5-Bit Programmable Synchronous Switching Regulator Controller for Pentium(R) II Processor ADP3152 a FEATURES 5-Bit Digitally Programmable 1.8 V to 3.5 V Output Voltage Dual N-Channel Synchronous Driver Total Output Accuracy 61% (08C to 708C) High Efficiency Current-Mode Operation Short Circuit Protection Power Good Output Integrated Overvoltage Protection Crowbar 16-Lead SOIC Package VRM 8.2 Compatible GENERAL DESCRIPTION The ADP3152 is a highly efficient synchronous switching regulator controller optimized for Pentium II Processor applications where 5 V is stepped down to a digitally controlled output voltage between 1.8 V and 3.5 V. Using a 5-bit DAC to read a voltage identification (VID) code directly from the processor, the ADP3152 uses a current mode constant off-time architecture to generate its precise output voltage. The ADP3152 drives two N-channel MOSFETS in a synchronous rectified buck converter, at a maximum switching frequency of 250 kHz. Using the recommended loop compensation and guidelines, the ADP3152 provides a dc/dc converter that meets Intel's stringent transient specifications with a minimum number of output capacitors and smallest footprint. Additionally, the current mode architecture also provides guaranteed short circuit protection and adjustable current limiting. APPLICATIONS Desktop PC Power Supply for: Pentium II Processor Pentium Pro Processor Pentium Processor AMD-K6 Processor VRM Modules VCC +12V VIN +5V + 1mF 22mF CIN VCC DRIVE1 SD R1 ADP3152 IRL3103 L 2.5mH RSENSE 6.7mV CMP R2 CCOMP + SENSE+ 1nF CT CO VO 1.8V-3.5V 14A SENSE- 150pF AGND 10BQ015 DRIVE2 IRL3103 PGND VID0-VID4 5-BIT CODE Figure 1. Typical Application Pentium is a registered trademark of Intel Corporation. All other trademarks are the property of their respective holders. REV. 0 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 World Wide Web Site: http://www.analog.com Fax: 781/326-8703 (c) Analog Devices, Inc., 1998 ADP3152-SPECIFICATIONS (08C T +708C, V A Parameter CC = 12 V, VIN = 5 V, unless otherwise noted) Symbol Conditions Min VO With Respect to Nominal Output Voltage (Figure 13) -1.0 -1.0 -1.0 OUTPUT VOLTAGE LINE REGULATION VO ILOAD = 10 A (Figure 2) VIN = 4.75 V to 5.25 V 0.05 % OUTPUT VOLTAGE LOAD REGULATION VO (Figure 2) 200 mA < ILOAD < 14 A 0.1 % IQ VSD = 0.8 V TA = +25C, VID Pins Floating 3.7 140 4.5 250 mA A V8-V7 V7 Forced to VOUT - 3% 145 165 mV 0.6 V V 220 A OUTPUT ACCURACY 1.8 V Output Voltage 2.8 V Output Voltage 3.5 V Output Voltage Typ Max Units 1.0 1.0 1.0 % % % 1 INPUT DC SUPPLY CURRENT Normal Mode Shutdown CURRENT SENSE THRESHOLD VOLTAGE VID PINS THRESHOLD Low High V16, V1-V4 VID PINS INPUT CURRENT I16, I1-I4 VID0-VID4 PULL-UP RESISTANCE RVID CT PIN DISCHARGE CURRENT I9 125 2.0 VID = 0 V 110 20 TA = +25C VOUT in Regulation VOUT = 0 V k 65 2 10 A A 2.45 3.2 s OFFTIME tOFF CT = 150 pF DRIVER OUTPUT TRANSITION TIMES tR, tF CL = 7000 pF (Pins 13, 14) TA = +25C 120 200 ns POSITIVE POWER GOOD TRIP POINT VPWRGD Output Coming Into Regulation 5 8 % NEGATIVE POWER GOOD TRIP POINT VPWRGD Output Coming Into Regulation POWER GOOD RESPONSE TIME tPWRGD CROWBAR TRIP POINT VCROWBAR ERROR AMPLIFIER OUTPUT IMPEDANCE ROERR 145 k ERROR AMPLIFIER TRANSCONDUCTANCE GMERR 2.2 mmho ERROR AMPLIFIER MINIMUM OUTPUT VOLTAGE VCMPMIN V7 Forced to VOUT + 3% 0.8 V ERROR AMPLIFIER MAXIMUM OUTPUT VOLTAGE VCMPMAX V7 Forced to VOUT - 3% 2.4 V ERROR AMPLIFIER BANDWIDTH -3 dB BWERR CMP = Open 500 kHz SHUTDOWN (SD) PIN Low Threshold High Threshold Input Current SDL SDH SDIB Part Active Part in Shutdown % Above Output Voltage 1.8 30 -8 9 -5 % 500 s 15 24 0.6 2.0 10 % V V A NOTES 1 Dynamic supply current is higher due to the gate charge being delivered to the external MOSFETS. All limits at temperature extremes are guaranteed via correlation using standard quality control methods. Specifications are subject to change without notice. -2- REV. 0 ADP3152 PIN FUNCTION DESCRIPTIONS Pin Mnemonic Function 1-4, 16 VID1-VID4, VD0 5 6 AGND SD 7 SENSE- 8 SENSE+ 9 10 CT CMP 11 PWRGD 12 13 VCC DRIVE2 14 DRIVE1 15 PGND Voltage Identification DAC Input Pins. These pins are internally pulled up to VREG providing a logic one if left open. Leaving all five DAC inputs open results