Transient Voltage Suppression Diodes Surface Mount - 3000W > SMDJ series SMDJ Series RoHS Pb e3 Description Uni-directional Bi-directional The SMDJ series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Features Agency Approvals AGENCY AGENCY FILE NUMBER E230531 Maximum Ratings and Thermal Characteristics (TA=25OC unless otherwise noted) Parameter Symbol Value Unit Peak Pulse Power Dissipation at TA=25C by 10/1000s Waveform (Fig.2)(Note 1), (Note 2), (Note 5) PPPM 3000 W Power Dissipation on Infinite Heat Sink at TL=50OC PD 6.5 W Peak Forward Surge Current, 8.3ms Single Half Sine Wave (Note 3) IFSM 300 A Maximum Instantaneous Forward Voltage at 100A for Unidirectional Only(Note 4) VF 3.5/5.0 V Operating Temperature Range TJ -65 to 150 C Storage Temperature Range TSTG -65 to 175 C Typical Thermal Resistance Junction to Lead RJL 15 C/W Typical Thermal Resistance Junction to Ambient RJA 75 C/W Notes: 1. Non-repetitive current pulse , per Fig. 4 and derated above TJ (initial) =25OC per Fig. 3. 2. Mounted on copper pad area of 0.31x0.31" (8.0 x 8.0mm) to each terminal. 3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional device only, duty cycle=4 per minute maximum. 4. VF < 3.5V for single die parts and VF< 5.0V for stacked-die parts. 5. The PPPM of stacked-die parts is 4000W and please contact littelfuse for the detail stacked-die parts. Functional Diagram * 3000W peak pulse power capability at 10/1000s waveform, repetition rate (duty cycles):0.01% * For surface mounted applications in order to optimize board space * Low profile package * Typical failure mode is short from over-specified voltage or current * Whisker test is conducted based on JEDEC JESD201A per its table 4a and 4c * IEC-61000-4-2 ESD 30kV(Air), 30kV (Contact) * ESD protection of data lines in accordance with IEC 61000-4-2 * EFT protection of data lines in accordance with IEC 61000-4-4 * Built-in strain relief * Glass passivated chip junction * Fast response time: typically less than 1.0ps from 0V to BV min * Excellent clamping capability * Low incremental surge resistance * Typical IR less than 2A when VBR min>12V * High temperature to reflow soldering guaranteed: 260C/40sec * VBR @ TJ= VBR@25C x (1+T x (TJ - 25)) (T:Temperature Coefficient, typical value is 0.1%) * Plastic package is flammability rated V-0 per Underwriters Laboratories *M eet MSL level1, per J-STD-020, LF maximun peak of 260C * Matte tin lead-free plated * Halogen free and RoHS compliant * Pb-free E3 means 2nd level interconnect is Pb-free and the terminal finish material is tin(Sn) (IPC/JEDEC J-STD609A.01) Applications TVS devices are ideal for the protection of I/O Interfaces, VCC bus and other vulnerable circuits used in Telecom, Computer, Industrial and Consumer electronic applications. Additional Infomarion Bi-directional Cathode Datasheet Resources Samples Anode Uni-directional (c) 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/20/15 Transient Voltage Suppression Diodes Surface Mount - 3000W > SMDJ series Electrical Characteristics (T =25C unless otherwise noted) A Part Number (Uni) Part Number (Bi) SMDJ5.0A SMDJ6.0A SMDJ6.5A SMDJ7.0A SMDJ7.5A SMDJ8.0A SMDJ8.5A SMDJ9.0A SMDJ10A SMDJ11A SMDJ12A SMDJ13A SMDJ14A SMDJ15A SMDJ16A SMDJ17A SMDJ18A SMDJ20A SMDJ22A SMDJ24A SMDJ26A SMDJ28A SMDJ30A SMDJ33A SMDJ36A SMDJ40A SMDJ43A SMDJ45A SMDJ48A SMDJ51A SMDJ54A SMDJ58A SMDJ60A SMDJ64A SMDJ70A SMDJ75A SMDJ78A SMDJ85A SMDJ90A SMDJ100A SMDJ110A SMDJ120A SMDJ130A SMDJ150A SMDJ160A SMDJ170A SMDJ180A SMDJ220A SMDJ5.0CA SMDJ6.0CA SMDJ6.5CA SMDJ7.0CA SMDJ7.5CA SMDJ8.0CA SMDJ8.5CA SMDJ9.0CA SMDJ10CA SMDJ11CA SMDJ12CA SMDJ13CA SMDJ14CA SMDJ15CA SMDJ16CA SMDJ17CA SMDJ18CA SMDJ20CA SMDJ22CA SMDJ24CA SMDJ26CA SMDJ28CA SMDJ30CA SMDJ33CA SMDJ36CA SMDJ40CA SMDJ43CA SMDJ45CA SMDJ48CA SMDJ51CA SMDJ54CA SMDJ58CA SMDJ60CA SMDJ64CA SMDJ70CA SMDJ75CA SMDJ78CA SMDJ85CA SMDJ90CA SMDJ100CA SMDJ110CA SMDJ120CA SMDJ130CA SMDJ150CA SMDJ160CA SMDJ170CA SMDJ180CA SMDJ220CA UNI BI Reverse Stand off Voltage VR (Volts) RDE RDG RDK PDM PDP PDR PDT PDV PDX PDZ PEE PEG PEK PEM PEP PER PET PEV PEX PEZ PFE PFG PFK PFM PFP PFR PFT PFV PFX PFZ RGE PGG PGK PGM PGP PGR PGT PGV PGX PGZ PHE PHG PHK PHM PHP PHR PHT PKE DDE DDG DDK DDM DDP DDR DDT DDV DDX DDZ DEE DEG DEK DEM DEP DER DET DEV DEX DEZ DFE DFG DFK DFM DFP DFR DFT DFV DFX DFZ DGE DGG DGK DGM DGP DGR DGT DGV DGX DGZ DHE DHG DHK DHM DHP DHR DHT DKE 5.0 6.0 6.5 7.0 7.5 8.0 8.5 9.0 10.0 11.0 12.0 13.0 14.0 15.0 16.0 17.0 18.0 20.0 22.0 24.0 26.0 28.0 30.0 33.0 36.0 40.0 43.0 45.0 48.0 51.0 54.0 58.0 60.0 64.0 70.0 75.0 78.0 85.0 90.0 100.0 110.0 120.0 130.0 150.0 160.0 170.0 180.0 220.0 Marking For bidirectional type having VR of 10 volts and less, the IR limit is double. For parts without A , the VBR is 10% and VC is 5% higher than with A parts (c) 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/20/15 Breakdown Voltage VBR (Volts) @ IT MIN MAX Test Current IT (mA) 6.40 6.67 7.22 7.78 8.33 8.89 9.44 10.00 11.10 12.20 13.30 14.40 15.60 16.70 17.80 18.90 20.00 22.20 24.40 26.70 28.90 31.10 33.30 36.70 40.00 44.40 47.80 50.00 53.30 56.70 60.00 64.40 66.70 71.10 77.80 83.30 86.70 94.40 100.00 111.00 122.00 133.00 144.00 167.00 178.00 189.00 200.00 244.00 7.00 7.37 7.98 8.60 9.21 9.83 10.40 11.10 12.30 13.50 14.70 15.90 17.20 18.50 19.70 20.90 22.10 24.50 26.90 29.50 31.90 34.40 36.80 40.60 44.20 49.10 52.80 55.30 58.90 62.70 66.30 71.20 73.70 78.60 86.00 92.10 95.80 104.00 111.00 123.00 135.00 147.00 159.00 185.00 197.00 209.00 221.00 270.00 10 10 10 10 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Maximum Maximum Maximum Agency Clamping Peak Reverse Approval Voltage VC Pulse Leakage IR @ Ipp Current Ipp @ VR (V) (A) (A) 9.2 10.3 11.2 12.0 12.9 13.6 14.4 15.4 17.0 18.2 19.9 21.5 23.2 24.4 26.0 27.6 29.2 32.4 35.5 38.9 42.1 45.4 48.4 53.3 58.1 64.5 69.4 72.7 77.4 82.4 87.1 93.6 96.8 103.0 113.0 121.0 126.0 137.0 146.0 162.0 177.0 193.0 209.0 243.0 259.0 275.0 292.0 356.0 326.1 291.3 267.9 250.0 232.6 220.6 208.3 194.8 176.5 164.8 150.8 139.5 129.3 123.0 115.4 108.7 102.7 92.6 84.5 77.1 71.3 66.1 62.0 56.3 51.6 46.5 