicated probe amplifier module that has calibration data optimized for the respective lead. This eliminates the performance compromise of using a single calibration for multiple lead types. The Solder-In lead provides the highest possible signal integrity with a high loading impedance. The dual SMA interconnect leads provide a true differential 50 input. This is a convenient alternative to direct cabling into the oscilloscope inputs, freeing up the second channel for other signal input, and eliminating the need to set up waveform math and match cable delays. Each individual probe is characterized with this system. Information on the probe's frequency and time domain responses are stored in non-volatile memory within the probe amplifier module. This information is uploaded to the higher bandwidth SDA's when the probe is connected. The probe calibration data and the SDA oscilloscope's calibration data combine to generate new equalization filters for the composite system. The resulting compensation system corrects for frequency response deviations, as well as group delay correction and reflection cancellation. www.lecroy.com 237 PROBES AND PROBE ACCESSORIES Unsurpassed Waveform Accuracy When used to acquire input signals for the SDA 11000, SDA 9000, or SDA 18000, the D11000PS provides unprecedented waveform fidelity, even with signals at higher serial data rates. The D11000PS utilizes third generation compensation calibration, the most advanced in use today, to provide optimal system response. P R O B E S A N D P R O B E A C C E S S O R I E S D11000PS DIFFERENTIAL PROBE SYSTEM Reproducing accurate serial data eye patterns requires maintaining precise magnitude and phase relationships between the fundamental and the odd harmonics. The advanced calibration system used in the D11000PS assures the best eye pattern fidelity. Superior Probe Loading Characteristics Accurate frequency response is not enough to assure good waveform fidelity. Excessive probe loading can cause waveform distortion. The D11000PS continues the legacy of LeCroy high-performance probe design, placing special emphasis on minimizing loading of the circuit under test. The Solder-In lead and dedicated probe amplifier module have a high input resistance at DC and low frequencies, allowing the probe to be used in circuits which cannot drive the low resistance of a pure transmission line probe. The direct cabled SMA inputs have 50 input impedance with low VSWR. Ease of Use Attention to fine details during the D11000PS design process has resulted in several "ease of use" features. A common mode measure feature allows the user to measure the average common mode component with a single click in the probe control menu. AutoColor ID lights an indicator in the probe body, matching the color of the waveform trace. When multiple channels are used, this feature instantly identifies which waveform corresponds to which probe. Several connection accessories designed specifically for the D11000PS provide convenient and secure mounting of the probe body and Solder-In tip to the test circuit. DC blocking adapters extend the common mode range of the SMA cabled input for use with higher common mode voltages such as Digital Video Interface (DVI). A finger wrench allows tightening of SMA connectors on dense test fixtures. 238 1-800-5-LeCroy P R O B E S A N D P R O B E A C C E S S O R I E S D11000PS DIFFERENTIAL PROBE SYSTEM Compatibility The D11000PS is designed specifically for use with the SDA 11000, SDA 9000, or SDA 18000. However, it does contain additional calibration data for use with all of the lower bandwidth WaveMaster, SDA, and DDA 5005A Series oscilloscopes and analyzers. SPECIFICATIONS Bandwidth, System, -3 dB Rise Time, System Rise Time, Probe only Attenuation, Nominal LF Attenuation Accuracy Output Zero Noise, System Differential Mode Range Common Mode Range Input Resistance at DC, (Solder-In lead) Minimum Input Impedance, (Solder-In lead, to 11 GHz) Input Impedance, (SMA cable input) Input VSWR, (Typical, each lead to ground) CMRR, (Typical) 11 GHz (Typical)* < 50 ps (Typical)* < 40 ps /3 2% (20-30 C) < 15 mV referred to input 5 mV rms (Typical)1 1 V 4 V, Solder-In tip 2 V, SMA cable input 40 k differential 20 k each side to ground > 175 (Refer to graph) 50 < 1.5:1 DC-6 GHz < 2.0:1 6 GHz-11 GHz > 40 dB DC-1 GHz > 30 dB 1 GHz-4 GHz > 20 dB 4 GHz-11 GHz * Measured as a system with SDA 11000, SDA 9000 and SDA 18000. Can be extended by using DC Blocking Adapters. 239 PROBES AND PROBE ACCESSORIES www.lecroy.com P R O B E S A N D P R O B E A C C E S S O R I E S D11000PS DIFFERENTIAL PROBE SYSTEM D11000PS Includes: Probe amplifier modules (2-1 each for SMA input and Solder-In lead), Solder-In lead assembly (2), SMA interconnect lead, SMA input cables (matched pair), Probe body, SMA DC blocking adapters (2), ground lead and clip, SMA finger wrench (2), tip retaining clip kit for Solder-In lead, probe body mounting clamp set, FreeHand probe stand, ESD dissipating wrist strap, SAC-01 soft accessory case with insert, small accessory case, D11000PS Instruction Manual, certificate of traceable calibration. ORDERING INFORMATION Differential Probe System Replacement Solder-In Tip Assembly NIST Traceable Calibration with Test Data (one module) 240 1-800-5-LeCroy PRODUCT CODE D11000PS D11000SI D11000PS-CCNIST P R O B E S A N D P R O B E A C C E S S O R I E S WAVELINK DIFFERENTIAL PROBES WaveLink high bandwidth differential probes are designed to provide an optimum mechanical connection for signal measurement. They virtually eliminate distortion when measuring signals, which is particularly useful in eye pattern measurements-- now routine for systems using fast serial data bus architecture. WaveLink probes provide industry-leading technology for wideband signal connection to test instruments. The first differential probes to employ SiGe technology, they deliver full system bandwidth when used with LeCroy 6 GHz, 5 GHz, and 3 GHz instruments. They are also the first differential probes to use a unique calibration process to achieve superb waveform fidelity for routine voltage measurements. Features: * Unique adjustable tips for reliable contact * Wide assortment of small tips ideal for restricted spaces * Best-in-class probe loading for accurate signal measurement * Superior loading characteristics and precise frequency response * Outstanding fidelity for high-speed signals D600A-AT and D300A-AT Features: * Built-in thumbwheel for precise positioning of tip; stays put after adjustment * Maintains sharp points for good contact * Tips made of "NiTiNOL," a super-elastic nickel-titanium alloy * Probe flexes as you apply pressure and consistently returns to original form D600A-AT D300A-AT D600ST D350ST D500PT D600ST and D350ST Features: * Best-in-class mechanical design for optimum utility * Small tip high bandwidth differential probe * Three interconnect configurations for flexibility * Very small form factor for accessing tight spaces * Highly