in placing the ADP3152 into shutdown. Analog Ground Pin. This pin must be routed separately to the (-) terminal of COUT. Shutdown Pin. A logic high will place the ADP3152 in shutdown and disable the output. This pin is internally pulled down. Connects to the internal resistor divider which, along with the VID code, sets the output voltage. Pin 7 is also the (-) input for the current comparator. The (+) input for the current comparator. A threshold between Pins 8 and 7 set by the error amplifier in conjunction with RSENSE, sets the current trip point. External Capacitor CT from Pin 9 to ground sets the off time of the device. Error Amplifier Compensation Point. The current comparator threshold increases with the Pin 10 voltage. Power Good Pin. An open drain signal to indicate that the output voltage is within a 5% regulation band. Input Voltage Pin. Gate Drive for the bottom synchronous N-channel MOSFET. The voltage at Pin 13 swings from ground to VCC. Gate Drive for the top primary N-channel MOSFET. The voltage at Pin 14 swings from ground to VCC. Driver Power Ground. Connects to the source of the bottom N-channel MOSFET and to the (-) terminal of CIN. PIN CONFIGURATION ABSOLUTE MAXIMUM RATINGS* Input Supply Voltage (Pin 12) . . . . . . . . . . . . -0.3 V to +16 V VID0-VID4, SD, PWRGD, CMP, CT . . . . . . . -0.3 V to VCC DRIVE1, DRIVE2, SENSE+, SENSE- . . . . . . -0.3 V to VCC Operating Temperature Range . . . . . . . . . . . . . 0C to +70C Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . 150C JA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110C/W Storage Temperature Range . . . . . . . . . . . . -65C to +150C Lead Temperature Range (Soldering 10 sec) . . . . . . . . +300C VID1 1 16 VID0 VID2 2 15 PGND VID3 3 14 DRIVE1 4 ADP3152 DRIVE2 VID4 TOP VIEW AGND 5 (Not to Scale) 12 VCC *This is a stress rating only; operation beyond these limits can cause the device to be permanently damaged. 13 SD 6 11 PWRGD SENSE- 7 10 CMP SENSE+ 8 9 CT ORDERING GUIDE Model Temperature Package Range Description Package Option ADP3152AR 0C to +70C 16-Lead SOIC R-16A/SO-16 CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the ADP3152 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. REV. 0 -3- WARNING! ESD SENSITIVE DEVICE ADP3152 22V 100kV 3 32700mF/10V + + mP SYSTEM 1 2 3 4 5 6 7 8 + + + 1mF 22mF VCC + 12V L2 1.7mH VIN + 5V +5V RTN 1mF +12V RTN ADP3152 VID1 VID0 VID2 PGND VID3 DRIVE1 VID4 DRIVE2 VCC AGND SD PWRGD SENSE- CMP SENSE+ CT 16 IRL3103 L1 2.5mH 15 RSENSE 6.7mV 2700mF 3 6 (10V) 14 IRL3103 13 + 10BQ015 + + + + + VO 1.8V-3.5V 0-14A 12 RTN R1 150kV 11 10 2nF R2 39kV 9 CCOMP CT 150pF 220V 1nF 220V Figure 2. Typical Application for Pentium II VCC DRIVE1 DRIVE2 PGND AGND 12 14 13 15 PWRGD SENSE+ SENSE- 11 8 7 5 ADP3152 DELAY VREF + 15% REFERENCE NONOVERLAP DRIVE SD 6 2R IN CROWBAR 1.20V VREF + 5% VREF - 5% 16 VID0 1 VID1 2 VID2 3 VID3 4 VID4 CMPI S Q VT1 R gm VT2 CMPT VREF R OFF-TIME CONTROL DAC SENSE- 9 10 CT CMP Figure 3. Functional Block Diagram -4- REV. 0 Typical Performance Characteristics-ADP3152 100 45 400 VOUT = +3.5V 40 85 VOUT = +2.8V 80 75 FREQUENCY - kHz 350 90 VOUT = +2.0V GATE CHARGE CURRENT - mA 95 EFFICIENCY - % 450 SEE FIGURE 2 300 250 200 150 100 70 50 Figure 4. Efficiency vs. Output Current 30 25 Qn + Qn = 100nC 20 15 10 5 0 50 65 1.4 2.8 4.2 5.6 7.0 8.4 9.8 11.2 12.6 14.0 OUTPUT CURRENT - Amps 35 0 100 200 300 400 500 600 700 800 TIMING CAPACITOR - pF Figure 5. Frequency vs. Timing Capacitor 45 58 83 134 OPERATING FREQUENCY - kHz 397 Figure 6. Gate Charge Supply Current vs. Operating Frequency SEE FIGURE 2 SEE FIGURE 2 VOUT = +3.5V, IOUT = 10A PRIMARY N-DRIVE DRIVER OUTPUT OUTPUT VOLTAGE 20mV/DIV 1 SECONDARY N-DRIVE DRIVER OUTPUT OUTPUT CURRENT 14A TO 1A 2 2 DRIVE 1 AND 2 = 5V/DIV 100ns/DIV 500ns/DIV Figure 7. Gate Switching Waveforms Figure 8. Driver Transition Waveforms 10ms/DIV Figure 9. Transient Response, 14 A-1A of Figure 2 Circuit 25 TA = +258C SEE FIGURE 13 VCC VOLTAGE 5V/DIV OUTPUT VOLTAGE 20mV/DIV 3 REGULATOR OUTPUT VOLTAGE 1V/DIV OUTPUT CURRENT 1A TO 14A NUMBER OF PARTS 20 15 10 5 0 10ms -0.55 -0.5 -0.45 -0.4 -0.35 -0.3 -0.25 -0.2 -0.15 -0.1 -0.05 0 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45 0.5 4 OUTPUT ACCURACY - % Figure 10. Transient Response, 1A-14 A of Figure 2 Circuit REV. 0 Figure 11. Power-On Start-Up Waveforms -5- Figure 12. Output Accuracy Distribution, VOUT = 2.8 V ADP3152 causes an increase in the output of the voltage-error amplifier, which, in turn, leads to an increase in the current comparator threshold VT1, thus tracking the load current. 