19-3321; Rev 0; 10/05 Low-Cost CCFL Backlight Controller The MAX8722A integrated backlight controller is optimized to drive cold-cathode fluorescent lamps (CCFLs) using a full-bridge resonant inverter architecture. Resonant operation maximizes striking capability and provides near-sinusoidal waveforms over the entire input range to improve CCFL lifetime. The controller operates over a wide input voltage range (4.6V to 28V) with high power to light efficiency. The device also includes safety features that effectively protect against many single-point fault conditions including lamp-out and short-circuit faults. The MAX8722A achieves 10:1 dimming range by "chopping" the lamp current on and off using a digital pulsewidth modulation (DPWM) method. The DPWM frequency can be accurately adjusted with a resistor or synchronized to an external signal. The brightness is controlled by an analog voltage on the CNTL pin. The device directly drives the four external n-channel power MOSFETs of the full-bridge inverter. An internal 5.3V linear regulator powers the MOSFET drivers, the DPWM oscillator, and most of the internal circuitry. The MAX8722A is available in a low-cost, 24-pin QSOP package and operates over a -40C to +85C temperature range. Features Synchronized to Resonant Frequency Longer Lamp Life Guaranteed Striking Capability High Power to Light Efficiency Wide Input Voltage Range (4.6V to 28V) Input-Voltage Feed-Forward for Excellent Line Rejection Accurate Dimming Control with Analog Interface 10:1 Dimming Range Adjustable Accurate DPWM Frequency with Sync Function Adjustable Lamp Current Rise and Fall Time Secondary Voltage Limit Reduces Transformer Stress Lamp-Out Protection with Adjustable Timeout Secondary Overcurrent Protection with Adjustable Timeout Low-Cost 24-Pin QSOP Package Ordering Information Applications PART TEMP RANGE PIN-PACKAGE PKG CODE MAX8722AEEG -40C to +85C 24 QSOP E24-1 Notebook Computer Displays LCD Monitors LCD TVs Minimal Operating Circuit Pin Configuration VIN VCC VDD BATT TOP VIEW GND BATT 1 24 GND SHDN 2 23 VCC ILIM 3 22 VDD TFLT 4 CNTL 5 VCC VCC BST1 GH1 ILIM 21 PGND MAX8722A BST2 MAX8722A LX1 20 GL2 DPWM 6 19 GL1 SYNC 7 18 GH1 FREQ 8 17 LX1 COMP 9 16 BST1 LX2 FREQ GL1 PGND SHDN CNTL SYNC IFB 10 15 BST2 VFB 11 14 LX2 ISEC 12 13 GH2 GL2 GH2 VFB DPWM ISEC COMP IFB TFLT QSOP ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim's website at www.maxim-ic.com. 1 MAX8722A General Description MAX8722A Low-Cost CCFL Backlight Controller ABSOLUTE MAXIMUM RATINGS SHDN to GND...........................................................-0.3V to +6V PGND to GND .......................................................-0.3V to +0.3V Continuous Power Dissipation (TA = +70C) 24-Pin QSOP (derate 9.5mW/C above +70C)........761.9mW Operating Temperature Range ...........................-40C to +85C Junction Temperature ......................................................+150C Storage Temperature Range .............................-65C to +150C Lead Temperature (soldering, 10s) .................................+300C BATT to GND..........................................................-0.3V to +30V BST1, BST2 to GND ...............................................-0.3V to +36V BST1 to LX1, BST2 to LX2 ........................................-0.3V to +6V CNTL, FREQ, SYNC, VCC, VDD to GND ...................-0.3V to +6V COMP, DPWM, ILIM, TFLT to GND ............-0.3V to (VCC + 0.3V) GH1 to LX1 ..............................................-0.3V to (VBST1 + 0.3V) GH2 to LX2 ..............................................-0.3V to (VBST2 + 0.3V) GL1, GL2 to GND .......................................-0.3V to (VDD + 0.3V) IFB, ISEC, VFB to GND................................................-3V to +6V Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (Circuit of Figure 1. VBATT = 12V, VCC = VDD, VSHDN = 5.3V, TA = 0C to +85C. Typical values are at TA = +25C, unless otherwise noted.) PARAMETER BATT Input Voltage Range CONDITIONS MIN TYP MAX VCC = VDD = VBATT 4.6 5.5 VCC = VDD = open 5.5 28.0 VBATT = 28V BATT Quiescent Current VSHDN = VCC, VIFB = 1V BATT Quiescent Current, Shutdown SHDN = GND VCC Output Voltage, Normal Operation VSHDN = 5.5V, 6V < VBATT < 28V, 0 < ILOAD < 10mA VCC Output Voltage, Shutdown SHDN = GND, no load VCC Undervoltage-Lockout Threshold VCC rising (leaving lockout) 1 VBATT = VCC = 5V VCC falling (entering lockout) 2 2 UNITS V mA 6 20 A 5.25 5.40 5.55 V 3.5 4.6 5.5 V 4.58 4.0 VCC Undervoltage-Lockout Hysteresis 200 V mV GH1, GH2, GL1, GL2 OnResistance, High ITEST = 10mA, VCC = VDD = 5.3V 20 37 GH1, GH2, GL1, GL2 OnResistance, Low ITEST = 10mA, VCC = VDD = 5.3V 10 20 GH1, GH2, GL1, GL2 Maximum Output Current 0.3 BST1, BST2 Leakage Current VBST_ = 12V, VLX_ = 7V Resonant Frequency Range Guaranteed by design 30 A 5 A 80 kHz Minimum Off-Time 340 470 600 ns Maximum Off-Time 24 33 43 s ILIM = VCC 180 200 220 mV VILIM = 0.5V 80 100 120 VILIM = 2.0V 370 400 430 Current-Limit Threshold LX1 to PGND, LX2 to PGND (Fixed) Current-Limit Threshold LX1 to PGND, LX2 to PGND (Adjustable) 2 mV _______________________________________________________________________________________ Low-Cost CCFL Backlight Controller (Circuit of Figure 1. VBATT = 12V, VCC = VDD, VSHDN = 5.3V, TA = 0C to +85C. Typical values are at TA = +25C, unless otherwise noted.) PARAMETER CONDITIONS Zero-Current Crossing Threshold LX1 to GND, LX2 to GND Current-Limit Leading Edge Blanking IFB Input Voltage Range MIN TYP MAX UNITS 1 6 12 mV 240 350 460 ns +2 V 790 810 mV -2 IFB Regulation Point 770 IFB Input Bias Current 0 < VIFB < 2V -2 -2V < VIFB < 0 -150 IFB Lamp-Out Threshold IFB to COMP Transconductance 0.5V < VCOMP < 4V COMP Output Impedance +2 A 560 600 640 mV 60 100 160 S 7 10 18 M COMP Discharge Current During Overvoltage or Overcurrent Fault VIFB = 800mV, VISEC = 2V 1200 A COMP Discharge Current During DPWM Off-Time CNTL = GND, VCOMP = 2V 100 A DPWM Rising to Falling Ratio VIFB = 0 2.5 -- ISEC Overcurrent Threshold 1.28 V ISEC Input Bias Current 0 < VISEC < 2V 1.15 -0.3 +0.3 A VFB Input Bias Current -4V < VVFB < +4V -25 +25 A 2.4 V 214 Hz 0.8 V VFB Overvoltage Threshold 2.2 RFREQ = 100k DPWM Chopping Frequency RFREQ = 169k SYNC = VCC, RFREQ = 169k DPWM Input High Voltage SYNC = VCC, RFREQ = 169k DPWM Input Hysteresis SYNC = VCC, RFREQ = 169k DPWM Input Bias Current SYNC = VCC, RFREQ = 169k DPWM Output Low Resistance DPWM Output High Resistance 2.3 343 204 RFREQ = 340k DPWM Input Low Voltage 1.21 209 106 2.1 V 100 -0.3 A SYNC = GND, FREQ = VCC 2.4 k SYNC = VCC, FREQ = VCC 2.4 k 0.8 V SYNC Input Low Voltage SYNC Input High Voltage 2.1 SYNC Input Hysteresis SYNC Input Bias Current mV +0.3 V 100 VSYNC = 2V SYNC Input Frequency Range mV -0.3 +0.3 A 10 50 kHz CNTL Minimum Duty-Cycle Threshold 0.20 0.23 0.26 V CNTL Maximum Duty-Cycle Threshold 1.9 2.0 2.1 V +0.1 A CNTL Input Current 0 < VCNTL < VCC DPWM ADC Resolution Guaranteed monotonic -0.1 5 Bits _______________________________________________________________________________________ 3 MAX8722A ELECTRICAL CHARACTERISTICS (continued) MAX8722A Low-Cost CCFL Backlight Controller ELECTRICAL CHARACTERISTICS (continued) (Circuit of Figure 1. VBATT = 12V, VCC = VDD, VSHDN = 5.3V, TA = 0C to +85C. Typical values are at TA = +25C, unless otherwise noted.) PARAMETER CONDITIONS MIN TYP MAX UNITS 0.8 V SHDN Input Low Voltage SHDN Input High Voltage 2.1 SHDN Input Bias Current -1 FREQ Dual ModeTM Input High Level FREQ = VCC VISEC < 1.25V and VIFB < 600mV; VFLT = 2V TFLT Charge Current +1 VCC 0.35 FREQ Input Regulation Level FREQ Input Bias Current V 0.95 V VCC / 2 V 230 A 1.00 VISEC < 1.25V and VIFB > 600mV; VFLT = 2V -1 VISEC > 1.25V and VIFB < 600mV; VFLT = 2V 116 TFLT Trip Threshold 3.95 A 1.05 A 4.10 4.20 V MAX UNITS Dual Mode is a trademark of Maxim Integrated Products, Inc. ELECTRICAL CHARACTERISTICS (Circuit of Figure 1. VBATT = 12V, VCC = VDD, V SHDN = 5.3V, TA = -40C to +85C, unless otherwise noted.) (Note 1) PARAMETER BATT Input Voltage Range CONDITIONS MIN TYP VCC = VDD = VBATT 4.6 5.5 VCC = VDD = open 5.5 28.0 VBATT = 28V 2 VBATT = VCC = 5V 2 BATT Quiescent Current VSHDN = VCC, VIFB = 1V BATT Quiescent Current, Shutdown SHDN = GND VCC Output Voltage, Normal Operation VSHDN = 5.5V, 6V < VBATT < 28V 0 < ILOAD < 20mA 5.25 VCC Output Voltage, Shutdown SHDN = GND, no load 3.5 VCC Undervoltage-Lockout Threshold VCC rising (leaving lockout) VCC falling (entering lockout) V mA 20 A 5.55 V 5.5 V 4.58 4.0 V GH1, GH2, GL1, GL2 OnResistance, High ITEST =10mA, VCC = VDD = 5.3V 37 GH1, GH2, GL1, GL2 OnResistance, Low ITEST =10mA, VCC = VDD = 5.3V 20 BST1, BST2 Leakage Current VBST_ = 12V, VLX_ = 7V 5 A Resonant Frequency Range Guaranteed by design 30 80 kHz Minimum Off-Time 340 600 ns Maximum Off-Time 24 43 s 180 220 mV Current-Limit Threshold LX1 - PGND, LX2 - PGND (Fixed) 4 ILIM = VCC _______________________________________________________________________________________ Low-Cost CCFL Backlight Controller (Circuit of Figure 1. VBATT = 12V, VCC = VDD, V SHDN = 5.3V, TA = -40C to +85C, unless otherwise noted.) (Note 1) PARAMETER Current-Limit Threshold LX1 - PGND, LX2 - PGND (Adjustable) CONDITIONS MIN MAX UNITS VILIM = 0.5V 80 120 VILIM = 2.0V 370 430 1 12 mV 240 460 ns -2 +2 V mV mV Zero-Current Crossing Threshold LX1 - GND, LX2 - GND Current-Limit Leading Edge Blanking IFB Input Voltage Range IFB Regulation Point IFB Input Bias Current TYP 770 810 0 < VIFB < 2V -2 +2 -2V < VIFB < 0 -150 IFB Lamp-Out Threshold A 560 640 60 160 S 7 18 M ISEC Overcurrent Threshold 1.15 1.28 V VFB Overvoltage Threshold 2.2 2.4 V 200 218 Hz 0.8 V IFB to COMP Transconductance 0.5V < VCOMP < 4V COMP Output Impedance mV DPWM Chopping Frequency RFREQ = 169k DPWM Input Low Voltage SYNC = VCC, RFREQ = 169k DPWM Input High Voltage SYNC = VCC, RFREQ = 169k DPWM Output Low Resistance SYNC = GND, FREQ = VCC 2.4 k DPWM Output High Resistance SYNC = VCC, FREQ = VCC 2.4 k 0.8 V -0.3 +0.3 A 10 50 kHz CNTL Minimum Duty-Cycle Threshold 0.20 0.26 V CNTL Maximum Duty-Cycle Threshold 1.9 2.1 V 0.8 V 2.1 SYNC Input Low Voltage SYNC Input High Voltage SYNC Input Bias Current V 2.1 VSYNC = 2V SYNC Input Frequency Range SHDN Input Low Voltage SHDN Input High Voltage V 2.1 V FREQ Dual-Mode Input High Level VCC 0.35 V TFLT Trip Threshold 3.95 4.20 V Note 1: Specifications to -40C are guaranteed by design based on final characterization results. _______________________________________________________________________________________ 5 MAX8722A ELECTRICAL CHARACTERISTICS (continued) MAX8722A Low-Cost CCFL Backlight Controller Typical Operating Characteristics (Circuit of Figure 1. VBATT = 12V, VCC = VDD, VSHDN = 5.3V, TA = +25C, unless otherwise noted.) LOW INPUT-VOLTAGE OPERATION (VBATT = 8V) HIGH INPUT-VOLTAGE OPERATION (VBATT = 20V) MAX8722 toc01 LINE TRANSIENT RESPONSE MAX8722 toc02 MAX8722 toc03 0V A 0V A 0V A 0V B 0V B 0V B 0V D D C: VLX1, 10V/div D: VLX2, 10V/div A: VIFB, 2V/div B: VVFB, 2V/div 20s/div C: VLX1, 10V/div D: VLX2, 10V/div MINIMUM BRIGHTNESS DPWM OPERATION (VCNTL = 0) MAX8722 toc05 MAX8722 toc04 MAX8722 toc06 0V A 0V A 0V A 0V B 0V B 0V B C C C 0V 20V 0V 0V D 10V D D 0V 0V C: VLX1, 10V/div D: VBATT, 10V/div C: VLX1, 10V/div D: VBATT, 10V/div A: VVFB, 2V/div B: VIFB, 2V/div MINIMUM BRIGHTNESS STARTUP WAVEFORM (VCNTL = 0) LINE TRANSIENT RESPONSE 6 0V 10s/div 20s/div 10V D 0V 10s/div A: VVFB, 2V/div B: VIFB, 2V/div 0V 20V 0V 0V A: VIFB, 2V/div B: VVFB, 2V/div C C C 2ms/div A: VIFB, 2V/div B: VVFB, 2V/div C: VCOMP, 1V/div D: VSHDN, 5V/div 0V 2ms/div A: VIFB, 2V/div B: VVFB, 2V/div _______________________________________________________________________________________ C: VCOMP, 1V/div D: VDPWM, 5V/div Low-Cost CCFL Backlight Controller 50% BRIGHTNESS DIGITAL PWM OPERATION (VCNTL = 1V) DPWM SOFT-START DPWM SOFT-STOP MAX8722 toc08 MAX8722 toc07 MAX8722 toc09 0V A 0V A 0V A 0V B 0V B 0V B C C C 0V 0V D D D 0V 0V 0V 40s/div 2ms/div A: VIFB, 2V/div B: VVFB, 2V/div C: VCOMP, 1V/div D: VDPWM, 5V/div 40s/div C: VCOMP, 1V/div D: VDPWM, 5V/div SECONDARY OVERCURRENT PROTECTION AND TIMEOUT SWITCHING FREQUENCY vs. INPUT VOLTAGE MAX8722 toc11 MAX8722 toc10 60 A A 0V 0V B 0V B MAX8722 toc12 LAMP-OUT VOLTAGE LIMITING AND TIMEOUT C: VCOMP, 1V/div D: VDPWM, 5V/div A: VIFB, 2V/div B: VVFB, 2V/div SWITCHING FREQUENCY (kHz) A: VIFB, 2V/div B: VVFB, 2V/div 0V 57 54 51 48 C 0V 0V 4ms/div 200ms/div A: VIFB, 2V/div B: VVFB, 2V/div C: VTFLT, 5V/div A: VISEC, 500mV/div B: VTFLT, 2V/div 45 8 12 16 20 24 INPUT VOLTAGE (V) _______________________________________________________________________________________ 7 MAX8722A Typical Operating Characteristics (continued) (Circuit of Figure 1. VBATT = 12V, VCC = VDD, VSHDN = 5.3V, TA = +25C, unless otherwise noted.) Typical Operating Characteristics (continued) (Circuit of Figure 1. VBATT = 12V, VCC = VDD, VSHDN = 5.3V, TA = +25C, unless otherwise noted.) 