flexible long lead * Inexpensive and easily replaceable D500PT Positioner Mounted Tip Features: * Positioned tip assembly * Very small tip geometry for accessing physically constrained locations * Ideal for applications requiring multiple probes on adjacent pads * Telescoping tips for reliable tip contact--even when probe it tilted * Mounts in probe positioner or can be hand held * EZ-Probe positioner available as an accessory Each of the interchangeable leads is a thin, highly flexible 145 mm (5.7") long lead connecting the tip and the D600ST/D350ST probe tip module. www.lecroy.com 241 PROBES AND PROBE ACCESSORIES WaveLink D600ST and D350ST Best-in-class mechanical design for optimum utility: * Small tip, high bandwidth differential probe * Three interconnect configurations for flexibility * Very small form factor for accessing tight spaces P R O B E S A N D P R O B E A C C E S S O R I E S WAVELINK DIFFERENTIAL PROBES FLEXIBLE INTERCONNECTION OPTIONS --WITHOUT SACRIFICING PERFORMANCE D500PT Positioner Mounted Probe Tip Module The probe has a very thin form factor, allowing multiple probes to be used when several channels are required to monitor signals from the same small IC. It has 2 mm of Z-axis compliance through spring-loaded telescoping tips, allowing considerable angular freedom relative to the circuit board while still maintaining reliable contact with both inputs. A ball joint between the tip and mounting arm makes it even easier to adjust for placement when already mounted in a positioner. A small thumbscrew allows precise and secure adjustment of the tip spacing. D600A-AT and D300A-AT Adjustable Tips WaveLink adjustable tip probes are designed to provide an optimum mechanical connection for signal measurement. * Built-in thumbwheel for precise positioning of tip--stays put after adjustment * Maintains sharp points for good contact * Tips made of "NiTiNOL," a superelastic nickel-titanium alloy * Flexes as you apply pressure * Consistently returns to original form EZ-Probe Positioner The EZ-Probe positioner provides stable, accurate positioning in the x-y-z axis. Ideal for use with the D500PT and D600A-AT/D300A-AT probe tips. The unique, 3:1 motion reduction joystick allows simple, precise positioning of the attached probe in both the horizontal and vertical measuring plane. The probe has a fully articulating arm, providing 30 cm (12") reach in virtually any direction. 242 1-800-5-LeCroy The Probe Tip Modules contain the active amplifier circuitry. Different modules have different electrical and physical interconnect characteristics, allowing the user to select the module appropriate for the application. P R O B E S A N D P R O B E A C C E S S O R I E S WAVELINK DIFFERENTIAL PROBES THREE DIFFERENT TIPS FOR INTERCONNECT FLEXIBILITY Solder-In Lead The Solder-In interconnect lead features the smallest physical tip size of any high bandwidth differential probe and the highest level of electrical performance. Two very small damping resistors are directly soldered into the connect points providing a reliable, intermittent free electrical connection. The resistors have highly flexible leads allowing connection to input points with a wide range of input spacing. Quick Connect (D600ST only) The Quick Connect interconnect lead enables you to quickly move the probe between multiple test points on the test circuit. Just solder a pair of damping resistors at each location where interconnection is required. A small connector mounted on the probe tip, plugs into the damping resistors, letting you quickly move between sets of test points. www.lecroy.com 243 PROBES AND PROBE ACCESSORIES Square Pin Many applications, such as IC characterization boards, use standard 0.025" square pins for interconnect. The Square Pin interconnect lead directly mates with a pair of 0.025" (0.635 mm) square pins which are mounted on standard 0.100" (2.54 mm) centers. P R O B E S A N D P R O B E A C C E S S O R I E S WAVELINK DIFFERENTIAL PROBES SPECIFICATIONS Rise Time, probe only D600A-AT D600ST-SI D500PT D300A-AT D350ST-SP LF Attenuation Accuracy (with 0 V common mode) < 70 ps* < 65 ps* < 100 ps < 95 ps < 90 ps D600A-AT, D300A-AT, D600ST, and D500PT 2% 0 1.2 V 5% 1.2 V 2.4 V D350ST 2% 0 2.5 V 5% 2.5 V 5 V Output Zero (within 15 minutes after Autozero) D600A-AT, D300A-AT, D600ST, and D500PT < 10 mV RTI D350ST Bandwidth, System DC to -3 dB (Typical) < 20 mV RTI D600ST-SI D600ST-QC D600ST-SP D600A-AT D300A-AT D350ST-SP D350ST-SI D500PT Input Dynamic Range 6 GHz** 4 GHz** 3 GHz** 6 GHz** 3 GHz 3 GHz 3 GHz 5 GHz D600A-AT, D300A-AT, D600ST, and D500PT 2.4 V D350ST Common Mode Range (Max. peak voltage either input to ground) 5 V D600A-AT, D300A-AT, D600ST, and D500PT 2.4 V D350ST DC Input Resistance 5 V D600A-AT, D300A-AT, D600ST, and D500PT 4 k differential 2 k either input to ground D350ST 8 k differential 4 k either input to ground *Measured with 6 GHz or greater oscilloscope Measured with 5 GHz oscilloscope Measured with 3 or 4 GHz oscilloscope **Typical, with 6 GHz or greater oscilloscope Typical, with 3 or 4 GHz oscilloscope 244 1-800-5-LeCroy P R O B E S A N D P R O B E A C C E S S O R I E S WAVELINK DIFFERENTIAL PROBES SPECIFICATIONS (CONTINUED) CMRR D600A-AT DC to 1 GHz 1 GHz to 3 GHz 3 GHz to 7 GHz D600ST DC to 1 GHz 1 GHz to 3 GHz 3 GHz to 7 GHz D500PT DC to 1 GHz 1 GHz to 3 GHz 3 GHz to 5 GHz D350ST DC to 1 GHz 1 GHz to 3 GHz D300A-AT DC to 1 GHz 1 GHz to 3 GHz Noise > 40 dB > 30 dB > 20 dB > 30 dB > 25 dB > 20 dB > 25 dB > 19 dB > 16 dB > 30 dB > 25 dB > 40 dB > 30 dB D600A-AT, D600ST, D500PT 5.8 mVrms with 6 GHz oscilloscope D300A-AT D350ST 5.0 mVrms with 3 GHz oscilloscope 9.5 mVrms with 3 GHz oscilloscope ORDERING INFORMATION PROBE TIP MODULES WaveLink 7.5 GHz, Differential Probe Adjustable Tip Module WaveLink 4 GHz, Differential Probe Adjustable Tip Module WaveLink 7 GHz, Differential Probe Small Tip Module WaveLink 4 GHz, 5 V Differential Probe Small Tip Module WaveLink 6 GHz, Differential Positioner Mounted Tip Module POSITIONER Cascade Microtech EZ-Probe Positioner SERVICE OPTIONS NIST Traceable Calibration with Test Data (one module) D600A-AT* D300A-AT* D600ST* D350ST* D500PT* WL600 WL300 EZ PROBE D600A-AT-CCNIST D300A-AT-CCNIST D600ST-CCNIST D350ST-CCNIST D500PT-CCNIST * For a complete probe, order a WL300 or WL600 Probe Body with Probe Tip Module. -CCNIST NIST traceable calibration with test data is an available option for D600ST, D350ST, D500PT, D600A-AT, or D300A-AT probe tip module only when ordered with either a WL600 or WL300 probe body. www.lecroy.com 245 PROBES AND PROBE ACCESSORIES PROBE BODIES WaveLink ProLink Probe Body WaveLink ProBus Probe Body PRODUCT CODE P R O B E S A N D P R O B E A C C E S S O R I E S WAVELINK DIFFERENTIAL PROBES ORDERING INFORMATION (CONTINUED) CONSUMABLES AND REPLACEMENT PARTS Replacement Quick Connect Lead Set for D600ST Replacement Solder-In Lead Set for D600ST Replacement Square Pin Lead Set for D600ST Extra Solder-In Lead for D350ST Extra Square Pin