12V 5-BIT CODE VID0- VID4 VCC + 1mF 0.1mF DRIVE1 SD CMP 1kV ADP3152 AGND 100kV SENSE+ SENSE- CT 4700pF Table I. Output Voltage vs. VID Code DRIVE2 PGND VOUT OP27 1.2V 0.1mF Figure 13. Closed-Loop Test Circuit for Accuracy APPLICATION INFORMATION The ADP3152 uses a current-mode, constant-off-time control technique to switch a pair of external N-channel MOSFETs in a synchronous rectified buck converter application. Due to the constant-off-time operation, no slope compensation is needed. A unique feature of the constant-off-time control technique is that the converter's frequency becomes a function of the ratio of input voltage to output voltage. The off time is determined by the value of the external capacitor connected to the CT pin. The on time varies in such a way that a regulated output voltage is maintained. The output voltage is sensed by an internal voltage divider that is connected to the Sense- pin. A voltage-error amplifier gm compares the values of the divided output voltage with a reference voltage. The reference voltage is set by an onboard 5-bit DAC, which reads the code present at the voltage identification (VID) pins and converts it to a precise value between 600 mV and 1.167 V. Refer to Table I for the output voltage vs. VID pin code information. During continuous-inductor-current mode of operation, the voltage-error amplifier gm and the current comparator CMPI are the main control elements. During the on time of the high side MOSFET, the current comparator CMPI monitors the voltage between the Sense+ and Sense- pins. When the voltage level between the two pins reaches the threshold level VT1, the high side drive output is switched to zero, which turns off the high side MOSFET. The timing capacitor CT is now discharged at a rate determined by the off time controller. In order to maintain a ripple current in the inductor, which is independent of the output voltage, the discharge current is made proportional to the value of the output voltage (measured at the Sense- pin). While the timing capacitor is discharging, the low side drive output goes high, turning on the low side MOSFET. When the voltage level on the timing capacitor has discharged to the threshold voltage level VT2 , comparator CMPT resets the SR flip-flop. The output of the flip-flop forces the low side drive output to go low and the high side drive output to go high. As a result, the low side switch is turned off and the high side switch is turned on. The sequence is then repeated. As the load current increases, the output voltage starts to decrease. This VID4 VID3 VID2 VID1 VID0 VOUT 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1.80 1.80 1.80 1.80 1.80 1.80 1.80 1.80 1.80 1.80 1.80 1.85 1.90 1.95 2.00 2.05 Shutdown 2.10 2.20 2.30 2.40 2.50 2.60 2.70 2.80 2.90 3.00 3.10 3.20 3.30 3.40 3.50 To prevent cross conduction of the external MOSFETs, feedback is incorporated to sense the state of the driver output pins. Before the low side drive output can go high, the high side drive output must be low. Likewise, the high side drive output is unable to go high while the low side drive output is high. Power Good The ADP3152 has an internal monitor which monitors the output voltage and drives the PWRGD pin of the device. This pin is an open drain output whose high level (when connected to a pull-up resistor) indicates that the output voltage has been within a 5% regulation band of the targeted value for more than 500 s. The PWRGD pin will go low if the output is outside the regulation band for more than 500 s. Output Crowbar An added feature of using an N-channel MOSFET as the synchronous switch is the ability to crowbar the output with the same MOSFET. If the output voltage is 15% greater than the desired regulated value, the ADP3152 will turn on the lower MOSFET, which will current-limit the source power