Specification No.: MIS-DG60C203 Specification Manual Insertion Type Hybrid Card Reader (for Magnetic Stripe Cards, Smart Cards ) Model # ZU-98302SEA Revision 1.00 Feb. 2005 Date: Signature for approval Read and agreed by Matsushita Electric Industrial Co., Ltd. Matsushita Industrial Information Equipment Co., Ltd Specification for Hybrid Card Reader Copyright (c) 2004 Panasonic / Matsushita Industrial Information Equipment Co., Ltd. All rights reserved. Panasonic is a registered trademark of Matsushita Electric Industrial Co., Ltd. Other company, product, and service names may be trademarks or service marks of others. Revision History Document No. Date Matsushita Industrial Information Equipment Co., Ltd. Description Specification No.: MIS-DG60C203 Page Specification for Hybrid Card Reader Note:No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written permission of Panasonic / Matsushita Industrial Information Equipment Co., Ltd. In case there is any contradiction appeared based on technical standard change/update etc., our specifications shall take precedence over such change/update. Matsushita Industrial Information Equipment Co., Ltd. Specification No.: MIS-DG60C203 Specification for Hybrid Card Reader Table of Contents 1. Abstract ...............................................................................................................1 2. Constructions.......................................................................................................2 3. Specifications.......................................................................................................3 4. Connector and signals .........................................................................................4 5. Timing chart .........................................................................................................5 6. Input / Output Signals ..........................................................................................7 7. Appearance .......................................................................................................10 8. IC contact location of smart card (ISO type) ...................................................... 11 9. Card specification ..............................................................................................12 10. Unit life and reliability......................................................................................12 11. Precautions ....................................................................................................13 Matsushita Industrial Information Equipment Co., Ltd. Specification No.: MIS-DG60C203 Specification for Hybrid Card Reader IC Card Reader/Writer with magnetic Reader 1. Abstract IC Card Reader/Writer (ZU-98302SEA) consists as follows. (1) Card Reader can access the contacts on smart card and read magnetic stripe. (2) Card Reader has one decoding circuit for magnetic stripe. (3) Electro-mechanical latching mechanism. The mechanism shall be used to lock an smart card in place while a transaction in progress. (4) These mechanical switches detect 3 states the presence of the card within card slot, the state of latch and the card is inserted to the rear end which is placed to the right position. (5) Card present sensor (front switch) is being operated while detecting card width. (6) The opening hole which allows alien substances, such as coins or dust to either fall or to be forced out of the card slot. (7) Location of contacts relative to the face of the card The contact area shall be on the front face of the card at the location specified in ISO 7816-2 specification. (8) Magnetic reading when usually pulling out (ejection) the card. (9) Magnetic card stripe based on ISO 7810, 7811. Card standard ISO7810, ISO7811 Track used Track 2nd Recording method F2F Recording density 75 BPI Recording capacity 40 characters ( 5 bit code) (10) PCB coating for dew condensation-proof. Matsushita Industrial Information Equipment Co., Ltd. Specification No.: MIS-DG60C203 1 Specification for Hybrid Card Reader 2. Constructions IC Contact pins (8 Pins) Vcc RST CLK (RFU) GND Vpp I/O (RFU) Front switch (Card present sensor) S1 Rear switch (Card seated sensor) S2 Latch switch (Latch sensor) S3 Motor Supply (VM) M+ CN M- Voltage Regulator (Backup Power Supply) 4.0 V Latch Motor Motor Drive Circuit 7SH08 Latch Control Circuit LC (Latch Control) Reset /RE (Read Enable) /CLD ISO2 Read Amp Mag. head F2F SYSTEM /RDT2 /RCL2 Decoding Logic DC 5V Signal Ground Matsushita Industrial Information Equipment Co., Ltd. Specification No.: MIS-DG60C203 2 Specification for Hybrid Card Reader 3. Specifications 3.1 Physical dimensions Dimensions Mass : (W) 100.8 mm x (H) 31.7 mm x (D) 118 mm : Approx. 