JWS240P-48 - Lambda Semiconductors

NEMIC-LAMBDA

JWS 240P

SPECIFICATIONS

A182-01-01

ITEMS MODEL JWS240P-24 JWS240P-48

1 Nominal Output Voltage V24 48

2 Average Output Current A10 5

3 Peak Output Current (*1) A20 10

4 Average Output Power W240 240

5Peak Output Power (*1) W480 480

6 Efficiency (Typ) (*2) %80 80

7 Input Voltage Range (*3) -85 ~ 265VAC (47 ~ 63Hz)

8 Input Current (100/200VAC)(Typ) (*2) A3.2/1.6

9 Inrush Current(Typ) (*4) -20A at 100VAC, 40A at 200VAC

10 PFHC -Built to meet EN61000-3-2

11 Power Factor (100/200VAC)(Typ) (*2) - 0.99/0.95

12 Output Voltage Range V 21.6 ~ 28.8 43.2 ~ 52.8

13 Maximum Ripple & Noise 0 ~ +65°C mV 240 480

(*5) -10 ~ 0°C mV 360 720

14 Maximum Line Regulation (*6) mV 96 192

15 Maximum Load Regulation (*7) mV 192 384

16 Temperature Coefficient Less than 0.02%/°C

17 Over Current Protection (*8) A 20.4 ~ 10.2 ~

18 Over Voltage Protection (*9) V30.0 ~ 34.8 55.2 ~ 64.8

19 Hold-up Time (Typ) (*10) -20ms

20 Leakage Current (*11) -0.75mA MAX, 0.2mA(Typ) at 100VAC / 0.44mA(Typ) at 230VAC

21 Remote Sensing - Possible

22 Remote ON/OFF control - Possible

23 Monitoring Signal -PF (Open Collector Output)

24 Parallel Operation - ---

25 Series Operation -Possible

26 Operating Temperature (*12) --10 ~ +65°C ( -10 ~ +50°C:100%, +60°C:70%,+65°C:55% )

27 Operating Humidity - 30 ~ 90%RH (No dewdrop)

28 Storage Temperature --30 ~ +85°C

29 Storage Humidity - 10 ~ 95%RH (No dewdrop)

30 Cooling -Forced Air By Blower Fan

31 Withstand Voltage -Input - FG:2kVAC(20mA), Input - Output:3kVAC (20mA)

Output - FG:500VAC(100mA), Output-CNT:100VAC(100mA) for 1min.

32 Isolation Resistance -More than 100Mohm Output - FG... 500VDC

More than 10Mohm Output - CNT... 100VDC at 25°C and 70%Rh

33 Vibration -At no operating, 10-55Hz (Sweep for 1min)

2G Constant, X, Y, Z 1hour each.

34 Shock (In package) -Less than 20G

35 Safety (*13) -Built to meet UL1950, CSA950, EN60950,VDE0160.

Built to meet DENTORI.

36 Conducted Emission -Built to meet EN55011/EN55022-A, FCC-ClassA, VCCI-A.

37 Radiated Emission -Built to meet EN55011/EN55022-A, FCC-ClassA, VCCI-A.

38 Weight (Typ.) g 1900

39 Size (WxHxD) mm 120 x 92 x 190 ( Refer to Outline Drawing )

*Read instruction manual carefully, before using the power supply unit.

=NOTES=

*1. Operating time at peak output is less than 10sec.(Duty<=0.5)

*2. At 100/200VAC, Ta=25°C and average output power.

*3. For cases where conformance to various safety specifications (UL, CSA, EN) are required,

input voltage range will be 100-240VAC(50/60Hz).

*4. First in-rush current. Not applicable for the in-rush current to Noise Filter less than 0.2ms.

*5. Measure with EIAJ RC-9131A probe, Bandwidth of scope :100MHz.

*6. 85 - 265VAC , constant load.

*7. No load - Average load, constant input voltage.

*8. Constant current limit with automatic recovery.

Peak current and shorted conditions more than 10 seconds, which could be result of shut down the output voltage.

*9. OVP circuit will shut down output, manual reset (Line recycle).

*10. At 100/200VAC nominal output voltage and average output current.

*11. Measured by the each measuring method of UL, CSA, EN and DENTORI(at 60Hz).

*12. Ratings - Derating at standard mounting.

- Load (%) is percent of average output power or averge output current, whichever is greater.

- As for other mountings, refer to derating curve (A182-01-02_).

*13. As for DENTORI, built to meet at 100VAC.

A1820101_Pdf.xls