250 200 6.05 209 206 203 150 100 150 200 250 300 10 5.90 NOMINAL CURRENT SET POINT 13 16 19 22 12 8 25 16 NORMALIZED BRIGHTNESS vs. CNTL VOLTAGE VCC LINE REGULATION 0.2 0 VCC ACCURACY (%) 80 60 40 MAX8722 toc17 0.4 MAX8722 toc16 100 20 INPUT VOLTAGE (V) INPUT VOLTAGE (V) RFREQ () NORMALIZED BRIGHTNESS (%) 5.95 5.80 7 350 6.00 5.85 200 100 MAX8722 toc15 212 RMS LAMP CURRENT (mA) 300 6.10 MAX8722 toc14 350 215 DIGITAL PWM FREQUENCY (Hz) MAX8722 toc13 400 RMS LAMP CURRENT vs. INPUT VOLTAGE DPWM FREQUENCY vs. INPUT VOLTAGE DPWM FREQUENCY vs. RFREQ DIGITAL PWM FREQUENCY (Hz) -0.2 -0.4 -0.6 20 -0.8 0 -1.0 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 4 8 CNTL VOLTAGE (V) 16 20 24 VCC ACCURACY vs. TEMPERATURE VCC LOAD REGULATION 0.03 VCC ACCURACY (%) -0.2 -0.3 -0.4 MAX8722 toc19 0.04 MAX8722 toc18 -0.1 0.02 0.01 0 -0.01 -0.02 -0.5 0 2 4 6 LOAD CURRENT (mA) 8 12 INPUT VOLTAGE (V) 0 VCC ACCURACY (%) MAX8722A Low-Cost CCFL Backlight Controller 8 10 -40 -20 0 20 40 60 80 TEMPERATURE (C) _______________________________________________________________________________________ 100 24 Low-Cost CCFL Backlight Controller PIN NAME 1 BATT Supply Input. BATT is the input to the internal 5.4V linear regulator that powers the device. Bypass BATT to GND with a 0.1F ceramic capacitor. 2 SHDN Shutdown Control Input. The device shuts down when SHDN is pulled to GND. 3 ILIM Primary Current-Limit Adjustment Input. Connect a resistive voltage-divider between VCC and GND to set the primary current limit. The current-limit threshold is 1/5 of the voltage at ILIM. Connect it to VCC with a pullup resistor to select the default current-limit threshold of 0.2V. 4 TFLT Fault Timer Adjustment Pin. Connect a capacitor from TFLT to GND to set the timeout periods for openlamp and secondary overcurrent faults. 5 CNTL Brightness Control Input. Varying VCNTL between 0 and 2V varies the DPWM duty cycle (brightness) between 10% (minimum) and 100% (maximum). The brightness remains at maximum for VCNTL greater than 2V. 6 DPWM Dual-Function DPWM Signal Pin. The DPWM pin can be used either as the DPWM signal output or as a low-frequency sync input. See the DPWM Dimming Control and DPWM Frequency Setting sections. 7 SYNC DPWM High-Frequency Sync Input. The DPWM chopping frequency can be synchronized to an external high-frequency signal by connecting FREQ to VCC and SYNC to the external signal source. The DPWM chopping frequency is 1/128 of the frequency of the external signal. 8 FREQ DPWM Frequency Dual-Mode Adjustment Pin. Connect a resistor from FREQ to GND to set the DPWM frequency. Connect FREQ to VCC to set DPWM frequency using SYNC. fDPWM = 209Hz x 169k / RFREQ 9 COMP Transconductance Error-Amplifier Output. A compensation capacitor connected between COMP and GND sets the rise and fall time of the lamp current in DPWM operation. 10 IFB Lamp-Current Feedback Input. The average voltage on IFB is regulated to 0.8V by controlling the on-time of high-side switches. If VIFB falls below 0.6V for a period longer than the timeout period set by TFLT, the MAX8722A activates the fault latch. VFB Transformer Secondary Voltage Feedback Input. A capacitive voltage-divider between the high-voltage terminal of the CCFL tube and GND sets the maximum average lamp voltage during lamp strike and openlamp conditions. When the average voltage on VFB exceeds the internal overvoltage threshold, the controller turns on an internal current sink discharging the COMP capacitor. 12 ISEC Transformer Secondary Current Feedback Input. A current-sense resistor connected between the lowvoltage end of the transformer secondary and ground sets the maximum secondary current during faults. When the average voltage on ISEC exceeds the internal overcurrent threshold, the controller turns on an internal current sink discharging the COMP capacitor. 13 GH2 High-Side MOSFET NH2 Gate-Driver Output 14 LX2 GH2 Gate-Driver Return. LX2 is the input to the current-limit and zero-crossing comparators. The device senses the voltage across the low-side MOSFET NL2 to detect primary current zero-crossing and primary overcurrent. 15 BST2 GH2 Gate-Driver Supply Input. Connect a 0.1F capacitor from LX2 to BST2 and a diode from VDD to BST2 to form a bootstrap circuit. 16 BST1 GH1 Gate-Driver Supply Input. Connect a 0.1F capacitor from LX1 to BST1 and a diode from VDD to BST1 to form a bootstrap circuit. 