Lead for D350ST Replacement Tip Assembly for D500PT Replacement Resistor Kit for D600ST-SI (10) Replacement Resistor Kit for D600ST-QC (20) Replacement Probe Tip Holder Kit Replacement Probe Body Mounting Kit Replacement Probe Tips for D500PT (pkg. of 4) Replacement Resistor Kit for D350ST-SI (10) Probe Characterization Fixture WaveLink Probe Series Instruction Manual PRODUCT CODE D600ST-QC D600ST-SI D600ST-SP D350ST-SI D350ST-SP D500PT-TIP PK600ST-1 PK600ST-2 PK600ST-3 PK600ST-4 PK500PT-1 PK350ST-1 PCF-200 WL-OM-E D600A-AT, D300A-AT Adjustable Tip Modules Include: Protective storage case, ground wire and clip, WaveLink Series instruction manual, Quick Start guide, calibration certificate. D600ST Small Tip Module Includes: Solder-In interconnect lead set with replacement damping resistors (10), Quick Connect interconnect lead set with additional damping resistors (20), Square Pin interconnect lead set, ground wire and clip, probe tip mounting kit, WaveLink Series instruction manual, Quick Start guide, calibration certificate. D350ST Small Tip Module Includes: Solder-In interconnect lead set with replacement damping resistors (10), Square Pin interconnect lead set, ground wire and clip, probe tip mounting kit, WaveLink Series instruction manual, Quick Start guide, calibration certificate. D500PT Positioner Mounted Tip Includes: Positioned tip assembly, Probe tip module, Module mounting clamp, Ground lead and clip, WaveLink Series instruction manual, Quick Start guide, Calibration certificate, FreeHand probe stand, Tip repair tool, Replacement tips (2) WL600, WL300 Probe Bodies Include: SAC-01 Soft accessory case with WaveLink Series insert, probe characterization fixture, probe body mounting clip, probe cable clamp (2), and small probe accessory case. WaveLink Probe Calibration When ordered with WL600 or WL300 also substitute: Certificate of NIST traceable calibration in place of calibration certificate. 246 1-800-5-LeCroy P R O B E S A N D P R O B E A C C E S S O R I E S PASSIVE PROBES Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 M. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400 V, some as high as 600 V. LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input. Each passive probe is recommended for a certain oscilloscope, using the right passive probe with the right oscilloscope means that the probe can be properly compensated across the entire bandwidth. Using probes with a different oscilloscope will only let you compensate for low frequencies. Features: * Bandwidth from 200 MHz to 500 MHz * Probe encoding ring for automatic scale factor readout on LeCroy oscilloscopes Model PP005A PP006A PP007-WS PP007-WR PP008 PP009 PP010 PP011 Bandwidth Input R Input C Attenuation Maximum Voltage Diameter Recommended Oscilloscope 500 MHz 500 MHz 500 MHz 500 MHz 500 MHz 500 MHz 200 MHz 500 MHz 10 M 10 M 10 M 10 M 10 M 10 M 10 M 10 M 11 pF 12 pF 9.5 pF 9.5 pF 9.5 pF 9.5 pF 12.5 pF 9.5 pF 10:1 10:1 10:1 10:1 10:1 10:1 10:1 10:1 500 V 600 V 400 V 400 V 400 V 400 V 600 V 400 V 5 mm 5 mm 2.5 mm 2.5 mm 2.5 mm 5 mm 5 mm 5 mm 1, 2, 12, 13 3, 11 4 5, 7, 9 4, 6, 8 4, 6, 8 10 5, 7, 9 Recommended Oscilloscope 1 9300 Series 2 LC Series 3 LT Series 4 WaveSurfer 400 Series 5 WaveRunner 6000 Series 6 WaveRunner Xi Series ( 600 MHz) 7 WaveRunner Xi (1 GHz-2 GHz) ORDERING INFORMATION /10, 500 MHz 10 M Passive Probe /10, 500 MHz 10 M Passive Probe /10, 500 MHz 10 M Passive Probe /10, 500 MHz 10 M Passive Probe /10, 500 MHz 10 M Passive Probe /10, 500 MHz 10 M Passive Probe /10, 200 MHz 10 M Passive Probe /10, 500 MHz 10 M Passive Probe 248 1-800-5-LeCroy 8 9 10 11 12 13 WaveSurfer Xs Series ( 600 MHz) WaveSurfer Xs Series (1 GHz) WaveJet Series ( 200 MHz) WaveJet Series ( 350 MHz) WavePro 900 Series WavePro 7000 Series PRODUCT CODE PP005A PP006A PP007-WS-1 PP007-WR-1 PP008 PP009 PP010 PP011 P R O B E S A N D P R O B E A C C E S S O R I E S WAVELINK DIFFERENTIAL PROBES WAVELINK PROBE COMPATIBILITY CHART D600A-AT D300A-AT D600ST D350ST D500 PT WL600 WL300 SDA 18000* SDA 11000* SDA 9000* SDA 6020 SDA 4020 * * NC FP RP RP1 WM8620A WM8420A * DDA 5005A * * * * * * * * * * * * * RP1 RP1 RP1 Recommended Not Compatible Operates at Full Performance Operates with Reduced Performance with LPA adapters. Frequency response > 3 GHz may be altered Operates with Reduced Performance with LPA adapters. Frequency response > 3 GHz may be altered DDA 3000 WP7300A WP7200A WP7100A WR 204Xi WR 104Xi WR 64Xi WR 62Xi WR 44Xi WR 6KA * * * * * NC * * * NC * * * NC * WL300 RP FP RP FP RP WL600 FP FP FP FP FP *Operates on channels in 6 GHz mode only 247 PROBES AND PROBE ACCESSORIES www.lecroy.com P R O B E S A N D P R O B E A C C E S S O R I E S PASSIVE PROBES ACCESSORIES ORDERING INFORMATION PK001 - Standard Probe Accessory for PP002 Ground Lead PP002 Probe Tip to BNC adapter Sprung Hook PP002 M/F Lead - Long (4") M/F Lead - Short (2") PK102 - Standard Probe Accessory Kit for PP005/PP005 Sprung Hook (Black) Spring Tip (0.38 mm) Spring Tip (0.8 mm) Rigid Tip (0.8 mm) Probe Tip to BNC Adapter Ground Lead (11 cm) Ground Lead (22 cm) Ground Lead (Spring) IC Insulating Tip Probe Tip to BNC Adapter Adjustment Screw Driver PPK106 - SMT Accessories for PP005/PP005A, PPExkV Dual Lead Adapter Single Lead Adapter 0.5 mm Clip (Orange) Probe Tip to PCB Adapter M/F Lead - Long (4") M/F Lead - Short (2") 0.5 mm Clip (Yellow) PK101 - Microclip Accessory Kit for PP005/PP005A Single Lead Adapter QFPIC Clip (0.5 mm Pitch) PK006 - SMT Accessories for PP006/PP006A Dual Lead Adapter PK006 Single Lead Adapter PK006 0.5 mm Clip (Black and Red) 0.8 mm Clip (Black and Red) M/F Lead - Long (4") M/F Lead - Short (2") PP001/002-1 PP001/002-2 PP001/002-3 PP005-HOOK PP005-ST38 PP005-ST8 PP005-RT PP005-BNC PP005-GL11 PP005-GL22 PP005-GLPT PK106-1 PK106-2 PK106-3 PK106-4 PK106-5 PK106-6 PK106-8 PK106-2 PACC-CL001 PK116-1 PK116-2 PK116-3 PK006-1 PK006-2 PK006-3 PK006-4 www.lecroy.com 249 PROBES AND PROBE ACCESSORIES PK116 - Standard Probe Accessory Kit for PP006/PP006A Sprung Hook Ground Lead Ground Pin Insulating Tip Screw Driver PRODUCT CODE P R O B E S A N D P R O B E A C C E S S O R I E S PASSIVE PROBES ACCESSORIES ORDERING INFORMATION PKIT1-5MM-102 - Basic Adapter Kit for PP009 Sprung Hook Standard Ground Lead Adjustment Tool Rigid Tip, 0.8 mm IC Cap, 2.54 mm pitch Spring Tip 0.8 mm (Qty. 6) BNC Adapter Adapter, 4 mm plug Ground Spring High Frequency Compensated Ground Lead Spring Tip 0.38 mm (Qty. 5) PKIT1-5MM-101 - Micro Clip Kit for PP009 Single Lead Adapter Microclip Long, Green Microclip Long, Yellow Microclip Short, Green Microclip Short, Yellow PKIT2-5MM-101 - Standard Accessory Kit for PP010 Sprung Hook Standard Ground Lead Adjustment Tool Ground Attachment IC Test Tip Color Coding Rings (set) 250 1-800-5-LeCroy PRODUCT CODE PK1-5MM-101 PK1-5MM-102 PK1-5MM-103 PK1-5MM-104 PK1-5MM-108 PK1-5MM-109 PK1-5MM-110 PK1-5MM-117 PK1-5MM-118 PK1-5MM-123 PK1-5MM-124 PK1-5MM-111 PK1-5MM-114G PK1-5MM-114Y PK1-5MM-115G PK1-5MM-115Y PK2-5MM-101 PK2-5MM-102 