supply or blow its fuse, pull down the output voltage, and thus save the -6- REV. 0 ADP3152 expensive microprocessor from destruction. The crowbar function releases at approximately 50% of the nominal output voltage. For example, if the output is programmed to 2.0 V, but is pulled up to 2.3 V or above, the crowbar will turn on the lower MOSFET. If in this case the output is pulled down to less than 1.0 V, the crowbar will release, allowing the output voltage to recover to 2.0 V. The timing capacitor can be calculated from the equation: CT = tOFF x 65 A = 143 pF 1V The converter operates at the nominal operating frequency only at the above specified VO and at light load. At higher VO, and heavy load, the operating frequency decreases due to the parasitic voltage drops across the power devices. The actual minimum frequency at VO = 2.8 V is calculated to be 160 kHz (see Equation 1 below). Where Shutdown The ADP3152 has a shutdown pin which is pulled logic low by an internal resistor. In this condition the device functions normally. This pin should be pulled high externally to disable the output drives. IIN Calculation of Component Values R IN The design parameters for a typical 300 MHz Pentium II application (Figure 2) are as follows: Input voltage: VIN = 5 V Auxiliary input: VCC = 12 V Output voltage: VO = 2.8 V R DS(ON)HSF R DS(ON)LSF R SENSE Maximum output current: IOMAX = 14.2 Adc RL Minimum output current: IOMIN = 0.8 Adc is the input dc current (assuming an efficiency of 90%, IIN = 9 A) is the resistance of the input filter (estimated value: 7 m) is the resistance of the high side MOSFET (estimated value: 10 m) is the resistance of the low side MOSFET (estimated value: 10 m) is the resistance of the sense resistor (estimated value: 7 m) is the resistance of the inductor (estimated value: 6 m) C O Selection--Determining the ESR Static tolerance of the supply voltage for the processor core: VOST+ = 100 mV VOST- = -60 mV The selection of the output capacitor is driven by the required ESR and capacitance CO. The ESR must be small enough that both the resistive voltage deviation due to a step change in the load current and the output ripple voltage stay below the values defined in the specification of the supplied microprocessor. The capacitance, CO, must be large enough that the output is held up while the inductor current ramps up or down to the value corresponding to the new load current. Transient tolerance (for less than 2 s) of the supply voltage for the processor core when the load changes between the minimum and maximum values with a di/dt of 30 A/s: VOTR+ = 130 mV VOTR- = -130 mV Input current di/dt when the load changes between the minimum and maximum values: less than 0.1 A/s The total static tolerance of the Pentium II processor is 160 mV. Taking into account the 1% setpoint accuracy of the ADP3152, and assuming a 0.5% (or 14 mV) peak-to-peak ripple, the allowed static voltage deviation of the output voltage when the load changes between the minimum and maximum values is 0.08 V. Assuming a step change of I = IOMAX-IOMIN = 13.4 A, and allocating all of the total allowed static deviation to the contribution of the ESR sets the following limit: The above requirements correspond to Intel's published power supply requirements based on VRM 8.2 guidelines. C T Selection for Operating Frequency The ADP3152 uses a constant-off-time architecture with tOFF determined by an external timing capacitor CT. Each time the high side N-channel MOSFET switch turns on, the voltage across CT is reset to approximately 3.3 V. During the off time, CT is discharged by a constant current of 65 A to 2.3 V, that is by 1 V. The value of the off time is calculated from the preferred continuous-mode operating frequency. Assuming a nominal operating frequency of fNOM = 200 kHz at an output voltage of VO = 2.8 V, the corresponding off time is: RE ( MAX ) = ESRMAX 1 = 0.08 = 5.9 m 13. 