DRAWING MADE IN THIRD ANGLE PROJECTION S THIS DRAWING IS UNPUBLISHED. RELEASED FOR PUBLICATION ,19 . Loc DIST REVISIONS COPYRIGHT 19 BY AMP INCORPORATED. ALL INTERNATIONAL RIGHTS RESERVED. DF DO P E ZONE LTR DESCRIPTION DATE APPD C |REV PER OH14-0225-04 CT 3-04 LO 1. THIS CONNECTOR ASSEMBLY IS SUPPLIED WITH METAL CONTACT RETENTION D CLIPS INSTALLED IN THE INSERT ASSEMBLY. D 2. THIS CONNECTOR ASSEMBLY MEETS THE REQUIREMENTS OF LORAL SPEC 010772 AND MATES WITH ANY RECEPTACLE CONNECTOR WITH SAME INSERT ARRANGEMENT . 2 MARK WITH .047 [1.19]-.062 [1.57] HIGH CHARACTERS. FAR SIDE REFERS TO THE WIDE SIDE OF THE KEYSTONE. NEAR SIDE REFERS TO THE NARROW SIDE OF THE KEYSTONE. IF THE REAR SHELL IS TOO SMALL FOR THE ENTIRE CUSTOMER PART NUMBER, MARKING SHALL BE LOCATED AS FOLLOWS: A. ~BO10772 ON FRONT SHELL, FAR SIDE. } B. CUSTOMER BASE NUMBER ON FRONT SHELL, NEAR SIDE. C. AMP AND DATE CODE ON FRONT SHELL, NEAR SIDE. D. AMP PART NUMBER ON REAR SHELL, NEAR SIDE. /\ DIMENSIONS ARE .155 [3.94] MINIMUM FULL PIN DIAMETER EXTENSION (SIZES 3 THRU &) AND .164 [4.17] MINIMUM FULL PIN DIAMETER EXTENTION (SIZES 1 AND 2). 5S. MAXIMUM WIRE INSULATION TO BE USED WITH THIS CONNECTOR ASSEMBLY IS .072 [1.83] DIAMETER. 6. FOR CONTACT CRIMPING INSTRUCTION SHEET REFER TO AMP [5S 7516. FOR CONTACT INSTALLATION AND REMOVAL INSTRUCTION SHEET REFER TO AMP IS 7508. 7. DIMENSIONS AND TOLERANCES PER ANSI Y14.5M-1982. 8. THIS DRAWING SHALL BE INTERPRETED IN ACCORDANCE WITH APPLICABLE STANDARDS LISTED IN MIL-STD-100. .544 .13.82,| 2.188 -55.58 620 -15.75 441 11,20-| 2.411 -61.24.| 2.084 -52.93.| 2.650 -67.31 .524 [43.314 2.168 Les o7/ .590 [14 gg 437 Lio gs! 2.401 [50.99 2.074 [S35 68! 2.620 Lo6. ss! MSTB270' 20 > BOTO??20031 1~4488155 1-448815-5 049 1.24 2,282 57.96 236 5.99 .436 .11.07 2.505 _-63.63.] 2.187 -55.55.| 2.744 .69.70 .029 Lo 741 2,262 Le? 4s! 224 LS 69! .416 Lio S77! 2,495 L653. 37! 2.177 Les. 30! 2.714 Leg. 94/ MS18276~1 3 4 BO1O?72-0029 1~448815~4 1~448815~4 1.635 .41.53 1.857 -47.17-5| 1.539 -39.09.| 2.103 .-53.42 .432 (10-975 1.615 Lay o>! .509 (12-935 334 ( 8.48 5 1.847 Lag. a1 1,529 (33. ga! 2.073 [S35 gs! MSTB2751 29 3 BO1TO??2-002 1~4488153 1~448815-3 .412 +10.46-| 1.093 27.76 .479 112.17 324 8.23 -] 1.317 -33.45 999 .25.37.,| 1.556 -39.52 B .040 r 1-02 4 1.073 L735] 241 , 8-125 . 432 (10.975 1,307 33.30! .989 Iss 72! 