17 LX1 11 FUNCTION GH1 Gate-Driver Return. LX1 is the input to the current-limit and zero-crossing comparators. The device senses the voltage across the low-side MOSFET NL1 to detect primary current zero-crossing and primary overcurrent. _______________________________________________________________________________________ 9 MAX8722A Pin Description Low-Cost CCFL Backlight Controller MAX8722A Pin Description (continued) PIN NAME 18 GH1 High-Side MOSFET NH1 Gate-Driver Output 19 GL1 Low-Side MOSFET NL1 Gate-Driver Output 20 GL2 Low-Side MOSFET NL2 Gate-Driver Output 21 PGND 22 VDD Low-Side Gate-Driver Supply Input. Connect VDD to the output of the internal linear regulator (VCC). Bypass VDD with a 0.1F capacitor to PGND. 23 VCC 5.3V/10mA Internal Linear-Regulator Output. VCC is the supply voltage for the device. Bypass VCC with a 1F ceramic capacitor to GND. 24 GND Analog Ground. The ground return for VCC, REF, and other analog circuitry. Connect GND to PGND under the IC at the IC's backside exposed metal pad. VIN FUNCTION Power Ground. PGND is the return for the GL1 and GL2 gate drivers. F1 C1 4.7F 25V VCC 2A GND VDD C8 0.1F GND MAX8722A D1 VCC C9 0.47F C7 0.47F BATT VCC BST2 BST1 R4 100k GH1 ILIM R5 200k NH1 NH2 C2 1F C6 0.1F LX2 CCFL T1 LX1 C5 0.1F FREQ R6 169k 1% NL1 GL1 NL2 C3 18pF 3kV PGND ON/OFF SHDN BRIGHTNESS GL2 GH2 CNTL SYNC VFB ISEC SYNC IFB COMP DPWM DPWM TFLT C11 0.22F C10 0.01F R3 40.2 1% C4 15nF Figure 1. Typical Operating Circuit of the MAX8722A 10 ______________________________________________________________________________________ R1 150 1% Low-Cost CCFL Backlight Controller MAX8722A BIAS SUPPLY EN LINEAR REGULATOR BATT SHDN GND MAX8722A FLT BST1 VCC OVERVOLTAGE COMPARATOR RAMP UVLO 4.2V 2.3V GH1 UVLO COMPARATOR LX1 BST2 OVERCURRENT VFB COMP PWM COMPARATOR 1200A 100A GATE-DRIVER CONTROL STATE MACHINE PWM CONTROL LOGIC GH2 LX2 VDD GL1 PGND IFB PRIMARY OVERCURRENT AND ZEROCROSSING F.W. RECT 800mV FREQ DPWM GL2 ERROR AMPLIFIER DPWM OSCILLATOR AND DIMMING CONTROL LOGIC SYNC MUX ILIM CNTL OPEN-LAMP COMPARATOR 600mV ISEC H.W. RECT OVERCURRENT FAULT DELAY BLOCK FAULT LATCH S SHDN 1.25V TFLT SECONDARY OVERCURRENT COMPARATOR UVLO Q RESET FLT R Figure 2. MAX8722A Functional Diagram ______________________________________________________________________________________ 11 MAX8722A Low-Cost CCFL Backlight Controller Typical Operating Circuit The typical operating circuit of the MAX8722A (Figure 1) is a complete CCFL backlight inverter for TFT-LCD panels. The input voltage range of the circuit is from 8V to 24V. The maximum RMS lamp current is set to 6mA, and the maximum RMS striking voltage is set to 1600V. Table 1 lists some important components, and Table 2 lists the component suppliers' contact information. Detailed Description The MAX8722A controls a full-bridge resonant inverter to convert an unregulated DC input into a near-sinusoidal, high-frequency AC output for powering CCFLs. The lamp brightness is adjusted by turning the lamp on and off with a signal. The brightness of the lamp is proportional to the duty cycle of the DPWM signal, which is Table 1. List of Important Components DESIGNATION DESCRIPTION C1 4.7F 20%, 25V X5R ceramic capacitor Murata GRM32RR61E475K Taiyo Yuden TMK325BJ475MN TDK C3225X7R1E475M C2 1F 10%, 25V X7R ceramic capacitor C3 18pF 1pF, 3kV, high-voltage ceramic capacitor Murata GRM42D1X3F180J TDK C4520C0G3F180F D1 Dual silicon switching diode, common anode, SOT-323 Central Semiconductor CMSD2836 Diodes, Inc. BAW56W NH1/2, NL1/2 Dual n-channel MOSFETs, 30V, 0.095, SOT23-6 Fairchild FDC6561AN T1 CCFL transformer, 1:93 turns ratio TOKO T912MG-1018 Table 2. Component Suppliers SUPPLIER WEBSITE Central Semiconductor www.centralsemi.com Diodes Inc. www.diodes.com Fairchild Semiconductor www.fairchildsemi.com Murata www.murata.com Sumida www.sumida.com Taiyo Yuden www.t-yuden.com TDK www.component.tdk.com TOKO www.tokoam.com 12 set through an analog voltage on the CNTL pin. Figure 2 shows the functional diagram of the MAX8722A. Resonant Operation The MAX8722A drives the four n-channel power MOSFETs that make up the zero-voltage-switching (ZVS) full-bridge inverter as shown in Figure 3. Assume that NH1 and NL2 are turned on at the beginning of a switching cycle as shown in Figure 3(a). The primary current flows through MOSFET NH1, DC blocking capacitor C2, the primary side of transformer T1, and MOSFET NL2. During this interval, the primary current ramps up until the controller turns off NH1. When NH1 turns off, the primary current forward biases the body diode of NL1, which clamps the LX1 voltage just below ground as shown in Figure 3(b). When the controller turns on NL1, its drain-to-source voltage is near zero because its forward-biased body diode clamps the drain. Since NL2 is still on, the primary current flows through NL1, C2, the primary side of T1, and NL2. Once the primary current drops to the minimum current threshold (6mV/RDS(ON)), the controller turns off NL2. The remaining energy in T1 charges up the LX2 node until the body diode of NH2 is forward biased. When NH2 turns on, it does so with near-zero drain-to-source voltage. The primary current reverses polarity as shown in Figure 3(c), beginning a new cycle with the current flowing in the opposite direction, with NH2 and NL1 on. The primary current ramps up until the controller turns off NH2. When NH2 turns off, the primary current forward biases the body diode of NL2, which clamps the LX2 voltage just below ground as shown in Figure 3(d). After the LX2 node goes low, the controller losslessly turns on NL2. Once the primary current drops to the minimum current threshold, the controller turns off NL1. The remaining energy charges up the LX1 node until the body diode of NH1 is forward biased. Finally, NH1 losslessly turns on, beginning a new cycle as shown in Figure 3(a). Note that switching transitions on all four power MOSFETs occur under ZVS condition, which reduces transient power losses and EMI. A simplified CCFL inverter circuit is shown in Figure 4(a). The full-bridge power stage is simplified and represented as a square-wave AC source. The resonant tank circuit can be further simplified to Figure 4(b) by removing the transformer. CS is the primary series capacitor, C'S is the series capacitance reflected to the secondary, CP is the secondary parallel capacitor, N is the transformer turns ratio, L is the transformer secondary leakage inductance, and RL is an idealized resistance that models the CCFL in normal operation. Figure 5 shows the frequency response of the resonant tank's voltage gain under different load conditions. ______________________________________________________________________________________ Low-Cost CCFL Backlight Controller MAX8722A VBATT VBATT NH1 ON NH2 OFF NH1 OFF NH2 ON T1 T1 C2 C2 LX1 LX2 NL1 OFF LX1 NL2 ON LX2 NL1 ON NL2 OFF (a) (c) VBATT VBATT