120 g 3.2 Power source 3.2.1 Logic circuit Voltage Current Stand-by Operation : DC 5.0 V (10%), Ripple 250 mV p-p : 1.2 A Max. : 15 mA Max. 3.2.2 Motor Supply Voltage : DC 5.0 V (10%) Current Stand-by : 0 A Operation : 500 mA Max. (at DC 5V) (Note): Motor supply Time of supplying power to the motor is approx. 80 ms and should be taken more than 10 s intervals for testing. 3.3 Card standard Smart card Magnetic card : ISO 7816-2 : ISO 7810, 7811 (ISO 2) 3.4 Interface Smart card Magnetic card Controls : Direct to contacts : CMOS level (0 V - 5 V) : CMOS level (0 V - 5 V) 3.5 Contact resistance IC contact pins : 0.5 ohm Max. 3.6 Connector : I/O connector (CN5) Smart card reader/writer Box type, 2 mm pitch, Dual line, 0.5 square pin & Magnetic card reader (CTEC) MBH26GR3 or equivalent : Connector for Buck up power supply (CN1) Molex 7478-02A 3.7 Environments Operating temperature Storage temperature Operating humidity Storage humidity 3.8 Reading speed of magnetic : -25 C ~ +70 C : -30 C ~ +75 C : 10 % ~ 90 % RH (non condensing) : 5 % ~ 95 % RH (non condensing) : 10 cm/s ~ 80 cm/s stripe 3.9 Installation : Horizontally with printed circuit board side upward Matsushita Industrial Information Equipment Co., Ltd. Specification No.: MIS-DG60C203 3 Specification for Hybrid Card Reader 4. Connector and signals 4.1 I/O connector (I/O connector CN5) No 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 Signal name Vcc *1 /RST *3 CLK (RFU) GND Vpp *2 I/O *4 (RFU) S1 S2 DC 5V LC SG -/RDT2 /RCL2 MG S3 +VM /RE -/CLD ----- Contents Direction Power supply Reset signal supply For Clocking signal supply Smart (Reserved for future use) Card Power and signal ground Programming power supply Serial data input / output (Reserved for future use) Card is detected (card detect sensor 1) Card is loaded (rear detect sensor 2) Circuit power supply Latch control Circuit ground In In In Magnetic read data 2 Magnetic read clock 2 Motor ground Card latch detect sensor 3 Motor power supply Magnetic read enable Out Out In Out In In Magnetic card is loaded. Out In In In / Out Out Out In In In *1, *2 : Connected on 0.1 F ceramic capacitor *3 : Connected on 1 nF ceramic capacitor *4 : Connected on 56 pF ceramic capacitor 4.2 Buck up power supply connector (CN1) No 1 2 Signal name M+ M- Contents Direction Back-up power supply (ex. Capacitor) Ground Matsushita Industrial Information Equipment Co., Ltd. In In Specification No.: MIS-DG60C203 4 Specification for Hybrid Card Reader 5. Timing chart 5.1 Explanation of input/output signal (Smart card read / write) insert PIN11 DC 5 V PIN13 SG PIN9 S1 PIN10 S2 PIN12 LC PIN19 +VM PIN18 S3 PIN1 Smart card C1 Vcc PIN6 Smart card C6 Vpp PIN3 Smart card C2 CLK PIN2 Smart card C3 RST PIN7 Smart card C7 I/O load eject read / write 5.2 Magnetic Card raed PIN20 /RE PIN22 /CLD PIN16 /RCL2 PIN15 /RDT2 Read to see 5.2.1 Detail Matsushita Industrial Information Equipment Co., Ltd. Specification No.: MIS-DG60C203 5 Specification for Hybrid Card Reader 5.2.1 Caution of magnetic reading (1) Be sure to perform sampling of /RDT2 at the falling edge of /RCL2. Pulse width of period "L" of /RCL is about 19 s for the card conformable to ISO2 (75 BPI specification). If sampling method other than edge sampling (such as a method detecting "L" of /RCL2 by means of polling) is used, please check with us since data may be read depending on polling frequency at the host (2) In case that /RCL2 is set to read /RDT2 at the interrupt port of CPU, with the interruption action of the software in sampling of /RDT2 using the falling edge of /RCL2, be sure to perform the interruption action within the /RDT2 available time period.For the /RDT2 available time period, please refer to the following figure. /RCL2 T0 T0 /RDT2 T0 0 1 0 0 T Data available period Where, T0 (fixed) is approx. 9 s in case of ISO2 type card reader. However, T varies with recording density and running speed. Refer to the following formula to calculate suitable T value for the applied card recording density and required maximum card running speed. Then set the interruption action time with sufficient margin. Formula: 2.54 cm/inch T (s) = 1 X Recording dencity (BPI) Reference: Recording density Jitter = 0 Card running speed T Card running speed (cm/s) 75 BPI 18 cm/s 1.9 ms Matsushita Industrial Information Equipment Co., Ltd. Specification No.: MIS-DG60C203 6 Specification for Hybrid Card Reader 6. Input / Output Signals The input / output signals for this smart card reader / writer with magnetic reader consist of: Vcc, Vpp, RST, CLK, I/O, S1, S2, S3, /RE, LC, /RDT2, /RCL2, /CLD 6.1 Signals for smart card Vcc, Vpp, RST, CLK, and I/O are signals for smart card. Please refer to standard ISO / IEC 7816-3 in detailed specifications. 