1.526 33.761 MS18274" 1s e BO1O?72-0025 '~448815-2 '~448815~2 B .020 0.51 .769 19.53 229 5.82 .412 410.46 .989 25.12 671 17.04,| 1.228 -31.19 49 Lig oo! G79 [Sn a7] _ Li 6g 5g] , 198 [30 43! MS18273-1 g 1 BO10772-0023 1-448815-1 1-448815-1 .544 .13.82,| 2.188 ,-55.58 620 ,-15.75 441 11,20-| 2.411 -61.24.| 2.084 -52.93.| 2.650 -67.31 .524 [43.311 2.168 LSS 07! 590 [149g 437 Lio gs! 2.401 L 50.99! 2.074 Lo3 ge! 2.620 Lo6. ss! MS18277| 30 S AOTO??72-0003 1~4488150 1~448815-0 O43 1.24 2.282 .57.96 236 5.99 .436 -11.07 2.505 -63.63.| 2.187 -S55.55.| 2.744 -69.70 .029 Lo 741 2. 262 Lo7 4s! 224 L 5 gg J _416 Lio sz] 2,495 [53.374 2.177 Les. 30! 2.714 Le3.94/ MST182761 3 4 AOTO?72-000% 448815-3 448815-3 1.635 .41.53 1.857 .47.17,| 1.539 ,-39.09.| 2.103 53.42 . 432 (10-874 1.615 bay oD! 50g (12-33) 334 (8.484 1.847 Las. ai! 1.529 L338. ga! 2.073 LSS gs! MS16275~| 25 3 AQT O??72-0005 448815-8 448815-8 .412 +10.46-| 1.093 27.76 .479 112.17 324 8.23 -] 1.317 -33.45 6999 .25.37.| 1.556 ,-39.52 .040 (1-02 5 1.073 L572 351 241 , +125 .432 (10.975 1,307 33.30! mcisis L512! 1.526 33.761 MST82741 1s e AO10?772-0003 448815~? 448815~? .020 0.51 .769 -19.53 229 5.82 .412 110.46 6989 .25.12 671 17.04,| 1.228 -31.19 . 749 Lig o5l .979 [54 874 .661 Lig 7g 1.198 L350. 431 MS182731 s | AOTO??2-0001 448815-6 448815-6 .544 .13.82,| 2.188 ,-55.58 .620 -15.75 441 11,20-| 2.411 -61.24.| 2.084 -52.93.| 2.650 -67.31 .524 [43.314 2.168 Les o7/ .590 [14.99 437 Lio gs! 2.401 L50.99/ 2.074 Lo5 ge! 2.620 Los. ss/ MS18277| 30 > BOlo??720003 44881 55 448815-5 O49 1.24 2.282 .57.96 236 5.99 .436 -11.07 2.505 ,-63.63.| 2.187 -55.55.| 2.744 -69.70 .029 Lo 741 2.262 Lo7 4s! 224 LS gg J .416 Lio S21 2,495 [53.371 2.177 Les. 30! 2.714 Ls3.94/ MS18276~1 3 4 BOTO?72-000% 44881 5-4 4488 15-4 1.635 .41.53 1.857 .47.17,| 1.539 -39.09.| 2.103 .53.42 . 432 (10-975 1.615 Lyi oD .509 (12-93) 334 ; 8.485 1.847 Lusg.ai4 1,529 33 gq! 2.073 [S551 MST8275~1 29 3 BO1O?772-0005 448815~-3 448815~-3 .412 +10.46-| 1.093 27.76 .479 412.17 324 8.23-1 1.317 -33.45 .999 ,25.37.| 1.556 -39.52 .040 (1.024 1.073 L572 351 DAI (6.124 .432 (10-874 1.307 [33301 .989 55.12! 1.526 33.761 MSTB2741 1s BO1TO?72-0003 4488 15-2 4488 15-2 .020 0.51 .769 -19.53 229 5.82 .412 110.46 .989 .25.12 671 17,.04,| 1.228 -31.19 .749 Lig op .979 [54871 661 Lig 79 1.198 L350. 