4 VO 1 tOFF = 1- = 2.2 s V IN f NOM f MIN = REV. 0 1 V IN - I IN RIN - IOMAX (RDS(ON )HSF + RSENSE + RL ) -V O x = 160 kHz tOFF V IN - I IN RIN - IOMAX (RDS(ON )HSF + RSENSE + RL - RDS(ON )LSF ) -7- (1) ADP3152 The output filter capacitor must have an ESR of less than 5.9 m. One can use, for example, six FA type capacitors from Panasonic, with 2700 F capacitance, 10 V voltage rating, and 34 m ESR. The six capacitors have a total typical ESR of ~ 5 m when connected in parallel. RSENSE The value of RSENSE is based on the required output current. The current comparator of the ADP3152 has a threshold range that extends from 0 mV to 125 mV (minimum). Note that the full 125 mV range cannot be used for the maximum specified nominal current, as headroom is needed for current ripple, transients and inductor core saturation. Inductor Selection The minimum inductor value can be calculated from ESR, off time, dc output voltage and allowed peak-to-peak ripple voltage. LMIN1 = V OtOFF RE( MAX ) = 2.8 x 2.2 x 5.9 m V RIPPLE , p -p The current comparator threshold sets the peak of the inductor current yielding a maximum output current IOMAX, which equals the peak value less half of the peak-to-peak ripple current. Solving for RSENSE and allowing a margin for tolerances inside the ADP3152 and in the external component values yields: = 2.6 H 14 m The minimum inductance gives a peak-to-peak ripple current of 2.15 A, or 15% of the maximum dc output current IOMAX. RSENSE = (125 mV)/[1.2(IOMAX + IRPP/2)] = 6.8 m A practical solution is to use three 20 m resistors in parallel, with an effective resistance of about 6.7 m. The inductor peak current in normal operation is: ILPEAK = IOMAX + IRPP /2 = 15.3 A Once RSENSE has been chosen, the peak short-circuit current ISC(PK) can be predicted from the following equation: The inductor valley current is: ISC(PK) = (145 mV)/R SENSE = (145 mV)/(6.7 m) = 21.5 A ILVALLEY = ILPEAK - IRPP = 13 A The actual short-circuit current is less than the above calculated ISC(PK) value because the off time rapidly increases when the output voltage drops below 1 V. The relationship between the off time and the output voltage is: The inductor for this application should have an inductance of 2.6 H at full load current and should not saturate at the worst-case overload or short circuit current at the maximum specified ambient temperature. A suitable inductor is the CTX12-13855 from Coiltronics, which is 4.4 H at 1 A and about 2.5 H at 14.2 A. tOFF Tips for Selecting Inductor Core Ferrite designs have very low core loss, so the design should focus on copper loss and on preventing saturation. Molypermalloy, or MPP, is a low loss core material for toroids, and it yields the smallest size inductor, but MPP cores are more expensive than ferrite cores or the Kool M(R) cores from Magnetics, Inc. The lowest cost core is made of powdered iron, for example the #52 material from Micrometals, Inc., but yields the largest size inductor. With a short across the output, the off time will be about 70 s. During that off time the inductor current gradually decays. The amount of decay depends on the L/R time constant in the output circuit. With an inductance of 2.5 H and total resistance of 23 m, the time constant will be 108 s, which yields a valley current of 11.3 A and an average short-circuit current of about 16.3 A. To safely carry the short-circuit current, the sense resistor must have a power rating of at least 16.3 A2 x 6.8 m = 1.8 W. C O Selection--Determining the Capacitance The minimum capacitance of the output capacitor is determined from the requirement that the output be held up while the inductor current ramps up (or down) to the new value. The minimum capacitance should produce an initial dv/dt which is equal (but opposite in sign) to the dv/dt obtained by multiplying the di/dt in the inductor and the ESR of the capacitor. CMIN = IOMAX - IOMIN RE (di/dt ) = 14.2 - 0.8 5.9 m (2.2 / 4. 