www.lecroy.com 251 PROBES AND PROBE ACCESSORIES PK1-5MM-112 Dual Adapter 5.0 to 0.8 mm socket PK1-5MM-111 Adapter 5.0 to 0.8 mm socket PK1-5MM-116 Flexible Adapter 5.0 to 2 mm banana plug PK1-5MM-117 Flexible Adapter 5.0 to 4 mm banana plug 7 10 M- r 5.0 -5Mapte 1 PK B Ad PC PK1-5MM-124 Spring Tip 0.38 mm PK1-5MM-109 Spring Tip 0.8 mm PK1-5MM-104 Rigid Tip 0.8 mm 3 10 l M- Too -5M ent 1 PK justm Ad Passive Probe Accessories PP005, PP009, and PP011 Series PK1-5MM-115Y PK1-5MM-115G QFP IC-Clip short down to 0.5 mm pitch ( X : 4 = yellow; 5 = green ) PK1-5MM-114Y, PK1-5MM-114G QFP IC-Clip 13 mm long down to 0.5 mm pitch ( X : 4 = yellow; 5 = green ) PK1-5MM-110 BNC Adapter 5.0 0.4 [0.02"] ] 8" ,0 "] [0 ,16 [0 4 PK1-5MM-113 Pico hook \U+2122 4.2 [0.17"] 3.5 [0.14"] 2 PK1-5MM-101 Sprung Hook II 5.0 black 8 5 .0 -10 -10 p p5 MM 5.0 lack Ca MMg Ca 5 5 b p 1 Ca ; 1 atin ion ck h t K K c c P IC P sul te bla pit In m Pro 4m 2.5 PK1-5MM-120 Ground Lead 11 cm to 0.8 mm plug PK1-5MM-123 HF Compensated Ground Lead 22 cm PK1-5MM-118 Ground Spring 5.0 6 10 s M- ing -5Ming R s 1 r PK Cod colo t Se 3x4 PK1-5MM-119 Ground Lead 11 cm to miniclip PK1-5MM-121 Ground Lead 22 cm to 2 mm banana plug PK1-5MM-122 Ground Lead 22 cm to 4 mm banana plug PK1-5MM-102 Ground Lead 11 cm P R O B E S A N D P R O B E A C C E S S O R I E S P R O B E S A N D P R O B E A C C E S S O R I E S PASSIVE PROBES The PP007 and PP008 embody leading edge technology in passive probe design. A rugged, general-purpose probe, its small size is optimized for maximum waveform fidelity. The small 2.5 mm ground sleeve provides superior visibility, as well as a greater ability to probe dense circuits than traditional 3.5 mm and 5 mm probes. Its sharp probe tip* is spring loaded, allowing it to retract into the narrow probe head. Low input capacitance and low inductance optimize functionality in high frequency applications. For best performance, the PP007-WR-1 version is designed to be used with the WaveRunner 6000A Series, while the PP007-WS-1 version is designed for the WaveSurfer 400 Series. The PP008-1 is designed for use with the WaveRunner Xi Series. PP007-WR-1 PP007-WS-1 PP008-1 Features: * Compact probe head * Fine pitch SMD probing support * Rugged, sharp tip * HF optimized connection accessories * Over 30 accessories * Low input capacitance SPECIFICATIONS ELECTRICAL CHARACTERISTICS Attenuation Bandwidth Input R Input C Max. Input Voltage / 10 > 500 MHz 10 M 9.5 pF 400 V CAT I (1250 V surge) 300 V CAT II GENERAL CHARACTERISTICS Ground Sleeve Diameter Input Pin Diameter Cable Length 2.5 mm 0.5 mm 1.3 m ORDERING INFORMATION Basic Adapter Kit Advanced Adapter Kit SMD Adapter Kit Microclip Kit /10 HiZ 500 MHz Passive Probe for WaveRunner Xi Series Oscilloscopes /10 HiZ 500 MHz Passive Probe for WaveRunner 6000A Series Oscilloscopes /10 HiZ 500 MHz Passive Probe for WaveSurfer 400 Series Oscilloscopes Instruction Manual * A rigid tip is included 252 1-800-5-LeCroy PRODUCT CODE PK701 PK702 PK703 PK704 PP008-1 PP007-WR-1 PP007-WS-1 PP007-OM-E www.lecroy.com 253 5 ,0 59 ] 1 [ 1 01 700 ap h PK IC C pitc mm wn) 1.0 (bro PK007-018 Dual Lead Adapter PK007-017 Single Lead Adapter PK007-022 Adapter, 2 mm plug PK007-023 Adapter, 4 mm plug PK007-001 Sprung Hook 2 01 700 ap h PK IC C pitc mm ck) 7 a 2 1. (bl 07 7-0 ap 00 g C PK latin u Ins n tio tec Pro p Ca Passive Probe Accessories for PP007 and PP008 Series PK007-019 Pico Hook PK007-021 Micro Clip, Short PK007-020 Micro Clip, Long [0 9] 03 0, 0 01 700 ap h PK IC C pitc mm y) 0.8 (gra PROBES AND PROBE ACCESSORIES 1, PK007-015 PCB Adapter 5,8 [0,228] 9 00 700 ap ch PK IC C pit m 5 m ue) 0.6 (bl PK007-031 BNC Adapter 8 00 700 ap h PK IC C pitc mm en) 0.5 (gre DEVICE UNDER TEST PK007-014 10 Copper Pads ( 2 x 2 cm ) PK007-004 Rigid Tip 0.5 mm PK007-005 Spring Tip 0.5 mm 03 l 7-0 Too 00 ent K P stm ju Ad PK007-024 Probe Tip Ground Lead with 0.8 mm Socket PK007-025 Probe Tip Ground Lead with Alligator Clip PK007-013 Ground Blade PK007-016 Ground Spring C PK007-027 Ground Lead with 8 mm socket PK007-026 Ground Lead with mini clip PK007-028 Ground Lead with 2 mm plug PK007-029 Ground Lead with 4 mm plug PK007-002 Standard Ground Lead PK007-030 High Frequency Compensated Ground Lead 06 g s 7-0 Rin 00 ng PK Codi t) r (s e olo P R O B E S A N D P R O B E A C C E S S O R I E S P R O B E S A N D P R O B E A C C E S S O R I E S PASSIVE PROBE ACCESSORIES ORDERING INFORMATION PP007 AND PP008 PROBE ACCESSORIES PK701 Sprung Hook 2 Standard Ground Lead 2 Adjustment Tool 1 Rigid Tip 2 Spring Tip 2 Color Coding Rings (3 Red, 3 Yellow, 3 Blue, 3 Green) Insulating Cap IC-cap for 0.5 mm Pitch IC-cap for 0.65 mm Pitch IC-cap for 0.8 mm Pitch IC-cap for 1.0 mm Pitch IC-cap for 1.27 mm Pitch Ground Blade Copper Pad PCB-adapter Ground Spring 2 Single Adapter Lead Dual Adapter Lead Pico Hook Microclip Long 0.5 mm Microclip Short 0.5 mm Adapter 2 mm Plug Adapter 4 mm Plug Probe Tip Ground Lead w/0.8 mm Socket Probe Tip Ground Lead w/Alligator-clip Ground Lead with Miniclip Ground Lead with 0.8 mm Socket Ground Lead with 2 mm Plug Ground Lead with 4 mm Plug HF-compensated Ground Lead BNC-adapter Product Description Brochure 1 254 1-800-5-LeCroy PRODUCT CODE PK702 1 1 1 2 1 2 2 1 1 1 1 1 1 1 5 1 PK703 PK704 PK007-001 PK007-002 PK007-003 PK007-004 PK007-005 PK007-006 2 2 2 2 2 2 2 2 2 1 1 2 2 2 1 1 1 1 1 1 1 2 2 1 1 PK007-007 PK007-008 PK007-009 PK007-010 PK007-011 PK007-012 PK007-013 PK007-014 PK007-015 PK007-016 PK007-017 PK007-018 PK007-019 PK007-020 PK007-021 PK007-022 PK007-023 PK007-024 PK007-025 1 1 1 2 1 1 1 1 1 PK007-026 PK007-027 PK007-028 PK007-029 PK007-030 PK007-031 PK007-032 P R O B E S A N D P R O B E A C C E S S O R I E S ACTIVE VOLTAGE PROBES ZS SERIES HIGH IMPEDANCE ACTIVE PROBES The ZS Series probes provide high impedance and an extensive set of probe tips and ground accessories to handle a wide range of probing scenarios. The high 1 M input resistance and low 0.9 pF input capacitance mean this probe is ideal for all frequencies. The ZS Series probes provide full system bandwidth for all LeCroy oscilloscopes having bandwidths of 1 GHz and lower. HIGH IMPEDANCE REDUCES CIRCUIT LOADING ACROSS FULL OSCILLOSCOPE BANDWIDTH Engineers must commonly probe high frequency signals with high signal fidelity. Typical passive probes with high input R and C provide good response at lower frequencies, but inappropriately load the circuit, and distort signals, at higher frequencies. The ZS Series features both high input R (1 M) and low input C (0.9 pF) to reduce circuit loading across the entire probe/oscilloscope bandwidth. With low circuit loading, and a form factor that allows probing in confined areas, the ZS Series becomes the everyday probe for all different types of signals and connection points. The ZS1000 is ideal for 200-600 MHz oscilloscopes. The ZS1500 is ideal for 1 GHz oscilloscopes. ZS1500 ZS1000 www.lecroy.com 255 PROBES AND PROBE ACCESSORIES Passive probes are great for low frequency measurements; however, the