NH1 OFF NH2 OFF NH1 OFF NH2 OFF T1 T1 C2 C2 LX1 LX2 NL1 ON LX1 NL2 ON LX2 NL1 ON NL2 ON (BODY DIODE TURNS ON FIRST) (BODY DIODE TURNS ON FIRST) (b) (d) Figure 3. Resonant Operation ______________________________________________________________________________________ 13 MAX8722A Low-Cost CCFL Backlight Controller CS L 1:N 4 AC SOURCE CCFL fP VOLTAGE GAIN (V/V) CP (a) C C'S = S2 N L 3 RL INCREASING 2 fS 1 0 AC SOURCE CP RL 0 20 40 60 80 100 FREQUENCY (kHz) (b) Figure 4. Equivalent Resonant Tank Circuit Figure 5. Frequency Response of the Resonant Tank The primary series capacitor is 1F, the secondary parallel capacitor is 15pF, the transformer turns ratio is 1:93, and the secondary leakage inductance is 260mH. Notice that there are two peaks, fS and fP, in the frequency response. The first peak, fS, is the series resonant peak determined by the secondary leakage inductance (L) and the series capacitor reflected to the secondary (C'S): the inverter behaves like a voltage source to generate the necessary striking voltage. Theoretically, the output voltage of the resonant converter will increase until the lamp is ionized or until it reaches the IC's secondary voltage limit, without regard to the transformer turns ratio or the input voltage level. Once the lamp is ionized, the equivalent load resistance decreases rapidly and the operating point moves toward the series resonant peak. While in series resonant operation, the inverter behaves like a current source. 1 fS = 2 LC'S The second peak, fP , is the parallel resonant peak determined by the secondary leakage inductance (L), the parallel capacitor (CP), and the series capacitor reflected to the secondary (C'S): 1 fP = 2 L C'S CP C'S + CP The inverter is designed to operate between these two resonant peaks. When the lamp is off, the operating point of the resonant tank is close to the parallel resonant peak due to the lamp's infinite impedance. The circuit displays the characteristics of a parallel-loaded resonant converter. While in parallel-loaded resonant operation, 14 Lamp-Current Regulation The MAX8722A uses a lamp-current control loop to regulate the current delivered to the CCFL. The heart of the control loop is a transconductance error amplifier. The AC lamp current is sensed with a resistor connected in series with the low-voltage terminal of the lamp. The voltage across this resistor is fed to the IFB input and is internally full-wave rectified. The transconductance error amplifier compares the rectified IFB voltage with a 790mV (typ) internal threshold to generate an error current. The error current charges and discharges a capacitor connected between COMP and ground to create an error voltage (VCOMP). VCOMP is then compared with an internal ramp signal to set the high-side MOSFET switch on-time (tON). ______________________________________________________________________________________ Low-Cost CCFL Backlight Controller Upon power-up, two soft-start features acting together smooth the startup behavior. First, VCOMP slowly rises, increasing the duty cycle of the high-side MOSFET switches and providing a measure of soft-start. Second, the MAX8722A charges VFB to the overvoltage threshold (2.3V typ) immediately after the device is enabled. The DC voltage on VFB is gradually discharged through an internal 300k (typ) resistor during startup. This feature is equivalent to slowly raising the overvoltage threshold during startup, so it further improves the soft-start behavior. Feed-Forward Control and Dropout Operation The MAX8722A is designed to maintain tight control of the lamp current under all transient conditions. The feed-forward control instantaneously adjusts the ontime for changes in input voltage (VBATT). This feature provides immunity to input-voltage variations and simplifies loop compensation over wide input voltage ranges. The feed-forward control also improves the line DPWM Dimming Control The MAX8722A controls the brightness of the CCFL by chopping the lamp current on and off using a low-frequency (between 100Hz and 350Hz) DPWM signal either from the internal oscillator or from an external signal source. The CCFL brightness is proportional to the DPWM duty cycle, which can be adjusted from 9.375% to 100% by the CNTL pin. CNTL is an analog input with a usable input voltage range between 0 and 2000mV, which is digitized to select one of 128 brightness levels. As shown in Figure 6, the MAX8722A ignores the first 12 steps, so the first 12 steps all represent the same brightness. When VCNTL is between 0 and 187.5mV, the DPWM duty cycle is always 9.375%. When VCNTL is above 187.5mV, a 15.625mV change on CNTL results in a 0.78125% change in the DPWM duty cycle. When VCNTL is equal to or above 2000mV, the DPWM duty cycle is always 100%. 100 90 80 BRIGHTNESS (%) Lamp Startup A CCFL is a gas discharge lamp that is normally driven in the avalanche mode. To start ionization in a nonionized lamp, the applied voltage (striking voltage) must be increased to the level required for the start of avalanche. At low temperatures, the striking voltage can be several times the typical operating voltage. Because of the MAX8722A's resonant topology, the striking voltage is guaranteed. Before the lamp is ionized, the lamp impedance is infinite. The transformer secondary leakage inductance and the high-voltage parallel capacitor determine the unloaded resonant frequency. Since the unloaded resonant circuit has a high Q, it can generate very high voltages across the lamp. regulation for short on-times and makes startup transients less dependent on the input voltage. Feed-forward control is implemented by increasing the internal voltage ramp rate for higher VBATT. This has the effect of varying t ON as a function of the input voltage while maintaining approximately the same signal levels at V COMP . Since the required voltage change across the compensation capacitor is minimal, the controller's response to input voltage changes is essentially instantaneous. 