4 H ) CT x 1V VO + 2 A 360 k Current Transformer Option An alternative to using low value and high power current sense resistor is to reduce the sensed current by using a low cost current transformer and a diode. The current can then be sensed with a small-size, low cost SMT resistor. If we use a transformer with one primary and 50 secondary turns, the worst-case resistor dissipation is reduced to a fraction of a mW. Another advantage of using this option is the separation of the current and voltage sensing, which makes the voltage sensing more accurate. = 4.5 mF In the above equation the value of di/dt is calculated as the smaller voltage across the inductor (i.e., VIN-VO rather than VO) divided by the maximum inductance (4.4 H) of the CTX1213855 inductor from Coiltronics. The parallel-connected six 2700 F/10 V FA series capacitors from Panasonic have a total capacitance of 16,200 F, so the minimum capacitance requirement is met with ample margin. Power MOSFET Two external N-channel power MOSFETs must be selected for use with the ADP3152, one for the main switch, and an identical one for the synchronous switch. The main selection parameters for the power MOSFETs are the threshold voltage VGS(TH) and the on resistance RDS(ON). -8- REV. 0 ADP3152 The minimum input voltage dictates whether standard threshold or logic-level threshold MOSFETs must be used. For VIN > 8 V, standard threshold MOSFETs (VGS(TH) < 4 V) may be used. If VIN is expected to drop below 8 V, logic-level threshold MOSFETs (VGS(TH) < 2.5 V) are strongly recommended. Only logic-level MOSFETs with VGS ratings higher than the absolute maximum of VCC should be used. to modify, however, the specified RDS(ON) at the expected highest FET junction temperature of 140C by a RDS(ON) multiplier, using the graph in the data sheet. In our case: RDS(ON)MULT = 1.7 Using this multiplier, the expected RDS(ON) at 140C is 1.7 x 14 = 24 m. The high side FET dissipation is: The maximum output current IOMAX determines the RDS(ON) requirement for the two power MOSFETs. When the ADP3152 is operating in continuous mode, the simplifying assumption can be made that one of the two MOSFETs is always conducting the average load current. PDFETHS = IRMSHS2RDS(ON) + 0.5 VINILPEAKQG fMAX/IG = 3.72 W where the second term represents the turn-off loss of the FET. (In the second term, QG is the gate charge to be removed from the gate for turn-off and IG is the gate current. From the data sheet, QG is about 50 nC -70 nC and the gate drive current provided by the ADP3152 is about 1 A.) For VIN = 5 V and VO = 2.8 V, the maximum duty ratio of the high side FET is: DMAXHF = (1-fMIN x tOFF) =(1-160 kHz x 2.2 s) = 65% The low side FET dissipation is: PDFETLS = IRMSLS 2R DS(ON) = 1.7 W The maximum duty ratio of the low side (synchronous rectifier) FET is: (Note that there are no switching losses in the low side FET.) DMAXLF = 1 - DMAXHF = 35% To remove the dissipation of the chosen FETs, proper heatsinks should be used. The Thermalloy 6030 heatsink has a thermal impedance of 13C/W with convection cooling. With this heatsink, the junction-to-ambient thermal impedance of the chosen high side FET JAHS will be 13 (heatsink-to-ambient) + 2 (junction-to-case) + 0.5 (case-to-heatsink) = 15.5C/W. The maximum rms current of the high side FET is: IRMSLS = [DMAXHF (ILVALLEY 2 + ILPEAK2 + ILVALLEY ILPEAK)/3]0.5 = 11.5 Arms The maximum rms current of the low side FET is: IRMSLS = [DMAXLF (ILVALLEY2 + ILPEAK2 + ILVALLEYILPEAK)/3]0.5 = 8.41 Arms At full load and at 50C ambient temperature, the junction temperature of the high side FET is: The RDS(ON) for each FET can be derived from the allowable dissipation. If we allow 5% of the maximum output power for FET dissipation, the total dissipation will be: TJHSMAX = TA + JAHS PDFETHS = 105C A smaller heatsink may be used for the low side FET, e.g., the Thermalloy type 7141 ( = 20.3C/W). With this heatsink, the thermal impedance JALS for the low side FET = 33.8C/W. PFETALL = 0.05 VO IOMAX = 2 W Allocating two-thirds of the total dissipation for the high side FET and one-third for the low side FET, the required minimum FET resistances will be: The low side FET junction temperature is: TJLSMAX = TA + JALS PDFETLS = 106C RDS(ON)HSF(MIN) = 1.33/11.52 = 10 m RDS(ON)LSF(MIN) = 0.67/8.412 = 9.5 m All of the above calculated junction temperatures are safely below the 175C maximum specified junction temperature of the selected FET. Note that there is a tradeoff between converter efficiency and cost. Larger FETs reduce the conduction losses and allow higher efficiency but lead to increased cost. If efficiency is not a major concern the Fairchild MOSFET NDP6030L or International Rectifier IRL3103 is an economical choice for both the high