HIGH EFFICIENCY RED DLO4135/7135 GREEN DLG4137/7137 .43" Single Character DLO4135/7 .68" Single Character DLO7135/7 5x7 Dot Matrix Intelligent Display with Memory/Decoder/Driver DLO4135/4137 DLO7135/7137 Package Dimensions in Inches (mm) Device marking begins over pin 1 .14 min. (3.56) .310 (7.87) .235 (5.97) .043 (1.09) .43 (10.92) 1.00 max. (25.4) 1.00 (2.54) typ. .160 (4.06) Z EIA date code Luminous intensity code DLO 4135 .100 (2.54) typ. SIEMENS YYWW 0.18 .02 (4.57) (.51) .018 (.45) sq. .30 (7.62) .065 typ. (.165) .310 (7.87) Pin 1 indicator Z DLO7135 SIEMENS YYWW .100 (2.54) .100 (2.54) .500 max. (12.7) .295 (7.49) Device marking begins over pin 1 .075 (1.91) ref. 1.00 (2.54) .800 typ. (20.32) .68 (17.27) EIA date code Luminous intensity .125 code (3.18) .300 (7.62) .150 (3.81) .325 (8.26) DLO7135 .012 (.30) .050 (1.27) FEATURES * 5x7 Dot Matrix Characters DLO4135/DLG4137: .43" High DLO7135/DLG7137: .68" High * Wide Viewing Angle 75 * 96 Character ASCII Set Upper Case and Lower Case Characters * Fully Encapsulated, Rugged Solid Plastic Package * Built-in Memory * Built-in Character Generator * * * * * * * * 2-8 .100 (2.54) typ. .700 (17.78) DLO4135 Z .100 (2.54) .080 (2.03) diam. ref. .48 (12.19) Z .50 (12.70) ref. .600 (15.24) Built-in Multiplex and LED Drive Circuitry Built-in Lamp Test Intensity Control (4 levels) Microprocessor Bus Compatible Intensity Coded for Display Uniformity Single 5-Volt Power Supply X/Y Stackable Available in High Efficiency Red and Green DESCRIPTION The DLX413X/DLX713X are single digit 5x7 dot matrix Intelligent Display devices. The DLX413X character is 0.43" high. The DLX713X character is 0.68" high. The builtin CMOS integrated circuit contains memory, ASCII character generator, LED multiplexing and drive circuitry; thereby eliminating the need for additional circuitry. They will display the 96 ASCII characters. These devices are TTL and microprocessor compatible and offer the possibility of cascading the displays, allowing for multi-character messages. These displays were designed for viewing distances of up to 20 feet(DLX413X) or 30 feet (DLX713X). They require a single 5-volt power supply and parallel ASCII input. All products are 100% tested, then subjected to out-going AQLs of .25% for brightness matching, visual alignment and dimensions, .065% for electrical and functional. Important: Refer to Appnote 18, "Using and Handling Intelligent Displays." Since this is a CMOS device, normal precautions should be taken to avoid static damage. Timing Parameters at 25C, VCC=5.0 V 0.5 V Symbol Parameter Maximum Ratings VCC Range (max.) . . . . . . . . . . . . . . . . . . . . . . -0.5 to +7.0 Vdc Voltage, Any Pin, Respect to GND . . . . . . -0.5 to VCC +0.5 Vdc Operating Temperature . . . . . . . . . . . . . . . . . . -40C to +85C Storage Temperature . . . . . . . . . . . . . . . . . . . -40C to +100C Maximum Solder Temperature, .063" below Seating Plane, t<5 sec. . . . . . . . . . . . . . . . . . . . 260C Relative Humidity at 85C (non condensing) . . . . . . . . . . . 85% Optical Characteristics (Typical) at 25C Time Averaged Luminous Intensity/Dot at 5 V . . 1500 mcd typ. Character Size DLO4135/DLG4137 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.43" DLO7135/DLG7137 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.68" Viewing Angle (Note 1). . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Spectral Peak Wavelength DLO4135/7135 (High Efficiency Red) . . . . . . . . .635 nm typ. DLG4137/7137 (Green) . . . . . . . . . . . . . . . . . . . .565 nm typ. Dot to Dot Intensity Ratio . . . . . . . . . . . . . . . . . . . . 