60 70 50 40 30 20 10 0 0 400 800 1200 1600 2000 CONTROL VOLTAGE (mV) Figure 6. Theoretical Brightness vs. Control Voltage ______________________________________________________________________________________ 15 MAX8722A Transformer Secondary Voltage Limiting The MAX8722A reduces the voltage stress on the transformer's secondary winding by limiting the secondary voltage during startup and open-lamp faults. The AC voltage across the transformer secondary winding is sensed through a capacitive voltage-divider. The small voltage across the larger capacitor of the divider is fed to the VFB input and is internally halfwave rectified. An overvoltage comparator compares the VFB voltage with a 2.3V (typ) internal threshold. Once the sense voltage exceeds the overvoltage threshold, the MAX8722A turns on a 1200A current source that discharges the COMP capacitor. The highside MOSFET on-time shortens as the COMP voltage decreases, reducing the transformer secondary's peak voltage below the threshold set by the capacitive voltage-divider. MAX8722A Low-Cost CCFL Backlight Controller In DPWM operation, COMP controls the rise and fall time of the lamp-current envelope. At the beginning of the DPWM on-cycle, VCOMP rises linearly, gradually increasing tON, which provides soft-start. At the end of the DPWM on-cycle, the COMP capacitor discharges linearly, gradually decreasing tON and providing soft-stop. DPWM Frequency Setting There are three ways to set the DPWM frequency. 1) The DPWM frequency can be set with an external resistor. Connect SYNC to GND and connect a resistor between FREQ and GND. The DPWM frequency is given by the following equation: The frequency range of the external signal is between 100Hz and 350Hz. In this mode, the brightness control input CNTL is disabled, and the brightness is proportional to the duty cycle of the external signal. Table 3 summarizes the three ways of setting the DPWM frequency. UVLO fDPWM = 209Hz x 169k / RFREQ The adjustable range of the DPWM frequency is between 100Hz and 350Hz (RFREQ is between 353k and 101k). CNTL controls the DPWM duty cycle. 2) The DPWM frequency can be clocked by an external high-frequency signal. Connect FREQ to VCC and connect SYNC to the external high-frequency signal. The DPWM frequency is 1/128 of the frequency of the external signal: fDPWM = 3) The DPWM frequency can be synchronized to an external low-frequency signal. To enable this mode, connect SYNC to V CC , connect FREQ to GND through a 100k resistor, and connect DPWM to the external low-frequency signal. The DPWM frequency and duty cycle are equal to those of the external signal. fEXT The MAX8722A includes an undervoltage-lockout (UVLO) circuit. The UVLO circuit monitors the VCC voltage. When V CC is below 4.2V (typ), the MAX8722A disables both high-side and low-side MOSFET drivers and resets the fault latch. Low-Power Shutdown When the MAX8722A is placed in shutdown, all functions of the IC are turned off except for the 5.4V linear regulator. In shutdown, the linear-regulator output voltage drops to about 4.5V and the supply current is 6A (typ). While in shutdown, the fault latch is reset. The device can be placed into shutdown by pulling SHDN to its logic-low level. 128 Lamp-Out Protection where fEXT is the frequency of the external signal. The frequency range of the external signal should be between 13kHz and 45kHz, resulting in a DPWM frequency range between 100Hz and 350Hz. CNTL controls the DPWM duty cycle. For safety, the MAX8722A monitors the lamp-current feedback (IFB) to detect faulty or open CCFL tubes and secondary short circuits in the lamp and IFB sense resistor. As described in the Lamp-Current Regulation section, the voltage on IFB is internally full-wave rectified. If the rectified IFB voltage is below 600mV, the MAX8722A charges the TFLT capacitor with 1A. The Table 3. DPWM Frequency Setting SYNC Connect FREQ to GND through an external resistor. Connect SYNC to GND. DPWM is used as the DPWM signal output. The resistor value sets the frequency. CNTL controls the duty cycle. Connect FREQ to VCC. Connect SYNC to an external high-frequency signal. DPWM is used as the DPWM signal output. The frequency is 1/128 of the frequency of the external signal. CNTL controls the duty cycle. Connect FREQ to GND through a 100k resistor. Connect SYNC to VCC. Connect DPWM to an external low-frequency signal. The frequency and duty cycle are equal to those of the external signal. 16 DPWM DIGITAL PWM FREQUENCY/DUTY CYCLE FREQ ______________________________________________________________________________________ Low-Cost CCFL Backlight Controller During the delay period, the current control loop tries to maintain lamp-current regulation by increasing the high-side MOSFET on-time. Because the open-circuit lamp impedance is very high, the transformer secondary voltage rises as a result of the high Q-factor of the resonant tank. Once the secondary voltage exceeds the overvoltage threshold, the MAX8722A turns on a 1200A current source that discharges the COMP capacitor. The on-time of the high-side MOSFET is reduced, lowering the secondary voltage, as the COMP voltage decreases. Therefore, the peak voltage of the transformer secondary winding never exceeds the limit set by a capacitive voltage-divider during the lamp-out delay period. Primary Overcurrent Protection (ILIM) The MAX8722A senses transformer primary current in each switching cycle. When the regulator turns on the low-side MOSFET, a comparator monitors the voltage drop from LX_ to GND. If the voltage exceeds the current-limit threshold, the regulator turns off the high-side switch at the opposite side of the primary to prevent further increasing the transformer primary current. The current-limit threshold can be adjusted using the ILIM input. Connect a resistive voltage-divider between VCC and GND with the midpoint connected to ILIM. The current-limit threshold measured between LX_ and GND is 1/5 of the voltage at ILIM. The ILIM adjustment range is 0 to 3V. Connect ILIM to VCC to select the default current-limit