side and low side positions. Those devices have an R DS(ON) of 14 m at VGS = 10 V and at 25C. The low side FET is turned on with at least 10 V. The high side FET, however, is turned on with only 12 V - 5 V = 7 V. If we check the typical output characteristics of the device in the data sheet, we find that for an output current of 10 A, and at a VGS of 7 V, the VDS is 0.15 V, which gives a RDS(ON) = VDS/ID = 15 m. This value is only slightly above the one specified at a VGS of 10 V, so the resistance increase due to the reduced gate drive can be neglected. We have REV. 0 The maximum operating junction temperature of the ADP3152 is calculated as follows: TJICMAX = TA + JA (IICVCC + PDR) where JA is the junction to ambient thermal impedance of the ADP3152 and PDR is the drive power. From the data sheet, JA is equal to 110C/W and IIC = 2.7 mA. PDR can be calculated as follows: PDR = (CRSS + CISS)VCC2 fMAX = 307 mW The result is: TJICMAX = 86C -9- ADP3152 C IN Selection and Input Current di/dt Reduction In continuous-inductor-current mode, the source current of the high side MOSFET is a square wave with a duty ratio of VO/ VIN. To keep the input ripple voltage at a low value, one or more capacitors with low equivalent series resistance (ESR) and adequate ripple-current rating must be connected across the input terminals. The maximum rms current of the input bypass capacitors is: ICINRMS [VO (VIN - VO)]0.5 IOMAX /VIN = 7 Arms Let us select the FA-type capacitor with 2700 F capacitance and 10 V voltage rating. The ESR of that capacitor is 34 m and the allowed ripple current at 100 kHz is 1.94 A. At 105C we would need to connect at least four such capacitors in parallel to handle the calculated ripple current. At 50C ambient, however, the ripple current can be increased, so three capacitors in parallel are adequate. The ripple voltage across the three paralleled capacitors is: VCINRPL = IOMAX [ESRIN /3 + DMAXHF /(3CIN fMIN )] <140 mV p-p To further reduce the effect of the ripple voltage on the system supply voltage bus and to reduce the input-current di/dt to below the recommended maximum of 0.1 A/s, an additional small inductor (L > 1.7 H @ 10 A) should be inserted between the converter and the supply bus (see Figure 2). Feedback Loop Compensation Design To keep the peak-to-peak output voltage deviation as small as possible, the low frequency output impedance (i.e., the output resistance) of the converter should be made equal to the ESR of the output capacitor. That can be achieved by having a single-pole roll-off of the voltage gain of the gm error amplifier, where the pole frequency coincides with the ESR zero of the output capacitor. A gain with single-pole roll-off requires that the gm amplifier is terminated by the parallel combination of a resistor and capacitor. The required resistor value can be calculated from the equation: 36 x RSENSE ( g m 145 kiRCOMP ) In the application circuit we tested, we found that the compensation scheme shown in Figure 2 gave the optimal response to meet the Pentium II dc/dc static and transient specifications with sufficient margins including the ADP3152's initial error tolerance, the PCB layout trace resistances, and the external component parasitics. If we increase the load resistance to the COMP pin, the static regulation will improve. The load transient response, however, will get worse. In Figure 2, if we decrease the R1 = 150 k resistor vs. the R2 = 39 k resistor, the regulation band will shift positive in relation to the 2.8 V. If we increase the R1 resistor, the regulation band will shift negative. It may be necessary to adjust these resistor values to obtain the best static and dynamic regulation compliance depending on the output capacitor ESR and the parasitic trace resistances of the PCB layout. BOARD LAYOUT A multilayer PCB is recommended with a minimum of two copper layers. One layer on top should be used for traces interconnecting low power SMT components. The ground terminals of those components should be connected with vias to the bottom traces connecting directly to the ADP3152 ground pins. One layer should be a power ground plane. If four layers are possible, one additional layer should be an