1.8:1.0 max. Timing Characteristics -- Write Cycle Waveforms TACC CE Units (ns) TCEH TW TCES Chip Enable Set-Up 10 TDS Data Set Up 100 TW Write Pulse 120 TDH Data Hold 20 TCEH Chip Enable Hold 20 TACC Access Time 150 WE TCES TDS DATA TDH DC Characteristics -40C +25C +85C Parameter Min. Units Conditions 115 mA VCC=5 V, BL0=BL1=5 V 3.5 mA VCC=WR=5.0 V, BL0=BL1=0 V A VIN=0.8 V, VCC=5 V 0.5 V V VCC=5 V 0.5 V 0.8 V VCC=5 V 0.5 V 5.5 V Typ. Max. Min. Typ. Max. Min. Typ. Max. ICC (20 dots on) 135 180 100 140 85 ICC Blank 2.0 5.5 1.5 4.0 0.8 50 100 IIL (all inputs) VIH 25 2.0 2.0 VIL VCC 2.0 0.8 4.5 5.0 5.5 0.8 4.5 5.0 5.5 4.5 5.0 Notes 1. "Off Axis Viewing Angle" definition: The minimum angle in any direction from the normal to the display surface at which any part of any dot in the display is not visible. 2. This display contains a CMOS integrated circuit. Normal CMOS handling precautions should be taken to avoid damage due to high static voltages or electric fields. See Appnote 18. 3. Unused inputs must be tied to an appropriate logic voltage level (either V + or GND). 4. VCC=5.0 VDC 10%. 5. Clean only in water, isopropyl alcohol, freon TF, TE (or equivalent). DLO4135/7135/DLG4137/7137 2-9 Lamp Test Top View -- DLO4135/DLG4137 1 2 3 4 5 6 7 8 When the lamp test (LT) is activated, all dots on the display are illuminated at 17 brightness. The lamp test function is independent of write (WR) and the settings of the blanking inputs (BL0, BL1). 16 15 14 13 12 11 10 9 This convenient test gives a visual indication that all dots are functioning properly. Lamp test also may be used as a cursor function or pointer which does not destroy previously displayed characters. Dimming and Blanking the Display Pin Functions -- DLO4135/DLG4137 Brightness Level BL1 BL0 Blank 0 0 Pin Function Pin Function 17 Brightness 0 1 1 LT Lamp 9 D0 Data LSB 12 Brightness 1 0 2 WR Write 10 D1 Data Full Brightness 1 1 3 BL1 Brightness 11 D2 Data 4 BL0 Brightness 12 D3 Data 5 No Pin 13 D4 Data 6 No Pin 14 D5 Data 7 CE Chip Enable 15 D6 Data MSB 8 GND 16 +VCC Loading Data Loading data into the display is straightforward. Chip enable (CE) should be present and stable during a write pulse (WR). Parallel data information should be stable for the minimum time (TW) and held for TDH after write has gone high. No synchronization is necessary and each character will continue to be displayed until it is replaced with another. Multiple displays may be stacked together with only an additional decoder IC for chip enable decoding. Note : Either BL0 or BL1 should be held high for display to light up. Top View -- DLO7135/DLG7137 Data Loading Example 1 2 3 4 5 6 7 14 13 12 11 10 9 8 Data Input CE WR BL0 BL1 LT Pin Functions -- DLO7135/DLG7137 D6 D5 D4 D3 D2 D1 D0 H X H X H X X X X X X X NC X X L L H X X X X X X X Blank X X X X L X X X X X X X Lamp Test L L H H H H L L L L L H A L L H H H H H H L L H L r Pin Function Pin Function 1 VCC 8 D0 Data Input LSB L L H H H L H H L L H H 3 2 LT Lamp Test 9 D1 Data L L H H H L H L H L H H + 3 CE Chip Enable 10 D2 Data 4 WR Write 11 D3 Data 5 BL1 Brightness 12 D4 Data 6 BL0 Brightness 13 D5 Data 7 GND 14 D6 Data Input MSB X=don't care, NC=no change DLO4135/7135/DLG4137/7137 2-10 16 Digits Interconnection +5 GND D15 2 BL0-BL1 LT D0-D6 WR 11 7 4 A0-A3 D0 16 CE Character Set D0 D1 D2 D3 D6 D5 D4 HEX ASCII CODE 0 0 0 0 0 0 1 1 0 1 0 2 0 1 1 3 1 0 0 4 1 0 1 5 1 1 0 6 1 1 1 7 0 0 0 0 0 1 0 0 0 1 0 1 0 0 2 1 1 0 0 3 0 0 1 0 4 1 0 1 0 5 0 1 1 0 6 1 1 1 0 7 0 0 0 1 8 1 0 0 1 9 0 1 0 1 A 1 1 0 1 B 0 0 1 1 C 1 0 1 1 D 0 1 1 1 E 1 1 1 1 F THESE CODES DISPLAY BLANK Notes: 1. High = 1 level. 2. Low = 0 level. 3. Upon power up, the device will initialize in a random state. DLO4135/7135/DLG4137/7137 2-11