input capacitance reduces impedance above 1 kHz. The 1 M input resistance and 0.9 pF capacitance of the ZS probe provide high impedance across the entire probe bandwidth making it the ideal tool for all your probing needs. P R O B E S A N D P R O B E A C C E S S O R I E S ACTIVE VOLTAGE PROBES A VARIETY OF PROBE TIPS FOR VARIED TASKS Engineers often need to probe a variety of different test points in confined spaces. The extensive range of standard and optional tip accessories for the ZS Series of probes ensures that this probe can meet any difficult probing challenge. Various flexible leads and clips, such as right-angle leads, Y-adapters, and pico hooks, are also available for probing test points that are spaced farther apart. INNOVATIVE GROUNDING SOLUTIONS PROVIDE THE HIGHEST SIGNAL FIDELITY AND EASIEST CONNECTIONS Making a good ground connection is just as Keeping the ground loop short is critical to eliminating the effect of high inductance on the signal. The ZS Series of probes provides several grounding capabilities to offer the highest signal fidelity by shortening the ground loop and eliminating the effect of that loop on the signal. The standard Offset ground lead is a "twisted-Z" shape for probing signal and ground points that are extremely close together. The standard ground blade and copper pad provide the shortest ground loop possible, and provide a pulse response that cannot be achieved with traditional long ground leads. A variety of other ground connections are available for nearly any type of probing requirement. SPECIFICATIONS ELECTRICAL CHARACTERISTICS Bandwidth (probe only) Bandwidth (system) ZS1000 ZS1500 Input Capacitance DC Input Resistance Probe Offset Range Attenuation Input Dynamic Range Non-Destruct Voltage 1 GHz 600 MHz at probe tip with 600 MHz oscilloscope 0.9 pF 1 M NA /10 8 V 20 V 1.5 GHz 1 GHz at probe tip with 1 GHz oscilloscope 0.9 pF 1 M 12 V /10 8 V 20 V GENERAL CHARACTERISTICS Cable Length 1.3 m 1.3 m INCLUDED WITH STANDARD CONFIGURATION Instruction Manual, English Color Coding Clips (set of 4 colors) Certificate of Calibration 1-Year Warranty Straight Probe Tip (PK-ZS-001) 4 Offset Ground (PK-ZS-002) 2 Short Lead (PK-ZS-003) 1 Long Lead (PK-ZS-004) 1 Y Lead Adapter (PK-ZS-005) 1 Right Angle Connector (PK-ZS-006) 1 Sprung Hook Red (PK-ZS-007R) 1 Sprung Hook Black (PK-ZS-007B) 1 Ground Blade (PK-ZS-008) 1 Copper Pad (PK-ZS-009) 2 Color Coding Rings (PK-ZS-010) 4 (sets) 256 1-800-5-LeCroy 4 2 1 1 1 1 1 1 1 2 4 (sets) P R O B E S A N D P R O B E A C C E S S O R I E S ACTIVE VOLTAGE PROBES EXTENSIVE SET OF PROBE TIPS AND GROUND LEADS FOR A WIDE RANGE OF PROBING SCENARIOS The Straight Tip and Offset Ground Lead can be used together for probing signal and ground points extremely close together. Hard-to-reach spaces can be be probed with the Bent Sharp Tip and can be used with a range of ground leads like the flexible Short Right-angle Lead shown here. Probe directly on surface mount components, like resistors or capacitors, with the Discrete SMD Tip. Use this tip with any of the ground leads, like the flexible Long Right-angle Lead shown here. Use the Right-angle Connector and the Sprung Hook to probe square pins spaced far apart from each other. The Ground Blade and Copper Pad provide the shortest ground loop for excellent signal fidelity when probing an IC. Use them with the insulated IC Lead Tip to prevent shorting between test points. www.lecroy.com 257 PROBES AND PROBE ACCESSORIES Use the Solder-In Ground with Straight Tip for general purpose browsing. P R O B E S A N D P R O B E A C C E S S O R I E S ACTIVE VOLTAGE PROBES ORDERING INFORMATION (Set of 4) ZS1500 Active Probes (Set of 4) ZS1000 Active Probes 1.5 GHz, 1 M, 0.9 pF Active Probe 1 GHz, 1 M, 0.9 pF Active Probe REPLACEMENT ACCESSORIES Replacement Accessory Kit for ZS Series Probes Straight Probe Tip Offset Ground Short Lead Long Lead Y Lead Adapter Right-Angle Connector Sprung Hook - Red Sprung Hook - Black Ground Blade Copper Pad Color Coding Rings AVAILABLE ACCESSORIES IC Lead Tip Discrete SMD Tip Bent Sharp Tip Solder-In Ground Bendable Pogo Ground Ground Spring Hook Square Pin Ground Spring Short Right-angle Lead Long Right-angle Lead 258 1-800-5-LeCroy PRODUCT CODE ZS1500-QUADPAK ZS1000-QUADPAK ZS1500 ZS1000 PK-ZS PK-ZS-001 PK-ZS-002 PK-ZS-003 PK-ZS-004 PK-ZS-005 PK-ZS-006 PK-ZS-007R PK-ZS-007B PK-ZS-008 PK-ZS-009 PK-ZS-010 PACC-PT003 PACC-PT004 PACC-PT005 PACC-CD007 PACC-CD008 PACC-LD001 PACC-LD002 PACC-LD003 PACC-LD004 www.lecroy.com 259 PK-ZS-001 Standard Probe Tip PK-ZS-006 Right Angle Adapter PK-ZS-009 Copper Pad PK-ZS-002 Offset Ground PROBES AND PROBE ACCESSORIES Accessories for ZS Series High Impedance Active Probes PK-ZS-008 Ground Blade PK-ZS-010 Marker Bands, 4 colors PK-ZS-005 Y Lead Adapter PK-ZS-007R Sprung Hook, red PK-ZS-004 Ground Lead, long PK-ZS-003 Ground Lead, short PK-ZS-007B Sprung Hook, black P R O B E S A N D P R O B E A C C E S S O R I E S P R O B E S A N D P R O B E A C C E S S O R I E S ACTIVE VOLTAGE PROBES HFP2500 HFP ACTIVE PROBES LeCroy's series of HFP active probes are versatile, small and lightweight, yet still maintain the high bandwidth needed for accurate measurement. Five interchangeable tips facilitate access regardless of tight fits and difficult locations. The FreeHand probe holder brings added versatility, allowing several probes to be used at the same time on a variety of test points while maintaining the short paths needed to preserve signal fidelity. The HFP probes also offer AutoColor ID, which automatically illuminates the probe head in a connected oscilloscope's trace color. This unique capability eliminates the need to manually apply plastic rings or colored tape to determine which channel the probe is connected to. HFP1500 HFP1000 Features: * 1 GHz to 3.5 GHz bandwidth * 0.7 pF input capacitance * 8 V dynamic range * 12 V offset range (except HFP1000) * 5 interchangeable tips for probing a variety of test points * Replaceable probe tip socket * Hands-free probing with FreeHand probe holder * AutoColor ID feature matches the channel trace color SPECIFICATIONS ELECTRICAL CHARACTERISTICS BANDWIDTH (PROBE ONLY) HFP1000 HFP1500 HFP2500 Input Capacitance DC Input Resistance Input Dynamic Range Probe Offset Range Attenuation Attenuation Accuracy Output Zero Offset Accuracy (n/a for HFP1000) GENERAL CHARACTERISTICS Cable Length Probe Head Size (LWH) Input Sockets INCLUDED WITH STANDARD CONFIGURATION Instruction Manual, English Certificate of Calibration 1-year Warranty 260 1-800-5-LeCroy 1 GHz 1.5 GHz 2.5 GHz 0.7 pF at 1 GHz 100 k 8 V N/A (HFP1000) 12 V (HFP1500, HFP2500) /10 1% < 4 mV, referred to input (1% of offset value +4 mV) 1.3 m 61 mm x 7.3 mm x 13.1 mm Signal and ground sockets compatible with 0.635 mm (0.025") square pins, 0.91 mm (0.036") maximum diameter (for round pins) P R O B E S A N D P R O B E A C C E S S O R I E S ACTIVE VOLTAGE PROBES ACCESS. INCLUDED WITH STANDARD CONFIGURATION Straight Tip Sharp Tip Bent