43.2 41.3 38.8 36.4 34.4 32.1 31.0 29.1 26.5 24.8 23.8 21.9 20.5 18.5 16.9 15.5 14.4 12.3 11.6 10.9 10.3 8.4 800 800 500 200 100 50 20 10 5 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X Transient Voltage Suppression Diodes Surface Mount - 3000W > SMDJ series I-V Curve Characteristics Bi-directional Uni-directional Ipp IT IR Vc VBR VR Vc VBR VR IR IT V IR VF IT VR VBR Vc V Ipp Ipp PPPM VR VBR VC IR VF Peak Pulse Power Dissipation -- Max power dissipation Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (IT) Clamping Voltage -- Peak voltage measured across the TVS at a specified Ippm (peak impulse current) Reverse Leakage Current -- Current measured at VR Forward Voltage Drop for Uni-directional Ratings and Characteristic Curves (T =25C unless otherwise noted) A Figure 1 - TVS Transients Clamping Waveform Figure 2 - Peak Pulse Power Rating Voltage Transients PPPM-Peak Pulse Power (kW) 100 Voltage or Current Voltage Across TVS stacked-die, 4kW at 10x1000s, 25C 10 Current Through TVS Single die, 3kW at 10x1000s, 25C 1 TJ initial = Tamb 0.1 0.001 Time 0.01 0.1 1 10 td-Pulse Width (ms) continues on next page. (c) 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/20/15 Transient Voltage Suppression Diodes Surface Mount - 3000W > SMDJ series Ratings and Characteristic Curves (T =25C unless otherwise noted) (Continued) A Figure 3 - Peak Pulse Power Derating Curve Figure 4 - Pulse Waveform 150 IPPM- Peak Pulse Current, % IRSM Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % 100 80 60 40 20 0 0 25 50 75 100 125 150 TJ - Initial Junction Temperature (C) 2 Uni-direconal V=VR Bi-direconal V=VR 10 100 td 1.0 0 3.0 4.0 10 1 0.1 0.01 0.001 1000 0.01 0.1 VBR - Reverse Breakdown Voltage(V) 1 10 100 1000 TP - Pulse Duration (s) Figure 7 - Maximum Non-Repetitive Peak Forward 500 Surge Current Uni-Directional Only Figure 8 - Peak Forward Voltage Drop vs Peak Forward Current (Typical Values) 100 450 IF- Peak Forward Current(A) IFSM - Peak Forward Surve Current (A) 2.0 100 1 10 10/1000sec. Waveform as defined by R.E.A t-Time (ms) Transient Thermal Impedance (C/W) Cj(pF) Bi-direconal V=0V 1 ( ) 50 Figure 6 - Typical Transient Thermal Impedance Uni-direconal V=0V 100 Half Value IPPM IPPM 175 100000 10000 TJ=25C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM Peak Value IPPM 100 0 Figure 5 - Typical Junction Capacitance 1000 tr=10sec 400 350 300 250 200 150 100 Single die 10 Stack-die 1 0.1 50 0.01 0 1 10 Number of Cycles at 60 Hz (c) 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/20/15 100 0.00 1.00 2.00 3.00 4.00 5.00 6.00 VF-Peak Forward Voltage(V) 7.00 8.00 Transient Voltage Suppression Diodes Surface Mount - 3000W > SMDJ series Soldering Parameters Lead-free assembly Pre Heat - Temperature Min (Ts(min)) 150C - Temperature Max (Ts(max)) 200C - Time (min to max) (ts) 60 - 180 secs Average ramp up rate (Liquidus Temp (TA) to peak 3C/second max TS(max) to TA - Ramp-up Rate 3C/second max Reflow - Temperature (TA) (Liquidus) 217C - Time (min to max) (ts) 60 - 150 seconds Peak Temperature (TP) 260+0/-5 C Time within 5C of actual peak Temperature (tp) 20 - 40 seconds Ramp-down Rate 6C/second max Time 25C to peak Temperature (TP) 8 minutes Max. Do not exceed 260C Physical Specifications tp TP Ramp-up TL Temperature (T) Reflow Condition tL Critical Zone TL to TP Ts(max) Ramp-down Ts(min) ts Preheat 25C t 25C to Peak Time (t) Environmental Specifications High Temp. Storage JESD22-A103 HTRB JESD22-A108 Weight 0.007 ounce, 0.21 grams Temperature Cycling JESD22-A104 Case JEDEC DO214AB. Molded plastic body over glass passivated junction MSL JEDEC-J-STD-020, Level 1 Polarity Color band denotes positive end (cathode) except Bidirectional. H3TRB JESD22-A101 Terminal Matte Tin-plated leads, Solderable per JESD22-B102 RSH JESD22-A111 Dimensions DO-214AB (SMC J-Bend) Cathode Band (for Uni-directional products only) C A B H D F E G J K L I Dimensions Inches Min Millimeters Max Min Max A 0.114 0.126 2.900 3.200 B 0.260 0.280 6.600 7.110 C 0.220 0.245 5.590 6.220 D 0.079 0.103 2.060 2.620 E 0.030 0.060 0.760 1.520 F - 0.008 - 0.203 G 0.305 0.320 7.750 8.130 H 0.006 0.012 0.152 0.305 I 0.129 - 3.300 - J 0.094 - 2.400 - K - 0.165 L 0.094 - 4.200 2.400 - Solder Pads (all dimensions in mm) (c) 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/20/15 Transient Voltage Suppression Diodes Surface Mount - 3000W > SMDJ series Part Numbering System Part Marking System SMDJ XXX C A Cathode Band F (for Uni-directional products only) 5% VBR VOLTAGE TOLERANCE BI-DIRECTIONAL XXX VR VOLTAGE YMXXX SERIES Littelfuse Logo Marking Code Trace Code Marking Y:Year Code M: Month Code XXX: Lot Code Packaging Options Part number Component Package SMDJxxxXX DO-214AB 3000 Tape & Reel - 16mm tape/13" reel EIA STD RS-481 SMDJxxxXX-T7 DO-214AB 500 Tape & Reel - 16mm tape/7" reel EIA STD RS-481 Packaging Option Quantity Packaging Specification Tape and Reel Specification 0.157 (4.0) 0.63 (16.0) Cathode 0.315 (8.0) Optional 7" 7.0 (187) 13" 13.0 (330) 0.80 (20.2) Arbor Hole Dia. 0.65 (16.4) (c) 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/20/15 0.059 DIA (1.5) Cover tape Dimensions are in inches (and millimeters). Direction of Feed Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Littelfuse: SMDJ54 SMDJ6.0 SMDJ30C SMDJ18CA SMDJ150A SMDJ85C SMDJ45C SMDJ75 SMDJ20C SMDJ13CA SMDJ40 SMDJ7.5A SMDJ110 SMDJ26 SMDJ90A SMDJ26CA SMDJ40CA SMDJ100 SMDJ64A SMDJ9.0C SMDJ17CA SMDJ54CA SMDJ6.5C SMDJ160 SMDJ14C SMDJ70 SMDJ14CA SMDJ45CA SMDJ30CA SMDJ120 SMDJ58 SMDJ11C SMDJ9.0CA SMDJ20CA SMDJ7.5C SMDJ11A SMDJ110CA SMDJ24A SMDJ6.0CA SMDJ60C SMDJ78 SMDJ22C SMDJ43 SMDJ58CA SMDJ8.0A SMDJ16A SMDJ7.0C SMDJ170CA SMDJ8.0 SMDJ120C SMDJ28 SMDJ75CA SMDJ58C SMDJ15C SMDJ5.0A SMDJ17 SMDJ15A SMDJ43CA SMDJ160A SMDJ28CA SMDJ33A SMDJ70A SMDJ10C SMDJ5.0 SMDJ78C SMDJ12 SMDJ22CA SMDJ22A SMDJ48A SMDJ33CA SMDJ8.0C SMDJ150C SMDJ85 SMDJ9.0 SMDJ64C SMDJ17C SMDJ160C SMDJ48CA SMDJ6.5A SMDJ17A SMDJ40A SMDJ130 SMDJ78A SMDJ6.5 SMDJ5.0C SMDJ12C SMDJ90C SMDJ48C SMDJ10CA SMDJ12A SMDJ54A SMDJ26A SMDJ6.0A SMDJ170A SMDJ75A SMDJ13 SMDJ45 SMDJ170 SMDJ33C SMDJ15CA