6.1.1 Circuit (1) Vcc, Vpp (Host) (CR) (Smart card) 0.1 F / 25 V GND (2) RST (CR) (Host) (Smart card) 1 nF / 50 V GND (3) I/O (CR) (Host) (Smart card) 56 pF / 50 V GND 6.2 Signals for card feeding 6.2.1 Input circuit Input signal: /RE Equivalent to (CR) DC 5 V 47 K ohm (Host) 47 K ohm Matsushita Industrial Information Equipment Co., Ltd. 74HC244 Specification No.: MIS-DG60C203 7 Specification for Hybrid Card Reader 6.2.2 Input Circuit Input signal: LC Equivalent to (CR) (Host) 47 K ohm 7SH08 47 K ohm SG 6.2.3 Output circuit Output signals: S1, S2, S3 Equivalent to (Host) DC 5 V Chattering protection Circuit (CR) SG 6.3 Input / Output Voltage Input /RE, LC High Level ("0") 3.5 V min. Low Level ("1") 1.0 V max. Output /RDT2, /RCL2 /CLD 4.6 V min. ( IOH= - 4.0 mA ) 0.3 V max. ( IOL= 4.0 mA ) 6.4 Signal description 6.4.1 Signal related with position of card These sensing switches S1, S2 and S3 are snap action switch. The sensing switch outputs connect directly I/O connector CN5. So the interface pull-up resistance and chattering protection circuit are required. Current range of S1 and S2 switches are defined DC 6 V 5 mA ~ DC 90 V 0.1 A to insure proper sensing operation with the environmental condition. Current range of S3 switch is defined DC 5 V 0.04 mA ~ DC 16 V 0.1 A (recommended operating range DC 5 V 0.1 mA) to insure proper sensing operation with the environmental condition. So the interface pull-up resistance should be selected to consider the current range. Matsushita Industrial Information Equipment Co., Ltd. Specification No.: MIS-DG60C203 8 Specification for Hybrid Card Reader (1) S1 Card present sensor (micro-switch) is positioned at the front of card reader. The switch is normally open, and it is grounded when the card is inserted in the card reader. (2) S2 The card seated sensor (micro-switch) is positioned at the rear of card reader. The switch is normally open, and it is grounded when the card is fully inserted. When the switch is grounded, IC contact pins of card reader touch the IC chip on the smart card, and the card is at the specified position to read and write IC. (3) S3 The latch sensor (leaf-switch) indicates that the latching mechanism is activated and in a locked state. The switch is normally open, and it is grounded when the latch mechanism is activated (=card lock status). 6.4.2 Signal related with latch / unlatch of a card (1) LC The latch control signal LC should be normally "L". And the latch mechanism is actuated to lock the card when the signal goes "H" by detecting a signal from host. The latch mechanism is on unlatched position when the signal goes "L". The state of the latch mechanism can be determined by the state of the card-latch sensor S3. Note 1: If power is turned off accidentally during the card is latched and is hold inside of the card reader, the card will be released automatically by unlatch pulse which is generated by card reader itself. Back up power supply is required and connected with the card reader. Panasonic confirm the performance with 8200 F capacitor, however, please select right value of capacitor based on actual condition/environment. In case wrong one is used, unsatisfactory performance may cause. Note 2: The state of card-latch sensor S3 should be check periodically. If the latch mechanism is on latch position while it must be on unlatched position originally, latch mechanism must be change to unlatched position by following order ; 1) Change LC signal from "L" to "H" and keep "H" more than 200 ms. 2) Change LC signal from "H" to "L" in order to an activate the latch mechanism. (set the latch mechanism to unlatch position) 3) Re-check the state of card latch sensor S3 and confirm the latch mechanism is set to unlatch position. 6.4.3 Signal related to reading of magnetic stripes (1) / RDT2 (Read Data) When the /RCL2 signal changes from "High" level to "Low" level : "1" is indicated when the /RDT2 signal is at "Low" level. "0" is indicated when the /RDT2 signal is at "High" level. (2) / RCL2 (Read Clock) This is used to sample the /RDT2 signal at its falling edges. (3) /CLD The /CLD line will be low when a magnetic card is running in the card reader. The /CLD line will be high when the card is stopped or not present in the card reader. Matsushita Industrial Information Equipment Co., Ltd. Specification No.: MIS-DG60C203 9 Specification for Hybrid Card Reader 7. Appearance Matsushita Industrial Information Equipment Co., Ltd. Specification No.: MIS-DG60C198 10 Specification for Hybrid Card Reader 8. IC contact location of smart card (ISO type) [ unit : mm ] (Transitional contacts location) a = 10.25 max g = 21.77 max b = 12.25 min h = 23.47 min c = 17.87 max i = 24.31 max d = 19.87 min j = 26.01 min e = 19.23 max k =26.85 max f= 20.93 min l = 28.55 min Upper edge e Left edge C1 C5 C2 C6 C3 C7 C4 C8 f g h i j k l a b c d Matsushita Industrial Information Equipment Co., Ltd. Specification No.: MIS-DG60C198 11 Specification for Hybrid Card Reader 9. Card specification Materials and dimensions of the card should be submitted to ISO standards. But defined items in this specification are prior to these standards. [ unit : mm] 5.66 max. 8.46 8.197 8.97 8.46 11.76 12.27 12.52 12.01 15.32 15.82 85.47 85.72 7.44 0.51 (Track1, 2) 7.44 1.0 (Track 3) Track1 Track2 Track3 Mag stripe (Back side) IC contacts (Front side) 6.93 min. center line of first data bit center line of last data bit 53.92 54.18 (Unit : mm) 9.1 Physical characteristics (1) Thickness (2) Warpage 9.2 Magnetic characteristics (1) Coercive force (Hc) (2) Residual flux (r) (3) Square ratio (r/m) : 0.76 mm (tolerance 0.08 mm) : 2.5 mm max. (include relief height of embossed characters) : 2.4 x 104 A/m ~ 2.4 x 105 A/m : 1.25 x 10-8 Wb/cm (tolerance 0.15 x 10-8 Wb/cm) : More than 0.70 10. Unit life and reliability 10.1 Life of the magnetic head and IC contact pins (1) Magnetic head : 500,000 operations (2 passes / 1 operation) (2) IC contact pin : 500,000 operations (Condition) In a clean office environment (room). In damp or dusty atmosphere, the life may be 1/3 to 1/5 of the above figure. Above life cycles are the numbers which are tested in a "clean office environment". These numbers may be shortened dependent on the actual environment. Especially in a dusty environment, even in the indoor application, dust or sand may shorten the life against the mechanical parts and most of the card transport mechanisms. In these cases, warranty of the card reader may be void unless the proper protection and countermeasures are performed by the terminal side. Dusty environment : Refer to ex.)IEC 68,EN30721-3-3 class 3S2 or worse. Matsushita Industrial Information Equipment Co., Ltd. Specification No.: MIS-DG60C198 12 Specification for Hybrid Card Reader 11. Precautions Keep the following precautions when using this unit. 11.1 Handling (1) Do not drop or give excessive shocks to this unit. (There are a few cases that card lock mechanism will be released when the excessive shock is given.) (2) Do not disassemble this unit. 11.2 Cautions 11.2.1 Card (1) Use specified card (ISO). (2) Store the card carefully so as not to soil, injure or deform it. In particular, solid deposit on the magnetic stripe surface may result in a trouble. 11.2.2 Cleaning (1) Clean the magnetic head and IC contact pins by periodically passing a cleaning card. For example, in a clean office room, pass the cleaning card about once a week. If the magnetic head is heavily stained, clean the head by soaking the felt part of the cleaning card in alcohol properly and pass the card. For example, in the case that the card readers are used in the environment full of dust, please make a cleaning of the card reader with a cleaning card with alcohol everyday. The exclusive cleaning card shuld be used for IC contacts pins. (2) If some kind of oil adheres to the parts for transferring cards, card transfer will be unstable. Please remove the oil with a cleaning card with alcohol. 11.2.3 Installation (1) Do not install the card reader in dusty, hot or damp place, or near magnetic field or object generating inductive noise (printer, LED display unit, CRT, etc.). Do not use the unit in a dusty place, otherwise the reading and writing accuracy may be deteriorated. Keeps the unit away from objects generating magnetism, which may cause read errors and may damage the magnetic card data. (2) Do not touch the printed circuit board with bare hand. Note particularly static electricity. (3) Do not supply power from other outlet than connector terminal. Pay special attention to the polarity of power source and wrong connection of connector. (4) Do not use the unit in a place where it is exposed to sunlight directly or it is splashed by water. (5) Install the card reader horizontally with printed circuit board side upward. Matsushita Industrial Information Equipment Co., Ltd. Specification No.: MIS-DG60C198 13 Specification for Hybrid Card Reader 11.2.4 Others (1) Check the noise, static electricity, etc., with the card reader being incorporated in the equipment. Noise from the power supply may cause the reading errors. Measures to reduce the noise from power supply should be made for the equipment the card reader is built in. It is especially efficient to put a noise-filter in the AC input line. (2) The guaranteed temperature for operation range is -25 C ~ 70 Cand humidity range is 10 % ~ 90 % RH. Do not use the unit if condensation gathers on it. We recommend you to use the card reader under the environmental condition of temperature 10 C ~ 40 C which is the best for transferring cards and reading data. Especially, in the condition of low temperature, provide heating system separately to warm up card reader. (3) A shutter is not built in this card reader. In the case that the card readers are used in the environment full of dust, the lifetime of the magnetic head, IC contact pins and mechanism for transferring cards will decrease. Matsushita Industrial Information Equipment Co., Ltd. Specification No.: MIS-DG60C198 14