Tip Discrete SMD Tip IC Lead Tip Square Pin Ground Spring Flexible IC Ground Bendable Pogo Ground Solder-In Ground Short Single Lead Long Single Lead Right-angle Short Single Lead Right-angle Long Single Lead Clips (0.8 mm) FreeHand Probe Holder Replaceable Cartridge Microclips (0.5 mm) Low C Tip Cartridge Soft Accessory Case HFP1000 4 4 1 1 1 1 1 1 2 1 ORDERING INFORMATION 1 HFP25000 4 4 4 4 4 1 1 2 2 1 1 1 2 1 1 2 1 1 PRODUCT CODE HFP1000 HFP1500 HFP2500 PK108 PK109 PK110 SAC-01 PACC-PT001 PACC-PT002 PACC-PT003 PACC-PT004 PACC-PT005 PACC-MS001 PACC-MS002 PACC-MS003 PACC-CD007 PACC-CD008 PACC-CD009 PACC-LD001 PACC-LD002 PACC-LD003 PACC-LD004 PACC-LD005 PACC-LD006 PK006-4 PACC-CL001 HFP1000-OM-E HFP1500-OM-E HFP2500-OM-E www.lecroy.com 261 PROBES AND PROBE ACCESSORIES 1 GHz, 0.7 pF Active Probe (/10), Small Form Factor 1.5 GHz, 0.7 pF Active Probe (/10), Small Form Factor 2.5 GHz, 0.7 pF Active Probe (/10), Small Form Factor Standard Accessory Kit for HFP2500 Standard Accessory Kit for HFP1500 Standard Accessory Kit for HFP1000 Soft Accessory Case Straight Tip Sharp Tip IC Lead Tip SMD Discrete Tip Bent Sharp Tip Freehand Probe Holder Replaceable Cartridge Low C Cartridge Solder-In Ground Bendable Pogo Ground Flexible IC Ground Ground Spring Hook Square Pin Ground Spring Short Right-angle Lead Long Right-angle Lead Short Single Lead Long Single Lead 0.8 mm Clips Microclip HFP1000 Instruction Manual, English HFP1500 Instruction Manual, English HFP2500 Instruction Manual, English HFP1500 4 4 4 4 4 1 1 1 1 1 1 2 2 2 1 1 P R O B E S A N D P R O B E A C C E S S O R I E S HIGH-BANDWIDTH TRANSMISSION LINE The PP066 is a high-bandwidth passive probe designed for use with the WaveMaster and other high-bandwidth oscilloscopes with 50 input termination. This very low capacitance probe provides an excellent solution for higher frequency applications, especially the probing of transmission lines with 20-100 impedance. The PP066 accommodates a wide range of applications, including probing of analog and digital ICs commonly found in computer, communications, data storage, and other high-speed designs. PPO66 Features: * Interchangeable attenuator tips * Signal integrity at high bandwidth * Standard SMA cable connection * Ultra low capacitance SPECIFICATIONS ELECTRICAL CHARACTERISTICS Bandwidth Risetime Input C Input R Maximum Voltage Cable Length DC to 7.5 GHz < 47 ps < 0.20 pF 500 (/10 cartridge) 1000 (/20 cartridge) 15 V rms 1m The PP065 is a transmission line probe designed for use at very high frequencies. The probe's input impedance remains nearly constant over its entire frequency range. Robust to over voltage and ESD exposure, it is particularly useful in applications producing fast rising, narrow pulses with amplitudes, which exceed the dynamic range of active probes. PPO65 Features: * 1 GHz * Low capacitance * /100 1 GHz 5 k passive probe SPECIFICATIONS Input R Ohm Maximum Voltage Compatibility Bandwidth Attenuation Input Capacitance 500 22 V LCXXX, 93XX, LA314, LA354, WaveRunner, and WavePro Scopes 1 GHz 100:1 1.5 pF ORDERING INFORMATION 7.5 GHz Low Capacitance Passive Probe (/10, 1 k; /20, 500 ) 1 GHz Low Capacitance Passive Probe (/10, 5 k) INCLUDED WITH PP066 PROBE PACC-AD001 262 1-800-5-LeCroy PRODUCT CODE PP066 PP065 SMA to BNC Adapter P R O B E S A N D P R O B E A C C E S S O R I E S DIFFERENTIAL PROBES High bandwidth, excellent common-mode rejection ratio (CMRR) and low noise make these active differential probes ideal for applications such as disk drive design and failure analysis, as well as wireless and data communication design. With the ProBus interface, the AP034 and AP033 become an integral part of the oscilloscope, allowing sensitivity, offset and common-mode range to be displayed on the scope screen. Common mode sensing and input protection capabilities of the AP033 add additional functionality. Features for both probes: * 500 MHz (AP033) and 1 GHz (AP034) bandwidths * x10 gain to / 10 attenuation range (AP033) * 10,000:1 DC CMRR * Low 9 nV/Hz noise (AP033) * 1.5 pF/side input C (AP034) * 200 V/div (AP033) * Input ESD protection * Autozero feature AP034 APO33 AP034 AP033 Bandwidth Gain 1 GHz x1 (/10 and /20 with plug-on attenuators) 2% typical (probe only) 500 MHz x10, x1, /10 (/100 with plug-on /10 attenuator) 1% in x1 without external attenuator 1 M each input to ground 2 M differential between inputs 400 mV (x1) 40 mV (x10) 4 V (/10) 40 V (/100) 400 mV (x1, x10) 4 V (10) 40 V (100) 42 V peak (10) +4.2 V peak (100) DC Accuracy Input Resistance Differential Mode Range Offset Range Common-Mode Range CMRR 1 M II 1.5 pF each input to ground 2 M ll 0.85 pF between inputs 400 mV (x1) 4 V (/10) 8 V (/20) 1.6 V (x1) 16 V (10) 32 V (20) 16 V (x1) 42 V (10) +42 V (20) 70 Hz 10,000:1 (80 dB) 1 MHz 100:1 (40 dB) 100 MHz 18.1 (25 dB) 500 MHz 9:1 (19 dB) 70 Hz 10,000:1 (80 dB) 100 kHz 10,000:1 (80 dB) 1 MHz 1000:1 (60 dB) 10 MHz 100:1 (40 dB) 250 MHz 5:1 (14 dB) www.lecroy.com 263 PROBES AND PROBE ACCESSORIES SPECIFICATIONS P R O B E S A N D P R O B E A C C E S S O R I E S DIFFERENTIAL PROBES SPECIFICATIONS (CONTINUED) Warranty AP034/AP033 200 VDC continuous 1.2 m 0 C to 50 C /10 Plug-on Attenuator /20 Plug-on Attenuator (AP034 only) Plug-on AC Coupler Flex Lead Set (1) Input `Y' Lead (1) Mini Clip, 0.8 mm (3) Mini Clip, 0.5 mm (2) Ground Lead (1) Offset Pins, Round (4) Square Pin Header Strip (1) 1 year PK033 - Standard Probe Accessory Kit for AP033/AP034 Dual Lead Single Lead Offset Pin (package of 10) 0.5 mm Clip (red and black) 0.8 mm Clip (red and black) 1x6 Square Pin Header AP03X-FLEX-LEAD NA AP03X-OFFSET-PIN PK006-3 PK006-4 NA Other Accessories for AP033/AP034 AC Coupler /10 Attenuator for AP033 /10 Attenuator for AP034 /20 Attenuator for AP034 AP03X-AC-COUPLER AP033-ATTN AP034-DA10 AP034-DA20 Max. Nondestruct Voltage Cable Length Operating Temperature Standard Accessories Probe Connection Accessory Kit ORDERING INFORMATION 1 GHz Active Differential Probe (/1, /10, /20) 500 MHz Active Differential Probe (x10, /1, /10 or /100) 264 1-800-5-LeCroy PRODUCT CODE AP034 AP033 P R O B E S A N D P R O B E A C C E S S O R I E S HIGH VOLTAGE PASSIVE PROBES The PPE series includes five fixed-attenuation probes covering a range from 2 kV to 20 kV, and one switchable probe providing /10//100 attenuation for voltage inputs up to 1.2 kV. All fixed-attenuation, standard probes automatically rescale compatible LeCroy oscilloscopes for the appropriate attenuation of the probe. Features: * Safe, accurate high-voltage measurement * 1.2 kV to 20 kV HIGH-VOLTAGE PROBES SELECTION GUIDE SPECIFICATIONS Types Bandwidth Input R Input C Attenuation Maximum Probe (MHz) () (pF) Voltage Encoding PPE1.2kV* 400 50 M <6 /10 / /100 600 V/1.2 kV No PPE2kV* 400 50 M <6 /100 2 kV Yes PPE4kV* 400 50 M <6 /100 4 kV Yes PPE5kV* 400 50 M <6 /100 5 kV Yes PPE6kV* 400 50 M <6 /1000 6 kV Yes PPE20kV 100 50 M <2 /1000 20 kV Yes (40 KV peak) ORDERING INFORMATION STANDARD ACCESSORY KIT FOR PPE20KV Ground Lead (15 cm) Hook 