431 MST82731 d | BOTo??20001 448815~| 448815-1 INSERT CUSTOMER P/N AMP P/N L J H e F E D C B A NO OF} SHELL VN J PART wumaerZ\ ARRANGEMENT | POS SIZE ON CONNECTOR ON CONNECTOR DO NOT SCALE PRINT. DR a ORIEE UNLESS SPECIFIED AMP INCORPORATED DIMENSIONS IN INCHES [Emm] CHK 317293 MAINA L ooenistung, Po. 17108 2 PLC DEC + - , 3 PLC DEC + - APPD 2-17-93 NAME ANGLES + 1 F.KINSEY AMPLIMITE NONMAGNETIC PLUG ASSY MATERIAL _-17~ see ey WITH SIZE 20 CRIMP TYPE SEE CALLOUTS PRODUCT SPEC PIN CONTACTS, SERIES 109, MIL-C-24308 SHELL SIZES 1 THRU 5 FINISH APPLICATION SPEC SIZ FSCM NO DRAWING NO SEE CALLOUTS 7 Wy | O07 79 AAS] 5 WEIGHT | SCALE 4. ] - SHEET 1 of D AMP 1756-3 REV 3-87 WY L- ! CUSTOMER DRAWING 30-MAR-04 07:56:33 us016412 /home/us016412/docmod pe DRAWING MADE IN THIRD ANGLE PROJECTION S THIS DRAWING IS UNPUBLISHED. RELEASED FOR PUBLICATION ,19 . Loc DIST REVISIONS COPYRIGHT 19 BY AMP INCORPORATED. ALL INTERNATIONAL RIGHTS RESERVED. DF DO P FE ZONE LTR DESCRIPTION DATE APPD C |SEE SHEET #1 _ _ D D .106 [2.69] R402 f2.59) 'YF RAISED CAVITY B > INDENTIFICATION NUMBERS R O32 [2.34] TYP gles [3.18] > PLC .0O62 [1.57] .115 [2,92] 10 TYP~ i I 7 tH _ > | O - \X\ 0 O \X\ Y Kf a, | | \ O TYP het H a C a MATING FACE ja A an C View Z-Z C AX MARK AMP, AMP PART NO AND DATE CODE, FAR SIDE SHELL, FRONT MATL: BRASS ALLOY PER ASTM B 36 FINISH: GOLD PLATED IN ACCORDANCE WITH MIL-G-45204, TYPE II, GRADE C, CLASS 1 | ; OVER COPPER IN ACCORDANCE WITH MIL-C-14550. x i 220 if S93] . Y x N /| a | {Max r pS SS A .375 MAX (9.53) .070 [1.78] TYP | \ .0O40 [1.02] SHELL, REAR MATL: BRASS ALLOY PER ASTM 6 36 / FINISH: GOLD PLATED IN ACCORDANCE WITH B d MIL-G-45204, TYPE II, GRADE C, CLASS 1 B .125 REF OVER COPPER IN ACCORDANCE WITH MIL-C-14550. [3.18] GROMMET, REAR MATL: SILICONE RUBBER INSERT ASSEMBLY MARK CUSTOMER PART NO, PER LAW 27_R-765 MATL: DIALLYL PHTHALATE CONTACT FAR SIDE. , PER MIL-M-14, TYPE SDG-F CLASS 3a, GRADE SO AMP P/N 205089-4 COLOR: RED FOR 448815-1 THRU -10 ONLY DO NOT SCALE PRINT. DR a ORIEE UNLESS SPECIFIED DIMENSIONS IN INCHES [Emm] CHR 3219293 AMP erciebuce, Pa. 19108 A TOLERANCES ON : F_KINSEY A 2 PLC DEC + - 3 PLC DEC + - APPD 32-17-93 NAME ANGLES + 1 F . KINSEY AMPLIMITE NONMAGNETIC PLUG ASSY MATERTAL APPD 2-17-83 WITH SIZE 20 CRIMP TYPE SEE CALLOUTS PRODUCT SPEC PIN CONTACTS, SERIES 109, MIL-C-24308 SHELL SIZES 1 THRU 5 FINISH APPLICATION SPEC SIZ FSCM NO DRAWING NO SEE CALLOUTS - Wy | O07 79 AABB15 WEIGHT _ SCALE 4. ] - SHEET >of D AMP 1756-3 REV 3-87 WY L- ! CUSTOMER DRAWING 30-MAR-04 08:07:54 us016412 /home/us016412/docmod pe