internal system ground plane, and one additional layer can be used for other system interconnections. When laying out the printed circuit board, the following checklist should be used to ensure proper operation of the ADP3152. It is advisable to follow the evaluation board layout as closely as possible. If necessary, contact Analog Devices Application Engineering for layout suggestions. = RE where gm = 2.2 ms and the quantities 36 and 145 k are characteristic of the ADP3152. The calculated compensating resistance is: R1iR2 = RCOMP = 31 k The compensating capacitance is determined from the equality of the pole frequency of the error amplifier gain and the zero frequency of the impedance of the output capacitor. CCOMP = RE COUT RCOMP = 5 m x 16.2 mF = 2.6 nF 31 k -10- REV. 0 ADP3152 FET, a low voltage 1 A Schottky diode can be connected between the input of the buck inductor and the source of the low side FET. Board Layout Guidelines 1. The power loop should be routed on the PCB to encompass small areas to minimize radiated switching noise energy to the control circuit and thus to avoid circuit problems caused by noise. This technique also helps to reduce radiated EMI. The power loop includes the input capacitors, the two MOSFETs, the sense resistor, the inductor, and the output capacitors. The ground terminals of the input capacitors, the low side FET, the ADP3152, and the output capacitors should be connected together with short and wide traces. It is best to use an internal ground plane. 2. The PGND (power ground) pin of the ADP3152 must return to the grounded terminals of the input and output capacitors and to the source of the low side MOSFET with the shortest and widest traces possible. The AGND (analog ground) pin has to be connected to the ground terminals of the timing capacitor and the compensating capacitor, again with the shortest leads possible, and before it is connected to the PGND pin. 3. The positive terminal of the input capacitors must be connected to the drain of the high side MOSFET. The source terminal of this FET is connected to the drain of the low side FET, (whose source is connected to the ground plane direct) with the widest and shortest traces possible. To kill parasitic ringing at the input of the buck inductor due to parasitic capacitances and inductances, a small (L >3 mm) ferrite bead is recommended to be placed in the drain lead of the low side FET. Also, to minimize dissipation of the high side REV. 0 4. The positive terminal of the bypass capacitors of the +12 V supply must be connected to the VIN pin of the ADP3152 with the shortest leads possible. The negative terminals must be connected to the PGND pin of the ADP3152. 5. The sense pins of the ADP3152 must be connected to the sense resistor with as short traces as possible. Make sure that the two sense traces are routed together with minimum separation (<1 mm). The output side of the sense resistor should be connected to the VCC pin(s) of the CPU with as short and wide PCB traces as possible to reduce the VCC voltage drop. (Each square unit of 1 ounce Cu-trace has a resistance of ~0.53 m. At 14 A, each m of PCB trace resistance between current sense resistor output and VCC terminal(s) of the CPU will reduce the regulated output voltage by 14 mV. The filter capacitors to ground at the sense terminals of the IC should be as close as possible (<8 mm) to the ADP3152. The common ground of the optional filter capacitors should be connected to the AGND pin of the ADP3152 with the shortest traces possible (<10 mm). 6. The microprocessor load should be connected to the output terminals of the converter with the widest and shortest traces possible. Use overlapping traces in different layers to minimize interconnection inductance. -11- ADP3152 OUTLINE DIMENSIONS Dimensions shown in inches and (mm). C3260-8-4/98 16-Lead SOIC (R-16A/SO-16) 0.3937 (10.00) 0.3859 (9.80) 16 0.1574 (4.00) 0.1497 (3.80) 1 9 8 0.0500 SEATING (1.27) PLANE BSC 0.0688 (1.75) 0.0532 (1.35) 0.0192 (0.49) 0.0138 (0.35) 0.0099 (0.25) 0.0075 (0.19) 0.0196 (0.50) x 45 0.0099 (0.25) 8 0 0.0500 (1.27) 0.0160 (0.41) PRINTED IN U.S.A. PIN 1 0.0098 (0.25) 0.0040 (0.10) 0.2440 (6.20) 0.2284 (5.80) -12- REV. 0