2m 2m 2m 2m 2m 3m PPE1.2KV PPE2KV PPE4KV PPE5KV PPE6KV PPE20KV PRODUCT CODE PPE1.2KV PPE20KV PPE2KV PPE4KV PPE5KV PPE6KV PK103 PK104 PK104-1 PK104-2 PK103 PK103-1 PP005-G22 PK30x-2 PP005-BNC PP005-ST8 PP005-RT PK104-1 PK104-2 Supplied with probe: * Probe Kit: Trimming tool, ground lead, rigid tip, IC insulator, BNC adapter, tip insulator, spring hook, red crocodile clip. 4mm safety ground lead, and green/yellow crocodile clip. Probe Kit: trimming tool, and ground lead with a crocodile clip. www.lecroy.com 265 PROBES AND PROBE ACCESSORIES /10//100; 200/300 MHz; 5 M/50 M High-Voltage Probe 600 V/1.2 kV max. Voltage DC /1000; 100 MHz; 50 M High-Voltage Probe 20 kV (40 kV Peak) max. Voltage DC and Peak AC /100; 400 MHz; 50 M High-Voltage Probe 2 kV max. Voltage DC and Peak AC /100; 400 MHz; 50 M High-Voltage Probe 4 kV max. Voltage DC and Peak AC /100; 400 MHz; 50 M High-Voltage Probe 5 kV max. Voltage DC and Peak AC /1000; 400 MHz; 50 M High-Voltage Probe 6 kV max. Voltage DC and Peak AC Accessory Kit for PPE1.2kV, 2kV, 4kV, 5kV, and 6kV Standard Probe Accessory Kit for PPE20kV Ground Lead (15 cm) Hook Standard Probe Accessory Kit for PPE1.2kV, PPE2kV Sprung Hook (red) Ground Lead (22 cm) Crocodile Clip Probe Tip to BNC Adapter IC Insulating Tip Screw Driver Probe Tip to Banana Plug Adapter Ground Lead with Banana Plug Spring Tip (0.8 mm) Rigid Tip V2A Cable P R O B E S A N D P R O B E A C C E S S O R I E S HIGH VOLTAGE DIFFERENTIAL PROBES The AP031 is a low cost, battery operated active differential probe intended for measuring higher voltages. The differential techniques employed permit measurements to be taken at two points in a circuit without reference to the ground, allowing the oscilloscope to be safely grounded without the use of opto-isolators or isolating transformers. APO31 Features: * Safe floating measurements * 15 MHz bandwidth * 700 V maximum input voltage * Works with any 1 M input oscilloscope SPECIFICATIONS Attenuation Bandwidth Input R Differential Mode Range Common Mode Range CMRR Power Source (four AA batteries) ORDERING INFORMATION /10 / /100 15 MHz 4 M 70 V / 700 V DC + Peak AC 700 V DC + Peak AC 86 dB @ 50 Hz 56 dB @ 200 kHz PRODUCT CODE 700 V, 15 MHz Differential Probe (/10, /100) ADP30X high-voltage active probes are safe, easy-to-use, and ideally suited for measuring power electronics. The ADP300 is designed for troubleshooting low-frequency power devices and other circuits where the reference potential is elevated from the ground or the location of the ground is unknown. The ADP305 is designed for measuring the high-speed floating voltages found in today's power electronics. ADP305 ADP300 266 1-800-5-LeCroy Features: * 20 MHz and 100 MHz bandwidth * 1,000 V rms common mode voltage * 1,400 V peak differential voltage * EN 61010 CAT III * 80 dB CMRR at 50/60 Hz * ProBus system * Full remote control AP031 P R O B E S A N D P R O B E A C C E S S O R I E S HIGH VOLTAGE DIFFERENTIAL PROBES SPECIFICATIONS ELECTRICAL CHARACTERISTICS Bandwidth Interface 20 MHz (ADP300) 100 MHz (ADP305) 1,400 V peak 1,000 V rms CAT III 1% of Reading 50/60 Hz 80 dB (10,000:1) 100 kHz 50 dB (300:1) 60,000 V/s (ADP300) 300,000 V/s (ADP305) 50 mV rms /100//1000 (automatically selected by scope) Between inputs 8 M, 6 pF Each input to ground 4 M, 1 pF 1 V/div to 350 V/div (ADP300) 200 mV/div to 350 V/div (ADP305) ProBus, 1 M* GENERAL CHARACTERISTICS Overall Length Input Connectors Operating Temperature Warranty 2m 4 mm Shrouded Banana Plug 0 C to 50 C 1 year Differential Voltage Common Mode Voltage Low-Frequency Accuracy (probe only) CMRR Max. Slew Rate (referenced to input) AC Noise (referenced to input) Attenuation Input Impedance Sensitivity STANDARD ACCESSORIES ADP305 All ADP300 Accessories Safety Spade (1 Red, 1 Blue) Plunger Clamp Clip (1 Red, 1 Blue) Plunger Jaw Clip (1 Red, 1 Blue) Safe Alligator Clip (1 Red, 1 Blue) Soft Accessory Case ADP300 *Requires AP-1M for oscilloscopes with 50 only inputs ORDERING INFORMATION PRODUCT CODE 1,400 V, 100 MHz High-Voltage Differential Probe 1,400 V, 20 MHz High-Voltage Differential Probe ADP305 ADP300 www.lecroy.com 267 PROBES AND PROBE ACCESSORIES Instruction Manual Certification of Calibration Plunger Hook Clip (1 Red, 1 Blue) Straps for Holding Probe P R O B E S A N D P R O B E A C C E S S O R I E S CURRENT PROBES Accurately measure AC, DC, and impulse currents. MEASURE CURRENTS IN A WIDE RANGE OF APPLICATIONS Measuring AC and DC Currents LeCroy current probes do not require the breaking of a circuit or the insertion of a shunt to make accurate and reliable current measurements. Based on a combination of Hall effect and transformer technology, LeCroy current probes are ideal for making accurate AC, DC, and impulse current measurements. Fully Integrated with Oscilloscope Many current probes require external power supplies or amplifiers to display a waveform on the oscilloscope screen. All LeCroy current probes are powered through the LeCroy ProBus connection and require no additional hardware. Along with providing power, the ProBus connection allows the current probe and oscilloscope to communicate, resulting in current waveforms automatically displayed on screen in Amps, and calculated power traces scaled correctly in Watts. This full integration also allows for Degauss and Autozero functions to be done directly from the oscilloscope with a single button press. Applications LeCroy current probes are available in a wide range of models for a wide range of applications. The full range of LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 10 mA/div. Multiple current probes can be used together to make measurements on three-phase systems, or a single current probe can be used with a voltage probe to make accurate instantaneous power measurements. LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies. 268 1-800-5-LeCroy P R O B E S A N D P R O B E A C C E S S O R I E S CURRENT PROBES CP031 - 30A, 100 MHz The CP031 is LeCroy's highest bandwidth current probe. Along with the high 100 MHz bandwidth the CP031can probe continuous currents of 30 Arms and peak currents up to 50 A. The CP031 features a small form factor making it easier to probe on a crowded, compact board. Features: * 100 MHz bandwidth * Small form factor accommodates large conductors with small jaw size * 30 Arms continuous current, 50 Apeak current CP031 CP030 - 30 A, 50 MHz The CP030 was designed with a small form factor for today's crowded boards. The small jaw can probe currents in tight spaces and still clamp onto conductors up to 5 mm in diameter. Continuous currents of 30 A rms and peak currents of 50 A can be measured by the CP030, which also features a 50 MHz bandwidth. Features: * Small form factor accommodates large conductors with small jaw size * 30 Arms continuous current, 50 MHz bandwidth * 50 Apeak current AP015 - 30 A, 50 MHz The AP015 current probe can measure continuous current of 30 A rms and peak pulses of up to 50 A for durations up to 10 seconds. This