threshold of 0.2V. Secondary Current Limit (ISEC) The secondary current limit provides fail-safe current limiting in case a failure, such as a short circuit or leakage from the lamp high-voltage terminal to ground, prevents the current control loop from functioning properly. ISEC monitors the voltage across a sense resistor placed between the transformer's low-voltage secondary terminal and ground. The ISEC voltage is internally half-wave rectified and continuously compared to the ISEC regulation threshold (1.25V typ). Any time the ISEC voltage exceeds the threshold, a controlled current is drawn from COMP to reduce the on-time of the bridge's high-side switches. At the same time, the MAX8722A charges the TFLT capacitor with a 116A current source. The MAX8722A latches off when the voltage on TFLT exceeds 4V. Unlike the normal shutdown mode, the linear-regulator output (VCC) remains at 5.4V. Toggling SHDN or cycling the input power reactivates the device. Linear-Regulator Output (VCC) The internal linear regulator steps down the DC input voltage to 5.4V (typ). The linear regulator supplies power to the internal control circuitry of the MAX8722A and is also used to power the MOSFET drivers by connecting VCC to VDD. The VCC voltage drops to 4.5V in shutdown. Applications Information MOSFETs The MAX8722A requires four external n-channel power MOSFETs NL1, NL2, NH1, and NH2 to form a fullbridge inverter circuit to drive the transformer primary. The regulator senses the on-state drain-to-source voltage of the two low-side MOSFETs NL1 and NL2 to detect the transformer primary current, so the RDS(ON) of NL1 and NL2 should be matched. For instance, if dual MOSFETs are used to form the full bridge, NL1 and NL2 should be in one package. Since the MAX8722A uses the low-side MOSFET RDS(ON) for primary overcurrent protection, the lower the MOSFET RDS(ON), the higher the current limit. Therefore, the user should select a dual, logic-level n-channel MOSFET with low RDS(ON) to minimize conduction loss, and keep the primary current limit at a reasonable level. The regulator uses zero-voltage switching (ZVS) to softly turn on each of the four switches in the full bridge. ZVS occurs when the external power MOSFETs are turned on when their respective drain-to-source voltages are near zero (see the Resonant Operation section). ZVS effectively eliminates the instantaneous turn-on loss of MOSFETs caused by COSS (drain-tosource capacitance) and parasitic capacitance discharge, and improves efficiency and reduces switching-related EMI. Setting the Lamp Current The MAX8722A senses the lamp current flowing through resistor R1 (Figure 1) connected between the low-voltage terminal of the lamp and ground. The voltage across R1 is fed to IFB and is internally full-wave rectified. The MAX8722A controls the desired lamp current by regulating the average of the rectified IFB voltage. To set the RMS lamp current, determine R1 as follows: R1 = x 790mV 2 2 x ILAMP(RMS) ______________________________________________________________________________________ 17 MAX8722A MAX8722A latches off if the voltage on TFLT exceeds 4V. Unlike the normal shutdown mode, the linear-regulator output (VCC) remains at 5.4V. Toggling SHDN or cycling the input power reactivates the device. MAX8722A Low-Cost CCFL Backlight Controller where ILAMP(RMS) is the desired RMS lamp current and 790mV is the typical value of the IFB regulation point specified in the Electrical Characteristics table. To set the RMS lamp current to 6mA, the value of R1 should be 148. The closest standard 1% resistors are 147 and 150. The precise shape of the lamp-current waveform, which is dependent on lamp parasitics, influences the actual RMS lamp current. Use a true RMS current meter connected between the R1/IFB junction and the low-voltage side of the lamp to make final adjustments to R1. Setting the Secondary Voltage Limit The MAX8722A limits the transformer secondary voltage during startup and lamp-out faults. The secondary voltage is sensed through the capacitive voltage-divider formed by C3 and C4 (Figure 1). The voltage on VFB is proportional to the CCFL voltage. The selection of the parallel resonant capacitor C3 is described in the Transformer Design and Resonant Component Selection section. C3 is usually between 10pF and 22pF. After the value of C3 is determined, select C4 using the following equation to set the desired maximum RMS secondary voltage VLAMP(RMS)_MAX: C4 = 2 x VLAMP(RMS)_ MAX 2.34 V x C3 where 2.34V is the typical value of the VFB peak voltage when the lamp is open. To set the maximum RMS secondary voltage to 1600V using 18pF for C3, use approximately 15nF for C4. Setting the Secondary Current Limit The MAX8722A limits the secondary current even if the IFB sense resistor (R1) is shorted or transformer secondary current finds its way to ground without passing through R1. ISEC monitors the voltage across the sense resistor R3, connected between the low-voltage terminal of the transformer secondary winding and ground. Determine the value of R3 using the following equation: R3 = 1.241V 2 x ISEC(RMS)_ MAX where ISEC(RMS)_MAX is the desired maximum RMS transformer secondary current during fault conditions, and 1.241V is the typical value of the ISEC peak voltage when the secondary is shorted. To set the maxi- 18 mum RMS secondary current in the circuit of Figure 1 to 22mA, use approximately 40.2 for R3. Transformer Design and Resonant Component Selection The transformer is the most important component of the resonant tank circuit. The first step in designing the transformer is to determine the turns ratio (N). The ratio must be high enough to support the CCFL operating voltage at the minimum supply voltage. N can be calculated as follows: N VLAMP(RMS) 0.9 x VIN(MIN) where VLAMP(RMS) is the maximum RMS lamp voltage in normal operation, and VIN(MIN) is the minimum DC input voltage. If the maximum RMS lamp voltage in normal operation is 650V and the minimum DC input voltage is 8V, the turns ratio