probe also features an overheating protection circuit, which will display an on-screen warning to the user to prevent damage. A probe unlock detection feature is also built in to the AP015 to ensure accurate measurements. CP030 AP015 Features: * 30 Arms continuous current, 50 MHz bandwidth * 50 Apeak current for up to 10 seconds * Overheating and Probe Unlock Detection CP150 CP500 - 500 A, 2 MHz Features: * 500 Arms continuous current * 700 Apeak * 2 MHz bandwidth CP500 www.lecroy.com 269 PROBES AND PROBE ACCESSORIES CP150 - 150 A, 10 MHz Features: * 150 Arms continuous current * 500 Apeak * 10 MHz bandwidth P R O B E S A N D P R O B E A C C E S S O R I E S CURRENT PROBES SPECIFICATIONS CP031* CP030* ELECTRICAL CHARACTERISTICS Max. Continuous Input Current Bandwidth Max. Peak Current at Pulse Width Rise Time (typical) Minimum Sensitivity Max. In-Phase Current Low-Frequency Accuracy AC Noise Coupling 30 A 100 MHz 50 A 10 s 3.5 ns 20 mA/div - 1% 2.5 mA AC, DC, GND 30 A 50 MHz 50 A 10 s 7 ns 20 mA/div - 1% 2.5 mA AC, DC, GND GENERAL CHARACTERISTICS Cable Length Weight Max. Conductor Size (diameter) Interface Usage Environment Operating Temperature Max. Relative Humidity Max. Altitude Maximum Insulated Wire Voltage 1.5 m 240 g 5 mm ProBus, 1 M only Indoor 0 C to 40 C 80% 2000 m 300 V CAT I, 150 V CAT II 1.5 m 240 g 5 mm ProBus, 1 M only Indoor 0 C to 40 C 80% 2000 m 300 V CAT I * Guaranteed at 23 C 3 C The CP031 and CP030 are compatible with LeCroy X-Stream oscilloscopes running firmware version 4.3.1.1 or greater. Requires AP-1M for use with 50 input only oscilloscopes. ORDERING INFORMATION 30 A; 100 MHz Current Probe - AC/DC; 30 Arms; 50 Apeak Pulse 30 A; 50 MHz Current Probe - AC/DC; 30 Arms; 50 Apeak Pulse 30 A; 50 MHz Current Probe - AC/DC; 30 Arms; 50 Apeak Pulse 150 A; 10 MHz Current Probe - AC/DC; 150 Arms; 500 Apeak Pulse 500 A; 2 MHz Current Probe - AC/DC; 500 Arms; 700 Apeak Pulse PRODUCT CODE CP031 - 30 A, 100 MHz CP031 CP030 35 35 30 30 25 25 20 20 Current (Arms) Current (Arms) 15 AP015 CP030 - 30 A, 50 MHz 15 10 10 5 5 CP150 0 0 Frequency (Hz) CP500 Frequency (Hz) Maximum Input Current vs. Frequency Maximum Input Current vs. Frequency CP031 - 30 A, 100 MHz CP030 - 30 A, 50 MHz 10 10 1 1 Insertion Impedance () Insertion Impedance () 0.1 0.1 0.01 0.01 0.001 0.001 Frequency (Hz) Insertion Impedance vs. Frequency (typical) 270 1-800-5-LeCroy Frequency (Hz) Insertion Impedance vs. Frequency (typical) P R O B E S A N D P R O B E A C C E S S O R I E S CURRENT PROBES AP015 CP150 CP500 30 A 50 MHz 50 A 10 s 7 ns 10 mA/div - 1% AC, DC, GND 150 A 10 MHz 500 A 30 s < 35 ns 200 mA/div 500 A 1% 25 mA AC, DC, GND 500 A 2 MHz 700 A < 175 ns 200 mA/div 1150 A 1% 25 mA AC, DC, GND 2m 300 g 5 mm ProBus, 1 M only Indoor 0 C to 40 C 80% 2000 m 300 V CAT I 2m 500 g 20 mm ProBus, 1 M only Indoor 0 C to 40 C 80% 2000 m 600 V CAT II, 300 V CAT III 6m 630 g 20 mm ProBus, 1 M only Indoor 0 C to 40 C 80% 2000 m 600 V CAT II, 300 V CAT III * Guaranteed at 23 C 3 C The CP031 and CP030 are compatible with LeCroy X-Stream oscilloscopes running firmware version 4.3.1.1 or greater. Requires AP-1M for use with 50 input only oscilloscopes. CP150 - 150 A, 10 MHz CP500 - 500 A, 2 MHz 160 140 120 100 Current (A rms) Current 80 (A rms) 60 550 500 450 400 350 300 250 200 150 100 50 0 40 20 10 0 10 1 10 k 100 k 1M 10 M CP500 - 500 A, 2 MHz 0.100 Insertion Impedance 1 0.1 Insertion Impedance ( ) Insertion Impedance 0.1 0.010 0.01 0.01 0.001 0.001 0.001 Frequency (Hz) Frequency (Hz) Frequency (Hz) Insertion Impedance vs. Frequency (typical) Insertion Impedance vs. Frequency (typical) Insertion Impedance vs. Frequency (typical) www.lecroy.com 271 PROBES AND PROBE ACCESSORIES CP150 - 150 A, 10 MHz 1k Maximum Input Current vs. Frequency Maximum Input Current vs. Frequency AP015 - 30 A, 50 MHz 100 Frequency (Hz) Frequency (Hz) P R O B E S A N D P R O B E A C C E S S O R I E S PROBE DESKEW AND CALIBRATION The TF-DSQ fixture facilitates calibration of timing measurements in single-ended and differential probes--a unique concern in high-speed measurements. By requiring only one connection of a probe to the fixture and one button press, the TF-DSQ ensures probe calibration results that are valid for the duration that the probe is connected to the circuit. An extremely fast edge with 75 ps risetime combines with probe gain and offset calibration capabilities for added accuracy. TF-DSQ Features: * Deskews to 20 ps typical accuracy * Differential and single-ended drive * 75 ps edge for precise deskewing * Calibrates gain, offset and skew at the same probing point * Accounts for risetime variations * Accounts for common-mode voltage variations * DC gain calibration accounts for probe loading effects * Integrated operation with scope for fully automatic calibration SPECIFICATIONS SCOPE COMPATIBILITY (requires software version 3.6.0 or later) Scope Connection Probes Supported DC Range DC Accuracy Edge Risetime Edge Amplitude and Rep Rate Deskew Accuracy SCOPES WaveMaster (WM8420A and WM8620A including all WaveMaster XXL models) Serial Data Analyzers (SDA 18000, SDA 11000, SDA 9000, SDA 4020, and SDA 6020 including all SDA XXL models) Disk Drive Analyzers (DDA 5005A and 5005A XXL) ProLink WL600 and WL300 with all Probing Accessories PP AP033, AP034, PP066 HFP1000, HFP1500, HFP2500, ZS1500, ZS1000, D11000PS, DA18000 5 V Single-ended, 10 V Differential (1% + 600 V) 75 ps (typical) < 95 ps (guaranteed) Approximately 800 mV @ 10 MHz 20 ps (typical) ORDERING INFORMATION Probe Deskew and Calibration Fixture Included: ProLink Extender 48" 50 ohm Cable with Male SMA Connectors Calibration Certificate Operator's Manual Soft Accessory Case 272 1-800-5-LeCroy PRODUCT CODE TF-DSQ P R O B E S A N D P R O B E A C C E S S O R I E S EZ PROBE POSITIONER The EZ-Probe Positioner provides stable, accurate X, Y and Z positioning in one fluid motion. Its unique 3-D joystick, with 3:1 motion reduction and single-clutch, fullyarticulating arm, allow simple, precise positioning in anything from card cages to MCMs. Any current handheld probes can be easily attached, facilitating the measurement process and ensuring more precise connectivity. ORDERING INFORMATION PRODUCT CODE Cascade Microtech EZ-Probe Positioner EZ PROBE EZ PROBE ADPPS Power Adapter for AP033, AP034 and HFP1000 Active Probes; allows the probe's output to be connected to other non-ProBus test equipment, including spectrum and network analyzers. ORDERING INFORMATION PRODUCT CODE ProBus-to-BNC and Power Adapter for AP033, AP034, and HFP Series (BW limited to 1 GHz) ADPPS ADPPS TRANSIT CASE ORDERING INFORMATION Soft Accessory Case for Probes PRODUCT CODE SAC-01 SAC-01 www.lecroy.com 273 PROBES AND PROBE ACCESSORIES Soft Accessory Case for probes--features inside flap for storing manuals, plus roomy interior for a probe and its many accessories. Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Teledyne LeCroy: PK007-015 PK007-018 PK116-1 PKIT2-5MM-101 PP005-GL22 PK116 ADPPS PK007-030