should be greater than 90. The turns ratio of the transformer used in the circuit of Figure 1 is 93. The next step in the design procedure is to determine the desired operating frequency range. The MAX8722A is synchronized to the natural resonant frequency of the resonant tank. The resonant frequency changes with operating conditions, such as the input voltage, lamp impedance, etc.; therefore, the switching frequency varies over a certain range. To ensure reliable operation, the resonant frequency range must be within the operating frequency range specified by the CCFL transformer manufacturer. As discussed in the Resonant Operation section, the resonant frequency range is determined by the transformer secondary leakage inductance L, the primary series DC blocking capacitor C2, and the secondary parallel resonant capacitor C3. Since it is difficult to control the transformer leakage inductance, the resonant tank design should be based on the existing secondary leakage inductance of the selected CCFL transformer. Leakageinductance values can have large tolerance and significant variations among different batches, so it is best to work directly with transformer vendors on leakageinductance requirements. The MAX8722A works best when the secondary leakage inductance is between 250mH and 350mH. The series capacitor C2 sets the minimum operating frequency, which is approximately two times the series resonant peak frequency. Choose: ______________________________________________________________________________________ Low-Cost CCFL Backlight Controller Layout Guidelines N2 2 4 x 2 x fMIN x L where fMIN is the minimum operating frequency range. In the circuit of Figure 1, the transformer's turns ratio is 93 and its secondary leakage inductance is approximately 300mH. To set the minimum operating frequency to 45kHz, use 1F for C2. The parallel capacitor C3 sets the maximum operating frequency, which is also the parallel resonant peak frequency. Choose C3 with the following equation: C3 C2 (4 2 x fMAX 2 x L x C2) - N2 In the circuit of Figure 1, to set the maximum operating frequency to 65kHz, use 18pF for C3. The transformer core saturation should also be considered when selecting the operating frequency. The primary winding should have enough turns to prevent transformer saturation under all operating conditions. Use the following expression to calculate the minimum number of turns N1 of the primary winding: N1 > DMAX x VIN(MAX) BS x S x fMIN where DMAX is the maximum duty cycle (approximately 0.4) of the high-side switches, VIN(MAX) is the maximum DC input voltage, BS is the saturation flux density of the core, and S is the minimal cross-section area of the core. COMP Capacitor Selection The COMP capacitor sets the speed of the current loop that is used during startup, while maintaining lamp current regulation, and during transients caused by changing the input voltage. The typical COMP capacitor value is 0.01F. Larger values increase the transient-response delays. Smaller values speed up transient response, but extremely small values can cause loop instability. Other Components The external bootstrap circuits formed by D1 and C5/C6 in Figure 1 power the high-side MOSFET drivers. Connect VDD to BST1/BST2 through dual-diode D1 and couple BST1/BST2 to LX1/LX2 through C5 and C6. C5 = C6 = 0.1F or greater. Careful PC board layout is important to achieve stable operation. The high-voltage section and the switching section of the circuit require particular attention. The high-voltage sections of the layout need to be well separated from the control circuit. Most layouts for singlelamp notebook displays are constrained to long and narrow form factors, so this separation occurs naturally. Follow these guidelines for good PC board layout: 1) Keep the high-current paths short and wide, especially at the ground terminals. This is essential for stable, jitter-free operation and high efficiency. 2) Use a star-ground configuration for power and analog grounds. The power and analog grounds should be completely isolated--meeting only at the center of the star. The center should be placed at the analog ground pin (GND). Using separate copper islands for these grounds may simplify this task. Quiet analog ground is used for V CC , COMP, FREQ, TFLT, and ILIM (if a resistive voltage-divider is used). 3) Route high-speed switching nodes away from sensitive analog areas (VCC, COMP, FREQ, TFLT, and ILIM). Make all pin-strap control input connections (ILIM, etc.) to analog ground or V CC rather than power ground or VDD. 4) Mount the decoupling capacitor from VCC to GND as close as possible to the IC with dedicated traces that are not shared with other signal paths. 5) The current-sense paths for LX1 and LX2 to GND must be made using Kelvin sense connections to guarantee the current-limit accuracy. 6) Ensure the feedback connections are short and direct. To the extent possible, IFB, VFB, and ISEC connections should be far away from the high-voltage traces and the transformer. 7) To the extent possible, high-voltage trace clearance on the transformer's secondary should be widely separated. The high-voltage traces should also be separated from adjacent ground planes to prevent lossy capacitive coupling. 8) The traces to the capacitive voltage-divider on the transformer's secondary need to be widely separated to prevent arcing. Moving these traces to opposite sides of the board can be beneficial in some cases. Chip Information TRANSISTOR COUNT: 2985 PROCESS: BiCMOS ______________________________________________________________________________________ 19 MAX8722A C2 Package Information (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.) QSOP.EPS MAX8722A Low-Cost CCFL Backlight Controller Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 20 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 (c) 2005 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products, Inc. Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Maxim Integrated: MAX8722AEEG+ MAX8722AEEG+T